We thank Barbara Windschiegl for her help in establishing SOPs; Dennis Remme for his work on the NanoCalcFX software and Alina Kollmannsperger, Markus Braner and Milan Gerovac for helpful suggestions on the manuscript. The German-Israeli Project Cooperation (DIP) provided by the DFG and the Federal Ministry of Education and Research to R.T., as well as the Federal Ministry of Economics and Technology (ZIM R&amp;D Project) to R.T. and Nanospot GmbH supported this work.

1. Preparation of Large Unilamellar Vesicles (LUVs)
<ol>
	<li>Clean a round bottom flask (10 ml volume) with nitrogen gas to remove any dust particles. Rinse the round bottom flask with ethanol. 
	Note: Residual ethanol can be tolerated and does not disturb subsequent steps.</li>
	<li>Wash a 1 ml glass syringe 4x with chloroform, to remove any contamination. Add 4 ml SoyPC20 (25 mg/ml in chloroform) to the round bottom flask and dope the lipid solution with an additional DOPEATTO390 to a final concentration of 0.1 mol%. 
	Note: Instead of DOPEATTO390 other fluorophore-labeled lipids or lipophilic dyes can also be used, depending on available excitation sources.</li>
	<li>Connect the round bottom flask to a rotary evaporator. Dry the lipid film for 40 min at 300 mbar, 30 &#176;C water bath temperature and maximal rotation speed, to form a homogenous lipid film on the glass wall of the flask.</li>
	<li>Transfer the flask to a high vacuum pump and dry the lipid film for additional 30 min at room temperature.</li>
	<li>Add 5 ml buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) and 8 glass beads (2.7-mm diameter, ethanol washed and dried) to the flask. Connect the flask to the rotary evaporator and rotate without vacuum at 50 &#176;C at maximum speed. 
	Note: Glass beads mechanically displace the lipid film from the glass wall, leading to (multilamellar) vesicle formation. After 45 min rotation the solution appears milky and no residual lipid film should be visible at the flask walls. Instead of glass beads other methods like sonicating the flask in a water bath sonifier, vortexing the flask or the gentle rehydration method are also applicable.</li>
	<li>Transfer the flask under inert gas (argon) to an ultrasonic bath and sonicate for 4 min at room temperature. 
	Note: The ultrasound shockwaves disrupt the liposomes, making them unilamellar.</li>
	<li>Split the LUV solution into 1 ml aliquots.</li>
	<li>Perform 5 freeze/thaw cycles by freezing the LUV solution in liquid nitrogen, followed by thawing at 40 &#176;C in a water bath. 
	Note: This leads to rupture and spontaneous rearrangement of individual liposomes with each other, leading to size increase.</li>
	<li>At the last freezing step store all samples at -80 &#176;C. 
	Note: The LUVs will be stable for at least 6 months.</li>
</ol>
2. Protein Reconstitution
<ol>
	<li>Thaw 1 ml LUV aliquot on ice. Directly before reconstitution, extrude liposomes 17x through a 400 nm polycarbonate filter membrane using a mini extruder. 
	Note: Lipid aggregates will be removed and the final homogenous size distribution is reached.</li>
	<li>Destabilize LUVs by addition of 4% Triton X-100 (v/v) to a final concentration of 0.25% (v/v) and incubate for 5 min at 50 &#176;C. 
	Note: The amount of liposomes used in this step depends on the mass of the purified MscLG22C used (see step 2.3). Purify MscLG22C (derived from E. coli) as described in detail in 28.</li>
	<li>Mix purified MscLG22C and detergent-saturated liposomes at 1:20 (w/w) ratio and incubate for additional 30 min at 50 &#176;C.</li>
	<li>For detergent removal add bio-beads in Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) to the protein/liposome solution, with 16 mg (wet weight) bio-beads per &#181;l detergent used to destabilize liposomes in step 2.2.</li>
	<li>Perform detergent removal overnight (16 hr) at 4 &#176;C on a rotating plate. 
	Note: The constant mixing of the solution ensures optimal detergent removal.</li>
	<li>After detergent removal store proteoliposomes at 4 &#176;C and use for experiments on the same day.</li>
</ol>
3. Activity Assay
<ol>
	<li>During protein reconstitution take a 100 &#181;l aliquot of detergent-destabilized proteoliposome solution after finishing step 2.3.</li>
	<li>Add 1 volume of calcein (30 mM) to the protein-liposome solution and incubate additional 5 min at 50 &#176;C.</li>
	<li>Remove detergent from the solution as described in step 2.4 - 2.6.</li>
	<li>After detergent removal equilibrate a size-exclusion column (20 ml bed volume or more) with Tris buffer (3x the bed volume). 
	Note: Proteoliposome separation can be performed at room temperature, however keeping the sample constantly at 4 &#176;C is advised to ensure best protein activity after fractionation.</li>
	<li>Separate proteoliposomes from free calcein by applying the entire aliquot (200 &#181;l) to the size exclusion column. Allow the mixture to soak into the column, followed by elution of the proteoliposomes from the column via continuous buffer application on top using gravity flow. Observe the calcein containing proteoliposomes as a discrete orange band in the elution front. Collect fractions of 500 &#181;l respectively. 
	Note: Free calcein dye will elute after the proteoliposome fraction with complete separation.</li>
	<li>Pipette 80 &#181;l of each fraction onto a micro-well plate for fluorescent read-out and identify the fraction containing the highest amount of calcein containing proteoliposomes via fluorescence emission. Detect fluorescence at 520 nm with excitation at 490 nm. Use the proteoliposome fraction with the highest signal for the following activity assay.</li>
	<li>Mix 20 &#181;l of the proteoliposome-containing fraction with 980 &#181;l Tris buffer in a 1 ml fluorescence cuvette.</li>
	<li>Measure fluorescence emission at 520 nm (excitation 490 nm) using a spectrofluorometer. Record for 1 min and then add 25 &#181;l of MTSET ([2-(trimethylammonium)ethyl]methanethiosulfonate) from a stock solution (160 mM) and mix well. Keep on recording during mixing. Always prepare the stock solution fresh directly before use. 
	Note: Once solved in buffer MTSET hydrolyzes within 30 min and will be non-reactive. MTSET can be weighed and kept as dry powder aliquot at -20 &#176;C until use. 
	Note: Once activated the MscLG22C channel opens and releases the entrapped calcein, leading to a local concentration decrease of the calcein when effluxing the proteoliposomes and subsequent dequenching of the dye, resulting in an increase of the fluorescence emission.</li>
	<li>After the fluorescence emission has reached a stable plateau again, solubilize the liposomes by addition of 50 &#181;l Triton X-100 (4% v/v). 
	Note: Ideally no further fluorescence increase can be observed, implying active protein in every liposome.</li>
</ol>
4. Size Distribution Measurement of LUVs Using Nano-particle Tracking
<ol>
	<li>Note that only minimal samples of the liposome or proteoliposome solution are necessary for size distribution analysis using the nanoparticle tracker. Dilute a liposome solution of 5 mg/ml lipid concentration 1:5,000 (v/v) in buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) for analysis to a final volume of 1 ml. Filter all buffers used for dilution and prior LUV preparation and reconstitution using a 0.2 &#181;m membrane to remove any suspended particles like dust that would disturb size distribution measurements.</li>
	<li>Wash the flow-chamber with ultra-pure water.</li>
	<li>Use the surface markers to focus on the light beam. Inject approximately 300 &#181;l of the diluted liposome sample and immediately close the exit valve to stop the flow inside the flow chamber, without introducing any air bubbles.</li>
	<li>Adjust focus and camera shutter/gain settings to ensure adequate scattering signal of the sample for detection. 
	Note: 20 - 80 signals should be clearly visible in the field of view. Prevent overcrowding (&#62; 80 signals) as the software will not be able to track individual signals when overlapping.</li>
	<li>Go to the &#34;Capture&#34; screen. Adjust the temperature control to 25 &#176;C and the capture duration to 90 sec using the software controls. Press &#34;Record&#34; to start recording a time series. 
	Note: Upon completion of the time series a new window opens.</li>
	<li>Save the time series in the given format (*.avi). For practical reasons during batch analysis save all files in a single folder.</li>
	<li>Open the exit valve and inject another 300 &#181;l into the flow chamber. Close the valve and repeat steps 4.3 - 4.6 twice.</li>
	<li>After completing all sample runs wash the flow chamber with 5 ml ultra-pure water. Go to the &#34;Pre-Process&#34; screen. Set the calibration parameters temperature = 25 &#176;C and viscosity = 0.91 for the Tris buffer used in this protocol.</li>
	<li>Open the batch process window and load the recorded time series (Advanced/Batch Process/Set File 1-3). Press &#34;GO&#34; to start the size distribution analysis. 
	Note: the analytical software automatically tracks the single particles and calculates their diameter based on their movement behavior using the parameters set in step 4.8. 
	Note: The resulting size distribution analysis saves automatically into the same folder as the time series files.</li>
	<li>Additionally create a report file to summarize the results (Export/Create Report PDF).</li>
</ol>
5. Chip Holder Preparation
<ol>
	<li>Weigh 1.0 g of MDX4 medical grade elastomer base and 0.1 g MDX4 curing agent into a 50 ml reaction tube. Blend both thoroughly with a glass bar.</li>
	<li>Put the tube into a desiccator for 1 hr to degas the adhesive. Afterwards use it within 30 min for chip gluing, as the adhesive will harden and be too hard to work with.</li>
	<li>During elastomer degassing (step 5.1) clean an objective glass slide thoroughly with chloroform to remove any contaminations before chip bonding. Rinse the slide with 5 ml of chloroform using a glass syringe. Collect the chloroform in an underneath positioned beaker. After washing let the slide dry. 
	Note: Perform this step under a fume hood. Alternative to chloroform, other organic solvents like acetone can also be used.</li>
	<li>Deposit a small amount of the adhesive bonding material onto the cover glass using a pipette tip (crystal tips for 10 &#181;l pipettes). Remember that the chips have to fit into the 8-chamber slide holder later on and have to be placed on the slide accordingly.</li>
	<li>Carefully remove one chip at a time from the wafer board using fine tip tweezers and deposit the chip on the drop of adhesive on the cover glass. Ensure that the coated side of the chip faces upwards.</li>
	<li>Gently push the chip onto the cover glass with the back of a blunt PE tweezers. To ensure that the glue is dispensed evenly underneath the chip, carefully slide the chip forth and back. CRITICAL STEP: Ensure that no air bubbles are trapped underneath the chip, as it will disturb optical imaging of the chip cavities later on. Also ensure that no adhesive material contaminates the chip surface.</li>
	<li>Desiccate the finished cover glass for 2 hr at 65 &#176;C in a cabinet dryer. 
	Note: Chips are still coated with a protective layer originating from their fabrication that needs to be removed.</li>
	<li>To remove the protective layer, perform a sequential solvent washing step. During the curing of chips, preheat a water bath to 54 &#176;C.</li>
	<li>Place 3 glass beakers into the water bath, two of them filled with isopropanol and one filled with acetone.</li>
	<li>Insert the chip cover glass into a slide holder and submerge it into the first isopropanol filled dish for 10 min. Afterwards transfer it to the acetone filled dish, incubate again for 10 min before transferring it for the final washing step to the second isopropanol dish and incubate another 10 min.</li>
	<li>Remove the slide holder from the dish and carefully wash it extensively with ultrapure water, followed by drying the chips with a gentle stream of nitrogen gas.</li>
	<li>Take-off the lamination sheet from the 8-well sticky-slide and put it backwards on the bench. Carefully pick up the cover slide and gently press onto the sticky-slide with the chips facing the wells. Let the finished chip holder rest for a couple of minutes before use.</li>
</ol>
6. Assay Preparation
Note: Nanopore chips glued to a cover glass and separated by an 8-well sticky-slide possess the benefit, that multiple chips can be addressed in a single experimental run, with chips being completely separated from each other.
<ol>
	<li>After chip holder preparation, rinse each chip with pure ethanol and blow dry with nitrogen gas, to remove any contaminations like dust.</li>
	<li>Clean the chip surface with air, oxygen or nitrogen plasma. Depending on the type of plasma cleaning time-periods vary: perform oxygen plasma treatment for 1 min, air and nitrogen plasma for 5 min at 0.3 mbar at 80% power setting (RF power medium or high).</li>
	<li>After plasma cleaning incubate chips in pure ethanol for 10-15 min to ensure cavity wetting.</li>
	<li>Stepwise exchange ethanol for buffer by adding 400 &#181;l of Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered), followed by mixing of the solution without introducing air bubbles and subsequent removal of 400 &#181;l. Repeat this procedure 12 times, to ensure ethanol removal. 
	Note: Ethanol would be harmful for liposomes and suspended lipid bilayers.</li>
	<li>Dope Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) with 5 mM CaCl2 and 1 &#181;M Oy647 dye. Completely remove the washing buffer from the chip and immediately add the doped buffer to the chip. Note: Chips will be covered with a thin buffer film after wash buffer removal, so the chip is not in direct contact with air, ensuring a constant wetting of the cavities and the chip surface.</li>
	<li>Add 1 mg/ml LUVs or proteo-LUVs in Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) to each well. 
	Note: The final volume in each well is 300 &#181;l. Consider subsequent additions of the control dye and the chemical modifier MTSET during doped Tris buffer addition.</li>
	<li>For pore-spanning lipid bilayer formation on the chip surface incubate the chip for 1 hr at room temperature with the liposome solution. Afterwards wash each chip with 4x 400 &#181;l of Ca2+-free Tris buffer.</li>
	<li>Add the control dye to each well, with a final concentration of 5 &#181;M. The chips are now ready for the translocation assay.</li>
</ol>
7. Assay Setup
<ol>
	<li>Mount the chip holder to the epifluorescence microscope (20X air objective, long working distance). Focus on the rim of the nanopore chip to more easily find the focal plane of the micro-cavities. Once the cavities are in focus scan the nanopore array for a region that displays highest sealing ratio. 
	Note: Every inverted epifluorescence microscope can be used to perform chip assays. Depending on the objective magnification (20X - 60X) the number of assayed cavities will vary, with up to 9,000 cavities in a single field of view using 20X magnification. Air objectives with a long working distance are preferable. The use of inverted confocal laser scanning microscopes (CLSM) is also possible, but image acquisition might be the limiting factor due to the limited depth of focus.</li>
	<li>Optimize the chip illumination. 
	Note: Ensure that both dye channels do not exceed the maximum grey scale value, as changes cannot be observed. For export experiments adjust illumination of the translocated dye to 90% of maximum signal capacity. Adjust the control dye in open cavities to 80-90% of maximum signal capacity to clearly detect any leaky membrane sealing.</li>
	<li>Once all channels are adjusted start the time series. Take images every 10-20 sec for 90 min. 
	Note: This is adequate to likewise follow specific and unspecific efflux events.</li>
	<li>Initialize efflux of the fluorescent substrate by the addition of cysteine-specific, positively charged compound MTSET to a final concentration of 3 mM. Allow at least 5 min of experiment runtime before MTSET addition to be able to later on establish a stable fluorescent signal baseline prior to channel opening. Always prepare MTSET solution fresh directly before usage.</li>
</ol>
8. Data Analysis
<ol>
	<li>Open the time series image stack with a standard version of ImageJ (File/Import/Image Sequence).</li>
	<li>If fluorescent channels are stacked, split the channels in individual stacks for each channel (Image/Stacks/Stack to Images).</li>
	<li>Duplicate the first image of the translocation substrate channel for ROI (regions of interest) identification (Image/Duplicate).</li>
	<li>Convert the image to a binary image (Image/Adjust/Threshold). Ensure that the algorithm used depicts signals for all sealed cavities without overlapping pixilation.</li>
	<li>Automatically define regions of interest with the particle analyzer tool (Analyze/Analyze Particle). Define a minimum particle size defined, to avoid particle noise. Check the options &#34;exclude on edges&#34; and &#34;include holes&#34;. Ensure that resulting ROIs reflect the microcavity array pattern. Interjacent ROIs are artifacts, therefore remove them. Save the ROI list. 
	Note: Measurement parameter has to be set to &#34;area&#34; before particle analysis (Analyze/Set Measurements/Area)</li>
	<li>Open the Time Series Analyzer plug-in (http://rsb.info.nih.gov/ij/plugins/time-series.html), which resizes all ROIs automatically to the same size. Re-size all existing ROIs to a width/height of 6x6 pixels and oval shape (Timer Series Analyzer/AutoROIProperties). Check the option &#34;Resize existing ROIS&#34;. Save the resulting resized ROI list.</li>
	<li>Open the ROI manager (Analyze/Tools/ROI Manager) and load the resized ROI list for each channel of the time series (ROI Manger/More/Open). ROIs will be superposed. To analyze the signal change for each ROI start the Multi Measure tool (ROI Manager/More/Multi Measure), select &#34;Measure all slices&#34; and &#34;One row per slice&#34; and start the multi measure. 
	Note: Measurement parameter has to be set to &#34;mean gray value&#34; for this step (Analyze/Set Measurements/Mean gray value)</li>
	<li>Save the resulting table, giving the mean grey value for each ROI in *.txt or *.xls format.</li>
	<li>Import the ROI analysis of each imaging channel into NanoCalcFX via the &#34;Import File&#34; option. Set &#34;Use first line for naming series&#34;. Set the step size between images according to the time series image acquisition periods and choose the corresponding column and decimal separator.</li>
	<li>Use the &#34;multiple sheet&#34; option to automatically correlate the graphs of the individual fluorescent channels. 
	Note: The events can now be analyzed and classified using the information given by the 3-color spectral information.</li>
	<li>Fit selected curves using the build-in fit function (fit option). 
	Note: The implemented efflux and influx equation is suitable for all monoexponential diffusion-driven events and fit boundaries can be set. Resulting rate constants can be plotted using the histogram tool or exported for further data refinement.</li>
</ol>

<ol><li>Yildirim, M. A., Goh, K. I., Cusick, M. E., Barabasi, A. L., Vidal, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Drug-target+network%5BTitle%5D)+AND+%22Nat+Biotechnol%22%5BJournal%5D)">Drug-target network.</a> Nat Biotechnol. 25, 1119(2007).</li>
<li>Hamill, O. P., Marty, A., Neher, E., Sakmann, B., Sigworth, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Improved+patch-clamp+techniques+for+high-resolution+current+recording+from+cells+and+cell-free+membrane+patches%5BTitle%5D)+AND+%22Pflugers+Arch%22%5BJournal%5D)">Improved patch-clamp techniques for high-resolution current recording from cells and cell-free membrane patches.</a> Pflugers Arch. 391, 85-100 (1981).</li>
<li>Osaki, T., Suzuki, H., Le Pioufle, B., Takeuchi, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Multichannel+simultaneous+measurements+of+single-molecule+translocation+in+%CE%B1-hemolysin+nanopore+array%5BTitle%5D)+AND+%22Anal.+Chem%22%5BJournal%5D)">Multichannel simultaneous measurements of single-molecule translocation in α-hemolysin nanopore array.</a> Anal. Chem. 81, 9866-9870 (2009).</li>
<li>Carrillo, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((High-resolution+membrane+capacitance+measurements+for+studying+endocytosis+and+exocytosis+in+yeast%5BTitle%5D)+AND+%22Traffic%22%5BJournal%5D)">High-resolution membrane capacitance measurements for studying endocytosis and exocytosis in yeast.</a> Traffic. , (2015).</li>
<li>Giacomini, K. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Membrane+transporters+in+drug+development%5BTitle%5D)+AND+%22Nat.+Rev.+Drug+Discov%22%5BJournal%5D)">Membrane transporters in drug development.</a> Nat. Rev. Drug Discov. 9, 215-236 (2010).</li>
<li>Castell, O. K., Berridge, J., Wallace, M. I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Quantification+of+membrane+protein+inhibition+by+optical+ion+flux+in+a+droplet+interface+bilayer+array%5BTitle%5D)+AND+%22Angew.+Chem.+Int.+Ed%22%5BJournal%5D)">Quantification of membrane protein inhibition by optical ion flux in a droplet interface bilayer array.</a> Angew. Chem. Int. Ed. 51, 3134-3138 (2012).</li>
<li>Zollmann, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Single+liposome+analysis+of+peptide+translocation+by+the+ABC+transporter+TAPL%5BTitle%5D)+AND+%22Proc.+Natl.+Acad.+Sci.+U.S.A%22%5BJournal%5D)">Single liposome analysis of peptide translocation by the ABC transporter TAPL.</a> Proc. Natl. Acad. Sci. U.S.A. 112, 2046-2051 (2015).</li>
<li>Tamm, L. K., McConnell, H. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Supported+phospholipid+bilayers%5BTitle%5D)+AND+%22Biophys.+J%22%5BJournal%5D)">Supported phospholipid bilayers.</a> Biophys. J. 47, 105-113 (1985).</li>
<li>Sackmann, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Supported+membranes%3A+scientific+and+practical+applications%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Supported membranes: scientific and practical applications.</a> Science. 271, 43-48 (1996).</li>
<li>Castellana, E. T., Cremer, P. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Solid+supported+lipid+bilayers%3A+From+biophysical+studies+to+sensor+design%5BTitle%5D)+AND+%22Surf.+Sci.+Rep%22%5BJournal%5D)">Solid supported lipid bilayers: From biophysical studies to sensor design.</a> Surf. Sci. Rep. 61, 429-444 (2006).</li>
<li>Wagner, M. L., Tamm, L. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Tethered+polymer-supported+planar+lipid+bilayers+for+reconstitution+of+integral+membrane+proteins%3A+silane-polyethyleneglycol-lipid+as+a+cushion+and+covalent+linker%5BTitle%5D)+AND+%22Biophys.+J%22%5BJournal%5D)">Tethered polymer-supported planar lipid bilayers for reconstitution of integral membrane proteins: silane-polyethyleneglycol-lipid as a cushion and covalent linker.</a> Biophys. J. 79, 1400-1414 (2000).</li>
<li>Naumann, C. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((The+polymer-supported+phospholipid+bilayer%3A+tethering+as+a+new+approach+to+substrate-membrane+stabilization%5BTitle%5D)+AND+%22Biomacromolecules%22%5BJournal%5D)">The polymer-supported phospholipid bilayer: tethering as a new approach to substrate-membrane stabilization.</a> Biomacromolecules. 3, 27-35 (2002).</li>
<li>Weiskopf, D., Schmitt, E. K., Klühr, M. H., Dertinger, S. K., Steinem, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Micro-BLMs+on+highly+ordered+porous+silicon+substrates%3A+Rupture+process+and+lateral+mobility%5BTitle%5D)+AND+%22Langmuir%22%5BJournal%5D)">Micro-BLMs on highly ordered porous silicon substrates: Rupture process and lateral mobility.</a> Langmuir. 23, 9134-9139 (2007).</li>
<li>Watanabe, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Arrayed+lipid+bilayer+chambers+allow+single-molecule+analysis+of+membrane+transporter+activity%5BTitle%5D)+AND+%22Nat.+Commun%22%5BJournal%5D)">Arrayed lipid bilayer chambers allow single-molecule analysis of membrane transporter activity.</a> Nat. Commun. 5, (2014).</li>
<li>Stamou, D., Duschl, C., Delamarche, E., Vogel, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Self-Assembled+Microarrays+of+Attoliter+Molecular+Vessels%5BTitle%5D)+AND+%22Angew.+Chem.+Int.+Ed%22%5BJournal%5D)">Self-Assembled Microarrays of Attoliter Molecular Vessels.</a> Angew. Chem. Int. Ed. 115, 5738-5741 (2003).</li>
<li>Lohr, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Single+Liposomes+Used+to+Study+the+Activity+of+Individual+Transporters%5BTitle%5D)+AND+%22Biophysical+Journal%22%5BJournal%5D)">Single Liposomes Used to Study the Activity of Individual Transporters.</a> Biophysical Journal. 106, 229a(2014).</li>
<li>Dunlop, J., Bowlby, M., Peri, R., Vasilyev, D., Arias, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((High-throughput+electrophysiology%3A+an+emerging+paradigm+for+ion-channel+screening+and+physiology%5BTitle%5D)+AND+%22Nat.+Rev.+Drug+Discov%22%5BJournal%5D)">High-throughput electrophysiology: an emerging paradigm for ion-channel screening and physiology.</a> Nat. Rev. Drug Discov. 7, 358-368 (2008).</li>
<li>Milligan, C. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Robotic+multiwell+planar+patch-clamp+for+native+and+primary+mammalian+cells%5BTitle%5D)+AND+%22Nat.+Protoc%22%5BJournal%5D)">Robotic multiwell planar patch-clamp for native and primary mammalian cells.</a> Nat. Protoc. 4, 244-255 (2009).</li>
<li>Soga, N., Watanabe, R., Noji, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Attolitre-sized+lipid+bilayer+chamber+array+for+rapid+detection+of+single+transporters%5BTitle%5D)+AND+%22Sci.+Rep%22%5BJournal%5D)">Attolitre-sized lipid bilayer chamber array for rapid detection of single transporters.</a> Sci. Rep. 5, (2015).</li>
<li>Kleefen, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Multiplexed+parallel+single+transport+recordings+on+nanopore+arrays%5BTitle%5D)+AND+%22Nano+Lett%22%5BJournal%5D)">Multiplexed parallel single transport recordings on nanopore arrays.</a> Nano Lett. 10, 5080-5087 (2010).</li>
<li>Wei, R., Gatterdam, V., Wieneke, R., Tampé, R., Rant, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Stochastic+sensing+of+proteins+with+receptor-modified+solid-state+nanopores%5BTitle%5D)+AND+%22Nat.+Nanotechnol%22%5BJournal%5D)">Stochastic sensing of proteins with receptor-modified solid-state nanopores.</a> Nat. Nanotechnol. 7, 257-263 (2012).</li>
<li>Urban, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Highly+parallel+transport+recordings+on+a+membrane-on-nanopore+chip+at+single+molecule+resolution%5BTitle%5D)+AND+%22Nano+Lett%22%5BJournal%5D)">Highly parallel transport recordings on a membrane-on-nanopore chip at single molecule resolution.</a> Nano Lett. 14, 1674-1680 (2014).</li>
<li>Kusters, I., Van Oijen, A. M., Driessen, A. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Membrane-on-a-Chip%3A+Microstructured+Silicon%2FSilicon-Dioxide+Chips+for+High-Throughput+Screening+of+Membrane+Transport+and+Viral+Membrane+Fusion%5BTitle%5D)+AND+%22ACS+Nano%22%5BJournal%5D)">Membrane-on-a-Chip: Microstructured Silicon/Silicon-Dioxide Chips for High-Throughput Screening of Membrane Transport and Viral Membrane Fusion.</a> ACS Nano. 8, 3380-3392 (2014).</li>
<li>Hansen, J. S., Thompson, J. R., Hélix-Nielsen, C., Malmstadt, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Lipid+directed+intrinsic+membrane+protein+segregation%5BTitle%5D)+AND+%22J.+Am.+Chem.+Soc%22%5BJournal%5D)">Lipid directed intrinsic membrane protein segregation.</a> J. Am. Chem. Soc. 135, 17294-17297 (2013).</li>
<li>Heinemann, F., Schwille, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Preparation+of+Micrometer-Sized+Free-Standing+Membranes%5BTitle%5D)+AND+%22ChemPhysChem%22%5BJournal%5D)">Preparation of Micrometer-Sized Free-Standing Membranes.</a> ChemPhysChem. 12, 2568-2571 (2011).</li>
<li>Lazzara, T. D., Carnarius, C., Kocun, M., Janshoff, A., Steinem, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Separating+attoliter-sized+compartments+using+fluid+pore-spanning+lipid+bilayers%5BTitle%5D)+AND+%22ACS+nano%22%5BJournal%5D)">Separating attoliter-sized compartments using fluid pore-spanning lipid bilayers.</a> ACS nano. 5, 6935-6944 (2011).</li>
<li>Winterhalter, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Black+lipid+membranes%5BTitle%5D)+AND+%22Curr.+Opin.+Colloid+Interface+Sci%22%5BJournal%5D)">Black lipid membranes.</a> Curr. Opin. Colloid Interface Sci. 5, 250-255 (2000).</li>
<li>Koçer, A., Walko, M., Feringa, B. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Synthesis+and+utilization+of+reversible+and+irreversible+light-activated+nanovalves+derived+from+the+channel+protein+MscL%5BTitle%5D)+AND+%22Nat.+Protoc%22%5BJournal%5D)">Synthesis and utilization of reversible and irreversible light-activated nanovalves derived from the channel protein MscL.</a> Nat. Protoc. 2, 1426-1437 (2007).</li>
</ol>

The authors declare no competing financial interests.

The technique presented here allows a highly parallel analysis of membrane protein transport. Reconstituted membrane protein systems can directly be applied to the biochip, making the adaption of theoretically every membrane transporter or channel possible. Transport analysis is only limited by the establishment of a fluorescent read-out system, either via direct fluorescence change (translocation of fluorophores or fluorescently labeled substrates) or indirect fluorescence change (pH-sensitive dyes, secondary enzymatic ...

The analysis of membrane proteins has become of increasing interest for basic and pharmaceutical research in the past 20 years. The development of novel drugs depends on the identification and detailed characterization of new targets, currently being one of the limiting factors. The fact that about 60% of all drug targets are membrane proteins1, makes the development of techniques to elucidate their function most important.
In the past, techniques for the study of electrogenic channels and transporters have been developed in multitude2-4. Non-electrogenic substrates in contrary present a more challenging task. They are however of special interest as prime drug targets, as they control the flux of solutes and nutrients across the cell membrane and function as key receptors in signaling cascades5.
Considerable effort has been put into the development of techniques to study the function of membrane transport proteins6,7. Systems using solid-supported membranes have emerged as most promising tools in this field8-10, including solid supported lipid bilayers, tethered bilayers11,12, microblack lipid membranes13,14 and native vesicle arrays15,16 to name a few. Some of them are even available as commercial setups17,18. Some examples have been published combining the ability to study single membrane proteins in a highly parallel manner14,19, a prerequisite for screening applications. However, these methods rarely bridge from basic research to the industrial environment. The difficulties often lie in the ability of the system to be automatable, the cost-intensive production and/or laborious preparation. An approach overcoming all the above mentioned obstacles is the final aim.
The technique presented here was developed to study membrane channels and transporters in vitro in a controlled environment on the single protein level20-22. Reconstitution of purified membrane proteins into LUVs is much more established than comparable approaches for GUVs23-26 or black lipid membranes27. They can directly be applied to the chip surface, where bilayer formation is taking place via a self-assembly process. The glass-bottom design of the nanoporous chip (Fig. 1) allows for air microscopy, which permits the straightforward automation of the system. In combination with a motorized stage multiple chips can be measured at the same time, with each field of view containing thousands of sealed cavities for analysis.
<img alt="Figure 1" src="/files/ftp_upload/53373/53373fig1.jpg" /> 
Figure 1. Design of multiplexed nanopore biochips. A) A silicon-on-insulator (SOI) wafer is structured by reactive-ion etching. Approximately 1,150 individual chips are fabricated from each wafer with identical properties and quality. B) Each chip comprises 250,000 individual microcavities with nano apertures. Scale bar: 200 &#181;m. C) Each cavity is addressable via multi-spectral fluorescence read-out. An intransparent top layer blocks the fluorescent signals from the buffer reservoir, making the biochip compatible with inverted fluorescence microscopes. D) Atomic force microscopy (AFM) imaging reveals evenly arranged pore openings and surface roughness of the silicon dioxide layer of 3.6 nm (n = 40) optimal for vesicle fusion. Scale bar: 5 &#181;m. E) Scanning electron microscopy (SEM) image shows a cross-section through the nanopore allowing access to the femtoliter cavities inside the silicon chip. This figure was reused with permission from 21. <a href="https://www.jove.com/files/ftp_upload/53373/53373fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
All data analysis is performed using freeware to guarantee unrestricted access for end users. Time series are analyzed using free image processing software and a custom build curve analysis software enabling batch processing and straightforward correlation of large datasets with multiple fluorescent channels and thousands of curves.
The model protein used in this protocol is the mechanosensitive channel of large conductance (MscL) channel protein derived from E. coli. It functions as a valve to release osmotic shock in nature, but was modified in such a way that rationally designed synthetic functionalities can covalently be attached to the channels constriction side. Via charge-repulsion of the covalently bound activator (MTSET) the channel is triggered to open, creating a nano-valve. Small molecules like ions, water, small proteins, but also small fluorophores can permeate through the channel. Here, the protein is used as a model to demonstrate the ability of the system to detect protein-mediated translocation.

<table><tbody><tr><td>&lt;strong&gt;Reagent&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>[2-(Trimethylammonium)ethyl]&lt;br/&gt; methanethiosulfonate</td><td>Toronto Research Chemicals Inc.</td><td>T792900</td><td>MTSET; hydrolized by water. Keep as dry pouder aliquot at -80 &amp;deg;C. Use immediately (30 minutes) after solubilization in buffer.</td></tr><tr><td>1 ml gas-tight syringe</td><td>Hamilton</td><td>#1001</td><td></td></tr><tr><td>10 ml round flask</td><td>Schott Duran</td><td></td><td></td></tr><tr><td>2.7 mm glas beads</td><td>Roth</td><td>N032.1</td><td></td></tr><tr><td>2-Propanole</td><td>Roth</td><td>9866.5</td><td></td></tr><tr><td>30 cm Luer-Lock Extension Tube</td><td>Sarstedt</td><td>744304</td><td></td></tr><tr><td>Acetone</td><td>Roth</td><td>5025.5</td><td></td></tr><tr><td>Bio-Beads SM-2 Adsorbent</td><td>Bio-Rad</td><td>152-3920</td><td>need to be activated before first use</td></tr><tr><td>CaCl&lt;sub&gt;2 &lt;/sub&gt;Dihydrat</td><td>Roth</td><td>HN04.3</td><td></td></tr><tr><td>Calcein</td><td>Sigma</td><td>C0875</td><td>store dark at -20 &amp;deg;C</td></tr><tr><td>Chloroform reagent grade</td><td>VWR Chemicals</td><td>22711324</td><td></td></tr><tr><td>DOPE&lt;sup&gt;ATTO390&lt;/sup&gt;</td><td>ATTO-TEC</td><td>AD 390-165</td><td>store dark at -20 &amp;deg;C</td></tr><tr><td>Ethanol absolute</td><td>Sigma-Aldrich</td><td>32205</td><td></td></tr><tr><td>Injekt Single-use syringe</td><td>Braun</td><td>460 60 51V</td><td></td></tr><tr><td>Injekt-F single-use syringe</td><td>Braun</td><td>91 66 017V</td><td></td></tr><tr><td>Keck clips</td><td>Schott</td><td>KC29</td><td></td></tr><tr><td>L-&amp;alpha;-Phosphatidylcholine, 20% (Soy)</td><td>Avanti Polar Lipids</td><td>5416016</td><td>store under inert gas at -20 &amp;deg;C</td></tr><tr><td>NaCl 99.5% p.a.</td><td>Roth</td><td>3957.2</td><td></td></tr><tr><td>Nanopore E100 wafer/chips</td><td>Micromotive (Mainz/Germany)</td><td></td><td>available on request</td></tr><tr><td>Nucleopore Track-Etch Membrane 0.4 &amp;micro;m</td><td>Whatman</td><td>800282</td><td></td></tr><tr><td>Oregon Green Dextran 488 (70 kDa)</td><td>life Technologies</td><td>D-7173</td><td>store dark at -20 &amp;deg;C</td></tr><tr><td>Oy647</td><td>Luminartis (M&amp;uuml;nster/Germany)</td><td>OY-647-T-1mg</td><td>store dark at -20 &amp;deg;C</td></tr><tr><td>Rotilabo-syringe filtration, unsterile, pore-size 0.22 &amp;micro;m</td><td>Roth</td><td>P 818.1</td><td></td></tr><tr><td>Sephadex G-50</td><td>Sigma-Aldrich</td><td>G5080</td><td>column material for size exclusion chromatography</td></tr><tr><td>Silastic MDX4-4210</td><td>Dow Corning</td><td></td><td>curing agent for chip fixation onto cover glass support</td></tr><tr><td>sticky-Slide 8-well</td><td>ibidi</td><td>80828</td><td>multi-well chamber for the mounting onto glass slides (chip holder)</td></tr><tr><td>Three-way stopcock blue</td><td>Sarstedt</td><td>744410001</td><td></td></tr><tr><td>Tris Pufferan 99.9% Ultra Quality</td><td>Roth</td><td>5429.2</td><td></td></tr><tr><td>Triton-X 100</td><td>Roth</td><td>6683.1</td><td></td></tr><tr><td>Whatman 0.2 &amp;micro;m cellulose nitrate membrane filter</td><td>Roth</td><td>NH69.1</td><td></td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;Equipment&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>B&amp;uuml;chi 461 water bath</td><td>B&amp;uuml;chi</td><td></td><td></td></tr><tr><td>B&amp;uuml;chi Rotavapor RE 111</td><td>B&amp;uuml;chi</td><td></td><td></td></tr><tr><td>Cary Eclipse Fluorescence Spectrophtometer&amp;nbsp;</td><td>Varian</td><td></td><td></td></tr><tr><td>LiposoFast Mini Extruder</td><td>Avestin</td><td></td><td></td></tr><tr><td>Membrane pump&amp;nbsp;</td><td>Vaccubrand</td><td>15430</td><td></td></tr><tr><td>Nanosight Nanoparticle Tracking Microscope</td><td>Malvern / Nanosight</td><td>LM 14C</td><td></td></tr><tr><td>NyONE microscope</td><td>Synentec</td><td></td><td>available on request</td></tr><tr><td>Pump control</td><td>Vaccubrand</td><td>CVC 2II</td><td></td></tr><tr><td>Sonicator bath Sonorex RK100H</td><td>Brandelin electronic</td><td>31200001107477</td><td></td></tr><tr><td>Vaccum pump RC5</td><td>Vaccubrand</td><td>1805400204</td><td></td></tr><tr><td>Water bath W13</td><td>Haake</td><td>002-9910</td><td></td></tr><tr><td>Plasma Cleaner PDC-37G</td><td>Harrick Plasma</td><td>PDC-37G</td><td></td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;Software&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>ImageJ</td><td>Open Source</td><td>http://imagej.nih.gov/ij/</td><td>scientific image processing software</td></tr><tr><td>NanoCalcFX</td><td>Freeware</td><td>http://sourceforge.net/projects/nanocalc/</td><td>data analysis/evaluation software for massive transport kinetic datasets</td></tr><tr><td>NTA 2.3 Analytical Software</td><td>Nanosight</td><td></td><td>data acquisition and analysis software for nanoparticle tracking microscope</td></tr><tr><td>NTA 2.3 Temperature Comms</td><td>Nanosight</td><td></td><td>temperature controle software for nanoparticle tracking microscope</td></tr></tbody></table>

membrane transport processes analyzed by a highly parallel nanopore chip system at single protein resolution

Membrane protein transport on the single protein level still evades detailed analysis, if the substrate translocated is non-electrogenic. Considerable efforts have been made in this field, but techniques enabling automated high-throughput transport analysis in combination with solvent-free lipid bilayer techniques required for the analysis of membrane transporters are rare. This class of transporters however is crucial in cell homeostasis and therefore a key target in drug development and methodologies to gain new insights desperately needed.
The here presented manuscript describes the establishment and handling of a novel biochip for the analysis of membrane protein mediated transport processes at single transporter resolution. The biochip is composed of microcavities enclosed by nanopores that is highly parallel in its design and can be produced in industrial grade and quantity. Protein-harboring liposomes can directly be applied to the chip surface forming self-assembled pore-spanning lipid bilayers using SSM-techniques (solid supported lipid membranes). Pore-spanning parts of the membrane are freestanding, providing the interface for substrate translocation into or out of the cavity space, which can be followed by multi-spectral fluorescent readout in real-time. The establishment of standard operating procedures (SOPs) allows the straightforward establishment of protein-harboring lipid bilayers on the chip surface of virtually every membrane protein that can be reconstituted functionally. The sole prerequisite is the establishment of a fluorescent read-out system for non-electrogenic transport substrates.
High-content screening applications are accomplishable by the use of automated inverted fluorescent microscopes recording multiple chips in parallel. Large data sets can be analyzed using the freely available custom-designed analysis software. Three-color multi spectral fluorescent read-out furthermore allows for unbiased data discrimination into different event classes, eliminating false positive results.
The chip technology is currently based on SiO2 surfaces, but further functionalization using gold-coated chip surfaces is also possible.

Pore-spanning membranes can easily be created on the nanostructured chip surface in a self-assembled manner. However the underlying process is still delicate and influenced by many parameters like liposome size, monodispersity of the liposome population, lamellarity, lipid- and salt-concentration and chemical surface properties. Most of these parameters have been carefully characterized and standardized in the above protocol. Other parameters however should be checked during every new pre...

Watch this Scientific Journal Video about Membrane Transport Processes Analyzed by a Highly Parallel Nanopore Chip System at Single Protein Resolution at JoVE.com

Membrane Transport Processes Analyzed by a Highly Parallel Nanopore Chip System at Single Protein Resolution

The presented protocol describes the analysis of membrane protein mediated transport on the single transporter level using pore-spanning solvent-free lipid bilayers. This is achieved by the creation of bulk produced nanopore array chips, combined with highly parallel data acquisition and analysis, enabling the future establishment of membrane protein effector screenings.

Membrane protein transport on the single protein level still evades detailed analysis, if the substrate translocated is non-electrogenic. Considerable ...

membrane-transport-processes-analyzed-highly-parallel-nanopore-chip

Research

JoVE Journal

Biology

11.7K Views.  Goethe University Frankfurt. The presented protocol describes the analysis of membrane protein mediated transport on the single transporter level using pore-spanning solvent-free lipid bilayers. This is achieved by the creation of bulk produced nanopore array chips, combined with highly parallel data acquisition and analysis, enabling the future establishment of membrane protein effector screenings.

Video: Membrane Transport Processes Analyzed by a Highly Parallel Nanopore Chip System at Single Protein Resolution

Fine-tuning the Size and Minimizing the Noise of Solid-state Nanopores

Solid-state nanopores have emerged as a versatile tool for the characterization of single biomolecules such as nucleic acids and proteins1. However, the creation of a nanopore in a thin insulating membrane remains challenging. Fabrication methods involving specialized focused electron beam systems can produce well-defined nanopores, but yield of reliable and low-noise nanopores in commercially available membranes remains low2,3 and size control is nontrivial4,5. Here, the application of high electric fields to fine-tune the size of the nanopore while ensuring optimal low-noise performance is demonstrated. These short pulses of high electric field are used to produce a pristine electrical signal and allow for enlarging of nanopores with subnanometer precision upon prolonged exposure. This method is performed in situ in an aqueous environment using standard laboratory equipment, improving the yield and reproducibility of solid-state nanopore fabrication.

A methodology for preparing solid-state nanopores in solution for biomolecular translocation experiments is presented. By applying short pulses of high electric fields, the nanopore diameter can be controllably enlarged with subnanometer precision and its electrical noise characteristics significantly improved. This procedure is performed in situ using standard laboratory equipment under experimental conditions.

Solid-state nanopores have emerged as a versatile tool for the characterization of single biomolecules such as nucleic acids and proteins1. However, the ...

Engineering

Monitoring Protein Adsorption with Solid-state Nanopores

Solid-state nanopores have been used to perform measurements at the single-molecule level to examine the local structure and flexibility of nucleic acids 1-6, the unfolding of proteins 7, and binding affinity of different ligands 8. By coupling these nanopores to the resistive-pulse technique 9-12, such measurements can be done under a wide variety of conditions and without the need for labeling 3. In the resistive-pulse technique, an ionic salt solution is introduced on both sides of the nanopore. Therefore, ions are driven from one side of the chamber to the other by an applied transmembrane potential, resulting in a steady current. The partitioning of an analyte into the nanopore causes a well-defined deflection in this current, which can be analyzed to extract single-molecule information. Using this technique, the adsorption of single proteins to the nanopore walls can be monitored under a wide range of conditions 13. Protein adsorption is growing in importance, because as microfluidic devices shrink in size, the interaction of these systems with single proteins becomes a concern. This protocol describes a rapid assay for protein binding to nitride films, which can readily be extended to other thin films amenable to nanopore drilling, or to functionalized nitride surfaces. A variety of proteins may be explored under a wide range of solutions and denaturing conditions. Additionally, this protocol may be used to explore more basic problems using nanopore spectroscopy.

A method of using solid-state nanopores to monitor the non-specific adsorption of proteins onto an inorganic surface is described. The method employs the resistive-pulse principle, allowing for the adsorption to be probed in real-time and at the single-molecule level. Because the process of single protein adsorption is far from equilibrium, we propose the employment of parallel arrays of synthetic nanopores, enabling for the quantitative determination of the apparent first-order reaction rate constant of protein adsorption as well as and the Langmuir adsorption constant.

Solid-state nanopores have been used to perform measurements at the single-molecule level to examine the local structure and flexibility of nucleic acids ...

Bioengineering

Single Liposome Measurements for the Study of Proton-Pumping Membrane Enzymes Using Electrochemistry and Fluorescent Microscopy

Proton-pumping enzymes of electron transfer chains couple redox reactions to proton translocation across the membrane, creating a proton-motive force used for ATP production. The amphiphilic nature of membrane proteins requires particular attention to their handling, and reconstitution into the natural lipid environment is indispensable when studying membrane transport processes like proton translocation. Here, we detail a method that has been used for the investigation of the proton-pumping mechanism of membrane redox enzymes, taking cytochrome bo3 from Escherichia coli as an example. A combination of electrochemistry and fluorescence microscopy is used to control the redox state of the quinone pool and monitor pH changes in the lumen. Due to the spatial resolution of fluorescent microscopy, hundreds of liposomes can be measured simultaneously while the enzyme content can be scaled down to a single enzyme or transporter per liposome. The respective single enzyme analysis can reveal patterns in the enzyme functional dynamics that might be otherwise hidden by the behavior of the whole population. We include a description of a script for automated image analysis.

Here, we present a protocol to study the molecular mechanism of proton translocation across lipid membranes of single liposomes, using cytochrome bo3 as an example. Combining electrochemistry and fluorescence microscopy, pH changes in the lumen of single vesicles, containing single or multiple enzyme, can be detected and analyzed individually.

Proton-pumping enzymes of electron transfer chains couple redox reactions to proton translocation across the membrane, creating a proton-motive force used ...

Biochemistry

High Resolution Physical Characterization of Single Metallic Nanoparticles

Individual molecules can be detected and characterized by measuring the degree by which they reduce the ionic current flowing through a single nanometer-scale pore. The signal is characteristic of the molecule&#39;s physicochemical properties and its interactions with the pore. We demonstrate that the nanopore formed by the bacterial protein exotoxin Staphylococcus aureus alpha hemolysin (&#945;HL) can detect polyoxometalates (POMs, anionic metal oxygen clusters), at the single molecule limit. Moreover, multiple degradation products of 12-phosphotungstic acid POM (PTA, H3PW12O40) in solution are simultaneously measured. The single molecule sensitivity of the nanopore method allows for POMs to be characterized at significantly lower concentrations than required for nuclear magnetic resonance (NMR) spectroscopy. This technique could serve as a new tool for chemists to study the molecular properties of polyoxometalates or other metallic clusters, to better understand POM synthetic processes, and possibly improve their yield. Hypothetically, the location of a given atom, or the rotation of a fragment in the molecule, and the metal oxidation state could be investigated with this method. In addition, this new technique has the advantage of allowing the real-time monitoring of molecules in solution.&#160;

Here, we present a protocol to detect discrete metal oxygen clusters, polyoxometalates (POMs), at the single molecule limit using a biological nanopore-based electronic platform. The method provides a complementary approach to traditional analytical chemistry tools used in the study of these molecules.

Individual molecules can be detected and characterized by measuring the degree by which they reduce the ionic current flowing through a single ...

Chemistry

Native Cell Membrane Nanoparticles System for Membrane Protein-Protein Interaction Analysis

Protein-protein interactions in cell membrane systems play crucial roles in a wide range of biological processes- from cell-to-cell interactions to signal transduction; from sensing environmental signals to biological response; from metabolic regulation to developmental control. Accurate structural information of protein-protein interactions is crucial for understanding the molecular mechanisms of membrane protein complexes and for the design of highly specific molecules to modulate these proteins. Many in vivo and in vitro approaches have been developed for the detection and analysis of protein-protein interactions. Among them the structural biology approach is unique in that it can provide direct structural information of protein-protein interactions at the atomic level. However, current membrane protein structural biology is still largely limited to detergent-based methods. The major drawback of detergent-based methods is that they often dissociate or denature membrane protein complexes once their native lipid bilayer environment is removed by detergent molecules. We have been developing a&#160;native cell membrane nanoparticle system for membrane protein structural biology. Here, we demonstrate the use of this system in the analysis of protein-protein interactions on the cell membrane with a case study of the oligomeric state of AcrB.

Presented here is a protocol for the determination of oligomeric state of membrane proteins that utilizes a native cell membrane nanoparticle system in conjunction with electron microscopy.

Protein-protein interactions in cell membrane systems play crucial roles in a wide range of biological processes- from cell-to-cell interactions to signal ...

Measuring Nucleotide Binding to Intact, Functional Membrane Proteins in Real Time

We have developed a method to measure binding of adenine nucleotides to intact, functional transmembrane receptors in a cellular or membrane environment. This method combines expression of proteins tagged with the fluorescent non-canonical amino acid ANAP, and FRET between ANAP and fluorescent (trinitrophenyl) nucleotide derivatives. We present examples of nucleotide binding to ANAP-tagged KATP ion channels measured in unroofed plasma membranes and excised, inside-out membrane patches under voltage clamp. The latter allows for simultaneous measurements of ligand binding and channel current, a direct readout of protein function. Data treatment and analysis are discussed extensively, along with potential pitfalls and artefacts. This method provides rich mechanistic insights into the ligand-dependent gating of KATP channels and can readily be adapted to the study of other nucleotide-regulated proteins or any receptor for which a suitable fluorescent ligand can be identified.

This protocol presents a method for measuring adenine nucleotide binding to receptors in real time in a cellular environment. Binding is measured as F&#246;rster resonance energy transfer (FRET) between trinitrophenyl nucleotide derivatives and protein labeled with a non-canonical, fluorescent amino acid.

We have developed a method to measure binding of adenine nucleotides to intact, functional transmembrane receptors in a cellular or membrane environment. ...

High-Resolution Studies of Proteins in Natural Membranes by Solid-State NMR

Membrane proteins are vital for cell function and thus represent important drug targets. Solid-state Nuclear Magnetic Resonance (ssNMR) spectroscopy offers a unique access to probe the structure and dynamics of such proteins in biological membranes of increasing complexity. Here, we present modern solid-state NMR spectroscopy as a tool to study structure and dynamics of proteins in natural lipid membranes and at atomic scale. Such spectroscopic studies profit from the use of high-sensitivity ssNMR methods, i.e., proton-(1H)-detected ssNMR and DNP (Dynamic Nuclear Polarization) supported ssNMR. Using bacterial outer membrane beta-barrel protein BamA and the ion channel KcsA, we present methods to prepare isotope-labeled membrane proteins and to derive structural and motional information by ssNMR.

This work details robust basic routines on how to prepare isotope-labeled membrane protein samples and analyze them at high-resolution with modern solid-state NMR spectroscopy methods.

Membrane proteins are vital for cell function and thus represent important drug targets. Solid-state Nuclear Magnetic Resonance (ssNMR) spectroscopy ...

Mass-Sensitive Particle Tracking to Characterize Membrane-Associated Macromolecule Dynamics

Short-lived or transient interactions of macromolecules at and with lipid membranes, an interface where a multitude of essential biological reactions take place, are inherently difficult to assess with standard biophysical methods. The introduction of mass-sensitive particle tracking (MSPT) constitutes an important step toward a thorough quantitative characterization of such processes. Technically, this was made possible through the advent of interferometric scattering microscopy (iSCAT)-based mass photometry (MP). When the background removal strategy is optimized to reveal the two-dimensional motion of membrane-associated particles, this technique allows the real-time analysis of both diffusion and molecular mass of unlabeled macromolecules on biological membranes. Here, a detailed protocol to perform and analyze mass-sensitive particle tracking of membrane-associated systems is described. Measurements performed on a commercial mass photometer achieve time resolution in the millisecond regime and, depending on the MP system, a mass detection limit down to 50 kDa. To showcase the potential of MSPT for the in-depth analysis of membrane-catalyzed macromolecule dynamics in general, results obtained for exemplary protein systems such as the native membrane interactor annexin V are presented.

This protocol describes an iSCAT-based image processing and single-particle tracking approach that enables the simultaneous investigation of the molecular mass and the diffusive behavior of macromolecules interacting with lipid membranes. Step-by-step instructions for sample preparation, mass-to-contrast conversion, movie acquisition, and post-processing are provided alongside directions to prevent potential pitfalls.

Short-lived or transient interactions of macromolecules at and with lipid membranes, an interface where a multitude of essential biological reactions take ...

Single-Molecule Imaging of Nuclear Transport

The utility of single molecule fluorescence microscopy approaches has been proven to be of a great avail in understanding biological reactions over the last decade. The investigation of molecular interactions with high temporal and spatial resolutions deep within cells has remained challenging due to the inherently weak signals arising from individual molecules. Recent works by Yang et al. demonstrated that narrow-field epifluorescence microscopy allows visualization of nucleocytoplasmic transport at the single molecule level. By the single molecule approach, important kinetics, such as nuclear transport time and efficiency, for signal-dependent and independent cargo molecules have been obtained. Here we described a protocol for the methodological approach with an improved spatiotemporal resolution of 0.4 ms and 12 nm. The improved resolution enabled us to capture transient active transport and passive diffusion events through the nuclear pore complexes (NPC) in semi-intact cells. We expect this method to be used in elucidating other binding and trafficking events within cells.

Single molecule microscopy approch provided novel insights into nuclear transport.

The utility of single molecule fluorescence microscopy approaches has been proven to be of a great avail in understanding biological reactions over the ...

Single-Molecule Imaging of Lateral Mobility and Ion Channel Activity in Lipid Bilayers using Total Internal Reflection Fluorescence (TIRF) Microscopy

High-resolution imaging techniques have shown that many ion channels are not static, but subject to highly dynamic processes, including the transient association of pore-forming and auxiliary subunits, lateral diffusion, and clustering with other proteins. However, the relationship between lateral diffusion and function is poorly understood. To approach this problem, we describe how lateral mobility and activity of individual channels in supported lipid membranes can be monitored and correlated using total internal reflection fluorescence (TIRF) microscopy. Membranes are fabricated on an ultrathin hydrogel substrate using the droplet interface bilayer (DIB) technique. Compared to other types of model membranes, these membranes have the advantage of being mechanically robust and suitable for highly sensitive analytical techniques. This protocol measures Ca2+ ion flux through single channels by observing the fluorescence emission of a Ca2+-sensitive dye in close proximity to the membrane. In contrast to classical single-molecule tracking approaches, no fluorescent fusion proteins or labels, which can interfere with lateral movement and function in the membrane, are required. Possible changes in ion flux associated with conformational changes of the protein are only due to protein lateral motion in the membrane. Representative results are shown using the mitochondrial protein translocation channel TOM-CC and the bacterial channel OmpF. In contrast to OmpF, the gating of TOM-CC is very sensitive to molecular confinement and the nature of lateral diffusion. Hence, supported droplet-interface bilayers are a powerful tool to characterize the link between lateral diffusion and the function of ion channels.

Single-Molecule Imaging of Lateral Mobility and Ion Channel Activity in Lipid Bilayers using Total Internal Reflection Fluorescence TIRF Microscopy

This protocol describes how to use TIRF microscopy to track individual ion channels and determine their activity in supported lipid membranes, thereby defining the interplay between lateral membrane movement and channel function. It describes how to prepare the membranes, record the data, and analyze the results.

High-resolution imaging techniques have shown that many ion channels are not static, but subject to highly dynamic processes, including the transient ...