Samuel L. Pfaff is a Professor in the Gene Expression Laboratories at The Salk Institute for biological Studies and an Investigator in the Howard Hughes Medical Institute. This work was supported by the Christopher and Dana Reeve Foundation. Joe Belcovson, Kent Schnoeker and Mike Sullivan in Multimedia Resources at the Salk Institute provided assistance with photography and editing.

Electrophysiological recordings of isolated spinal cords can reveal genetic and developmental changes to neural circuitry 1. We previously demonstrated a method to dissect neonatal mouse spinal cords 2. Here we present a method to prepare suction electrodes useful in recording fictive locomotion in isolated spinal cords 3.
The tip of a plastic tubing electrode can be drawn to a very fine tip by hand using a low-temperature alcohol lamp 3-5. The plastic tubing (PE90, Clay Adams IntramedicTM) is held over the flame to soften the tubing into a malleable form. As the tubing begins to melt and becomes more translucent it is removed from the heat source and the ends are gently pulled apart. The timing of removing the tube from the flame is important to insure the plastic does not collapse or split while being drawn. The thin portion of the tubing is cut with a razor blade according to the desired internal diameter, as dictated by the age of the specimen or the segmental level of the cord. For ease of placing an o-ring on the tubing, a 45&deg; cut is made at the thick end of the tubing with a razor blade. A ferrule and o-ring are installed on the thick end to attach the electrode tip to the barrel of the electrode.
To allow for specifically sized electrodes and avoid the difficulties of hand-pulling electrode tips, electrodes can be constructed using small tubing inserted into a thicker tubing (PE90). The lengths of the tubing are specific to the requirements of the recording setup and are variable. We present the measurements used in our experiments 1-3,5. A 1cm length of PTFE fine tubing (Zeus, Small Parts) and a 10cm length of PE90 tubing are cut with a razor blade. The ends of the small tubing should be examined to be sure they are not crushed or closed. They can be opened using an insect pin (Fine Science Tools). A drop of adhesive (JB Weld) is placed onto the midpoint of the PTFE tubing. The PTFE tubing and adhesive are drawn into the PE90 tubing using mouth suction on the PE90 tubing. A 45&deg; cut is made at the thick end of the tubing and a ferrule and o-ring are attached, as previous.
The ferrule and BNC connector are unscrewed from a commercial suction electrode. The BNC connector is soaked in xylene for one hour to remove the wax seal. The connector is then rinsed in water and dried.
A lower angled side port must be made on the side of the barrel. A metal rod is heated using a Bunsen burner and pressed into the existing hole on the side of the barrel at a low angle. A 15cm length of 0.010 inch silver wire (A-M Systems) is cut and soaked in bleach for fifteen minutes. This is done to create a silver chloride coating that aids in signal conduction 6. The wire is rinsed with water, dried, and then soldered onto the BNC connector. The BNC connector and silver wire are inserted into the suction electrode barrel with enough room for the BNC connector to remain to the side of the barrel. Suction tubing is inserted into the side port 2-3cm. Silicone sealant is injected into the barrel approximately 2-3cm. The BNC connector is threaded into the barrel of the electrode pushing the sealant forward.
The tip of the electrode is now threaded into the front end of the electrode. Shrink tubing can also be added to reinforce the suction line from the side port.
Electrodes are mounted on micromanipulators that are attached to magnetic stands, and placed near the recording dish. BNC coaxial cables are attached to a headstage that is wired to an amplifier. The amplifier is connected to an adaptor (Polyview) that is connected to a analog to digital card (National Instruments) in a PC computer with data acquisition software (Polyview).
When recording electrophysiological data, it is necessary to eliminate all outside interference. The recording dish, amplifier, and head stage are placed on an air table within a Faraday cage to prevent electrical and mechanical interference, respectively.
Representative Results:
<img src="/files/ftp_upload/2580/2580fig1.jpg" alt="Figure 1" /> 
Figure 1. A commercially available suction electrode can be modified by adding a heavier gauge silver wire and a plastic tip that is hand drawn on an alcohol lamp, or constructed with commercially available plastic tubing of specific sizes. In addition, the paraffin sealant is replaced with more durable silicone caulk sealant.
<img src="/files/ftp_upload/2580/2580fig2.jpg" alt="Figure 2" /> 
Figure 2. A schematic of the suction electrode in relation to the air table (for mechanical isolation), Faraday cage (electrical isolation), amplifier and computer. It should be noted that there is a ground referenced to the recording dish and a second ground that is referenced to the air table and Faraday cage.

<ol>
	<li>Gallarda, B. W., Sharpee, T. O., Pfaff, S. L., Alaynick, W. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Defining+rhythmic+locomotor+burst+patterns+using+a+continuous+wavelet+transform.">Defining rhythmic locomotor burst patterns using a continuous wavelet transform.</a> Ann N Y Acad Sci. 1198, 133-139 (2010).</li><li>Meyer, A., Gallarda, B. W., Pfaff, S., Alaynick, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Spinal+cord+electrophysiology.">Spinal cord electrophysiology.</a> J Vis Exp. , (2010).</li><li>Gallarda, B. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Segregation+of+axial+motor+and+sensory+pathways+via+heterotypic+trans-axonal+signaling.">Segregation of axial motor and sensory pathways via heterotypic trans-axonal signaling.</a> Science. 320, 233-236 (2008).</li><li>Landmesser, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+development+of+motor+projection+patterns+in+the+chick+hind+limb.">The development of motor projection patterns in the chick hind limb.</a> J Physiol. 284, 391-414 (1978).</li><li>Myers, C. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cholinergic+input+is+required+during+embryonic+development+to+mediate+proper+assembly+of+spinal+locomotor+circuits.">Cholinergic input is required during embryonic development to mediate proper assembly of spinal locomotor circuits.</a> Neuron. 46, 37-49 (2005).</li><li>Chanin, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+determination+of+chloride+by+use+of+the+silver-silver+chloride+electrode.">The determination of chloride by use of the silver-silver chloride electrode.</a> Science. 119, 323-324 (1954).</li><li>Goulding, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Circuits+controlling+vertebrate+locomotion:+moving+in+a+new+direction.">Circuits controlling vertebrate locomotion: moving in a new direction.</a> Nat Rev Neurosci. 10, 507-518 (2009).</li></ol>

No conflicts of interest declared.

Nervous system development can be studied using isolated rodent spinal cords. In the presence of neurotransmitters, fictive locomotion can be generated from the spinal cord in the form of patterned electrical activity 1,3. These rhythmic bursts are produced at 0.2 to 0.5 Hz and are patterned in left-right and flexor-extensor alternations. At different developmental stages, the robustness and patterns of this activity varies 1. Genetic mutations can also disturb the patterning of this activity 3...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>PTFE Sub Lite Wall Tubing (Small tubing)</td>
<td>&nbsp;</td>
<td>Zeus</td>
<td>36AWG</td>
<td>0.005&#x201D;ID x 0.003&#x201D; Wall (Small Parts) Also available in 0.003&#x201D; to 0.006&#x201D;</td>
</tr>
<tr>
<td>Large tubing (0.86mm (0.34&#x201D;))</td>
<td>&nbsp;</td>
<td>Clay Adams Brand Intramedic Becton Dickinson and Company</td>
<td>427420</td>
<td>0.86mm (0.34&#x201D;) O.D. 1.27mm (.050&#x201D;)</td>
</tr>
<tr>
<td>Electrode Barrel</td>
<td>&nbsp;</td>
<td>A-M Systems</td>
<td>573000</td>
<td>&nbsp;</td>
<tr>
<td>Adhesive</td>
<td>&nbsp;</td>
<td>JB Weld</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Adhesive: Silicone caulk</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Solder and soldering iron</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Bleach</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Xylene</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Silver wire: 0.010&#x201D;</td>
<td>&nbsp;</td>
<td>A-M Systems</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Insect pins: Austerlitz 0.1mm</td>
<td>&nbsp;</td>
<td>Fine Science Tools</td>
<td>26002-10</td>
<td>&nbsp;</td>
<tr>
<td>Magnetic Stand</td>
<td>&nbsp;</td>
<td>Narishige</td>
<td>GJ-8</td>
<td>&nbsp;</td>
<tr>
<td>Micromanipulator</td>
<td>&nbsp;</td>
<td>Narishige</td>
<td>MN 151</td>
<td>&nbsp;</td>
<tr>
<td>Miniboard (Headstage)</td>
<td>&nbsp;</td>
<td>Grass Industries</td>
<td>F-15EB/B1</td>
<td>&nbsp;</td>
<tr>
<td>Polyview Adaptor Unit</td>
<td>&nbsp;</td>
<td>Grass Industries</td>
<td>PVA 8</td>
<td>&nbsp;</td>
<tr>
<td>Bipolar Portable Physiodata Amplifier System</td>
<td>&nbsp;</td>
<td>Grass Industries</td>
<td>15LT</td>
<td>&nbsp;</td>
<tr>
<td>ANALOG TO DIGITAL CARD</td>
<td>&nbsp;</td>
<td>National Instruments</td>
<td>6035E</td>
<td>&nbsp;</td>
<tr>
<td>Air Table; Vibraplane</td>
<td>&nbsp;</td>
<td>Kinetic Systems</td>
<td>&nbsp;</td>
<td>&nbsp;</td>		</tbody>
		</table>
		</div>

spinal cord electrophysiology ii: extracellular suction electrode fabrication

Development of neural circuitries and locomotion can be studied using neonatal rodent spinal cord central pattern generator (CPG) behavior. We demonstrate a method to fabricate suction electrodes that are used to examine CPG activity, or fictive locomotion, in dissected rodent spinal cords. The rodent spinal cords are placed in artificial cerebrospinal fluid and the ventral roots are drawn into the suction electrode. The electrode is constructed by modifying a commercially available suction electrode. A heavier silver wire is used instead of the standard wire given by the commercially available electrode. The glass tip on the commercial electrode is replaced with a plastic tip for increased durability. We prepare hand drawn electrodes and electrodes made from specific sizes of tubing, allowing consistency and reproducibility. Data is collected using an amplifier and neurogram acquisition software. Recordings are performed on an air table within a Faraday cage to prevent mechanical and electrical interference, respectively.

Watch this Scientific Journal Video about Spinal Cord Electrophysiology II: Extracellular Suction Electrode Fabrication at JoVE.com

Spinal Cord Electrophysiology II: Extracellular Suction Electrode Fabrication

A demonstration of the fabrication and use of an extracellular suction electrode used to measure electrophysiological recordings of neonatal rodent spinal cords in vitro

Development of neural circuitries and locomotion can be studied using neonatal rodent spinal cord central pattern generator (CPG) behavior. We demonstrate ...

spinal-cord-electrophysiology-ii-extracellular-suction-electrode

Research

JoVE Journal

Neuroscience

15.0K Views.  The Salk Institute for Biological Studies. A demonstration of the fabrication and use of an extracellular suction electrode used to measure electrophysiological recordings of neonatal rodent spinal cords in vitro

Video: Spinal Cord Electrophysiology II: Extracellular Suction Electrode Fabrication

Chicken Embryo Spinal Cord Slice Culture Protocol

Slice cultures can facilitate the manipulation of embryo development both pharmacologically and through gene manipulations. In this reduced system, potential lethal side effects due to systemic drug applications can be overcome. However, culture conditions must ensure that normal development proceeds within the reduced environment of the slice. We have focused on the development of the spinal cord, particularly that of spinal motor neurons. We systematically varied culture conditions of chicken embryo slices from the point at which most spinal motor neurons had been born. We assayed the number and type of motor neurons that survived during the culture period and the position of those motor neurons compared to that in vivo. We found that serum type and neurotrophic factors were required during the culture period and were able to keep motor neurons alive for at least 24 hr and allow those motor neurons to migrate to appropriate positions in the spinal cord. We present these culture conditions and the methodology of preparing the embryo slice cultures using eviscerated chicken embryos embedded in agarose and sliced using a vibratome.

Slice cultures facilitate the manipulation of embryo development by gene and pharmacological perturbations. However, culture conditions must ensure that normal development can proceed within the reduced environment of the slice. We illustrate a protocol that facilitates normal spinal cord development to proceed for at least 24 hr.

Slice cultures can facilitate the manipulation of  embryo development both pharmacologically and through gene manipulations. In  this reduced system, ...

Spinal Cord Transection in the Larval Zebrafish

Mammals fail in sensory and motor recovery following spinal cord injury due to lack of axonal regrowth below the level of injury as well as an inability to reinitiate spinal neurogenesis. However, some anamniotes including the zebrafish Danio rerio exhibit both sensory and functional recovery even after complete transection of the spinal cord. The adult zebrafish is an established model organism for studying regeneration following spinal cord injury, with sensory and motor recovery by 6&#160;weeks post-injury. To take advantage of in vivo analysis of the regenerative process available in the transparent larval zebrafish as well as genetic tools not accessible in the adult, we use the larval zebrafish to study regeneration after spinal cord transection. Here we demonstrate a method for reproducibly and verifiably transecting the larval spinal cord. After transection, our data shows sensory recovery beginning at 2&#160;days post-injury (dpi), with the C-bend movement detectable by 3 dpi and resumption of free swimming by 5 dpi. Thus we propose the larval zebrafish as a companion tool to the adult zebrafish for the study of recovery after spinal cord injury.

After spinal transection, adult zebrafish have functional recovery by six weeks post-injury. To take advantage of larval transparency and faster recovery, we present a method for transecting the larval spinal cord. After transection, we observe sensory recovery beginning at 2&#160;days post-injury, and C-bend movement by 3 days post-injury.

Mammals fail in sensory and motor recovery following spinal cord injury due to lack of axonal regrowth below the level of injury as well as an inability ...

An Ex Vivo Laser-induced Spinal Cord Injury Model to Assess Mechanisms of Axonal Degeneration in Real-time

Injured CNS axons fail to regenerate and often retract away from the injury site. Axons spared from the initial injury may later undergo secondary axonal degeneration. Lack of growth cone formation, regeneration, and loss of additional myelinated axonal projections within the spinal cord greatly limits neurological recovery following injury. To assess how central myelinated axons of the spinal cord respond to injury, we developed an ex vivo living spinal cord model utilizing transgenic mice that express yellow fluorescent protein in axons and a focal and highly reproducible laser-induced spinal cord injury to document the fate of axons and myelin (lipophilic fluorescent dye Nile Red) over time using two-photon excitation time-lapse microscopy. Dynamic processes such as acute axonal injury, axonal retraction, and myelin degeneration are best studied in real-time. However, the non-focal nature of contusion-based injuries and movement artifacts encountered during in vivo spinal cord imaging make differentiating primary and secondary axonal injury responses using high resolution microscopy challenging. The ex vivo spinal cord model described here mimics several aspects of clinically relevant contusion/compression-induced axonal pathologies including axonal swelling, spheroid formation, axonal transection, and peri-axonal swelling providing a useful model to study these dynamic processes in real-time. Major advantages of this model are excellent spatiotemporal resolution that allows differentiation between the primary insult that directly injures axons and secondary injury mechanisms; controlled infusion of reagents directly to the perfusate bathing the cord; precise alterations of the environmental milieu (e.g., calcium, sodium ions, known contributors to axonal injury, but near impossible to manipulate in vivo); and murine models also offer an advantage as they provide an opportunity to visualize and manipulate genetically identified cell populations and subcellular structures. Here, we describe how to isolate and image the living spinal cord from mice to capture dynamics of acute axonal injury.

An Ex Vivo Laser-induced Spinal Cord Injury Model to Assess Mechanisms of Axonal Degeneration in Real-time

We present a protocol utilizing two-photon excitation time-lapse microscopy to simultaneously visualize the dynamics of axon and myelin injuries in real time. This proposed protocol permits studies of both intrinsic and extrinsic factors which can influence central myelinated axon fate after injury and contribute to permanent clinical disability.

Injured CNS axons fail to regenerate and often retract away from the injury site. Axons spared from the initial injury may later undergo secondary axonal ...

Electrophysiology on Isolated Brainstem-spinal Cord Preparations from Newborn Rodents Allows Neural Respiratory Network Output Recording

While it is well known that the central respiratory drive is located in the brainstem, several aspects of its basic function, development, and response to stimuli remain to be fully understood. To overcome the difficulty of accessing the brainstem in the whole animal, isolation of the brainstem and part of the spinal cord is performed. This preparation is maintained in artificial cerebro-spinal fluid where gases, concentrations, and temperature are controlled and monitored. The output signal from the respiratory network is recorded by a suction electrode placed on the fourth ventral root. In this manner, stimuli can be directly applied onto the brainstem, and the effect can be recorded directly. The signal recorded is linked to the inspiratory signal sent to the diaphragm via the phrenic nerve, and can be described as bursts (around 8 bursts per minute). Analysis of these bursts (frequency, amplitude, length, and area under the curve) allows precise characterization of the stimulus effect on the respiratory network. The main limitation of this method is the viability of the preparation beyond the early post-natal stages. Thus, this method greatly focuses on the study of the whole network without the peripheral inputs in the newborn rat.

The central respiratory drive is located in the brainstem. Spontaneous respiratory motor output from an isolated brainstem-spinal cord is recorded by placing an electrode on the fourth ventral root. This experimental approach is valuable for pharmacological investigations or the assessment of respiratory challenges and genetic manipulations on rhythmic motor behavior.

While it is well known that the central respiratory drive is located in the brainstem, several aspects of its basic function, development, and response to ...

Investigating Functional Regeneration in Organotypic Spinal Cord Co-cultures Grown on Multi-electrode Arrays

Adult higher vertebrates have a limited potential to recover from spinal cord injury. Recently, evidence emerged that propriospinal connections are a promising target for intervention to improve functional regeneration. So far, no in vitro model exists that grants the possibility to examine functional recovery of propriospinal fibers. Therefore, a representative model that is based on two organotypic spinal cord sections of embryonic rat, cultured next to each other on multi-electrode arrays (MEAs) was developed. These slices grow and, within a few days in vitro, fuse along the sides facing each other. The design of the used MEAs permits the performance of lesions with a scalpel blade through this fusion site without inflicting damage on the MEAs. The slices show spontaneous activity, usually organized in network activity bursts, and spatial and temporal activity parameters such as the location of burst origins, speed and direction of their propagation and latencies between bursts can be characterized. Using these features, it is also possible to assess functional connection of the slices by calculating the amount of synchronized bursts between the two sides. Furthermore, the slices can be morphologically analyzed by performing immunohistochemical stainings after the recordings. 
Several advantages of the used techniques are combined in this model: the slices largely preserve the original tissue architecture with intact local synaptic circuitry, the tissue is easily and repeatedly accessible and neuronal activity can be detected simultaneously and non-invasively in a large number of spots at high temporal resolution. These features allow the investigation of functional regeneration of intraspinal connections in isolation in vitro in a sophisticated and efficient way.

Here we present a protocol that is based on spinal cord slices cultured on multi-electrode arrays to study functional regeneration of propriospinal connections in vitro.

Adult higher vertebrates have a limited potential to recover from spinal cord injury. Recently, evidence emerged that propriospinal connections are a ...

Spiral Ganglion Neuron Explant Culture and Electrophysiology on Multi Electrode Arrays

Spiral ganglion neurons (SGNs) participate in the physiological process of hearing by relaying signals from sensory hair cells to the cochlear nucleus in the brain stem. Loss of hair cells is a major cause of sensory hearing loss. Prosthetic devices such as cochlear implants function by bypassing lost hair cells and directly stimulating SGNs electrically, allowing for restoration of hearing in deaf patients. The performance of these devices depends on the functionality of SGNs, the implantation procedure and on the distance between the electrodes and the auditory neurons. 
We hypothesized, that reducing the distance between the SGNs and the electrode array of the implant would allow for improved stimulation and frequency resolution, with the best results in a gapless position. Currently we lack in vitro culture systems to study, modify and optimize the interaction between auditory neurons and electrode arrays and characterize their electrophysiological response. To address these issues, we developed an in vitro bioassay using SGN cultures on a planar multi electrode array (MEA). With this method we were able to perform extracellular recording of the basal and electrically induced activity of a population of spiral ganglion neurons. We were also able to optimize stimulation protocols and analyze the response to electrical stimuli as a function of the electrode distance. This platform could also be used to optimize electrode features such as surface coatings.

We present a protocol to culture primary murine spiral ganglion neuron explants on multi electrode arrays to study neuronal response profiles and optimize stimulation parameters. Such studies aim to improve the neuron-electrode interface of cochlear implants to benefit hearing in patients as well as the energy consumption of the device.

Spiral ganglion neurons (SGNs) participate in the physiological process of hearing by relaying signals from sensory hair cells to the cochlear nucleus in ...

Imaging Neural Activity in the Primary Somatosensory Cortex Using Thy1-GCaMP6s Transgenic Mice

The mammalian brain exhibits marked symmetry across the sagittal plane. However, detailed description of neural dynamics in symmetric brain regions in adult mammalian animals remains elusive. In this study, we describe an experimental procedure for measuring calcium dynamics through dual optical windows above bilateral primary somatosensory corticies (S1) in Thy1-GCaMP6s transgenic mice using 2-photon (2P) microscopy. This method enables recordings and quantifications of neural activity in bilateral mouse brain regions one at a time in the same experiment for a prolonged period in vivo. Key aspects of this method, which can be completed within an hour, include minimally invasive surgery procedures for creating dual optical windows, and the use of 2P imaging. Although we only demonstrate the technique in the S1 area, the method can be applied to other regions of the living brain facilitating the elucidation of structural and functional complexities of brain neural networks.

Imaging Neural Activity in the Primary Somatosensory Cortex Using Thy1-GCaMP6s Transgenic Mice

We describe an experimental procedure for measuring neuronal activity through dual optical windows above bilateral primary somatosensory corticies (S1) in Thy1-GCaMP6s transgenic mice using 2-photon (2P) microscopy in vivo.

The mammalian brain exhibits marked symmetry across the sagittal plane. However, detailed description of neural dynamics in symmetric brain regions in ...

Activity-based Training on a Treadmill with Spinal Cord Injured Wistar Rats

Spinal cord injury (SCI) results in lasting deficits that include both mobility and a multitude of autonomic-related dysfunctions. Locomotor training (LT) on a treadmill is widely used as a rehabilitation tool in the SCI population with many benefits and improvements to daily life. We utilize this method of activity-based task-specific training (ABT) in rodents after SCI to both elucidate the mechanisms behind such improvements and to enhance and improve upon existing clinical rehabilitation protocols. Our current goal is to determine the mechanisms underlying ABT-induced improvements in urinary, bowel, and sexual function in SCI rats after a moderate to severe level of contusion. After securing each individual animal in a custom-made adjustable vest, they are secured to a versatile body weight support mechanism, lowered to a modified three-lane treadmill and assisted in step-training for 58 minutes, once a day for 10 weeks. This setup allows for the training of both quadrupedal and forelimb-only animals, alongside two different non-trained groups. Quadrupedal-trained animals with body weight support are aided by a technician present to assist in stepping with proper hind limb placement as necessary, while forelimb-only trained animals are raised at the caudal end to ensure no hind limb contact with the treadmill and no weight-bearing. One non-trained SCI group of animals is placed in a harness and rests next to the treadmill, while the other control SCI group remains in its home cage in the training room nearby. This paradigm allows for the training of multiple SCI animals at once, thus making it more time-efficient in addition to ensuring that our pre-clinical animal model mimics the clinical representation as close as possible, particularly with respect to the body weight support with manual assistance.

This protocol demonstrates our model of activity-based locomotor treadmill training for rats with spinal cord injury (SCI). Included is both quadrupedal and forelimb-only groups, in addition to two distinct types of non-trained control groups. Investigators are able to assess training effects on SCI rats using this protocol.

Spinal cord injury (SCI) results in lasting deficits that include both mobility and a multitude of autonomic-related dysfunctions. Locomotor training (LT) ...

Intra-Arterial Delivery of Neural Stem Cells to the Rat and Mouse Brain: Application to Cerebral Ischemia

Neural stem cell (NSC) therapy is an emerging innovative treatment for stroke, traumatic brain injury and neurodegenerative disorders. As compared to intracranial delivery, intra-arterial administration of NSCs is less invasive and produces a more diffuse distribution of NSCs within the brain parenchyma. Further, intra-arterial delivery allows the first-pass effect in the brain circulation, lessening the potential for trapping of cells in peripheral organs, such as liver and spleen, a complication associated with peripheral injections. Here, we detail the methodology, in both mice and rats, for delivery of NSCs through the common carotid artery (mouse) or external carotid artery (rat) to the ipsilateral hemisphere after an ischemic stroke. Using GFP-labeled NSCs, we illustrate the widespread distribution achieved throughout the rodent ipsilateral hemisphere at 1 d, 1 week and 4 weeks after postischemic delivery, with a higher density in or near the ischemic injury site. In addition to long-term survival, we show evidence of differentiation of GFP-labeled cells at 4 weeks. The intra-arterial delivery approach described here for NSCs can also be used for administration of therapeutic compounds, and thus has broad applicability to varied CNS injury and disease models across multiple species.

A method for delivering neural stem cells, adaptable for injecting solutions or suspensions, through the common carotid artery (mouse) or external carotid artery (rat) after ischemic stroke is reported. Injected cells are distributed broadly throughout the brain parenchyma and can be detected up to 30 d after delivery.

Neural stem cell (NSC) therapy is an emerging innovative treatment for stroke, traumatic brain injury and neurodegenerative disorders. As compared to ...

Uptake of Fluorescent Labeled Small Extracellular Vesicles In Vitro and in Spinal Cord

Small extracellular vesicles (sEVs) are 50-150 nm vesicles secreted by all cells and present in bodily fluids. sEVs transfer biomolecules such as RNA, proteins, and lipids from donor to acceptor cells, making them key signaling mediators between cells. In the central nervous system (CNS), sEVs can mediate intercellular signaling, including neuroimmune interactions. sEV functions can be studied by tracking the uptake of labeled sEVs in recipient cells both in vitro and in vivo. This paper describes the labeling of sEVs from the conditioned media of RAW 264.7 macrophage cells using a PKH membrane dye. It shows the uptake of different concentrations of labeled sEVs at multiple time points by Neuro-2a cells and primary astrocytes in vitro. Also shown is the uptake of sEVs delivered intrathecally in mouse spinal cord neurons, astrocytes, and microglia visualized by confocal microscopy. The representative results demonstrate time-dependent variation in the uptake of sEVs by different cells, which can help confirm successful sEVs delivery into the spinal cord.

Uptake of Fluorescent Labeled Small Extracellular Vesicles In Vitro and in Spinal Cord

We describe a protocol to label macrophage-derived small extracellular vesicles with PKH dyes and observe their uptake in vitro and in the spinal cord after intrathecal delivery.

Small extracellular vesicles (sEVs) are 50-150 nm vesicles secreted by all cells and present in bodily fluids. sEVs transfer biomolecules such as RNA, ...