The financial support by DFG (German research foundation, project CZ 55/30-1) for parts of this work is gratefully acknowledged.

1. Assembling the Experimental Setup
<ol>
	<li>Preparing the proximal side
	<ol>
		<li>Place and fix the laser providing a collimated light beam &#8211; or use a fiber-coupled laser with collimation optics at the exit facet of the fiber.</li>
		<li>Put the polarizing beam splitter (PBS) to split the laser beam into reference and object beam. Turn the orientation of the half wave plates (HWP) by rotating the HWP in its rotation mount until the power of reference beam and object beam (at the distal side) is roughly the same. Check this by putting a screen into both reference and object beam. Choose the orientation of the PBS so that the polarization of the reference beam fits the polarization-sensitive spatial light modulator (SLM).</li>
		<li>Put a beam splitter (BS) into the reference beam to split the reference beam into two beams. Place the optical modulators (OM) such that these two beams coming from BS1 can pass OM1 and OM2, respectively.</li>
		<li>Combine the two beams passing OM1 and OM2 at BS2 employing two mirrors. Adjust the beam splitters and mirrors so that both beams are spatially separated.</li>
		<li>Carefully align BS5 to ensure that the direction of incidence of both beams is perpendicular to the pixel plane of the SLM, ignoring BS3 and BS4 at first. At first, nothing is displayed on the SLM, i.e., it acts like a mirror until the end of the calibration (throughout step 2).</li>
		<li>Adjust the position and the distance between the two lenses (L) constituting a Keplerian telescope in order to get a sharp image of the SLM plane on the complementary metal-oxide semiconductor (CMOS) camera. Watch the correct orientation of L1 and L2 (flat sides are facing each other) to minimize aberrations.</li>
	</ol>
	</li>
	<li>Preparing the distal side
	<ol>
		<li>Use BS7 to split the object beam into two beams and combine them at BS8 employing two mirrors. Again, adjust the beam splitters and mirrors so that both beams are spatially separated.</li>
		<li>Deflect both beams using BS9 to aim them to the microscope objective (OBJ). Focus OBJ2 on the distal end of the multimode fiber (MMF). Check the focus by observing the back reflection from the MMF employing L3 and a charge-coupled device (CCD) camera.</li>
	</ol>
	</li>
	<li>Connecting proximal and distal side
	<ol>
		<li>Collimate the light from the object beam exiting the MMF employing OBJ1.</li>
		<li>Split the object beam using BS6, ignore the linear polarizer (LP) at first. Combine both object beams with both reference beams at BS3 and BS4 employing a mirror. Adjust the beam splitters and mirrors so that each pair of reference and object beam overlap at the SLM, intersecting with a small angle (less than 1&#176;).</li>
		<li>Ensure that the power of the reference and the object beam are approximately equal by turning the orientation of the HWP, according to step 1.1.2.</li>
		<li>Check the interference pattern (off-axis hologram) at the CMOS camera and adjust the intersection angle accordingly. Increase the angle, until the interference fringe spacing roughly equals the size of two pixels on the CMOS camera.</li>
		<li>Adjust the orientation of the LP to match the polarization of object and reference beam in order to get a maximum contrast of the interference pattern in the CMOS camera image, so that the camera image shows distinct fringes.</li>
	</ol>
	</li>
</ol>
2. Calibrating the System
<ol>
	<li>Calibrating the pixel relation between SLM and CMOS
	<ol>
		<li>Illuminate the whole SLM using only one of the reference beams and block the other reference and objects beams.</li>
		<li>Capture an image of the SLM with the CMOS camera.</li>
		<li>Get the coordinates of the upper left corner of the SLM in the CMOS camera image, e.g. using graphics software and the mouse cursor at the PC. Use these pixel coordinates as the point of origin regarding the SLM.</li>
		<li>Remove all beam blocks.</li>
	</ol>
	</li>
	<li>Calibrating the signal paths
	<ol>
		<li>Block both reference beam 2 and object beam 2.</li>
		<li>Capture an image of the hologram with the CMOS camera. Evaluate the phase in the recorded hologram using angular spectrum method19. Calculate the inverted phase in the corresponding region of beam 1.</li>
		<li>Remove the former beam blocks and now block both reference beam 1 and object beam 1.</li>
		<li>Capture an image of the hologram with the CMOS camera. Measure the phase in the recorded hologram using angular spectrum method again. Calculate the inverted phase at the corresponding region of beam 2.</li>
		<li>Remove all beam blocks.</li>
	</ol>
	</li>
</ol>
3. Transmitting the Signals
<ol>
	<li>Block the object beam.</li>
	<li>Stitch the calculated inverted phase images at the corresponding regions of beam 1 and 2 together and display the entire image on the SLM, typically using the computer graphics port.</li>
	<li>Start the modulation of the input signals 1 and 2 by activating OM1 and OM2.</li>
	<li>Observe the output signals 1 and 2 on the CCD camera.</li>
</ol>

<ol>
	<li>Richardson, D. J., Fini, J. M., Nelson, L. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Space-division+multiplexing+in+optical+fibres.">Space-division multiplexing in optical fibres.</a> Nat. Photonics. 7 (5), 354-362 (2013).</li><li>Kreysing, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dynamic+operation+of+optical+fibres+beyond+the+single-mode+regime+facilitates+the+orientation+of+biological+cells.">Dynamic operation of optical fibres beyond the single-mode regime facilitates the orientation of biological cells.</a> Nat. Commun. 5 (5481), 1-6 (2014).</li><li>Winzer, P. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Scaling+optical+fiber+networks:+Challenges+and+solutions.">Scaling optical fiber networks: Challenges and solutions.</a> Opt. Photonics News. 26 (3), 28-35 (2015).</li><li>Ci&#382;m&#225;r, T., Dholakia, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Shaping+the+light+transmission+through+a+multimode+optical+fibre:+complex+transformation+analysis+and+applications+in+biophotonics.">Shaping the light transmission through a multimode optical fibre: complex transformation analysis and applications in biophotonics.</a> Opt. Express. 19 (20), 18871-18884 (2011).</li><li>Boyden, E. S., Zhang, F., Bamberg, E., Nagel, G., Deisseroth, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Millisecond-timescale,+genetically+targeted+optical+control+of+neural+activity.">Millisecond-timescale, genetically targeted optical control of neural activity.</a> Nat. Neurosci. 8 (9), 1263-1268 (2005).</li><li>Philipp, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Volumetric+HiLo+microscopy+employing+an+electrically+tunable+lens.">Volumetric HiLo microscopy employing an electrically tunable lens.</a> Opt. Express. 24 (13), 15029-15041 (2016).</li><li>B&#252;ttner, L., Leithold, C., Czarske, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Interferometric+velocity+measurements+through+a+fluctuating+gas-liquid+interface+employing+adaptive+optics.">Interferometric velocity measurements through a fluctuating gas-liquid interface employing adaptive optics.</a> Opt. Express. 21 (25), 30653-30663 (2013).</li><li>Vellekoop, I. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Feedback-based+wavefront+shaping.">Feedback-based wavefront shaping.</a> Opt. Express. 23 (9), 12189-12206 (2015).</li><li>Mahalati, R. N., Askarov, D., Wilde, J. P., Kahn, J. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adaptive+control+of+input+field+to+achieve+desired+output+intensity+profile+in+multimode+fiber+with+random+mode+coupling.">Adaptive control of input field to achieve desired output intensity profile in multimode fiber with random mode coupling.</a> Opt. Express. 20 (13), 14321-14337 (2012).</li><li>Caravaca-Aguirre, A. M., Niv, E., Conkey, D. B., Piestun, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Real-time+resilient+focusing+through+a+bending+multimode+fiber.">Real-time resilient focusing through a bending multimode fiber.</a> Opt. Express. 21 (10), 12881-12887 (2013).</li><li>Ci&#382;m&#225;r, T., Dholakia, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Exploiting+multimode+waveguides+for+pure+fibre-based+imaging.">Exploiting multimode waveguides for pure fibre-based imaging.</a> Nat. Commun. 3, 1027 (2012).</li><li>Yaqoob, Z., Psaltis, D., Feld, M. S., Yang, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optical+phase+conjugation+for+turbidity+suppression+in+biological+samples.">Optical phase conjugation for turbidity suppression in biological samples.</a> Nat. Photonics. 2 (2), 110-115 (2008).</li><li>Ma, C., Xu, X., Liu, Y., Wang, L. V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Time-reversed+adapted-perturbation+(TRAP)+optical+focusing+onto+dynamic+objects+inside+scattering+media.">Time-reversed adapted-perturbation (TRAP) optical focusing onto dynamic objects inside scattering media.</a> Nat. Photonics. 8 (12), 931-936 (2014).</li><li>Lee, K., Lee, J., Park, J. H., Park, J. H., Park, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=One-wave+optical+phase+conjugation+mirror+by+actively+coupling+arbitrary+light+fields+into+a+single-mode+reflector.">One-wave optical phase conjugation mirror by actively coupling arbitrary light fields into a single-mode reflector.</a> Phys. Rev. Lett. 115 (15), 153902 (2015).</li><li>Cui, M., Yang, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Implementation+of+a+digital+optical+phase+conjugation+system+and+its+application+to+study+the+robustness+of+turbidity+suppression+by+phase+conjugation.">Implementation of a digital optical phase conjugation system and its application to study the robustness of turbidity suppression by phase conjugation.</a> Opt. Express. 18 (4), 3444-3455 (2010).</li><li>Hillman, T. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Digital+optical+phase+conjugation+for+delivering+two-dimensional+images+through+turbid+media.">Digital optical phase conjugation for delivering two-dimensional images through turbid media.</a> Sci. Rep. 3, (2013).</li><li>Papadopoulos, I. N., Farahi, S., Moser, C., Psaltis, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Focusing+and+scanning+light+through+a+multimode+optical+fiber+using+digital+phase+conjugation.">Focusing and scanning light through a multimode optical fiber using digital phase conjugation.</a> Opt. Express. 20 (10), 10583-10590 (2012).</li><li>Czarske, J. W., Haufe, D., Koukourakis, N., B&#252;ttner, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transmission+of+independent+signals+through+a+multimode+fiber+using+digital+optical+phase+conjugation.">Transmission of independent signals through a multimode fiber using digital optical phase conjugation.</a> Opt. Express. 24 (13), 15128-15136 (2016).</li><li>Kim, M. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Principles+and+techniques+of+digital+holographic+microscopy.">Principles and techniques of digital holographic microscopy.</a> SPIE Rev. 1 (1), 01800501-01800550 (2010).</li><li>Gu, R. Y., Mahalati, R. N., Kahn, J. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+of+flexible+multi-mode+fiber+endoscope.">Design of flexible multi-mode fiber endoscope.</a> Opt. Express. 23 (21), 26905-26918 (2015).</li><li>Katz, O., Small, E., Bromberg, Y., Silberberg, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Focusing+and+compression+of+ultrashort+pulses+through+scattering+media.">Focusing and compression of ultrashort pulses through scattering media.</a> Nat. Photonics. 5 (6), 372-377 (2011).</li></ol>

The authors have nothing to disclose.

The assembling of the experimental setup (step 1 in the protocol) requires a thorough alignment of the optical components with respect to each other. The most important aspect is the rectangular incidence of the reference beams onto the SLM in order to ensure a high PBR.
In order to enhance the setup to more than two transmitted signals, additional beam splitters could be used. As an alternative, a fiber-based implementation would be more compact and robust allowing the system to be portable f...

The transmission of multiple light signals through a multimode fiber (MMF) is evident in communications engineering1 and biophotonics2. In communications engineering, space-division multiplexing (SDM) is believed to be a viable solution in order to enhance the transmission capacity of optical fibers for future data transfer applications benefiting from a higher utilization of the limited space, compared to multiple single-mode fibers3. In biophotonics, biological samples are manipulated by light transmitting through an MMF endoscope4. For example, the independent optical control of individual neurons using MMF endoscopes is of interest for optogenetics in order to study neuronal networks in the brain5. However, the light projected onto the MMF input facet is subject to distortion due to mode mixing and dispersion during propagation to the output facet of the MMF. As a result, the light propagation is altered, which makes signal transmission challenging.
Wavefront shaping methods6,7 are applied in scattering media using spatial light modulators (SLM) and enable the compensation for the distortion due to scattering during light propagation8. There are iterative approaches that optimize the output using an optical feedback9. These approaches are rather time consuming because of the necessity for numerous iterations and the high degree of freedom, corresponding to a large number of modulator elements. Another approach is to completely determine the distortion within the MMF described by its transmission matrix10. If the number of modes to be transmitted is large, this will be time consuming as well. In contrast, digital optical phase conjugation (DOPC) is considered to be fast and advantageous here, since only few focal spots have to be generated at the output facet of the MMF. Phase conjugation approaches have also been demonstrated for focusing or imaging through biological tissue12,13,14.
So far, DOPC was employed for a single time signal only15,16, and was applied for the transmission of light through an MMF17. A DOPC approach for multiple independent signals has not been accomplished. We have developed an enhanced DOPC method providing the independent transmission of multiple light signals using individual wavefront shaping for each signal employing a single phase-only SLM18. To this aim, the SLM is segmented into regions, one for each signal to be transmitted. The proposed experimental setup is depicted in Figure 1, where a calibration is performed in a) before the actual transmission happens in b).
<img alt="Figure 1" src="/files/ftp_upload/55407/55407fig1.jpg" /> 
Figure 1: Experimental setup. BS = beam splitter, CCD = charge-coupled device, OM = optical modulator, CMOS = complementary metal-oxide semiconductor, HWP = half wave plate, L = lens, LP = linear polarizer, MMF = multimode fiber, OBJ = microscope objective, PBS = polarizing beam splitter, SLM = spatial light modulator (phase only) &#8212; only relevant beams for&#160;(a) the calibration and&#160;(b) the transmission are depicted <a href="http://cloudflare.jove.com/files/ftp_upload/55407/55407fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>spatial light modulator</td>
			<td>Holoeye</td>
			<td>PLUTO&#8208;VIS&#8208;016</td>
			<td></td>
		</tr>
		<tr>
			<td>CMOS camera</td>
			<td>Mikrotron</td>
			<td>MC4082</td>
			<td></td>
		</tr>
		<tr>
			<td>diode&#8208;pumped solid state laser</td>
			<td>Laser Quantum</td>
			<td>torus 532</td>
			<td></td>
		</tr>
		<tr>
			<td>CCD camera</td>
			<td>IDS</td>
			<td>U3&#8208;3482LE&#8208;M</td>
			<td>CMOS camera; suitable as well</td>
		</tr>
		<tr>
			<td>lens 1</td>
			<td>Qioptiq</td>
			<td>G063204000</td>
			<td></td>
		</tr>
		<tr>
			<td>lens 2</td>
			<td>Qioptiq</td>
			<td>G063203000</td>
			<td></td>
		</tr>
		<tr>
			<td>lens 3</td>
			<td>Thorlabs</td>
			<td>AC508&#8208;180&#8208;A&#8208;ML</td>
			<td></td>
		</tr>
		<tr>
			<td>multimode fiber</td>
			<td>Thorlabs</td>
			<td>M14L02</td>
			<td></td>
		</tr>
		<tr>
			<td>beam splitters</td>
			<td>Thorlabs</td>
			<td>BS013</td>
			<td>9x</td>
		</tr>
		<tr>
			<td>polarizing beam splitters</td>
			<td>Thorlabs</td>
			<td>PBS251</td>
			<td></td>
		</tr>
		<tr>
			<td>mirrors</td>
			<td>Thorlabs</td>
			<td>PF10&#8208;03&#8208;P01</td>
			<td>5x</td>
		</tr>
		<tr>
			<td>microscope objectives</td>
			<td>Thorlabs</td>
			<td>RMS20X</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>half wave plates</td>
			<td>Thorlabs</td>
			<td>WPH10M&#8208;532</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>linear polarizer</td>
			<td>Thorlabs</td>
			<td>LPVISB050&#8208;MP2</td>
			<td></td>
		</tr>
		<tr>
			<td>optical modulators</td>
			<td>Thorlabs</td>
			<td>MC2000B&#8208;EC</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>linear and rotation stage for CMOS camera</td>
			<td>Thorlabs</td>
			<td>XYR1/M</td>
			<td></td>
		</tr>
		<tr>
			<td>fiber connector</td>
			<td>Thorlabs</td>
			<td>S120&#8208;SMA</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>reducing ring for microscope objectives</td>
			<td>Qioptiq</td>
			<td>G061621000</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>xy adjustment for objective adapters</td>
			<td>Qioptiq</td>
			<td>G061025000</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>z translation mount for fiber adapter</td>
			<td>Thorlabs</td>
			<td>SM1Z</td>
			<td>2x</td>
		</tr>
		<tr>
			<td>rods for fiber alignment to objectives</td>
			<td>Qioptiq</td>
			<td>G061210000</td>
			<td>8x</td>
		</tr>
		<tr>
			<td>mounts for lenses 1 and 2 plus two phantom mounts</td>
			<td>Qioptiq</td>
			<td>G061047000</td>
			<td>4x</td>
		</tr>
		<tr>
			<td>rail carriers for objective and lens mounts</td>
			<td>Qioptiq</td>
			<td>G061372000</td>
			<td>6x</td>
		</tr>
		<tr>
			<td>rail for rail carriers</td>
			<td>Qioptiq</td>
			<td>G061359000</td>
			<td>2x</td>
		</tr>
		<tr>
			<td colspan="2">adapter for CCD camera to 1 post</td>
			<td></td>
			<td>in-house</td>
		</tr>
		<tr>
			<td>adapter for laser to 4 posts</td>
			<td></td>
			<td></td>
			<td>in-house</td>
		</tr>
		<tr>
			<td>mount for lens 3</td>
			<td>Thorlabs</td>
			<td>LMR2/M</td>
			<td></td>
		</tr>
		<tr>
			<td>mounts for half wave plates</td>
			<td>Thorlabs</td>
			<td>RSP1D/M</td>
			<td>2</td>
		</tr>
		<tr>
			<td>mounts for mirrors</td>
			<td>Thorlabs</td>
			<td>KM100</td>
			<td>5x</td>
		</tr>
		<tr>
			<td>mount for linear polarizer</td>
			<td>Thorlabs</td>
			<td>RSP05/M</td>
			<td></td>
		</tr>
		<tr>
			<td>mounts for beam splitters and SLM</td>
			<td>Thorlabs</td>
			<td>KM100PM/M</td>
			<td>11x</td>
		</tr>
		<tr>
			<td>clamping arms for beam splitters and SLM</td>
			<td>Thorlabs</td>
			<td>PM4/M</td>
			<td>11x</td>
		</tr>
		<tr>
			<td>posts for mounts, rail carriers and adapters</td>
			<td>Thorlabs</td>
			<td>TR75/M</td>
			<td>29x</td>
		</tr>
		<tr>
			<td>holders for posts</td>
			<td>Thorlabs</td>
			<td>PH50/M</td>
			<td>29x</td>
		</tr>
		<tr>
			<td>pedestals for holders</td>
			<td>Thorlabs</td>
			<td>BE1/M</td>
			<td>29x</td>
		</tr>
		<tr>
			<td>clamping forks for pedestals</td>
			<td>Thorlabs</td>
			<td>CF125</td>
			<td>29x</td>
		</tr>
	</tbody>
</table>

transmission of multiple signals through an optical fiber using wavefront shaping

The transmission of multiple independent optical signals through a multimode fiber is accomplished using wavefront shaping in order to compensate for the light distortion during the propagation within the fiber. Our methodology is based on digital optical phase conjugation employing only a single spatial light modulator, where the optical wavefront is individually modulated at different regions of the modulator, one region per light signal. Digital optical phase conjugation approaches are considered to be faster than other wavefront shaping approaches, where (for example) a complete determination of the wave propagation behavior of the fiber is performed. In contrast, the presented approach is time-efficient since it only requires one calibration per light signal. The proposed method is potentially appropriate for spatial division multiplexing in communications engineering. Further application fields are endoscopic light delivery in biophotonics, especially in optogenetics, where single cells in biological tissue have to be selectively illuminated with high spatial and temporal resolution.

Typical output signals at the distal side of the 2 m long fiber are depicted in Figure 2. Note that the desired focal spot (peak) is accompanied by an undesired speckle pattern (background), which is due to imperfection of the DOPC as a matter of principle. The corresponding peak-to-background ratio (PBR) amounts to 53 (solely signal 1 is &#39;on&#39;), 36 (solely signal 2 is &#39;on&#39;) and 20 (both signals 1 and 2 are &#39;on&#39;) here, respectively. The PBR can be i...

Watch this Scientific Journal Video about Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping at JoVE.com

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

We demonstrate the transmission of multiple independent signals through a multimode fiber using wavefront shaping employing a single spatial light modulator. By modulating the wavefront for each signal individually, spatially separated foci are transmitted. Potential applications are multiplexed data transfer in communications engineering and endoscopic light delivery in biophotonics.

The transmission of multiple independent optical signals through a multimode fiber is accomplished using wavefront shaping in order to compensate for the ...

transmission-multiple-signals-through-an-optical-fiber-using

Research

Education

JoVE Core

JoVE Journal

Electrical Engineering

Bioengineering

Unit 1

Diagrams and Signal Flow Graphs

SCIENTISTS IN ACTION

9.7K Views.  TU Dresden. We demonstrate the transmission of multiple independent signals through a multimode fiber using wavefront shaping employing a single spatial light modulator. By modulating the wavefront for each signal individually, spatially separated foci are transmitted. Potential applications are multiplexed data transfer in communications engineering and endoscopic light delivery in biophotonics.

Video: Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Three-dimensional Optical-resolution Photoacoustic Microscopy

Optical microscopy, providing valuable insights at the cellular and organelle levels, has been widely recognized as an enabling biomedical technology. As the mainstays of in vivo three-dimensional (3-D) optical microscopy, single-/multi-photon fluorescence microscopy and optical coherence tomography (OCT) have demonstrated their extraordinary sensitivities to fluorescence and optical scattering contrasts, respectively. However, the optical absorption contrast of biological tissues, which encodes essential physiological/pathological information, has not yet been assessable. 
The emergence of biomedical photoacoustics has led to a new branch of optical microscopy optical-resolution photoacoustic microscopy (OR-PAM)1, where the optical irradiation is focused to the diffraction limit to achieve cellular1 or even subcellular2 level lateral resolution. As a valuable complement to existing optical microscopy technologies, OR-PAM brings in at least two novelties. First and most importantly, OR-PAM detects optical absorption contrasts with extraordinary sensitivity (i.e., 100%). Combining OR-PAM with fluorescence microscopy3 or with optical-scattering-based OCT4 (or with both) provides comprehensive optical properties of biological tissues. Second, OR-PAM encodes optical absorption into acoustic waves, in contrast to the pure optical processes in fluorescence microscopy and OCT, and provides background-free detection. The acoustic detection in OR-PAM mitigates the impacts of optical scattering on signal degradation and naturally eliminates possible interferences (i.e., crosstalks) between excitation and detection, which is a common problem in fluorescence microscopy due to the overlap between the excitation and fluorescence spectra. 
Unique for optical absorption imaging, OR-PAM has demonstrated broad biomedical applications since its invention, including, but not limited to, neurology5, 6, ophthalmology7, 8, vascular biology9, and dermatology10. In this video, we teach the system configuration and alignment of OR-PAM as well as the experimental procedures for in vivo functional microvascular imaging.

Optical-resolution photoacoustic microscopy (OR-PAM) is an emerging technology capable of imaging optical absorption contrasts in vivo with cellular resolution and sensitivity. Here, we provide a visualized instruction on the experimental protocols of OR-PAM, including system configuration, system alignment, typical in vivo experimental procedures, and functional imaging schemes.

Optical microscopy, providing valuable insights at the cellular and organelle levels, has been widely recognized as an enabling biomedical technology. As ...

Attaching Biological Probes to Silica Optical Biosensors Using Silane Coupling Agents

In order to interface with biological environments, biosensor platforms, such as the popular Biacore system (based on the Surface Plasmon Resonance (SPR) technique), make use of various surface modification techniques, that can, for example, prevent surface fouling, tune the hydrophobicity / hydrophilicity of the surface, adapt to a variety of electronic environments, and most frequently, induce specificity towards a target of interest.1-5 These techniques extend the functionality of otherwise highly sensitive biosensors to real-world applications in complex environments, such as blood, urine, and wastewater analysis.2,6-7 While commercial biosensing platforms, such as Biacore, have well-understood, standard techniques for performing such surface modifications, these techniques have not been translated in a standardized fashion to other label-free biosensing platforms, such as Whispering Gallery Mode (WGM) optical resonators.8-9
WGM optical resonators represent a promising technology for performing label-free detection of a wide variety of species at ultra-low concentrations.6,10-12 The high sensitivity of these platforms is a result of their unique geometric optics: WGM optical resonators confine circulating light at specific, integral resonance frequencies.13 Like the SPR platforms, the optical field is not totally confined to the sensor device, but evanesces; this "evanescent tail" can then interact with species in the surrounding environment. This interaction causes the effective refractive index of the optical field to change, resulting in a slight, but detectable, shift in the resonance frequency of the device. Because the optical field circulates, it can interact many times with the environment, resulting in an inherent amplification of the signal, and very high sensitivities to minor changes in the environment.2,14-15
To perform targeted detection in complex environments, these platforms must be paired with a probe molecule (usually one half of a binding pair, e.g. antibodies / antigens) through surface modification.2 Although WGM optical resonators can be fabricated in several geometries from a variety of material systems, the silica microsphere is the most common. These microspheres are generally fabricated on the end of an optical fiber, which provides a "stem" by which the microspheres can be handled during functionalization and detection experiments. Silica surface chemistries may be applied to attach probe molecules to their surfaces; however, traditional techniques generated for planar substrates are often not adequate for these three-dimensional structures, as any changes to the surface of the microspheres (dust, contamination, surface defects, and uneven coatings) can have severe, negative consequences on their detection capabilities. Here, we demonstrate a facile approach for the surface functionalization of silica microsphere WGM optical resonators using silane coupling agents to bridge the inorganic surface and the biological environment, by attaching biotin to the silica surface.8,16 Although we use silica microsphere WGM resonators as the sensor system in this report, the protocols are general and can be used to functionalize the surface of any silica device with biotin.

Biosensors interface with complex, biological environments and perform targeted detection by combining highly sensitive sensors with highly specific probes attached to the sensor via surface modification. Here, we demonstrate the surface functionalization of silica optical sensors with biotin using silane coupling agents to bridge the sensor and the biological environment.

In order to interface with biological environments, biosensor platforms, such as the popular Biacore system (based on the Surface Plasmon Resonance (SPR) ...

Induction of Adhesion-dependent Signals Using Low-intensity Ultrasound

In multicellular organisms, cell behavior is dictated by interactions with the extracellular matrix. Consequences of matrix-engagement range from regulation of cell migration and proliferation, to secretion and even differentiation. The signals underlying each of these complex processes arise from the molecular interactions of extracellular matrix receptors on the surface of the cell. Integrins are the prototypic receptors and provide a mechanical link between extracellular matrix and the cytoskeleton, as well as initiating some of the adhesion-dependent signaling cascades. However, it is becoming increasingly apparent that additional transmembrane receptors function alongside the integrins to regulate both the integrin itself and signals downstream. The most elegant of these examples is the transmembrane proteoglycan, syndecan-4, which cooperates with &alpha;5&beta;1-integrin during adhesion to fibronectin. In vivo models demonstrate the importance of syndecan-4 signaling, as syndecan-4-knockout mice exhibit healing retardation due to inefficient fibroblast migration1,2. In wild-type animals, migration of fibroblasts toward a wound is triggered by the appearance of fibronectin that leaks from damaged capillaries and is deposited by macrophages in injured tissue. Therefore there is great interest in discovering strategies that enhance fibronectin-dependent signaling and could accelerate repair processes.
The integrin-mediated and syndecan-4-mediated components of fibronectin-dependent signaling can be separated by stimulating cells with recombinant fibronectin fragments. Although integrin engagement is essential for cell adhesion, certain fibronectin-dependent signals are regulated by syndecan-4. Syndecan-4 activates the Rac1 protrusive signal3, causes integrin redistribution1, triggers recruitment of cytoskeletal molecules, such as vinculin, to focal adhesions4, and thereby induces directional migration3. We have looked for alternative strategies for activating such signals and found that low-intensity pulsed ultrasound (LIPUS) can mimic the effects of syndecan-4 engagement5. In this protocol we describe the method by which 30 mW/cm2, 1.5 MHz ultrasound, pulsed at 1 kHz (Fig. 1) can be applied to fibroblasts in culture (Fig. 2) to induce Rac1 activation and focal adhesion formation. Ultrasound stimulation is applied for a maximum of 20 minutes, as this combination of parameters has been found to be most efficacious for acceleration of clinical fracture repair6. The method uses recombinant fibronectin fragments to engage &alpha;5&beta;1-integrin, without engagement of syndecan-4, and requires inhibition of protein synthesis by cycloheximide to block deposition of additional matrix by the fibroblasts., The positive effect of ultrasound on repair mechanisms is well documented7,8, and by understanding the molecular effect of ultrasound in culture we should be able to refine the therapeutic technique to improve clinical outcomes.

This protocol describes the stimulation of cultured fibroblasts with low-intensity pulsed ultrasound, which drives focal adhesion formation and Rac1 activation by mimicking engagement of the transmembrane matrix receptor, syndecan-4. This approach allows investigation of a successful clinical technique at the cellular level, thereby providing opportunities for refinement of the therapy.

In multicellular organisms, cell behavior is dictated by interactions with the extracellular matrix. Consequences of matrix-engagement range from ...

In vitro Synthesis of Native, Fibrous Long Spacing and Segmental Long Spacing Collagen

Collagen fibrils are present in the extracellular matrix of animal tissue to provide structural scaffolding and mechanical strength. These native collagen fibrils have a characteristic banding periodicity of ~67 nm and are formed in vivo through the hierarchical assembly of Type I collagen monomers, which are 300 nm in length and 1.4 nm in diameter. In vitro, by varying the conditions to which the monomer building blocks are exposed, unique structures ranging in length scales up to 50 microns can be constructed, including not only native type fibrils, but also fibrous long spacing and segmental long spacing collagen. Herein, we present procedures for forming the three different collagen structures from a common commercially available collagen monomer. Using the protocols that we and others have published in the past to make these three types typically lead to mixtures of structures. In particular, unbanded fibrils were commonly found when making native collagen, and native fibrils were often present when making fibrous long spacing collagen. These new procedures have the advantage of producing the desired collagen fibril type almost exclusively. The formation of the desired structures is verified by imaging using an atomic force microscope.

In vitro Synthesis of Native, Fibrous Long Spacing and Segmental Long Spacing Collagen

Simple and reproducible procedures are described for making three structurally distinct collagen assemblies from a common commercially available Type I collagen monomer. Native type, fibrous long spacing or segmental long spacing collagen can be constructed by varying the conditions to which the 300 nm long and 1.4 nm diameter monomer building block is exposed.

Collagen fibrils are present in the  extracellular matrix of animal tissue to provide structural scaffolding and  mechanical strength. These native ...

Label-free Single Molecule Detection Using Microtoroid Optical Resonators

Detecting small concentrations of molecules down to the single molecule limit has impact on areas such as early detection of disease, and fundamental studies on the behavior of molecules. Single molecule detection techniques commonly utilize labels such as fluorescent tags or quantum dots, however, labels are not always available, increase cost and complexity, and can perturb the events being studied. Optical resonators have emerged as a promising means to detect single molecules without the use of labels. Currently the smallest particle detected by a non-plasmonically-enhanced bare optical resonator system in solution is a 25 nm polystyrene sphere1. We have developed a technique known as Frequency Locking Optical Whispering Evanescent Resonator (FLOWER) that can surpass this limit and achieve label-free single molecule detection in aqueous solution2. As signal strength scales with particle volume, our work represents a &#62; 100x improvement in the signal to noise ratio (SNR) over the current state of the art. Here the procedures behind FLOWER are presented in an effort to increase its usage in the field.

We have developed a label-free biosensing system based on optical resonator technology known as Frequency Locking Optical Whispering Evanescent Resonator (FLOWER) that is capable of detecting single molecules in solution. Here the procedures behind this work are described and presented.

Detecting small concentrations of molecules down to the single molecule limit has impact on areas such as early detection of disease, and fundamental ...

Multicolor Fluorescence Detection for Droplet Microfluidics Using Optical Fibers

Fluorescence assays are the most common readouts used in droplet microfluidics due to their bright signals and fast time response. Applications such as multiplex assays, enzyme evolution, and molecular biology enhanced cell sorting require the detection of two or more colors of fluorescence. Standard multicolor detection systems that couple free space lasers to epifluorescence microscopes are bulky, expensive, and difficult to maintain. In this paper, we describe a scheme to perform multicolor detection by exciting discrete regions of a microfluidic channel with lasers coupled to optical fibers. Emitted light is collected by an optical fiber coupled to a single photodetector. Because the excitation occurs at different spatial locations, the identity of emitted light can be encoded as a temporal shift, eliminating the need for more complicated light filtering schemes. The system has been used to detect droplet populations containing four unique combinations of dyes and to detect sub-nanomolar concentrations of fluorescein.

Multicolor fluorescence detection in droplet microfluidics typically involves bulky and complex epifluorescence microscope-based detection systems. Here we describe a compact and modular multicolor detection scheme that utilizes an array of optical fibers to temporally encode multicolor data collected by a single photodetector.

Fluorescence assays are the most common readouts used in droplet microfluidics due to their bright signals and fast time response. Applications such as ...

Determination of Zeta Potential via Nanoparticle Translocation Velocities through a Tunable Nanopore: Using DNA-modified Particles as an Example

Nanopore technologies, known collectively as Resistive Pulse Sensors (RPS), are being used to detect, quantify and characterize proteins, molecules and nanoparticles. Tunable resistive pulse sensing (TRPS) is a relatively recent adaptation to RPS that incorporates a tunable pore that can be altered in real time. Here, we use TRPS to monitor the translocation times of DNA-modified nanoparticles as they traverse the tunable pore membrane as a function of DNA concentration and structure (i.e., single-stranded to double-stranded DNA).
TRPS is based on two Ag/AgCl electrodes, separated by an elastomeric pore membrane that establishes a stable ionic current upon an applied electric field. Unlike various optical-based particle characterization technologies, TRPS can characterize individual particles amongst a sample population, allowing for multimodal samples to be analyzed with ease. Here, we demonstrate zeta potential measurements via particle translocation velocities of known standards and apply these to sample analyte translocation times, thus resulting in measuring the zeta potential of those analytes.
As well as acquiring mean zeta potential values, the samples are all measured using a particle-by-particle perspective exhibiting more information on a given sample through sample population distributions, for example. Of such, this method demonstrates potential within sensing applications for both medical and environmental fields.

Here we use a polyurethane tunable nanopore integrated into a resistive pulse sensing technique to characterize nanoparticles surface chemistry via the measurement of particle translocation velocities, which can be used to determine the zeta potential of individual nanoparticles.

Nanopore technologies, known collectively as Resistive Pulse Sensors (RPS), are being used to detect, quantify and characterize proteins, molecules and ...

Using Extraordinary Optical Transmission to Quantify Cardiac Biomarkers in Human Serum

For a biosensing platform to have clinical relevance in point-of-care (POC) settings, assay sensitivity, reproducibility, and ability to reliably monitor analytes against the background of human serum are crucial.
Nanoimprinting lithography (NIL) was used to fabricate, at a low cost, sensing areas as large as 1.5 mm x 1.5 mm. The sensing surface was made of high-fidelity arrays of nanoholes, each with an area of about 140 nm2. The great reproducibility of NIL made it possible to employ a one-chip, one-measurement strategy on 12 individually manufactured surfaces, with minimal chip-to-chip variation. These nanoimprinted localized surface plasmon resonance (LSPR) chips were extensively tested on their ability to reliably measure a bioanalyte at concentrations varying from 2.5 to 75 ng/mL amidst the background of a complex biofluid-in this case, human serum. The high fidelity of NIL enables the generation of large sensing areas, which in turn eliminates the need for a microscope, as this biosensor can be easily interfaced with a commonly available laboratory light source. These biosensors can detect cardiac troponin in serum with a high sensitivity, at a limit of detection (LOD) of 0.55 ng/mL, which is clinically relevant. They also show low chip-to-chip variance (due to the high quality of the fabrication process). The results are commensurable with widely used enzyme-linked immunosorbent assay (ELISA)-based assays, but the technique retains the advantages of an LSPR-based sensing platform (i.e., amenability to miniaturization and multiplexing, making it more feasible for POC applications).

This work describes a nanoimprinting lithography method to fabricate high-quality sensing arrays that work on the principle of extraordinary optical transmission. The biosensor is low-cost, robust, easy to use, and can detect cardiac troponin I in serum at clinically relevant concentrations (99th percentile cutoff &#8764;10-400 pg/mL, depending on the assay).

For a biosensing platform to have clinical relevance in point-of-care (POC) settings, assay sensitivity, reproducibility, and ability to reliably monitor ...

Targeting Neuronal Fiber Tracts for Deep Brain Stimulation Therapy Using Interactive, Patient-Specific Models

Deep brain stimulation (DBS), which involves insertion of an electrode to deliver stimulation to a localized brain region, is an established therapy for movement disorders and is being applied to a growing number of disorders. Computational modeling has been successfully used to predict the clinical effects of DBS; however, there is a need for novel modeling techniques to keep pace with the growing complexity of DBS devices. These models also need to generate predictions quickly and accurately. The goal of this project is to develop an image processing pipeline to incorporate structural magnetic resonance imaging (MRI) and diffusion weighted imaging (DWI) into an interactive, patient specific model to simulate the effects of DBS. A virtual DBS lead can be placed inside of the patient model, along with active contacts and stimulation settings, where changes in lead position or orientation generate a new finite element mesh and solution of the bioelectric field problem in near real-time, a timespan of approximately 10 seconds. This system also enables the simulation of multiple leads in close proximity to allow for current steering by varying anodes and cathodes on different leads. The techniques presented in this paper reduce the burden of generating and using computational models while providing meaningful feedback about the effects of electrode position, electrode design, and stimulation configurations to researchers or clinicians who may not be modeling experts.

The goal of this project is to develop an interactive, patient-specific modeling pipeline to simulate the effects of deep brain stimulation in near real-time and provide meaningful feedback as to how these devices influence neural activity in the brain.

Deep brain stimulation (DBS), which involves insertion of an electrode to deliver stimulation to a localized brain region, is an established therapy for ...

Screening and Identification of Small Peptides Targeting Fibroblast Growth Factor Receptor2 using a Phage Display Peptide Library

The human Fibroblast Growth Factor Receptor (FGFR) family comprises four members, namely, FGFR1, FGFR2, FGFR3, and FGFR4, that are involved in various biological activities including cell proliferation, survival, migration and differentiation. Several aberrations in the FGFR signaling pathway, owing to mutations or gene amplification events, have been identified in various types of cancers. Hence, recent research has focused on developing strategies involving therapeutic targeting of FGFRs. Current FGFR inhibitors at various stages of pre-clinical and clinical development include either small molecule inhibitors of tyrosine kinases or monoclonal antibodies, with only a few peptide- based inhibitors in the pipeline. Here, we provide a protocol using phage display technology to screen small peptides as antagonists of FGFR2. Briefly, a library of phage-displayed peptides was incubated in a plate coated with FGFR2. Subsequently, unbound phage was washed off by TBST (TBS + 0.1% [v/v] Tween-20), and bound phage was eluted with 0.2 M glycine-HCl buffer (pH 2.2). The eluted phage was further amplified and used as input for the next round of biopanning. Following three rounds of biopanning, the peptide sequences of individual phage clones were identified by DNA sequencing. Finally, the screened peptides were synthesized and analyzed for affinity and biological activity.

Herein, we present a detailed protocol for screening small peptides that bind to FGFR2 using a phage display peptide library. We further analyze the affinity of the selected peptides toward FGFR2 in vitro and its ability to suppress cell proliferation.

The human Fibroblast Growth Factor Receptor (FGFR) family comprises four members, namely, FGFR1, FGFR2, FGFR3, and FGFR4, that are involved in various ...