Agarose-based Tissue Mimicking Optical Phantoms for Diffuse Reflectance Spectroscopy

Podsumowanie

Here, we demonstrate how agarose-based tissue-mimicking optical phantoms are made and how their optical properties are determined using a conventional optical system with an integrating sphere.

Streszczenie

This protocol describes how to make agarose-based tissue-mimicking phantoms and demonstrates how to determine their optical properties using a conventional optical system with an integrating sphere. Measuring systems for the acquisition of the diffuse reflectance and total transmittance spectra are constructed with a broadband white light source, a light guide, an achromatic lens, an integrating sphere, a sample holder, an optical fiber probe, and a multi-channel spectrometer. An acrylic mold consisting of two rectangular acrylic pieces and a U-shaped acrylic piece is constructed to create an epidermal phantom and a dermal phantom with whole blood. The application of a sodium dithionite (Na₂S₂O₄) solution to the dermal phantom enables the researcher to deoxygenate hemoglobin in red blood cells distributed in the dermal phantom. The inverse Monte Carlo simulation with the diffuse reflectance and total transmittance spectra measured by a spectrometer with an integrating sphere is performed to determine the absorption coefficient spectrum µ_a(λ) and the reduced scattering coefficient spectrum µ_s'(λ) of each layer phantom. A two-layered phantom mimicking the diffuse reflectance of human skin tissue is also demonstrated by piling up the epidermal phantom on the dermal phantom.

Wprowadzenie

Optical phantoms are objects mimicking the optical properties of biological tissues and have been widely used in the biomedical optics field. They are designed so that the optical properties, such as light scattering and absorption coefficients, match with those of living human and animal tissues. Optical phantoms are generally used for the following purposes: simulating the light transport in biological tissues, calibrating a newly developed optical system design, evaluating the quality and performance of existing systems, comparing the performance between systems, and validating the ability of the optical methods to quantify the optical properties^1,2,3,4,5. Therefore, easy-to-get substances, a simple fabrication process, a high reproducibility, and an optical stability are required for making optical phantoms.

Various types of optical phantoms with different base materials such as aqueous suspension⁶, gelatin gel⁷, agarose gel^8,9,10, polyacrylamide gel¹¹, resin^{12,13,14,15,16}, and room-temperature-vulcanizing silicone¹⁷ have been reported in previous literature. It has been reported that gelatin- and alginate-based gels are useful for optical phantoms with heterogeneous structures¹⁸. Alginate phantoms have a suitable mechanical and thermal stability for evaluating photothermal effects such as laser ablation studies and laser-based hyperthermia studies¹⁸. Agarose gels have the ability to fabricate heterogeneous structures, and their mechanical and physical properties are stable for a long time¹⁸. High-purity agarose gels have a very low turbidity and a weak optical absorption. Therefore, optical properties of agarose-based phantoms could easily be designed with the appropriate light scattering and absorbing agents. Recently, styrene-ethylene-butylene-styrene (SEBS) block copolymers¹⁹ and polyvinyl chloride (PVC) gels²⁰ have been reported as interesting phantom materials for optical and photoacoustic techniques.

Polymer microspheres^7,12,21,22, titanium oxide powder¹, and lipid emulsions^23,24,25,26 such as milk and lipid emulsion are used as light scattering agents, whereas black ink^27,28 and molecular dyes^29,30 are used as light absorbers. Diffuse reflectance spectra of most living organs are dominated by the absorption of oxygenated and deoxygenated hemoglobin in red blood cells. Therefore, hemoglobin solutions^31,32 and whole blood^8,9,10,33,36 are often used as light absorbers in the phantoms for a diffuse reflectance spectroscopy and multispectral imaging.

The method described in this article is used to create an optical phantom mimicking the light transport in biological tissues and to characterize its optical properties. As an example, a two-layered optical phantom mimicking optical properties of human skin tissue is demonstrated. The advantages of this method over alternative techniques are the ability to represent diffuse reflectance spectra of living biological tissues in the visible to near-infrared wavelength region, as well as the simplicity to make it, using easily available materials and conventional optical instruments. Therefore, the optical phantoms made by this method will be useful for the development of optical methods based on diffuse reflectance spectroscopy and multispectral imaging.

Protokół

1. Construction of a Conventional Diffuse Reflectance and Total Transmittance Spectroscopic System

Note: Construct the measuring systems for the diffuse reflectance and total transmittance spectra using a broadband white light source, a light guide, an achromatic lens, an integrating sphere, a sample holder, an optical fiber, and a multi-channel spectrometer. The role of the light trap is to remove the specular reflection component from the reflectance spectrum. The sample holder of the integrating sphere consists of a mounting plate and a dovetail and spring-loaded clamp assembly that holds the sample against the port. The dovetail and spring-loaded clamp assembly are removed from the sample holder and a hand-made cubic pedestal of polystyrene foam is attached to the mounting plate instead. The layouts of the optical components, shown in Figure 1a and 1b, can be referred to for the construction procedure for the diffuse reflectance measurements and the total transmittance measurements, respectively.

1. Connect the spectrometer and a personal computer using the universal serial bus (USB) cable provided.
2. Attach the port adapter to a detector port of the integrating sphere. Connect the spectrometer and the port adapter of the integrating sphere using an optical fiber. Connect the 150 W halogen lamp light source and the light guide.
3. Attach the sample holder to a sample port of the integrating sphere. Attach the light trap to an appropriate port of the integrating sphere when performing the diffuse reflectance measurements. Turn on the halogen lamp light source to illuminate a sample via the light guide and the achromatic lens.
4. Open the operating software of the spectrometer.

2. Preparation of an Acrylic Mold

Note: An acrylic mold that consists of two rectangular acrylic pieces and a U-shaped acrylic piece is constructed to create a monolayer gel phantom. Figure 2 can be referred to for this construction procedure.

1. Cut out the two rectangular acrylic pieces from a 2-mm-thick acrylic plate to an optional size.
2. Cut out an acrylic piece from a 1-mm-thick acrylic plate to an optional size. Cut the 1-mm-thick acrylic piece so that it becomes a U-shaped piece to be used for the mold to make 1-mm thick epidermal phantoms.
3. Cut out an acrylic piece from a 5-mm-thick acrylic plate to an optional size. Cut the 5-mm-thick acrylic piece so that it becomes a U-shaped piece to be used as a mold to make 5-mm thick dermal phantoms.
4. Remove any burrs from each acrylic piece using a metal file.
5. Make the epidermal phantom mold by holding the 1-mm-thick U-shaped piece with the two 2-mm-thick acrylic pieces and fixing them with five foldback clips.
6. Make the dermal phantom mold by holding the 5-mm-thick U-shaped piece with the two 2-mm-thick acrylic pieces and fixing them with five foldback clips.

3. Preparation of Base Material

1. Put 500 mL of standard saline with 0.9% (w/v) NaCl in a pod. Slowly add 5 g of agarose powder while stirring the mixture to avoid clumping.
2. Heat the mixture of agarose powder and saline by an electric cooking heater with a 1,000 W power setting for 5 min.
3. Once the mixture boils, keep the mixture on low heat for 3 min.
4. Cool the mixture to a temperature of about 70 °C. Then pour the mixture into a container and keep it in a constant temperature bath at 60 °C for 30 min before making a phantom.

4. Preparation of Skin-mimicking Optical Phantoms

Note: A coffee solution is used to mimic the absorption spectrum of melanin. The coffee solution contains a brown pigment called melanoidin. The absorption spectrum of melanoidin has been reported to be similar to that of melanin¹⁰.

1. Prepare an epidermal phantom
   1. Pour 100 mL of pure water into the coffee maker reservoir. Place a filter in the coffee maker basket. Add 24 g of ground coffee into the filter. Turn on the coffee maker and press the brew button to begin brewing.
   2. Put 4 mL of brewed coffee and 16 mL of saline in a glass bottle to make a coffee solution.
   3. Put 5 mL of lipid emulsion (e.g., intralipid 10%) and 10 mL of the coffee solution into a transparent plastic cup. Slowly add 35 mL of the base material to this mixture while stirring.
   4. Aspirate the mixture into a syringe and inject it slowly into the epidermal phantom mold while avoiding any bubble formation. Cool the acrylic mold containing the mixture at 5 °C for 20 min.
   5. Remove the foldback clips from the mold. Slide one of the acrylic pieces outward and remove it from the mold. Take the 1-mm-thick solidified gel phantom out of the mold and cut it to the desired size using a surgical scalpel.
   6. Place and hold the gel phantom between two slide glasses.
2. Prepare a dermal phantom containing oxygenated blood
   1. Take 5.0 mL of lipid emulsion and 0.4 mL of whole equine blood with 45%-hematocrit and put into a transparent plastic cup. Slowly add 44.6 mL of the base material while stirring the mixture.
   2. Aspirate the mixture into a syringe and inject it slowly into the dermal phantom mold while avoiding any bubble formation. Cool the acrylic mold containing the mixture at 5 °C for 20 min.
   3. Remove the foldback clips from the mold. Slide one of the acrylic pieces outward and remove it from the mold. Take the 5-mm-thick solidified gel phantom out of the mold and cut it to the desired size using a surgical scalpel.
   4. Place and hold the gel phantom between two slide glasses.
3. Prepare a dermal phantom containing deoxygenated blood
   1. Put a dermal gel phantom containing oxygenated blood (from step 4.2.3) on a glass dish.
   2. Dissolve 1 g of sodium dithionite (Na₂S₂O₄) into 20 mL of saline in a glass bottle.
   3. Add 0.05 g/mL of Na₂S₂O₄ solution onto the phantom using a syringe to deoxygenate the blood in the phantom.
   4. Place and hold the phantom between two slide glasses to prevent it drying out.
4. Prepare a two-layered phantom
   1. Drop 0.1 mL of saline onto a dermal phantom to ensure optical coupling between the epidermal and dermal layers. Place the epidermal phantom on the dermal phantom.
   2. If any air bubbles are present between the layers, push them out by stroking the surface of the two-layered phantom with a fingertip.
   3. Hold the two-layered phantom between two slide glasses to prevent it drying out.

5. Acquisition of the Diffuse Reflectance Spectra

1. Acquisition of dark spectra
   Note: The charge-coupled device (CCD) sensor in the spectrometer can estimate light intensity based on an electrical signal generated in response to incident light. However, there is dark noise³⁷ which is independent of the signals generated by photons but is dependent on the device temperature, even if the sensor does not detect the light. To accurately measure the spectral intensity of light, the dark current signal should be measured as a dark spectrum and then subtracted from the sample spectrum. The dark spectrum is a spectrum taken with the light path blocked.
   1. Position the integrating sphere at an optimal position for the diffuse reflectance measurements (Figure 1a).
   2. Turn off the halogen lamp light source. Block the light path to the spectrometer using a port plug or a shielding plate.
   3. Select the Store dark command from the file menu to store a dark spectrum.
   4. Select the Subtract dark spectrum command from the file menu to subtract the dark spectrum from the measured sample spectrum (see below).
2. Acquisition of reference spectra
   Note: The optical properties of the components used in this experiment, such as the light source, light guide, achromatic lens, optical fiber, and spectrometer, have their own wavelength-dependences. Therefore, the spectral intensity of light passed through these optical components should be measured as a reference spectrum. For the measurement of a diffuse reflectance spectrum, the reference spectrum is a spectrum taken with a standard white diffuser illuminated with the light from the light source.
   1. Turn on the halogen lamp light source by pressing the power button. Warm up the lamp for at least 10 min before acquiring a reference spectrum.
   2. Place a standard white diffuser (e.g., Spectralon) at the sample port of the integrating sphere.
   3. Adjust the integration time of the spectrometer by selecting the suitable value from the drop-down list in the spectrometer operating software so that the peak signal intensity is approximately 75% of the spectrometer intensity maximum.
   4. Select the Store reference command from the file menu to store a reference spectrum.
3. Acquisition of sample spectra
   Note: A spectrum of the diffuse reflectance of the sample is acquired and saved on the hard drive of a personal computer using the same acquisition conditions.
   1. Place the epidermal phantom sandwiched by the two slide glasses at the sample port. Select the Save command from the file menu to save a diffuse reflectance spectrum to a file.
   2. Repeat step 5.3.1 for the dermal and two-layered phantoms.

6. Acquisition of the Total Transmittance Spectrum

1. Acquisition of dark spectra
   Note: The sensor in the spectrometer can estimate light intensity based on an electrical signal generated in response to incident light. However, there is dark noise which is independent of the signals generated by photons but is dependent on the device temperature, even if the sensor does not detect the light. To accurately measure the spectral intensity of light, the dark current signal should be measured as a dark spectrum and then subtracted from the sample spectrum. The dark spectrum is a spectrum taken with the light path blocked.
   1. Position the integrating sphere at an optimal position for the total transmittance measurements (Figure 1b).
   2. Remove the light trap from the port of the integrating sphere and attach a port plug to the port.
   3. Turn off the halogen lamp light source. Block the light path to the integrating sphere using a port plug or shielding plate.
   4. Select the Store dark command from the file menu to store a dark spectrum.
   5. Select the Subtract dark spectrum command from the file menu to subtract the dark spectrum from the measured sample spectrum (see below).
2. Acquisition of reference spectra
   Note: The optical properties of the components used in this experiment, such as the light source, light guide, achromatic lens, optical fiber, and spectrometer, have their own wavelength-dependences. Therefore, the spectral intensity of the light passed through these components should be measured as a reference spectrum. For the measurement of the total transmittance spectrum, the reference spectrum is a spectrum taken when the light from the light source is directly entering the integrating sphere through the sample port.
   1. Turn on the halogen lamp light source by pressing the power button. Warm up the lamp for at least 10 min before acquiring a reference spectrum.
   2. Regulate the integration time of the spectrometer by selecting the suitable value from the drop-down list of integration times in the operating software of the spectrometer so that the greatest light intensity shows a signal that is approximately 75% of the maximum values.
   3. Select the Store reference command from the file menu to store a reference spectrum.
3. Acquisition of sample spectra
   Note: The spectrum of the total transmittance of the sample is acquired and saved on the hard drive of a personal computer using the same acquisition conditions.
   1. Place the epidermal phantom sandwiched by the two slide glasses at the sample port. Select the Save command from the file menu to save a total transmittance spectrum to a file.
   2. Repeat step 6.3.1 for the dermal and two-layered phantoms.

7. Estimating the Absorption and Light-scattering Properties

Note: A set of the diffuse reflectance spectrum and the total transmittance spectrum is saved to the hard drive of a personal computer and analyzed offline. An inverse Monte Carlo simulation^8,38,39,40 is then performed to estimate the absorption coefficient spectrum µ_a(λ) and the reduced scattering coefficient spectrum µ_s’(λ). In this inverse Monte Carlo simulation, the estimated scattering coefficient µ_s, under the assumption that the anisotropy factor g is 0, is regarded as the reduced scattering coefficient µ_s’. Both the reflectance and the transmittance data are used for a single simulation run. The detailed algorithm used in this protocol has been reported in previous literature^8,39. We estimated the absorption coefficient spectrum µ_a(λ) and the reduced scattering coefficient spectrum µ_s’(λ) of an epidermal layer from a set of the diffuse reflectance spectrum and the total transmittance spectrum obtained from the epidermal layer. In the same way, we estimated µ_a(λ) and µ_s’(λ) of a dermal layer from a set of the diffuse reflectance spectrum and the total transmittance spectrum obtained from the dermal layer.

1. Open an input file for the Monte Carlo simulation.
2. Fill in the values of the measured diffuse reflectance and the total transmittance at the specific wavelength range from 400 to 700 nm at 10 nm-intervals in the input data file. Fill in the value of the phantom thickness in the input data file.
3. Set the refractive index n of a layer to be an appropriate value in the input data file (e.g., n = 1.33 at 550 nm). Set the value of the anisotropy factor g to be 0 in the input data file.
4. Set the initial values of the absorption coefficient µ_a and the scattering coefficient µ_s to be the appropriate values in the input data file (e.g., µ_a = 0.01, µ_s = 0.1).
5. Execute the inverse Monte Carlo simulation program.
6. Type the input file name and then run the simulation.
7. Open the output file and check the final values of µ_a and µ_s after the iterative simulation is terminated.
8. Repeat steps 7.1 - 7.7 for other desired wavelengths.

Wyniki

Figure 3 shows the representative estimated spectra of the reduced scattering coefficient and the absorption coefficient for the epidermal phantom and dermal phantom. The results shown in Figure 3 are the averages of ten measurements of both reflectance and transmittance spectra. The reduced scattering coefficient µ_s' has a broad scattering spectrum, exhibiting a higher magnitude at shorter w...

Dyskusje

The most critical step in this protocol is the temperature control of the base material. The temperature to maintain the base material ranged from 58 to 60 °C. If the temperature is more than 70 °C, a denaturation of both the lipid emulsion and the whole blood will occur. As a consequence, the optical properties of the phantom will deteriorate. If the temperature is less than 40 °C, the base material will be ununiformly gelled and, thus, the light scattering and absorption agents will be heterogeneously di...

Materiały

Name	Company	Catalog Number	Comments
150-W halogen-lamp light source	Hayashi Watch Works Co., Ltd, Tokyo, Japan	LA-150SAE
Light guide	Hayashi Watch Works Co., Ltd, Tokyo, Japan	LGC1-5L1000
Integrating Sphere	Labsphere Incorporated, North Sutton, NH, USA	RT-060-SF
Port adapter	Labsphere Incorporated, North Sutton, NH, USA	PA-050-SMA-SF
Light trap	Labsphere Incorporated, North Sutton, NH, USA	LTRP-100-C
Spectralon white standard with 99% diffuse reflectance	Labsphere Incorporated, North Sutton, NH, USA	SRS-99-020
Optical fiber	Ocean Optics Inc., Dunedin, Florida, USA	P400-2-VIS-NIR
Miniature Fiber Optic Spectrometer	Ocean Optics Inc., Dunedin, Florida, USA	USB2000
Achromatic lens	Chuo Precision Industrial Co.,Ltd, Tokyo, Japan	ACL-50-75M
Intralipid	Fresenius Kabi AB, Uppsala, Sweden	Intralipid 10%
Coffee (Blendy Mocha Blend Regular Coffee)	Ajinomoto AGF, Inc. Tokyo, Japan	Unavailable
Whole blood	Nippon Bio-Test Laboratories Inc. Saitama, Japan	0103-2
Agarose	Nippon Genetics Co., Ltd, Tokyo, Japan	NE-AG02
Cooking heater	TOSHIBA CORPORATION Tokyo, Japan	HP-103K