Real-time Electrophysiology: Using Closed-loop Protocols to Probe Neuronal Dynamics and Beyond

Podsumowanie

Closed-loop protocols are becoming increasingly widespread in modern day electrophysiology. We present a simple, versatile and inexpensive way to perform complex electrophysiological protocols in cortical pyramidal neurons in vitro, using a desktop computer and a digital acquisition board.

Streszczenie

Experimental neuroscience is witnessing an increased interest in the development and application of novel and often complex, closed-loop protocols, where the stimulus applied depends in real-time on the response of the system. Recent applications range from the implementation of virtual reality systems for studying motor responses both in mice¹ and in zebrafish², to control of seizures following cortical stroke using optogenetics³. A key advantage of closed-loop techniques resides in the capability of probing higher dimensional properties that are not directly accessible or that depend on multiple variables, such as neuronal excitability⁴ and reliability, while at the same time maximizing the experimental throughput. In this contribution and in the context of cellular electrophysiology, we describe how to apply a variety of closed-loop protocols to the study of the response properties of pyramidal cortical neurons, recorded intracellularly with the patch clamp technique in acute brain slices from the somatosensory cortex of juvenile rats. As no commercially available or open source software provides all the features required for efficiently performing the experiments described here, a new software toolbox called LCG⁵ was developed, whose modular structure maximizes reuse of computer code and facilitates the implementation of novel experimental paradigms. Stimulation waveforms are specified using a compact meta-description and full experimental protocols are described in text-based configuration files. Additionally, LCG has a command-line interface that is suited for repetition of trials and automation of experimental protocols.

Wprowadzenie

In recent years, cellular electrophysiology has evolved from the traditional open-loop paradigm employed in voltage and current clamp experiments to modern closed-loop protocols. The best known closed-loop technique is perhaps the dynamic clamp^6,7, which enabled the synthetic injection of artificial voltage-gated ion channels to determine the neuronal membrane voltage⁸, the in-depth study of the effects of non-deterministic flickering on ion channels on neuronal response dynamics⁹, as well as the recreation in vitro of realistic in vivo-like synaptic background activity¹⁰.

Other closed-loop paradigms that have been proposed include the reactive clamp¹¹, to study in vitro the generation of self-sustained persistent activity, and the response clamp^4,12, to investigate the cellular mechanisms underlying neuronal excitability.

Here we describe a powerful framework that allows applying a variety of closed-loop electrophysiological protocols in the context of whole-cell patch clamp recordings performed in acute brain slices. We show how to record somatic membrane voltage by means of patch clamp recordings in pyramidal neurons from the somatosensory cortex of juvenile rats and apply three different closed-loop protocols using LCG, a command-line-based software toolbox developed in the laboratory of Theoretical Neurobiology and Neuroengineering.

Briefly, the described protocols are, first the automated injection of a series of current clamp stimulus waveforms, relevant for the characterization of a large set of active and passive membrane properties. These have been suggested to capture the electrophysiological phenotype of a cell in terms of its response properties to a stereotyped series of stimulus waveforms. Known as the e-code of a cell (e.g., see ^13,14), such a collection of electrical responses is used by several laboratories to objectively classify neurons on the basis of their electrical properties. This includes the analysis of the stationary input-output transfer relationship (f-I curve), by an innovative technique that involves the closed-loop, real-time control of the rate of firing by means of a proportional-integral-derivative (PID) controller, second the recreation of realistic in vivo-like background synaptic activity in in vitro preparations¹⁰ and , third the artificial connection in real-time of two simultaneously recorded pyramidal neurons by means of a virtual GABAergic interneuron, which is simulated by the computer.

Additionally, LCG implements the technique known as Active Electrode Compensation (AEC)¹⁵, which allows implementing dynamic clamp protocols using a single electrode. This allows compensating undesired effects (artifacts) of the recording electrode that arise when it is used for delivering intracellular stimuli. The method is based on a non-parametric estimate of the equivalent electrical properties of the recording circuit.

The techniques and experimental protocols described in this paper can be readily applied in conventional open-loop voltage and current clamp experiments and can be extended to other preparations, such as extracellular^4,16 or intracellular recordings in vivo^17,18. The careful assembly of the setup for whole cell patch clamp electrophysiology is a very important step for stable, high quality recordings. In the following we assume that such an experimental setup is already available to the experimenter, and focus our attention on describing the usage of LCG. The reader is pointed to ^19–22 for additional tips about optimization and debugging.

Protokół

The protocol described here complies with the recommendations and guidelines of the Ethics Committee of the Department of Biomedical Sciences of the University of Antwerp. This protocol requires the preparation of non-sentient material from the explanted brain of juvenile Wistar rats, obtained by approved humane euthanasia techniques.

1. Equipment Preparation

1. Install and configure the data acquisition and stimulation system.
   1. Use a personal computer (PC) equipped with a data acquisition (DAQ) card supported by Comedi to record signals and send analog control voltages to the electrophysiological amplifier.
      NOTE: Comedi is a Linux module and library that supports a multitude of DAQ cards from the most common manufacturers: visit http://www.comedi.org for more information.
   2. In case a computer-controlled patch clamp amplifier is in use, employ a second PC besides the one dedicated to the amplifier control.
      NOTE: While the latter may run a conventional operating system, the extra PC will be operating in real-time by means of a special operating system. Under these conditions, it is convenient to use a single monitor, mouse, and keyboard attached to the extra PC, while connecting by a remote desktop application to the dedicated PC.
   3. Download the ISO image of the Live CD containing a real-time Linux operating system with LCG preinstalled from http://www.tnb.ua.ac.be/software/LCG_Live_CD.iso and burn it on a blank CD or USB stick”.
   4. Simply insert the CD into the drive of the PC containing the DAQ card and start it. Alternatively, install LCG from its online source repository on a PC running the Linux operating system (e.g., Debian or Ubuntu). Consult the online manual for details on the installation procedure. The manual is available online at http://danielelinaro.github.io/dynclamp/lcg_manual.pdf.
   5. Boot from the live CD: this will automatically load a fully configured system. To do this, place the LCG Live CD in the computer CD-ROM drive and boot the computer from CD; select the real-time kernel (default option) as soon as the boot menu appears and wait for the system to initialize.
   6. Calibrate the DAQ card by typing at the command prompt:
      sudo comedi_calibrate
      or
      sudo comedi_soft_calibrate
      depending on whether the data-acquisition board supports hardware or software calibration, respectively (use the command sudo comedi_board_info to obtain information on the board).
   7. Set the appropriate analog-to-digital and digital-to-analog conversion factors: this requires having access to the manual of the cellular electrophysiological amplifier, and particularly to its specifications on its conversion factors.
   8. Use a text editor to specify the appropriate numerical values in the file /home/user/.lcg-env, for the environment variables AI_CONVERSION_FACTOR_CC, AI_CONVERSION_FACTOR_VC, AO_CONVERSION_FACTOR_CC, AO_CONVERSION_FACTOR_VC.
      NOTE: These represent the input (AI) and output (AO) gains for current clamp (CC) and voltage clamp (VC) modes, and the conversion factors between the voltage commands provided by the computer and the current or voltages generated by the amplifier, respectively.
   9. Alternatively, use the LCG script provided (lcg-find-conversion-factors), to find the conversion factors of his or her system.
      NOTE: The values computed by lcg-find-conversion-factors are guesses, which in some cases are required to be numerically truncated or rounded to reflect the exact values of the conversion factors.
   10. To use lcg-find-conversion-factors, start by connecting the 'model cell' that often is purchased with the amplifier to the corresponding headstage. Then, open a terminal on the Linux machine where you are running the Live CD and enter the following command at the shell prompt:
       lcg-find-conversion-factors -i $HOME/.lcg-env -o $HOME/.lcg-env 
       NOTE: In both cases (i.e., manual modification of /home/user/.lcg-env or usage of lcg-find-conversion-factors), close and open the terminal for the changes to take effect.
   11. If multiple headstages are used, set the conversion factors to the same values in all channels; if that is not possible, consult the LCG online manual to understand how to use multiple conversion factors in lcg-stimulus or how to produce configuration files that better suit the user’s needs.

2. Preparation of Acute Brain Slices from the Somatosensory Cortex

1. Preparation of solutions for electrophysiology.
   1. Prepare Artificial Cerebro-Spinal Fluid (ACSF) by mixing (in mM) 125 NaCl, 2.5 KCl, 1.25 NaH₂PO₄, 26 NaHCO₃, 25 glucose, 2 CaCl₂, and 1 MgCl₂. Prepare 10x stock solutions to reduce the preparation time on the day of the experiment. Prepare 2 L, of which one will be used for the preparation of the slices and the other for recording.
   2. Saturate the ACSF with 95% O₂ and 5% CO₂ for at least 30 min prior to the beginning of the procedure.
   3. For current clamp recordings, use an intracellular solution (ICS) containing (in mM) 115 K-gluconate, 20 KCl, 10 HEPES, 4 ATP-Mg, 0.3 Na₂-GTP, 10 Na₂-phosphocreatine. Prepare the solution in ice and filter it prior to the beginning of the recordings to eliminate the risk of clogging the pipette.
2. Brain extraction.
   1. Anesthetize the animal placing the animal in an induction chamber with 4% Isoflurane and rapidly decapitate it using a guillotine or large scissors.
   2. Cut the skin along the midline and slide it to the ears.
   3. Using a fine pair of scissors cut the skull along the midline. Keep the blade as close as possible to the surface so as to minimize damage to the underlying brain. Open the skull with a pair of tweezers, use a spatula to sever the optic nerve and the brainstem and gently drop the brain in ice-cold ACSF.
   4. Separate the cerebellum and the two hemispheres with a scalpel (blade 24).
   5. Remove excess water from one of the two hemispheres and glue it on an inclined platform using a drop of superglue. Quickly add a few drops of ACSF over the brain and transfer it to the vibratome chamber.
      NOTE: When preparing sagittal slices, the angle of the platform is important to avoid damaging the dendrites of pyramidal cells during the slicing procedure.
3. Preparation of the slices.
   1. Position the blade over the brain and discard the first 2.5 - 3 mm. Adjust the speed and frequency to limit damage to the surface of the slice while at the same time minimizing the time required for the slicing procedure.
   2. Set the thickness to 300 µm and begin slicing. Once the blade has gone past the cortex, use a razor blade or a bent needle to cut above the hippocampus and at the edges of the cortical area of interest.
   3. Place the slices in a multi-well incubation chamber kept at 32 - 34 °C.
   4. Retract the blade and repeat points 2.3.2 and 2.3.3 until 5 - 8 slices are cut. The best slices are usually the ones where the blood vessels are parallel to the surface.
   5. Incubate the slices for 30 min after the last slice is placed in the chamber.

3. Patch-clamp Recordings from Layer 5 Pyramidal Neurons

1. Place a slice in the recording chamber and search for healthy cells. These cells usually have lower contrast, a smooth appearance and are not swollen.
2. Inspect the slice under the microscope with the 40X magnification lens and search for cells in layer 5, located approximately 600 to 1,000 µm from the surface of the brain.
3. Once a suitable cell is found, load one third of the micropipette with ICS and place it in the headstage.
4. On the personal computer running the live CD or the pre-configured Linux operating system, launch a command shell (e.g., bash) and at its prompt type the command lcg-zero. This ensures that the DAQ board is not driving the amplifier.
5. Apply 30 - 50 mbar of positive pressure by pressing on the piston of a common syringe, connected by tubing to the pipette holder and, with the help of the microscope, place the pipette approximately 100 µm above the slice.
   NOTE: Place the pipette in a position that allows a direct route to the target cell, preferably using the approach mode of the micromanipulator.
6. Acting on the controls the electrophysiology amplifier, adjust the pipette offset and output a test pulse (10 mV) in voltage clamp mode.
7. Reduce the pressure to 10 - 30 mbar (depending on the pipette size) by withdrawing the piston of the syringe; gently approach the cell and check for the formation of a dimple by observing the image on the video camera monitor. Monitor the test pulse for an increase in resistance at all times, by watching the current waveform displayed on the oscilloscope connected to the electrophysiology amplifier (alternatively you can use the command lcg-seal-test to monitor the pipette resistance).
8. Release the pressure and if necessary apply gentle negative pressure to the pipette to help seal formation when you notice an increase in pipette resistance and the formation of a 'dimple' on the cell.
9. While the seal forms, gradually decrease the holding potential to -70 mV.
10. Once a gigaohm seal has been obtained, ensure that the holding current is between 0 - 30 pA. Apply short pulses of negative pressure (suction) to break the membrane and establish the whole-cell configuration. Alternatively, you can inject strong and brief pulses of voltage (i.e., using the 'ZAP' command on the amplifier or holding the cell at very negative) to rupture the membrane, depending on the preparation and glass pipette used.
11. Switch to current clamp mode and verify that the resting membrane potential is typical of a healthy cell. For cortical pyramidal neurons using a potassium-gluconate-based solution, this value is usually between -65 and -75 mV.

4. Semi-automatic Characterization of a Neuron’s Electrical Response Properties

1. Create a directory to store user’s data. In order to do this the employ a script included in the LCG live CD that creates folders based on the date. To use it, type at the command prompt
   cd ~/experiments
   lcg-create-experiment-folder -s psp,in_vivo_like
   This will create a folder where the data for that cell will be saved (and a 'psp' and 'in_vivo_like' subfolders) and it will print its name to the terminal window; it is also possible to store additional information such as pipette resistance and cell type using this script.
2. Change directory to the newly created folder using the command
   cd ~/<foldername>
   The folder name is the one displayed by the command lcg-create-experiment-folder and will have the timestamp of the current day (i.e., year-month-day), as in 20140331A01.
3. Make sure that the amplifier is set to operate in current clamp mode, that the cables are connected and the external voltage command of the amplifier, if present, is enabled.
4. Enter the command lcg-ecodeat the command prompt. This calls a series of commands (namely lcg-ap, lcg-vi, lcg-ramp, lcg-tau and lcg-steps), used to characterize basic response properties of the cell. lcg-ecode requires that the user specify two parameters: the amplitude of the 1 ms-long pulse of current used to elicit a single spike in the cell, and the maximum amplitude of the current ramp injected into the cell to find its rheobase.
   Use the following command syntax:
   lcg-ecode --pulse-amplitude X --ramp-amplitude Y
   with a choice of the values X and Y (in pA) that are sufficient to make the cell fire in response to a 1 ms-long pulse and a sustained injection of current, respectively.
   NOTE: These protocols require performing the numerical estimate of the 'electrode kernel' in order to use the Active Electrode Compensation (AEC)¹⁵. A noisy current injection is used to estimate the kernel and the user is prompted to confirm the number of samples that make up the kernel. See ¹⁵ for detailed information on the meaning of the electrode kernel and how to choose the number of kernel samples.

5. Injection of Conductance through Simulated Synapses and Simulation of In Vivo-like Background Activity

1. Injection of simulated excitatory post-synaptic potentials
   1. Change to the directory where you will save the next experiment, by typing the following command at the command prompt of the shell:
      cd psp/01
   2. Copy an LCG configuration file to the current directory and open it with a text editor (Nano in this example) by typing the following commands at the command prompt of the shell (this example configuration file is included in the source code and the live cd):
      cp ~/local/src/lcg/configurations/epsp.xml 
      nano epsp.xml
      NOTE: This is simply a text file with different entities connected to each other. For more details see the Representative Results section.
   3. If necessary edit the inputChannel, outputChannel, the inputConversionFactor and the outputConversionFactor in this file to match the user’s setup.
   4. Compute the electrode kernel needed to perform the active electrode compensation ' the method used by LCG to perform single electrode dynamic clamp ' by issuing the command
      lcg-kernel
      This will prompt for the number of points in the kernel. Again, select a number so that the electrode kernel covers the end of the exponential decay tail.
   5. Perform the dynamic clamp experiment using the command
      lcg-experiment -c epsp.xml
   6. List the files and visualize the results by using the command
      ls -l
      lcg-plot-file -f last
2. Injection of simulated inhibitory post-synaptic potentials
   1. Create a folder and copy the epsp.xml file to it by typing the following commands at the command prompt of the shell:
      mkdir ../02
      cp epsp.xml ../02/ipsp.xml
      cd ../02
   2. Edit the configuration file by using a text editor: change the synaptic reversal potential and rise and decay time constants of the model synapse Exp2Synapse to the following:
      parameters>
      <E>-80</E>
      <tauRise>0.8e-3</tauRise>
      <tauDecay>10e-3</tauDecay>
      <parameters>
      Quit the text editor.
   3. Compute the electrode kernel and perform the experiment as in 5.1, by typing the following commands at the command prompt of the shell:
      lcg-kernel
      lcg-experiment -c ipsp.xml
   4. List the files and visualize the results, by typing the following commands at the command prompt of the shell:
      ls -l
      lcg-plot-file -f <filename.h5>
3. Simulation of in vivo-like background activity:
   1. Change to the directory where you want to save the following experiment, as previously shown, by typing the following commands at the command prompt of the shell:
      cd ../../in_vivo_like/01
   2. Copy the configuration file from LCG source directory, by typing the following commands at the command prompt of the shell:
      cp ~/local/src/lcg/configurations/in_vivo_like.xml 
      nano in_vivo_like.xml
      NOTE: This file is simply the concatenation of the previous ones; two Poisson-point processes that generate spike trains, which in turn feed inhibitory and excitatory model synapses, generate the background activity.
   3. Adjust the DAQ configuration parameters for the user’s setup, as described in 5.1.3 and exit the editor.
   4. Compute the electrode kernel and perform the experiment as in 5.1, by typing the following commands at the command prompt of the shell:
      lcg-kernel
      lcg-experiment -c in_vivo_like.xml -n 10 -i 3
      The '-n 10' and '-i 3' switches indicate that the stimulation should be repeated 10 times at intervals of three sec.
   5. Visualize the raw traces by using the following command at the command prompt of the shell:
      lcg-plot-file -f all

Wyniki

In the previous sections, we have described how to use the software toolbox LCG to characterize the electrophysiological properties of L5 pyramidal cells and to recreate in vivo-like synaptic activity in a slice preparation. The use of a command-line interface and semi-automated protocol favor the reproducibility and efficiency of the experiment, which can have a large impact on the output and quality of the data produced. Additionally, since the data is saved in a consistent way, it is easy to extend the analys...

Dyskusje

In this text a full protocol for the implementation of real-time, closed-loop single cell electrophysiological experiments was described, using the patch clamp technique and a recently developed software toolbox called LCG. To optimize the quality of the recordings it is crucial that the recording setup be properly grounded, shielded and vibration free: this ensures stable and lasting whole-cell access to the cell, which, together with the possibility of automating entire sections of the stimulation protocols, allows for...

Materiały

Name	Company	Catalog Number	Comments
Tissue slicer	Leica	VT-1000S
Pipette puller	Sutter	P-97
Pipettes	WPI	1B150F-4	1.5/0.84 mm OD/ID, with filament
Vibration isolation table	TMC	20 Series
Microscope	Leica	DMLFS	40X Immersion Objective
Manipulators	Scientifica	PatchStar
Amplifiers	Axon Instruments	MultiClamp 700B	Computer controlled
Data acquisition card	National Instruments	PCI-6229	Supported by Comedi Linux Drivers
Desktop computer	Dell	Optiplex 7010 Tower	OS: real-time Linux
Oscilloscopes	Tektronix	TDS-1002
Perfusion Pump	Gibson	MINIPULS3	Used with R4 Pump head (F117606)
Temperature controller	Multichannel Systems	TC02	PH01 Perfusion Cannula
Manometer	Testo	510	Optional
Incubator	Memmert	WB14
NaCl	Sigma	71376	ACSF
KCl	Sigma	P9541	ACSF, ICS
NaH2PO4	Sigma	S3139	ACSF
NaHCO3	Sigma	S6014	ACSF
CaCl2	Sigma	C1016	ACSF
MgCl2	Sigma	M8266	ACSF
Glucose	Sigma	G7528	ACSF
K-Gluconate	Sigma	G4500	ICS
HEPES	Sigma	H3375	ICS
Mg-ATP	Sigma	A9187	ICS
Na2-GTP	Sigma	51120	ICS
Na2-Phosphocreatine	Sigma	P7936	ICS