Name: methods for measuring the orientation and rotation rate of 3d-printed particles in turbulence
Uploaded: 2016-06-24T13:00:00.000+00:00
Duration: 12 min 34 s
Description: Watch this Scientific Journal Video about Methods for Measuring the Orientation and Rotation Rate of 3D-printed Particles in Turbulence at JoVE.com

Agradecemos a Susantha Wijesinghe que diseñó y construyó el sistema de compresión de imágenes que utilizamos. Reconocemos el apoyo de la subvención NSF DMR-1208990.

<ol>
	<li>Marcus, G., Parsa, S., Kramel, S., Ni, R., Voth, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurements+of+the+Solid-body+Rotation+of+Anisotropic+Particles+in+3D+Turbulence.">Measurements of the Solid-body Rotation of Anisotropic Particles in 3D Turbulence.</a> New J. Phys. 16, 102001 (2014).</li><li>Bretherton, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+motion+of+rigid+particles+in+a+shear+flow+at+low+Reynolds+number.">The motion of rigid particles in a shear flow at low Reynolds number.</a> J. Fluid Mech. 14 (02), 284-304 (1962).</li><li>Oullette, N., Xu, H., Bodenschatz, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+quantitative+study+of+three-dimensional+Lagrangian+particle+tracking+algorithms.">A quantitative study of three-dimensional Lagrangian particle tracking algorithms.</a> Exp. in Fluids. 40 (2), 301-313 (2006).</li><li>Parsa, S., Calzavarini, E., Toschi, F., Voth, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rotation+Rate+of+Rods+in+Turbulent+Fluid.">Rotation Rate of Rods in Turbulent Fluid.</a> Phys. Rev. Lett. 109 (13), 134501 (2012).</li><li>Parsa, S., Voth, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Inertial+Range+Scaling+in+Rotations+of+Long+Rods+in+Turbulence.">Inertial Range Scaling in Rotations of Long Rods in Turbulence.</a> Phys. Rev. Lett. 112 (2), 024501 (2014).</li><li>Tsai, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+versatile+camera+calibration+technique+for+high-accuracy+3d+machine+vision+metrology+using+off-the-shelf+tv+cameras+and+lenses.">A versatile camera calibration technique for high-accuracy 3d machine vision metrology using off-the-shelf tv cameras and lenses.</a> IEEE Journal of Robotics and Automation. 3 (4), 323-344 (1987).</li><li>Blum, D., Kunwar, S., Johnson, J., Voth, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+nonuniversal+large+scales+on+conditional+structure+functions+in+turbulence.">Effects of nonuniversal large scales on conditional structure functions in turbulence.</a> Phys. Fluids. 22 (1), 015107 (2010).</li><li>Mann, J., Ott, S., Andersen, J. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+study+of+relative,+turbulent+diffusion.">Experimental study of relative, turbulent diffusion.</a> RISO Internal Report. , (1999).</li><li>Chan, K., Stich, D., Voth, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Real-time+image+compression+for+high-speed+particle+tracking.">Real-time image compression for high-speed particle tracking.</a> Rev. Sci. Instrum. 78 (2), 023704 (2007).</li><li>Goldstein, H., Poole, C., Safko, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Classical Mechanics, 3rd Edition. , 134-180 (2002).</li><li>Parsa, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Rotational dynamics of rod particles in fluid flows. , (2013).</li><li>Wijesinghe, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Measurement of the effects of large scale anisotropy on the small scales of turbulence. , (2012).</li><li>Wallace, J., Foss, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Measurement+of+Vorticity+in+Turbulent+Flows.">The Measurement of Vorticity in Turbulent Flows.</a> Annu. Rev. Fluid Mech. 27, 469-514 (1995).</li><li>Su, L., Dahm, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Scalar+imaging+velocimetry+measurements+of+the+velocity+gradient+tensor+field+in+turbulent+flows.+I.+Assessment+of+errors.">Scalar imaging velocimetry measurements of the velocity gradient tensor field in turbulent flows. I. Assessment of errors.</a> Phys. Fluids. 8, 1869-1882 (1996).</li><li>L&#252;thi, B., Tsinober, A., Kinzelbach, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Lagrangian+measurement+of+vorticity+dynamics+in+turbulent+flow.">Lagrangian measurement of vorticity dynamics in turbulent flow.</a> J. Fluid Mech. 528, 87-118 (2005).</li><li>Frish, M., Webb, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Direct+measurement+of+vorticity+by+optical+probe.">Direct measurement of vorticity by optical probe.</a> J. Fluid Mech. 107, 173-200 (1981).</li><li>Zimmerman, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tracking+the+dynamics+of+translation+and+absolute+orientation+of+a+sphere+in+a+turbulent+flow.">Tracking the dynamics of translation and absolute orientation of a sphere in a turbulent flow.</a> Rev. Sci. Instrum. 82 (3), 033906 (2011).</li><li>Zimmerman, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rotational+Intermittency+and+Turbulence+Induced+Lift+Experienced+by+Large+Particles+in+a+Turbulent+Flow.">Rotational Intermittency and Turbulence Induced Lift Experienced by Large Particles in a Turbulent Flow.</a> Phys. Rev. Lett. 106 (15), 154501 (2011).</li><li>Klein, S., Gibert, M. a. t. h. i. e. u., B&#233;rut, A., Bodenschatz, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simultaneous+3D+measurement+of+the+translation+and+rotation+of+finite-size+particles+and+the+flow+field+in+a+fully+developed+turbulent+water+flow.">Simultaneous 3D measurement of the translation and rotation of finite-size particles and the flow field in a fully developed turbulent water flow.</a> Meas. Sci. Technol. 24 (2), 1-10 (2013).</li><li>Bellani, G., Byron, M., Collignon, A., Meyer, C., Variano, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Shape+effects+on+turbulent+modulation+by+large+nearly+neutrally+buoyant+particles.">Shape effects on turbulent modulation by large nearly neutrally buoyant particles.</a> J. Fluid Mech. 712, 41-60 (2012).</li></ol>

Los autores no tienen intereses en competencia de interés económico alguno.

Las mediciones de la vorticidad y la rotación de las partículas en el flujo de fluido turbulento han sido reconocidos como los objetivos importantes de la mecánica de fluidos experimentales. La rotación de cuerpo sólido de pequeñas esferas de la turbulencia es igual a la mitad de la vorticidad del fluido, pero la simetría de rotación de esferas ha hecho la medición directa de su rotación de cuerpo sólido difícil. Tradicionalmente, la vorticidad del fluido se ha medido utilizando compleja, de múltiples senso...

En una publicación reciente, se introdujo el uso de partículas hechas de múltiples brazos delgados para medir el movimiento de rotación de las partículas en la turbulencia 1. Estas partículas se pueden fabricar utilizando impresoras 3D, y es posible medir con precisión su posición, la orientación y la velocidad de rotación el uso de múltiples cámaras. El uso de herramientas de la teoría de cuerpo delgado, se puede demostrar que estas partículas han elipsoides eficaces 2 correspondiente, y los movimientos de rotación de estas partículas son idénticas a las de sus respectivos elipsoides eficaces. Las partículas con brazos simétricos de igual longitud giran como esferas. Una de tales partículas es un gato, que tiene tres brazos perpendiculares entre sí unidos en su centro. Ajuste de las longitudes relativas de los brazos de un conector puede formar una partícula equivalente a cualquier elipsoide tri-axial. Si la longitud de un brazo se fija igual a cero, esto crea una cruz, cuyo elipsoide equivalente es un disco. Las partículas hechas de delgadasbrazos ocupan una pequeña fracción del volumen sólido de sus homólogos elipsoidales sólidos. Como resultado, se sedimentan más lentamente, lo que facilita su partido densidad. Esto permite que el estudio de las partículas mucho más grandes que es conveniente con partículas sólidas elipsoidales. Además, las imágenes se puede realizar a concentraciones de partículas mucho más altos debido a que las partículas bloquean una fracción más pequeña de la luz de otras partículas. En este trabajo, se documentan los métodos para la fabricación y el rastreo de partículas 3D-impreso. Herramientas para el seguimiento de el movimiento de traslación de partículas esféricas a partir de las posiciones de partículas, como se ve por varias cámaras han sido desarrolladas por varios grupos 3,4. Parsa et al. 5 extendió este enfoque para realizar un seguimiento de barras utilizando la posición y orientación de las varillas vistos por varias cámaras. A continuación, presentamos los métodos para la fabricación de partículas de una amplia variedad de formas y la reconstrucción de sus orientaciones 3D. Esto ofrece THe posibilidad de ampliar seguimiento 3D de partículas con formas complejas a una amplia gama de nuevas aplicaciones. Esta técnica tiene un gran potencial para un mayor desarrollo debido a la amplia gama de formas de partícula que puede ser diseñado. Muchas de estas formas tienen una aplicación directa en los flujos ambientales, donde el plancton, las semillas y los cristales de hielo vienen en una gran variedad de formas. Las conexiones entre las rotaciones de partículas y propiedades fundamentales a pequeña escala de los flujos turbulentos 6 sugieren que el estudio de las rotaciones de estas partículas proporciona nuevas formas de ver el proceso en cascada turbulenta.

<table><tbody><tr><td>Condor Nd:YAG 50 W laser</td><td>Quantronics</td><td>532-30-M</td><td></td></tr><tr><td>High speed camera</td><td>Basler</td><td>A504k</td><td></td></tr><tr><td>High speed camera</td><td>Mikrotron</td><td>EoSens Mc1362</td><td></td></tr><tr><td>Rhodamine-B</td><td>ScienceLab.com</td><td>SLR1465</td><td></td></tr><tr><td>Sodium Hydroxide</td><td>Macron</td><td>7708</td><td>Pellets.</td></tr><tr><td>500 Connex 3D printer</td><td>Objet</td><td></td><td>Used to make smaller particles. Particles ordered from RP+M (rapid prototyping plus manufacturing).</td></tr><tr><td>VeroClear</td><td>Stratasys</td><td>RGD810</td><td>Objet build material.</td></tr><tr><td>Clear Form 1 Photopolymer Resin</td><td>Formlabs</td><td></td><td></td></tr><tr><td>Cylindrical and spherical lenses</td><td></td><td></td><td></td></tr><tr><td>200 mm macro camera lenses</td><td></td><td></td><td>F-mount.</td></tr><tr><td>Ultrasonic bath</td><td>Sonicator</td><td></td><td></td></tr><tr><td>Calcium Chloride</td><td>Spectrum Chemical Mfg. Corp.</td><td>CAS 10043-52-2</td><td>Pellets.</td></tr><tr><td>LabVIEW System Design Software</td><td>National Instruments</td><td></td><td>Used to trigger cameras, control grid, and trigger laser.</td></tr><tr><td>XCAP Software</td><td>EPIX</td><td></td><td>Used with LabVIEW to trigger cameras.</td></tr><tr><td>MATLAB</td><td>Mathworks</td><td></td><td>Used for all image and data analysis. Programs for extracting 3D orientations from multiple images are included with this publication.</td></tr><tr><td>OpenPTV: Open Source Particle Tracking Velocimetry</td><td>OpenPTV Consortium</td><td></td><td></td></tr><tr><td>ParaView</td><td>Kitware</td><td></td><td></td></tr><tr><td>AutoCAD</td><td>AutoDesk</td><td></td><td>Used to design all particles. Screenshots of particle designs are all of AutoCAD.</td></tr><tr><td>Mesh with 0.040 x 0.053 inch holes</td><td>Industrial Netting</td><td>XN5170&amp;ndash;43.5</td><td></td></tr><tr><td>Camera filters</td><td>Schneider Optics</td><td>B+W 040M</td><td></td></tr></tbody></table>

methods for measuring the orientation and rotation rate of 3d-printed particles in turbulence

Los métodos experimentales se presentan para medir el movimiento de rotación y de traslación de partículas anisotrópicas en flujos de fluido turbulentos. tecnología de impresión 3D se utiliza para la fabricación de partículas con brazos delgados conectados a un centro común. Formas exploradas son cruces (dos barras perpendiculares), gatos (tres varillas perpendiculares), tríadas (tres barras en simetría plana triangular), y tétradas (cuatro brazos en la simetría tetraédrica). Se describen métodos para la producción del orden de 10.000 partículas por fluorescencia teñidos. Mediciones con resolución temporal de su orientación y la velocidad de rotación de cuerpo sólido se obtienen a partir de cuatro vídeos sincronizados de su movimiento en un flujo turbulento entre las rejillas oscilantes con R λ = 91. En este flujo del número relativamente bajo de Reynolds, las partículas son lo suficientemente pequeñas advectada que se aproximan las partículas trazadoras elipsoidales. Se presentan los resultados de las trayectorias 3D con resolución temporal de la posición y la orientación de las partículasasí como mediciones de sus velocidades de rotación.

La figura 3a muestra una imagen de una tétrada de una de nuestras cámaras encima de un solar de los ángulos de Euler obtiene a partir de una sección de su trayectoria (Figura 3c). En la Figura 3b, los resultados del algoritmo de orientación de investigación, se describe en el Protocolo de 5-5,3, se superponen la imagen tétrada en. Los brazos de la tétrada en la Figura 3a no siguen las distribuciones de intensidad...

Watch this Scientific Journal Video about Methods for Measuring the Orientation and Rotation Rate of 3D-printed Particles in Turbulence at JoVE.com

Methods for Measuring the Orientation and Rotation Rate of 3D-printed Particles in Turbulence

We use 3D printing to fabricate anisotropic particles in the shapes of jacks, crosses, tetrads, and triads, whose alignments and rotations in turbulent fluid flow can be measured from multiple simultaneous video images.

Los métodos para medir la orientación y rotación Tasa de partículas en la turbulencia impresa en 3D

Experimental methods are presented for measuring the rotational and translational motion of anisotropic particles in turbulent fluid flows. 3D printing ...

methods-for-measuring-orientation-rotation-rate-3d-printed-particles

Education

Research

JoVE Core

JoVE Journal

Physics

Civil Engineering

Mechanical Engineering

Engineering

Unit 1

3-Dimensional Kinetics of a Rigid Body

Fluid Dynamics

Dynamics of Rotational Motions

SCIENTISTS IN ACTION

10.0K vistas.  Wesleyan University. We use 3D printing to fabricate anisotropic particles in the shapes of jacks, crosses, tetrads, and triads, whose alignments and rotations in turbulent fluid flow can be measured from multiple simultaneous video images.

Video: Methods for Measuring the Orientation and Rotation Rate of 3D-printed Particles in Turbulence

Encapsulation and Permeability Characteristics of Plasma Polymerized Hollow Particles

In this protocol, core-shell nanostructures are synthesized by plasma enhanced chemical vapor deposition. We produce an amorphous barrier by plasma polymerization of isopropanol on various solid substrates, including silica and potassium chloride. This versatile technique is used to treat nanoparticles and nanopowders with sizes ranging from 37 nm to 1 micron, by depositing films whose thickness can be anywhere from 1 nm to upwards of 100 nm. Dissolution of the core allows us to study the rate of permeation through the film. In these experiments, we determine the diffusion coefficient of KCl through the barrier film by coating KCL nanocrystals and subsequently monitoring the ionic conductivity of the coated particles suspended in water. The primary interest in this process is the encapsulation and delayed release of solutes. The thickness of the shell is one of the independent variables by which we control the rate of release. It has a strong effect on the rate of release, which increases from a six-hour release (shell thickness is 20 nm) to a long-term release over 30 days (shell thickness is 95 nm). The release profile shows a characteristic behavior: a fast release (35% of the final materials) during the first five minutes after the beginning of the dissolution, and a slower release till all of the core materials come out.

We have used plasma enhanced chemical vapor deposition to deposit thin films ranging from a few nm to several 100 nm on nano-sized particles of various materials. We subsequently etch the core material to produce hollow nanoshells whose permeability is controlled by the thickness of the shell. We characterize the permeability of these coatings to small solutes and demonstrate that these barriers can provide sustained release of the core material over several days.

Encapsulación y permeabilidad Características de las partículas de plasma polimerizado Hollow

In this protocol, core-shell nanostructures are synthesized by plasma enhanced chemical vapor deposition. We produce an amorphous barrier by plasma ...

Investigación

Ingeniería

Experimental Measurement of Settling Velocity of Spherical Particles in Unconfined and Confined Surfactant-based Shear Thinning Viscoelastic Fluids

An experimental study is performed to measure the terminal settling velocities of spherical particles in surfactant based shear thinning viscoelastic (VES) fluids. The measurements are made for particles settling in unbounded fluids&#160;and fluids between parallel walls. VES fluids over a wide range of rheological properties are prepared and rheologically characterized. The rheological characterization involves steady shear-viscosity and dynamic oscillatory-shear measurements to quantify the viscous and elastic properties respectively. The settling velocities under unbounded conditions are measured in beakers having diameters at least 25x the diameter of particles. For measuring settling velocities between parallel walls, two experimental cells with different wall spacing are constructed. Spherical particles of varying sizes are gently dropped in the fluids and allowed to settle. The process is recorded with a high resolution video camera and the trajectory of the particle is recorded using image analysis software. Terminal settling velocities are calculated from the data.
The impact of elasticity on settling velocity in unbounded fluids is quantified by comparing the experimental settling velocity to the settling velocity calculated by the inelastic drag predictions of Renaud et al.1&#160;Results show that elasticity of fluids can increase or decrease the settling velocity. The magnitude of reduction/increase is a function of the rheological properties of the fluids and properties of particles. Confining walls are observed to cause a retardation effect on settling and the retardation is measured in terms of wall factors.

This paper demonstrates the experimental procedure to measure terminal settling velocities of spherical particles in surfactant-based shear thinning viscoelastic fluids. Fluids over a wide range of rheological properties are prepared and settling velocities are measured for a range of particle sizes in unbounded fluids and fluids between parallel walls.

Medición Experimental De La Velocidad De Sedimentación De Partículas Esféricas En Fluidos Viscoelásticos De Adelgazamiento No Confinados Y Confinados A Base De Surfactante

An experimental study is performed to measure the terminal settling velocities of spherical particles in surfactant based shear thinning viscoelastic ...

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

When a laser is mode-locked, it emits a train of ultra-short pulses at a repetition rate determined by the laser cavity length. This article outlines a new and inexpensive procedure to force mode locking in a pre-adjusted nonlinear polarization rotation fiber laser. This procedure is based on the detection of a sudden change in the output polarization state when mode locking occurs. This change is used to command the alignment of the intra-cavity polarization controller in order to find mode-locking conditions. More specifically, the value of the first Stokes parameter varies when the angle of the polarization controller is swept and, moreover, it undergoes an abrupt variation when the laser enters the mode-locked state. Monitoring this abrupt variation provides a practical easy-to-detect signal that can be used to command the alignment of the polarization controller and drive the laser towards mode locking. This monitoring is achieved by feeding a small portion of the signal to a polarization analyzer measuring the first Stokes parameter. A sudden change in the read out of this parameter from the analyzer will occur when the laser enters the mode-locked state. At this moment, the required angle of the polarization controller is kept fixed. The alignment is completed. This procedure provides an alternate way to existing automating procedures that use equipment such as an optical spectrum analyzer, an RF spectrum analyzer, a photodiode connected to an electronic pulse-counter or a nonlinear detecting scheme based on two-photon absorption or second harmonic generation. It is suitable for lasers mode locked by nonlinear polarization rotation. It is relatively easy to implement, it requires inexpensive means, especially at a wavelength of 1550 nm, and it lowers the production and operation costs incurred in comparison to the above-mentioned techniques.

A protocol to detect and automate mode locking in a pre-adjusted nonlinear polarization rotation fiber laser is presented. The detection of a sudden change in the output polarization state when mode locking occurs is used to command the alignment of an intra-cavity polarization controller in order to find mode-locking conditions.

Automatización de modo de bloqueo de rotación en un láser de fibra no lineal de polarización a través de mediciones de polarización de salida

When a laser is mode-locked, it emits a train of ultra-short pulses at a repetition rate determined by the laser cavity length. This article outlines a ...

Three-dimensional Particle Tracking Velocimetry for Turbulence Applications: Case of a Jet Flow

3D-PTV is a quantitative flow measurement technique that aims to track the Lagrangian paths of a set of particles in three dimensions using stereoscopic recording of image sequences. The basic components, features, constraints and optimization tips of a 3D-PTV topology consisting of a high-speed camera with a four-view splitter are described and discussed in this article. The technique is applied to the intermediate flow field (5 &#60;x/d &#60;25) of a circular jet at Re &#8776; 7,000. Lagrangian flow features and turbulence quantities in an Eulerian frame are estimated around ten diameters downstream of the jet origin and at various radial distances from the jet core. Lagrangian properties include trajectory, velocity and acceleration of selected particles as well as curvature of the flow path, which are obtained from the Frenet-Serret equation. Estimation of the 3D velocity and turbulence fields around the jet core axis at a cross-plane located at ten diameters downstream of the jet is compared with literature, and the power spectrum of the large-scale streamwise velocity motions is obtained at various radial distances from the jet core.

A three-dimensional particle tracking velocimetry (3D-PTV) system based on a high-speed camera with a four-view splitter is described here. The technique is applied to a jet flow from a circular pipe in the vicinity of ten diameters downstream at Reynolds number Re &#8776; 7,000.

Tridimensional de velocimetría de seguimiento de partículas para aplicaciones de turbulencia: Caso de un Flujo Jet

3D-PTV is a quantitative flow measurement technique that aims to track the Lagrangian paths of a set of particles in three dimensions using stereoscopic ...

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Two different experimental methods for determining the threshold of particle motion as a function of geometrical properties of the bed from laminar to turbulent flow conditions are presented. For that purpose, the incipient motion of a single bead is studied on regular substrates that consist of a monolayer of fixed spheres of uniform size that are regularly arranged in triangular and quadratic symmetries. The threshold is characterized by the critical Shields number. The criterion for the onset of motion is defined as the displacement from the original equilibrium position to the neighboring one. The displacement and the mode of motion are identified with an imaging system. The laminar flow is induced using a rotational rheometer with a parallel disk configuration. The shear Reynolds number remains below 1. The turbulent flow is induced in a low-speed wind tunnel with open jet test section. The air velocity is regulated with a frequency converter on the blower fan. The velocity profile is measured with a hot wire probe connected to a hot film anemometer. The shear Reynolds number ranges between 40 and 150. The logarithmic velocity law and the modified wall law presented by Rotta are used to infer the shear velocity from the experimental data. The latter is of special interest when the mobile bead is partially exposed to the turbulent flow in the so-called hydraulically transitional flow regime. The shear stress is estimated at onset of motion. Some illustrative results showing the strong impact of the angle of repose, and the exposure of the bead to shear flow are represented in both regimes.

Two different methods for characterizing the incipient particle motion of a single bead as a function of the sediment bed geometry from laminar to turbulent flow are presented.

Visual basado en la caracterización de la propuesta del partícula incipiente en sustratos Regular: de Laminar a turbulentas condiciones

Two different experimental methods for determining the threshold of particle motion as a function of geometrical properties of the bed from laminar to ...

Simultaneous Measurement of Turbulence and Particle Kinematics Using Flow Imaging Techniques

Numerous problems in scientific and engineering fields involve understanding the kinematics of particles in turbulent flows, such as contaminants, marine micro-organisms, and/or sediments in the ocean, or fluidized bed reactors and combustion processes in engineered systems. In order to study the effect of turbulence on the kinematics of particles in such flows, simultaneous measurements of both the flow and particle kinematics are required. Non-intrusive, optical flow measurement techniques for measuring turbulence, or for tracking particles, exist but measuring both simultaneously can be challenging due to interference between the techniques. The method presented herein provides a low cost and relatively simple method to make simultaneous measurements of the flow and particle kinematics. A cross section of the flow is measured using a particle image velocimetry (PIV) technique, which provides two components of velocity in the measurement plane. This technique utilizes a pulsed-laser for illumination of the seeded flow field that is imaged by a digital camera. The particle kinematics are simultaneously imaged using a light emitting diode (LED) line light that illuminates a planar cross section of the flow that overlaps with the PIV field-of-view (FOV). The line light is of low enough power that it does not affect the PIV measurements, but powerful enough to illuminate the larger particles of interest imaged using the high-speed camera. High-speed images that contain the laser pulses from the PIV technique are easily filtered by examining the summed intensity level of each high-speed image. By making the frame rate of the high-speed camera incommensurate with that of the PIV camera frame rate, the number of contaminated frames in the high-speed time series can be minimized. The technique is suitable for mean flows that are predominantly two-dimensional, contain particles that are at least 5 times the mean diameter of the PIV seeding tracers, and are low in concentration.

The technique described herein offers a low cost and relatively simple method to simultaneously measure particle kinematics and turbulence in flows with low particle concentrations. The turbulence is measured using particle image velocimetry (PIV), and particle kinematics are calculated from images obtained with a high-speed camera in an overlapping field-of-view.

Medida simultánea de la cinemática de la partícula usando técnicas de imagen de flujo y turbulencia

Numerous problems in scientific and engineering fields involve understanding the kinematics of particles in turbulent flows, such as contaminants, marine ...

3D Printing - Evaluating Particle Emissions of a 3D Printing Pen

Three-dimensional (3D) printing as a type of additive manufacturing shows continuing increase in application and consumer popularity. The fused filament fabrication (FFF) is an inexpensive method used most frequently by consumers. Studies with 3D printers have shown that during the printing process particulate and volatile substances are released. Handheld 3D printing pens also use the FFF method but the consumer&#8217;s proximity to the 3D pens gives reason to higher exposure compared to a 3D printer. At the same time, 3D printing pens are often marketed for children who could be more sensitive to the printing emission. The aim of this study was to implement a low cost method to analyze the emissions of 3D printing pens. Polylactide (PLA) and acrylonitrile butadiene styrene (ABS) filaments of different colors were tested. In addition, filaments containing metal and carbon nanotubes (CNTs) were analyzed. An 18.5 L chamber and sampling close to the emission source was used to characterize emissions and concentrations near the breathing zone of the user.
Particle emissions and particle size distributions were measured and the potential release of metal particles and CNTs investigated. Particle number concentrations were found in a range of 105 - 106 particles/cm3, which is comparable to previous reports from 3D printers. Transmission electron microscopy (TEM) analysis showed nanoparticles of the different thermoplastic materials as well as of metal particles and CNTs. High contents of metal were observed by inductively coupled plasma mass spectrometry (ICP-MS).
These results call for a cautious use of 3D pens due to potential risk to the consumers.

This protocol presents a method to analyze the emission of 3D printing pens. Particle concentration and particle size distribution of the released particle is measured. Released particles are further analyzed with transmission electron microscopy (TEM). Metal content in filaments is quantified by inductively coupled plasma mass spectrometry (ICP-MS).

Impresión 3D - Evaluación de las emisiones de partículas de una pluma de impresión 3D

Three-dimensional (3D) printing as a type of additive manufacturing shows continuing increase in application and consumer popularity. The fused filament ...

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders

The development of novel imaging techniques of molecular and colloidal transport, including nanoparticles, is an area of active investigation in microfluidic and millifluidic studies. With the advent of three-dimensional (3D) printing, a new domain of materials has emerged, thereby increasing the demand for novel polymers. Specifically, polymeric powders, with average particle sizes on the order of a micron, are experiencing a growing interest from academic and industrial communities. Controlling material tunability at the mesoscopic to microscopic length scales creates opportunities to develop innovative materials, such as gradient materials. Recently, a need for micron-sized polymeric powders has been growing, as clear applications for the material are developing. Three-dimensional printing provides a high-throughput process with a direct link to new applications, driving investigations into the physio-chemical and transport interactions on a mesoscale. The protocol that is discussed in this article provides a non-invasive technique to image fluid flow in packed powder beds, providing high temporal and spatial resolution while leveraging mobile technology that is readily available from mobile devices, such as smartphones. By utilizing a common mobile device, the imaging costs that would normally be associated with an optical microscope are eliminated, resulting in a frugal-science approach. The proposed protocol has successfully characterized a variety of combinations of fluids and powders, creating a diagnostic platform for quickly imaging and identifying an optimal combination of fluid and powder.

The proposed technique will provide a novel, efficient, frugal, and non-invasive approach for imaging fluidic flow through a packed powder bed, yielding high spatial and temporal resolution.

Técnica de imagen frugal del flujo capilar a través de polvos de impresión polimérica tridimensionales

The development of novel imaging techniques of molecular and colloidal transport, including nanoparticles, is an area of active investigation in ...

Visualización de la dinámica de los polímeros para optimizar la calidad de la impresión 3D

Real-Time Imaging of Bonding in 3D-Printed Layers

In recent times, 3D printing technology has revolutionized our ability to design and produce products, but optimizing the print quality can be challenging. The process of extrusion 3D printing involves pressuring molten material through a thin nozzle and depositing it onto previously extruded material. This method relies on bonding between the consecutive layers to create a strong and visually appealing final product. This is no easy task, as many parameters, such as the nozzle temperature, layer thickness, and printing speed, must be fine-tuned to achieve optimal results. In this study, a method for visualizing the polymer dynamics during extrusion is presented, giving insight into the layer bonding process. Using laser speckle imaging, the plastic flow and fusion can be resolved non-invasively, internally, and with high spatiotemporal resolution. This measurement, which is easy to perform, provides an in-depth understanding of the underlying mechanics influencing the final print quality. This methodology was tested with a range of cooling fan speeds, and the results showed increased polymer motion with lower fan speeds and, thus, explained the poor printing quality when the cooling fan was turned off. These findings show that this methodology allows for optimizing the printing settings and understanding the material behavior. This information can be used for the development and testing of novel printing materials or advanced slicing procedures. With this approach, a deeper understanding of extrusion can be built to take 3D printing to the next level.

Autor destacado: Imágenes en tiempo real de la unión en capas impresas en 3D  

With a non-invasive and real-time technique, nanoscopic polymer motion inside a polymer filament is imaged during 3D printing. Fine-tuning this motion is crucial for producing constructs with optimal performance and appearance. This method reaches the core of plastic layer fusion, thus offering insights into optimal printing conditions and material design criteria.