The authors acknowledge the ONR-MURI Award (NN00014-06-1-1176) and the U.S. Army Medical Research and Materiel Command (Grant No. W81XWH-10-1-0806) for financial support. This material is based upon work supported by the National Science Foundation under Grant No. EEC 0552584 and 0851519.

1. Combinatorial Polymer Library Synthesis (Varying in Polymer Chemistry) - see Figure 1 for Robotic Setup
<ol>
 <li>Dissolve each monomer in the appropriate solvent (concentration = 25 mg/ml) and load each into a 10cc gas tight syringe.</li>
 <li>Attach the solvent resistant lure lock capillary tubes to the end of each syringe.</li>
 <li>Place the syringes on the syringe pumps (New Era Programmable Syringe Pumps) and lock into position.</li>
 <li>Set the linear actuators (Zaber) to the starting position.</li>
 <li>Using ring stand clamps, position the end of both capillary tubes into the starting vial/well for monomer deposition.</li>
 <li>Initiate the LabVIEW program, which pumps variable volumes of each monomer into each well depending upon the desired copolymer composition. This is achieved in the program by instructing the Z-axis actuator to lower the capillary tubes into the vial/well and then each pump to dispense the desired volume. Next, the program instructs the Z-actuator to return to its home position and the X- and Y- actuators to move to the position of the next vial/well. This is carried out until each well has the desired volume of monomer deposited into it.</li>
 <li>Following monomer deposition, the multi-well or multi-vial monomer library is transferred to a pre-heated vacuum oven and incubated under vacuum for the duration of the condensation polymerization reaction. For CPH:SA synthesis the reaction is carried out at 180 &deg;C, 0.3 torr, for 1.5 hr but these reaction conditions will vary between different polymer systems.</li>
</ol>
2. Combinatorial Blank and Protein-loaded Polymer Nanoparticle and Film Library Fabrication - see Figure 1 for Robotic Setup
<ol>
 <li>The syringe in the first programmable syringe pump is filled with a solvent (blank library) or a solvent with protein dispersed in it (protein-loaded library) while the syringe in the second syringe pump is left empty. Tubes for nanoparticle fabrication in the adjacent sample holder are filled with the non-solvent (ratio of solvent to non-solvent is 1 to 100). For film fabrication an empty multi-well plate is utilized in place of the tubes in the adjacent sample holder.</li>
 <li>Using the LabVIEW program, the solvent is deposited into all polymer vials/wells of the library (concentration = 20 mg/ml) and incubated for 1-5 min. An optional sonication step (30 s at 40 Hz) can be introduced to ensure complete polymer dissolution.</li>
 <li>Next, by initiating a separate LabVIEW program, the sample is withdrawn into the empty syringe, and deposited into its corresponding tube of non-solvent (nanoparticles) or empty well (films) in the adjacent sample holder.</li>
 <li>This process is carried out for each composition of the discrete polymer library.</li>
 <li>The nanoparticle or film library is then placed in a vacuum chamber for solvent and non-solvent removal (the nanoparticle library can also be recovered using vacuum filtration).</li>
</ol>
3. High-throughput Protein Release Kinetics
<ol>
 <li>For investigating high-throughput protein release kinetics from a polymer library, a 96 deep-welled (2 ml/well), polypropylene plate is modified such that the top 1/3 of the well wall in neighboring columns (ex: A and B, C and D, E and F, G and H) is removed to adjoin the wells. The protein-loaded films must be fabricated in or the nanoparticles transferred into this plate to perform high-throughput release kinetics studies. Protein-loaded nanoparticle or film samples must only be placed in one well of the adjoining columns (ex: A, C, E, and G). See Figure 4 for details.</li>
 <li>Following the transfer of the nanoparticles to the 96 deep-welled release plate, the particles are allowed to settle. PBS buffer (0.1 mM, pH 7.4) is slowly added to each sample well (columns A, C, E and G) and then to each neighboring well (columns B, D, F, and H) until the wells are full and the buffer is free flowing between adjoining wells. For nanoparticles, this process needs to be carried out with extra caution to ensure the particles remain at the bottom of the sample well (columns A, C, E and G) and not transferred into the adjoining release well (columns B, D, F, and H). In some cases, centrifugation is required to localize the nanoparticle samples at the bottom of the sample well (columns A, C, E and G).</li>
 <li>Next, the release plate is sealed with a lid and placed at the desired temperature (i.e. 37 &deg;C) under agitation for the duration of the experiment.</li>
 <li>At incremental time points (i.e. 0.04, 1, 2, 3, 5, 7, 9, 12, 15, 19, 24, and 30 days) the amount of released fluorochrome-conjugated protein is quantified using a 9,400 Typhoon Flatbed Fluorescent Scanner (GE Healthcare). The release plate is placed on the scanner surface, scanned using the appropriate excitation laser and emission filters, and the fluorescence intensity of the released protein in the release wells (columns B, D, F and H) is quantified (Image Quant). It is suggested that protein standards of known concentrations be included in the well plate for calculating protein quantity and accounting for fluorochrome quenching.</li>
</ol>
4. Representative Results
Upon fabrication of the polymer library, characterization has been carried out with 1H NMR, GPC, and FTIR to validate this combinatorial method1,7,8,11. Molecular weights range from 10,000-20,000 g/mol, polydispersity index ranges from 1.5-3.0, and chemical composition has been shown to be accurate and in agreement with conventional methods of polyanhydride synthesis12-15. Similarly, SEM images of the nanoparticles libraries showed similar surface morphology, size, and size distribution as that of conventionally fabricated nanoparticles2. Protein release kinetics from polyanhydride nanoparticles or films is carried out in a modified well plate as described previously1. The results revealed an approximate zero order release with or without a burst dependent upon protein loading and polymer chemistry (Figures 2 and 3) 1,12,14,16.
<img alt="Figure 1" src="/files/ftp_upload/3882/3882fig1.jpg" /> 
Figure 1. Combinatorial polymer film and nanoparticle fabrication apparatus.
<img alt="Figure 2" src="/files/ftp_upload/3882/3882fig2.jpg" /> 
Figure 2. High-throughput release of Texas Red bovine serum albumin (TRBSA) from a CPH:SA polymer nanoparticle library. SA-rich polymer chemistries release encapsulated TRBSA the most rapidly, whereas CPH-rich polymer chemistries release the slowest. Error bars represent standard deviation and n=4. Reprinted with permission from Petersen et. al.1. Copyright 2010 American Chemical Society. 
 
<img alt="Figure 3" src="/files/ftp_upload/3882/3882fig3.jpg" /> 
Figure 3. High-throughput release of Texas Red bovine serum albumin (TRBSA) from a CPTEG:CPH polymer film library. CPTEG-rich polymer chemistries release encapsulated TRBSA the most rapidly, whereas CPH-rich polymer chemistries release the slowest. Error bars represent standard deviation and n=3.
<img alt="Figure 4" src="/files/ftp_upload/3882/3882fig4.jpg" /> 
Figure 4. Image showing two neighboring wells "before" and "after" modification in the 96 deep-welled polypropylene plate. The "after" modification image on the right also depicts the addition of a polymer film (bottom of left well) with an encapsulated fluorescent molecule being released between the two wells into a buffer solution. The released fluorescent molecule is then detected in the right well.

<ol>
	<li>Petersen, L. K., Sackett, C. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel,+high-throughput+method+to+study+in+vitro+protein+release+from+polymer+nanospheres.">A novel, high-throughput method to study in vitro protein release from polymer nanospheres.</a> J. Comb. Chem. 12, 51-56 (2010).</li><li>Petersen, L. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Activation+of+innate+immune+responses+in+a+pathogen-mimicking+manner+by+amphiphilic+polyanhydride+nanoparticle+adjuvants.">Activation of innate immune responses in a pathogen-mimicking manner by amphiphilic polyanhydride nanoparticle adjuvants.</a> Biomaterials. 32, 6815-6822 (2011).</li><li>Vogel, B. M., Cabral, J. T., Eidelman, N., Narasimhan, B., Mallapragada, S. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Parallel+synthesis+and+high-throughput+dissolution+testing+of+biodegradable+polyanhydride+copolymers.">Parallel synthesis and high-throughput dissolution testing of biodegradable polyanhydride copolymers.</a> J. Comb. Chem. 7, 921-928 (2005).</li><li>Petersen, L. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-throughput+evaluation+of+in+vivo+biodistribution+of+polyanhydride+nanoparticles.">High-throughput evaluation of in vivo biodistribution of polyanhydride nanoparticles.</a> Adv. Healthcare Mater. , (2012).</li><li>Petersen, L. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Combinatorial+design+of+biomaterials+for+drug+delivery:+opportunities+and+challenges.">Combinatorial design of biomaterials for drug delivery: opportunities and challenges.</a> Expert Opin. Drug Deliv. 5, 837-846 (2008).</li><li>Petersen, L. K., Oh, J., Sakaguchi, D. S., Mallapragada, S. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Amphiphilic+polyanhydride+films+promote+neural+stem+cell+adhesion+and+differentiation.">Amphiphilic polyanhydride films promote neural stem cell adhesion and differentiation.</a> Tissue Eng. 17, 2533-2541 (2011).</li><li>Petersen, L. K., Sackett, C. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-throughput+analysis+of+protein+stability+in+polyanhydride+nanoparticles.">High-throughput analysis of protein stability in polyanhydride nanoparticles.</a> Acta Biomater. 6, 3873-3881 (2010).</li><li>Petersen, L. K., Xue, L., Wannemuehler, M. J., Rajan, K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+simultaneous+effect+of+polymer+chemistry+and+device+geometry+on+the+in+vitro+activation+of+murine+dendritic+cells.">The simultaneous effect of polymer chemistry and device geometry on the in vitro activation of murine dendritic cells.</a> Biomaterials. 30, 5131-5142 (2009).</li><li>Thorstenson, J. B., Petersen, L. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Combinatorial/high-throughput+methods+for+the+determination+of+polyanhydride+phase+behavior.">Combinatorial/high-throughput methods for the determination of polyanhydride phase behavior.</a> J. Comb. Chem. 11, 820-828 (2009).</li><li>Xue, L., Petersen, L., Broderick, S., Narasimhan, B., Rajan, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Identifying+factors+controlling+protein+release+from+combinatorial+biomaterial+libraries+via+hybrid+data+mining+methods.">Identifying factors controlling protein release from combinatorial biomaterial libraries via hybrid data mining methods.</a> ACS Comb. Sci. 13, 50-58 (2011).</li><li>Adler, A. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-throughput+cell-based+screening+of+biodegradable+polyanhydride+libraries.">High-throughput cell-based screening of biodegradable polyanhydride libraries.</a> Comb. Chem. High Through. Screen. 12, 634-645 (2009).</li><li>Determan, A. S., Trewyn, B. G., Lin, V. S., Nilsen-Hamilton, M., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Encapsulation,+stabilization,+and+release+of+BSA-FITC+from+polyanhydride+microspheres.">Encapsulation, stabilization, and release of BSA-FITC from polyanhydride microspheres.</a> J. Control. Release. 100, 97-109 (2004).</li><li>Determan, A. S., Wilson, J. H., Kipper, M. J., Wannemuehler, M. J., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Protein+stability+in+the+presence+of+polymer+degradation+products:+consequences+for+controlled+release+formulations.">Protein stability in the presence of polymer degradation products: consequences for controlled release formulations.</a> Biomaterials. 27, 3312-3320 (2006).</li><li>Torres, M. P., Determan, A. S., Anderson, G. L., Mallapragada, S. K., Narasimhan, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Amphiphilic+polyanhydrides+for+protein+stabilization+and+release.">Amphiphilic polyanhydrides for protein stabilization and release.</a> Biomaterials. 28, 108-116 (2007).</li><li>Torres, M. P., Vogel, B. M., Narasimhan, B., Mallapragada, S. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synthesis+and+characterization+of+novel+polyanhydrides+with+tailored+erosion+mechanisms.">Synthesis and characterization of novel polyanhydrides with tailored erosion mechanisms.</a> J. Biomed. Mater. Res. A. 76, 102-110 (2006).</li><li>Carrillo-Conde, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Encapsulation+into+amphiphilic+polyanhydride+microparticles+stabilizes+Yersinia+pestis+antigens.">Encapsulation into amphiphilic polyanhydride microparticles stabilizes Yersinia pestis antigens.</a> Acta Biomater. 6, 3110-3119 (2010).</li></ol>

No conflicts of interest declared.

Knowledge of the necessary synthesis conditions and the glass transition temperatures (Tgs) of the polymers being synthesized are essential for library fabrication. If the Tgs are below room temperature, the nanoparticle fabrication step may need to be carried out in a controlled temperature environment below the Tg of the polymers. Additionally, caution should be taken to ensure that all equipment that comes in contact with high temperatures and the solvents must be fit to handle those c...

<table border="1">
	<tbody>
 <tr>
 <td>Name</td>
 <td>Company</td>
 <td>Catalog number</td>
 </tr>
 <tr>
 <td>Motorized XYZ Stage: 3x T-LSM050A, 50 mm travel per axis</td>
 <td>Zaber Technologies</td>
 <td>T-XYZ-LSM050A-KT04</td>
 </tr>
 <tr>
 <td>NE-1000 Single Syringe Pump</td>
 <td>New Era Pump Systems</td>
 <td>NE-1000</td>
 </tr>
 <tr>
 <td>Pyrex* Vista* Rimless Reusable Glass Culture Tubes</td>
 <td>Corning</td>
 <td>07-250-125</td>
 </tr>
 <tr>
 <td>Glass cuvettes</td>
 <td>Scientific Strategies</td>
 <td>G102</td>
 </tr>
 <tr>
 <td>LabVIEW</td>
 <td>National Instruments</td>
 <td>776671-35</td>
 </tr>
 <tr>
 <td>SGE Gas Tight Syringes, Luer Loc</td>
 <td>Sigma Aldrich</td>
 <td>509507</td>
 </tr>
 <tr>
 <td>U96 DeepWell Plates 1.3 ml &amp; 2.0 ml</td>
 <td>Thermo Scientific: Nunc</td>
 <td>278743</td>
 </tr>
 <tr>
 <td>Well cap mats</td>
 <td>Thermo Scientific: Nunc</td>
 <td>276000</td>
 </tr>
 <tr>
 <td>Typhoon 9400</td>
 <td>GE Healthcare</td>
 <td>63-0055-79</td>
 </tr>
 <tr>
 <td>Whatman Grade 50 Circles 90 mm</td>
 <td>Whatman</td>
 <td>1450-090</td>
	 </tr>
	 </tbody>	
 </table>

combinatorial synthesis of and high-throughput protein release from polymer film and nanoparticle libraries

Polyanhydrides are a class of biomaterials with excellent biocompatibility and drug delivery capabilities. While they have been studied extensively with conventional one-sample-at-a-time synthesis techniques, a more recent high-throughput approach has been developed enabling the synthesis and testing of large libraries of polyanhydrides1. This will facilitate more efficient optimization and design process of these biomaterials for drug and vaccine delivery applications. The method in this work describes the combinatorial synthesis of biodegradable polyanhydride film and nanoparticle libraries and the high-throughput detection of protein release from these libraries. In this robotically operated method (Figure 1), linear actuators and syringe pumps are controlled by LabVIEW, which enables a hands-free automated protocol, eliminating user error. Furthermore, this method enables the rapid fabrication of micro-scale polymer libraries, reducing the batch size while resulting in the creation of multivariant polymer systems. This combinatorial approach to polymer synthesis facilitates the synthesis of up to 15 different polymers in an equivalent amount of time it would take to synthesize one polymer conventionally. In addition, the combinatorial polymer library can be fabricated into blank or protein-loaded geometries including films or nanoparticles upon dissolution of the polymer library in a solvent and precipitation into a non-solvent (for nanoparticles) or by vacuum drying (for films). Upon loading a fluorochrome-conjugated protein into the polymer libraries, protein release kinetics can be assessed at high-throughput using a fluorescence-based detection method (Figures 2 and 3) as described previously1. This combinatorial platform has been validated with conventional methods2 and the polyanhydride film and nanoparticle libraries have been characterized with 1H NMR and FTIR. The libraries have been screened for protein release kinetics, stability and antigenicity; in vitro cellular toxicity, cytokine production, surface marker expression, adhesion, proliferation and differentiation; and in vivo biodistribution and mucoadhesion1-11. The combinatorial method developed herein enables high-throughput polymer synthesis and fabrication of protein-loaded nanoparticle and film libraries, which can, in turn, be screened in vitro and in vivo for optimization of biomaterial performance.

Watch this Scientific Journal Video about Combinatorial Synthesis of and High-throughput Protein Release from Polymer Film and Nanoparticle Libraries at JoVE.com

Combinatorial Synthesis of and High-throughput Protein Release from Polymer Film and Nanoparticle Libraries

This method describes the combinatorial synthesis of biodegradable polyanhydride film and nanoparticle libraries and the high-throughput detection of protein release from these libraries.

Polyanhydrides are a class of biomaterials with excellent biocompatibility and drug delivery capabilities. While they have been studied extensively with ...

combinatorial-synthesis-high-throughput-protein-release-from-polymer

Research

JoVE Journal

Bioengineering

10.3K Views.  Iowa State University. This method describes the combinatorial synthesis of biodegradable polyanhydride film and nanoparticle libraries and the high-throughput detection of protein release from these libraries.