This study was supported by the National Health and Medical Research Council of Australia (project grant no. 6288480) and the Scobie and Clare MacKinnon Trust.

1. Micromixing an RT Reaction
<ol>
	<li>Before performing an RT reaction with micromixing, equilibrate the micromixer to the desired temperature of the RT reaction.
		<ol>
				<li>Place the micromixer inside a 37&deg;C (or the temperature recommended by 	the RT supplier) incubator for at least 1 hour prior to the onset of the RT 	reaction.</li>
		</ol>
	</li>
	<li>Set up the RT mix according to the reverse transcriptase supplier's (e.g. MMTV-RT from Promega, Omniscript from Qiagen) instructions, except use single-cell amounts of input total RNA (e.g. 0.1-1pg/&mu;l), instead of the ng-&mu;g amounts recommended by suppliers.
		<ol>
				<li>We use standard sterile, nuclease-free 200&mu;L thin-walled PCR tubes.</li>
		</ol>
	</li>
	<li>Position RT tubes securely into the micromixer as soon as they are ready for mixing. The micromixer should remain inside the 37&deg;C incubator for the duration of the RT reaction.</li>
	<li>Select the appropriate frequency and amplitude of micromixing. In this example we use 150Hz. </li>
	<li>Switch the micromixer on and leave it on for the entire duration of the RT reaction (60 minutes).</li>
	<li>Switch the micromixer off and take the RT tubes out once the RT reaction is complete. </li>
	<li>Place the RT tubes on ice and proceed as normal with further applications such as quantitative Polymerase Chain Reaction (qPCR or real-time PCR).</li>
</ol>
2. Representative Results: 
The benefit of micromixing in the context of RT reactions is an increase in cDNA yield relative to when other mixing methods (e.g. shaking, vortexing or trituration) are used. This can be seen, for example, upon subsequent analysis of the cDNA using quantitative Polymerase Chain Reaction (qPCR or real-time PCR). Figure 2A illustrates the effects of micromixing for the first 5 minutes (blue, "micromixed5") or the entire 60 minutes (red, "micromixed60") compared with trituration of the RT reaction immediately prior to the RT incubation (black, "trituration"). In this case the volume of the preceding RT reaction was 25&mu;L and it contained 2.5pg of total RNA. qPCR traces using primers designed to detect cDNA representing Nurr-1 mRNA are shown above, and the means &plusmn;SEMs of the number of cycles to reach 50% maximum fluorescence in 3 repeats of this same experiment are plotted below. The asterisk denotes a statistically significant difference (one-way ANOVA with Tukey multiple comparisons). Note that micromixing for the first 5 minutes of the preceding RT reaction produced a non-significant improvement over trituration whereas micromixing for the entire 60 minutes of the preceding RT reaction produced a significant improvement over trituration, the magnitude of which was equivalent to approximately 15 qPCR cycles, on average.
The benefit of micromixing can also be seen in melting curve analysis of the subsequent qPCR products obtained. In the experiment illustrated in Figure 2B, micromixing for the entire 60 minutes of the preceding RT reaction resulted in a consistent qPCR signal in duplicate samples (Figure 2Ba, 2 red traces), whereas micromixing for the first 5 minutes or trituration only produced inconsistent qPCR traces (Figure 2Ba, 2 blue traces and 2 black traces, respectively). The grey traces are negative controls ("neg.") in which cDNA was left out of the qPCR reaction. When the qPCR products from this experiment were denatured by ramping their temperature (i.e. melting curve analysis) it was apparent that appropriate PCR products (i.e. an amplicon that was identical to that obtained when much higher concentrations of mRNA were reverse transcribed and amplified by qPCR, data not shown) were present only following RT reactions that had been micromixed for 60 minutes (Figure 2Bb, 2 red traces). All the others (i.e. micromixed5, trituration and negative controls) generated alternative amplicon products (e.g. primer dimers).
<img src="/files/ftp_upload/3144/3144fig1.jpg" alt="Figure 1"/> Figure 1. Flow diagram of the protocol for applying micromixing to standard laboratory RT reactions. More detailed descriptions of the physical principle involved, the micromixer and how to build an in-house micromixer are provided in references 13,14
<img src="/files/ftp_upload/3144/3144fig2.jpg" alt="Figure 2"/> Figure 2.Representative qPCR data illustrating the benefits of micromixing applied to preceding RT reactions comprising single-cell quantities of mRNA in otherwise standard laboratory RT reactions. A Example qPCR traces detecting cDNA representing mRNA encoding the Nurr-1 gene. The preceding RT reactions contained 2.5pg of total RNA in a volume of 25&mu;L and were performed in an incubator at 37&deg;C for 60 minutes. RT reactions were mixed by trituration of the RT mix prior to incubation (black traces, "trituration"), micromixed during the first 5 minutes of the RT reaction (blue traces, "micromixed5") or micromixed for the entire 60 minutes of the RT reaction (red traces, "micromixed60"). Means &plusmn; SEMs of the number of qPCR cycles required to reach 50% maximum fluorescence are plotted below for n=3 repeats of this experiment. Asterisk indicates a significant difference (one-way ANOVA with Tukey multiple comparisons). B Another qPCR experiment examining Nurr-1 cDNA product, this time following RT reactions containing 25pg of total RNA in a volume of 25&mu;L. qPCR traces (a) as well as melting curve analysis of the qPCR products obtained (b) are shown for the different mixing conditions. Negative controls in which no cDNA was included in the preceding RT reaction are also included (gray traces, "neg."). RT reactions with much higher concentrations of mRNA were also performed and produced melting curve peaks (data not shown) identical to those in (b) for micromixed60 (red traces) samples.

<ol>
	<li>Livesey, F. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Brief+Funct+Genomic+Proteomic.">Brief Funct Genomic Proteomic.</a> 2 (1), 31-31 (2003).</li><li>Aumann, T. D., Gantois, I., Egan, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Exp Neurol. 213 (2), 419-419 (2008).</li><li>Ottino, J. M., Wiggins, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Philos Transact A Math Phys Eng Sci. 362 (1818), 923-923 (2004).</li><li>Losey, M. W., Jackman, R. J., Firebaugh, S. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> J Microelectromech. Syst. 11, 709-709 (2002).</li><li>Bontoux, N., Dauphinot, L., Vitalis, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Lab Chip. 8 (3), 443-443 (2008).</li><li>Marcus, J. S., Anderson, W. F., Quake, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Anal Chem. 78 (9), 3084-3084 (2006).</li><li>Marcus, J. S., Anderson, W. F., Quake, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Anal Chem. 78 (3), 956-956 (2006).</li><li>Warren, L., Bryder, D., Weissman, I. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Proc Natl Acad Sci U S A. 103 (47), 17807-17807 (2006).</li><li>Jiao, Z. J., Huang, X. Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Microfluidics Nanofluidics. 6, 847-847 (2009).</li><li>Ahmed, D., Xiaole, M., Juluri, B. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Microfluidics Nanofluidics. 7, 727-727 (2009).</li><li>Paxton, W. F., O'Hara, M. J., Peper, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Anal Chem. 80, 4070-4070 (2008).</li><li>Autom, L. a. b. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> 11, 399-399 (2006).</li><li>Petkovic-Duran, K., Manasseh, R., Zhu, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> 47 (4), 827-827 (2009).</li><li>Boon, W. C., Petkovic-Duran, K., White, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> 50 (2), 116-116 (2011).</li><li>Liu, R. H., Lenigk, R., Druyor-Sanchez, R. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Anal Chem. 75 (8), 1911-1911 (1911).</li><li>Riley, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ann+Rev+Fluid+Mech.">Ann Rev Fluid Mech.</a> 33, 43-43 (2001).</li><li>Whitehill, J., Neild, A., Ng, T. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Applied Physics Letters. 96 (5), 053501-053501 (2010).</li></ol>

The authors have nothing to disclose.

The method of application of micromixing to standard laboratory RT reactions described here can, of course, involve mRNA harvested via any method (e.g. cell lysis, laser capture microdissection). It can also comprise any brands or types of RT reagents, any temperature (within the tolerance of the materials of the micromixer), and any period of time. For example, we have observed improved cDNA yields from RT reactions comprising random hexamer or oligo-dT primers. It might also be applied to other biochemical transform...

<table border="1">
	<tbody>
		<tr>
			<th>Name of the reagent	</th>
			<th>Company	</th>
			<th>Catalogue number	</th>
			<th>Comments (optional)</th>
		</tr>
		
		<tr>
			<td>Total RNA was isolated from snap frozen acutely prepared adult mouse midbrain slices</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>PicoPure RNA Isolation Kit	</td>
			<td>Arcturus, CA, USA	</td>
			<td>KIT0204	</td>
			<td>The kit is now available from Applied Biosystems</td>
		</tr>
		
		<tr>
			<td>DNA-free DNase Treatment and Removal Reagents	</td>
			<td>Ambion	</td>
			<td>AM1906M</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Random hexamer primers	</td>
			<td>Promega	</td>
			<td>C1181</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>AMV-RT	</td>
			<td>Promega	</td>
			<td>M5101</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>dNTP set	</td>
			<td>Promega	</td>
			<td>U1240</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>RNasin Ribonuclease Inhibitor	</td>
			<td>Promega	</td>
			<td>N2111</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Nuclease-Free Water	</td>
			<td>Promega	</td>
			<td>P1193</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>SYBR Green PCR Master Mix	</td>
			<td>Applied Biosystem	</td>
			<td>4309155</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Hprt forward (20mer):CTT TGC TGA CCT GCT GGA TT</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Hprt reverse (20mer):TAT GTC CCC CGT TGA CTG AT</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Nurr1 forward (23mer):CAG CTC CGA TTT CTT AAC TCC AG</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Nurr1 reverse (23mer):GGT GAG GTC CAT GCT AAA CTT GA</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>NanoDrop 1000 Spectrophotometer. </td>
			<td>Thermo Scientific</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		
		<tr>
			<td>Corbett Rotor Gene RG-6000</td>
			<td>Corbett Life Science</td>
			<td>&nbsp;</td>
			<td>Corbett Life Science was acquired by QIAGEN in July 2008</td>
		</tr>
		
	</tbody>
</table>

increasing cdna yields from single-cell quantities of mrna in standard laboratory reverse transcriptase reactions using acoustic microstreaming

Correlating gene expression with cell behavior is ideally done at the single-cell level. However, this is not easily achieved because the small amount of labile mRNA present in a single cell (1-5% of 1-50pg total RNA, or 0.01-2.5pg mRNA, per cell 1) mostly degrades before it can be reverse transcribed into a stable cDNA copy. For example, using standard laboratory reagents and hardware, only a small number of genes can be qualitatively assessed per cell 2. One way to increase the efficiency of standard laboratory reverse transcriptase (RT) reactions (i.e. standard reagents in microliter volumes) comprising single-cell amounts of mRNA would be to more rapidly mix the reagents so the mRNA can be converted to cDNA before it degrades. However this is not trivial because at microliter scales liquid flow is laminar, i.e. currently available methods of mixing (i.e. shaking, vortexing and trituration) fail to produce sufficient chaotic motion to effectively mix reagents. To solve this problem, micro-scale mixing techniques have to be used 3,4. A number of microfluidic-based mixing technologies have been developed which successfully increase RT reaction yields 5-8. However, microfluidics technologies require specialized hardware that is relatively expensive and not yet widely available. A cheaper, more convenient solution is desirable. The main objective of this study is to demonstrate how application of a novel "micromixing" technique to standard laboratory RT reactions comprising single-cell quantities of mRNA significantly increases their cDNA yields. We find cDNA yields increase by approximately 10-100-fold, which enables: (1) greater numbers of genes to be analyzed per cell; (2) more quantitative analysis of gene expression; and (3) better detection of low-abundance genes in single cells. The micromixing is based on acoustic microstreaming 9-12, a phenomenon where sound waves propagating around a small obstacle create a mean flow near the obstacle. We have developed an acoustic microstreaming-based device ("micromixer") with a key simplification; acoustic microstreaming can be achieved at audio frequencies by ensuring the system has a liquid-air interface with a small radius of curvature 13. The meniscus of a microliter volume of solution in a tube provides an appropriately small radius of curvature. The use of audio frequencies means that the hardware can be inexpensive and versatile 13, and nucleic acids and other biochemical reagents are not damaged like they can be with standard laboratory sonicators.

Watch this Scientific Journal Video about Increasing cDNA Yields from Single-cell Quantities of mRNA in Standard Laboratory Reverse Transcriptase Reactions using Acoustic Microstreaming at JoVE.com

Increasing cDNA Yields from Single-cell Quantities of mRNA in Standard Laboratory Reverse Transcriptase Reactions using Acoustic Microstreaming

We describe a novel method for increasing cDNA yield from single-cell quantities of mRNA in otherwise standard laboratory reverse transcription reactions. The novelty resides in the use of a micromixer, which utilizes the phenomenon of acoustic microstreaming, to mix fluids at microliter scales more effectively than shaking, vortexing or trituration.

Correlating gene expression with cell behavior is ideally done at the single-cell level.  However, this is not easily achieved because the small amount of ...

increasing-cdna-yields-from-single-cell-quantities-mrna-standard

Research

JoVE Journal

Bioengineering

10.1K Views.  University of Melbourne. We describe a novel method for increasing cDNA yield from single-cell quantities of mRNA in otherwise standard laboratory reverse transcription reactions. The novelty resides in the use of a micromixer, which utilizes the phenomenon of acoustic microstreaming, to mix fluids at microliter scales more effectively than shaking, vortexing or trituration.