Protocol of Electrochemical Test and Characterization of Aprotic Li-O<sub>2</sub> Battery

We demonstrate a method for electrochemical testing of an aprotic Li-O2 battery. An aprotic Li-O2 battery is made of a Li-metal anode, an aprotic ...

Argonne National Laboratory

Crosstown traffic: Further development of Li-O(2) batteries may eventually lead to their use in transportation applications. One problem that needs to be addressed is electrolyte decomposition, which has been partially mitigated by using ether- rather than carbonate-based solvents. The influence of oxygen crossover from the cathode to the anode on electrolyte, and lithium anode, decomposition in ether-based Li-O(2) batteries is investigated.

The effect of oxygen crossover on the anode of a Li-O(2) battery using an ether-based solvent: insights from experimental and computational studies.

The stability of lithium salts, especially in the presence of reduced oxygen species, O2 and H2O (even in a small amount), plays an important role in the cyclability and capacity of Li-O2 cells. This combined experimental and computational study provides evidence that the stability of the electrolyte used in Li-O2 cells strongly depends on the compatibility of lithium salts with solvent. In the case of the LiPF6-1NM3 electrolyte, the decomposition of LiPF6 occurs in the cell as evidenced by in situ XRD, FT-IR and XPS analysis, which triggers the decomposition of 1NM3 solvent due to formation of HF from the decomposition of LiPF6. These reactions lead to degradation of the electrolyte and cause poor cyclability of the cell. The same reactions are not observed when LiTFSI and LiCF3SO3 are used as the lithium salts in 1NM3 solvent, or LiPF6 is used in TEGDME solvent.

Compatibility of lithium salts with solvent of the non-aqueous electrolyte in Li-O2 batteries.

In this study, atomic layer deposition (ALD) was used to deposit nanostructured palladium on porous carbon as the cathode material for Li-O2 cells. Scanning transmission electron microscopy showed discrete crystalline nanoparticles decorating the surface of the porous carbon support, where the size could be controlled in the range of 2-8 nm and depended on the number of Pd ALD cycles performed. X-ray absorption spectroscopy at the Pd K-edge revealed that the carbon supported Pd existed in a mixed phase of metallic palladium and palladium oxide. The conformality of ALD allowed us to uniformly disperse the Pd catalyst onto the carbon support while preserving the initial porous structure. As a result, the charging and discharging performance of the oxygen cathode in a Li-O2 cell was improved. Our results suggest that ALD is a promising technique for tailoring the surface composition and structure of nanoporous supports in energy storage devices.

Synthesis of porous carbon supported palladium nanoparticle catalysts by atomic layer deposition: application for rechargeable lithium-O2 battery.

The lithium-oxygen battery, of much interest because of its very high-energy density, presents many challenges, one of which is a high-charge overpotential that results in large inefficiencies. Here we report a cathode architecture based on nanoscale components that results in a dramatic reduction in charge overpotential to ~0.2 V. The cathode utilizes atomic layer deposition of palladium nanoparticles on a carbon surface with an alumina coating for passivation of carbon defect sites. The low charge potential is enabled by the combination of palladium nanoparticles attached to the carbon cathode surface, a nanocrystalline form of lithium peroxide with grain boundaries, and the alumina coating preventing electrolyte decomposition on carbon. High-resolution transmission electron microscopy provides evidence for the nanocrystalline form of lithium peroxide. The new cathode material architecture provides the basis for future development of lithium-oxygen cathode materials that can be used to improve the efficiency and to extend cycle life.

A nanostructured cathode architecture for low charge overpotential in lithium-oxygen batteries.

A molecular-level understanding of the reactions that occur at the lithium-metal anode/electrolyte interphase is essential to improve the performance of Li-O(2) batteries. Experimental and computational techniques are applied to explore the reactivity of tri(ethylene glycol)-substituted trimethylsilane (1NM3), a siloxane-based ether electrolyte, at the lithium-metal anode. In situ/ex situ X-ray diffraction and Fourier-transform infrared spectroscopy studies provide evidence of the formation of lithium hydroxide and lithium carbonates at the anode upon gradual degradation of the metallic lithium anode and the solvent molecules in the presence of oxygen. Density functional calculations performed to obtain a mechanistic understanding of the reductive decomposition of 1NM3 indicate that the decomposition does not require any apparent barrier to produce lithium hydroxide and lithium carbonates when the reduced 1NM3 solvent molecules interact with the oxygen crossing over from the cathode. This study indicates that degradation may be more significant in the case of the 1NM3 solvent, compared to linear ethers such as tetraglyme or dioxalone, because of its relatively high electron affinity. Also, both protection of the lithium metal and prevention of oxygen crossover to the anode are essential for minimizing electrolyte and anode decomposition.

Molecular-level insights into the reactivity of siloxane-based electrolytes at a lithium-metal anode.

Lithium-oxygen batteries have the potential needed for long-range electric vehicles, but the charge and discharge chemistries are complex and not well understood. The active sites on cathode surfaces and their role in electrochemical reactions in aprotic lithium-oxygen cells are difficult to ascertain because the exact nature of the sites is unknown. Here we report the deposition of subnanometre silver clusters of exact size and number of atoms on passivated carbon to study the discharge process in lithium-oxygen cells. The results reveal dramatically different morphologies of the electrochemically grown lithium peroxide dependent on the size of the clusters. This dependence is found to be due to the influence of the cluster size on the formation mechanism, which also affects the charge process. The results of this study suggest that precise control of subnanometre surface structure on cathodes can be used as a means to improve the performance of lithium-oxygen cells.

Effect of the size-selective silver clusters on lithium peroxide morphology in lithium-oxygen batteries.

This letter reports on the investigation of a binder-free cathode material to be used in rechargeable aluminum batteries. This cathode is synthesized by directly depositing V2O5 on a Ni foam current collector. Rechargeable aluminum coin cells fabricated using the as-synthesized binder-free cathode delivered an initial discharge capacity of 239 mAh/g, which is much higher than that of batteries fabricated using a cathode composed of V2O5 nanowires and binder. An obvious discharge voltage plateau appeared at 0.6 V in the discharge curves of the Ni-V2O5 cathode, which is slightly higher than that of the V2O5 nanowire cathodes with common binders. This improvement is attributed to reduced electrochemical polarization.

Binder-free V2O5 cathode for greener rechargeable aluminum battery.

Uniformly dispersed Pd nanoparticles on ZnO-passivated porous carbon were synthesized via an atomic layer deposition (ALD) technique, which was tested as a cathode material in a rechargeable Li-O2 battery, showing a highly active catalytic effect toward the electrochemical reactions-in particular, the oxygen evolution reaction. Transmission electron microscopy (TEM) showed discrete crystalline nanoparticles decorating the surface of the ZnO-passivated porous carbon support in which the size could be controlled in the range of 3-6 nm, depending on the number of Pd ALD cycles performed. X-ray absorption spectroscopy (XAS) at the Pd K-edge revealed that the carbon-supported Pd existed in a mixed phase of metallic palladium and palladium oxide. The ZnO-passivated layer effectively blocks the defect sites on the carbon surface, minimizing the electrolyte decomposition. Our results suggest that ALD is a promising technique for tailoring the surface composition and structure of nanoporous supports for Li-O2 batteries.

Pd nanoparticles on ZnO-passivated porous carbon by atomic layer deposition: an effective electrochemical catalyst for Li-O2 battery.

Among many challenges present in Li-air batteries, one of the main reasons of low efficiency is the high charge overpotential due to the slow oxygen evolution reaction (OER). Here, we present systematic evaluation of Pt, Pd, and Ru nanoparticles supported on rGO as OER electrocatalysts in Li-air cell cathodes with LiCF3SO3-tetra(ethylene glycol) dimethyl ether (TEGDME) salt-electrolyte system. All of the noble metals explored could lower the charge overpotentials, and among them, Ru-rGO hybrids exhibited the most stable cycling performance and the lowest charge overpotentials. Role of Ru nanoparticles in boosting oxidation kinetics of the discharge products were investigated. Apparent behavior of Ru nanoparticles was different from the conventional electrocatalysts that lower activation barrier through electron transfer, because the major contribution of Ru nanoparticles in lowering charge overpotential is to control the nature of the discharge products. Ru nanoparticles facilitated thin film-like or nanoparticulate Li2O2 formation during oxygen reduction reaction (ORR), which decomposes at lower potentials during charge, although the conventional role as electrocatalysts during OER cannot be ruled out. Pt-and Pd-rGO hybrids showed fluctuating potential profiles during the cycling. Although Pt- and Pd-rGO decomposed the electrolyte after electrochemical cycling, no electrolyte instability was observed with Ru-rGO hybrids. This study provides the possibility of screening selective electrocatalysts for Li-air cells while maintaining electrolyte stability.

Study on the Catalytic Activity of Noble Metal Nanoparticles on Reduced Graphene Oxide for Oxygen Evolution Reactions in Lithium-Air Batteries.

The oxygen evolution reaction (OER) plays a critical role in multiple energy conversion and storage applications. However, its sluggish kinetics usually results in large voltage polarization and unnecessary energy loss. Therefore, designing efficient catalysts that could facilitate this process has become an emerging topic. Here, we present a unique Pt-Cu core-shell nanostructure for catalyzing the nonaqueous OER. The catalysts were systematically investigated with comprehensive spectroscopic techniques, and applied in nonaqueous Li-O2 electrochemical cells, which exhibited dramatically reduced charging overpotential (<0.2 V). The superior performance is explained by the robust Cu(I) surface sites stabilized by the Pt core in the nanostructure. The insights into the catalytic mechanism of the unique Pt-Cu core-shell nanostructure gained in this work are expected to serve as a guide for future design of other nanostructured bimetallic OER catalysts.

Insight into the Catalytic Mechanism of Bimetallic Platinum-Copper Core-Shell Nanostructures for Nonaqueous Oxygen Evolution Reactions.

Batteries based on sodium superoxide and on potassium superoxide have recently been reported. However, there have been no reports of a battery based on lithium superoxide (LiO2), despite much research into the lithium-oxygen (Li-O2) battery because of its potential high energy density. Several studies of Li-O2 batteries have found evidence of LiO2 being formed as one component of the discharge product along with lithium peroxide (Li2O2). In addition, theoretical calculations have indicated that some forms of LiO2 may have a long lifetime. These studies also suggest that it might be possible to form LiO2 alone for use in a battery. However, solid LiO2 has been difficult to synthesize in pure form because it is thermodynamically unstable with respect to disproportionation, giving Li2O2 (refs 19, 20). Here we show that crystalline LiO2 can be stabilized in a Li-O2 battery by using a suitable graphene-based cathode. Various characterization techniques reveal no evidence for the presence of Li2O2. A novel templating growth mechanism involving the use of iridium nanoparticles on the cathode surface may be responsible for the growth of crystalline LiO2. Our results demonstrate that the LiO2 formed in the Li-O2 battery is stable enough for the battery to be repeatedly charged and discharged with a very low charge potential (about 3.2 volts). We anticipate that this discovery will lead to methods of synthesizing and stabilizing LiO2, which could open the way to high-energy-density batteries based on LiO2 as well as to other possible uses of this compound, such as oxygen storage.

A lithium-oxygen battery based on lithium superoxide.

The side reactions between the electrode materials and the nonaqueous electrolytes have been the major contributor to the degradation of electrochemical performance of lithium-ion batteries. A home-built high-precision leakage current measuring system was deployed to investigate the reaction kinetics between the delithiated LiNi(0.6)Mn(0.2)Co(0.2)O2 and a conventional nonaqueous electrolyte. It was found that the rate of parasitic reaction had strong dependence on the upper cutoff potential of the cathode material. The kinetic data also indicated a change of reaction mode at about 4.5 V vs Li(+)/Li.

Xiangyi Luo

Chemistry Sciences and Engineering Division

Argonne National Laboratory

Protocol of Electrochemical Test and Characterization of Aprotic Li-O₂ Battery

Xiangyi Luo

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Chemistry Sciences and Engineering Division

Argonne National Laboratory

Protocol of Electrochemical Test and Characterization of Aprotic Li-O2 Battery

Chemistry Sciences and Engineering Division

Protocol of Electrochemical Test and Characterization of Aprotic Li-O₂ Battery