This work was supported by the Deutsche Forschungsgemeinschaft (DFG) within the framework of SPP 1708. GT thanks the Leopoldina Nationale Akademie der Wissenschaften for a postdoctoral scholarship.

Caution: Always be cautious when working with chemicals. Apply common safety precautions, including the appropriate utilization of gloves, goggles, and a lab coat at all times. In particular, be aware that all discussed compounds containing heavy elements, as well as their elemental sources, are of high toxicity. 1,2-diaminoethane is a corrosive liquid. Alkaline metals and ternary solid-state products may react pyrophorically with air and moisture.
Note: All manipulations are performed in an argon atmosphere using standard Schlenk or glovebox techniques under strict exclusion of air and external moisture. Solids or solutions containing heavy element metalate species or precursors are stored under the exclusion of light by wrapping the respective containers with aluminum foil for inhibition of a light-induced decomposition.
1. Preparation of Solvents and Solutions
<ol>
	<li>Add 1 L of freshly purchased 1,2-diaminoethane to 25 g of CaH2 and stir overnight. Reflux (Tb = 116 &#176;C) until no H2 is generated (approximately 12 h).
	<ol>
		<li>Distill at ambient pressure.</li>
	</ol>
	</li>
	<li>Add 1 L of oxolane (THF) to 10 g of NaK alloy and stir overnight. Reflux (Tb = 66 &#176;C) for at least 12 h. Distill at ambient pressure.</li>
	<li>Make a saturated solution of [Rh(PPh3)3Cl] by adding 150 mg of [Rh(PPh3)3Cl] to 10 mL of THF. Stir overnight at room temperature (RT) and filtrate with an inert gas filter frit of low porosity.</li>
</ol>
2. High-temperature Solid-state Reactions
<ol>
	<li>Synthesis of PbSe2
	<ol>
		<li>Place 3.81 g of elemental Se in a borosilicate ampule and add 5 g of elemental Pb on top. Heat it with an oxygen/methane burner until optical homogeneity of the melt is achieved (approximately 10 min). Knock the ampule gently with a cork ring throughout the synthesis to detach sublimed Se from the ampule wall, which will then drop back into the reaction mixture.</li>
		<li>Allow the ampule to cool down to room temperature. Break the ampule with a pestle in a mortar and manually remove all remaining splinters of the ampule. Pestle the crude PbSe2 thoroughly.</li>
	</ol>
	</li>
	<li>Synthesis of K2PbSe2
	<ol>
		<li>Place 0.95 g of elemental K and 5 g of elemental Pb in a thick-walled borosilicate ampule. Slowly increase the heat with an oxygen/methane burner until optical homogeneity of the melt is achieved (approximately 20 min).</li>
		<li>Carefully add 1.9 g of elemental Se pellets to the molten alloy. Upon the complete addition, increase the temperature until the reaction mixture emits bright yellow/white radiation (approximately 10 min) and hold the temperature for 10 min. Decrease the reaction temperature slightly if the radiation color turns to pure, bright white (a temperature close to the melting point of the ampule).</li>
		<li>Allow the reaction mixture to cool down to RT. Break the ampule and manually remove all remaining splinters of the ampule and a regulus of elemental lead. Pestle the crude K2PbSe2 thoroughly.</li>
	</ol>
	</li>
</ol>
3. In Situ Reduction
<ol>
	<li>Synthesis of a solution of [K(18-crown-6)]2[Pb2Se3]
	<ol>
		<li>Place 2 g of PbSe2, 3.1 g of 18-crown-6, 250 mL of 1,2-diaminoethane, and a large stir bar in a round-bottom N2-flask on a stir plate. Stir rigorously at RT and slowly add 0.45 g of elemental K.</li>
		<li>Stir overnight at RT and filter the solution with an inert gas filter frit of low porosity (pore diameters: D3, 16-40 &#181;m or D4, 10-16 &#181;m).</li>
	</ol>
	</li>
</ol>
4. Solvothermal Reactions
<ol>
	<li>Synthesis of K4[PbSe4]&#183;en&#183;NH3 
	<ol>
		<li>Place 0.5 g of K2PbSe2 and 2 mL of 1,2-diaminoethane in a 10-mL glass vial in a 15-mL polytetrafluorethylene vial in a standard stainless-steel autoclave. Close the autoclave tightly and it heat in an oven to 150 &#176;C for 5 days.</li>
		<li>Turn off the oven and leave it for 1 d to slowly cool to RT. Transfer the reaction mixture into paratone oil and manually select crystals of K4[PbSe4]&#183;en&#183;NH3 under a standard light microscope at 15-40X magnification.</li>
	</ol>
	</li>
</ol>
5. Reactive Layering
<ol>
	<li>Synthesis of [(RhPPh3)6(&#181;3-Se)8]&#183;0.5en
	<ol>
		<li>Place 10 mL of a solution of [K(18-crown-6)]2[Pb2Se3] in a 50-mL flask, add 10 mL of a saturated solution of [Rh(PPh3)3Cl] in THF, and stir overnight.</li>
		<li>Filter the reaction solution with an inert gas filter frit of low porosity and remove the solvent under dynamic vacuum slowly during 24 h. Transfer the crude reaction product into paratone oil and manually select crystals of [(RhPPh3)6(&#181;3-Se)8]&#183;0.5en under a standard light microscope at 15-40X magnification.</li>
	</ol>
	</li>
	<li>Synthesis of {[K(18-crown-6)]-[K(en)2]K[Rh3(CN)2(PPh3)4(&#181;3-Se)2(&#181;-PbSe)]}2&#183;1.3en
	<ol>
		<li>Place 10 mL of a solution of [K(18-crown-6)]2[Pb2Se3] in a Schlenk tube and carefully layer it with 10 mL of a saturated solution of [Rh(PPh3)3Cl] in THF. Cover the Schlenk tube completely in aluminum foil and leave it undisturbed for 4 weeks.</li>
		<li>Transfer the resulting solid into paratone oil and select single crystals quickly under a light microscope.</li>
	</ol>
	</li>
</ol>
6. Analysis of the Solutions and Compounds
<ol>
	<li>Place 50 mg of &#34;K2PbSe2&#34; onto an acrylic glass sample carrier (the compound reacts with elemental Si) and cover it with tape. Place it under ambient conditions in a powder X-ray diffractometer (PXRD) and record the diffraction data within 1 h23.</li>
	<li>Place 0.6 mL of a solution of [K(18-crown-6)]2[Pb2Se3] in a nuclear magnetic resonance (NMR) tube and thoroughly seal the latter with protective tape. Transfer it quickly into the NMR probe and record 77Se and 205Pb NMR with at least 2,000 and 5,000 pulses, respectively25.</li>
	<li>Select a single crystal under a light microscope and mount it on the goniometer head of the diffractometer. Measure it with high redundancy to enable the adequate absorption corrections23-33.</li>
	<li>Perform a simultaneous optimization of the electronic and geometric structure of [Rh3(CN)2(PPh3)4(&#181;3Se)2(&#181;PbSe)]3-. Apply the conductor-like screening model (COSMO) with a 10% increase of the default radii to account for charge compensation28.
	<ol>
		<li>Calculate the vibrational frequencies to ensure the energetic minimum28.</li>
		<li>Perform Mulliken and/or natural bond orbital (NBO) analyses based on the density functional theory (DFT) wave function to obtain the atomic charges28.</li>
		<li>Calculate in-orbital contributions to the &#34;relaxed&#34; and the original structures of a) the complete cluster, b) the CO/PbSe-free cluster, and c) the CO/PbSe ligand, and compare the results28.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Zhao, L. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultralow+thermal+conductivity+and+high+thermoelectric+figure+of+merit+in+SnSe+crystals.">Ultralow thermal conductivity and high thermoelectric figure of merit in SnSe crystals.</a> Nature. 508 (7496), 373-377 (2014).</li><li>Chung, I., Kanatzidis, M. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metal+Chalcogenides:+A+Rich+Source+of+Nonlinear+Optical+Materials.">Metal Chalcogenides: A Rich Source of Nonlinear Optical Materials.</a> Chem. Mater. 26 (1), 849-869 (2014).</li><li>Lhuillier, E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-Dimensional+Colloidal+Metal+Chalcogenides+Semiconductors:+Synthesis,+Spectroscopy,+and+Applications.">Two-Dimensional Colloidal Metal Chalcogenides Semiconductors: Synthesis, Spectroscopy, and Applications.</a> Acc. Chem. Res. 48 (1), 22-30 (2015).</li><li>Heine, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transition+metal+chalcogenides:+ultrathin+inorganic+materials+with+tunable+electronic+properties.">Transition metal chalcogenides: ultrathin inorganic materials with tunable electronic properties.</a> Acc. Chem. Res. 48 (1), 65-72 (2015).</li><li>Gao, M. R., Xu, Y. F., Jiang, J., Yu, S. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nanostructured+metal+chalcogenides:+synthesis,+modification,+and+applications+in+energy+conversion+and+storage+devices.">Nanostructured metal chalcogenides: synthesis, modification, and applications in energy conversion and storage devices.</a> Chem. Soc. Rev. 42, 2986-3017 (2013).</li><li>Jackson, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multiexciton+Solar+Cells+of+CuInSe2+Nanocrystals.">Multiexciton Solar Cells of CuInSe2 Nanocrystals.</a> J. Phys. Chem. Lett. 5 (2), 304-309 (2014).</li><li>Androulakis, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dimensional+Reduction:+A+Design+Tool+for+New+Radiation+Detection+Materials.">Dimensional Reduction: A Design Tool for New Radiation Detection Materials.</a> Adv. Mater. 23 (36), 4163-4167 (2011).</li><li>Sheldrick, W. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polychalcogenide+Anions:+Structural+Diversity+and+Ligand+Versatility.">Polychalcogenide Anions: Structural Diversity and Ligand Versatility.</a> Z. Anorg. Allg. Chem. 638 (15), 2401-2424 (2012).</li><li>Dehnen, S., Melullis, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+coordination+chemistry+approach+towards+ternary+M/14/16+anions.">A coordination chemistry approach towards ternary M/14/16 anions.</a> Coord. Chem. Rev. 251 (9-10), 1259-1280 (2007).</li><li>Santner, S., Heine, J., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synthesis+of+Crystalline+Chalcogenides+in+Ionic+Liquids.">Synthesis of Crystalline Chalcogenides in Ionic Liquids.</a> Angew. Chem. Int. Ed. 55 (3), 876-893 (2015).</li><li>Heine, J., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=From+Simple+Chalcogenidotetrelate+Precursors+to+Complex+Structures+and+Functional+Compounds.">From Simple Chalcogenidotetrelate Precursors to Complex Structures and Functional Compounds.</a> Z. Anorg. Allg. Chem. 638 (15), 2425-2440 (2012).</li><li>Ruzin, E., Zent, E., Matern, E., Massa, W., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Syntheses,+Structures,+and+Comprehensive+NMR+Spectroscopic+Investigations+of+Hetero-Chalcogenidometallates:+The+Right+Mix+toward+Multinary+Complexes.">Syntheses, Structures, and Comprehensive NMR Spectroscopic Investigations of Hetero-Chalcogenidometallates: The Right Mix toward Multinary Complexes.</a> Chem. Eur. J. 15 (21), 5230-5244 (2009).</li><li>Leusmann, E., Geringer, E., Weinert, B., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ir3(cod)3(&#181;3-S)2](&#181;3-S)SnCl}+2+&#8211;+a+Ternary+Ir-Sn-S+cluster+with+the+Iridium+Atoms+in+Three+Different+Chemical+Environments.">Ir3(cod)3(&#181;3-S)2](&#181;3-S)SnCl} 2 &#8211; a Ternary Ir-Sn-S cluster with the Iridium Atoms in Three Different Chemical Environments.</a> Dalton Trans. 45, 15298-15302 (2016).</li><li>Pyykk&#246;, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Relativistic+Effects+in+Chemistry:+More+Common+Than+You+Thought.">Relativistic Effects in Chemistry: More Common Than You Thought.</a> Ann. Rev. Phys. Chem. 63, 45-64 (2012).</li><li>Brazel, B., Hoppe, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Zur+Kenntnis+von+K4PbO4+und+Rb4PbO4.">Zur Kenntnis von K4PbO4 und Rb4PbO4.</a> Z. Anorg. Allg. Chem. 505 (10), 99-104 (1983).</li><li>Jones, C. D. W., DiSalvo, F. J., Haushalter, R. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synthesis+and+X-ray+Crystal+Structure+of+K4PbTe3&#183;2(en).">Synthesis and X-ray Crystal Structure of K4PbTe3&#183;2(en).</a> Inorg. Chem. 37 (4), 821-823 (1998).</li><li>Bj&#246;rgvinsson, M., Sawyer, J. F., Schrobilgen, G. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dilead(II)+Chalcogenide+anions+Pb2Ch32-+(Ch+=+Se,+Te):+A+207Pb,+125Te,+and+77Se+Solution+NMR+Study.+X-ray+crystal+structure+of+(2,2,2-crypt-K+)2Pb2Se32-.">Dilead(II) Chalcogenide anions Pb2Ch32- (Ch = Se, Te): A 207Pb, 125Te, and 77Se Solution NMR Study. X-ray crystal structure of (2,2,2-crypt-K+)2Pb2Se32-.</a> Inorg. Chem. 26 (5), 741-749 (1987).</li><li>Scharfe, S., Kraus, F., Stegmaier, S., Schier, A., F&#228;ssler, T. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Zintl+Ions,+Cage+Compounds,+and+Intermetalloid+Clusters+of+Group+14+and+Group+15+Elements.">Zintl Ions, Cage Compounds, and Intermetalloid Clusters of Group 14 and Group 15 Elements.</a> Angew. Chem. Int. Ed. 50 (16), 3630-3670 (2011).</li><li>Joannis, C. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Action+du+sodammonium+et+du+potassamonium+sur+quelques+m&#233;taux.">Action du sodammonium et du potassamonium sur quelques m&#233;taux.</a> C. R. Hebd. Seances Acad. Sci. 113, 795-798 (1891).</li><li>Joannis, C. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sur+quelques+alliages+bien+d&#232;finis+de+sodium.">Sur quelques alliages bien d&#232;finis de sodium.</a> C. R. Hebd. Seances Acad. Sci. 114, 585-587 (1892).</li><li>Diehl, L., Khodadeh, K., Kummer, D., Str&#228;hle, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Anorganische+Polyederverbindungen,+III.+Zintl's+&#8222;Polyanionige+Salze&amp;#34;:+Darstellung+und+Eigenschaften+der+kristallinen+Verbindungen+[Na4&#183;7+en]Sn9,+[Na4&#183;5+en]Ge9+und+[Na3&#183;4+en]Sb7+und+ihrer+L&#246;sungen.+Die+Kristallstruktur+von+[Na4&#183;7+en]+Sn9.">Anorganische Polyederverbindungen, III. Zintl's &#8222;Polyanionige Salze&amp;#34;: Darstellung und Eigenschaften der kristallinen Verbindungen [Na4&#183;7 en]Sn9, [Na4&#183;5 en]Ge9 und [Na3&#183;4 en]Sb7 und ihrer L&#246;sungen. Die Kristallstruktur von [Na4&#183;7 en] Sn9.</a> Chem. Ber. 109 (10), 3404-3418 (1976).</li><li>Demazeau, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Solvothermal+Processes:+Definition,+Key+Factors+Governing+the+Involved+Chemical+Reactions+and+New+Trends.">Solvothermal Processes: Definition, Key Factors Governing the Involved Chemical Reactions and New Trends.</a> Z. Naturforsch. 65b, 999-1006 (2010).</li><li>Thiele, G., Kr&#252;ger, T., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=K4[PbSe4]&#8901;en&#8901;NH3:+A+Non-Oxide,+Non-Halide+Inorganic+Lead(IV)+Compound.">K4[PbSe4]&#8901;en&#8901;NH3: A Non-Oxide, Non-Halide Inorganic Lead(IV) Compound.</a> Angew. Chem. Int. Ed. 53 (18), 4699-4703 (2014).</li><li>Thiele, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=K2Hg2Se3:+Large-Scale+Synthesis+of+a+Photoconductor+Material+Prototype+with+a+Columnar+Polyanionic+Substructure.">K2Hg2Se3: Large-Scale Synthesis of a Photoconductor Material Prototype with a Columnar Polyanionic Substructure.</a> Chem. Mater. 27 (11), 4114-4118 (2015).</li><li>Thiele, G., Vondung, L., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=About+the+Syntheses+of+Chalcogenidometalates+by+in-situ+Reduction+with+Elemental+Alkali+Metals.">About the Syntheses of Chalcogenidometalates by in-situ Reduction with Elemental Alkali Metals.</a> Z. Anorg. Allg. Chem. 641 (2), 247-252 (2015).</li><li>Thiele, G., You, Z., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Molecular+CHEVREL-like+Clusters+[(RhPPh3)6(&#181;3-Se)8]+and+[Pd6(&#181;3-Te)8]4-.">Molecular CHEVREL-like Clusters [(RhPPh3)6(&#181;3-Se)8] and [Pd6(&#181;3-Te)8]4-.</a> Inorg. Chem. 54 (6), 2491-2493 (2015).</li><li>Thiele, G., Balmer, M., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synthesis,+Structure+and+Electronic+Situation+of+[Rh6Te8(PPh3)6]&#183;4C6H6.">Synthesis, Structure and Electronic Situation of [Rh6Te8(PPh3)6]&#183;4C6H6.</a> Zeitschrift f&#252;r Naturforschung B. 71 (5), 391-394 (2016).</li><li>Thiele, G., Franzke, Y., Weigend, F., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term={&#181;-PbSe}:+A+Heavy+CO+Homologue+as+an+Unexpected+Ligand.">{&#181;-PbSe}: A Heavy CO Homologue as an Unexpected Ligand.</a> Angew. Chem. Int. Ed. 54 (38), 11283-11288 (2015).</li><li>Thiele, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Smallest+molecular+chalcogenidometalate+anions+of+the+heaviest+metals:+syntheses,+structures,+and+their+interconversion.">Smallest molecular chalcogenidometalate anions of the heaviest metals: syntheses, structures, and their interconversion.</a> Dalton Trans. , (2016).</li><li>Thiele, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Solvothermal+and+ionothermal+synthses+and+structures+of+amine-+and/or+(poly-)chalcogenide+coordinated+metal+complexes.">Solvothermal and ionothermal synthses and structures of amine- and/or (poly-)chalcogenide coordinated metal complexes.</a> Z. Kristallogr. 229 (7), 489-495 (2014).</li><li>Thiele, G., Vondung, L., Donsbach, C., Pulz, S., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Organic+Cation+and+Complex+Cation-Stabilized+(Poly-)Selenides,+[Cation]x(Sey)z:+Diversity+in+Structures+and+Properties.">Organic Cation and Complex Cation-Stabilized (Poly-)Selenides, [Cation]x(Sey)z: Diversity in Structures and Properties.</a> Z. Anorg. Allg. Chem. 640 (14), 2684-2700 (2014).</li><li>Thiele, G., Lichtenberger, N., Tonner, R., Dehnen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Syntheses,+Structures+and+Electronic+Properties+of+a+New+Series+of+Tellurides+of+the+Type+[Sequestrated+Cation]2[Tex]+(x+=+1-4).">Syntheses, Structures and Electronic Properties of a New Series of Tellurides of the Type [Sequestrated Cation]2[Tex] (x = 1-4).</a> Z. Anorg. Allg. Chem. 639 (15), 2809-2815 (2013).</li></ol>

The authors have nothing to disclose.

The combination of classical high-temperature, solid-state reactions with solution-based methods allows for the generation and isolation of novel compounds that cannot be synthesized by only one of these pathways. Even though, in most cases, a clear identification and full characterization of the intermediate species is difficult or essentially impossible, the general idea is straightforward and can be applied to a variety of elemental combinations. Furthermore, the actual synthetic conditions for the generation of one s...

Metal chalcogenides, such as SnSe or CuInSe, are versatile materials with a wide range of applications, for instance, as semiconductor, thermoelectric, or nonlinear optic materials1-6. Similar elemental compositions are found within chalcogenidometalates, where the metal is in a formally positive oxidation state and coordinated by negative (poly-)chalcogenide ligands to yield an overall anionic species. Different from the abovementioned materials, such metalates are additionally comprised of counter-ions, which are well separated from the anionic substructure. Typical cations are (solvated) alkali or alkaline earth metals, ammonium, or phosphonium ions. Most often, such salts with chalcogenidometalate anions have physical properties that are similar to their parental binary or ternary compounds, such as similar band gaps or photo- and semiconductivity properties. However, due to the broad range of possible anionic architectures within each elemental combination, ranging from isolated molecular species through strands and sheets of interconnected anions to extended three-dimensional frameworks, an even finer tuning of various properties can be achieved, ultimately aiming at the designed synthesis of compounds with the desired properties. Within the concept of dimensional reduction, it has been shown that a relative increase of counter ions per formula unit, which accompanies a reduction from 3D via 2D and 1D to 0D anionic architectures (0D representing molecular species), decreases the observed band gap7. Moreover, by the utilization of different (or mixtures of) chalcogenide ligands, it is even possible to achieve an ultra-fine adjustment of the band gap8,9.
Apart from these practical applications and visionary relevancies, chalcogenidometalates are still investigated for fundamental understanding, such as for the generation of novel anionic structure types or the discovery and interpretation of an unusual bonding, as well as for their unprecedented properties. Whereas the lighter congeners (i.e., oxidometalates, commonly referred to as oxometalates) have been extensively studied, in particular for potential catalytic applications, the heavier chalcogenidometalates are far less explored.
Our own interest has been focused on the synthesis, properties, and further reactivity of chalcogenidotetrelates (i.e., the heavier homologs of silicates)10,11. There is a broad variety of such compounds, ranging from water-stable and soluble binary anions, such as the [SnTe4]4- anion12; to organic, functionalized, and multinary cluster compounds, such as {[Ir3(cod)3(&#181;3-S)2](&#181;3-S)SnCl}2 (cod = cycloocta-1,5-diene)13. Our most recent studies deal with chalcogenidoplumbates, with lead as the central metal atom(s). In line with the inert-pair concept for heavy atoms, addressing the stabilization of the 6s orbital due to relativistic effects, lead is usually observed in the formal +II oxidation state. Exceptions like PbO2 are strong oxidizing agents, and the heavier lead(IV) chalcogenides, &#34;PbCh2,&#34; have not been discovered to date14. The same holds for the chalcogenidoplumbate(IV) anions, of which only [PbO4]4- has been reported15 until recently (see below).
Apart from a diverse group of structurally investigated oxidoplumbates(II,IV), there have been only few examples of chalcogenidoplumbates(II), namely [PbTe3]4-, with a trigonal pyramidal anion16; and [Pb2Ch3]2-, where Ch = Se or Te, with a trigonal bipyramidal anion17. These are synthesized by a route that has also been applied for the generation of Zintl ions18. Upon preparation of multinary intermetallic phases by fusion of the elements at high temperatures, subsequent extraction by solvents in the presence of a sequestering agent affords the desired products in (single-)crystalline form. In the case of the [Pb2Ch3]2- anions, for instance, a phase of the nominal composition &#34;KPbCh&#34; has been extracted with 1,2-diaminoethane (en) in the presence of 4,7,13,16,21,24-Hexaoxa-1,10-diazabicyclo[8.8.8]hexacosane ([2.2.2]crypt). The cryptand is necessary both for crystallization upon increase of the effective cation radius in the {K[2.2.2]crypt}+ complex counter ion, to better match the anionic size, and for a shielding of the positive charge that suppresses an electron back-donation from the anion in solution. Such salts with encapsulated cations usually reveal high tendencies for crystallization and thus, fairly good yields when compared to the corresponding salts without sequestration agents. However, a rather cumbersome synthesis or the high prices of cryptands prevent the excessive scaling of such approaches.
In contrast, K4[PbTe3]&#183;2en is synthesized via in situ reduction in solution, as has already been used as early as 1891 for the generation of the famous Pb94- anion19,20. For the latter, elemental alkaline metals were added to suspensions of lead in liquid ammonia at low temperatures, whereas for the telluridoplumbate, an alloy of the nominal composition &#34;PbTe2&#34; was reduced at room temperature, again by the addition of elemental potassium.
Our first approach towards such metalate species to be presented herein is a combination of both pathways. Here, solid-state synthesis is followed by either reduction in solution in the presence of inexpensive sequestering agents, such as 1,4,7,10,13,16-hexaoxacyclooctadecane (18-crown-6), or via reduction with alkaline metals that are chelated by the solvent itself, without the need for additional sequestering agents, similar to the synthesis of [Na4(en)7][Sn9]21. Our second approach also starts with high-temperature synthesis, but it is followed by solvothermal extraction of the resulting phases (i.e., extraction at elevated temperatures and pressures)22. In the following, we will present both synthetic approaches and some of our recent results upon application of these reaction pathways.

<table><tbody><tr><td>Ethan-1,2-diamine</td><td>Sigma-Aldrich</td><td>E26266-2.5L</td><td></td></tr><tr><td>Calcium hydride</td><td>Sigma-Aldrich</td><td>213268-100G</td><td></td></tr><tr><td>Tetrahydrofuran</td><td>Sigma-Aldrich</td><td>401757-1L</td><td></td></tr><tr><td>Sodium</td><td>Sigma-Aldrich</td><td>71172-1KG</td><td></td></tr><tr><td>Potassium</td><td>Sigma-Aldrich</td><td>244864-50G</td><td></td></tr><tr><td>Tris-triphenylphosphine rhodium chloride</td><td>Sigma-Aldrich</td><td>199982-5G</td><td></td></tr><tr><td>Lead</td><td>Acros</td><td>222625000</td><td></td></tr><tr><td>Selenium</td><td>Sigma-Aldrich</td><td>209643-50G</td><td></td></tr><tr><td>18-crown-6</td><td>Acros</td><td>181561000</td><td></td></tr></tbody></table>

combining solid-state and solution-based techniques: synthesis and reactivity of chalcogenidoplumbates(ii or iv)

The phases of &#34;PbCh2&#34; (Ch = Se, Te) are obtained from solid-state syntheses (i.e., by the fusion of the elements under inert conditions in silica glass ampules). Reduction of such phases by elemental alkaline metals in amines affords crystalline chalcogenidoplumbate(II) salts comprised of [PbTe3]2- or [Pb2Ch3]2- anions, depending upon which sequestering agent for the cations is present: crown ethers, like 18-crown-6, or cryptands, like [2.2.2]crypt. Reactions of solutions of such anions with transition-metal compounds yield (poly-)chalcogenide anions or transition-metal chalcogenide clusters, including one with a &#181;-PbSe ligand (i.e., the heaviest-known CO homolog).
In contrast, the solid-state synthesis of a phase of the nominal composition &#34;K2PbSe2&#34; by successive reactions of the elements and by the subsequent solvothermal treatment in amines yields the first non-oxide/halide inorganic lead(IV) compound: a salt of the ortho-selenidoplumbate(IV) anion [PbSe4]4-. This was unexpected due to the redox potentials of Pb(IV) and Se(-II). Such methods can further be applied to other elemental combinations, leading to the formation of solutions with binary [HgTe2]2- or [BiSe3]3- anions, or to large-scale syntheses of K2Hg2Se3 or K3BiSe3 via the solid-state route.
All compounds are characterized by single-crystal X-ray diffraction and elemental analysis; solutions of plumbate salts can be investigated by 205Pb and 77Se or 127Te NMR techniques. Quantum chemical calculations using density functional theory methods enable energy comparisons. They further allow for insights into the electronic configuration and thus, the bonding situation. Molecular Rh-containing Chevrel-type compounds were found to exhibit delocalized mixed valence, whereas similar telluridopalladate anions are electron-precise; the cluster with the &#181;-PbSe ligand is energetically favored over a hypothetical CO analog, in line with the unsuccessful attempt at its synthesis. The stability of formal Pb(IV) within the [PbSe4]4- anion is mainly due to a suitable stabilization within the crystal lattice.

The existence of an ortho-selenidoplumbate anion [PbSe4]4-23 (see Figure 1, top right) has been confirmed by single crystal diffraction experiments, elemental analysis, and quantum chemical calculations. The crystal structure refinement confirms the almost-perfect tetrahedral coordination geometry, as would be expected for a lead(IV) ion, whereas DFT calculations rationalize the energetically stabilized a1...

Watch this Scientific Journal Video about Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of ChalcogenidoplumbatesII or IV at JoVE.com

Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of ChalcogenidoplumbatesII or IV

The synthesis of chalcogenidoplumbates(II,IV) via the in situ reduction of nominal "PbCh2" (Ch = Chalcogen) and via a solid-state reaction and subsequent solvothermal reactions is presented. Additionally, reactivities of plumbate(II) solutions are portrayed, which yield the heaviest-known CO homolog known to date: the &#181;-PbSe ligand.

Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of Chalcogenidoplumbates(II or IV)

The phases of &#34;PbCh2&#34; (Ch = Se, Te) are obtained from solid-state syntheses (i.e., by the fusion of the elements under inert conditions in silica ...

combining-solid-state-solution-based-techniques-synthesis-reactivity

Research

JoVE Journal

Chemistry

10.6K Views.  University of California, Berkeley. The synthesis of chalcogenidoplumbates(II,IV) via the in situ reduction of nominal "PbCh2" (Ch = Chalcogen) and via a solid-state reaction and subsequent solvothermal reactions is presented. Additionally, reactivities of plumbate(II) solutions are portrayed, which yield the heaviest-known CO homolog known to date: the µ-PbSe ligand. 

Video: Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of ChalcogenidoplumbatesII or IV

Activating Molecules, Ions, and Solid Particles with Acoustic Cavitation

The chemical and physical effects of ultrasound arise not from a direct interaction of molecules with sound waves, but rather from the acoustic cavitation: the nucleation, growth, and implosive collapse of microbubbles in liquids submitted to power ultrasound. The violent implosion of bubbles leads to the formation of chemically reactive species and to the emission of light, named sonoluminescence. In this manuscript, we describe the techniques allowing study of extreme intrabubble conditions and chemical reactivity of acoustic cavitation in solutions. The analysis of sonoluminescence spectra of water sparged with noble gases provides evidence for nonequilibrium plasma formation. The photons and the "hot" particles generated by cavitation bubbles enable to excite the non-volatile species in solutions increasing their chemical reactivity. For example the mechanism of ultrabright sonoluminescence of uranyl ions in acidic solutions varies with uranium concentration: sonophotoluminescence dominates in diluted solutions, and collisional excitation contributes at higher uranium concentration. Secondary sonochemical products may arise from chemically active species that are formed inside the bubble, but then diffuse into the liquid phase and react with solution precursors to form a variety of products. For instance, the sonochemical reduction of Pt(IV) in pure water provides an innovative synthetic route for monodispersed nanoparticles of metallic platinum without any templates or capping agents. Many studies reveal the advantages of ultrasound to activate the divided solids. In general, the mechanical effects of ultrasound strongly contribute in heterogeneous systems in addition to chemical effects. In particular, the sonolysis of PuO2 powder in pure water yields stable colloids of plutonium due to both effects.

Acoustic cavitation in liquids submitted to power ultrasound creates transient extreme conditions inside the collapsing bubbles, which are the origin of unusual chemical reactivity and light emission, known as sonoluminescence. In the presence of noble gases, nonequilibrium plasma is formed. The "hot" particles and the photons generated by collapsing bubbles are able to excite species in solution.

The chemical and physical effects of ultrasound arise not from a direct interaction of molecules with sound waves, but rather from the acoustic ...

The Synthesis of [Sn10(Si(SiMe3)3)4]2- Using a Metastable Sn(I) Halide Solution Synthesized via a Co-condensation Technique

The number of well-characterized metalloid tin clusters, synthesized by applying the disproportionation of a metastable Sn(I) halide in the presence of a sterically demanding ligand, has increased in recent years. The metastable Sn(I) halide is synthesized at&#160;&#34;outer space conditions&#34; via the preparative co-condensation technique. Thereby, the subhalide is synthesized in an oven at high temperatures, around 1,300 &#176;C, and at reduced pressure by the reaction of elemental tin with hydrogen halide gas (e.g., HCl). The subhalide (e.g., SnCl) is trapped within a matrix of an inert solvent, like toluene at -196 &#176;C. Heating the solid matrix to -78 &#176;C gives a metastable solution of the subhalide. The metastable subhalide solution is highly reactive but can be stored at -78 &#176;C for several weeks. On heating the solution to room temperature, a disproportionation reaction occurs, leading to elemental tin and the corresponding dihalide. By applying bulky ligands like Si(SiMe3)3, the intermediate metalloid cluster compounds can be trapped before complete disproportionation to elemental tin. Hence, the reaction of a metastable Sn(I)Cl solution with Li-Si(SiMe3)3 gives [Sn10(Si(SiMe3)3)4]2- 1 as black crystals in high yield. 1 is formed via a complex reaction sequence including salt metathesis, disproportionation, and degradation of larger clusters. Further, 1 can be analyzed by various methods like NMR or single crystal X-ray structure analysis.

The Synthesis of [Sn10SiSiMe334]2- Using a Metastable SnI Halide Solution Synthesized via a Co-condensation Technique

The disproportionation reaction of a metastable Sn(I) chloride solution, obtained via the preparative co-condensation technique, is used for the synthesis of a metalloid tin cluster compound.

The number of well-characterized metalloid tin clusters, synthesized by applying the disproportionation of a metastable Sn(I) halide in the presence of a ...

A Protocol for Safe Lithiation Reactions Using Organolithium Reagents

Organolithium reagents are powerful tools in the synthetic chemist&#39;s toolbox. However, the extreme pyrophoric nature of the most reactive reagents warrants proper technique, thorough training, and proper personal protective equipment. To aid in the training of researchers using organolithium reagents, a thorough, step-by-step protocol for the safe and effective use of tert-butyllithium on an inert gas line or within a glovebox is described. As a model reaction, preparation of lithium tert-butyl amide by the reaction of tert-butyl amine with one equivalent of tert-butyl lithium is presented.

The safe and proper use of organolithium reagents is described.

Organolithium reagents are powerful tools in the synthetic chemist&#39;s toolbox. However, the extreme pyrophoric nature of the most reactive reagents ...

Preparation and Reactivity of a Triphosphenium Bromide Salt: A Convenient and Stable Source of Phosphorus(I)

We present herein the optimized synthesis of a triphosphenium bromide salt. Apart from being a versatile metathesis reagent, this unusually stable low-valent-phosphorus-containing compound acts as a useful P+ transfer agent. Unlike traditional methods employed to access low-coordinate phosphorus species which usually require pyrophoric phosphorus-containing precursors (white phosphorus, Tris(trimethylsilyl)phosphine, etc.), or harsh reducing agents (alkali metals, potassium graphite, etc.), the current approach does not involve pyrophoric or explosive reagents and can be done on large scales (&#62;20 g) in excellent yields by undergraduates with basic air-free synthetic training. The bromide counter ion is readily exchanged with other anions such as tetraphenyl borate (described herein) using typical salt metathesis reagents to obtain materials with desired properties and reactivities. The versatility of this P+ transfer approach is exemplified by the reactions of these triphosphenium precursors with an N-heterocyclic carbene and an anionic bisphosphine, each of which readily displace the neutral bisphosphine to give an NHC-stabilized phosphorus(I) cation and a phosphorus(I) containing zwitterion, respectively.

Preparation and Reactivity of a Triphosphenium Bromide Salt: A Convenient and Stable Source of PhosphorusI

The synthesis of a triphosphenium bromide salt is described and its use as a P+ transfer agent is outlined by reactions with an N-heterocyclic carbene and an anionic bisphosphine, yielding an NHC-stabilized P(I) cation and a P(I) containing zwitterion, respectively.

We present herein the optimized synthesis of a triphosphenium bromide salt. Apart from being a versatile metathesis reagent, this unusually stable ...

Synthesis of a Thiol Building Block for the Crystallization of a Semiconducting Gyroidal Metal-sulfur Framework

We present a method for preparing thioester molecules as the masked form of the thiol linkers and their utilization for accessing a semiconducting and porous metal-dithiolene network in the highly ordered single crystalline state. Unlike the highly reactive free-standing thiols, which tend to decompose and complicate the crystallization of metal-thiolate open frameworks, the thioester reacts in situ to provide the thiol species, serving to mitigate the reaction between the mercaptan units and the metal centers, and to improve crystallization consequently. Specifically, the thioester was synthesized in a one-pot procedure: an aromatic bromide (hexabromotriphenylene) reacted with excess sodium thiomethoxide under vigorous conditions to first form the thioether intermediate product. The thioether was then demethylated by the excess thiomethoxide to provide the thiolate anion that was acylated to form the thioester product. The thioester was conveniently purified by standard column chromatography, and then used directly in the framework synthesis, wherein NaOH and ethylenediamine serve to revert in situ the thioester to the thiol linker for assembling the single-crystalline Pb(II)-dithiolene network. Compared with other methods for thiol synthesis (e.g., by cleaving alkyl thioether using sodium metal and liquid ammonia), the thioester synthesis here uses simple conditions and economical reagents. Moreover, the thioester product is stable and can be conveniently handled and stored. More importantly, in contrast to the generic difficulty in accessing crystalline metal-thiolate open frameworks, we demonstrate that using the thioester for in situ formation of the thiol linker greatly improves the crystallinity of the solid-state product. We intend to encourage broader research efforts on the technologically important metal-sulfur frameworks by disclosing the synthetic protocol for the thioester as well as the crystalline framework solid.

Here, we present a one-pot, transition-metal-free synthesis of thiols and thioesters from aromatic halides and sodium thiomethoxide, followed by the preparation of single crystals of a metal-dithiolene network using thiol species generated in situ from the more stable and tractable thioester.

We present a method for preparing thioester molecules as the masked form of the thiol linkers and their utilization for accessing a semiconducting and ...

Synthesis of Bimetallic Pt/Sn-based Nanoparticles in Ionic Liquids

We demonstrate a method for the synthesis of bimetallic nanoparticles consisting of Pt and Sn. A synthesis strategy is used in which the particular physico-chemical properties of ionic liquids (ILs) are exploited to control both nucleation and growth processes. The nanoparticles form colloidal sols of very high colloidal stability in the IL, which is particularly interesting in view of their use as quasi-homogeneous catalysts. Procedures for both nanoparticle extraction in conventional solvents and for nanoparticle precipitation are presented. The size, structure and composition of the synthesized nanocrystals are confirmed using inductively coupled plasma atomic emission spectroscopy (ICP-AES), X-ray diffraction analysis (XRD) and transmission electron microscopy (TEM) with energy-dispersive X-ray spectroscopy (EDX). By this, we show that the nanocrystals are random-type alloy and of small (2-3 nm) size. The catalytic activity and selectivity in the hydrogenation of &#945;,&#946;-unsaturated aldehydes is tested in a semi-continuous batch-type reactor. In this context, the bimetallic Pt/Sn-based nanoparticles reveal a high selectivity towards the unsaturated alcohol.

A protocol for the synthesis of bimetallic nanoparticles in ionic liquids and the procedure of their catalytic testing in the selective hydrogenation of unsaturated aldehydes are described.

We demonstrate a method for the synthesis of bimetallic nanoparticles consisting of Pt and Sn. A synthesis strategy is used in which the particular ...

Facile Synthesis of Colloidal Lead Halide Perovskite Nanoplatelets via Ligand-Assisted Reprecipitation

In this work, we demonstrate a facile method for colloidal lead halide perovskite nanoplatelet synthesis (Chemical formula: L2[ABX3]n-1BX4, L: butylammonium and octylammonium, A: methylammonium or formamidinium, B: lead, X: bromide and iodide, n: number of [BX6]4- octahedral layers in the direction of nanoplatelet thickness) via ligand-assisted reprecipitation. Individual perovskite precursor solutions are prepared by dissolving each nanoplatelet constituent salt in N,N-dimethylformamide (DMF), which is a polar organic solvent, and then mixing in specific ratios for targeted nanoplatelet thickness and composition. Once the mixed precursor solution is dropped into nonpolar toluene, the abrupt change in the solubility induces the instantaneous crystallization of nanoplatelets with surface-bound alkylammonium halide ligands providing colloidal stability. Photoluminescence and absorption spectra reveal emissive and strongly quantum-confined features. X-ray diffraction and transmission electron microscopy confirm the two-dimensional structure of the nanoplatelets. Furthermore, we demonstrate that the band gap of perovskite nanoplatelets can be continuously tuned in the visible range by varying the stoichiometry of the halide ion(s). Lastly, we demonstrate the flexibility of the ligand-assisted reprecipitation method by introducing multiple species as surface-capping ligands. This methodology represents a simple procedure for preparing dispersions of emissive 2D colloidal semiconductors.

This work demonstrates facile room-temperature synthesis of colloidal quantum-confined lead halide perovskite nanoplatelets by ligand-assisted reprecipitation method. Synthesized nanoplatelets show spectrally narrow optical features and continuous spectral tunability throughout the visible range by varying the composition and thicknesses.

In this work, we demonstrate a facile method for colloidal lead halide perovskite nanoplatelet synthesis (Chemical formula: L2[ABX3]n-1BX4, L: ...

Metal Oxide Heterojunction for Photocatalytic Activities

There is a significant global demand for improvements in synthesis techniques and their optimal characteristics, especially for industrial-scale applications. Sol-gel-based solution combustion synthesis (SG-SCS) is a simple method to produce ordered porous materials. In this regard, Pearson&#39;s hard and soft acids and bases theory assists in selecting host-dopant reactivity to form a proper heterojunction.
The formation of a heterojunction also changes the essential properties of the materials, improving photocatalysis via charge transfer or synergistic activities. A calcination temperature of 500 &#176;C is ideal for this process based on the results of the stability assessment via a differential thermogravimetry ratio analysis (DTG).
The nanoscale dimensions of the nanoparticles (NPs) and nanocomposites (NCs) generated were validated using X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). Furthermore, the scanning electron microscopy micrographs and BET analyses confirmed the porosity nature of the materials. HRTEM, X-ray photoelectron spectroscopy, and energy-dispersive X-ray investigations established the materials composition. The study found that NCs degraded the acid orange 8 (AO8) color more efficiently than bare ZnO.

The development of a heterojunction boosts the photocatalytic activities of solution combustion synthesis, which is a time-/energy-efficient process. Advanced analytical characterization techniques were used in this protocol to evaluate the materials&#39; characteristics, and nanocomposites demonstrated improved acid orange-8 dye degradation.

There is a significant global demand for improvements in synthesis techniques and their optimal characteristics, especially for industrial-scale ...

Synthesis of Low-Valent MOFs from Multitopic Phosphine Linkers

Experimental Approaches for the Synthesis of Low-Valent Metal-Organic Frameworks from Multitopic Phosphine Linkers

Metal-organic frameworks (MOFs) are the subject of intense research focus due to their potential applications in gas storage and separation, biomedicine, energy, and catalysis. Recently, low-valent MOFs (LVMOFs) have been explored for their potential use as heterogeneous catalysts, and multitopic phosphine linkers have been shown to be a useful building block for the formation of LVMOFs. However, the synthesis of LVMOFs using phosphine linkers requires conditions that are distinct from those in the majority of the MOF synthetic literature, including the exclusion of air and water and the use of unconventional modulators and solvents, making it somewhat more challenging to access these materials. This work serves as a general tutorial for the synthesis of LVMOFs with phosphine linkers, including information on the following: 1) the judicious choice of the metal precursor, modulator, and solvent; 2) the experimental procedures, air-free techniques, and required equipment; 3) the proper storage and handling of the resultant LVMOFs; and 4) useful characterization methods for these materials. The intention of this report is to lower the barrier to this new subfield of MOF research and facilitate advancements toward novel catalytic materials.

Author Spotlight: Experimental Approaches for the Synthesis of Low-Valent Metal-Organic Frameworks from Multitopic Phosphine Linkers  

Here, we describe a protocol for the synthesis of low-valent metal-organic frameworks (LVMOFs) from low-valent metals and multitopic phosphine linkers under air-free conditions. The resulting materials have potential applications as heterogeneous catalyst mimics of low-valent metal-based homogeneous catalysts.

Metal-organic frameworks (MOFs) are the subject of intense research focus due to their potential applications in gas storage and separation, biomedicine, ...

Synthesis and Discovery of Phosphonate-Based MOFs: A Solvothermal Approach

Discovery and Synthesis Optimization of Isoreticular Al(III) Phosphonate-Based Metal-Organic Framework Compounds Using High-Throughput Methods

High-throughput (HT) methods are an important tool for the fast and efficient screening of synthesis parameters and the discovery of new materials. This manuscript describes the synthesis of metal-organic frameworks (MOFs) from solution using an HT reactor system, resulting in the discovery of various phosphonate-based MOFs of the composition [Al2H12-x(PMP)3]Clx&#8729;6H2O (H4PMP = N,N &#39;-piperazine bis(methylenephosphonic acid)) for x = 4, 6, denoted as Al-CAU-60-xHCl, containing trivalent aluminum ions. This was accomplished under solvothermal reaction conditions by systematically screening the impact of the molar ratio of the linker to the metal and the pH of the reaction mixture on the product formation. The protocol for the HT investigation includes six steps: a) synthesis planning (DOE = design of&#160;experiment) within the HT methodology, b) dosing and working with in-house developed HT reactors, c) solvothermal synthesis, d) synthesis workup using in-house developed filtration blocks, e) characterization by HT powder X-ray diffraction, and f) evaluation of the data. The HT methodology was first used to study the influence of acidity on the product formation, leading to the discovery of Al-CAU-60&#8729;xHCl (x = 4 or 6).

Author Spotlight: Accelerating Discovery in Microporous Material Chemistry 

The targeted synthesis of new metal-organic frameworks (MOFs) is difficult, and their discovery depends on the knowledge and creativity of the chemist. High-throughput methods allow complex synthetic parameter fields to be explored quickly and efficiently, accelerating the process of finding crystalline compounds and identifying synthetic and structural trends.

High-throughput (HT) methods are an important tool for the fast and efficient screening of synthesis parameters and the discovery of new materials. This ...