The authors would like to thank G. Shambat, C. Phillips, K. Aghaei for invaluable discussions, F. Afshinmanesh for SEM images, T. Marvdashti for experimental support, and M.F. Churbanov and G.E. Snopatin from the Institute of Chemistry of High-Purity Substances and V.G. Plotnichenko and E.M. Dianov from the Fiber Optics Research Center of the Russian Academy of Sciences for providing the As2S3 fiber. We also are grateful for support from the Office of Naval Research, NASA, the Air Force Office of Scientific Research, Agilent, and the Joint Technologies Office.

1. Tapering Setup Fabrication (See Assembled Setup in Figure 1)
<ol>
	<li>Secure the motorized linear stages on the breadboard (roughly centered) so that the stages are in contact and will translate towards and away from one another</li>
	<li>Prepare and place the fiber mounts
	<ol>
		<li>Attach two optical posts to the motorized linear stage plates (one each) using the holes closest to each other.</li>
		<li>Attach the bare optical fiber mounts to the tops of the posts. Make sure that the v-grooves for the fiber are aligned. (Note: The height of the bare optical fiber mounts will roughly be the beam height of the system. Choose the future post and pedestal heights accordingly.)</li>
	</ol>
	</li>
	<li>Prepare and place the input and output coupling elements
	<ol>
		<li>Attach the linear translation stages to the motorized linear stages (one for the input and one for the output side) with the adapter plates.</li>
		<li>Place the AR coated ZnSe input coupling lens (mounted in an optical mount with x and y translation on a pedestal) on the input translation stage. Choose a focal length that gives optimal coupling from the pump source to the core of the fiber. Make sure the center of the lens is at the same height as the v-grooves of the fiber clamps.</li>
		<li>Place the uncoated ZnSe output coupling lens (mounted in an optical mount with x and y translation on a pedestal) on the output translation stage. Make sure the center of the lens is at the same height as the v-groove.</li>
	</ol>
	</li>
	<li>Prepare and place the heating element (as shown in Figure 2)
	<ol>
		<li>Machine the aluminum block to desired dimensions (~6 mm x 25.4 mm x 17.5 mm) with holes for the fiber (with a slit for inserting and removing the fiber) and for monitoring the fiber temperature, holes for the cartridge heaters, and 8/32 tapped holes on top and bottom for mounting and securing the cartridge heaters.</li>
		<li>Insert the cartridge heaters to the proper holes of the aluminum block and secure them with 8/32 set screws.</li>
		<li>Attach a ceramic post to the top 8/32 set screw for thermal isolation.</li>
		<li>Attach an optical post to the ceramic post and use a right angle post clamp with an additional optical post to secure the heater to the XYZ linear stage.</li>
		<li>Secure the XYZ linear stage to the breadboard so that the hole for the As2S3 fiber in the aluminum heater can be centered with the v-grooves of the fiber clamps.</li>
		<li>Translate the aluminum heater with the XYZ linear stage so that the heater is no longer near the bare optical fiber clamps, allowing the fiber to be secured without obstruction.</li>
	</ol>
	</li>
</ol>
2. Chalcogenide Fiber Preparation
<ol>
	<li>Soak a desired length of the jacketed As2S3 fiber (must be longer than 8.5 cm-the length of jacketed fiber needed for each fiber taper) in acetone for about 10 min or until the jacket becomes soft. (Use the appropriate solvent for the jacket if using a different fiber).</li>
	<li>Gently remove the softened jacket with a KimWipe, removing a section no longer than 5 cm at a time.</li>
	<li>Clean the bare fiber with isopropanol on a KimWipe.</li>
	<li>Use the beavertail cleaver to cleave one end of the As2S3 fiber. Image the discarded fiber tip to inspect cleave quality.</li>
	<li>Measure and break at least a 6.35-cm length piece of the fiber. This fiber length must be ~2 cm longer than the length needed for the fiber to barely stick out of the fiber clamps.</li>
	<li>Use the beavertail cleaver to cleave the second end of the fiber. Image the discarded fiber tip to inspect cleave quality. Avoid contact with the first cleaved end of fiber.</li>
	<li>Place the fiber in the fiber clamps of the tapering setup. Avoid touching the center of the fiber (where the fiber will be heated).</li>
</ol>
3. In-situ Fiber Tapering Procedure
<ol>
	<li>Couple the mid-IR pump source to the fundamental mode of the fiber with the AR coated ZnSe lens (f = 12.7 mm). Use the uncoated ZnSe lens (f = 20 mm) to image the output facet of the fiber with the Pyrocam to ensure the power is mostly in the fundamental mode. Make sure that the pump beam is propagating along the axis of the fiber. If it is not, the coupling will change once the motorized stages begin to move.</li>
	<li>
	<ol>
		<li>Place a chopper in front of the pump source. (This step is needed for AC coupled detectors).</li>
		<li>Couple the output of the fiber through the monochromator and to the InSb detector using the uncoated CaF2 lenses (f = 20 mm) before and after the monochromator.</li>
		<li>Rotate the grating of the monochromator to allow the long wavelength side of the spectrum to pass through the monochromator until the transmitted signal is barely above the noise floor (at ~3.9 &mu;m). Instead of filtering with the monochromator (steps 3.2.2 and 3.2.3), an appropriate optical filter can be used to measure the power in detectable wavelengths longer than the longest measureable wavelength content of the pump.</li>
	</ol>
	</li>
	<li>Translate the aluminum heater until the fiber slips through the slit and is centered in the aluminum heater's fiber hole.</li>
	<li>Place the RTD sensor level with one of the cartridge heaters. Gently press the RTD sensor against the aluminum heater so that it is fully in contact with the block as shown in Figure 2. If the RTD is not in contact with the heater correctly (or not in a repeatable fashion), the temperature of the block will be unknown and cause the fiber to break during tapering. Make sure that the signal to the monochromator has not decreased.
	<ol>
		<li>A small RTD can be placed inside the other hole of the heater block to monitor the temperature in the hole. (Optional)</li>
	</ol>
	</li>
	<li>Use the digital microscope to image the fiber in the heater block to allow for monitoring of the fiber during the tapering process. (Optional)</li>
	<li>Cover the setup with a box (with holes for the input and output beams) to reduce airflow and allow for stable tapering temperature.</li>
	<li>With the RTD and cartridge heaters connected, turn on the temperature controller. Set the temperature to ~200 &deg;C, where the fiber begins to soften (the exact temperature will depend on the dimensions of the heater, the environment temperature, and air flow around the fiber).</li>
	<li>Once the temperature is stable around the set point, start the Labview program that translates the motorized stages away from one another at ~10 &mu;m/sec in each direction.</li>
	<li>Monitor the signal of the InSb detector, which is the spectral measurement signal. Once the detector signal reaches its maximum value (be careful not to saturate the detector), stop the motorized stages and turn off the cartridge heaters (temperature controller).</li>
	<li>Wait for ~10 min for the fiber to solidify (the detector signal will decrease a little during this process, most likely due to the temperature dependence of the refractive index or thermal contraction).</li>
	<li>Translate the heater block along the fiber towards a fiber clamp where the fiber is untapered. Then translate the heater block away from the fiber using the slit in the heater block to allow the fiber to pass.</li>
	<li>Characterize the SCG through spectral measurements with the monochromator. An InAs filter may be needed to accurately measure the long wavelength portion of the spectrum.</li>
	<li>Remove the fiber if desired.</li>
</ol>

<ol>
	<li>Marandi, A., Rudy, C. W., Plotnichenko, V. G., Dianov, E. M., Vodopyanov, K. L., Byer, R. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mid-infrared+supercontinuum+generation+in+tapered+chalcogenide+fiber+for+producing+octave-spanning+frequency+comb+around+3+&#956;m.">Mid-infrared supercontinuum generation in tapered chalcogenide fiber for producing octave-spanning frequency comb around 3 &#956;m.</a> Optics Express. 20, 24218-24225 (2012).</li><li>Schliesser, A., Picque, N., Hansch, T. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mid-infrared+frequency+combs.">Mid-infrared frequency combs.</a> Nature Photonics. 6, 440-449 (2012).</li><li>Diddams, S. A., Hollberg, L., Mbele, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Molecular+fingerprinting+with+the+resolved+modes+of+a+femtosecond+laser+frequency+comb.">Molecular fingerprinting with the resolved modes of a femtosecond laser frequency comb.</a> Nature. 445, 627-630 (2007).</li><li>Thorpe, M. J., Balslev-Clausen, D., Kirchner, M. S., Ye, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cavity-enhanced+optical+frequency+comb+spectroscopy:+application+to+human+breath+analysis.">Cavity-enhanced optical frequency comb spectroscopy: application to human breath analysis.</a> Optics Express. 16, 2387-2397 (2008).</li><li>Sears, C. M. S., Colby, E., England, R. J., Ischebeck, R., McGuinness, C., Nelson, J., Noble, R., Siemann, R. H., Spencer, J., Walz, D., Plettner, T., Byer, R. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Phase+stable+net+acceleration+of+electrons+from+a+two-stage+optical+accelerator.">Phase stable net acceleration of electrons from a two-stage optical accelerator.</a> Physical Review Letters. 11, 101301 (2008).</li><li>Popmintchev, T., Chen, M. C., Arpin, P., Murnane, M. M., Kapteyn, H. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+attosecond+nonlinear+optics+ofbright+coherent+X-ray+generation.">The attosecond nonlinear optics ofbright coherent X-ray generation.</a> Nature Photonics. 4, 822-832 (2010).</li><li>Dudley, J. M., Taylor, J. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Supercontinuum generation in optical fibers. , (2010).</li><li>Birks, T. A., Wadsworth, W. J., Russell, P. S. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Supercontinuum+generation+in+tapered+fibers.">Supercontinuum generation in tapered fibers.</a> Optics Letters. 25, 1415-1417 (2000).</li><li>Leindecker, N., Marandi, A., Byer, R. L., Vodopyanov, K. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Broadband+degenerate+OPO+for+mid-infrared+frequency+comb+generation.">Broadband degenerate OPO for mid-infrared frequency comb generation.</a> Optics Express. 19, 6296-6302 (2011).</li><li>Liao, M., Yan, X., Gao, W., Duan, Z., Qin, G., Suzuki, T., Ohishi, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Five-order+SRSs+and+supercontinuum+generation+from+a+tapered+tellurite+microstructured+fiber+with+longitudinally+varying+dispersion.">Five-order SRSs and supercontinuum generation from a tapered tellurite microstructured fiber with longitudinally varying dispersion.</a> Optics Express. 19, 15389-15396 (2011).</li><li>M&#228;gi, E. C., Steinvurzel, P., Eggleton, B. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tapered+photonic+crystal+fibers.">Tapered photonic crystal fibers.</a> Optics Express. 12, 776-784 (2004).</li><li>Ozeki, T., Kawasaki, B. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optical+directional+coupler+using+tapered+sections+in+multimode+fibers.">Optical directional coupler using tapered sections in multimode fibers.</a> Applied Physics Letters. 28, 528-529 (1976).</li><li>Yataki, M. S., Payne, D. N., Varnahm, M. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=All-fibre+wavelength+filters+using+concatenated+fused-taper+couplers.">All-fibre wavelength filters using concatenated fused-taper couplers.</a> Electronic Letters. 21, 248-249 (1985).</li><li>Chandalia, J. K., Eggleton, B. J., Windeler, R. S., Kosinski, S. G., Liu, X., Xu, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adiabatic+coupling+in+tapered+air-silica+microstructured+optical+fiber.">Adiabatic coupling in tapered air-silica microstructured optical fiber.</a> IEEE Photonics Technology Letters. 13, 52-54 (2001).</li><li>Mora, J., D&#237;ez, A., Fonjallaz Andr&#233;z, P. Y., Popov, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tunable+dispersion+compensator+based+on+a+fiber+Bragg+grating+written+in+a+tapered+fiber.">Tunable dispersion compensator based on a fiber Bragg grating written in a tapered fiber.</a> IEEE Photonics Technology Letters. 16, 2631-2633 (2004).</li><li>Rusu, M., Herda, R., Kivist&#246;, S., Okhotnikov, O. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fiber+taper+for+dispersion+management+in+a+mode-locked+ytterbium+fiber+laser.">Fiber taper for dispersion management in a mode-locked ytterbium fiber laser.</a> Optics Letters. 31, 2257-2259 (2006).</li><li>Alfanao, R. R., Shapiro, S. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Emission+in+the+region+4000+to+7000+A+via+four-photon+coupling+in+glass.">Emission in the region 4000 to 7000 A via four-photon coupling in glass.</a> Physical Review Letters. 24, 584-587 (1970).</li><li>Eggleton, B. J., Luther-Davies, B., Richardson, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chalcogenide+photonics.">Chalcogenide photonics.</a> Nature Photonics. 5, 141148 (2011).</li><li>Snopatin, G. E., Shiryaev, V. S., Plotnichenko, V. G., Dianov, E. M., Churbanov, M. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-purity+chalcogenide+glasses+for+fiber+optics.">High-purity chalcogenide glasses for fiber optics.</a> Inorganic Materials. 45, 1439-1460 (2009).</li><li>Harbold, J. M., Ilday, F. O., Wise, F. W., Sanghera, J. S., Nguyen, V. Q., Shaw, L. B., Aggarwal, I. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Highly+nonlinear+As-S-Se+glasses+for+all-optical+switching.">Highly nonlinear As-S-Se glasses for all-optical switching.</a> Optics Letters. 27, 119-121 (2002).</li><li>Hudson, D. D., Dekker, S. A., Magi, E. C., Judge, A. C., Jackson, S. D., Li, E., Sanghera, J. S., Shaw, L. B., Aggarwal, I. D., Eggleton, B. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Octave+spanning+supercontinuum+in+an+As2S3+taper+using+ultralow+pump+pulse+energy.">Octave spanning supercontinuum in an As2S3 taper using ultralow pump pulse energy.</a> Optics Letters. 36, 1122-1124 (2011).</li><li>Domachuk, P., Wolchover, N. A., Cronin-Golomb, M., Wang, A., George, A. K., Cordeiro, C. M. B., Knight, J. C., Omenetto, F. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Over+4000+nm+bandwidth+of+mid-IR+supercontinuum+generation+in+sub-centimeter+segments+ofhighly+nonlinear+tellurite+PCFs.">Over 4000 nm bandwidth of mid-IR supercontinuum generation in sub-centimeter segments ofhighly nonlinear tellurite PCFs.</a> Optics Express. 6, 7161-7168 (2008).</li><li>Hu, J., Menyuk, C. R., Shaw, L. B., Sanghera, J. S., Aggarwal, I. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Maximizing+the+bandwidth+of+supercontinuum+generation+in+As2Se3+chalcogenide+fibers.">Maximizing the bandwidth of supercontinuum generation in As2Se3 chalcogenide fibers.</a> Optics Express. 18, 6722-6739 (2010).</li><li>El-Amraoui, M., Fatome, J., Jules, J. C., Kibler, B., Gadret, G., Fortier, C., Smektala, F., Skripatchev, I., Polacchini, C. F., Messaddeq, Y., Troles, J., Brilland, L., Szpulak, M., Renversez, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Strong+infrared+spectral+broadening+inlow-loss+As-S+chalcogenide+suspended+core+microstructured+optical+fibers.">Strong infrared spectral broadening inlow-loss As-S chalcogenide suspended core microstructured optical fibers.</a> Optics Express. 18, 4547-4556 (2010).</li><li>Marandi, A., Leindecker, N., Byer, R. L., Vodopyanov, K. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coherence+properties+of+a+broadband+femtosecond+mid-IR+optical+parametric+oscillator+operating+at+degeneracy.">Coherence properties of a broadband femtosecond mid-IR optical parametric oscillator operating at degeneracy.</a> Optics Express. 20, 7255-7262 (2012).</li><li>Dudley, J. M., Coen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coherence+properties+of+supercontinuum+spectra+generated+in+photonic+crystal+and+tapered+optical+fibers.">Coherence properties of supercontinuum spectra generated in photonic crystal and tapered optical fibers.</a> Optics Letters. 27, 1180-1182 (2002).</li><li>Corwin, K. L., Newbury, N. R., Dudley, J. M., Coen, S., Diddams, S. A., Weber, K., Windeler, R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fundamental+noise+limitations+to+supercontinuum+generation+in+microstructure+fiber.">Fundamental noise limitations to supercontinuum generation in microstructure fiber.</a> Physical Review Letters. 90, 113904 (2003).</li><li>Birks, T. A., Li, Y. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+shape+of+fiber+tapers.">The shape of fiber tapers.</a> Journal of Lightwave Technology. 10, 432-438 (1992).</li><li>Churbanov, M. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-purity+chalcogenide+glasses+as+materials+for+fiber+optics.">High-purity chalcogenide glasses as materials for fiber optics.</a> Journal of Non-Crystalline Solids. 184, 25-29 (1995).</li></ol>

A United States provisional patent has been filed protecting the technology disclosed in this article.

We have demonstrated a novel fiber tapering procedure and verified its validity by performing SCG in the mid-IR. To the best of our knowledge, the alternative method for this application is based on determining the fiber pulling length required to create a tapered fiber diameter that adds enough waveguide dispersion to optimize SCG in the fiber taper through calculation; however, since the pulling length needed to maximize the spectral broadening for a specific length of fiber varies for each experiment, this calc...

After being first produced in the visible wavelength range1,7 SCG sources have shifted towards the mid-IR, largely driven by applications in spectroscopy.3, 4 Chalcogenide fibers, which include sulfides, selenides, and tellurides, have been a popular material for the mid-IR due to their low propagation loss and high nonlinearity,18 less than 100 dB/km19 and ~200 times that of silica for As2S3,20 respectively. However, the zero GVD wavelength of most chalcogenides is located in the mid-IR, beyond the center wavelength of the majority of available ultrafast pump sources, making SCG challenging in a bulk material or a standard single mode chalcogenide fiber. Waveguide dispersion can be used to modify the zero GVD point for SCG.7 Methods for introducing strong waveguide dispersion include fiber tapering,8, 21 using microstructured fibers,22-24 or even a combination of the two.10 By shifting the zero GVD wavelength below the pump wavelength, the pump will experience anomalous dispersion in the fiber. In the anomalous dispersion regime, soliton formation occurs through balancing the nonlinear chirp caused by self phase modulation and the linear chirp caused by GVD. For a femtosecond pump source, spectral broadening is usually dominated by soliton fission or pulse breaking, which occurs after an initial temporal compression as the pulse propagates along the fiber.7 In the case of fiber tapering, calculating the total GVD-including both material and waveguide dispersion-can provide an approximation of the final taper diameter needed to produce a significantly broadened spectrum. Due to SCG's strong dependence on GVD and fluctuations between experimental trials, including changes to the fiber length before the tapered region and coupling of the pump to the fiber, the calculated approximation is not sufficient for achieving an optimized taper in a single trial. Spectral monitoring allows for these variations in experimental setup to be observed and accounted for in in-situ tapering.
Moreover, generating an efficient supercontinuum (SC) in a short tapered fiber reduces the amount of nonlinear noise amplification preserving the coherence of the SCG and the frequency comb properties of the pump source.25-27 Proper dispersion management, and therefore the necessity of in-situ tapering, becomes even more critical when the fiber length is short, as the SCG tolerance scales with length.
The in-situ tapering setup begins with the pump source, which is the subharmonic of a mode-locked Er-doped fiber laser,9 coupled into the core of the As2S3 fiber that will be tapered. The output of the fiber is then coupled to a device that characterizes the spectral profile. In the experiment, a InSb detector after a monochromator with ~20 nm of resolution is used to monitor a portion of the output spectrum where there is initially a very low signal from the pump source (at ~3.9 &mu;m) so that the fiber may be monitored while tapering. When the fiber is tapered and the spectrum broadens, the spectral measurement signal increases as the dispersion is optimized for the individual experiment. By monitoring the spectrum during the tapering procedure, tapering can be stopped at the moment when the spectral broadening has been maximized. In-situ tapering allows for optimized dispersion management for efficient SCG in a single fiber taper. Tapering with a static, narrow heat zone produces a short fiber taper waist,28 which allows for low-noise SCG. Together, in-situ static tapering can enable coherent, low-noise, octave-spanning SCG in the mid-IR.

<table border="1">
		<tbody>
		 <tr>
			<td>Name of Equipment</td>
			<td>Company</td>
			<td>Catalog Number</td>
			<td>Comments</td>
		 </tr>
		 <tr>
			<td>Motorized Linear Stages</td>
			<td>Newport</td>
			<td>MFA-PPD</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Motorized Stage Controller</td>
			<td>Newport</td>
			<td>ESP301</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Aluminum Block</td>
			<td>Any vendor.</td>
			<td></td>
			<td>Dimensions will vary depending on desired taper length.</td>
		 </tr>
		 <tr>
			<td>RTD Sensor</td>
			<td>Omega</td>
			<td>1PT100GX1510</td>
			<td></td>
		 </tr>
		 <tr>
			<td>Cartridge Heaters</td>
			<td>Omega</td>
			<td>CSS-01115/120V</td>
			<td></td>
		 </tr>
		 <tr>
			<td>Temperature Controller</td>
			<td>Omega</td>
			<td>CSC32</td>
			<td></td>
		 </tr>
		 <tr>
			<td>Input Coupling Linear Translation Stage</td>
			<td>CVI</td>
			<td>07TXS224</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Output Coupling Linear Translation Stage</td>
			<td>Newport</td>
			<td>422-1S</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>XYZ Linear Translation Stage</td>
			<td>Newport</td>
			<td>461</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Assorted posts, optics mounts, bases, and forks</td>
			<td>Any vendor.</td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
			<td>Optical Breadboard</td>
			<td>Thorlabs</td>
			<td>MB12</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Input Coupling ZnSe Lens</td>
			<td>Thorlabs</td>
			<td>AL72512-E</td>
			<td>Available from other vendors. Input coupling focal length depends on pump source and fiber mode field diameter.</td>
		 </tr>
		 <tr>
			<td>Output Coupling ZnSe Lens</td>
			<td>Edmund Optics</td>
			<td>NT62-961</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Box</td>
			<td>Any type will do.</td>
			<td></td>
			<td>Must be large enough to allow stage movement. Needs apertures for input and output coupling of light.</td>
		 </tr>
		 <tr>
			<td>Ceramic Optical Post</td>
			<td>Any vendor.</td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
			<td>Digital Microscope</td>
			<td>Any vendor.</td>
			<td></td>
			<td>Optional.</td>
		 </tr>
		 <tr>
			<td>Table Clamps</td>
			<td>Thorlabs</td>
			<td>CL5</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Bare Fiber clamps</td>
			<td>Thorlabs</td>
			<td>HFF003</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
		 <td></td>
		 <td></td>
		 <td></td>
		 <td>Table 1. Tapering Setup Materials.</td>
	 </tr>
		 <tr>
			<td>As2S3 Optical Fiber</td>
			<td>Fiber Optics Research Center of the Russian Academy of Sciences</td>
			<td></td>
			<td>Available from other vendors, such as CorActive. </td>
		 </tr>
		 <tr>
			<td>Beavertail Cleaver</td>
			<td>Fiber Network Tools</td>
			<td>S-315</td>
			<td>Available from other vendors. Hand cleaving or polishing fiber tips can also produce high quality fiber tips.</td>
		 </tr>
		 <tr>
			<td>KimWipes</td>
			<td>Kimberly-Clark Professional</td>
			<td>34120</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Acetone, Isopropanol</td>
			<td>Any vendor.</td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
		 <td></td>
		 <td></td>
		 <td></td>
		 <td>Table 2. Materials for Chalcogenide Fiber Preparation.</td>
	 </tr>
		 <tr>
			<td>Pyrocam</td>
			<td>Ophir Photonics</td>
			<td>Pyrocam III Series</td>
			<td>Any camera with sensitivity at pump wavelength will work.</td>
		 </tr>
		 <tr>
			<td>Monochromator</td>
			<td>Photon Technology International</td>
			<td></td>
			<td>A 100 line/mm grating was used. Any spectral measurement device will work (e.g. longpass filter). </td>
		 </tr>
		 <tr>
			<td>CaF2 Lenses</td>
			<td>Thorlabs</td>
			<td>LB5922</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>InAs Filter</td>
			<td>Any vendor.</td>
			<td></td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Amplified InSb Detector</td>
			<td>Hamamatsu</td>
			<td>P4631-03</td>
			<td>Available from other vendors.</td>
		 </tr>
		 <tr>
			<td>Computer</td>
			<td>Any vendor.</td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
			<td>DAQ</td>
			<td>National Instruments</td>
			<td>USB X Series</td>
			<td></td>
		 </tr>
		 <tr>
			<td>Labview software for motorized stages</td>
			<td>National Instruments</td>
			<td></td>
			<td>Optional. Custom program.</td>
		 </tr>
		 <tr>
			<td>Labview software for collecting detector data</td>
			<td>National Instruments</td>
			<td></td>
			<td>Optional. Custom program.</td>
		 </tr>
		 <tr>
			<td>Assorted posts, optics mounts, bases, and forks</td>
			<td></td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
			<td>1" Gold mirrors</td>
			<td>Any vendor.</td>
			<td></td>
			<td></td>
		 </tr>
		 <tr>
			<td>Chopper and controller</td>
			<td>Any vendor.</td>
			<td>SRS Model SR540</td>
			<td>Optional. Depends on detector being used.</td>
		 </tr>
		 <tr>
		 <td></td>
		 <td></td>
		 <td></td>
		 <td>Table 3. Materials for In-situ Tapering Procedure.</td>
	 </tr>
		</tbody>
 </table>

in-situ tapering of chalcogenide fiber for mid-infrared supercontinuum generation

Supercontinuum generation (SCG) in a tapered chalcogenide fiber is desirable for broadening mid-infrared (or mid-IR, roughly the 2-20 &mu;m wavelength range) frequency combs1, 2 for applications such as molecular fingerprinting, 3 trace gas detection, 4 laser-driven particle acceleration, 5 and x-ray production via high harmonic generation. 6 Achieving efficient SCG in a tapered optical fiber requires precise control of the group velocity dispersion (GVD) and the temporal properties of the optical pulses at the beginning of the fiber, 7 which depend strongly on the geometry of the taper. 8 Due to variations in the tapering setup and procedure for successive SCG experiments-such as fiber length, tapering environment temperature, or power coupled into the fiber, in-situ spectral monitoring of the SCG is necessary to optimize the output spectrum for a single experiment.
	In-situ fiber tapering for SCG consists of coupling the pump source through the fiber to be tapered to a spectral measurement device. The fiber is then tapered while the spectral measurement signal is observed in real-time. When the signal reaches its peak, the tapering is stopped. The in-situ tapering procedure allows for generation of a stable, octave-spanning, mid-IR frequency comb from the sub harmonic of a commercially available near-IR frequency comb. 9 This method lowers cost due to the reduction in time and materials required to fabricate an optimal taper with a waist length of only 2 mm.
	The in-situ tapering technique can be extended to optimizing microstructured optical fiber (MOF) for SCG10 or tuning of the passband of MOFs, 11 optimizing tapered fiber pairs for fused fiber couplers12 and wavelength division multiplexers (WDMs), 13 or modifying dispersion compensation for compression or stretching of optical pulses.14-16

After successful completion of the in-situ tapering procedure, the pump spectrum broadened to cover from 2.2 to 5 &mu;m (at ~40 dB below the peak), as seen in Figure 3. The pump pulse energy in the As2S3 fiber was ~250 pJ with an initial pulse length under 100 fsec. The short length of the tapered waist, ~2.1 mm, allows for generation of a broadband, coherent SC. This preserves the frequency comb properties of the pump source. More information about the frequency comb and o...

Watch this Scientific Journal Video about In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation at JoVE.com

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation

We describe a method for in-situ tapering of As2S3 fibers to achieve efficient mid-infrared supercontinuum generation. By tapering while monitoring the supercontinuum&#x2019;s spectrum, the spectral width can be maximized for a fiber taper. In-situ fiber tapering can be applied to optimize the performance of other fiber-based devices.

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation

Supercontinuum  generation (SCG) in a tapered chalcogenide fiber is desirable for broadening mid-infrared  (or mid-IR, roughly the 2-20 &mu;m wavelength ...

in-situ-tapering-chalcogenide-fiber-for-mid-infrared-supercontinuum

Research

JoVE Journal

Engineering

12.2K Views.  Stanford University. We describe a method for in-situ tapering of As2S3 fibers to achieve efficient mid-infrared supercontinuum generation. By tapering while monitoring the supercontinuum’s spectrum, the spectral width can be maximized for a fiber taper. In-situ fiber tapering can be applied to optimize the performance of other fiber-based devices.