Okay.Hi, my name is Celeste Peterson and I'm a fellow at Harvard University studying microbial bio film communities. So I am profiling the bacterial communities by looking at their 60 N sequence and how this sequence changes over time in space. And to do that, I'm using DDGE.

This is not a normal acry of my well, it needs to be kept at 60 degrees when it's run and the buffer needs to be pumped continuously. So we're gonna warm up the buffer for about an hour until it's at 60 degrees, and then we can run the towel. Now I'm gonna wash this plate with dilute uc solution, peeling around for impurities, andone, light that up.

Anything like that can cause regularities. It is important to wipe off all the water. So when I assemble the gel, I'll put that chip on the outside of the gel.

So the gel will be in between these two pieces of glass and the chip will be on the outside and it won't affect the gel in between. So now I'm gonna assemble the gel in these clamps and then I squeeze them together and tighten by turning to the right. As with any gel, it's important to make sure that the bottom is flush.

To prevent making, we now turn the gel around and put it in here to get sealed with the gasket. So it's important when you do this that the gel, that the plates are actually lined up with the gasket here. So these knobs on the side then go in and you press down to type the seal.

So this is a 30 mil syringe. And this part and this part come with the bio red kit and it just on like this. And that's just to get rid of the excess water in the tubes.

So put the tubing onto the gel to load the gel. First you put an adapter into the tubing and then a needle look with that small adapter and put it right in the center of the gel just so it's fairly below the bottom glass. Then this wire adapter goes into the long tubing and it's going to connect to equal syringes containing the high and the low density solution.

So these are pre-prepared solutions. The blue one, I've added a dye here that just indicates that this is the most denaturing solution and this is the least fitting train solution, the low density one. And they have everything in them.

And now I'm gonna to make, gonna be Actually I twice as much the week. And once you've got the tempt, you have about five to seven minutes to fill the gel before the colon rises. And now we fill the syringe juice with the solution.

So I'm gonna fill it with about 15 the solution. And then to get rid of any air bubbles, I'll turn it upside down and squeeze gently until that top air bubble is gone. Now this little screw here is gonna go into this groove.

This adapter is gonna line up with this clamp here, and it's gonna get C clamped in very tightly. And then this tubing is gonna attach to the syringe. And the same thing is done on the other side with the high density matrix where it's time to deliver.

And so I'm gonna be turning this wheel in a steady clockwise motion. And first the blue solution is gonna go out first because that's the the most in nature, and it's gonna form the bottom part of the gel. And then after a little while, the clear solution will start filling in the gel and the Gradient will be formed.

One moment is the gently on an angle to And as soon as you finish pouring the gel to wash out your tubes immediately because they will polymerize Going, It's the group there. And then press down. So this little, And on the other side, I'll do the same thing.Okay.

Hi, my name is Celeste Peterson and I'm a fellow at Harvard University studying microbial bio communities. So I am profiling the bacterial communities by looking at their 60 F sequence and how the sequence changes over time in space. And to do that, I'm using DDGE.

So DGE is Dena gel electrophoresis. And basically the idea is that there's a gradient and the DNA, as it runs down the gradient gets de natured. And so different 16 species will stop at different points along the gradient.

And so it ends up being a fingerprint of the different sexiness species in the community. So the goal of my experiment is to see who is in the community and how that's changing over time and space. And I can run the sexiness DDD gel and then I can cut out the bands and identify the species that are represented in each community.

So one of the biggest issues when, when doing A DDG gel is to figure out the gradient that's the best. And so that is just something that needs to be played around with and figuring out for a particular community which type of gradient. So the one I'm using today is 35 to 55%urea.

One of the big problems that can happen with this technique is that smears come up in in the leans. And I found for that, for whatever reason, one of the best things to do is to run the gels for a really long time and then the smears disappear. Well, today I'm just using it for general bacterial communities, but this can also be used for a specific family of bacteria to see how those change over time, and those tend to be very clean gels.

You can also look at mutations in single genes with DDGE.