artificial-lung-device-priming-for-situ-fiber-bundle-surface

Artificial Lung Device Priming for In Situ Fiber Bundle Surface Grafting

Although the high surface area-to-volume ratio of the artificial lung fiber bundle enhances gas exchange, the large surface area, dense arrangement, and ...

University of New Haven

The large, densely packed artificial surface area of artificial lungs results in rapid clotting and device failure. Surface generated nitric oxide (NO) can be used to reduce platelet activation and coagulation on gas exchange fibers, while not inducing patient bleeding due to its short half-life in blood. To generate NO, artificial lungs can be manufactured with PDMS hollow fibers embedded with copper nanoparticles (Cu NP) and supplied with an infusion of the NO donor S-nitroso-N-acetyl-penicillamine (SNAP). The SNAP reacts with Cu NP to generate NO. This study investigates clot formation and gas exchange performance of artificial lungs with either NO-generating Cu-PDMS or standard polymethylpentene (PMP) fibers. One miniature artificial lung (MAL) made with 10 wt% Cu-PDMS hollow fibers and one PMP control MAL were attached to sheep in parallel in a veno-venous extracorporeal membrane oxygenation circuit (n = 8). Blood flow through each device was set at 300 mL/min, and each device received a SNAP infusion of 0.12 μmol/min. The ACT was between 110 and 180 s in all cases. Blood flow resistance was calculated as a measure of clot formation on the fiber bundle. Gas exchange experiments comparing the two groups were conducted every 24 h at blood flow rates of 300 and 600 mL/min. Devices were removed once the resistance reached 3x baseline (failure) or following 72 h. All devices were imaged using scanning electron microscopy (SEM) at the inlet, outlet, and middle of the fiber bundle. The Cu-PDMS NO generating MALs had a significantly smaller increase in resistance compared to the control devices. Resistance rose from 26 ± 8 and 23 ± 5 in the control and Cu-PDMS devices, respectively, to 35 ± 8 mmHg/(mL/min) and 72 ± 23 mmHg/(mL/min) at the end of each experiment. The resistance and SEM imaging of fiber surfaces demonstrate lower clot formation on Cu-PDMS fibers. Although not statistically significant, oxygen transfer for the Cu-PDMS MALs was 13.3% less than the control at 600 mL/min blood flow rate. Future in vivo studies with larger Cu-PDMS devices are needed to define gas exchange capabilities and anticoagulant activity over a long-term study at clinically relevant ACTs. STATEMENT OF SIGNIFICANCE: In artificial lungs, the large, densely-packed blood contacting surface area of the hollow fiber bundle is critical for gas exchange but also creates rapid, surface-generated clot requiring significant anticoagulation. Monitoring of anticoagulation, thrombosis, and resultant complications has kept permanent respiratory support from becoming a clinical reality. In this study, we use a hollow fiber material that generates nitric oxide (NO) to prevent platelet activation at the blood contacting surface. This material is tested in vivo in a miniature artificial lung and compared against the clinical standard. Results indicated significantly reduced clot formation. Surface-focused anticoagulation like this should reduce complication rates and allow for permanent respiratory support by extending the functional lifespan of artificial lungs and can further be applied to other medical devices.

72-Hour in vivo evaluation of nitric oxide generating artificial lung gas exchange fibers in sheep.

The aim of the current study was to investigate the effects of mineral trioxide aggregate (MTA) on the proliferation and differentiation of human adipose-derived mesenchymal stem cells (Ad-MSCs) as a surrogate cell source in futuristic stem-cell-based endodontic therapies. Human Ad-MSCs and mesenchymal stem cells derived from bone marrow (BM-MSCs) were isolated from liposuction waste adipose tissue and femur, respectively, and the effects of MTA-conditioned media on their viability, mineralization potential, and osteo/odontogenic differentiation capacity were subsequently evaluated. Alkaline phosphatase (ALP) activity, quantitative alizarin red S staining, and quantitative reverse transcription-polymerase chain reaction (qRT-PCR) analyses were performed to investigate and compare the osteo/odontogenic induction potential of MTA on the Ad/BM-MSCs. The results of cytotoxicity assay revealed that at different concentrations, MTA-conditioned medium was not only biocompatible toward both cell types, but also capable of promoting cell proliferation. ALP activity assay showed that 0.2 mg/mL was the optimal concentration of MTA-conditioned medium for osteo/odontogenic induction in Ad/BM-MSCs. The expression of osteo/odontogenic gene markers was increased in Ad/BM-MSCs treated with 0.2 mg/mL MTA-conditioned media. Our results indicated that MTA can efficiently enhance the osteo/odontogenic potential of Ad-MSCs, and thus they can be considered as a better cell source for dentin-pulp complex regeneration. However, further investigations are required to test these potentials in animal models.

MTA Enhances the Potential of Adipose-Derived Mesenchymal Stem Cells for Dentin-Pulp Complex Regeneration.

Biopolymers are widely accepted natural materials in regenerative medicine, and further development of their bioactivities and discoveries on their composition/function relationships could greatly advance the field. However, a concise insight on commonly investigated biopolymers, their current applications and outlook of their modifications for multibioactivity are scarce. This review bridges this gap for professionals and especially freshmen in the field who are also interested in modification methods not yet in commercial use. A series of polymeric materials in research and development uses are presented as well as challenges that limit their efficacy in tissue regeneration are discussed. Finally, their roles in the regeneration of select tissues including the skin, bone, cartilage, and tendon are highlighted along with modifiable biopolymer moieties for different bioactivities.

Bioactive Polymeric Materials for the Advancement of Regenerative Medicine.

Mucus layers (McLs) are on the front line of the human defense system that protect us from foreign abiotic/biotic particles (e.g., airborne virus SARS-CoV-2) and lubricates our organs. Recently, the impact of McLs on human health (e.g., nutrient absorption and drug delivery) and diseases (e.g., infections and cancers) has been studied extensively, yet their mechanisms are still not fully understood due to their high variety among organs and individuals. We characterize these variances as the heterogeneity of McLs, which lies in the thickness, composition, and physiology, making the systematic research on the roles of McLs in human health and diseases very challenging. To advance mucosal organoids and develop effective drug delivery systems, a comprehensive understanding of McLs' heterogeneity and how it impacts mucus physiology is urgently needed. When the role of airway mucus in the penetration and transmission of coronavirus (CoV) is considered, this understanding may also enable a better explanation and prediction of the CoV's behavior. Hence, in this Review, we summarize the variances of McLs among organs, health conditions, and experimental settings as well as recent advances in experimental measurements, data analysis, and model development for simulations.

From Static to Dynamic: A Review on the Role of Mucus Heterogeneity in Particle and Microbial Transport.

The artificial lung has provided life-saving support for pulmonary disease patients and recently afforded patients with severe cases of COVID-19 better prognostic outcomes. While it addresses a critical medical need, reducing the risk of clotting inside the device remains challenging. Herein, a two-step surface coating process of the lung circuit using Zwitterionic polysulfobetaine methacrylate is evaluated for its nonspecific protein antifouling activity. It is hypothesized that similarly applied coatings on materials integrated (IT) or nonintegrated (NIT) into the circuit will yield similar antifouling activity. The effects of human plasma preconditioned with nitric oxide-loaded liposome on platelet (plt) fouling are also evaluated. Fibrinogen antifouling activities in coated fibers are similar in the IT and NIT groups. It however decreases in coated polycarbonate (PC) in the IT group. Also, plt antifouling activity in coated fibers is similar in the IT and NIT groups and is lower in coated PC and Tygon in the IT group compared to the NIT group. Coating process optimization in the IT lung circuit may help address difference in the coating appearance of outer and inner fiber bundle fibers, and the NO-liposome significantly reduces (86%) plt fouling on fibers indicating its potential use for blood anticoagulation.

Zwitterionic Polysulfobetaine Coating and Antiplatelet Liposomes Reduce Fouling in Artificial Lung Circuits.

Blood-bearing medical devices are essential for the delivery of critical care medicine and are often required to function for weeks to months. However, thrombus formation on their surfaces can lead to reduced device function and failure and expose patients to systemic thrombosis risks. While clinical anticoagulants reduce device related thrombosis, they also increase patient bleeding risk. The root cause of device thrombosis and inflammation is protein adsorption on the biomaterial surfaces of these devices. Protein adsorption activates the coagulation cascade and complement, and this, in turn, activates platelets and white blood cells. Surface modifications with zwitterionic polymers are particularly effective at reducing protein adsorption as well as conformational changes in proteins due to their hydrophilicity. Multiple coating strategies have been developed using carboxybetaine (CB), sulfobetaine (SB), and 2-methacryloyloxyethyl phosphorylcholine (MPC) zwitterionic polymers applied to the metals and hydrophobic polymers that make up the bulk of blood-bearing medical devices. These coatings have been highly successful at creating large reductions in protein adsorption and platelet adhesion during studies on the order of hours on flat surfaces and at reducing thrombus formation for up to a few days in full medical devices. Future work needs to focus on their ability to limit inflammation, particularly during hemodialysis, and in providing anticoagulation on the order of weeks, particularly in artificial lungs.

Kagya Amoako

Department of Chemistry and Chemical & Biomedical Engineering

University of New Haven

Artificial Lung Device Priming for In Situ Fiber Bundle Surface Grafting

Kagya Amoako

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Department of Chemistry and Chemical & Biomedical Engineering

University of New Haven

Artificial Lung Device Priming for In Situ Fiber Bundle Surface Grafting

Department of Chemistry and Chemical & Biomedical Engineering