This work is supported by the Eunice Kennedy Shriver National Institute of Child Health and Human Development, National Institutes of Health (K25HD097288, R21HD112663).

The protocol has been approved by the Institutional Animal Care and Use Committee of Wayne State University.
1. Experimental preparation
<ol>
	<li>Use a 70% ethanol solution to clean and sterilize the scissors and tweezers. Also, prepare disposable pipettes and a syringe.</li>
	<li>Prepare a wash medium by adding 3.595 g of NaCl to 495 mL of deionized water. Then, add 5 ml of Penicillin-Streptomycin (5 U/mL) to the medium. Fill a 100 mm Petri dish with the wash medium and warm it to 37 &#176;C.</li>
	<li>Prepare culture dishes according to Figure 1, which illustrates the overall configuration.
	<ol>
		<li>Prepare a piece of filter paper, cut it into a rectangular shape of approximately 17 mm &#215; 20 mm, and remove the four corners. Create a hollow center in the filter paper, approximately 7 mm &#215; 10 mm in size for securing the embryo (Figure 1, left). 
		NOTE: The collection of embryos is described in step 2.</li>
		<li>Attach a commercial available ring (&#934; = 1 inch, see Table of Materials) with a flexible film (i.e., paraffin film) layer, ensuring that the flexible film also has a hollow center. This ring with the film will be used to hold the filter paper with the embryo.</li>
		<li>Finally, place the prepared ring into a 35 mm Petri dish (Figure 1, right). 
		&#8203;NOTE: The filter paper is for securing and holding the extracted embryo by placing the filter paper on the membrane and leaving the embryo in the center hollow area (which will be detailed in step 2). The four corners were cut to fit the size of the outside ring (not necessary if it is already fitted). A 35 mm glass-bottom culture dish is used for better laser beam propagation. The dish has an inner well (&#934; = 23 mm), which can be filled with albumen for ex ovo culture. The diameter of the ring must be larger than the diameter of the inner well so that the well can be covered by the flexible film on the ring (Figure 1, inset). The size of the filter paper is not restricted and can be modified according to the size of the chosen ring and the culture dish. Alternatively, the bottom of the dish can be pre-coated with an agarose layer (thickness: ~1 mm). By removing agarose from the center of the layer using a blade, a well with a similar shape to the hollow center of the flexible film can be created for loading albumen. One critical point is that the four sides of the hollow filter paper need to have enough width (&#62; 5 mm) to ensure the attachment of the embryo.</li>
	</ol>
	</li>
</ol>
2. Extraction and ex ovo culture of the chicken embryo
NOTE: This step is modified from previously published reports40,41.
<ol>
	<li>After pre-culture, retrieve the egg from the incubator and place it on its long axis on the egg carton tray. Clean the eggshell with 70% ethanol, ensuring to cover the entire surface, and then allow it to rest for 15 min.</li>
	<li>Hold the egg on its short axis and crack it at the bottom. Open the egg over a clean 100 mm Petri dish to extract its contents, as illustrated in Figure 2. Ensure not to rotate the egg while holding and cracking it.</li>
	<li>Using a pipette, transfer and collect approximately 10 mL of the thin albumen (i.e., the liquid albumen42) into a 15 mL tube for ex ovo culture use. Fill the center well of the culture dish with the collected thin albumen (about 0.9 mL), as shown in Figure 3. The filling process should be slow, avoiding the formation of any bubbles inside the well. Ensure that the culture dish with albumen is warmed to 37 &#176;C. 
	NOTE: This dish will be used for culturing the embryo ex ovo. New culture dishes filled with wash medium will be used during Brillouin imaging (see step 3).</li>
	<li>Using tissue paper, gently remove the thick albumen (i.e., viscous albumen) attached to the embryo by carefully separating the albumen from the vitelline membrane, as demonstrated in Figure 4. Avoid direct contact with the vitelline membrane.</li>
	<li>After removing all the thick albumen, carefully affix the filter paper to the vitelline membrane. Ensure the body axis of the embryo aligns with the long axis of the center rectangle on the filter paper. Use scissors to cut the membrane surrounding the filter paper.</li>
	<li>Using tweezers, gently pull the isolated filter paper away from the yolk in an oblique direction. Flip the filter paper upside down to position the embryo with its dorsal side down (for inverted microscope configuration). Carefully immerse the entire filter paper from one side of the long axis into the 100 mm Petri dish with the wash medium in an oblique fashion.</li>
	<li>Wash away any remaining yolk by gently spraying the wash medium parallel to the filter paper using a clean pipette. Avoid directly spraying the wash medium onto the membrane.</li>
	<li>After clearing all the yolk, carefully remove the filter paper from the wash medium and use tissue paper to absorb any excess medium from the edges. Then, place the filter paper with the embryo onto the culture dish, ensuring that the dorsal side of the embryo is facing downward, as illustrated in Figure 5. To maintain humidity, place a moistened tissue paper in the dish.</li>
	<li>Transfer the culture dish to the on-stage incubator for ex ovo culture.</li>
</ol>
3. Brillouin measurement of the embryo
<ol>
	<li>Prepare another set of culture dishes and fill them with wash medium. Ensure the wash medium is warmed to 37 &#176;C.</li>
	<li>When the embryo reaches the desired developmental stage, transfer the filter paper with the embryo to the culture dish filled with wash medium. Place the culture dish into the on-stage incubator of the Brillouin microscope (see Table of Materials).
	<ol>
		<li>Before conducting the Brillouin measurement, save a bright-field image of the entire embryo for reference. The detailed configuration of the Brillouin microscope has been previously described30 and is summarized in the Results section (Figure 6).</li>
	</ol>
	</li>
	<li>Measure the Brillouin signal of water and methanol, which will be used in step 4 for the calibration process.</li>
	<li>Adjust the incident laser power and electron-multiplying charge-coupled device (EMCCD, see Table of Materials) camera exposure time to achieve at least 10,000 counts of Brillouin signal. Using the bright-field image as a guide, set up the scan range and step size. Acquire a Brillouin image of the region of interest by scanning the embryo using a 2D translational stage. 
	NOTE: The horizontal scanning range can be determined based on the bright-field image, and the vertical (i.e., depth) scanning range can be determined based on the signal strength obtained from a quick and coarse scan. To prevent any photodamage to the embryo, limit the incident power to 25 mW, and set the exposure time of the EMCCD camera to 50 ms. Choose a step size of 2 &#181;m in the horizontal direction and 1 &#181;m in the vertical direction to balance imaging quality and acquisition time.</li>
	<li>After completing the scan, carefully remove the filter paper with the embryo and use tissue paper to absorb any excess wash medium. Then, place the filter paper back into the culture dish filled with thin albumen for continuous culturing in the on-stage incubator.</li>
	<li>Repeat steps 3.2-3.5 at regular time intervals (e.g., 1.5 h) to capture time-lapse Brillouin images as the embryo develops.</li>
	<li>Reconstruct the 2D Brillouin image following step 4.</li>
</ol>
4. Brillouin image reconstruction
<ol>
	<li>Calibrate the Brillouin spectrometer using Brillouin signals of water and methanol to calculate the free spectral range (FSR) and the pixel-to-frequency conversion ratio (PR) of the spectrometer30. The calibrated values of FSR and PR will be used to calculate the Brillouin shift of the embryo at each pixel. 
	NOTE: Figure 7A displays a raw Brillouin spectrum captured by the EMCCD camera. By vertically summing the spectrum and then doing a Lorentzian fitting, the peak distance &#916;d of the two dots can be obtained (Figure 7B). By getting the peak distance of water &#916;dwater and methanol &#916;dmethanol, the FSR and PR can be computed based on the equations30:&#160;PR = 2&#183;(&#969;methanol-&#969;water)/(&#916;dwater- &#916;dmethanol), and FSR = 2&#183;&#969;water&#160;+ PR&#183;&#916;dwater, with the known Brillouin shift of water &#969;water = 6.01 GHz and methanol &#969;methanol = 4.49 GHz at 660 nm.</li>
	<li>Obtain the peak distance of the Brillouin signal at each pixel of the sample. Calculate the Brillouin shift based on the calibrated FSR and PR: &#969;sample = 0.5 (FSR - PR x &#916;dsample)30, where &#969;sample is the Brillouin shift of the sample, and &#916;dsample is the peak distance of the Brillouin signal.</li>
	<li>Reconstruct the 2D Brillouin image based on the Brillouin shifts of all pixels. 
	NOTE: To conduct local analysis, one can select a region of interest (e.g., the neural plate) from the acquired Brillouin image and quantify its mechanical properties. A common approach is to calculate the average Brillouin shift of the selected region.</li>
</ol>

Longitudinal Monitoring of Neural Plate Mechanics in Chick Embryo Development

The authors declare that they have no conflict of interest.

The early development of the embryo can be easily affected by external disturbances. Therefore, utmost caution is required during the sample extraction and transfer. One potential issue is the detachment of the embryo from the filter paper, which can lead to the shrinking of the vitelline membrane and result in a tilted artifact of the neural plate in Brillouin imaging. Furthermore, this shrinking may halt the development of the embryo. Attention should be paid to several critical steps to prevent detachment. First, in s...

Neural tube defects (NTDs) are severe birth defects of the central nervous system caused by failures in neural tube closure (NTC) during embryonic development1. The etiology of NTDs is complex. Studies have shown that NTC involves a sequence of morphogenetic processes, including convergent extension, bending of the neural plate (e.g., apical constriction), elevating the neural fold, and finally adhesion of the neural fold. These processes are regulated by multiple molecular and genetic mechanisms2,3, and any malfunction in these processes may result in NTDs4,5,6. As mounting evidence suggests that mechanical cues also play crucial roles during NTC3,7,8,9,10,11, and relationships have been found between genes and mechanical cues12,13,14, it becomes imperative to investigate the tissue biomechanics during neurulation.
Several techniques have been developed for measuring the mechanical properties of embryonic tissues, including laser ablation (LA)15, tissue dissection and relaxation (TDR)16,17, micropipette aspiration (MA)18, Atomic Force Microscopy (AFM)-based nanoindentation19, microindenters (MI)&#160;and microplates (MP)20, micro rheology (MR) with optical/magnetic tweezers21,22,23, and droplet-based sensors24. Existing methods can measure mechanical properties at spatial resolutions ranging from subcellular to tissue scales. However, most of these methods are invasive because they require contact with the sample (e.g., MA, AFM, MI, and MP), external material injection (e.g., MR and droplet-based sensors), or tissue dissection (e.g., LA and TDR). As a result, it is challenging for existing methods to monitor the mechanical evolution of neural plate tissue in situ25. Recently, reverberant optical coherence elastography has shown promise for non-contact mechanical mapping with high spatial resolution26.
Confocal Brillouin microscopy is an emerging optical modality that enables non-contact quantification of tissue biomechanics with subcellular resolution27,28,29,30. Brillouin microscopy is based on the principle of spontaneous Brillouin light scattering, which is the interaction between the incident laser light and the acoustic wave induced by thermal fluctuations within the material. Consequently, the scattered light experiences a frequency shift, known as the Brillouin shift &#969;R, following the equation31:
<img alt="Equation 1" src="/files/ftp_upload/66117/66117eq01.jpg" style="margin: auto;" /> (1)
Here, <img alt="Equation 2" src="/files/ftp_upload/66117/66117eq02.jpg" style="margin: auto;" /> is the refractive index of the material,&#160;&#955; is the wavelength of the incident light, M&#39; is the longitudinal modulus, &#961; is the mass density, and &#952; is the angle between the incident light and the scattered light. For the same type of biological materials, the ratio of refractive index and density <img alt="Equation 3" src="/files/ftp_upload/66117/66117eq03.jpg" style="margin: auto;" /> is approximately constant28,32,33,34,35,36. Thus, the Brillouin shift can be directly used to estimate relative mechanical changes in physiological processes. The feasibility of Brillouin microscopy has been validated in various biological samples29,37,38. Recently, time-lapse mechanical imaging of a live chick embryo was demonstrated by combining a Brillouin microscope with an on-stage incubation system39. This protocol provides detailed descriptions of sample preparation, experiment implementation, and data post-processing and analysis. We hope this effort will facilitate the widespread adoption of non-contact Brillouin technology for studying biomechanical regulation in embryo development and birth defects.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>100 mm Petri dish&#160;</td>
			<td>Fisherbrand</td>
			<td>FB0875713</td>
			<td></td>
		</tr>
		<tr>
			<td>2D motorized stage&#160;</td>
			<td>Prior Scientific</td>
			<td>H117E2</td>
			<td></td>
		</tr>
		<tr>
			<td>35 mm Petri dish</td>
			<td>World Precision Instruments</td>
			<td>FD35-100</td>
			<td></td>
		</tr>
		<tr>
			<td>Brillouin Microscope with on-stage incubator</td>
			<td>N/A</td>
			<td>N/A</td>
			<td>This is a custom-built Brillouin Microscope system based on Ref. 30</td>
		</tr>
		<tr>
			<td>Chicken eggs</td>
			<td>University of Connecticut</td>
			<td>N/A</td>
			<td></td>
		</tr>
		<tr>
			<td>CMOS camera</td>
			<td>Thorlabs</td>
			<td>CS2100M-USB</td>
			<td></td>
		</tr>
		<tr>
			<td>EMCCD camera</td>
			<td>Andor</td>
			<td>iXon</td>
			<td></td>
		</tr>
		<tr>
			<td>Ethanol</td>
			<td>Decon Laboratories, Inc.</td>
			<td>#2701</td>
			<td></td>
		</tr>
		<tr>
			<td>Filter paper</td>
			<td>Whatman</td>
			<td>1004-070</td>
			<td></td>
		</tr>
		<tr>
			<td>Incubator for in ovo culture</td>
			<td>GQF Manufacturing Company Inc.&#160;</td>
			<td>GQF 1502&#160;</td>
			<td></td>
		</tr>
		<tr>
			<td>Ring</td>
			<td>Thorlabs</td>
			<td>SM1RR</td>
			<td></td>
		</tr>
		<tr>
			<td>Microscope body</td>
			<td>Olympus</td>
			<td>IX73</td>
			<td></td>
		</tr>
		<tr>
			<td>NaCl</td>
			<td>Sigma-Aldrich</td>
			<td>S9888</td>
			<td></td>
		</tr>
		<tr>
			<td>On-stage incubator</td>
			<td>Oko labs</td>
			<td>OKO-H301-PRIOR-H117</td>
			<td></td>
		</tr>
		<tr>
			<td>Parafilm</td>
			<td>Bemis</td>
			<td>PM-996</td>
			<td></td>
		</tr>
		<tr>
			<td>Penicillin-Streptomycin</td>
			<td>Gibco</td>
			<td>15070-063</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipettes</td>
			<td>Fisherbrand</td>
			<td>13-711-6M</td>
			<td></td>
		</tr>
		<tr>
			<td>Scissors</td>
			<td>Artman instruments</td>
			<td>N/A</td>
			<td>3pc Micro Scissors 5</td>
		</tr>
		<tr>
			<td>Syringe</td>
			<td>BD</td>
			<td>305482</td>
			<td></td>
		</tr>
		<tr>
			<td>Tissue paper</td>
			<td>Kimwipes</td>
			<td>N/A</td>
			<td></td>
		</tr>
		<tr>
			<td>Tube</td>
			<td>Corning</td>
			<td>430052</td>
			<td></td>
		</tr>
		<tr>
			<td>Tweezers</td>
			<td>DR Instruments</td>
			<td>N/A</td>
			<td>Microdissection Forceps Set&#160;</td>
		</tr>
	</tbody>
</table>

monitoring the mechanical evolution of tissue during neural tube closure of chick embryo

Neural tube closure (NTC) is a critical process during embryonic development. Failure in this process can lead to neural tube defects, causing congenital malformations or even mortality. NTC involves a series of mechanisms on genetic, molecular, and mechanical levels. While mechanical regulation has become an increasingly attractive topic in recent years, it remains largely unexplored due to the lack of suitable technology for conducting mechanical testing of 3D embryonic tissue in situ. In response, we have developed a protocol for quantifying the mechanical properties of chicken embryonic tissue in a non-contact and non-invasive manner. This is achieved by integrating a confocal Brillouin microscope with an on-stage incubation system. To probe tissue mechanics, a pre-cultured embryo is collected and transferred to an on-stage incubator for ex ovo culture. Simultaneously, the mechanical images of the neural plate tissue are acquired by the Brillouin microscope at different time points during development. This protocol includes detailed descriptions of sample preparation, the implementation of Brillouin microscopy experiments, and data post-processing and analysis. By following this protocol, researchers can study the mechanical evolution of embryonic tissue during development longitudinally.

Author Spotlight: Non-Contact Measurement of Tissue Mechanics in Live Chick Embryos Using Brillouin Microscopy

Monitoring the Mechanical Evolution of Tissue During Neural Tube Closure of Chick Embryo

The scope of this research is to develop a novel tool that can measure tissue mechanics of a live embryo. Using this tool, we want to understand how tissue mechanics evolves when the embryo is experiencing neuron tube closure. This can help us understand the mechanical regulations in embryonic development.To measure tissue stiffness, current methods such as atomic force microscopy, nanoidention, and micropipette aspiration need to contact sample physically and apply force to deform it. This is highly challenging for measuring tissue mechanics of live embryo in situ. Here, we employed an optical technology named Brillouin microscopy.Compared to other technologies, Brillouin microscopy only uses a focus beam to measure tissue mechanics. Thus, this is a non-contact and a noninvasive method and has some microspatial resolution. This allow us to capture time-lapse mechanical image of a live embryo in situ.In the future, we want to understand the role of tissue mechanics in embryonic development thoroughly. In specific, we want to study how genetic factors, biochemical signaling pathway, and tissue mechanics coordinate with each other in morphogenesis. This could provide us with new insight in the provision of birth disease such as neuron tube defects.

Figure 6 shows the schematic of the Brillouin microscope. The system employs a 660 nm laser as the light source. An isolator is placed right after the laser head to reject any back-reflected light, and a neutral density (ND) filter is used to adjust the laser power. A pair of lenses, L1 and L2, with focal lengths of f1 = 16 mm and f2 = 100 mm, respectively, are used to expand the laser beam. A half-wave plate (HWP) and a linear polarizer (Polarizer 1) are employed to adjust the power of the ...

Watch this Scientific Journal Video about Monitoring the Mechanical Evolution of Tissue During Neural Tube Closure of Chick Embryo at JoVE.com

This protocol was developed to longitudinally monitor the mechanical properties of neural plate tissue during chick embryo neurulation. It is based on the integration of a Brillouin microscope and an on-stage incubation system, enabling live mechanical imaging of neural plate tissue in ex ovo cultured chick embryos.

Neural tube closure (NTC) is a critical process during embryonic development. Failure in this process can lead to neural tube defects, causing congenital ...

monitoring-mechanical-evolution-tissue-during-neural-tube-closure

Research

JoVE Journal

Developmental Biology

Experimental Preparation and Ex Ovo Culture of Chicken Embryo for Brillouin Microscopy

To begin, cut the filter paper into a rectangular shape of approximately 17 by 20 millimeters and remove the four corners. Then, create approximately seven by 10 millimeters of hollow center in the filter paper. Attach a commercially available ring to a flexible film layer and create a hollow center in the flexible film layer.Place a prepared ring into a 35-millimeter Petri dish. After pre-culturing, retrieve the egg from the incubator, and place it on its long axis on the egg carton tray. Clean the entire surface of the eggshell with 70%ethanol, and allow it to rest for 15 minutes.Hold the egg on its short axis and crack it at the bottom. Open the egg over a clean 100-millimeter Petri dish to extract its contents. Using a pipette, transfer approximately 10 milliliters of the thin albumin into a 15-milliliter tube for ex ovo culture.Fill the center well of the culture dish with thin albumin. Using tissue paper, gently remove the thick albumin attached to the vitelline membrane of the embryo. Now, carefully affix the filter paper to the vitelline membrane, ensuring the body axis of the embryo aligns with the center rectangle on the filter paper.Cut the membrane surrounding the filter paper with scissors. Using tweezers, gently pull the isolated filter paper away from the yoke in an oblique direction. Flip the filter paper upside down to position the embryo with its dorsal side down.Carefully immerse the entire filter paper from one side of the long axis into the 100-millimeter Petri dish containing wash medium. Using a clean pipette, gently spray the wash medium parallel to the filter paper to remove any residual yolk. Next, carefully remove the filter paper from the wash medium, and use tissue paper to absorb any excess medium from the edges of the embryo.Place the filter paper with the embryo onto the culture dish, ensuring that the dorsal side of the embryo is facing downward. Transfer the culture dish to the onstage incubator for ex ovo culture. Fill the culture dishes with a warm wash medium.When the embryo reaches a desired developmental stage, transfer the filter paper with the embryo to the culture dish filled with a wash medium. Place the culture dish into the onstage incubator of the Brillouin microscope. For the calibration process, measure the Brillouin signal of water.Then, measure the Brillouin signal of methanol. Under bright-field imaging with a four times objective lens, adjust the laser illumination point to the second pair of somites. Then, switch to a 40 times objective lens and perform fine adjustment of the laser point to the middle of the neural tube.Unblock the laser beam and adjust the focal plane. Scan the embryo using a two-dimensional translational stage and acquire a Brillouin image of the region of interest. After completing the scan, carefully remove the filter paper with the embryo.Use tissue paper to absorb any excess wash medium from the embryo. Place the embryo back into the culture dish filled with thin albumin for continuous culturing. For Brillouin image reconstruction, load the water and methanol signal data.Click set region and select the region with four dots for calculating calibration parameters. Save the calibration results. Load the embryo scanning data, and click start for the processing of the parameters.Finally, reconstruct the 2-D Brillouin image based on the Brillouin shifts of all pixels. Brillouin shift in the estimated longitudinal modulus of the neural plate against somite number and incubation time showed an increase in Brillouin shift of the tissue during neural tube closure.

517 Views.  Wayne State University.  This protocol was developed to longitudinally monitor the mechanical properties of neural plate tissue during chick embryo neurulation. It is based on the integration of a Brillouin microscope and an on-stage incubation system, enabling live mechanical imaging of neural plate tissue in ex ovo cultured chick embryos.

Longitudinal Monitoring of Neural Plate Mechanics in Chick Embryo Development

概要