The funding for this project was provided solely from institutional or departmental resources.

NOTE: The University of Nebraska Medical Center Institutional Review Board determined that our study did not constitute human subject research. The local IRB obtained ethical approval and waiver of informed consent. Complete anonymization of imaging data was done before analysis per the hospital de-identification protocol.
1. Data
<ol>
	<li>Obtain a CT scan capturing the anatomy of interest for the planned task trainer. Be careful to take into consideration the working volume limitations of the 3D printer used and required landmarks for procedural steps.</li>
	<li>If the scan is obtained in a Digital Imaging and Communications in Medicine format (DICOM), convert to a Neuroimaging Informatics Technology Initiative (NiFTi)15 format (.nii).</li>
</ol>
2. Segmentation
<ol>
	<li>Use 3D Slicer software (http://www.slicer.org) to segment the CT images. Import the NIfTi file from Step 1.2 into 3D Slicer.</li>
	<li>Select the Segment Editor module to generate the segments needed to model the trainer.
	<ol>
		<li>Add one segment for the 1) Bone and 2) Tissue components of the task trainer. 
		NOTE: Development of some trainers, such as those used to train chest tube insertion, may require additional segments.</li>
		<li>Select segment 1) Bone. Using the Threshold Effect, change the intensity range until the defined &#34;window&#34; range identifies the Bone component of interest. 
		NOTE: For bone segments the usual range is between 100 and 175 HU (Hounsfield Units) to the available maximum value and for tissue, which is typically -256 HU to the available maximum.</li>
		<li>Use the Threshold function to highlight the 1) Bone component and apply it to the scan using the Apply command.</li>
		<li>Use the Scissors function to remove any areas of the scan not needed to create the task trainer. Use care to ensure that the bone marrow space remains hollow for IO trainers. 
		NOTE: This step is the first reduction of the segment of interest to the desired dimensions of the trainer. The build volume limitations of the 3D printer to be used should be considered here; however the segment may be further reduced in section 3.</li>
	</ol>
	</li>
	<li>Repeat steps 2.2.1-2.2.4 for the 2) Tissue component.</li>
	<li>Using the Segmentations module; export each component as an STL file.</li>
</ol>
3. 3D Modeling
<ol>
	<li>Use AutoDesk Meshmixer to crop the 3D segments further and reduce the resolution of each segment, in terms of the number of geometric elements, for optimal performance within Fusion360.
	<ol>
		<li>Confirm that imported STL files have the correct triangle normal orientation. Ensure the normals of each triangle point in the direction of the outer surface of the mesh. If the triangle orientation is incorrect, flip the triangle normal by performing the Select | Modify | Select All function and then the Select | Edit | Flip Normals function.</li>
		<li>Eliminate unwanted structures (e.g., unwanted segments of tissue or vasculature captured by the CT due to the use of contrast) of the imported STL Segments, and refine the models needed to create the task trainer. To refine the model by removing unwanted structures within the segments that may have been inadvertently included within the threshold range of the exported segment, use the Select operation, select the triangles on the undesired structures, then Edit | Discard.</li>
		<li>Following 3.1.2, use the Edit | Plane Cut tool to crop the model to fit within the confines of the 3D printer build volume. To reduce the computational overhead incurred due to excessive geometric resolution, reduce the number of triangles used to define the model to allow for optimal performance in Fusion360. Click on Select, double-click anywhere on the mesh to select the entire mesh, then Edit | Reduce. For Reduce Target, reduce to a Triangle Budget of under approximately 10,000 faces. 
		NOTE: The printer currently used by the authors has a maximum build volume of 250 x 210 x 210 mm; thus the model was cut to a maximum long-axis length of 220-230 mm to allow the mold to fit within the printer&#39;s build volume. The printer&#39;s build volume should dictate the long-axis length by making the model approximately 20-30 mm shorter. The geometry can easily be reduced to ~10K triangles without loss of clinically relevant detail to develop high-fidelity task trainers.</li>
		<li>Eliminate or reduce holes and surface irregularities using the Select tool. Once the triangles of the mesh around the defect are selected, use the command Select | Edit| Erase&#38;Fill to improve surface holes and irregularities.Export and save the finished models using the STL file type. 
		NOTE: The outer surface of the target bone for the interosseous line task trainers requires complete closing; otherwise, the melted tissue media will enter the marrow space and degrade the task trainer performance.</li>
	</ol>
	</li>
	<li>Use AutoDesk Fusion360, and import the bone and tissue models by adding the .STL files into the workspace as a mesh using the Insert | Insert Mesh command.
	<ol>
		<li>Convert the imported meshes into BRep solids by disabling the Fusion360 timeline and reducing the number of triangles in the target mesh to &#60;10,000.Select the imported Mesh Body and right-click. Choose the Mesh to BRep option. After the meshes have been converted to BReps solids, resume the Fusion360 timeline.</li>
		<li>Modify the solid to create the Task Trainer&#39;s mold by splitting the rectangular solid along the long axis of the Tissue BRep. 
		NOTE: The mold is created around the Tissue BRep by using the sketch feature to build a cube or rectangular solid that encompasses the Tissue solid. The mold size should be modified to meet the maximum build volume of the selected 3D printer. As the mold is split in two, the longest dimension printed may not be the final mold&#39;s largest dimension as they are joined.</li>
		<li>Select 2-3 locations for support pins, and place the pre-designed assembly group components to fix the task trainer&#39;s bones. Make sure that the locations selected for the support pins have an ample support structure in the bone around the head of the pin. 
		NOTE: The bone around the pin head selected does not need to be perfectly uniform as the assembly group also contains a solid cylindrical support structure, which will be fused with the bone. This structure adequately supports the head of the pin and preserves correct anatomic placement of the bones within the tissue media.</li>
		<li>Import and position a bone plug onto the open marrow space of the Bone BRep to prevent tissue media from entering the marrow space, and keep the simulated bone marrow from draining out.</li>
		<li>Generate an opening (typically 4-6 cm in diameter) through the molds in the space represented by the Tissue BRep solid to permit pouring the liquid tissue media into the mold.</li>
		<li>Once the components of the pre-designed assembly groups are positioned to fix the bones in space, perform Boolean Combine functions to either add or cut the various assembly groups into the models.
		<ol>
			<li>Perform a mirror of the objects before step 3.2.6 to make the task trainer for the ipsilateral side. Repeat steps 3.2.3-3.2.5 before 3.2.6.</li>
		</ol>
		</li>
		<li>Export the final components for printing. Select the desired body within the workspace and generate an STL file via right-click | Save As STL.</li>
	</ol>
	</li>
</ol>
4. 3D Printing
<ol>
	<li>Using Simplify 3D, position the STL file on the bed of the 3D printer so that the slicing program may generate the GCODE required to print the item. Print the components with Poly-lactic Acid (PLA) 3D printer media filament using a 0.4 mm nozzle at a hot end temperature of 210 &#176;C. Make sure that the settings utilize 4 top and bottom layers and 3 perimeter shells.</li>
	<li>Orient the bones vertically to minimize the required support material within the marrow cavity. Print using a raft, 0.2 mm layer height, 20% infill, and full support material (from the print bed and within the print). When printing the tissue molds, orient the mold components with the tissue surface facing up. Print the tissue molds without a raft, 0.3 mm layer height, 15% infill, and full support material.</li>
	<li>Arrange the support pins and other components to minimize support material-print all pin support parts with a raft, 0.2 mm layer height, and 20% infill. Print the threaded components without support material at a reduced speed, to maximize the fidelity of the thread structures.</li>
	<li>Once each component&#39;s parameters are selected, prepare and export the GCODE file generated by Simplify 3D to an SD card.Using a Prusa i3 MK3, select the saved GCODE file from the SD card and print with 1.75mm PLA 3D printer media filament.</li>
</ol>
5. Assembly
<ol>
	<li>Prepare the tissue medium. 
	NOTE: The trainee&#39;s current level of skill mastery may dictate whether opaque or transparent tissue medium is required. Transparent medium allows the trainee to visually track their progress during IO insertion and more easily identify bony landmarks, while opaque medium better simulates actual clinical experience.
	<ol>
		<li>Measure the following components to be used to create the tissue media, and set aside (these quantities may be scaled as needed) 260 g of unflavored gelatin; if required, 140 g of finely ground psyllium husk fiber, orange-flavored, sugar-free (omit this step to create a transparent medium); 42 g of 4% w/v chlorhexidine. 
		NOTE: Psyllium husk fiber may be used to make an opaque medium. This component should be added immediately after the gelatin if an opaque medium is desired16.</li>
		<li>Heat 1000 mL of water (tap is acceptable) to 85 &#176;C.Add the water to a mixing container several times larger than the volume of ingredients, such as an 18.9 L bucket.
		<ol>
			<li>While vigorously mixing the tissue medium solution, add the gelatin, psyllium husk fiber, and chlorhexidine solution to the water, in order, and wait before adding the next ingredient after the previous one is incorporated. 
			NOTE: Do not add psyllium husk fiber if making transparent medium.</li>
		</ol>
		</li>
		<li>Heat the mixture in a 71 &#176;C water bath for a minimum of 4 h to allow the bubbles to dissipate from the solution. Place the mixing container in the hot water bath directly, or transfer the mixture to a separate container, such as plastic storage bags.</li>
		<li>Prepare the tissue medium for pouring into the assembled mold. Ensure that the mixture is homogeneous and fluid. Maintain the temperature of the mixture at 46 &#176;C. 
		NOTE: If the tissue medium is not immediately needed, it may be stored at 4 &#176;C or -20 &#176;C within a storage container until needed.</li>
	</ol>
	</li>
	<li>Prepare the simulated bone marrow solution. 
	NOTE: The simulated bone marrow solution may be prepared in advance and stored in a covered container at room temperature until ready for use.
	<ol>
		<li>Measure and thoroughly mix 100 g of cool water (tap is fine); 100 g of ultrasound gel; and 5 mL of red food coloring (optional, used to improve simulation). Ensure that the final product is thick but fluid enough to transfer quickly.</li>
	</ol>
	</li>
	<li>Secure the bone to the bottom of the mold, and assemble the mold.
	<ol>
		<li>Spray each side of the mold&#39;s inner surfaces with a non-silicone-based releasing agent, such as non-stick cooking spray.Secure the bone using the support pins to maintain the correct position within the tissue space. Secure the bones/pins to the bottom of the mold.</li>
		<li>Align the top of the mold to the bottom portion, and secure the two halves of the mold together. Verify the bone plug is in position to prevent tissue medium entering the marrow space during pouring.</li>
	</ol>
	</li>
	<li>Position the mold such that the opening is facing up, and pour the 46 &#176;C tissue medium into the mold&#39;s cavity.Remedy any leakage of the tissue medium from the mold using an inverted air duster canister by directly spraying the warm tissue medium with the canister to cool it quickly.Transfer the filled mold to a 4 &#176;C refrigerator for a minimum of 6 h, or until the tissue medium has set.</li>
	<li>Disassemble the mold, and remove the task trainer and the support pins.Remove the bone plug, fill the marrow space with simulated &#39;bone marrow&#39; created in 5.2, and replace the bone plug. Place the task trainers in a plastic storage bag, and store the assembly at either 4 &#176;C or -20 &#176;C until needed for training.</li>
</ol>
6. Task training
<ol>
	<li>Remove the task trainer from storage and allow it to reach room temperature. If not already in place, add simulated bone marrow material from step 5.2 per instruction in 5.5. 
	NOTE: Allowing the trainer to warm to room temperature improves the simulation experience.</li>
	<li>Perform training on the task trainers. Instruct the trainees to place IO needles (Figure 2A), and aspirate simulated bone marrow (Figure 2B) as per the IO line placement&#39;s usual steps.</li>
	<li>Following training, disassemble the task trainers to reclaim tissue, the medium, and the bones. 
	NOTE: After manipulation, the bones of the IO trainer will have holes created by insertion of the IO line canula. These holes may be either filled with PLA using a handheld 3D printer pen, or alternately the bones may be discarded.</li>
	<li>Reassemble and reuse reclaimed materials for subsequent training as per section 5.Alternatively, melt the tissue medium down, reclaim per 5.1.4, and store at either 4 &#176;C or -20 &#176;C, if not immediately needed.</li>
</ol>

<ol>
	<li>Farrow, D. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Reducing+the+risks+of+military+aircrew+training+through+simulation+technology.">Reducing the risks of military aircrew training through simulation technology.</a> Performance and Instruction. 21 (2), 13-18 (1982).</li><li>Lateef, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation-based+learning:+Just+like+the+real+thing.">Simulation-based learning: Just like the real thing.</a> Journal of Emergencies, Trauma, Shock. 3 (4), 348-352 (2010).</li><li>Gaba, D. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Crisis+resource+management+and+teamwork+training+in+anaesthesia.">Crisis resource management and teamwork training in anaesthesia.</a> British Journal of Anaesthesia. 105 (1), 3-6 (2010).</li><li>Al-Elq, A. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation-based+medical+teaching+and+learning.">Simulation-based medical teaching and learning.</a> Journal of Family &amp; Community Medicine. 17 (1), 35-40 (2010).</li><li>Hays, R. T., Singer, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Simulation fidelity in training system design: Bridging the gap between reality and training. , (2012).</li><li>Green, M., Tariq, R., Green, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Improving+patient+safety+through+simulation+training+in+anesthesiology:+Where+are+we.">Improving patient safety through simulation training in anesthesiology: Where are we.</a> Anesthesiology Research and Practice. , 4237523 (2016).</li><li>Olympio, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation+saves+lives.">Simulation saves lives.</a> American Society of Anesthesiologists Newsletter. , 15-19 (2001).</li><li>Murphy, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation-based+multidisciplinary+team+training+decreases+time+to+critical+operations+for+trauma+patients.">Simulation-based multidisciplinary team training decreases time to critical operations for trauma patients.</a> Injury. 49 (5), 953-958 (2018).</li><li>Jensen, A. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation-based+training+is+associated+with+lower+risk-adjusted+mortality+in+ACS+pediatric+TQIP+centers.">Simulation-based training is associated with lower risk-adjusted mortality in ACS pediatric TQIP centers.</a> Journal of Trauma and Acute Care Surgery. 87 (4), 841-848 (2019).</li><li>Gupta, A., Peckler, B., Schoken, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Introduction+of+hi-fidelity+simulation+techniques+as+an+ideal+teaching+tool+for+upcoming+emergency+medicine+and+trauma+residency+programs+in+India.">Introduction of hi-fidelity simulation techniques as an ideal teaching tool for upcoming emergency medicine and trauma residency programs in India.</a> Journal of Emergencies, Trauma, and Shock. 1 (1), 15-18 (2008).</li><li>Risser, D. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+potential+for+improved+teamwork+to+reduce+medical+errors+in+the+emergency+department.">The potential for improved teamwork to reduce medical errors in the emergency department.</a> Annals of Emergency Medicine. 34 (3), 373-383 (1999).</li><li>Shapiro, M. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation+based+teamwork+training+for+emergency+department+staff:+Does+it+improve+clinical+team+performance+when+added+to+an+existing+didactic+teamwork+curriculum.">Simulation based teamwork training for emergency department staff: Does it improve clinical team performance when added to an existing didactic teamwork curriculum.</a> Quality and Safety in Health Care. 13 (6), 417-421 (2004).</li><li>Schebesta, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Degrees+of+reality:+Airway+anatomy+of+high-fidelity+human+patient+simulators+and+airway+trainers.">Degrees of reality: Airway anatomy of high-fidelity human patient simulators and airway trainers.</a> Anesthesiology. 116 (6), 1204-1209 (2012).</li><li>Crofts, J. F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Training+for+shoulder+dystocia:+A+trial+of+simulation+using+low-fidelity+and+high-fidelity+mannequins.">Training for shoulder dystocia: A trial of simulation using low-fidelity and high-fidelity mannequins.</a> Obstetrics and Gynecology. 108 (6), 1477-1485 (2006).</li><li>Cox, R. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+(sort+of)+new+image+data+format+standard:+NiFTI-1.">A (sort of) new image data format standard: NiFTI-1.</a> 10th Annual Meeting of the Organization for Human Brain Mapping. , 22 (2004).</li><li>Bude, R., Adler, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+easily+made,+low-cost,+tissue-like+ultrasound+phantom+material.">An easily made, low-cost, tissue-like ultrasound phantom material.</a> Journal of Clinical Ultrasound. 23 (4), 271-273 (1995).</li><li>Fisher, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Clinical+skills+temporal+degradation+assessment+in+undergraduate+medical+education.">Clinical skills temporal degradation assessment in undergraduate medical education.</a> Journal of Advances in Medical Education &amp; Professionalism. 6 (1), 1-5 (2018).</li><li>Buzink, S. N., Goossens, R. H., Schoon, E. J., de Ridder, H., Jakimowicz, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Do+basic+psychomotor+skills+transfer+between+different+image-based+procedures.">Do basic psychomotor skills transfer between different image-based procedures.</a> World Journal of Surgery. 34 (5), 933-940 (2010).</li></ol>

The authors have nothing to disclose.

In this protocol we detail a 3D task trainer's development process to train the infrequently performed and life-saving procedure of IO line placement. This self-guided protocol uses 3D printing to produce the bulk of the model structures, while the remainder of the components used to assemble the task trainer are ubiquitous, easily obtainable, and non-toxic materials that may be reclaimed and reused. The 3D task trainer is low-cost and requires minimum expertise to create and assemble. We have successfully used our 3D IO...

Patient care competency of procedural skills is a critical component for developing trainees in civilian and military healthcare1,2 environments. Procedural skills development is particularly important for procedure-intensive specialties such as anesthesiology3 and front-line medical personnel. Task trainers may be used to rehearse numerous procedures with skill levels ranging from those of a first-year medical student or medical technician to a senior resident or fellow. While many medical procedures require significant training to complete, the task presented here-placement of an interosseous (IO) line-is straightforward and requires less technical skill. Successful placement of an IO line can be accomplished after a relatively short period of training. The use of simulation during medical training, which includes the use of task trainers, is recognized as a tool to gain technical procedural skills through the repetition and the rehearsal of a clinical procedure in a safe, low-stress environment, before ultimately performing the procedure on patients2,4,5.
Understandably so, simulation training in medical education environments has become widely accepted and appears to be a mainstay, despite the paucity of data regarding any impact on patient outcomes6,7. Additionally, recent publications demonstrate that simulation improves team performance and patient outcomes as the result of improved team dynamics and decision-making. Still, there is little data to suggest that simulation improves the time or success rate to perform critical, life-saving procedures8,9 suggesting that simulation is complex and multifaceted in the education of health care providers. In patients where standard intravenous access is not possible or indicated, IO line placement may be used to achieve vascular access quickly, requiring minimal skill. Timely and successful performance of this procedure is critical, particularly in the perioperative environment or a trauma scenario10,11,12. Because IO line placement is an infrequently performed procedure in the perioperative area and can be a life-saving procedure, training in a non-clinical environment is critical. An anatomically accurate task trainer specific to IO line placement is an ideal tool for offering predictable training frequency and skills development for this procedure.
Although widely used, currently available commercial task trainers suffer from several significant drawbacks. First, task trainers that allow for multiple attempts of a procedure are costly, not only for the initial purchase of the task trainer but also for replenishing the replaceable parts such as silicone skin patches. The result is often infrequently replaced parts, leaving prominent landmarks that provide the trainee a suboptimal training experience; patients will not come pre-marked where one should do the procedure. Another drawback is that the high cost of traditional task trainers can result in limited access by users when the devices are &#39;locked up&#39; in protected storage locations to prevent loss or damage to the devices. The result is requiring more rigorously and less available scheduled practice time, limiting their use can certainly make unscheduled training difficult. Finally, most trainers are considered low-fidelity5,13,14 and use only representative anatomy, potentially leading to inappropriate psychomotor skills development or training scars. Low-fidelity trainers also make the thorough assessment of skill acquisition, mastery, and degradation very difficult as training on a low-fidelity device may not adequately mimic the actual real-world procedure.
Representative anatomy also impedes the proper evaluation of the acquisition and mastery of psychomotor skills. Moreover, assessing the transfer of psychomotor skills between simulated medical environments to patient care becomes nearly impossible if some of the psychomotor skills are not reflected in the clinical task. This results in the prevention of consensus on the ability of medical simulation and training to affect patient outcomes. To overcome the challenges of cost, anatomical accuracy, and access, we have developed a low-cost, high-fidelity IO line task trainer. The task trainer is designed from an actual patient&#39;s CT scan, resulting in accurate anatomy (Figure 1). The materials used are ubiquitous and easy to obtain, with components that are relatively easy to reclaim. Compared to many other commercially available trainers, the modest cost of the task trainer design described here dramatically reduces the desire to sequester the trainers in a less accessible, protected location and makes multiple repetitions without leading landmarks possible.

<table><tbody><tr><td>3D printer filament, poly-lactic acid (PLA), 1.75 mm</td><td>N/A / Hatchbox</td><td></td><td>Base for 3D printing molds, bone structures, and bone / mold hardware</td></tr><tr><td>3D printer, Original Prusa i3 MK3</td><td>Prusa</td><td></td><td>To print molds, bone structures, and bone / mold hardware</td></tr><tr><td>bolts, 1/4&amp;rdquo;, flat / countersunk or round head, various lengths</td><td>N/A</td><td></td><td>Hardware used to hold mold casing halves together during casting</td></tr><tr><td>Bucket, 5 gallon, plastic</td><td>N/A</td><td></td><td>To hold tissue media during media preparation</td></tr><tr><td>chlorhexidine, 4% solution w/v</td><td></td><td></td><td>Animicrobial additive for tissue media</td></tr><tr><td>drill, household 3/8&amp;rsquo; chuck</td><td>N/A</td><td></td><td>To stir tissue media during media preparation</td></tr><tr><td>food coloring, red (optional)</td><td>N/A</td><td></td><td>Coloring additive for simulated bone marrow</td></tr><tr><td>gelatin, unflavored</td><td>Knox</td><td></td><td>Base for tissue media</td></tr><tr><td>hex nuts, 1/4&amp;rdquo;</td><td>N/A</td><td></td><td>Hardware used to hold mold casing halves together during casting</td></tr><tr><td>Non-stick cooking spray</td><td>N/A</td><td></td><td>Mold releasing agent</td></tr><tr><td>plastic bags, ziplock</td><td>Ziplock</td><td></td><td>To store tissue media</td></tr><tr><td>psyllium husk fiber, finely ground, orange flavored, sugar free (optional)</td><td>Procter &amp;amp; Gamble</td><td>Metamucil</td><td>Opacity / Echogenicity additive for tissue media</td></tr><tr><td>screwdriver, flat / Phillips (matching bolt hardware)</td><td>N/A</td><td></td><td>To tighten mold casing hardware</td></tr><tr><td>silicone gasket cord stock, 3 mm, round, various lengths</td><td>N/A</td><td></td><td>Gasket media for mold casings</td></tr><tr><td>spray adhesive, Super 77 (optional)</td><td>3M</td><td></td><td>Agent used to improve bed adhesion during 3D printing</td></tr><tr><td>stirring paddle / rod</td><td></td><td></td><td>To stir tissue media during media preparation</td></tr><tr><td>turkey baster, household, 60 mL</td><td>N/A</td><td></td><td>To inject simulated bone marrow into bone marrow cavity</td></tr><tr><td>ultrasound gel</td><td></td><td></td><td>Base for simulated bone marrow</td></tr><tr><td>water, tap</td><td></td><td></td><td>Used in both tissue media and simulated bone marrow</td></tr></tbody></table>

creation of a high-fidelity, low-cost, intraosseous line placement task trainer via 3d printing

The description of procedural task trainers includes their use as a training tool to hone technical skills through repetition and rehearsal of procedures in a safe environment before ultimately performing the procedure on a patient. Many procedural task trainers available to date suffer from several drawbacks, including unrealistic anatomy and the tendency to develop user-created &#39;landmarks&#39; after the trainer tissue undergoes repeated manipulations, potentially leading to inappropriate psychomotor skill development. To ameliorate these drawbacks, a process was created to produce a high-fidelity procedural task trainer, created from anatomy obtained from computed tomography (CT) scans, that utilize ubiquitous three-dimensional (3D) printing technology and off-the-shelf commodity supplies.
This method includes creating a 3D printed tissue mold capturing the tissue structure surrounding the skeletal element of interest to encase the bony skeletal structure suspended within the tissue, which is also 3D printed. A tissue medium mixture, which approximates tissue in both high-fidelity geometry and tissue density, is then poured into a mold and allowed to set. After a task trainer has been used to practice a procedure, such as intraosseous line placement, the tissue media, molds, and bones are reclaimable and may be reused to create a fresh task trainer, free of puncture sites and manipulation defects, for use in subsequent training sessions.

Following the protocol, the modeling of the task trainer utilized a CT scan of a de-identified patient. Segmentation of the CT images utilized 3D Slicer software and Auto Meshmixer for 3D modeling. For 3D printing, both 3D Simplify and the Prusa i3 MK3 were used (Figure 1). Subsequently, we completed the assembly of the 3D-printed parts, prepared the tissue media mixture, and poured the media mixture into the assembled task trainer mold. Following a training period with the task trainer, the...

Watch this Scientific Journal Video about Creation of a High-Fidelity, Low-Cost, Intraosseous Line Placement Task Trainer via 3D Printing at JoVE.com

Creation of a High-Fidelity, Low-Cost, Intraosseous Line Placement Task Trainer via 3D Printing

We describe a procedure to process computed tomography (CT) scans into high-fidelity, reclaimable, and low-cost procedural task trainers. The CT scan identification processes, export, segmentation, modeling, and 3D printing are all described, along with the issues and lessons learned in the process.

The description of procedural task trainers includes their use as a training tool to hone technical skills through repetition and rehearsal of procedures ...

creation-high-fidelity-low-cost-intraosseous-line-placement-task

Research

JoVE Journal

Medicine

2.0K Views.  University of Nebraska Medical Center. We describe a procedure to process computed tomography (CT) scans into high-fidelity, reclaimable, and low-cost procedural task trainers. The CT scan identification processes, export, segmentation, modeling, and 3D printing are all described, along with the issues and lessons learned in the process. 

Video: Creation of a High-Fidelity, Low-Cost, Intraosseous Line Placement Task Trainer via 3D Printing

Application of 3D Printing in the Construction of Burr Hole Ring for Deep Brain Stimulation Implants

3D printing has been widely applied in the medical field since the 1980s, especially in surgery, such as preoperative simulation, anatomical learning and surgical training. This raises the possibility of using 3D printing to construct a neurosurgical implant. Our previous works took the construction of the burr hole ring as an example, described the process of using softwares like computer aided design (CAD), Pro/Engineer (Pro/E) and 3D printer to construct physical products. That is, a total of three steps are required, the drawing of 2D-image, the construction of 3D-image of burr hole ring, and using a 3D printer to print the physical model of burr hole ring. This protocol shows that the burr hole ring made of carbon fiber can be rapidly and accurately molded by 3D printing. It indicated that both CAD and Pro/E softwares can be used to construct the burr hole ring via integrating with the clinical imaging data and further applied 3D printing to make the individual consumables.

Here, we present a protocol to demonstrate 3D printing in the construction of deep brain stimulation implants.

3D printing has been widely applied in the medical field since the 1980s, especially in surgery, such as preoperative simulation, anatomical learning and ...

Behavior

Creation of Patient-Specific Silicone Cardiac Models with Applications in Pre-surgical Plans and Hands-on Training

Three dimensional&#160;models can be a valuable tool for surgeons as they develop surgical plans and medical fellows as they learn about complex cases. In particular, 3D models can play an important role in the field of cardiology, where complex congenital heart diseases occur. While many 3D printers can provide anatomically correct and detailed models, existing 3D printing materials fail to replicate myocardial tissue properties and can be extremely costly. This protocol aims to develop a process for the creation of patient-specific models of complex congenital heart defects using a low-cost silicone that more closely matches cardiac muscle properties. With improved model fidelity, actual surgical procedural training could occur in advance of the procedure. Successful creation of cardiac models begins with the segmentation of radiologic images to generate a virtual blood pool (blood that fills the chambers of the heart) and myocardial tissue mold. The blood pool and myocardial mold are 3D printed in acrylonitrile butadiene styrene (ABS), a plastic dissolvable in acetone. The mold is assembled around the blood pool, creating a negative space simulating the myocardium. Silicone with a shore hardness of 2A is poured into the negative space and allowed to cure. The myocardial mold is removed, and the remaining silicone/blood pool model is submerged in acetone. The described process results in a physical model in which all cardiac features, including intra-cardiac defects, are represented with more realistic tissue properties and are more closely approximated than a direct 3D printing approach. The successful surgical correction of a model with a ventricular septal defect (VSD) using a GORE-TEX patch (standard surgical intervention for defect) demonstrates the utility of the method.

Patient-specific models improve surgeon and fellow confidence when developing or learning surgical plans. Three-dimensional (3D) printers generate adequate detail for surgical preparation, but fail to replicate tissue haptic fidelity. A protocol is presented detailing the creation of patient-specific, silicone cardiac models, combining 3D printing precision with simulated silicone tissue.

Three dimensional&#160;models can be a valuable tool for surgeons as they develop surgical plans and medical fellows as they learn about complex cases. In ...

Bioengineering

3D Printing of Preclinical X-ray Computed Tomographic Data Sets

Three-dimensional printing allows for the production of highly detailed objects through a process known as additive manufacturing. Traditional, mold-injection methods to create models or parts have several limitations, the most important of which is a difficulty in making highly complex products in a timely, cost-effective manner.1 However, gradual improvements in three-dimensional printing technology have resulted in both high-end and economy instruments that are now available for the facile production of customized models.2 These printers have the ability to extrude high-resolution objects with enough detail to accurately represent in vivo images generated from a preclinical X-ray CT scanner. With proper data collection, surface rendering, and stereolithographic editing, it is now possible and inexpensive to rapidly produce detailed skeletal and soft tissue structures from X-ray CT data. Even in the early stages of development, the anatomical models produced by three-dimensional printing appeal to both educators and researchers who can utilize the technology to improve visualization proficiency. 3, 4 The real benefits of this method result from the tangible experience a researcher can have with data that cannot be adequately conveyed through a computer screen. The translation of pre-clinical 3D data to a physical object that is an exact copy of the test subject is a powerful tool for visualization and communication, especially for relating imaging research to students, or those in other fields. Here, we provide a detailed method for printing plastic models of bone and organ structures derived from X-ray CT scans utilizing an Albira X-ray CT system in conjunction with PMOD, ImageJ, Meshlab, Netfabb, and ReplicatorG software packages.

Using modern plastic extrusion and printing technologies, it is now possible to quickly and inexpensively produce physical models of X-ray CT data taken in a laboratory. The three -dimensional printing of tomographic data is a powerful visualization, research, and educational tool that may now be accessed by the preclinical imaging community.

Three-dimensional printing allows for the production of highly detailed objects through a process known as additive manufacturing.  Traditional, ...

Biology

Combining Augmented Reality and 3D Printing to Display Patient Models on a Smartphone

Augmented reality (AR) has great potential in education, training, and surgical guidance in the medical field. Its combination with three-dimensional (3D) printing (3DP) opens new possibilities in clinical applications. Although these technologies have grown exponentially in recent years, their adoption by physicians is still limited, since they require extensive knowledge of engineering and software development. Therefore, the purpose of this protocol is to describe a step-by-step methodology enabling inexperienced users to create a smartphone app, which combines AR and 3DP for the visualization of anatomical 3D models of patients with a 3D-printed reference marker. The protocol describes how to create 3D virtual models of a patient&rsquo;s anatomy derived from 3D medical images. It then explains how to perform positioning of the 3D models with respect to marker references. Also provided are instructions for how to 3D print the required tools and models. Finally, steps to deploy the app are provided. The protocol is based on free and multi-platform software and can be applied to any medical imaging modality or patient. An alternative approach is described to provide automatic registration between a 3D-printed model created from a patient&rsquo;s anatomy and the projected holograms. As an example, a clinical case of a patient suffering from distal leg sarcoma is provided to illustrate the methodology. It is expected that this protocol will accelerate the adoption of AR and 3DP technologies by medical professionals.

Presented here is a method to design an augmented reality smartphone application for the visualization of anatomical three-dimensional models of patients using a 3D-printed reference marker.

Augmented reality (AR) has great potential in education, training, and surgical guidance in the medical field. Its combination with three-dimensional (3D) ...

3D Planning and Printing of Patient Specific Implants for Reconstruction of Bony Defects

We are in the midst of the 3D era in most aspects of life, and especially in medicine. The surgical discipline is one of the major players in the medical field using the constantly developing 3D planning and printing capabilities. Computer-assisted design (CAD) and computer assisted manufacturing (CAM) are used to describe the 3D planning and manufacturing of the product. The planning and manufacturing of 3D surgical guides and reconstruction implants is performed almost exclusively by engineers. As technology advances and software interfaces become more user-friendly, it raises a question regarding the possibility of transferring the planning and manufacturing to the clinician. The reasons for such a shift are clear: the surgeon has the idea of what he wants to design, and he also knows what is feasible and could be used in the operating room. It allows him to be prepared for any scenario/unexpected results during the operation and allows the surgeon to be creative and express his new ideas using the CAD software. The purpose of this method is to provide clinicians with the ability to create their own surgical guides and reconstruction implants. In this manuscript, a detailed protocol will provide a simple method for segmentation using segmentation software and implant planning using a 3D design software. Following the segmentation and stl file production using segmentation software, the clinician could create a simple patient specific reconstruction plate or a more complex plate with a cradle for bone graft positioning. Surgical guides can be created for accurate resection, hole preparation for proper reconstruction plate positioning or for bone graft harvesting and re-contouring. A case of lower jaw reconstruction following plate fracture and nonunion healing of a trauma sustained injury is detailed.

This protocol describes the use of 3D planning and printing for reconstruction of bony defects. We use segmentation tools to create 3D models followed by 3D design software to create patient specific implants for reconstruction purposes concomitant to ablative surgery or as a second stage.

We are in the midst of the 3D era in most aspects of life, and especially in medicine. The surgical discipline is one of the major players in the medical ...

Treatment of Facial Deformities using 3D Planning and Printing of Patient-Specific Implants

Technological advancements in surgical planning and patient-specific implants are constantly evolving. One can either adopt the technology to achieve better results, even in the less experienced hand, or continue without it. As technology develops and becomes more user-friendly, we believe it is time to allow the surgeon the option to plan his/her operations and create his/her own patient-specific surgical guides and fixation plates allowing him full control over the process. We present here a protocol for 3D planning of the operation followed by 3D planning and printing of surgical guides and patient-specific fixation implants. During this process we use two commercial computer-assisted design (CAD) software. We also use a fused deposition&#160;modeling printer for the surgical guides and a selective laser sintering printer for the titanium patient-specific fixation implants. The process includes computed tomography (CT) imaging acquisition, 3D segmentation of the skull and facial bones from the CT, 3D planning of the operations, 3D planning of patient-specific fixation implant according to the final position of the bones, 3D planning of surgical guides for performing an accurate osteotomy and preparing the bone for the fixation plates, and 3D printing of the surgical guides and the patient-specific fixation plates. The advantages of the method include full control over the surgery, planned osteotomies and fixation plates, significant reduction in price, reduction in operation duration, superior performance and highly accurate results. Limitations include the need to master the CAD programs.

As technology develops and becomes more user-friendly, planning of operations and patient-specific surgical guides and fixation plates should be performed by the surgeon. We present a protocol for 3D planning of orthognathic skeletal movements and 3D planning and printing of patient-specific fixation plates and surgical guides.

Technological advancements in surgical planning and patient-specific implants are constantly evolving. One can either adopt the technology to achieve ...

Development and Evaluation of 3D-Printed Cardiovascular Phantoms for Interventional Planning and Training

Catheter-based interventions are standard treatment options for cardiovascular pathologies. Therefore, patient-specific models could help training physicians&#39; wire-skills as well as improving planning of interventional procedures. The aim of this study was to develop a manufacturing process of patient-specific 3D-printed models for cardiovascular interventions.
To create a 3D-printed elastic phantom, different 3D-printing materials were compared to porcine biological tissues (i.e., aortic tissue) in terms of mechanical characteristics. A fitting material was selected based on comparative tensile tests and specific material thicknesses were defined. Anonymized contrast-enhanced CT-datasets were collected retrospectively. Patient-specific volumetric models were extracted from these datasets and subsequently 3D-printed. A pulsatile flow loop was constructed to simulate the intraluminal blood flow during interventions. Models&#39; suitability for clinical imaging was assessed by x-ray imaging, CT, 4D-MRI and (Doppler) ultrasonography. Contrast medium was used to enhance visibility in x-ray-based imaging. Different catheterization techniques were applied to evaluate the 3D-printed phantoms in physicians&#39; training as well as for pre-interventional therapy planning.
Printed models showed a high printing resolution (~30 &#181;m) and mechanical properties of the chosen material were comparable to physiological biomechanics. Physical and digital models showed high anatomical accuracy when compared to the underlying radiological dataset. Printed models were suitable for ultrasonic imaging as well as standard x-rays. Doppler ultrasonography and 4D-MRI displayed flow patterns and landmark characteristics (i.e., turbulence, wall shear stress) matching native data. In a catheter-based laboratory setting, patient-specific phantoms were easy to catheterize. Therapy planning and training of interventional procedures on challenging anatomies (e.g., congenital heart disease (CHD)) was possible.
Flexible patient-specific cardiovascular phantoms were 3D-printed, and the application of common clinical imaging techniques was possible. This new process is ideal as a training tool for catheter-based (electrophysiological) interventions and can be used in patient-specific therapy planning.

Here we present development of a mock circulation setup for multimodal therapy evaluation, pre-interventional planning, and physician-training on cardiovascular anatomies. With the application of patient-specific tomographic scans, this setup is ideal for therapeutic approaches, training, and education in individualized medicine.

Catheter-based interventions are standard treatment options for cardiovascular pathologies. Therefore, patient-specific models could help training ...

The Use of Mixed Reality in Custom-Made Revision Hip Arthroplasty: A First Case Report

The technology of 3D printing and visualization of anatomical structures is rapidly growing in various fields of medicine. A custom-made implant and mixed reality were used to perform complex revision hip arthroplasty in January 2019. The use of mixed reality allowed for a very good visualization of the structures and resulted in precise implant fixation. According to the authors' knowledge, this is the first described case report of the combined use of these two innovations. The diagnosis preceding the qualification for the procedure was the loosening of the left hip's acetabular component. Mixed reality headset and holograms prepared by engineers were used during the surgery. The operation was successful, and it was followed by early verticalization and patient rehabilitation. The team sees opportunities for technology development in joint arthroplasty, trauma, and orthopedic oncology.

A complex revision hip arthroplasty was performed using a custom-made implant and mixed reality technology. According to the authors&#39; knowledge, this is the first report of such procedure described in the literature.

The technology of 3D printing and visualization of anatomical structures is rapidly growing in various fields of medicine. A custom-made implant and mixed ...

A Personalized 3D-Printed Model for Preoperative Evaluation in Thyroid Surgery

The anatomic structure of the surgical area of thyroid cancer is complex. It is very important to comprehensively and carefully evaluate the tumor location and its relation with the capsule, trachea, esophagus, nerves, and blood vessels before operation. This paper introduces an innovative 3D-printed model establishment method based on computerized tomography (CT) DICOM images. We established a personalized 3D-printed model of the cervical thyroid surgery field for each patient who needed thyroid surgery to help clinicians evaluate the key points and difficulties of the surgery and select the operation methods of key parts as a basis. The results showed that this model is conducive to preoperative discussion and the formulation of operation strategies. In particular, as a result of the clear display of the recurrent laryngeal nerve and parathyroid gland locations in the thyroid operation field, injury to them can be avoided during surgery, the difficulty of thyroid surgery reduced, and the incidence of postoperative hypoparathyroidism and complications related to recurrent laryngeal nerve injury reduced too. Moreover, this 3D-printed model is intuitive and aids communication for the signing of informed consent by patients before surgery.

Here, a new method of establishing a personalized 3D-printed model for preoperative evaluation of thyroid surgery is proposed. It is conducive to preoperative discussion, reducing the difficulty of thyroid surgery.

The anatomic structure of the surgical area of thyroid cancer is complex. It is very important to comprehensively and carefully evaluate the tumor ...

3D Printing Model of a Patient's Specific Lumbar Vertebra

Selective dorsal rhizotomy (SDR) is a difficult, risky, and sophisticated operation, in which a laminectomy should not only expose an adequate surgical field of view but also protect the patient&#39;s spinal nerves from injury. Digital models play an important role in the pre-and intra-operation of SDR, because they can not only make doctors more familiar with the anatomical structure of the surgical site, but also provide precise surgical navigation coordinates for the manipulator. This study aims to create a 3D digital model of a patient-specific lumbar vertebra that can be used for planning, surgical navigation, and training of the SDR operation. The 3D printing model is also manufactured for more effective work during these processes.
Traditional orthopedic digital models rely almost entirely on computed tomography (CT) data, which is less sensitive to soft tissues. Fusion of the bone structure from CT and the neural structure from magnetic resonance imaging (MRI) is the key element for the model reconstruction in this study. The patient&#39;s specific 3D digital model is reconstructed for the real appearance of the surgical area and shows the accurate measurement of inter-structural distances and regional segmentation, which can effectively help in the preoperative planning and training of SDR. The transparent bone structure material of the 3D-printed model allows surgeons to clearly distinguish the relative relationship between the spinal nerve and the vertebral plate of the operated segment, enhancing their anatomical understanding and spatial sense of the structure. The advantages of the individualized 3D digital model and its accurate relationship between spinal nerve and bone structures make this method a good choice for preoperative planning of SDR surgery.

This study aims to create a 3D-printed model of a patient-specific lumbar vertebra, which contains both the vertebra and spinal nerve models fused from high-resolution computed tomography (HRCT) and MRI-Dixon data.

Selective dorsal rhizotomy (SDR) is a difficult, risky, and sophisticated operation, in which a laminectomy should not only expose an adequate surgical ...