self-assembly-hybrid-lipid-membranes-doped-with-hydrophobic-organic

Self-Assembly of Hybrid Lipid Membranes Doped with Hydrophobic Organic Molecules at the Water/Air Interface

Because of their unique properties, including an ultrathin thickness (3-4 nm), ultrahigh resistivity, fluidity and self-assembly ability, lipid bilayers ...

Tohoku University

Solution-processable organometal perovskite materials have been widely used in various kinds of devices. In these devices, the perovskite materials normally act as active layers. Grain boundaries and structural disorder in the perovskite layer would interfere the charge transport and increase recombination probability. Here we proposed a novel fabrication method to dramatically increase the crystal size by more than 20 times as compared with previously reported values. Exceptional structural order in the large crystals is illustrated by nanoscale surface morphology and a simple recrystallization method. Because of reduced grain boundaries and increased crystal order in perovskite layers, the lateral charge transport is significantly improved, as demonstrated by conductive atomic-force microscopy and performance of photodetectors. This deposition technology paves the way for future high-performance devices based on perovskite thin films.

Fabrication and Characterization of High-Quality Perovskite Films with Large Crystal Grains.

The self-assembled bilayer lipid membrane (BLM) is the basic component of the cell membrane. The reconstitution of ion channel proteins in artificially formed BLMs represents a well-defined system for the functional analysis of ion channels and screening the effects of drugs that act on them. However, because BLMs are unstable, this limits the experimental throughput of BLM reconstitution systems. Here we report on the formation of mechanically stable solvent-free BLMs in microfabricated apertures with defined nano- and micro-tapered edge structures. The role of such nano- and micro-tapered structures on the stability of the BLMs was also investigated. Finally, this BLM system was combined with a cell-free synthesized human ether-a-go-go-related gene channel, a cardiac potassium channel whose relation to arrhythmic side effects following drug treatment is well recognized. Such stable BLMs as these, when combined with a cell-free system, represent a potential platform for screening the effects of drugs that act on various ion-channel genotypes.

Mechanically stable solvent-free lipid bilayers in nano- and micro-tapered apertures for reconstitution of cell-free synthesized hERG channels.

Artificial bilayer lipid membranes (BLMs) provide well-defined systems for investigating the fundamental properties of membrane proteins, including ion channels, and for screening the effect of drugs that act on them. However, the application of this technique is limited due to the low stability and low reconstitution efficiency of the process. We previously reported on improving the stability of BLM based on the fabrication of microapertures having a tapered edge in SiO/SiN septa and efficient ion channel incorporation based on vesicle fusion accelerated by a centrifugal force. Although the BLM stability and incorporation probability were dramatically improved when these approaches were used, some BLMs were ruptured when subjected to a centrifugal force. To further improve the BLM stability, we investigated the effect of modifying the surface of the SiO/SiN septa on the stability of BLM suspended in the septa. The modified surfaces were characterized in terms of hydrophobicity, lipophobicity, and surface roughness. Diffusion coefficients of the lipid monolayers formed on the modified surfaces were also determined. Highly fluidic lipid monolayers were formed on the amphiphobic substrates that had been modified with long-chain perfluorocarbons. Free-standing BLMs formed in amphiphobic septa showed a much higher mechanical stability, including tolerance to water movement and applied centrifugal forces with and without proteoliposomes, than those formed in the septa that had been modified with a short alkyl chain. These results demonstrate that highly stable BLMs are formed when the surface of the septa has amphiphobic properties. Because highly fluidic lipid monolayers that are formed on the septa seamlessly connect with BLMs in a free-standing region, the high fluidity of the lipids contributes to decreasing potential damage to BLMs when mechanical stresses are applied. This approach to improve the BLM stability increases the experimental efficiency of the BLM systems and will contribute to the development of high-throughput platforms for functional assays of ion channel proteins.

Amphiphobic Septa Enhance the Mechanical Stability of Free-Standing Bilayer Lipid Membranes.

We report on a novel lipid bilayer system, in which a lateral bias can be applied in addition to a conventional transmembrane voltage. Freestanding bilayer lipid membranes (BLMs) doped with [6,6]-phenyl-C-butyric acid methyl ester (PCBM) were formed in a microaperture, around which metal electrodes were deposited. Using this system, it was possible to modulate and amplify photoinduced transmembrane currents by applying a lateral bias along the BLM. The results indicate that the microfabricated Si chip with embedded electrodes is a promising platform for the formation of transistor-like devices based on PCBM-doped BLMs and have potential for use in a wide variety of nanohybrid devices.

Modulation of Photoinduced Transmembrane Currents in a Fullerene-Doped Freestanding Lipid Bilayer by a Lateral Bias.

An artificial cell membrane that is composed of bilayer lipid membranes (BLMs) with transmembrane proteins incorporated within them represents a well-defined system for the analysis of membrane proteins, especially ion channel proteins that are major targets for drug design. Because the BLM system has a high compatibility with recently developed cell-free expression systems, it has attracted attention as a next-generation drug screening system. However, three issues associated with BLM systems, i. e., their instability, the need for non-volatile organic solvents and a low efficiency of ion channel incorporation, have limited their use as a drug screening platform. In this personal account, we discuss our recent approaches to address these issues based on microfabrication. We also discuss the potential for using the BLM system combined with cell-free expression systems as a drug screening system for future personalized medicine.

Teng Ma

Advanced Institute for Materials Research

Tohoku University

Self-Assembly of Hybrid Lipid Membranes Doped with Hydrophobic Organic Molecules at the Water/Air Interface

Teng Ma

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Advanced Institute for Materials Research

Tohoku University

Self-Assembly of Hybrid Lipid Membranes Doped with Hydrophobic Organic Molecules at the Water/Air Interface

Advanced Institute for Materials Research