The authors thank W. Sun and K. Jansen for the critical discussions, and acknowledge support by the Nano Biomechanics Lab at the National University of Singapore. N.A.K. acknowledges support by a Marie Curie IIF Fellowship.

1. Cell Harvesting
<ol>
	<li>Obtain MD-MBA-231 cells from the 37 &#176;C, 5% CO2 incubator. Detach cells from tissue culture plate using 0.5% Trypsin-EDTA solution. Use 1 ml of Trypsin-EDTA solution for cell cultured in a T25 flask.</li>
	<li>Pellet cells in a 15 ml conical tube by centrifugation at 200 &#215; g for 4 min, aspirate the supernatant, and resuspend cells in 5 ml of culture media.</li>
	<li>Count cell density, &#961;, using a hemocytometer. 
	Note: To prepare the cell-seeded inner gel, the cell suspension will later on be diluted 10&#215; to reach the final cell seeding density. Therefore, 10&#215; concentrated cell suspension is required.</li>
	<li>Calculate the volume of medium required to achieve a 10&#215; cell concentration: 
	<img alt="Equation 1" fo:content-width="2in" src="/files/ftp_upload/52735/52735eq1.jpg" width="175" /> 
	Note: A final cell seeding density, cfinal, of around 2 &#215; 106 cells/ml is recommended for MD-MBA-231 cells and is used in this protocol. Other seeding densities can also be explored for other cell types.</li>
	<li>Pellet cells one more time in a 15 ml conical tube by centrifugation at 200 &#215; g for 4 min, and aspirate the supernatant.</li>
	<li>Resuspend the cells in the required amount (Vmedium calculated in step 1.3) of serum-free cell culture medium thoroughly to minimize cell clumping. 
	Note: Phenol red is auto-fluorescent, and can interfere with fluorescence/reflectance imaging. Use of phenol red-free medium may be considered to achieve best image quality.</li>
</ol>
2. Preparation of Collagen Solutions
<ol>
	<li>Obtain the stock collagen solution, 10&#215; PBS buffer, Milli-Q H2O, 0.1 M NaOH, and several microcentrifuge tubes. Keep all on ice to prevent premature collagen polymerization, and maintain sterile condition.</li>
	<li>Equilibrate a sterile glass-bottom dish by pre-warming it in the 37 &#176;C incubator. 
	Note: All volumes in this protocol have been optimized for a glass-bottom dish with 12 mm well. If other dish type is used, adjust the volumes correspondingly.</li>
	<li>Calculate the required volume needed to prepare 50 &#181;l of 2.4 mg/ml collagen solution for the inner gel (solution I) based on the collagen stock concentration. 
	Note: Other collagen concentrations for the inner gel can also be used.</li>
	<li>In a sterile environment (typically a biosafety hood), slowly add 5 &#181;l of 10&#215; PBS buffer to the required amount of collagen stock solution (calculated in step 2.3) with gentle swirling. Take care to avoid air bubble formation.</li>
	<li>Adjust the pH of the mixture to 7.4 using 0.1 M NaOH using calibrated pH-meter. As a rough guide, use about 5 &#181;l to bring the pH close to 7.4 (the amount varies depending on the stock concentration and pH). 
	Note: Note that the volumes involved in this step is too small for the use of standard pH meter. Use one of the following tricks:
	<ol>
		<li>Prepare collagen solutions for multiple samples. Adjust the pH in bulk using standard pH meter and distribute the collagen solutions across the samples.</li>
		<li>Alternatively, adjust the pH of a collagen solution in larger volume (i.e., volume that allow the use of standard pH meter). Note the amount of NaOH needed to bring the pH to the final pH. Scale down the volumes and use the appropriate amount of NaOH for the experiment. Confirm the pH value using Litmus paper.</li>
		<li>Otherwise, use a micro pH electrode to more accurately adjust the pH of small quantities.</li>
	</ol>
	</li>
	<li>Bring the solution to a volume of 45 &#181;l using H2O. Perform all steps on ice to prevent premature collagen polymerization.</li>
</ol>
3. Formation of Concentric Gel Culture
<ol>
	<li>Take the pre-warmed glass-bottom dish (see step 2.2) from the incubator.</li>
	<li>Add 5 &#181;l of the 10&#215; concentrated cell suspension (prepared in step 1.5) to solution I. Resuspend thoroughly. Take care to avoid air bubble formation. The mixture now has a volume of 50 &#181;l and contains the final collagen concentration (2.4 mg/ml) and cell density (cfinal = 2 &#215; 106 cells/ml).</li>
	<li>Add 20 &#181;l of the cell-containing solution I slowly to the center of the well, so that it forms a dome-shaped droplet (Figure 1A). Take care to avoid bubble formation at this step. If a bubble forms, carefully but quickly try to either rupture it or suck it out using a pipette tip. Gently place the dish back in the incubator to let the inner gel polymerize for 45 min.</li>
	<li>Prepare solution O (for the outer, acellular collagen gel) about 15 min before the end of this incubation step. 
	Note: The outer gel condition can be varied in terms of collagen concentration and polymerization pH to obtain networks with different microstructures10. In this protocol, focus on a 1.5 &#8211; 4.0 mg/ml collagen gel polymerized at a pH of 7.4.
	<ol>
		<li>Based on the collagen stock concentration, calculate the required volume needed to prepare 200 &#181;l of collagen solution O at the final concentration.</li>
	</ol>
	</li>
	<li>Add 20 &#181;l of 10&#215; PBS buffer slowly to the required amount of collagen stock solution (calculated in step 3.4) with gentle swirling. Adjust the pH of the mixture to the final pH using 0.1 M NaOH with the use of calibrated pH-meter. See note to step 2.5 regarding pH adjustment.</li>
	<li>Bring the solution to a final volume of 200 &#181;l using H2O. Perform all steps on ice to prevent premature collagen polymerization.</li>
	<li>Take the dish from the incubator after 45 min polymerization of the inner gel (see step 3.3). Gently add 180 &#181;l of solution O on top of the inner gel, so that the solution completely covers the inner gel and fills up the well (Figure 1B).
	<ol>
		<li>Perform this step carefully without stirring the solution, which can lead to non-uniform fiber orientations in the outer gel. Take care to avoid touching the inner gel with a pipette tip, and to avoid the formation of bubbles or air pockets. If a bubble forms, carefully but quickly try to either rupture it or suck it out using a pipette tip. Gently place the dish back in the incubator to let the outer gel polymerize.</li>
	</ol>
	</li>
	<li>Take the dish from the incubator after 45 min of polymerization. The gel should already be fairly solidified at this point, although it can still detach from the bottom surface if handled roughly.
	<ol>
		<li>Gently pour 2 ml of warmed cell culture medium to the dish (Figure 1C). Make sure that the gel is completely submerged in the medium. Refresh the medium every 2 &#8211; 3 days throughout the duration of culture.</li>
	</ol>
	</li>
</ol>
4. Live-cell Imaging
<ol>
	<li>Perform imaging using an inverted confocal microscope equipped with long-term live-cell imaging capability. Include a built-in incubation chamber with a temperature (37 &#176;C) and CO2 (5%) control. Switch on the microscope and warm up the stage at least 1 hr before starting the experiment. 
	Note: Use objective lens with long working distance to optimize the observation and localization of cells in the 3D gels.</li>
	<li>Incubate the gel in medium containing 5 &#181;l of fluorescent cell tracker dye for 30 min to allow accurate localization of the cells in the 3D system. Subsequently, remove unbound dye by washing three times with 1&#215; PBS. Afterwards, add cell culture medium to the dish.</li>
	<li>Take the dish from the incubator and place it on the microscope stage (Figure 1D). 
	Note: Live cell imaging can start in principle right after the polymerization of the outer gel. However at this point, the cells in the inner gel have not spread yet. To examine the migration of the first cells that have invaded the outer gel, live-cell imaging can start 24 hr (depending on the cell type) after the initiation of culture. As a rough guide, around 12 - 14 days of culture are needed for most of the cells in the inner gel to enter the outer gel.</li>
	<li>Select Volumes of View (VoV&#8217;s) in regions in the outer gel surrounding the inner gel. After 24 hr of incubation, the cell population will have spread, crossed the interface between the inner and outer gels, and started to invade the outer gel.
	<ol>
		<li>For the VoV&#8217;s, include the gel regions immediately next to the gel interface, intermediate regions, and regions close to the outskirt of the outer gel7. Exclude regions closer than 50 &#181;m from the bottom and side surfaces, as well as from the top of the gel, to avoid possible edge effects. Each VoV typically measures 647 &#215; 647 &#215; 100 &#181;m3 (in x, y, and z directions, respectively), with 5 &#181;m interval in the z-stack.</li>
	</ol>
	</li>
	<li>Ensure imaging modes, channels/filters, exposure times, and image resolutions are correctly selected. For label-free imaging of the collagen network, use confocal reflectance microscopy simultaneously during the time-lapse live-cell imaging.</li>
	<li>Take sample images, plot the intensity histograms, and adjust the gains and offsets to observe sufficient signal and avoid saturation by ensuring that the histogram lies between zero and the maximum intensity. Do not change these settings any more throughout the duration of the experiment.</li>
	<li>Take time-lapse images of the selected VoV&#8217;s, with a time interval, &#916;t, of 10 min for 8 hrs (or longer if necessary).</li>
</ol>
5. Cell Tracking and Data Analysis
<ol>
	<li>Carry out quantitative image post-processing from the z-stack images using appropriate image processing software.
	<ol>
		<li>Segment the time-lapse images to automatically select the 3D cell positions in (x,y,z,t).</li>
		<li>For every frame, manually check the localization accuracy and remove false positives due to cell debris and cellular protrusions that may have been mistaken for cells. Remove proliferative cells from the analysis and split overlapping or connected cells into distinct objects.</li>
	</ol>
	</li>
	<li>Generate 3D time-lapse cell tracks from the cell coordinates (x,y,z,t) obtained in the previous step by linking the location of each cell in the time sequence.</li>
	<li>Eliminate random and system noise by removing tracks shorter than a threshold track length (typically 20 min).</li>
	<li>Correct for sample drift by subtracting the overall net displacements from the tracks if necessary.</li>
	<li>Calculate cell displacement, <img alt="Equation 2" fo:content-width="0.8in" src="/files/ftp_upload/52735/52735eq2.jpg" width="80" />, and cell migration distance, <img alt="Equation 3" fo:content-width="1in" src="/files/ftp_upload/52735/52735eq3.jpg" width="100" />, from the observed cell trajectories, where is a vector representing the 3D location of a cell at time and is the total number of time points.
	<ol>
		<li>Calculate cell speed as S = d/(n &#8226; &#916;t), where &#916;t is the time interval between frames. Calculate cell migration directionality (or persistence) using P = &#916;d/d. This simple measure of persistence implies that for P = 0 the net displacement is zero and for P = 1 the trajectory is a straight directional line.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Horwitz, R., Webb, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cell+migration.">Cell migration.</a> Curr Biol. 13 (19), R756-R759 (2003).</li><li>Liang, C. C., Park, A. Y., Guan, J. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vitro+scratch+assay:+a+convenient+and+inexpensive+method+for+analysis+of+cell+migration+in+vitro.">In vitro scratch assay: a convenient and inexpensive method for analysis of cell migration in vitro.</a> Nat. Protoc. 2 (2), 329-333 (2007).</li><li>Provenzano, P. P., Eliceiri, K. W., Inman, D. R., Keely, P. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Engineering+three-dimensional+collagen+matrices+to+provide+contact+guidance+during+3D+cell+migration.">Engineering three-dimensional collagen matrices to provide contact guidance during 3D cell migration.</a> Curr. Prot. Cell Biol. 10, 10-17 (2010).</li><li>Friedl, P., Sahai, E., Weiss, S., Yamada, K. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=New+dimensions+in+cell+migration.">New dimensions in cell migration.</a> Nat. Rev. Mol. Cell Biol. 13 (11), 743-747 (2012).</li><li>Grinnell, F., Petroll, W. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cell+motility+and+mechanics+in+three-dimensional+collagen+matrices.">Cell motility and mechanics in three-dimensional collagen matrices.</a> Annu. Rev. Cell. Dev. Biol. 26, 335-361 (2010).</li><li>Wirtz, D., Konstantopoulos, K., Searson, P. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+physics+of+cancer:+the+role+of+physical+interactions+and+mechanical+forces+in+metastasis.">The physics of cancer: the role of physical interactions and mechanical forces in metastasis.</a> Nat. Rev. Cancer. 11 (7), 512-522 (2011).</li><li>Sun, W., Kurniawan, N. A., Kumar, A. P., Rajagopalan, R., Lim, C. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+migrating+cell-induced+matrix+reorganization+on+3D+cancer+cell+migration.">Effects of migrating cell-induced matrix reorganization on 3D cancer cell migration.</a> Cell. Mol. Bioeng. 7 (2), 205-217 (2014).</li><li>Achilli, M., Mantovani, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tailoring+mechanical+properties+of+collagen-based+scaffolds+for+vascular+tissue+engineering:+the+effects+of+pH,+temperature+and+ionic+strength+on+gelation.">Tailoring mechanical properties of collagen-based scaffolds for vascular tissue engineering: the effects of pH, temperature and ionic strength on gelation.</a> Polymers. 2 (4), 664-680 (2010).</li><li>Kurniawan, N. A., Wong, L. H., Rajagopalan, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Early+stiffening+and+softening+of+collagen:+interplay+of+deformation+mechanisms+in+biopolymer+networks.">Early stiffening and softening of collagen: interplay of deformation mechanisms in biopolymer networks.</a> Biomacromolecules. 13 (3), 691-698 (2012).</li><li>Sun, W., Lim, C. T., Kurniawan, N. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanistic+adaptability+of+cancer+cells+strongly+affects+anti-migratory+drug+efficacy.">Mechanistic adaptability of cancer cells strongly affects anti-migratory drug efficacy.</a> J. R. Soc. Interface. 11 (99), 20140638 (2014).</li><li>Guzman, A., Ziperstein, M. J., Kaufman, L. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effect+of+fibrillar+matrix+architecture+on+tumor+cell+invasion+of+physically+challenging+environments.">The effect of fibrillar matrix architecture on tumor cell invasion of physically challenging environments.</a> Biomaterials. 35 (25), 6954-6963 (2014).</li><li>Wolf, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Physical+limits+of+cell+migration:+control+by+ECM+space+and+nuclear+deformation+and+tuning+by+proteolysis+and+traction+force.">Physical limits of cell migration: control by ECM space and nuclear deformation and tuning by proteolysis and traction force.</a> J. Cell Biol. 201 (7), 1069-1084 (2013).</li><li>Friedl, P., Gilmour, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Collective+cell+migration+in+morphogenesis,+regeneration+and+cancer.">Collective cell migration in morphogenesis, regeneration and cancer.</a> Nat. Rev. Mol. Cell Biol. 10 (7), 445-457 (2009).</li><li>Vedula, S. R. K., Ravasio, A., Lim, C. T., Ladoux, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Collective+cell+migration:+a+mechanistic+perspective.">Collective cell migration: a mechanistic perspective.</a> Physiology. 28 (6), 370-379 (2013).</li><li>Petrie, R. J., Doyle, A. D., Yamada, K. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Random+versus+directionally+persistent+cell+migration.">Random versus directionally persistent cell migration.</a> Nat. Rev. Mol. Cell Biol. 10 (8), 538-549 (2009).</li><li>Miron-Mendoza, M., Seemann, J., Grinnell, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+differential+regulation+of+cell+motile+activity+through+matrix+stiffness+and+porosity+in+three+dimensional+collagen+matrices.">The differential regulation of cell motile activity through matrix stiffness and porosity in three dimensional collagen matrices.</a> Biomaterials. 31 (25), 6425-6435 (2010).</li><li>Mouw, J. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tissue+mechanics+modulate+microRNA-dependent+PTEN+expression+to+regulate+malignant+progression.">Tissue mechanics modulate microRNA-dependent PTEN expression to regulate malignant progression.</a> Nat. Med. 20 (4), 360-367 (2014).</li><li>Wolf, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Collagen-based+cell+migration+models+in+vitro+and+in+vivo.">Collagen-based cell migration models in vitro and in vivo.</a> Semin. Cell Dev. Biol. 20 (8), 931-941 (2009).</li><li>Wong, L. H., Kurniawan, N. A., Too, H. -. P., Rajagopalan, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Spatially+resolved+microrheology+of+heterogeneous+biopolymer+hydrogels+using+covalently+bound+microspheres.">Spatially resolved microrheology of heterogeneous biopolymer hydrogels using covalently bound microspheres.</a> Biomech. Model. Mechanobiol. 13 (4), 839-849 (2014).</li><li>Gupton, S. L., Waterman-Storer, C. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Spatiotemporal+feedback+between+actomyosin+and+focal-adhesion+systems+optimizes+rapid+cell+migration.">Spatiotemporal feedback between actomyosin and focal-adhesion systems optimizes rapid cell migration.</a> Cell. 125 (7), 1361-1374 (2006).</li><li>Provenzano, P. P., Inman, D. R., Eliceiri, K. W., Trier, S. M., Keely, P. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Contact+guidance+mediated+three-dimensional+cell+migration+is+regulated+by+Rho/ROCK-dependent+matrix+reorganization.">Contact guidance mediated three-dimensional cell migration is regulated by Rho/ROCK-dependent matrix reorganization.</a> Biophys. J. 95 (11), 5374-5384 (2008).</li><li>Wolf, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multi-step+pericellular+proteolysis+controls+the+transition+from+individual+to+collective+cancer+cell+invasion.">Multi-step pericellular proteolysis controls the transition from individual to collective cancer cell invasion.</a> Nat. Cell Biol. 9 (8), 893-904 (2007).</li><li>Jansen, K. A., Bacabac, R. G., Piechocka, I. K., Koenderink, G. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cells+actively+stiffen+fibrin+networks+by+generating+contractile+stress.">Cells actively stiffen fibrin networks by generating contractile stress.</a> Biophys. J. 105 (10), 2240-2251 (2013).</li></ol>

The authors have nothing to disclose.

In this protocol we describe an in vitro assay to study the 3D migrational behavior of cells in matrix environments that topologically resemble ECMs encountered in vivo. There are three main strengths of this assay as compared to other currently available methods. First, this assay allows one to simultaneously examine the cell migration mechanisms at both population level and individual cell level. This opens up possibilities of studying collective cell migration13, which has to date been lar...

Migration of cells plays a key role in various physiological responses such as embryonic development, haemostasis, and immune response as well as in pathological processes such as vascular diseases, inflammation, and cancer1. Dissecting the biochemical and biophysical factors underlying cell migration is therefore fundamentally important not only to understand the basic principles of cellular functions, but also to advance various biomedical applications, such as in tissue engineering, anti-metastasis and anti-inflammatory drug development. Since in vivo observation is technically challenging, a lot of efforts has been focused on in vitro recapitulation of cell migration.
In vitro methods to study cell migration have largely been designed for assays on two dimensional (2D) surfaces, most notably the scratch or wound healing assay2. Such assays offer simple experimental setup, easy live-cell imaging, and provide useful insights into various biochemical mechanisms underlying cell migration. However, these assays do not account for extracellular matrix (ECM) architecture and remodeling, which are critical aspects in understanding in vivo migration. Recently, it has been increasingly appreciated that a 3D culture model, often in collagen-based matrices3, provides a platform that better resembles the in vivo situation. Indeed, cells exhibit migrational dynamics that are distinct from those on 2D surfaces, especially due to the different dimensionality of the environment4. Moreover, the biophysical and mechanical properties of the matrix sensitively affect cell migration5, including in the context of tumor cell invasion6.
Here, we present a method to study 3D cell migration behavior in ECM with biophysical properties that can be easily varied with preparation conditions. The cells are seeded in an &#8220;inner gel&#8221; and are allowed to escape into and invade the initially acellular &#8220;outer gel&#8221;. The method relies on the cell&#8217;s ability to recognize the presence of, and propensity to migrate into, cell-free regions in the outer gel, which is closely linked to cell mechanosensing7. In this study, we employ collagen networks as the ECMs invaded by highly invasive breast cancer cells, MD-MBA-231. The mechanical properties and microstructure of both the inner and outer gels can be tuned8 and characterized9 to achieve physiologically relevant conditions. Reconstruction and analysis of the cell tracks allow detailed quantitative examination of the spatiotemporal migration behavior at both population level and individual cell level. Importantly, the setup of the concentric gel system mimics the in vivo tissue topology faced by migrating cells, especially invading cancer cells, thus offering important insights into the physical mechanisms of cell migration and metastasis.

<table><tbody><tr><td>Cell culture incubator</td><td>Fisher Scientific Pte Ltd</td><td>Model: 371, S/No 318854-6055</td><td></td></tr><tr><td>Confocal microscope</td><td>Nikon A1R</td><td></td><td>Inverted confocal laser scanning microscope equipped with incubator chamber</td></tr><tr><td>Dulbecco&#039;s Modified Eagle&#039;s Medium (DMEM)</td><td>Life Technologies</td><td>11965-092</td><td></td></tr><tr><td>Fetal Bovine Serum (FBS)</td><td>Life Technologies</td><td>10082-147</td><td></td></tr><tr><td>Fluorescent CellTracker dye CMTMR</td><td>Life Technologies</td><td>C2927</td><td></td></tr><tr><td>Glass-bottom dish</td><td>IWAKI Cell Biology</td><td>3931-035</td><td>35 mm diameter dish with 12 mm diameter glass-bottom well</td></tr><tr><td>Hemocytometer</td><td>iN CYTO</td><td>DHC-N01 (Neubauer Improved)</td><td></td></tr><tr><td>Microprocessor pH meter</td><td>Hanna Instruments</td><td>pH 211</td><td></td></tr><tr><td>Nutragen Collagen</td><td>Advanced BioMatrix</td><td>#5010-D</td><td>Acid-solubilized bovine collagen type I (stock pH ~ 2)</td></tr><tr><td>Objective lens</td><td>Nikon</td><td></td><td>CFI Super Plan Fluor ELWD ADM 20XC, W.D. 8.2-6.9mm, NA 0.45.</td></tr><tr><td>Penicillin-Streptomycin</td><td>Life Technologies</td><td>15140-122</td><td></td></tr><tr><td>pH meter</td><td>Sartorius</td><td>S/No 29153352</td><td>Basic pH Meter PB-11</td></tr><tr><td>Trypsin-EDTA</td><td>Life Technologies</td><td>15400-054</td><td></td></tr></tbody></table>

concentric gel system to study the biophysical role of matrix microenvironment on 3d cell migration

The ability of cells to migrate is crucial in a wide variety of cell functions throughout life&#160;from embryonic development and wound healing&#160;to tumor and cancer metastasis. Despite intense research efforts, the basic biochemical and biophysical principles of cell migration are still not fully understood, especially in the physiologically relevant three-dimensional (3D) microenvironments. Here, we describe an in vitro assay designed to allow quantitative examination of 3D cell migration behaviors. The method exploits the cell&#8217;s mechanosensing ability and propensity to migrate into previously unoccupied extracellular matrix (ECM). We use the invasion of highly invasive breast cancer cells, MDA-MB-231, in collagen gels as a model system. The spread of cell population and the migration dynamics of individual cells over weeks of culture can be monitored using live-cell imaging and analyzed to extract spatiotemporally-resolved data. Furthermore, the method is easily adaptable for diverse extracellular matrices, thus offering a simple yet powerful way to investigate the role of biophysical factors in the microenvironment on cell migration.

The concentric gel assay presented here was performed using highly invasive breast cancer cells, MDA-MB-231, with 2.4 mg/ml inner collagen gel and a cell seeding density of = 2 &#215; 106 cells/ml, as an example. As shown in Figure 2, typically after a few days of culture, the cells breached the inner&#8211;outer gel interface and started to invade the outer gel. The cell population spread predominantly radially outwards.
The polymerization conditions of the outer g...

Watch this Scientific Journal Video about Concentric Gel System to Study the Biophysical Role of Matrix Microenvironment on 3D Cell Migration at JoVE.com

Concentric Gel System to Study the Biophysical Role of Matrix Microenvironment on 3D Cell Migration

The mechanical properties and microstructure of the extracellular matrix strongly affect 3D migration of cells. An in vitro method to study the spatiotemporal cell migration behavior in biophysically variable environments, at both population and individual cell levels, is described.

The ability of cells to migrate is crucial in a wide variety of cell functions throughout life&#160;from embryonic development and wound healing&#160;to ...

concentric-gel-system-to-study-biophysical-role-matrix

Research

JoVE Journal

Bioengineering

8.5K Views.  FOM Institute AMOLF.  De mechanische eigenschappen en de microstructuur van de extracellulaire matrix sterk beïnvloeden 3D migratie van cellen. Een in vitro werkwijze om de tijdruimtelijk celmigratie gedrag biofysisch variabele omgevingen zowel bevolking en afzonderlijke cel niveaus, gaande beschreven. 

Video: Concentric Gel System to Study the Biophysical Role of Matrix Microenvironment on 3D Cell Migration

Live-cell Imaging of Migrating Cells Expressing Fluorescently-tagged Proteins in a Three-dimensional Matrix

Traditionally, cell migration has been studied on two-dimensional, stiff plastic surfaces. However, during important biological processes such as wound healing, tissue regeneration, and cancer metastasis, cells must navigate through complex, three-dimensional extracellular tissue. To better understand the mechanisms behind these biological processes, it is important to examine the roles of the proteins responsible for driving cell migration. Here, we outline a protocol to study the mechanisms of cell migration using the epithelial cell line (MDCK), and a three-dimensional, fibrous, self-polymerizing matrix as a model system. This optically clear extracellular matrix is easily amenable to live-cell imaging studies and better mimics the physiological, soft tissue environment. This report demonstrates a technique for directly visualizing protein localization and dynamics, and deformation of the surrounding three-dimensional matrix. 
Examination of protein localization and dynamics during cellular processes provides key insight into protein functions. Genetically encoded fluorescent tags provide a unique method for observing protein localization and dynamics. Using this technique, we can analyze the subcellular accumulation of key, force-generating cytoskeletal components in real-time as the cell maneuvers through the matrix. In addition, using multiple fluorescent tags with different wavelengths, we can examine the localization of multiple proteins simultaneously, thus allowing us to test, for example, whether different proteins have similar or divergent roles. Furthermore, the dynamics of fluorescently tagged proteins can be quantified using Fluorescent Recovery After Photobleaching (FRAP) analysis. This measurement assays the protein mobility and how stably bound the proteins are to the cytoskeletal network.
By combining live-cell imaging with the treatment of protein function inhibitors, we can examine in real-time the changes in the distribution of proteins and morphology of migrating cells. Furthermore, we also combine live-cell imaging with the use of fluorescent tracer particles embedded within the matrix to visualize the matrix deformation during cell migration. Thus, we can visualize how a migrating cell distributes force-generating proteins, and where the traction forces are exerted to the surrounding matrix. Through these techniques, we can gain valuable insight into the roles of specific proteins and their contributions to the mechanisms of cell migration.

Cellular processes such as cell migration have traditionally been studied on two-dimensional, stiff plastic surfaces. This report describes a technique for directly visualizing protein localization and analyzing protein dynamics in cells migrating in a more physiologically relevant, three-dimensional matrix.

Traditionally, cell migration has been studied on two-dimensional, stiff plastic surfaces. However, during important biological processes such as wound ...

Creating Adhesive and Soluble Gradients for Imaging Cell Migration with Fluorescence Microscopy

Cells can sense and migrate towards higher concentrations of adhesive cues such as the glycoproteins of the extracellular matrix and soluble cues such as growth factors. Here, we outline a method to create opposing gradients of adhesive and soluble cues in a microfluidic chamber, which is compatible with live cell imaging. A copolymer of poly-L-lysine and polyethylene glycol (PLL-PEG) is employed to passivate glass coverslips and prevent non-specific adsorption of biomolecules and cells. Next, microcontact printing or dip pen lithography are used to create tracks of streptavidin on the passivated surfaces to serve as anchoring points for the biotinylated peptide arginine-glycine-aspartic acid (RGD) as the adhesive cue. A microfluidic device is placed onto the modified surface and used to create the gradient of adhesive cues (100% RGD to 0% RGD) on the streptavidin tracks. Finally, the same microfluidic device is used to create a gradient of a chemoattractant such as fetal bovine serum (FBS), as the soluble cue in the opposite direction of the gradient of adhesive cues.

A method for the assembly of adhesive and soluble gradients in a microscopy chamber for live cell migration studies is described. The engineered environment combines antifouling surfaces and adhesive tracks with solution gradients and therefore allows one to determine the relative importance of guidance cues.

Cells can sense and migrate towards higher concentrations of adhesive cues such as the glycoproteins of the extracellular matrix and soluble cues such as ...

Study of Cell Migration in Microfabricated Channels

The method described here allows the study of cell migration under confinement in one dimension. It is based on the use of microfabricated channels, which impose a polarized phenotype to cells by physical constraints. Once inside channels, cells have only two possibilities: move forward or backward. This simplified migration in which directionality is restricted facilitates the automatic tracking of cells and the extraction of quantitative parameters to describe cell movement. These parameters include cell velocity, changes in direction, and pauses during motion. Microchannels are also compatible with the use of fluorescent markers and are therefore suitable to study localization of intracellular organelles and structures during cell migration at high resolution. Finally, the surface of the channels can be functionalized with different substrates, allowing the control of the adhesive properties of the channels or the study of haptotaxis. In summary, the system here described is intended to analyze the migration of large cell numbers in conditions in which both the geometry and the biochemical nature of the environment are controlled, facilitating the normalization and reproducibility of independent experiments.

A quantitative method to study spontaneous migration of cells in a one-dimensional confined microenvironment is described. This method takes advantage of microfabricated channels and can be used to study migration of large number of cells under different conditions in single experiments.

The method described here allows the study of cell migration under confinement in one dimension. It is based on the use of microfabricated channels, which ...

Analysis of Cell Migration within a Three-dimensional Collagen Matrix

The ability to migrate is a hallmark of various cell types and plays a crucial role in several physiological processes, including&#160;embryonic development, wound healing, and immune responses. However, cell migration is also a key mechanism in cancer enabling these cancer cells to detach from the primary tumor to start metastatic spreading. Within the past years various cell migration assays have been developed to analyze the migratory behavior of different cell types. Because the locomotory behavior of cells markedly differs between a two-dimensional (2D) and three-dimensional (3D) environment it can be assumed that the analysis of the migration of cells that are embedded within a 3D environment would yield in more significant cell migration data. The advantage of the described 3D collagen matrix migration assay is that cells are embedded within a physiological 3D network of collagen fibers representing the major component of the extracellular matrix. Due to time-lapse video microscopy real cell migration is measured allowing the determination of several migration parameters as well as their alterations in response to pro-migratory factors or inhibitors. Various cell types could be analyzed using this technique, including lymphocytes/leukocytes, stem cells, and tumor cells. Likewise, also cell clusters or spheroids could be embedded within the collagen matrix concomitant with analysis of the emigration of single cells from the cell cluster/ spheroid into the collagen lattice. We conclude that the 3D collagen matrix migration assay is a versatile method to analyze the migration of cells within a physiological-like 3D environment.

Cell migration is a biological phenomenon that is involved in a plethora of physiological, such as wound healing and immune responses, and pathophysiological processes, like cancer. The 3D-collagen matrix migration assay is a versatile tool to analyze the migratory properties of different cell types within in a 3D physiological-like environment.

The ability to migrate is a hallmark of various cell types and plays a crucial role in several physiological processes, including&#160;embryonic ...

Revealing the Cytoskeletal Organization of Invasive Cancer Cells in 3D

Cell migration has traditionally been studied in 2D substrates. However, it has become increasingly evident that there is a need to study cell migration in more appropriate 3D environments, which better resemble the dimensionality of the physiological processes in question. Migratory cells can substantially differ in their morphology and mode of migration depending on whether they are moving on 2D or 3D substrates. Due to technical difficulties and incompatibilities with most standard protocols, structural and functional analysis of cells embedded within 3D matrices still remains uncommon. This article describes methods for preparation and imaging of 3D cancer cell cultures, either as single cells or spheroids. As an appropriate ECM substrate for cancer cell migration, we use nonpepsinized rat tail collagen I polymerized at room-temperature and fluorescently labeled to facilitate visualization using standard confocal microscopes. This work also includes a protocol for 3D immunofluorescent labeling of endogenous cell cytoskeleton. Using these protocols we hope to contribute to a better description of the molecular composition, localization, and functions of cellular structures in 3D.

This article presents a method to fluorescently label collagen that can be further used for both fix and live imaging of 3D cell cultures. We also provide an optimized protocol to visualize endogenous cytoskeletal proteins of cells cultured in 3D environments.

Cell migration has traditionally been studied in 2D substrates. However, it has become increasingly evident that there is a need to study cell migration ...

Medicine

Planar Gradient Diffusion System to Investigate Chemotaxis in a 3D Collagen Matrix

The importance of cell migration can be seen through the development of human life. When cells migrate, they generate forces and transfer these forces to their surrounding area, leading to cell movement and migration. In order to understand the mechanisms that can alter and/or affect cell migration, one can study these forces. In theory, understanding the fundamental mechanisms and forces underlying cell migration holds the promise of effective approaches for treating diseases and promoting cellular transplantation. Unfortunately, modern chemotaxis chambers that have been developed are usually restricted to two dimensions (2D) and have complex diffusion gradients that make the experiment difficult to interpret. To this end, we have developed, and describe in this paper, a direct-viewing chamber for chemotaxis studies, which allows one to overcome modern chemotaxis chamber obstacles able to measure cell forces and specific concentration within the chamber in a 3D environment to study cell 3D migration. More compelling, this approach allows one to successfully model diffusion through 3D collagen matrices and calculate the coefficient of diffusion of a chemoattractant through multiple different concentrations of collagen, while keeping the system simple and user friendly for traction force microscopy (TFM) and digital volume correlation (DVC) analysis.

Cell migration is an important part of human development and life. In order to understand the mechanisms that can alter cell migration, we present a planar gradient diffusion system to investigate chemotaxis in a 3D collagen matrix, which allows one to overcome modern diffusion chamber limitations of existing assays.

The importance of cell migration can be seen through the development of human life. When cells migrate, they generate forces and transfer these forces to ...

Sandwich-like Microenvironments to Harness Cell/Material Interactions

Cell culture has been traditionally carried out on bi-dimensional (2D) substrates where cells adhere using ventral receptors to the biomaterial surface. However in vivo, most of the cells are completely surrounded by the extracellular matrix (ECM), resulting in a three-dimensional (3D) distribution of receptors. This may trigger differences in the outside-in signaling pathways and thus in cell behavior.
This article shows that stimulating the dorsal receptors of cells already adhered to a 2D substrate by overlaying a film of a new material (a sandwich-like culture) triggers important changes with respect to standard 2D cultures. Furthermore, the simultaneous excitation of ventral and dorsal receptors shifts cell behavior closer to that found in 3D environments. Additionally, due to the nature of the system, a sandwich-like culture is a versatile tool that allows the study of different parameters in cell/material interactions, e.g., topography, stiffness and different protein coatings at both the ventral and dorsal sides. Finally, since sandwich-like cultures are based on 2D substrates, several analysis procedures already developed for standard 2D cultures can be used normally, overcoming more complex procedures needed for 3D systems.

The following protocol describes the procedure to assemble sandwich-like cultures to be used as an intermediate stage between bi-dimensional (2D) and three-dimensional (3D) cellular environments. The engineered systems can have applications in microscopy, biomechanics, biochemistry and cell biology assays.

Cell culture has been traditionally carried out on bi-dimensional (2D) substrates where cells adhere using ventral receptors to the biomaterial surface. ...

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo

Historically, most cellular processes have been studied in only 2 dimensions. While these studies have been informative about general cell signaling mechanisms, they neglect important cellular cues received from the structural and mechanical properties of the local microenvironment and extracellular matrix (ECM). To understand how cells interact within a physiological ECM, it is important to study them in the context of 3 dimensional assays. Cell migration, cell differentiation, and cell proliferation are only a few processes that have been shown to be impacted by local changes in the mechanical properties of a 3-dimensional ECM. Collagen I, a core fibrillar component of the ECM, is more than a simple structural element of a tissue. Under normal conditions, mechanical cues from the collagen network direct morphogenesis and maintain cellular structures. In diseased microenvironments, such as the tumor microenvironment, the collagen network is often dramatically remodeled, demonstrating altered composition, enhanced deposition and altered fiber organization. In breast cancer, the degree of fiber alignment is important, as an increase in aligned fibers perpendicular to the tumor boundary has been correlated to poorer patient prognosis1. Aligned collagen matrices result in increased dissemination of tumor cells via persistent migration2,3. The following is a simple protocol for embedding cells within a 3-dimensional, fibrillar collagen hydrogel. This protocol is readily adaptable to many platforms, and can reproducibly generate both aligned and random collagen matrices for investigation of cell migration, cell division, and other cellular processes in a tunable, 3-dimensional, physiological microenvironment.

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo

Collagen is a core component of the ECM, and provides essential cues for several cellular processes ranging from migration to differentiation and proliferation. Provided here is a protocol for embedding cells within 3D collagen hydrogels, and a more advanced technique for generating randomized or aligned collagen matrices using PDMS microchannels.

Historically, most cellular processes have been studied in only 2 dimensions.  While these studies have been informative about general cell signaling ...

Characterizing Cell Migration Within Three-dimensional In Vitro Wound Environments

Currently, most in vitro models of wound healing, such as well-established scratch assays, involve studying cell migration and wound closure on two-dimensional surfaces. However, the physiological environment in which in vivo wound healing takes place is three-dimensional rather than two-dimensional. It is becoming increasingly clear that cell behavior differs greatly in two-dimensional vs. three-dimensional environments; therefore, there is a need for more physiologically relevant in vitro models for studying cell migration behaviors in wound closure. The method described herein allows for the study of cell migration in a three-dimensional model that better reflects physiological conditions than previously established two-dimensional scratch assays. The purpose of this model is to evaluate cell outgrowth via the examination of cell migration away from a spheroid body embedded within a fibrin matrix in the presence of pro- or anti-migratory factors. Using this method, cell outgrowth from the spheroid body in a three-dimensional matrix can be observed and is easily quantifiable over time via brightfield microscopy and analysis of spheroid body area. The effect of pro-migratory and/or inhibitory factors on cell migration can also be evaluated in this system. This method provides researchers with a simple method of analyzing cell migration in three-dimensional wound associated matrices in vitro, thus increasing the relevance of in vitro cell studies prior to the use of in vivo animal models.

Characterizing Cell Migration Within Three-dimensional In Vitro Wound Environments

The goal of this protocol is to evaluate the effect of pro- and anti-migratory factors on cell migration within a three-dimensional fibrin matrix.

Currently, most in vitro models of wound healing, such as well-established scratch assays, involve studying cell migration and wound closure on ...

Quantifying Three-Dimensional Cell Migration Within and Into Granular Hydrogel Biomaterials

Granular hydrogel scaffolds hold significant potential in regenerative medicine, functioning either as carriers for cell delivery or as interfaces for tissue integration. This article introduces two novel approaches for quantifying cell migration within and into granular hydrogels, highlighting the distinct applications of these scaffolds. First, a cell monolayer interface assay that simulates tissue growth into granular hydrogels for integration purposes is presented. Second, a spheroid-based assay is described, designed to track cell movement within the hydrogel matrix, specifically suited for applications involving cell delivery. Both methods enable precise and controlled measurements of cell migration, providing a comprehensive toolkit for researchers utilizing granular hydrogel scaffolds. The motivation for these methods stems from the need for tailored control over cell migration within the scaffold to align with specific applications. By optimizing and standardizing these quantification techniques, researchers can iteratively refine granular hydrogel properties, ensuring their effectiveness in diverse regenerative medicine contexts. This robust set of quantitative tools offers new opportunities to enhance granular hydrogel scaffolds, advancing their use in both cell delivery and tissue integration applications.

A protocol for the quantitative evaluation of 3D cell migration within and into the interface of granular hydrogels is presented here.

Granular hydrogel scaffolds hold significant potential in regenerative medicine, functioning either as carriers for cell delivery or as interfaces for ...

Concentric Gel System to Study the Biophysical Role of Matrix Microenvironment on 3D Cell Migration

Samenvatting

Meer video's verkennen

Hoofdstukken in deze video