We would like to acknowledge Dionna Gamble, Allison Larson, and Katia Torres for assistance with model generation and measurements, Monica Mahre for manuscript assistance, Gary Williams for technical assistance, Jerrald Spencer Jr. for assistance with the figures and the Fairview Imaging Services at the University of Minnesota. 
Funding was received from the Institute for Engineering in Medicine (University of Minnesota) and in part from a research contract with Medtronic Inc.

Procedure
Table 1 summarizes the materials used during the process. Figure 1 provides an overview of the process.
1. Specimen and Scan Preparation
<ol>
	<li>Obtain the isolated human hearts fresh and subsequently perfusion fix them in 10% buffered formalin in their end-diastolic state.</li>
	<li>Rinse the hearts to be scanned in water the day before scanning in order to remove the majority of the formalin.</li>
	<li>Before heading to...

<ol>
	<li>Burkhardt, J. D., Wilkoff, B. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Interventional+electrophysiology+and+cardiac+resynchronization+therapy:+delivering+electrical+therapies+for+heart+failure.">Interventional electrophysiology and cardiac resynchronization therapy: delivering electrical therapies for heart failure.</a> Circ. 115, 2208-2220 (2007).</li><li>Lu, F., Iaizzo, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cardiac+resynchronization+therapy.">Cardiac resynchronization therapy.</a> Handbook of cardiac physiology and anatomy. , 475-497 (2009).</li><li>Eggen, M. D., Swingen, C. M., Iaizzo, P. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ex+vivo+diffusion+tensor+MRI+of+human+hearts:+relative+effects+of+specimen+decomposition.">Ex vivo diffusion tensor MRI of human hearts: relative effects of specimen decomposition.</a> Magn. Reson. Med. 67, 1703-1709 (2012).</li><li>Manzke, R., Binner, L., Bornstedt, A., Merkle, N., Lutz, A., Gradinger, R., Rasche, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+the+coronary+venous+system+in+heart+failure+patients+by+blood+pool+agent+enhanced+whole-heart+MRI.">Assessment of the coronary venous system in heart failure patients by blood pool agent enhanced whole-heart MRI.</a> Eur. Radiol. 21, 799-806 (2010).</li><li>Abbara, S., Cury, R. C., Nieman, K., Reddy, V., Moselewski, F., Schmidt, S., Ferencik, M., Hoffman, U., Brady, T. J., Achenbach, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Noninvasive+evaluation+of+cardiac+veins+with+16-MDCT+angiography.">Noninvasive evaluation of cardiac veins with 16-MDCT angiography.</a> AJR. Am. J. Roentgenol. 185, 1001-1006 (2005).</li><li>Gerber, T. C., Sheedy, P. F., Bell, M. R., Hayes, D. L., Rumberger, J. A., Behrenbeck, T., Holmes, D. R., Schwartz, R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+the+coronary+venous+system+using+electron+beam+computed+tomography.">Evaluation of the coronary venous system using electron beam computed tomography.</a> Int. J. Cardiovasc. Imaging. 17, 65-75 (2001).</li><li>Jongbloed, M. R. M., Lamb, H. J., Bax, J. J., Schuijf, J. D., de Roos, A., vander Wall, E. E., Schalij, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Noninvasive+visualization+of+the+cardiac+venous+system+using+multislice+computed+tomography.">Noninvasive visualization of the cardiac venous system using multislice computed tomography.</a> J. Am. Coll. Cardiol. 45, 749-753 (2005).</li><li>Mao, S., Shinbane, J. S., Girky, M. J., Child, J., Carson, S., Oudiz, R. J., Budoff, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coronary+venous+imaging+with+electron+beam+computed+tomographic+angiography:+three-dimensional+mapping+and+relationship+with+coronary+arteries.">Coronary venous imaging with electron beam computed tomographic angiography: three-dimensional mapping and relationship with coronary arteries.</a> Am. Heart J. 150, 315-322 (2005).</li><li>Muhlenbruch, G., Koos, R., Wildberger, J. E., Gunther, R. W., Mahnken, A. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Imaging+of+the+cardiac+venous+system:+comparison+of+MDCT+and+conventional+angiography.">Imaging of the cardiac venous system: comparison of MDCT and conventional angiography.</a> AJR. Am. J. Roentgenol. 185, 1252-1257 (2005).</li><li>Schaffler, G. J., Groell, R., Peichel, K. H., Rienmuller, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Imaging+the+coronary+venous+drainage+system+using+electron-beam+CT.">Imaging the coronary venous drainage system using electron-beam CT.</a> Surg. Radiol. Anat. 22, 35-39 (2000).</li><li>Tada, H., Kurosaki, K., Naito, S., Koyama, K., Itoi, K., Ito, S., Ueda, M., Shinbo, G., Hoshizaki, H., Nogami, A., Oshima, S., Taniguchi, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+visualization+of+the+coronary+venous+system+using+multidetector+row+computed+tomography.">Three-dimensional visualization of the coronary venous system using multidetector row computed tomography.</a> Circ. J. 69, 165-170 (2005).</li><li>Van de Veire, N. R., Schuijf, J. D., Sutter, J. D., Devos, D., Bleeker, G. B., de Roos, A., vander Wall, E. E., Schalij, M. J., Bax, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Non-invasive+visualization+of+the+cardiac+venous+system+in+coronary+artery+disease+patients+using+64-slice+computed+tomography.">Non-invasive visualization of the cardiac venous system in coronary artery disease patients using 64-slice computed tomography.</a> J. Am. Coll. Cardiol. 48, 1832-1838 (2006).</li><li>de Jong, P. A., Mayo, J. R., Golmohammadi, K., Nakano, Y., Lequin, M. H., Tiddens, H. A., Aldrich, J., Coxson, H. O., Sin, D. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Estimation+of+cancer+mortality+associated+with+repetitive+computed+tomography+scanning.">Estimation of cancer mortality associated with repetitive computed tomography scanning.</a> Am. J. Respir. Crit. Care Med. 173, 199-203 (2006).</li><li>Martin, D. R., Semelka, R. C., Chapman, A., Peters, H., Finn, P. J., Kalb, B., Thomsen, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nephrogenic+systemic+fibrosis+versus+contrast-induced+nephropathy:+risks+and+benefits+of+contrast-enhanced+MR+and+CT+in+renally+impaired+patients.">Nephrogenic systemic fibrosis versus contrast-induced nephropathy: risks and benefits of contrast-enhanced MR and CT in renally impaired patients.</a> J. Magn. Reson. Imaging. 30, 1350-1356 (2009).</li></ol>

Our laboratory is developing a library of perfusion-fixed heart specimens for various anatomical research studies. To date, we have over 240 preserved specimens. The specific methods we have used to prepare these specimens have been previously described3. The present study describes a novel methodology for mapping the human cardiac venous system and for the development of an anatomical database, which could be used for the design of cardiac devices employed within the vessels.
	<p class="jove_content...

anatomical reconstructions of the human cardiac venous system using contrast-computed tomography of perfusion-fixed specimens

A detailed understanding of the complexity and relative variability within the human cardiac venous system is crucial for the development of cardiac devices that require access to these vessels. For example, cardiac venous anatomy is known to be one of the key limitations for the proper delivery of cardiac resynchronization therapy (CRT)1 Therefore, the development of a database of anatomical parameters for human cardiac venous systems can aid in the design of CRT delivery devices to overcome such a limitation. In this research project, the anatomical parameters were obtained from 3D reconstructions of the venous system using contrast-computed tomography (CT) imaging and modeling software (Materialise, Leuven, Belgium). The following parameters were assessed for each vein: arc length, tortuousity, branching angle, distance to the coronary sinus ostium, and vessel diameter.
	CRT is a potential treatment for patients with electromechanical dyssynchrony. Approximately 10-20% of heart failure patients may benefit from CRT2. Electromechanical dyssynchrony implies that parts of the myocardium activate and contract earlier or later than the normal conduction pathway of the heart. In CRT, dyssynchronous areas of the myocardium are treated with electrical stimulation. CRT pacing typically involves pacing leads that stimulate the right atrium (RA), right ventricle (RV), and left ventricle (LV) to produce more resynchronized rhythms. The LV lead is typically implanted within a cardiac vein, with the aim to overlay it within the site of latest myocardial activation. 
	We believe that the models obtained and the analyses thereof will promote the anatomical education for patients, students, clinicians, and medical device designers. The methodologies employed here can also be utilized to study other anatomical features of our human heart specimens, such as the coronary arteries. To further encourage the educational value of this research, we have shared the venous models on our free access website: <a href="http://www.vhlab.umn.edu/atlas" target="_blank">www.vhlab.umn.edu/atlas</a>.

Table 2 presents the median anatomical parameters for the major cardiac veins for 42 human heart specimens. All heart specimens contained one posterior interventricular vein (PIV) and anterior interventricular vein (AIV). Some specimens contained more than one posterior vein of the LV (PVLV), postero-lateral vein (PLV), left lateral vein (LLV), and/or antero-lateral vein (ALV), while other hearts may not have had one or two of these specific veins present.
 <table border="1">
 <tbody>
 <t...

Watch this Scientific Journal Video about Anatomical Reconstructions of the Human Cardiac Venous System using Contrast-computed Tomography of Perfusion-fixed Specimens at JoVE.com

Anatomical Reconstructions of the Human Cardiac Venous System using Contrast-computed Tomography of Perfusion-fixed Specimens

The objective of this research is to recreate and then access the anatomy of the human cardiac venous system using 3D reconstructions generated from contrast-computed tomography scans.

A detailed  understanding of the complexity and relative variability within the human  cardiac venous system is crucial for the development of cardiac ...

anatomical-reconstructions-human-cardiac-venous-system-using-contrast

Research

JoVE Journal

Bioengineering

11.6K ビュー.  University of Minnesota. 本研究の目的は、再作成した後、造影コンピュータ断層撮影スキャンから生成された3次元再構成を用いたヒト心臓静脈系の解剖にアクセスすることです。

ビデオ: Anatomical Reconstructions of the Human Cardiac Venous System using Contrast-computed Tomography of Perfusion-fixed Specimens

The objective of this research is to recreate and then access the anatomy of the human cardiac venous system using 3D reconstructions generated from contrast-computed tomography...

in vivo quantitative assessment of myocardial structure, function, perfusion and viability using cardiac micro-computed tomography

In Vivo Quantitative Assessment of Myocardial Structure, Function, Perfusion and Viability Using Cardiac Micro-computed Tomography

This method outlines the use of Quantum Micro-Computed Tomography (MicroCT) to assess cardiac morphology, function, perfusion, metabolism and viability with iodinated contrast agent in mice with experimentally-induced myocardial ischemia. The technique can be applied for non-destructive high-throughput longitudinal in vivo imaging of various animal models of human heart disease.

In Vivo Quantitative Assessment of Myocardial Structure, Function, Perfusion and Viability Using Cardiac Micro-computed Tomography

tissue preparation techniques for contrast-enhanced micro computed tomography imaging of large mammalian cardiac models with chronic disease

Tissue Preparation Techniques for Contrast-Enhanced Micro Computed Tomography Imaging of Large Mammalian Cardiac Models with Chronic Disease

Here, we present a protocol to obtain high resolution micro computed tomography images of healthy and pathological large mammalian whole hearts with collagen-selective contrast...

rigid embedding of fixed and stained, whole, millimeter-scale specimens for section-free 3d histology by micro-computed tomography

Rigid Embedding of Fixed and Stained, Whole, Millimeter-Scale Specimens for Section-free 3D Histology by Micro-Computed Tomography

We developed protocols and designed a custom apparatus to enable embedding of millimeter-scale specimens. We present sample preparation procedures with an emphasis on embedding in acrylic resin and polyimide tubing to achieve rigid immobilization and long-term storage of specimens for the interrogation of tissue architecture and cell morphology by...

high-resolution cardiac positron emission tomography/computed tomography for small animals

High-Resolution Cardiac Positron Emission Tomography/Computed Tomography for Small Animals

Here, we present an experimental imaging protocol for the quantification of cardiac function and morphology using high-resolution positron emission tomography/computed tomography for small animals. Both mice and rats are considered, discussing the different requirements of computed tomography contrast agents for the two...

retrograde perfusion and filling of mouse coronary vasculature as preparation for micro computed tomography imaging

Retrograde Perfusion and Filling of Mouse Coronary Vasculature as Preparation for Micro Computed Tomography Imaging

Visualization of the coronary vessels is critical to advancing our understanding of cardiovascular diseases. Here we describe a method for perfusing murine coronary vasculature with a radiopaque silicone rubber (Microfil), in preparation for micro-Computed Tomography (&mu;CT)...

long-term culture of human breast cancer specimens and their analysis using optical projection tomography

Long-term Culture of Human Breast Cancer Specimens and Their Analysis Using Optical Projection Tomography

We have developed a collagen-based in vitro assay which promotes proliferation and invasion from samples of all breast cancer subtypes. Optical Projection Tomography, a three dimensional microscopy technique was utilised to visualise and quantify tumour expansion. This assay may be used to quantify drug response of individual tumour...

use of micro x-ray computed tomography with phosphotungstic acid preparation to visualize human fibromuscular tissue

Use of Micro X-ray Computed Tomography with Phosphotungstic Acid Preparation to Visualize Human Fibromuscular Tissue

Micro X-ray computed tomography is effective in obtaining three-dimensional information from undamaged human specimens but has limited success in observing soft tissues. The use of phosphotungstic acid contrast agent can resolve this issue. We implemented this contrast agent to examine human delicate fibromuscular tissues (the orbicularis retaining...

osmotic drug delivery to ischemic hindlimbs and perfusion of vasculature with microfil for micro-computed tomography imaging

Osmotic Drug Delivery to Ischemic Hindlimbs and Perfusion of Vasculature with Microfil for Micro-Computed Tomography Imaging

We show here the in vivo insertion of an osmotic pump for constant local drug delivery and the creation of hindlimb ischemia in a mouse model. Moreover, the hindlimb vasculature is perfused with Microfil, a silicone radiopaque agent, to prepare for micro-computed tomography (micro-CT)...

assessment of bone fracture healing using micro-computed tomography

Assessment of Bone Fracture Healing Using Micro-Computed Tomography

Micro-computed tomography (&#181;CT) is a non-destructive imaging tool that is instrumental in assessing bone structure in preclinical studies, however there is a lack of consensus on &#181;CT procedures for analyzing the bone healing callus. This study provides a step-by-step &#181;CT protocol that allows the monitoring of fracture healing.

using high resolution computed tomography to visualize the three dimensional structure and function of plant vasculature

Using High Resolution Computed Tomography to Visualize the Three Dimensional Structure and Function of Plant Vasculature

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique that can be used to study the structure and function of plant vasculature in 3D. We demonstrate how HRCT facilitates exploration of xylem networks across a wide range of plant tissues and...

assessment of viability of human fat injection into nude mice with micro-computed tomography

Assessment of Viability of Human Fat Injection into Nude Mice with Micro-Computed Tomography

Fat grafting is an essential technique for reconstructing soft tissue deficits. However, it remains an unpredictable procedure characterized by variable graft survival.  Our goal was to devise a mouse model that utilizes a novel imaging method to compare volume retention between differing techniques of fat graft preparation and...

quantification of atherosclerotic plaque activity and vascular inflammation using [18-f] fluorodeoxyglucose positron emission tomography/computed tomography (fdg-pet/ct)

Quantification of Atherosclerotic Plaque Activity and Vascular Inflammation using [18-F] Fluorodeoxyglucose Positron Emission Tomography/Computed Tomography FDG-PET/CT

There is great need to identify atherosclerosis non-invasively, and here we demonstrate how FDG-PET/CT can be used to detect and quantify atherosclerotic plaque activity and vascular...

Quantification of Atherosclerotic Plaque Activity and Vascular Inflammation using [18-F] Fluorodeoxyglucose Positron Emission Tomography/Computed Tomography (FDG-PET/CT)

three-dimensional cephalometric landmark annotation demonstration on human cone beam computed tomography scans

Author Spotlight: Three-Dimensional Cephalometric Landmark Annotation Demonstration on Human Cone Beam Computed Tomography Scans  

Presented here is a detailed protocol for the conduction of three-dimensional cephalometric analysis with the use of human cone beam computed tomography...

3D Cephalometric Landmark Annotation Demonstration on Human CBCT Scans

cardiac graft revival and left ventricular loading in the langendorff perfusion system

Cardiac Graft Revival and Left Ventricular Loading in the Langendorff Perfusion System

continuous blood sampling in small animal positron emission tomography/computed tomography enables the measurement of the arterial input function

Continuous Blood Sampling in Small Animal Positron Emission Tomography/Computed Tomography Enables the Measurement of the Arterial Input Function

Here a protocol for continuous blood sampling during PET/CT imaging of rats to measure the arterial input function (AIF) is described. The catheterization, the calibration and setup of the system and the data analysis of the blood radioactivity are demonstrated. The generated data provide input parameters for subsequent bio-kinetic...

multi-tracer studies of brain oxygen and glucose metabolism using a time-of-flight positron emission tomography-computed tomography scanner

Author Spotlight: Enhancing the Understanding of Human Brain Metabolism In Vivo Using Positron Emission Tomography

Quantitative measurements of oxygen and glucose metabolism by PET are established technologies, but details of practical protocols are sparsely described in the literature. This paper presents a practical protocol successfully implemented on a state-of-the-art positron emission tomography-computed tomography...

Multi-Tracer Studies of Brain Oxygen and Glucose Metabolism Using a Time-of-Flight Positron Emission Tomography-Computed Tomography Scanner

computed tomography-guided time-domain diffuse fluorescence tomography in small animals for localization of cancer biomarkers

Computed Tomography-guided Time-domain Diffuse Fluorescence Tomography in Small Animals for Localization of Cancer Biomarkers

Diffuse fluorescence tomography offers a relatively low-cost and potentially high-throughout approach to preclinical in vivo tumor imaging. The methodology of optical data collection, calibration, and image reconstruction is presented for a computed tomography-guided non-contact time-domain system using fluorescent targeting of the tumor biomarker epidermal growth factor receptor in a mouse glioma...

3d imaging of soft-tissue samples using an x-ray specific staining method and nanoscopic computed tomography

3D Imaging of Soft-Tissue Samples using an X-ray Specific Staining Method and Nanoscopic Computed Tomography

A protocol for 3D visualization of microscopic tissue structures by using an X-ray specific staining method designed for X-ray computed tomography is...

non-invasive skeletal muscle quantification in small animals using micro-computed tomography

This protocol uses micro-computed tomography to enable the cost-effective quantification of lean mass, including skeletal muscle and visceral tissue, adipose tissue, and skeletal tissue in small animals. It distinguishes between lean and adipose tissue, which offers significant advantages for biomedical research, particularly in translational research in small...

Non-invasive Skeletal Muscle Quantification in Small Animals Using Micro-computed Tomography

Bacterial Detection &amp; Identification Using Electrochemical Sensors

Electrochemical sensors are widely used for rapid and accurate measurement of blood glucose and can be adapted for detection of a wide variety of analytes. Electrochemical sensors operate by transducing a biological recognition event into a useful electrical signal. Signal transduction occurs by coupling the activity of a redox enzyme to an amperometric electrode. Sensor specificity is either an inherent characteristic of the enzyme, glucose oxidase in the case of a glucose sensor, or a product of linkage between the enzyme and an antibody or probe.
Here, we describe an electrochemical sensor assay method to directly detect and identify bacteria. In every case, the probes described here are DNA oligonucleotides. This method is based on sandwich hybridization of capture and detector probes with target ribosomal RNA (rRNA). The capture probe is anchored to the sensor surface, while the detector probe is linked to horseradish peroxidase (HRP). When a substrate such as 3,3',5,5'-tetramethylbenzidine (TMB) is added to an electrode with capture-target-detector complexes bound to its surface, the substrate is oxidized by HRP and reduced by the working electrode. This redox cycle results in shuttling of electrons by the substrate from the electrode to HRP, producing current flow in the electrode.

We describe an electrochemical sensor assay method for rapid bacterial detection and identification. The assay involves a sensor array functionalized with DNA oligonucleotide capture probes for ribosomal RNA (rRNA) species-specific sequences. Sandwich hybridization of target rRNA with the capture probe and a horseradish peroxidase-linked DNA oligonucleotide detector probe produces a measurable amperometric current.

Electrochemical  sensors are widely used for rapid and accurate measurement of blood glucose and  can be adapted for detection of a wide variety of ...

Culturing Mouse Cardiac Valves in the Miniature Tissue Culture System

Heart valve disease is a major burden in the Western world and no effective treatment is available. This is mainly due to a lack of knowledge of the molecular, cellular and mechanical mechanisms underlying the maintenance and/or loss of the valvular structure. 
Current models used to study valvular biology include in vitro cultures of valvular endothelial and interstitial cells. Although, in vitro culturing models provide both cellular and molecular mechanisms, the mechanisms involved in the 3D-organization of the valve remain unclear. While in vivo models have provided insight into the molecular mechanisms underlying valvular development, insight into adult valvular biology is still elusive. 
In order to be able to study the regulation of the valvular 3D-organization on tissue, cellular and molecular levels, we have developed the Miniature Tissue Culture System. In this ex vivo flow model the mitral or the aortic valve is cultured in its natural position in the heart. The natural configuration and composition of the leaflet are maintained allowing the most natural response of the valvular cells to stimuli. The valves remain viable and are responsive to changing environmental conditions. This MTCS may provide advantages on studying questions including but not limited to, how does the 3D organization affect valvular biology, what factors affect 3D organization of the valve, and which network of signaling pathways regulates the 3D organization of the valve.

Here, we present an ex vivo flow model in which murine cardiac valves can be cultured allowing the study of the biology of the valve.

Heart valve disease is a major burden in the Western world and no effective treatment is available. This is mainly due to a lack of knowledge of the ...

Studying Protein Function and the Role of Altered Protein Expression by Antibody Interference and Three-dimensional Reconstructions

A strict management of protein expression is not only essential to every organism alive, but also an important strategy to investigate protein functions in cellular models. Therefore, recent research invented different tools to target protein expression in mammalian cell lines or even animal models, including RNA and antibody interference. While the first strategy has gathered much attention during the past two decades, peptides &#160;mediating a translocation of antibody cargos across cellular membranes and into cells, obtained much less interest. In this publication, we provide a detailed protocol how to utilize a peptide carrier named Chariot in human embryonic kidney cells as well as in primary hippocampal neurons to perform antibody interference experiments and further illustrate the application of three-dimensional reconstructions in analyzing protein function. Our findings suggest that Chariot is, probably due to its nuclear localization signal, particularly well-suited to target proteins residing in the soma and the nucleus. Remarkably, when applying Chariot to primary hippocampal cultures, the reagent turned out to be surprisingly well accepted by dissociated neurons.

Controlling protein expression is not only essential to every organism alive, but also an important strategy to investigate protein functions in cellular models. The protocol presented shows the application of antibody interference in mammalian cells including primary hippocampal neurons and demonstrates the use of three-dimensional reconstructions in studying protein function.

A strict management of protein expression is not only essential to every organism alive, but also an important strategy to investigate protein functions ...

Construction of Defined Human Engineered Cardiac Tissues to Study Mechanisms of Cardiac Cell Therapy

Human cardiac tissue engineering can fundamentally impact therapeutic discovery through the development of new species-specific screening systems that replicate the biofidelity of three-dimensional native human myocardium, while also enabling a controlled level of biological complexity, and allowing non-destructive longitudinal monitoring of tissue contractile function. Initially, human engineered cardiac tissues (hECT) were created using the entire cell population obtained from directed differentiation of human pluripotent stem cells, which typically yielded less than 50% cardiomyocytes. However, to create reliable predictive models of human myocardium, and to elucidate mechanisms of heterocellular interaction, it is essential to accurately control the biological composition in engineered tissues. 
To address this limitation, we utilize live cell sorting for the cardiac surface marker SIRP&#945; and the fibroblast marker CD90 to create tissues containing a 3:1 ratio of these cell types, respectively, that are then mixed together and added to a collagen-based matrix solution. Resulting hECTs are, thus, completely defined in both their cellular and extracellular matrix composition.
Here we describe the construction of defined hECTs as a model system to understand mechanisms of cell-cell interactions in cell therapies, using an example of human bone marrow-derived mesenchymal stem cells (hMSC) that are currently being used in human clinical trials. The defined tissue composition is imperative to understand how the hMSCs may be interacting with the endogenous cardiac cell types to enhance tissue function. A bioreactor system is also described that simultaneously cultures six hECTs in parallel, permitting more efficient use of the cells after sorting.

This manuscript describes the creation of defined engineered cardiac tissues using surface marker expression and cell sorting. The defined tissues can then be used in a multi-tissue bioreactor to investigate mechanisms of cardiac cell therapy in order to provide a functional, yet controlled, model system of the human heart.

Human cardiac tissue engineering can fundamentally impact therapeutic discovery through the development of new species-specific screening systems that ...

The use of Micro-Computed Tomography (MicroCT) for in vivo studies of small animals as models of human disease has risen tremendously due to the fact that MicroCT provides quantitative high-resolution three-dimensional (3D) anatomical data non-destructively and longitudinally. Most importantly, with the development of a novel preclinical iodinated contrast agent called eXIA160, functional and metabolic assessment of the heart became possible. However, prior to the advent of commercial MicroCT scanners equipped with X-ray flat-panel detector technology and easy-to-use cardio-respiratory gating, preclinical studies of cardiovascular disease (CVD) in small animals required a MicroCT technologist with advanced skills, and thus were impractical for widespread implementation. The goal of this work is to provide a practical guide to the use of the high-speed Quantum FX MicroCT system for comprehensive determination of myocardial global and regional function along with assessment of myocardial perfusion, metabolism and viability in healthy mice and in a cardiac ischemia mouse model induced by permanent occlusion of the left anterior descending coronary artery (LAD).

This method outlines the use of Quantum Micro-Computed Tomography (MicroCT) to assess cardiac morphology, function, perfusion, metabolism and viability with iodinated contrast agent in mice with experimentally-induced myocardial ischemia. The technique can be applied for non-destructive high-throughput longitudinal in vivo imaging of various animal models of human heart disease.

The use of Micro-Computed Tomography (MicroCT) for in vivo studies of small animals as models of human disease has risen tremendously due to the fact that ...

Using Extraordinary Optical Transmission to Quantify Cardiac Biomarkers in Human Serum

For a biosensing platform to have clinical relevance in point-of-care (POC) settings, assay sensitivity, reproducibility, and ability to reliably monitor analytes against the background of human serum are crucial.
Nanoimprinting lithography (NIL) was used to fabricate, at a low cost, sensing areas as large as 1.5 mm x 1.5 mm. The sensing surface was made of high-fidelity arrays of nanoholes, each with an area of about 140 nm2. The great reproducibility of NIL made it possible to employ a one-chip, one-measurement strategy on 12 individually manufactured surfaces, with minimal chip-to-chip variation. These nanoimprinted localized surface plasmon resonance (LSPR) chips were extensively tested on their ability to reliably measure a bioanalyte at concentrations varying from 2.5 to 75 ng/mL amidst the background of a complex biofluid-in this case, human serum. The high fidelity of NIL enables the generation of large sensing areas, which in turn eliminates the need for a microscope, as this biosensor can be easily interfaced with a commonly available laboratory light source. These biosensors can detect cardiac troponin in serum with a high sensitivity, at a limit of detection (LOD) of 0.55 ng/mL, which is clinically relevant. They also show low chip-to-chip variance (due to the high quality of the fabrication process). The results are commensurable with widely used enzyme-linked immunosorbent assay (ELISA)-based assays, but the technique retains the advantages of an LSPR-based sensing platform (i.e., amenability to miniaturization and multiplexing, making it more feasible for POC applications).

This work describes a nanoimprinting lithography method to fabricate high-quality sensing arrays that work on the principle of extraordinary optical transmission. The biosensor is low-cost, robust, easy to use, and can detect cardiac troponin I in serum at clinically relevant concentrations (99th percentile cutoff &#8764;10-400 pg/mL, depending on the assay).

For a biosensing platform to have clinical relevance in point-of-care (POC) settings, assay sensitivity, reproducibility, and ability to reliably monitor ...

Efficient Generation and Editing of Feeder-free IPSCs from Human Pancreatic Cells Using the CRISPR-Cas9 System

Embryonic and induced pluripotent stem cells can self-renew and differentiate into multiple cell types of the body. The pluripotent cells are thus coveted for research in regenerative medicine and are currently in clinical trials for eye diseases, diabetes, heart diseases, and other disorders. The potential to differentiate into specialized cell types coupled with the recent advances in genome editing technologies including the CRISPR/Cas system have provided additional opportunities for tailoring the genome of iPSC for varied applications including disease modeling, gene therapy, and biasing pathways of differentiation, to name a few. Among the available editing technologies, the CRISPR/Cas9 from Streptococcus pyogenes has emerged as a tool of choice for site-specific editing of the eukaryotic genome. The CRISPRs are easily accessible, inexpensive, and highly efficient in engineering targeted edits. The system requires a Cas9 nuclease and a guide sequence (20-mer) specific to the genomic target abutting a 3-nucleotide &#34;NGG&#34; protospacer-adjacent-motif (PAM) for targeting Cas9 to the desired genomic locus, alongside a universal Cas9 binding tracer RNA (together called single guide RNA or sgRNA). Here we present a step-by-step protocol for efficient generation of feeder-independent and footprint-free iPSC and describe methodologies for genome editing of iPSC using the Cas9 ribonucleoprotein (RNP) complexes. The genome editing protocol is effective and can be easily multiplexed by pre-complexing sgRNAs for more than one target with the Cas9 protein and simultaneously delivering into the cells. Finally, we describe a simplified approach for identification and characterization of iPSCs with desired edits. Taken together, the outlined strategies are expected to streamline generation and editing of iPSC for manifold applications.

This protocol describes in detail the generation of footprint-free induced pluripotent stem cells (iPSCs) from human pancreatic cells in feeder-free conditions, followed by editing using CRISPR/Cas9 ribonucleoproteins and characterization of the modified single-cell clones.

Embryonic and induced pluripotent stem cells can self-renew and differentiate into multiple cell types of the body. The pluripotent cells are thus coveted ...

A Net Mold-based Method of Scaffold-free Three-Dimensional Cardiac Tissue Creation

This protocol describes a novel and easy net mold-based method to create three-dimensional (3-D) cardiac tissues without additional scaffold material. Human-induced pluripotent stem-cell-derived cardiomyocytes (iPSC-CMs), human cardiac fibroblasts (HCFs), and human umbilical vein endothelial cells (HUVECs) are isolated and used to generate a cell suspension with 70% iPSC-CMs, 15% HCFs, and 15% HUVECs. They are co-cultured in an ultra-low attachment "hanging drop" system, which contains micropores for condensing hundreds of spheroids at one time. The cells aggregate and spontaneously form beating spheroids after 3 days of co-culture. The spheroids are harvested, seeded into a novel mold cavity, and cultured on a shaker in the incubator. The spheroids become a mature functional tissue approximately 7 days after seeding. The resultant multilayered tissues consist of fused spheroids with satisfactory structural integrity and synchronous beating behavior. This new method has promising potential as a reproducible and cost-effective method to create engineered tissues for the treatment of heart failure in the future.

This protocol describes a net mold-based method to create three-dimensional scaffold-free cardiac tissues with satisfactory structural integrity and synchronous beating behavior.

This protocol describes a novel and easy net mold-based method to create three-dimensional (3-D) cardiac tissues without additional scaffold material. ...

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in every tissue to be identified and characterized. Our laboratory is actively working to make technological advances in X-ray micro-computed tomography (micro-CT) that will bring the diagnostic power of histology to the study of full tissue volumes at cellular resolution (i.e., an X-ray Histo-tomography modality). Toward this end, we have made targeted improvements to the sample preparation pipeline. One key optimization, and the focus of the present work, is a straightforward method for rigid embedding of fixed and stained millimeter-scale samples. Many of the published methods for sample immobilization and correlative micro-CT imaging rely on placing the samples in paraffin wax, agarose, or liquids such as alcohol. Our approach extends this work with custom procedures and the design of a 3-dimensional printable apparatus to embed the samples in an acrylic resin directly into polyimide tubing, which is relatively transparent to X-rays. Herein, sample preparation procedures are described for the samples from 0.5 to 10 mm in diameter, which would be suitable for whole zebrafish larvae and juveniles, or other animals and tissue samples of similar dimensions. As proof of concept, we have embedded the specimens from Danio, Drosophila, Daphnia, and a mouse embryo; representative images from 3-dimensional scans for three of these samples are shown. Importantly, our methodology leads to multiple benefits including rigid immobilization, long-term preservation of laboriously-created resources, and the ability to re-interrogate samples.

We developed protocols and designed a custom apparatus to enable embedding of millimeter-scale specimens. We present sample preparation procedures with an emphasis on embedding in acrylic resin and polyimide tubing to achieve rigid immobilization and long-term storage of specimens for the interrogation of tissue architecture and cell morphology by micro-CT.

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in ...

Intra-cardiac Side-Firing Light Catheter for Monitoring Cellular Metabolism using Transmural Absorbance Spectroscopy of Perfused Mammalian Hearts

Absorbance spectroscopy of cardiac muscle provides non-destructive assessment of cytosolic and mitochondrial oxygenation via myoglobin and cytochrome absorbance respectively. In addition, numerous aspects of the mitochondrial metabolic status such as membrane potential and substrate entry can also be estimated. To perform cardiac wall transmission optical spectroscopy, a commercially available side-firing optical fiber catheter is placed in the left ventricle of the isolated perfused heart as a light source. Light passing through the heart wall is collected with an external optical fiber to perform optical spectroscopy of the heart in near real- time. The transmission approach avoids numerous surface scattering interference occurring in widely used reflection approaches. Changes in transmural absorbance spectra were deconvolved using a library of chromophore reference spectra, providing quantitative measures of all the known cardiac chromophores simultaneously. This spectral deconvolution approach eliminated intrinsic errors that may result from using common dual wavelength methods applied to overlapping absorbance spectra, as well as provided a quantitative evaluation of the goodness of fit. A custom program was designed for data acquisition and analysis, which permitted the investigator to monitor the metabolic state of the preparation during the experiment. These relatively simple additions to the standard heart perfusion system provide a unique insight into the metabolic state of the heart wall in addition to conventional measures of contraction, perfusion, and substrate/oxygen extraction.

Here we introduce a method for using an intra-ventricle optical catheter in perfused hearts to perform absorbance spectroscopy across the heart wall. The data obtained provides robust information on tissue oxygen tension as well as substrate utilization and membrane potential simultaneously with cardiac performance measures in this ubiquitous preparation.

Absorbance spectroscopy of cardiac muscle provides non-destructive assessment of cytosolic and mitochondrial oxygenation via myoglobin and cytochrome ...