1. Montaje de la paredes de la cámara <ol><li> Tome dos láminas de vidrio plano, marca la mitad en los dos extremos y con una regla recta filo como una guía, la puntuación de la copa con el cortador de diamantes. </li><li> Deslice el cortador de diamantes de ida y vuelta varias veces hasta que escuche un chirrido. </li><li> Lavar el vaso, y sujetándolo con dos toallas de papel en un recipiente de vidrio roto, se aplican cerca de una leve presión sobre la línea marcada con el lado marcado de espaldas a usted a romper la diapositiva en dos mitades. </li><li> Generosamente aplicar el adhesivo de vidrio a lo largo de un borde de un pedazo de vidrio y empujar una segunda pieza de vidrio contra el adhesivo en ángulo recto a la primera pieza. Coloque sobre una superficie plana (papel de aluminio, papel encerado o de papel normal) y permita que se asiente durante por lo menos una hora. </li><li> Después de una hora, repetir la aplicación de la etapa de adhesivo para formar una cámara cuadrada y deje que endurezca durante la noche. <img src="/files/ftp_upload/old/155_2008_9_3_3/155_figure-01.png" alt="Figura 1" width="358" height="266" /> </li></ol> 2. La colocación de las paredes de una placa de Petri <ol><li> Tome la parte superior de una placa de Petri y relleno a una profundidad de al menos 5 mm con una solución caliente de agarosa al 2% (de microondas de la agarosa en agua destilada hasta que se disuelva completamente). </li><li> Espere unos minutos, pero al mismo tiempo disuelto, el lugar de las paredes de la cámara en el centro del plato. Tome la parte inferior de la placa de Petri, lugar que parte de abajo hacia arriba. Usando una aguja calentada al fuego directo de disección, hacer una serie de pequeños agujeros (&gt; 1 mm) en el centro del plato para la ventilación. Hacer un agujero más grande (~ 4 mm de diámetro) ligeramente hacia un lado para la introducción de moscas de la cámara. Coloque un pedazo de cinta de etiquetas removibles sobre el agujero más grande. <img src="/files/ftp_upload/old/155_2008_9_3_4/155_figure-02.png" alt="Figura 2" width="447" height="207" /> <img src="/files/ftp_upload/old/155_2008_9_3_5/155_figure-03.png" alt="Figura 3" width="328" height="211" /> </li></ol> 3. Hacer la copa de alimentos <ol><li> Calentar un frasco de comida volar hasta el punto donde se funde la comida. Use una pipeta Pasteur para la transferencia de alimentos a un cierre vial de centelleo de relleno para formar una superficie plana en la parte superior. Tenga cuidado para evitar burbujas de aire y deje que se enfríe. </li><li> Preparar la pasta de levadura fresca de molienda de una pequeña cantidad de levadura seca y unas gotas de agua en un mortero. Agregar más levadura o el agua hasta que la consistencia es lo suficientemente gruesa como para permitir una caída visible pequeños para ser recogido por un palillo de dientes y se aplica al centro de la superficie del alimento. </li><li> Coloque el vial de alimentos en el centro de la cámara y coloque la parte inferior de la placa de Petri, en posición invertida para que los lados son y no entorpecer la visión, en la parte superior de la cámara. Introducir dos 3-5 moscas de un día por la aspiración a la cámara a través del agujero más grande en la parte superior. Cubrir el agujero con cinta adhesiva y coloque un trozo de papel de filtro negro con un corte de 2 cm agujero en el plato superior. </li><li> Coloque una lámpara de escritorio encima de la cámara, lo suficientemente lejos para que no se calienta en la cámara, y de modo que se ilumina la superficie del alimento. Todo el conjunto ideal debe ser colocado en un ambiente con alta humedad y una temperatura de 22-25 º C. <img src="/files/ftp_upload/old/155_2008_9_3_6/155_figure-04.png" alt="Figura 4" width="284" height="212" /> </li></ol> 4. Comience grabando a través de la pared frontal de la cámara cuando los dos moscas en el foodsurface.

studying aggression in drosophila (fruit flies)

La agresión es una conducta innata que se desarrolló en el marco de la defensa o la obtención de recursos. Este comportamiento social complejo está influenciada por factores genéticos, hormonales y ambientales. En muchos organismos, la agresión es fundamental para la supervivencia, pero la agresión el control y represión en diferentes contextos también se ha convertido cada vez más importante. En los últimos años, los invertebrados se han convertido en cada vez más útiles como sistemas modelo para investigar la base biológica genética y los sistemas de comportamiento social complejo. Esto se debe en parte al repertorio diverso de comportamientos exhibidos por estos organismos. En el video que lo acompaña, se describe un método para el análisis de la agresión en Drosophila, cuyo diseño incluye importantes eco-etológicas limitaciones. Los detalles incluyen medidas para: hacer una cámara de combate, aislamiento y pintura de las moscas, las moscas de la adición a la cámara de lucha y combate la filmación en vídeo. Este enfoque está siendo utilizado para identificar genes candidatos importantes en la agresión y en la elaboración de los circuitos neuronales que subyace a la salida de la agresión y otras conductas sociales.

Watch this Scientific Journal Video about Studying Aggression in Drosophila fruit flies at JoVE.com

Studying Aggression in Drosophila fruit flies

El estudio de la agresión en Drosophila (mosca de la fruta)

Aggression is an innate behavior that evolved in the framework of defending or obtaining resources.  This complex social behavior is influenced by ...

studying-aggression-in-drosophila-fruit-flies

Research

JoVE Journal

Biology

Studying Aggression in Drosophila (fruit flies)

Video: Studying Aggression in Drosophila fruit flies

Microinjection Techniques for Studying Mitosis in the Drosophila melanogaster Syncytial Embryo

This protocol describes the use of the Drosophila melanogaster syncytial embryo for studying mitosis1. Drosophila has useful genetics with a sequenced genome, and it can be easily maintained and manipulated. Many mitotic mutants exist, and transgenic flies expressing functional fluorescently (e.g. GFP) - tagged mitotic proteins have been and are being generated. Targeted gene expression is possible using the GAL4/UAS system2. 

The Drosophila early embryo carries out multiple mitoses very rapidly (cell cycle duration, &asymp;10 min). It is well suited for imaging mitosis, because during cycles 10-13, nuclei divide rapidly and synchronously without intervening cytokinesis at the surface of the embryo in a single monolayer just underneath the cortex. These rapidly dividing nuclei probably use the same mitotic machinery as other cells, but they are optimized for speed; the checkpoint is generally believed to not be stringent, allowing the study of mitotic proteins whose absence would cause cell cycle arrest in cells with a strong checkpoint. Embryos expressing GFP labeled proteins or microinjected with fluorescently labeled proteins can be easily imaged to follow live dynamics (Fig. 1). In addition, embryos can be microinjected with function-blocking antibodies or inhibitors of specific proteins to study the effect of the loss or perturbation of their function3. These reagents can diffuse throughout the embryo, reaching many spindles to produce a gradient of concentration of inhibitor, which in turn results in a gradient of defects comparable to an allelic series of mutants. Ideally, if the target protein is fluorescently labeled, the gradient of inhibition can be directly visualized4. It is assumed that the strongest phenotype is comparable to the null phenotype, although it is hard to formally exclude the possibility that the antibodies may have dominant effects in rare instances, so rigorous controls and cautious interpretation must be applied. Further away from the injection site, protein function is only partially lost allowing other functions of the target protein to become evident.

Microinjection Techniques for Studying Mitosis in the Drosophila melanogaster Syncytial Embryo

This protocol describes the use of microinjection and high resolution imaging in the Drosophila melanogaster syncytial embryo to study mitosis.

Técnicas de microinyección para el estudio de la mitosis en el Drosophila melanogaster Embrión sincitial

This protocol describes the use of the Drosophila melanogaster syncytial embryo  for studying mitosis1.  Drosophila has useful genetics with a sequenced ...

Investigación

Biología

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may also be used to study the structure-function relationship for other ion channels and neurotransmitter receptors1. BK channels are widely expressed in different tissues and have been implicated in many physiological functions, including regulation of smooth muscle contraction, frequency tuning of inner hair cells and regulation of neurotransmitter release2-6. BK channels are activated by membrane depolarization and by intracellular Ca2+ and Mg2+ 6-9. Therefore, the protocol is designed to control both the membrane voltage and the intracellular solution. In this protocol, messenger RNA of BK channels is injected into Xenopus laevis oocytes (stage V-VI) followed by 2-5 days of incubation at 18&deg;C10-13. Membrane patches that contain single or multiple BK channels are excised with the inside-out configuration using patch clamp techniques10-13. The intracellular side of the patch is perfused with desired solutions during recording so that the channel activation under different conditions can be examined. To summarize, the mRNA of BK channels is injected into Xenopus laevis oocytes to express channel proteins on the oocyte membrane; patch clamp techniques are used to record currents flowing through the channels under controlled voltage and intracellular solutions.

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Ionic current of BK channels is recorded using patch clamp techniques. BK channels are expressed in Xenopus oocytes by injecting messenger RNA. The intracellular solution during patch clamp recordings is controlled by a perfusion system.

Patch clamp y técnicas de perfusión para el estudio de los canales iónicos expresados ​​en Xenopus Ovocitos

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may ...

Imaging Cell Shape Change in Living Drosophila Embryos

The developing Drosophila melanogaster embryo undergoes a number of cell shape changes that are highly amenable to live confocal imaging. Cell shape changes in the fly are analogous to those in higher organisms, and they drive tissue morphogenesis. So, in many cases, their study has direct implications for understanding human disease (Table 1)1-5. On the sub-cellular scale, these cell shape changes are the product of activities ranging from gene expression to signal transduction, cell polarity, cytoskeletal remodeling and membrane trafficking. Thus, the Drosophila embryo provides not only the context to evaluate cell shape changes as they relate to tissue morphogenesis, but also offers a completely physiological environment to study the sub-cellular activities that shape cells.
The protocol described here is designed to image a specific cell shape change called cellularization. Cellularization is a process of dramatic plasma membrane growth, and it ultimately converts the syncytial embryo into the cellular blastoderm. That is, at interphase of mitotic cycle 14, the plasma membrane simultaneously invaginates around each of ~6000 cortically anchored nuclei to generate a sheet of primary epithelial cells. Counter to previous suggestions, cellularization is not driven by Myosin-2 contractility6, but is instead fueled largely by exocytosis of membrane from internal stores7. Thus, cellularization is an excellent system for studying membrane trafficking during cell shape changes that require plasma membrane invagination or expansion, such as cytokinesis or transverse-tubule (T-tubule) morphogenesis in muscle.
Note that this protocol is easily applied to the imaging of other cell shape changes in the fly embryo, and only requires slight adaptations such as changing the stage of embryo collection, or using "embryo glue" to mount the embryo in a specific orientation (Table 1)8-19. In all cases, the workflow is basically the same (Figure 1). Standard methods for cloning and Drosophila transgenesis are used to prepare stable fly stocks that express a protein of interest, fused to Green Fluorescent Protein (GFP) or its variants, and these flies provide a renewable source of embryos. Alternatively, fluorescent proteins/probes are directly introduced into fly embryos via straightforward micro-injection techniques9-10. Then, depending on the developmental event and cell shape change to be imaged, embryos are collected and staged by morphology on a dissecting microscope, and finally positioned and mounted for time-lapse imaging on a confocal microscope.

Imaging Cell Shape Change in Living Drosophila Embryos

Early development of the fruit fly, Drosophila melanogaster, is characterized by a number of cell shape changes that are well suited for imaging approaches. This article will describe basic tools and methods required for live confocal imaging of Drosophila embryos, and will focus on a cell shape change called cellularization.

Celular imagen Cambiar forma de vida Drosophila Los embriones

The developing Drosophila melanogaster embryo undergoes a number of cell shape changes that are highly amenable to live confocal imaging.  Cell shape ...

An Optimized Protocol for Rearing Fopius arisanus, a Parasitoid of Tephritid Fruit Flies

Fopius arisanus (Sonan) is an important parasitoid of Tephritid fruit flies for at least two reasons. First, it is the one of only three opiine parasitoids known to infect the host during the egg stage1. Second, it has a wide range of potential fruit fly hosts. Perhaps due to its life history, F. arisanus has been a successfully used for biological control of fruit flies in multiple tropical regions2-4. One impediment to the wide use of F. arisanus for fruit fly control is that it is difficult to establish a stable laboratory colony5-9. Despite this difficulty, in the 1990s USDA researchers developed a reliable method to maintain laboratory populations of F. arisanus10-12. There is significant interest in F. arisanus biology13,14, especially regarding its ability to colonize a wide variety of Tephritid hosts14-17; interest is especially driven by the alarming spread of Bactrocera fruit fly pests to new continents in the last decade18. Further research on F. arisanus and additional deployments of this species as a biological control agent will benefit from optimizations and improvements of rearing methods. In this protocol and associated video article we describe an optimized method for rearing F. arisanus based on a previously described approach12. The method we describe here allows rearing of F. arisanus in a small scale without the use of fruit, using materials available in tropical regions around the world and with relatively low manual labor requirements.

An Optimized Protocol for Rearing Fopius arisanus, a Parasitoid of Tephritid Fruit Flies

Fopius arisanus is an egg-larval parasitoid of Tephritid fruit flies that is successfully used in biological control of these important tropical pests. We describe here an optimized protocol for rearing F. arisanus on a small scale using readily available materials.

Un protocolo optimizado para cría Fopius arisanus, Un parasitoide de moscas de fruta tefrítidas

Fopius arisanus (Sonan) is an important parasitoid of Tephritid fruit flies for at least two reasons. First, it is the one of only three opiine ...

Isolation and Biophysical Study of Fruit Cuticles

The cuticle, a hydrophobic protective layer on the aerial parts of terrestrial plants, functions as a versatile defensive barrier to various biotic and abiotic stresses and also regulates water flow from the external environment.1 A biopolyester (cutin) and long-chain fatty acids (waxes) form the principal structural framework of the cuticle; the functional integrity of the cuticular layer depends on the outer 'epicuticular' layer as well as the blend consisting of the cutin biopolymer and 'intracuticular' waxes.2 Herein, we describe a comprehensive protocol to extract waxes exhaustively from commercial tomato (Solanum lycopersicum) fruit cuticles or to remove epicuticular and intracuticular waxes sequentially and selectively from the cuticle composite. The method of Jetter and Sch&auml;ffer (2001) was adapted for the stepwise extraction of epicuticular and intracuticular waxes from the fruit cuticle.3,4 To monitor the process of sequential wax removal, solid-state cross-polarization magic-angle-spinning (CPMAS) 13C NMR spectroscopy was used in parallel with atomic force microscopy (AFM), providing molecular-level structural profiles of the bulk materials complemented by information on the microscale topography and roughness of the cuticular surfaces. To evaluate the cross-linking capabilities of dewaxed cuticles from cultivated wild-type and single-gene mutant tomato fruits, MAS 13C NMR was used to compare the relative proportions of oxygenated aliphatic (CHO and CH2O) chemical moieties.
Exhaustive dewaxing by stepwise Soxhlet extraction with a panel of solvents of varying polarity provides an effective means to isolate wax moieties based on the hydrophobic characteristics of their aliphatic and aromatic constituents, while preserving the chemical structure of the cutin biopolyester. The mechanical extraction of epicuticular waxes and selective removal of intracuticular waxes, when monitored by complementary physical methodologies, provides an unprecedented means to investigate the cuticle assembly: this approach reveals the supramolecular organization and structural integration of various types of waxes, the architecture of the cutin-wax matrix, and the chemical composition of each constituent. In addition, solid-state 13C NMR reveals differences in the relative numbers of CHO and CH2O chemical moieties for wild-type and mutant red ripe tomato fruits. The NMR techniques offer exceptional tools to fingerprint the molecular structure of cuticular materials that are insoluble, amorphous, and chemically heterogeneous. As a noninvasive surface-selective imaging technique, AFM furnishes an effective and direct means to probe the structural organization of the cuticular assembly on the nm-&mu;m length scale.

Aerial plant organs are protected by the cuticle, a supramolecular biopolyester-wax assembly. We present protocols to monitor selective removal of epi- and intracuticular waxes from tomato fruit cuticles on molecular and micro scales by solid-state NMR and atomic force microscopy, respectively, and to assess the cross-linking capacity of engineered cuticular biopolyesters.

El aislamiento y estudio biofísico de las cutículas de fruta

The cuticle, a hydrophobic protective layer on the aerial parts of terrestrial plants, functions as a versatile defensive barrier to various biotic and ...

Studying Mitotic Checkpoint by Illustrating Dynamic Kinetochore Protein Behavior and Chromosome Motion in Living Drosophila Syncytial Embryos

The spindle assembly checkpoint (SAC) mechanism is an active signal, which monitors the interaction between chromosome kinetochores and spindle microtubules to prevent anaphase onset until the chromosomes are properly connected. Cells use this mechanism to prevent aneuploidy or genomic instability, and hence cancers and other human diseases like birth defects and Alzheimer's1. A number of the SAC components such as Mad1, Mad2, Bub1, BubR1, Bub3, Mps1, Zw10, Rod and Aurora B kinase have been identified and they are all kinetochore dynamic proteins2. Evidence suggests that the kinetochore is where the SAC signal is initiated. The SAC prime regulatory target is Cdc20. Cdc20 is one of the essential APC/C (Anaphase Promoting Complex or Cyclosome) activators3 and is also a kinetochore dynamic protein4-6. When activated, the SAC inhibits the activity of the APC/C to prevent the destruction of two key substrates, cyclin B and securin, thereby preventing the metaphase to anaphase transition7,8. Exactly how the SAC signal is initiated and assembled on the kinetochores and relayed onto the APC/C to inhibit its function still remains elusive.
Drosophila is an extremely tractable experimental system; a much simpler and better-understood organism compared to the human but one that shares fundamental processes in common. It is, perhaps, one of the best organisms to use for bio-imaging studies in living cells, especially for visualization of the mitotic events in space and time, as the early embryo goes through 13 rapid nuclear division cycles synchronously (8-10 minutes for each cycle at 25 &deg;C) and gradually organizes the nuclei in a single monolayer just underneath the cortex9.
Here, I present a bio-imaging method using transgenic Drosophila expressing GFP (Green Fluorescent Protein) or its variant-targeted proteins of interest and a Leica TCS SP2 confocal laser scanning microscope system to study the SAC function in flies, by showing images of GFP fusion proteins of some of the SAC components, Cdc20 and Mad2, as the example.

Studying Mitotic Checkpoint by Illustrating Dynamic Kinetochore Protein Behavior and Chromosome Motion in Living Drosophila Syncytial Embryos

The kinetochore is where the SAC initiates its signal monitoring the mitotic segregation of the sister chromatids. A method is described to visualize the recruitment and turnover of one of the kinetochore proteins and its coordination with the chromosome motion in Drosophila embryos using a Leica laser scanning confocal system.

El estudio de puesto de control mitótico, ilustrando comportamiento dinámico de proteínas cinetocoro y el movimiento de cromosomas en vivo<em&gt; Drosophila</em&gt; Los embriones Sincitial

The spindle assembly checkpoint (SAC) mechanism is an active signal, which monitors the interaction between chromosome kinetochores and spindle ...

Fruit Volatile Analysis Using an Electronic Nose

Numerous and diverse physiological changes occur during fruit ripening, including the development of a specific volatile blend that characterizes fruit aroma. Maturity at harvest is one of the key factors influencing the flavor quality of fruits and vegetables1. The validation of robust methods that rapidly assess fruit maturity and aroma quality would allow improved management of advanced breeding programs, production practices and postharvest handling. 
Over the last three decades, much research has been conducted to develop so-called electronic noses, which are devices able to rapidly detect odors and flavors2-4. Currently there are several commercially available electronic noses able to perform volatile analysis, based on different technologies. The electronic nose used in our work (zNose, EST, Newbury Park, CA, USA), consists of ultra-fast gas chromatography coupled with a surface acoustic wave sensor (UFGC-SAW). This technology has already been tested for its ability to monitor quality of various commodities, including detection of deterioration in apple5; ripeness and rot evaluation in mango6; aroma profiling of thymus species7; C6 volatile compounds in grape berries8; characterization of vegetable oil9 and detection of adulterants in virgin coconut oil10. 
This system can perform the three major steps of aroma analysis: headspace sampling, separation of volatile compounds, and detection. In about one minute, the output, a chromatogram, is produced and, after a purging cycle, the instrument is ready for further analysis. The results obtained with the zNose can be compared to those of other gas-chromatographic systems by calculation of Kovats Indices (KI). Once the instrument has been tuned with an alkane standard solution, the retention times are automatically converted into KIs. However, slight changes in temperature and flow rate are expected to occur over time, causing retention times to drift. Also, depending on the polarity of the column stationary phase, the reproducibility of KI calculations can vary by several index units11. A series of programs and graphical interfaces were therefore developed to compare calculated KIs among samples in a semi-automated fashion. These programs reduce the time required for chromatogram analysis of large data sets and minimize the potential for misinterpretation of the data when chromatograms are not perfectly aligned.
We present a method for rapid volatile compound analysis in fruit. Sample preparation, data acquisition and handling procedures are also discussed.

A rapid method for volatile compound analysis in fruit is described. The volatile compounds present in the headspace of a homogenate of the sample are rapidly separated and detected with ultra-fast gas chromatography (GC) coupled with a surface acoustic wave (SAW) sensor. A procedure for data handling and analysis is also discussed.

Frutas volátil análisis mediante una nariz electrónica

Numerous and diverse physiological changes occur during fruit ripening, including the development of a specific volatile blend that characterizes fruit ...

Studying Mitochondrial Structure and Function in Drosophila Ovaries

Analysis of the mitochondrial structure-function relationship is required for a thorough understanding of the regulatory mechanisms of mitochondrial functionality. Fluorescence microscopy is an indispensable tool for the direct assessment of mitochondrial structure and function in live cells and for studying the mitochondrial structure-function relationship, which is primarily modulated by the molecules governing fission and fusion events between mitochondria. This paper describes and demonstrates specific methods for studying mitochondrial structure and function in live as well as in fixed tissue in the model organism Drosophila melanogaster. The tissue of choice here is the Drosophila ovary, which can be isolated and made amenable for ex vivo live confocal microscopy. Furthermore, the paper describes how to genetically manipulate the mitochondrial fission protein, Drp1, in Drosophila ovaries to study the involvement of Drp1-driven mitochondrial fission in modulating the mitochondrial structure-function relationship. The broad use of such methods is demonstrated in already-published as well as in novel data. The described methods can be further extended towards understanding the direct impact of nutrients and/or growth factors on the mitochondrial properties ex vivo. Given that mitochondrial dysregulation underlies the etiology of various diseases, the described innovative methods developed in a genetically tractable model organism, Drosophila, are anticipated to contribute significantly to the understanding of the mechanistic details of the mitochondrial structure-function relationship and to the development of mitochondria-directed therapeutic strategies.

Studying Mitochondrial Structure and Function in Drosophila Ovaries

Analysis of the mitochondrial structure-function relationship is required for a thorough understanding of the regulatory mechanisms of mitochondrial functionality. Specific methods for studying mitochondrial structure and function in live and fixed Drosophila ovaries are described and demonstrated in this paper.

Estudiar mitocondrial Estructura y función en<em&gt; Drosophila</em&gt; Los ovarios

Analysis of the mitochondrial structure-function relationship is required for a thorough understanding of the regulatory mechanisms of mitochondrial ...

Laboratory Rearing of Stable Flies and Other Muscoid Diptera

Stable flies, Stomoxys calcitrans, are serious pests of livestock, humans, companion animals and wildlife worldwide. During the last 20+ years, changes in agronomic practices resulted in serious outbreaks of stable flies in several countries. These outbreaks disrupted livestock production and human recreation resulting in public demands for increasing research and management efforts for this pest. A simple and inexpensive procedure for rearing stable flies for laboratory studies is presented. The procedure uses locally available diet components, equipment and supplies. The procedure can be adapted for rearing other muscoid flies including face fly (Musca autumnalis), horn fly (Haematobia irritans), and house fly (Musca domestica). The procedure produces stable fly puparia averaging 12.5 mg and ~35% egg to adult survival. Approximately 3000 flies are produced in each pan.

A procedure for rearing stable flies (Stomoxys calcitrans) is presented. The procedure uses locally available materials for diet components, equipment and supplies.

Laboratorio de cría de moscas de los establos y otros dípteros afines

Stable flies, Stomoxys calcitrans, are serious pests of livestock, humans, companion animals and wildlife worldwide. During the last 20+ years, changes in ...

Simple Homemade Tools to Handle Fruit Flies&#8212;Drosophila melanogaster

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in practice, as adult flies fly. Demonstrated here is how to make some simple and cost-effective tools to address difficult issues in the handling of Drosophila. Holes in foam stoppers are made and pipette tips or funnels are inserted into the holes. Flies then move only in one direction into the pipette tip/funnel assemblage, allowing efficient control of the transfer of adult Drosophila into or out of a vial. Existing protocols have been modified for cool-anesthetizing flies by chilling in crushed ice and transferring them onto a cold, hard icepack surface. The icepack is covered with a piece of medical gauze that keeps immobilized flies from the condensed water when examined under a stereomicroscope. The flies are finally euthanized for counting and sorting or discarded by microwaving. A bottle-shaped cage has also been developed for collecting eggs, as well as a labor-saving device and accompanying protocol for cleaning glass culture vials.

Simple Homemade Tools to Handle Fruit Flies&amp;#8212;&lt;em&gt;Drosophila melanogaster&lt;/em&gt;

Described here is the use of several homemade tools to transfer, chill, and kill adult Drosophila, as well as to clean glass culture vials and collect eggs. These tools are easy to make and are rather efficient in handling Drosophila.

Herramientas caseras simples para manejar moscas de la fruta—Drosophila melanogaster

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in ...