LH was funded by NPL&#39;s MedAccel program financed by the Department for Business, Energy and Industrial Strategy&#39;s Industrial Strategy Challenge Fund. JMG received funding from the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) under project GR 5824/1. JJ acknowledges the funding support from Academy of Medical Sciences Springboard (REF: SBF007\100007) award. SEB acknowledges support from Cancer Research UK under grant number C9545/A29580. AMI, BZ, and SR were supported by U.K. Department for Business, Energy &#38; Industrial Strategy via funding of the National Measurement System. Figure 1 and Figure 2 were created with BioRender.

Table 1: Overview of acoustic and optical properties found in soft tissues. Optical properties cover a spectrum ranging from 600 to 900 nm. It should be noted that these are only representative values intended to provide general guidance. Precise values may vary depending on the experimental condition (e.g., temperature) and frequency/wavelength. The literature provides more specific values. *No specific reference found. <a href="https://www.jove.com/files/ftp_upload/65475/65475_Table 1_rev.xlsx" target="_blank">Please click here to download this Table.</a>
The given protocol has been developed for making ~120 mL of phantom material. The masses of the components can be scaled to make different volumes of phantom material. Please note that for larger volumes (&#62;500 mL), the proposed equipment may not be able to sufficiently heat the phantom mixture homogenously. For this purpose, heating equipment should be adapted appropriately.
CAUTION: Always ensure suitable personal protective equipment (PPE) is worn throughout the entire fabrication process. This may include the use of lab coats, safety goggles, and safety gloves; refer and adhere to local safety guidelines. The procedure is adapted from Hacker et al.39; a summary of the steps is displayed in Figure 1.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/65475/65475fig01.jpg" /> 
Figure 1: Fabrication of the copolymer-in-oil material. (1) Materials for optical scattering and absorption are added to mineral oil and (2) sonicated at 90 &#176;C until dissolved. (3) Polymer(s) and stabilizer are added, and (4) the mixture is heated up in an oil bath to 160 &#176;C under low stirring. (5) Upon dissolution of all the components, the sample is poured into a suitable phantom mold and (6) left to harden at room temperature. This figure is reproduced from Hacker et al.39. <a href="https://www.jove.com/files/ftp_upload/65475/65475fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
1. Preparation of the mixture
<ol>
	<li>Prepare the Nigrosin stock solution by adding 0.4 g of Nigrosin to 40 mL of mineral oil. Ensure homogeneous mixing by sonication and thorough vortexing of the sample. Store the stock solution at room temperature. 
	NOTE: The stock solution should always be thoroughly mixed before reuse. If a phantom material without an optical scatterer (TiO2) or absorber (dye) is preferred, step 1 and 2&#160;can be skipped. Proceed with step 3.</li>
	<li>Sonicate 0.15 g of TiO2 and 1 mL of the dye stock solution in 100 mL (83.8 g) of mineral oil until all the components have been completely dissolved (~60 min) (Figure 1: steps 1 and 2). Set the sonicator to elevated temperatures (90 &#176;C) if the equipment allows, as this facilitates the mixing process. Proceed with steps 3-5 during the sonication time. 
	NOTE: If a phantom with higher absorbing and scattering properties is preferred, the sonication time may need to be extended.</li>
	<li>Weigh out the polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) and low-density polyethylene (LDPE) at the desired concentrations (e.g., SEBS = 25.14 g; LDPE = 6.70 g) (Figure 1: step 3).
	<ol>
		<li>Optional: An antioxidant may be added to increase stability, but it is not obligatory if the heating temperatures do not exceed 180&#176;C. 
		NOTE: In case solubility or viscosity issues are encountered at a later stage of the manufacturing process, it is advisable to exclude the LDPE. LDPE is incorporated to enhance the speed of sound in the material (Table 3); however, it is not mandatory for creating a stable phantom. By omitting LDPE, the manufacturing and molding process can be simplified, but it will result in a decrease in the subsequent speed of sound of the final material (Table 3).</li>
	</ol>
	</li>
	<li>Create an oil bath using suitable glassware and silicone oil; carefully secure it on the hotplate. Ensure the thermocouple remains in the silicone oil bath and does not touch the edges of the glassware throughout the procedure (Figure 2). 
	NOTE: Ensure that the thermoregulatory accessory is carefully mounted, as instructed by the equipment manufacturer.</li>
	<li>Place a magnetic stir bar of adequate length inside the oil bath to ensure uniform heat distribution.</li>
	<li>Turn on the hotplate, set the heating temperature to 160 &#176;C, and set the revolutions per minute (rpm) of the stirrer to 50.</li>
	<li>Transfer the LDPE and SEBS into the glass beaker containing the sonicated mineral oil (with TiO2 and Nigrosin). Introduce a magnetic stir bar of adequate length into the glass beaker and transfer it into the center of the oil bath for heating of the measured components. Ensure that the oil level in the bath remains above the mineral oil level inside the beaker (Figure 1: step 4).</li>
</ol>
2. Heating the mixture
<ol>
	<li>If at any stage the added polymer appears to float over the mineral oil, manually stir the mineral oil solution using a metallic spatula, so that any floating polymer is distributed inside the mineral oil. Wear heat-resistant gloves.</li>
	<li>Leave the mixture at 160 &#176;C until all the polymer has dissolved and the solution appears uniformly mixed, with a smooth and homogeneous texture (~1.5 h).</li>
</ol>
3. Vacuuming
NOTE: For removal of air bubbles, follow the following steps, depending on the equipment available.
<ol>
	<li>Place the hot beaker carefully into the vacuum chamber and vacuum the samples for 2-3 min on the highest setting (lowest vacuum). Use a metallic spatula to carefully remove any air bubbles that accumulate on the surface. If air bubbles are still present after this step, reheat the mixture and repeat the vacuuming step until all air bubbles have been removed.</li>
	<li>Turn on the vacuum oven and heat it up to 160 &#176;C. Once it has reached the desired temperature, transfer the beaker with the solution into the vacuum oven. 
	NOTE: Always handle the beaker with heat protective gloves.
	<ol>
		<li>Switch on the vacuum to the highest setting (lowest vacuum) available. If a foam layer has produced on top of the solution, turn off the vacuum and remove the bubbles from the surface using a spatula (repeat this step until all air bubbles have been removed).</li>
		<li>Leave the beaker in the vacuum oven for 1 h at the highest vacuum setting. 
		&#8203;NOTE: To keep the vacuum oven clean, clean the external surface of the beaker of silicone oil with a paper towel. </li>
	</ol>
	</li>
</ol>
4. Pouring the samples into the mold
<ol>
	<li>Before pouring the samples into sample molds, remove any remaining air bubbles on the surface of the mixture with a spatula if necessary.</li>
	<li>Carefully pour the solution into a suitable mold, wearing heat-resistant gloves or using adequate protective equipment. Ensure smooth and steady pouring from a low height to reduce the chance of any air bubbles forming (Figure 1: step 5). For molds with complex shapes, coat the mold with a thin layer of oil (other than mineral oil [e.g., castor or silicone oil]) prior to pouring to facilitate removal of the cured sample. 
	NOTE: Preheating of the molds in an oven can help with achieving higher sample homogeneity.</li>
	<li>Remove any air bubbles from the top of the samples quickly with a metallic spatula once poured. If numerous air bubbles have accumulated within the mixture, repeat the vacuum step, provided that the type and shape of the mold permits it.</li>
	<li>Allow the solution to set at room temperature. Although smaller samples may cure in less than 2 h, leave the samples overnight to eliminate any risk of incomplete curing. Store the samples at room temperature (Figure 1: step 6).</li>
</ol>
5. Image acquisition
<ol>
	<li>For image acquisition, place the phantom in the field of view of the imaging device.</li>
	<li>For PAI or ultrasound systems, perform acoustic coupling of the phantom surface to the ultrasound transducer, for example, with ultrasound gel or water. 
	NOTE: If the protocol has been followed correctly, no inhomogeneities should perturb the field of view. Custom phantom holders can assist in repeatable sample positioning between measurements.</li>
	<li>If the acquisition temperature differs from the storing temperature of the phantom, allow the phantom temperature to stabilize with the surroundings.</li>
	<li>Acquire an image.</li>
</ol>
6. Material characterization measurements
NOTE: The purpose of material characterization measurements is verification of the material optical and acoustic properties. It should be noted that the phantom fabrication protocol has shown high reproducibility39, so the general measurement protocols that follow are only provided as guidance if further verification studies are desired. The individual steps of the measurements will depend on the characterization equipment used. Here, a system based on a broadband through-transmission substitution method41 (available at the National Physical Laboratory (NPL), UK) was employed for acoustic characterization and an in-house double-integrating-sphere (DIS) system was used (based on 42) for optical characterization. The setup of the characterization systems is displayed in Supplementary Figure 1. Additional details on the measurement setups (acoustic43; optical42,44) and measurement procedure39 can be found elsewhere. The measurement procedure should be adapted accordingly to each specific characterization system used.
<ol>
	<li>Acoustic characterization 
	NOTE: The acoustic characterization measurements are based on a system employing a 10 MHz center frequency ultrasound transducer (active element diameter of 10 mm) for pulse generation and a broadband hydrophone (30 mm active element diameter bilaminar membrane hydrophone) for pulse detection (both placed in a water tank filled with deionized water; dimensions of 112 cm x 38 cm x 30 cm3). The transducer is driven by a pulser-receiver. Waveforms are acquired using an oscilloscope. More details on the setup and measurement procedure (including system-specific type B effects on the measurements) can be found in 43.
	<ol>
		<li>Prepare samples suitable for the measurement setup (e.g., in this case, circular samples with a diameter of 7-8 cm and thickness of 6-9 mm). Ensure that the samples are of homogeneous composition and free of any impurities, air bubbles, or surface irregularities.</li>
		<li>Measure the thickness of the test sample using vernier calipers and record the temperature of the water tank using a calibrated thermometer.</li>
		<li>Place the sample into the system. Ensure that the sample is correctly aligned with the components of the system. 
		NOTE: An automatically controlled sample holder based on a gimbal mount43 may assist in precise control of the rotation and tilt of the sample.</li>
		<li>Acquire four acoustic pulses for each measurement set: a reference through-water pulse with no sample present in the acoustic path; a through-sample transmission; and acoustic reflections received at the transmitter from the front and rear surfaces of the sample.</li>
		<li>Derive the acoustic properties of the sample from the measurements. Calculate the speed of sound c(f) (in m&#183;s&#8722;1) using the equation (1)43. 
		<img alt="Equation 1" src="/files/ftp_upload/65475/65475eq01.jpg" style="margin: auto;" />&#160; &#160; (1) 
		cw depicts the temperature-dependent speed of sound of water, and &#952;1(f), &#952;2(f), &#952;w(f), and &#952;s(f) are the corresponding unwrapped phase spectra of the front-reflected, back-reflected, through-water, and through-sample voltage pulses, respectively. The frequency-dependent attenuation coefficient (&#945;i(f)) of the material can be derived using the two-sample substitution technique shown in equation (2)43. 
		<img alt="Equation 2" src="/files/ftp_upload/65475/65475eq02v2.jpg" style="margin: auto;" />&#160;&#160;&#160; (2) 
		Uw(f) and Us(f) are the respective voltage magnitude spectra of the through-water and through-sample pulse, &#945;w(f) is the attenuation coefficient of ultrasound (in dB&#183;cm-1) of pure water at the specific water tank temperature45, and d1 and d2 (d2 &#62; d1) are two sample thicknesses. 
		NOTE: For the present protocol, the attenuation accounting for interfacial losses was assessed, finding its impact to be negligible.</li>
		<li>Repeat the measurement more than three times at different positions on the test sample. Calculate the mean and standard deviation of the measurements to derive a final sample value.</li>
	</ol>
	</li>
	<li>Optical characterization 
	NOTE: For optical testing, a double-integrating sphere system was used (based on 42), employing two integrating spheres (50 mm internal diameter) that are connected to two spectrometers via two optical fibers. The reflectance sphere is connected to a light source via a third optical fiber.
	<ol>
		<li>Prepare samples suitable for the measurement setup (e.g., in this case, rectangular samples with a width of 5.9 cm, height of 1.8 cm, and thickness ranging between 2 and 3 mm). Ensure that the samples are of homogeneous composition and free of any impurities, air bubbles, or surface irregularities.</li>
		<li>Turn on the light source and allow it to stabilize according to the manufacturer&#39;s instructions (e.g., 15 min).</li>
		<li>Determine the thickness of the sample using vernier calipers. If applicable, specify the wavelength range and step size for the measurement (e.g., 450-900 nm with a 1 nm step size).</li>
		<li>Record the reference measurements for the transmission and reflectance sphere.
		<ol>
			<li>For the reflectance sphere, first take an open port measurement by recording the reflectance value&#160;R0 with the transmittance sphere removed and light source turned on. Then, record the reflectance value R1 with a reference standard held in front of the reflectance sphere (light source turned on).</li>
			<li>For the transmittance sphere, first take a blocked beam measurement by recording the transmittance value T0 with the aligned reflectance and transmittance spheres and light source turned off. Then, take an incident beam measurement by recording the transmittance value T1 with the aligned reflectance and transmittance spheres and light source turned on. 
			NOTE: A clean surface of the spheres and reference standard must be ensured for the measurements, as the adherence of dust or other contaminants may impact the performance of the components46.</li>
		</ol>
		</li>
		<li>Place the sample between the spheres. Measure the reflectance Rs and transmittance Ts&#160;values. Ensure that the sample is not compressed, as this may impact the measurement accuracy. Placing one sphere on a motorized stage may help to accurately control the distance between the spheres by adapting it to the measured sample thickness.</li>
		<li>Calculate the normalized reflectance MR&#160;and transmittance MT&#160;values using equations (3) and (4)42. 
		<img alt="Equation 3" src="/files/ftp_upload/65475/65475eq03.jpg" style="margin: auto;" />&#160; &#160; (3) 
		<img alt="Equation 4" src="/files/ftp_upload/65475/65475eq04.jpg" style="margin: auto;" />&#160; &#160; (4) 
		rstd depicts the intensity reflected from the 99% reflectance standard.</li>
		<li>Enter the measured values into an inverse adding doubling (IAD) program (source code: http://omlc.org/software/iad/)44 to estimate the optical properties of the material. 
		NOTE: Based on previous reports, the scattering anisotropy factor (g) can be taken as g = 0.7, and the refractive index as n = 1.4 30.</li>
		<li>Repeat the measurement at least three times at different positions along the test sample. Calculate the mean and standard deviation of the measurements to derive a final sample value.</li>
	</ol>
	</li>
</ol>

Fabrication of a Stable, Biologically Relevant Phantom Material

Sarah Bohndiek has previously received research support from CYBERDYNE INC and iThera Medical GmbH, vendors of photoacoustic imaging instruments. The other authors have no conflict of interest related to the present manuscript to disclose.

Here, a protocol is presented that aims to provide a versatile recipe for a stable, biologically relevant material that can be used to create phantoms for calibration measurements and standardization across multimodal acoustic and optical biomedical imaging applications. The material has previously been shown to be stable over time39, to have high batch-to-batch reproducibility, to be safe to use, and to consist of readily available, cost-effective ingredients from standard scientific suppliers. The material properties are independently tunable across relevant acoustic and optical regimes. Furthermore, it is mechanically robust and insoluble in water, thereby withstanding rough handling, and it is inert to water-based coupling agents that are used in ultrasonic/photoacoustic research. It was highlighted that different phantom designs can be created with different types of inclusions, composed of the same or of different material types. Given these properties, the material fulfills the aforementioned key criteria for an ideal biophotonic phantom and shows key advantages compared to other existing tissue-mimicking materials3. By detailing the exact manufacturing process, we hope to minimize variations arising from the fabrication procedure, thereby optimizing its use for calibrating, validating, and tracking the performance of imaging systems.
Two key steps have been identified as being critical to the fabrication process. First, ingredients need to be thoroughly mixed and uniformly heated for the creation of a homogenous material. Using a sonicator and magnetic stirrer for mixing and an oil bath for heating ensures the even distribution of material components within the base matrix. Care needs to be taken that the oil bath does not reach very high temperatures (&#62;180 &#176;C), as this will result in oxidation of the material components, leading to yellowish discoloration. Manual stirring can support the mixing process and compensates for insufficient heating from the material-air interface. The time for sonication and mixing may need to be extended when a higher concentration of TiO2 and/or polymers are used to ensure a homogenous composition of the material. Second, air bubbles need to be removed to prevent the formation of heterogeneities within the base matrix. Whilst this can be achieved with a vacuum pump or oven, careful pouring from a low height should also be practiced to minimize trapping air within the material.
One significant advantage of the material is its thermoplastic properties (derived from the SEBS polymer), allowing it to be reheated and remolded without any significant impact on its acoustic and optical properties39. However, reheating needs to be performed gradually and carefully, as the material can easily burn and oxidize if reheated too quickly. Reheating also becomes more difficult when higher LDPE concentrations are used, as LDPE does not exhibit the same thermoplastic behavior as SEBS.
Several limitations of the protocol remain. Due to the high melting temperature of the polymers (150 &#176;C), phantom molds need to made out of a heat-resistant material, such as glass or stainless steel. Additionally, the material is fairly viscous in liquid state if a high polymer concentration is used to tune the acoustic properties, making the filling of small imaging targets difficult. Finally, tuning of the acoustic properties is thus far limited to a speed of sound range of ~1450-1,516 m&#183;s-1 which supports mimicking tissues such as breast or fat (c = 1,450-1,480 m&#183;s&#8722;1), but may be insufficient for tissues like muscle or kidney (c &#62; 1,520 m&#183;s&#8722;1). The concomitant change of acoustic attenuation should also be taken into consideration.
Here, we have highlighted the application of the material as a stable phantom for ultrasound and optical imaging applications. However, copolymer-in-oil materials have also shown to be of value in elastography applications35, and could potentially allow for compatibility with further imaging modalities such as magnetic resonance imaging. Increased anatomical realism of the phantoms may be achieved using 3D-printed molds, as shown in similar studies29,47,48,49. Early studies have also demonstrated the 3D printability of the material itself, further extending its flexibility in terms of processing and fabrication. These developments highlight the exciting future potential of the material as a widely used, stable phantom medium for multimodal imaging applications.

Establishing the precision and accuracy of novel optical imaging biomarkers through technical validation1,2 is paramount to ensuring their successful implementation in clinical practice. To achieve this, technical validation studies frequently employ durable physical phantoms, which facilitate inter-instrument performance assessment and routine quality control. For widespread use of a phantom material in research and clinical translation, a simple, highly reproducible fabrication protocol is required. An ideal biophotonic phantom material should include the following properties3: (1) independently tunable properties within biologically relevant ranges; (2) mechanical robustness; (3) long-term stability; (4) flexibility in geometry and architecture; (5) safe handling; (6) widely available ingredients that can be purchased from standard scientific suppliers; and (7) low cost. At present, biophotonic applications lack a standardized protocol for a widely accepted phantom material that fulfils the outlined requirements and also includes tunable acoustic properties for hybrid applications, such as photoacoustic imaging (PAI).
Biologically relevant phantom materials targeted for combined optical and acoustic applications include hydrogels4,5, polyvinyl alcohol (PVA)6,7,8,9, and polyvinyl chloride plastisol (PVCP)10,11,12,13,14,15,16. However, these materials are characterized by certain limitations that restrict their application as a stable phantom material. Hydrogels, for example, are prone to dehydration, mechanical damage, and bacterial ingrowth, limiting their shelf life17,18,19. The addition of chemicals can increase the longevity, but common preservatives, such as formaldehyde20 or benzalkonium chloride21, are hazardous and require cautionary measures during handling. Additionally, targets containing water-soluble dyes can diffuse within the base material if not encapsulated. PVA cryogels are characterized by a higher longevity and structural robustness, but their preparation process involves long freeze-thaw cycles22. This can limit the independent tunability of acoustic and optical parameters23 and-if slightly varied-can lead to inhomogeneities6, thereby compromising reproducibility. Moreover, the diffusion of dyes from inclusions has been observed after 1 year13. PVCP has a complex fabrication process that includes high temperatures of up to 180-220 &#176;C13,14,24,25. PVCP also suffers from a lack of a supply chain with scientific suppliers26 and can contain plasticizers based on phthalates, which may cause reproductive and developmental harm27, making them controlled substances in some countries.
Copolymer-in-oil compositions, such as gel wax28,29,30,31 or blends based on thermoplastic styrenic elastomers32,33,34,35,36, exhibit good longitudinal stability and feature tissue-like acoustic and optical properties31,35,36,37, thereby having high potential as a durable phantom candidate in multimodal applications. Additionally, this class of material is cost-effective, non-water absorbing, non-toxic, and biologically inert35,38. The speed of sound c(f) and acoustic attenuation coefficient &#945;(f) can be tuned in a biologically relevant range (Table 1) by variation of the polymer concentration33,35,39, whilst optical absorption &#181;a(&#955;) and reduced scattering &#181;s&#39;(&#955;) coefficients can be primarily varied by the addition of oil-soluble dyes or titanium dioxide (TiO2)39, respectively.
Here, a simple, easy-to-follow protocol is presented for the creation of durable copolymer-in-oil phantoms suitable for use in optical, ultrasound, or photoacoustic device calibration. All ingredients have defined Chemical Abstract Service (CAS) numbers and are readily available from standard scientific suppliers. Potential difficulties in the fabrication procedure are highlighted and ways to overcome them are presented. Whilst the protocol allows the fabrication of materials with a range of acoustic and optical properties, the presented protocol yields a material with a speed of sound of ~1,481 m&#183;s-1, aligning with the speed of sound of water at room temperature (20 &#176;C)40. This value was selected as a neutral standard for representing the wide range of existing tissue properties (Table 1), allowing the establishment of a consistent and reliable reference point for comparison. By providing this detailed protocol, we aim to broaden the uptake and manufacturing reproducibility of this promising phantom material type, thereby facilitating biophotonic, acoustic, and photoacoustic validation studies and supporting routine quality control in preclinical and clinical imaging applications.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Low-density Polyethylene (LDPE)</td>
			<td>Alfa Aesar&#160;</td>
			<td>43949.30 
			CAS: 9002-88-4</td>
			<td>6.70 g 
			5.8% w/w</td>
		</tr>
		<tr>
			<td>Mineral oil</td>
			<td>Sigma Aldrich</td>
			<td>330779-1L 
			CAS: 8042-47-5</td>
			<td>83.80 g 
			72.5% w/w</td>
		</tr>
		<tr>
			<td>Nigrosin&#160;</td>
			<td>Sigma Aldrich&#160;</td>
			<td>211680-100G 
			CAS: 11099-03-9</td>
			<td>0.4 g&#160;</td>
		</tr>
		<tr>
			<td>Polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS)</td>
			<td>Sigma Aldrich&#160;</td>
			<td>200557-250G 
			CAS: 66070-58-4</td>
			<td>25.14 g 
			21.7% w/w</td>
		</tr>
		<tr>
			<td>Silicone oil for oil bath</td>
			<td>Sigma Aldrich&#160;</td>
			<td>85409-1L 
			CAS: 63148-62-9 
			~1 L (depending on size of oil bath)</td>
		</tr>
		<tr>
			<td>Titanium(IV) oxide, anatase (TiO2)</td>
			<td>Sigma Aldrich&#160;</td>
			<td>232033 
			CAS: 1317-70-0</td>
			<td>0.15 g</td>
		</tr>
		<tr>
			<td>Antioxidant (optional; e.g., butylated hydroxytoluene)</td>
			<td>Sigma Aldrich&#160;</td>
			<td>W218405-1KG-K 
			CAS: 128-37-0</td>
			<td>may be added to prevent discolouration if higher fabrication temperatures are used&#160;</td>
		</tr>
		<tr>
			<td>Oil-solule dyes for inclusions (optional)</td>
			<td>e.g., Caligo safe wash relief inks, Cranfield Colours, Cwmbran, UK*</td>
			<td></td>
			<td>may be added depending on preferred absorption</td>
		</tr>
		<tr>
			<td>Bath Sonicator&#160;</td>
			<td>Ultrawave Ltd, UK*</td>
			<td>U500H Ultrasonic Cleaning Bath*</td>
			<td>ideally with temperature control; recommended operating frequencies between 30-50 kHz)</td>
		</tr>
		<tr>
			<td>Crystallising dish for silicone oil bath (up to +200 &#176;C)</td>
			<td>any suitable supplier</td>
			<td></td>
			<td>(ext. diameter ~140 mm for 250 mL glass beaker)</td>
		</tr>
		<tr>
			<td>Glass beaker (~250 mL); glass sample dishes/phantom mould</td>
			<td>any suitable supplier</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Hot plate with magnetic stirrer and thermoregulator (external probe thermocouple) with maximum temperature of &#62; 200 &#176;C</td>
			<td>Thermo Fisher Scientific, UK*</td>
			<td>Velp Scientifica AREC.X Digital Ceramic Hot Plate Stirrer*</td>
			<td></td>
		</tr>
		<tr>
			<td>Laboratory scales / scientific balances accurate to 0.01 g</td>
			<td>any suitable supplier</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Metallic spatula</td>
			<td>any suitable supplier</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Vaccuum oven or vaccum chamber</td>
			<td>Memmert, Germany (Vacuum oven)* 
			 
			Cole-Parmer Instrument Company, UK (Vaccum chamber)*</td>
			<td>VO29 (Vacuum oven) 
			 
			DWK Life Sciences (Kimble) Glass Vacuum Desiccator with Collar (Vaccum chamber)*</td>
			<td></td>
		</tr>
		<tr>
			<td>1. Acoustic characterization system*</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Hydrophone</td>
			<td>GEC Marconi</td>
			<td>30 mm active element diameter bilaminar membrane hydrophone</td>
			<td></td>
		</tr>
		<tr>
			<td>Oscilloscope</td>
			<td>Tektronix UK, Bracknell, UK</td>
			<td>DPO 7254&#160;</td>
			<td></td>
		</tr>
		<tr>
			<td>Pulser&#8211;receiver&#160;</td>
			<td>Olympus NDT, Waltham, MA, USA</td>
			<td>Olympus 5073PR</td>
			<td></td>
		</tr>
		<tr>
			<td>Sample holder</td>
			<td>Newport Spectra-Physics, Didcot, UK</td>
			<td>Newport 605-4 Series Low-Distortion Axial Clamping Gimbal Optic Mount</td>
			<td>may require additional adaptor for sample holding</td>
		</tr>
		<tr>
			<td>Thermometer</td>
			<td>G. H. Zeal, London, UK</td>
			<td>UKAS-calibrated IP 39C spirit-in-glass thermometer</td>
			<td></td>
		</tr>
		<tr>
			<td>Ultrasound transducer&#160;</td>
			<td>Force Technology, Brondby, Denmark</td>
			<td>Transducer of active element diameter 10 mm&#160;</td>
			<td></td>
		</tr>
		<tr>
			<td>Vernier callipers</td>
			<td>any suitable supplier</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Water tank filled with deionized water&#160;</td>
			<td>any suitable supplier</td>
			<td></td>
			<td>requires sufficent size (e.g., dimensions 112 &#215; 38 &#215; 30 cm3)</td>
		</tr>
		<tr>
			<td>2.Optical characterization system*</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Integrating sphere (two)</td>
			<td>Avantes, Apeldoorn, the Netherlands</td>
			<td>AvaSphere-50, 50 cm internal diameter</td>
			<td></td>
		</tr>
		<tr>
			<td>Light source&#160;</td>
			<td>Avantes, Apeldoorn, the Netherlands</td>
			<td>Avalight-HAL-s-mini</td>
			<td></td>
		</tr>
		<tr>
			<td>Motorized stage (optional)</td>
			<td>Thorlabs,</td>
			<td>Thorlabs MTS50</td>
			<td></td>
		</tr>
		<tr>
			<td>Optical fibres (three)</td>
			<td>any suitable supplier</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Reflectance standard</td>
			<td>Labsphere, North Sutton, USA</td>
			<td>99%, white, 1.25&#34; diameter, USRS-99-010, AS-01158-060</td>
			<td></td>
		</tr>
		<tr>
			<td>Spectrometer</td>
			<td>Avantes, Apeldoorn, the Netherlands</td>
			<td>Starline Avaspec-2048</td>
			<td></td>
		</tr>
		<tr>
			<td>Software</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Data acqusition software (e.g., Labview)</td>
			<td>National Instruments, Austin, TX, USA</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Data analysis software (e.g., Matlab)</td>
			<td>Mathworks, Natick, USA</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Inverse adding doubling (IAD) program&#160;</td>
			<td></td>
			<td></td>
			<td>Source code: http://omlc.org/software/iad/</td>
		</tr>
		<tr>
			<td>*Please note that similar equipment may also be used.</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
	</tbody>
</table>

a stable phantom material for optical and acoustic imaging

Establishing tissue-mimicking biophotonic phantom materials that provide long-term stability are imperative to enable the comparison of biomedical imaging devices across vendors and institutions, support the development of internationally recognized standards, and assist the clinical translation of novel technologies. Here, a manufacturing process is presented that results in a stable, low-cost, tissue-mimicking copolymer-in-oil material for use in photoacoustic, optical, and ultrasound standardization efforts.
The base material consists of mineral oil and a copolymer with defined Chemical Abstract Service (CAS) numbers. The protocol presented here yields a representative material with a speed of sound c(f) = 1,481 &#177; 0.4 m&#183;s-1 at 5 MHz (corresponds to the speed of sound of water at 20 &#176;C), acoustic attenuation &#945;(f) = 6.1 &#177; 0.06 dB&#183;cm-1 at 5 MHz, optical absorption &#181;a(&#955;) = 0.05 &#177; 0.005 mm-1 at 800 nm, and optical scattering &#181;s&#39;(&#955;) = 1 &#177; 0.1 mm-1 at 800 nm. The material allows independent tuning of the acoustic and optical properties by respectively varying the polymer concentration or light scattering (titanium dioxide) and absorbing agents (oil-soluble dye). The fabrication of different phantom designs is displayed and the homogeneity of the resulting test objects is confirmed using photoacoustic imaging.
Due to its facile, repeatable fabrication process and durability, as well as its biologically relevant properties, the material recipe has high promise in multimodal acoustic-optical standardization initiatives.

Author Spotlight: A Stable Phantom Material for Optical and Acoustic Imaging  

A Stable Phantom Material for Optical and Acoustic Imaging

Our research is focused on developing new imaging modalities for early cancer detection. In this study in particular, we focused on developing a stable test object, or also called phantom, to validate imaging modalities based on light and/or sound. Different resources have been proposed to develop tissue mimicking materials in the acoustic optical regimen.For example, PVA, hydrogels, polyurethane, or PVCP. This study focuses on a promising new material type based on core polyman oil composition, which overcomes many of the tunability and stability challenges. The field of biomedical optics covers a wide range of imaging modalities that can be applied to some of the key challenges facing medicine today.Many of the all optical imaging modalities are relatively depth limited, but we can also couple light with sound through the photoacoustic effect to take advantage of some of the depth penetration benefits of ultrasound. Photoacoustic imaging has shown promise in a wide range of clinical trials, from imaging inflammation to cancer diagnosis. However, quantitative performance assessment remains challenging due to a lack of available phantom materials that can accurately mimic the optical and acoustic properties of tissue and remain stable over time.Many new optical and photoacoustic imaging systems are being developed, but we lack a standardized reference phantom to validate those systems and to compare their performance. Our material is a promising candidate to fill this gap and support further development and translation of these exciting new techniques into the clinic. In the future, we would like to focus on creating more anatomically realistic phantom designs and architectures that are suitable to evaluate the performance of different system configurations.For example, microscopic, mesoscopic and macroscopic systems, which have different geometries and spatial resolutions.

Following this recipe, three representative phantom designs have been created for the purpose of photoacoustic imaging, targeted for different system designs with different optical illumination and acoustic detection geometries (Figure 3A). If the phantom preparation procedure is performed successfully, the phantom material appears smooth and homogeneous without any trapped air bubbles or impurities, and no artifacts can be seen in the resulting image (here visualized using photoacoustic imaging; Figure 3B,C). The protocol yields a representative material with a speed of sound c(f) = 1481 &#177; 0.4 m&#183;s-1 (corresponding to the speed of sound of water at 20 &#176;C40), acoustic attenuation &#945;(f) = 6.1 &#177; 0.06 dB&#183;cm-1 (both at 5 MHz), optical absorption &#181;a(&#955;) = 0.05 &#177; 0.005 mm-1, and optical scattering &#181;s&#39;(&#955;) = 1 &#177; 0.1 mm-1 (both at 800 nm) (uncertainty depicts the standard deviation from n = 3 independently produced batches by different operators; all measurements were carried out at room temperature [20 &#176;C]).
The optical scattering coefficient can be tuned by the variation of TiO2, whilst the optical absorption coefficient can be tuned by the addition of any oil-soluble dye, here demonstrated with Nigrosin (Table 2 and Figure 3D). Whilst the values in Table 2 are focused on lower absorbing and scattering tissues, such as muscle or breast (Table 1), we have not encountered any difficulties with adding absorbers and scatterers at higher concentrations. However, the addition of optical scatterers/absorbers at higher concentrations may require longer sonication times to achieve homogenous mixing of the solution.
The acoustic attenuation and speed of sound can be tuned by variation of the polymer concentration (Table 3). Here, tuning is thus far limited to a speed of sound range of ~1,450-1,516 m&#183;s-1. Lower respective polymer concentrations may result in low physical stability of the sample, leading to plastic deformation over time34. Higher polymer concentrations result in brittleness and an uneven texture of the material. The range of acoustic properties may help to mimic tissues such as breast or fat (c = 1,450-1,480 m&#183;s&#8722;1), but may be insufficient for tissues such as muscle or kidney (c &#62; 1,520 m&#183;s&#8722;1; Table 1).
Common error sources in phantom preparation include insufficient removal of air bubbles and inhomogeneous mixing of the base components (Figure 4). This can be minimized by vacuuming and careful pouring, and stirring/vortexing, respectively.
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/65475/65475fig02.jpg" /> 
Figure 2:&#160;Experimental setup for the phantom fabrication. The glass beaker containing the phantom ingredients is placed in the silicone oil bath using a clamp to avoid direct contact between the surfaces of the oil bath and the glass beaker. Temperature feedback on the hot plate ensures careful temperature control. Magnetic stirrers enable mixing of the both the silicone oil and phantom ingredients. <a href="https://www.jove.com/files/ftp_upload/65475/65475fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/65475/65475fig03.jpg" /> 
Figure 3: Representative results from the phantom fabrication procedure. (A) Various phantom designs showing versatility for application in different photoacoustic imaging systems. Left: small rectangular phantom with strings embedded at different depths (0.5, 1.5, and 2.5 mm; inter-target distance of 1.25 mm) designed for testing high-resolution imaging systems; middle: cylindrical phantom with two inclusions (inter-inclusion distance of 12 mm) using a green and violet oil-soluble dye, designed for testing tomography systems; right: large rectangular phantom with channels embedded at different depths (6 mm, 10 mm, and 14 mm; inter-inclusion distance of 3.5 mm), designed for testing a handheld system. (B) Example photoacoustic image of the rectangular phantom with embedded strings, acquired at 532 nm with a commercial photoacoustic imaging system. (C) Example photoacoustic image of the cylindrical tomographic phantom, acquired at 800 nm with a commercial photoacoustic imaging system. (D) Phantoms with increasing optical absorption concentrations by increasing concentrations of Nigrosin (concentrations given in weight percentage of the total volume of mineral oil on the image). Figure 3B,C is reproduced from Hacker et al.39. Scale bars = 10 mm. <a href="https://www.jove.com/files/ftp_upload/65475/65475fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/65475/65475fig04.jpg" /> 
Figure 4: Common phantom failures. (A,B) Photographs showing air bubbles trapped inside the base matrix. (C) Insufficient mixing of base components leads to inhomogeneities (red arrows) in the resulting photoacoustic image. Scale bar = 5 mm (A). <a href="https://www.jove.com/files/ftp_upload/65475/65475fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Table 2: Tabular overview of tuning of optical absorption (&#181;a) and scattering (&#181;s&#39;) values. Percentage values are given as weight percentage to the total volume of the base solution (mineral oil, column 1) and to the total weight of the phantom material (column 2). The Nigrosin concentrations depict the total amount of absolute Nigrosin (not stock solution). All samples included 5% butylated hydroxytoluene as an antioxidant (optional). n = 3 measurements per sample. A visual representation of the table can be found in Hacker et al.39. Abbreviation: neg = negligible. <a href="https://www.jove.com/files/ftp_upload/65475/Table 2v3.xlsx" target="_blank">Please click here to download this Table.</a>
Table 3: Tabular overview of tuning of acoustic attenuation (&#945;) and speed of sound (c) values. Described by the power law &#945;0fn with &#945;0 and n parameters obtained from a non-linear least squares &#64257;tting (n = 4 measurements per sample). F depicts the frequency in MHz. Percentage values are given as weight percentage to the total weight of the base solution (mineral oil). All samples included 5% butylated hydroxytoluene as an antioxidant (optional). A visual representation of the table can be found in Hacker et al.39. <a href="https://www.jove.com/files/ftp_upload/65475/65475_Table 3_rev.xlsx" target="_blank">Please click here to download this Table.</a>
Supplementary Figure S1: Setup of the acoustic and optical characterization systems used for verifications. A photograph (A) and schematic (B) of the acoustic characterization system for determination of the acoustic attenuation coefficient and speed of sound are displayed. Individual system components are denoted by annotations HP (HydroPhone), S (Sample), and T (Transducer) in the photo and schematic. A photograph (C) and schematic (D) of the double-integrating sphere system for the evaluation of the optical absorption coefficient and reduced scattering coefficient are shown. Individual system components are denoted by annotations S (Sample), RS (Reflectance Sphere), TS (Transmission Sphere), OF (Optical Fiber), and MS (Motorized Stage) in the photo and schematic. This figure is reproduced from Hacker et al. 39. <a href="https://www.jove.com/files/ftp_upload/65475/Suppl. Fig 1.pdf" target="_blank">Please click here to download this File.</a>

Watch this Scientific Journal Video about A Stable Phantom Material for Optical and Acoustic Imaging at JoVE.com

This protocol describes the fabrication of a stable, biologically relevant phantom material for optical and acoustic biomedical imaging applications, featuring independently tunable acoustic and optical properties.

Establishing tissue-mimicking biophotonic phantom materials that provide long-term stability are imperative to enable the comparison of biomedical imaging ...

a-stable-phantom-material-for-optical-and-acoustic-imaging

Research

JoVE Journal

Medicine

Preparation and Heating of the Phantom Material Mixture 

Begin the sonication of 0.15 grams of titanium dioxide and one milliliter of the absorber dye stock solution in 100 milliliters of mineral oil at 90 degrees Celsius for 60 minutes. Let all the components dissolve completely. Use suitable glassware and silicone oil to create an oil bath and carefully secure it on the hot plate.For uniform heat distribution, place a magnetic stir bar inside the oil bath. Turn on the hot plate, set the heating temperature to 160 degrees Celsius and adjust the stir to 50 RPM. Next, weigh 25.14 grams of SEBS and 6.70 grams of LDPE and transfer them into the glass beaker containing the sonicated mineral oil.Place a stir bar in the beaker and transfer it to the center of the oil bath to heat the measured components. When the added polymers float over the mineral oil, manually stir the mineral oil solution using a metal spatula and distribute the floating polymer inside the mineral oil. Leave the mixture at 160 degrees Celsius for 1.5 hours until all the polymer is dissolved and the solution appears uniformly mixed, smooth, and homogenous.

Vacuuming and Pouring of the Phantom Material Samples into the Mold

To begin, place the hot beaker filled with the uniformly mixed, smooth, and homogenous phantom material solution into the vacuum chamber. Vacuum the samples on the lowest vacuum setting for two to three minutes. Remove any air bubbles accumulated on the surface using a metal spatula.If air bubbles persist, reheat the mixture and repeat the vacuuming step until complete removal of the air bubbles. In the case of complex shaped molds, coat the mold with a thin layer of oil before pouring. Wear heat resistant gloves, use adequate protective equipment, and carefully pour the solution into a suitable mold without introducing any air bubbles.Once poured, quickly remove any air bubbles from the top of the samples using a metal spatula. Allow the solution to be set overnight at room temperature. Three representative phantom material designs were created for photoacoustic imaging targeted for different system designs with different optical illumination and acoustic detection geometries.The successful procedure resulted in smooth and homogenous phantom material preparation without trapped air bubbles, impurities, or artifacts. Insufficient removal of air bubbles and inhomogenous mixing of base components resulted in inhomogeneities in the resulting photoacoustic image.

1.8K Views.  University of Cambridge.  This protocol describes the fabrication of a stable, biologically relevant phantom material for optical and acoustic biomedical imaging applications, featuring independently tunable acoustic and optical properties. 

Fabrication of a Stable, Biologically Relevant Phantom Material

Podsumowanie