This work was supported by an APART grant of the Austrian Academy of Sciences (CTH), the Technology Agency of the Czech Republic project no. TA04010877 (CTH, VH and JGS), and the Czech Science Foundation (GACR) project no GA16-01246S (to JGS). We thank W. Tecumseh Fitch for his suggestion to use denture fixative cream, and Ing. P. Liska from the Czech Army Forest Service for his help in acquiring the excised deer larynges.

The animal specimens analyzed in this paper were treated in accordance with the standard ethical requirements of the Palacky University in Olomouc, Czech Republic. They stem from red deer living wildly in forests, which were hunted by the Czech Army Forest Service during a regular hunting season.
1. Preparation of the Hemi-larynx Specimen
Note: Only properly prepared specimens should be used, as indicated in4 . Quick freezing of the larynx25 immediately after excision and storage at -80 &#176;C minimizes the potential of tissue degradation and alteration of biomechanical properties, and allows performing the experiments at any convenient time.
<ol>
	<li>Defrosting the larynx
	<ol>
		<li>Insert the frozen larynx into two autoclave bags or any other plastic bags with waterproof sealing. Seal the bags and put them into a water bath heated to 30 &#176;C until the larynx is completely defrosted. The duration required ranges from a few hours to more than a day, depending on larynx size and freezing temperature.</li>
	</ol>
	</li>
	<li>Cleaning the larynx
	<ol>
		<li>After the larynx is defrosted, remove it from the bag and clean it thoroughly with saline solution (0.9% NaCl).</li>
		<li>Carefully remove superfluous tissue as applicable (i.e. external neck muscles, hyoid bone etc.) without damaging the main laryngeal structures, and shorten the trachea to a length adequate for mounting the larynx onto an air supply tube (usually ca. 4-5 cm).</li>
		<li>Check the laryngeal tissue for potential tissue anomalies, such as wounds, organic deformations, or cracks potentially occurring from the freezing process, which could make the larynx unsuitable for the experiment.</li>
	</ol>
	</li>
	<li>Exposure of the thyroid and cricoid cartilages
	<ol>
		<li>Remove parts of the external laryngeal muscle tissue around the thyroid and cricoid cartilage using a scalpel, thus exposing the cartilages in preparation for the mid-sagittal cut creating the hemi-larynx. This preparation stage is depicted in Figure 1A and 1B.</li>
	</ol>
	</li>
	<li>Mid-sagittal cut through the thyroid cartilage
	<ol>
		<li>Make an initial vertical cut through the anterior part of the thyroid cartilage.</li>
		<li>Carefully place the cut slightly more onto the side that is about to be removed, in order not to damage the vocal fold that needs to remain preserved. If possible, use a scalpel for cutting. If the cartilage is ossified, use a small saw.</li>
	</ol>
	</li>
	<li>Cutting the cricoid cartilage
	<ol>
		<li>Lead the cut vertically (inferiorly) from in between the arytenoid cartilages and then through the cricoid cartilage to an approximately horizontal level of the inferior thyroid notch.</li>
	</ol>
	</li>
	<li>Removal of one vocal fold, creating an L-shaped incision in the larynx
	<ol>
		<li>Make a horizontal cut starting from the inferior end of the previously made vertical cut in the cricoid cartilage, and lead the new cut towards the inferior thyroid notch. Anteriorly fold the side of the larynx that is going to be removed.</li>
		<li>Make a vertical cut through the soft tissue on the inner side of the thyroid cartilage - be careful while leading the cut in between the anterior attachment of the vocal folds to the thyroid cartilage, thus avoiding damage to the vocal fold.</li>
	</ol>
	</li>
	<li>Refinement of the cut through the thyroid cartilage
	<ol>
		<li>Use a scalpel, a saw, or a file, in order to apply a precisely straight cut in the thyroid cartilage, and get as close as possible to the anterior part of the previously inspected vocal fold.</li>
		<li>Remove also a small part of the posterior thyroid cartilage, in order to create space for inserting the prong for adducting the arytenoid cartilage and thus the vocal fold (see below). This preparation stage is depicted in Figure 1C and 1D. 
		Note: Depending on the research question, full exposition of the whole vocal fold may be needed to enable its visibility from above. In such a case, the structures above the (true) vocal fold (i.e., the ventricular or vestibular fold, as applicable given the anatomy of the specimen) should be removed. In some specimens the inner soft laryngeal tissue above the vocal folds might lose its connection with the thyroid cartilage and interferes with the vocal fold during vibration, potentially causing spurious (mostly irregular) oscillatory patterns. In such a case careful removal of that tissue is inevitable.</li>
	</ol>
	</li>
</ol>
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/55303/55303fig1.jpg" /> 
Figure 1: Hemi-larynx preparation and mounting. (A) and (B) Cleaned larynx specimen, medial and posterior view, before removal of left vocal fold; (C) and (D) Prepared hemi-larynx with L-shaped incision (left vocal fold removed), medial and posterior view. <a href="//cloudfront.jove.com/files/ftp_upload/55303/55303fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

2. Hemi-larynx Experiment
<ol>
	<li>Hemi-laryngeal setup
	<ol>
		<li>Use an air-supply tube which delivers warmed and humidified air into the larynx.</li>
		<li>Construct two perpendicularly arranged transparent plates as a substitution for removed laryngeal parts.</li>
		<li>Use prongs 4 for increasing the stability of the larynx and creating a proper pre-phonatory larynx configuration by adducting the remaining vocal fold to the vertical glass plate (see Figure 2A). 
		Note: Theoretically, the vocal folds might also be adducted by sutures and weights on a pulley-lever system 26 . However, such an approach has, to the best knowledge of these authors, not yet been attempted for a hemilarynx preparation.</li>
	</ol>
	</li>
</ol>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/55303/55303fig2.jpg" />
Figure 2: Hemi-larynx setup. (A) Supporting structures: air supply tube, L-shaped glass plate arrangement, adduction prongs. (B) Mounted hemi-larynx preparation with adduction prongs. (C) and (D) Close-ups of hemi-larynx-preparation, viewed from the side and from the top, respectively. <a href="//cloudfront.jove.com/files/ftp_upload/55303/55303fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="2">
	<li>Mounting the hemi-larynx
	<ol>
		<li>Cover the air supply tube with denture fixative cream and mount the larynx using the remaining part of its trachea. The fixative cream works as an adhesive and closes potential gaps, thus creating an air-tight seal.</li>
		<li>Fasten the trachea with a plastic tightening strap or a hose clamp.&#160;</li>
		<li>Also cover the edges of the cut through the thyroid cartilage with the fixative cream, while avoiding spreading fixative cream on the vocal fold or the inner soft laryngeal tissues.</li>
		<li>Attach the transparent plates.</li>
	</ol>
	</li>
	<li>Stabilization of the thyroid cartilage, adduction of the vocal fold using prongs
	<ol>
		<li>Use the prongs to adduct the vocal fold to the plate and stabilize the thyroid cartilage.</li>
		<li>After the fixative cream has set, apply the airflow in order to establish vocal fold oscillation and check for possible leaks between the hemi-larynx and the glass plates.</li>
		<li>Seal eventually occurring gaps by adding more fixative cream.</li>
	</ol>
	</li>
</ol>

<ol><li>Story, B. H. <a target="_blank" href="http://u.arizona.edu/~bstory/story_asj.pdf">An overview of the physiology, physics and modeling of the sound source for vowels.</a> Acoust Sci Technol. 23 (4), 195-206 (2002).</li>
<li>Titze, I. R. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aTitze%2C+IR+%22Principles+of+voice+production+%28second+printing%29%22">Principles of voice production (second printing)</a>. , National Center for Voice and Speech. Iowa City, IA. (2000).</li>
<li>Cooper, D. S. Ch. 95. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aCooper%2C+DS+%22Otolaryngology+-+head+and+neck+surgery%22">Otolaryngology - head and neck surgery</a>. Cummings, C. W., Fredrickson, J. M., Harker, L. A., Schuller, D. E., Krause, C. J. 3, C. V. Mosby. St. Louis and Toronto. 1728-1737 (1986).</li>
<li>Titze, I. R. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aTitze%2C+IR+%22The+myoelastic+aerodynamic+theory+of+phonation%22">The myoelastic aerodynamic theory of phonation</a>. Titze, I. R. , National Center for Voice and Speech. Denver CO and Iowa City IA. 1-62 (2006).</li>
<li>Baer, T. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=%22Investigation+of+phonation+using+excised+larynxes+%28Doctoral+%29%22">Investigation of phonation using excised larynxes (Doctoral dissertation)</a>. , Massachusetts Institute of Technology. Cambridge, Mass. (1975).</li>
<li>Bless, D. M., Patel, R. R., Connor, N. Ch. 11. <a target="_blank" href="https://www.abebooks.com/Larynx-Third-Edition-Volume-1-2/18793288853/bd">The Larynx</a>. Fried, M. P., Ferlito, A. I, Third Edition, Plural Publishing. San Diego, CA. 181-210 (2009).</li>
<li>Berke, G. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Laryngeal+modeling%3A+theoretical%2C+in+vitro%2C+in+vivo%5BTitle%5D)+AND+%22Laryngoscope%22%5BJournal%5D)">Laryngeal modeling: theoretical, in vitro, in vivo.</a> Laryngoscope. 97, 871-881 (1987).</li>
<li>Scherer, R. C., Titze, I. R., Curtis, J. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Pressure-flow+relationships+in+two+models+of+the+larynx+having+rectangular+glottal+shapes%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Pressure-flow relationships in two models of the larynx having rectangular glottal shapes.</a> J Acoust Soc Am. 73 (2), 668-676 (1983).</li>
<li>Sidlof, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Geometry+of+human+vocal+folds+and+glottal+channel+for+mathematical+and+biomechanical+modeling+of+voice+production%5BTitle%5D)+AND+%22J+Biomech%22%5BJournal%5D)">Geometry of human vocal folds and glottal channel for mathematical and biomechanical modeling of voice production.</a> J Biomech. 41 (5), 985-995 (2008).</li>
<li>Scherer, R. C., Torkaman, S., Kuehn, D. P., Afjeh, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Intraglottal+pressures+in+a+three-dimensional+model+with+a+non-rectangular+glottal+shape%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Intraglottal pressures in a three-dimensional model with a non-rectangular glottal shape.</a> J Acoust Soc Am. 128 (2), 828-838 (2010).</li>
<li>Titze, I. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((The+physics+of+small-amplitude+oscillation+of+the+vocal+folds%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">The physics of small-amplitude oscillation of the vocal folds.</a> J Acoust Soc Am. 83 (4), 1536-1552 (1988).</li>
<li>Horacek, J., Svec, J. G. Ch. 2. Paidoussis, M. P. Proceedings of the 5th International Symposium on Fluid Structure Interaction, Aeroelasticity, Flow Induced Vibration and Noise (IMECE2002), Vol.3 ASME Int. Mechanical Engineering Congress, 17-22 November 2002, New Orleans, Louisiana, USA (CD-ROM)., New Orleans, Louisiana, USA, , 1043-1054 (2002).</li>
<li>Vilkman, E., Alku, P., Laukkanen, A. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Vocal-fold+collision+mass+as+a+differentiator+between+registers+in+the+low-pitch+range%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Vocal-fold collision mass as a differentiator between registers in the low-pitch range.</a> J Voice. 9 (1), 66-73 (1995).</li>
<li>Herbst, C. T., Svec, J. G. <a target="_blank" href="https://www.researchgate.net/publication/308353846_Adjustment_of_glottal_configurations_in_singing">Adjustment of glottal configurations in singing.</a> J Singing. 70 (3), 301-308 (2014).</li>
<li>Hiroto, I. <a target="_blank" href="NULL">Vibration of vocal cords: an ultra high-speed cinematographic study(Film)</a>. , Department of otolaryngology, Kurume University. Kurume, Japan. (1968).</li>
<li>Jiang, J. J., Titze, I. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+methodological+study+of+hemilaryngeal+phonation%5BTitle%5D)+AND+%22Laryngoscope%22%5BJournal%5D)">A methodological study of hemilaryngeal phonation.</a> Laryngoscope. 103 (8), 872-882 (1993).</li>
<li>Scherer, R. C., Druker, D. G., Titze, I. R. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aScherer%2C+RC+%22Vocal+physiology%3A+voice+production%2C+mechanisms+and+functions%22">Vocal physiology: voice production, mechanisms and functions</a>. Fujimura, O. , Raven Press. New York. 279-291 (1988).</li>
<li>Jiang, J. J., Titze, I. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Measurement+of+vocal+fold+intraglottal+pressure+and+impact+stress%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Measurement of vocal fold intraglottal pressure and impact stress.</a> J Voice. 8 (2), 132-144 (1994).</li>
<li>Alipour, F., Scherer, R. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Dynamic+glottal+pressures+in+an+excised+hemilarynx+model%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Dynamic glottal pressures in an excised hemilarynx model.</a> J Voice. 14 (4), 443-454 (2000).</li>
<li>Berry, D. A., Montequin, D. W., Tayama, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((High-speed+digital+imaging+of+the+medial+surface+of+the+vocal+folds%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">High-speed digital imaging of the medial surface of the vocal folds.</a> J Acoust Soc Am. 110 (5 Pt 1), 2539-2547 (2001).</li>
<li>Döllinger, M., Tayama, N., Berry, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Empirical+eigenfunctions+and+medial+surface+dynamics+of+a+human+vocal+fold%5BTitle%5D)+AND+%22Methods+Inf+Med%22%5BJournal%5D)">Empirical eigenfunctions and medial surface dynamics of a human vocal fold.</a> Methods Inf Med. 44 (3), 384-391 (2005).</li>
<li>Döllinger, M., Berry, D. A., Berke, G. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Medial+surface+dynamics+of+an+in+vivo+canine+vocal+fold+during+phonation%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Medial surface dynamics of an in vivo canine vocal fold during phonation.</a> J Acoust Soc Am. 117 (5), 3174-3183 (2005).</li>
<li>Döllinger, M., Berry, D. A., Kniesburges, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Dynamic+vocal+fold+parameters+with+changing+adduction+in+ex-vivo+hemilarynx+experiments%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Dynamic vocal fold parameters with changing adduction in ex-vivo hemilarynx experiments.</a> J Acoust Soc Am. 139 (5), 2372-2385 (2016).</li>
<li>Durham, P. L., Scherer, R. C., Druker, D. G., Titze, I. R. Development of excised larynx procedures for studying mechanisms of phonation. Technical report. , Voice Acoustics and Biomechanics Laboratory, Department of Speech Pathology and Audiology, The University of Iowa. (1987).</li>
<li>Chan, R. W., Titze, I. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Effect+of+postmortem+changes+and+freezing+on+the+viscoelastic+properties+of+vocal+fold+tissues%5BTitle%5D)+AND+%22Ann+Biomed+Eng%22%5BJournal%5D)">Effect of postmortem changes and freezing on the viscoelastic properties of vocal fold tissues.</a> Ann Biomed Eng. 31 (4), 482-491 (2003).</li>
<li>Berg van den, J. W., Tan, T. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Results+of+experiments+with+human+larynxes%5BTitle%5D)+AND+%22Practica+Oto-Rhino-Laryngologica%22%5BJournal%5D)">Results of experiments with human larynxes.</a> Practica Oto-Rhino-Laryngologica. 21, 425-450 (1959).</li>
<li>Hampala, V., Garcia, M., Svec, J. G., Scherer, R. C., Herbst, C. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Relationship+between+the+electroglottographic+signal+and+vocal+fold+contact+area%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Relationship between the electroglottographic signal and vocal fold contact area.</a> J Voice. 30 (2), 161-171 (2016).</li>
<li>Herbst, C. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Glottal+opening+and+closing+events+investigated+by+electroglottography+and+super-high-speed+video+recordings%5BTitle%5D)+AND+%22J+Exp+Biol%22%5BJournal%5D)">Glottal opening and closing events investigated by electroglottography and super-high-speed video recordings.</a> J Exp Biol. 217 (6), 955-963 (2014).</li>
<li>Zemlin, W. R. <a target="_blank" href="https://books.google.com/books/about/Speech_and_Hearing_Science.html?id=fNBqAAAAMAAJ">Speech and hearing science: Anatomy & physiology</a>. , 3, Prentice Hall. New Jersey. (1988).</li>
<li>Lohscheller, J., Toy, H., Rosanowski, F., Eysholdt, U., Döllinger, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Clinically+evaluated+procedure+for+the+reconstruction+of+vocal+fold+vibrations+from+endoscopic+digital+high-speed+videos%5BTitle%5D)+AND+%22Med.+Image+Anal%22%5BJournal%5D)">Clinically evaluated procedure for the reconstruction of vocal fold vibrations from endoscopic digital high-speed videos.</a> Med. Image Anal. 11 (4), 400-413 (2007).</li>
<li>Wittenberg, T., Moser, M., Tigges, M., Eysholdt, U. <a target="_blank" href="https://link.springer.com/article/10.1007/BF01213501">Recording, processing, and analysis of digital high-speed sequences in glottography.</a> Mach Vis Appl. 8 (6), 399-404 (1995).</li>
<li>Larsson, H., Hertegard, S., Lindestad, P. A., Hammarberg, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Vocal+fold+vibrations%3A+high-speed+imaging%2C+kymography%2C+and+acoustic+analysis%3A+a+preliminary+report%5BTitle%5D)+AND+%22Laryngoscope%22%5BJournal%5D)">Vocal fold vibrations: high-speed imaging, kymography, and acoustic analysis: a preliminary report.</a> Laryngoscope. 110 (12), 2117-2122 (2000).</li>
<li>Wittenberg, T., Tigges, M., Mergell, P., Eysholdt, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Functional+imaging+of+vocal+fold+vibration%3A+digital+multislice+high-speed+kymography%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Functional imaging of vocal fold vibration: digital multislice high-speed kymography.</a> J Voice. 14 (3), 422-442 (2000).</li>
<li>Deliyski, D., Petrushev, P. <a target="_blank" href="NULL">AQL 2003 Hamburg: Proceeding Papers for the Conference Advances in Quantitative Laryngology, Voice and Speech Research. (CD ROM)</a>. Schade, G., Müller, F., Wittenberg, T., Hess, M. , IRB Verlag. Stuttgart, Germany. 1-16 (2003).</li>
<li>Svec, J. G., Schutte, H. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Kymographic+imaging+of+laryngeal+vibrations%5BTitle%5D)+AND+%22Curr+Opin+Otolaryngol+Head+Neck+Surg%22%5BJournal%5D)">Kymographic imaging of laryngeal vibrations.</a> Curr Opin Otolaryngol Head Neck Surg. 20 (6), 458-465 (2012).</li>
<li>Doellinger, M., Berry, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Visualization+and+quantification+of+the+medial+surface+dynamics+of+an+excised+human+vocal+fold+during+phonation%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Visualization and quantification of the medial surface dynamics of an excised human vocal fold during phonation.</a> J Voice. 20 (3), 401-413 (2006).</li>
<li>Kusuyama, T., Fukuda, H., Shiotani, A., Nakagawa, H., Kanzaki, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Analysis+of+vocal+fold+vibration+by+x-ray+stroboscopy+with+multiple+markers%5BTitle%5D)+AND+%22Otolaryngol+Head+Neck+Surg%22%5BJournal%5D)">Analysis of vocal fold vibration by x-ray stroboscopy with multiple markers.</a> Otolaryngol Head Neck Surg. 124 (3), 317-322 (2001).</li>
<li>Fabre, P. Un procédé électrique percuntané d'inscription de l'accolement glottique au cours de la phonation: glottographie de haute fréquence; premiers résultats [A non-invasive electric method for measuring glottal closure during phonation: High frequency glottography: first results]. Bull. Acad. Nat. Med. 141, 66-69 (1957).</li>
<li>Baken, R. J. <a target="_blank" href="http://www.jvoice.org/article/S0892-1997(05)80123-7/abstract">Electroglottography.</a> J Voice. 6 (2), 98-110 (1992).</li>
<li>Baer, T. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aBaer%2C+T+%22Vocal+Fold+Physiology%22">Vocal Fold Physiology</a>. Stevens, K. N., Hirano, M. , University of Tokyo Press. Tokyo. 119-133 (1981).</li>
<li>Pelorson, X., Hirschberg, A., van Hassel, R. R., Wijnands, A. P. J., Auregan, Y. <a target="_blank" href="http://asa.scitation.org/doi/abs/10.1121/1.411449">Theoretical and experimental study of quasisteady-flow separation within the glottis during phonation. Application to a modified two-mass model.</a> J Acoust Soc Am. 96 (6), 3416-3431 (1994).</li>
<li>Alipour, F., Scherer, R. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Flow+separation+in+a+computational+oscillating+vocal+fold+model%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Flow separation in a computational oscillating vocal fold model.</a> J Acoust Soc Am. 116 (3), 1710-1719 (2004).</li>
<li>Zhang, Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Influence+of+flow+separation+location+on+phonation+onset%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Influence of flow separation location on phonation onset.</a> J Acoust Soc Am. 124 (3), 1689-1694 (2008).</li>
<li>Kaburagi, T., Tanabe, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Low-dimensional+models+of+the+glottal+flow+incorporating+viscous-inviscid+interaction%5BTitle%5D)+AND+%22J+Acoust+Soc+Am%22%5BJournal%5D)">Low-dimensional models of the glottal flow incorporating viscous-inviscid interaction.</a> J Acoust Soc Am. 125 (1), 391-404 (2009).</li>
<li>Sidlof, P., Doaré, O., Cadot, O., Chaigne, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Measurement+of+flow+separation+in+a+human+vocal+folds+model%5BTitle%5D)+AND+%22Exp+Fluids%22%5BJournal%5D)">Measurement of flow separation in a human vocal folds model.</a> Exp Fluids. 51 (1), 123-136 (2011).</li>
<li>Smith, S. L., Thomson, S. L. <a target="_blank" href="https://www.ncbi.nlm.nih.gov/pmc/articles/PMC3356320/">Effect of inferior surface angle on the self-oscillation of a computational vocal fold model.</a> J Acoust Soc Am. 131 (5), 4062-4075 (2012).</li>
<li>Khosla, S., Oren, L., Ying, J., Gutmark, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Direct+simultaneous+measurement+of+intraglottal+geometry+and+velocity+fields+in+excised+larynges%5BTitle%5D)+AND+%22Laryngoscope%22%5BJournal%5D)">Direct simultaneous measurement of intraglottal geometry and velocity fields in excised larynges.</a> Laryngoscope. 124, S1-S13 (2014).</li>
<li>Brücker, C., Kirmse, C., Triep, M. <a target="_blank" href="http://www.ingentaconnect.com/contentone/dav/aaua/2016/00000102/00000002/art00007">Feedback of the glottal jet flow with supraglottal wall oscillations.</a> Acta Acustica United With Acustica. 102 (2), 240-243 (2016).</li>
<li>Herbst, C. T., Fitch, W. T., Lohscheller, J., Svec, J. G. <a target="_blank" href="NULL">AQL 2013, Proceedings of the 10th International Conference on Advances in Quantitative Laryngology, Voice and Speech Research</a>. Deliyski, D. D. , AQL Press. Cincinnati, Ohio, USA. 75-76 (2013).</li>
<li>Berke, G. S., Gerratt, B. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Laryngeal+biomechanics%3A+an+overview+of+mucosal+wave+mechanics%5BTitle%5D)+AND+%22J+Voice%22%5BJournal%5D)">Laryngeal biomechanics: an overview of mucosal wave mechanics.</a> J Voice. 7 (2), 123-128 (1993).</li>
<li>Boessenecker, A., Berry, D. A., Lohscheller, J., Eysholdt, U., Doellinger, M. <a target="_blank" href="http://www.ingentaconnect.com/contentone/dav/aaua/2007/00000093/00000005/art00015">Mucosal wave properties of a human vocal fold.</a> Acta Acustica United With Acustica. 93 (5), 815-823 (2007).</li>
<li>Hirano, M. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aHirano%2C+M+%22Clinical+examination+of+voice%22">Clinical examination of voice</a>. 5, Springer-Verlag. Wien, Austria. (1981).</li>
<li>Jing, B., Tang, S., Wu, L., Wang, S., Wan, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Visualizing+the+Vibration+of+Laryngeal+Tissue+during+Phonation+Using+Ultrafast+Plane+Wave+Ultrasonography%5BTitle%5D)+AND+%22Ultrasound+in+Med+BIol%22%5BJournal%5D)">Visualizing the Vibration of Laryngeal Tissue during Phonation Using Ultrafast Plane Wave Ultrasonography.</a> Ultrasound in Med BIol. 42 (12), 2812-2825 (2016).</li>
<li>Herbst, C. T. Ch. 6. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aHerbst%2C+CT+%22Vertebrate+Sound+Production+and+Acoustic+Communication%22">Vertebrate Sound Production and Acoustic Communication</a>. Suthers, R. A., Fitch, W. T., Fay, R. R., Popper, A. N. , Springer International Publishing. Switzerland. 159-189 (2016).</li>
</ol>

The authors have nothing to disclose.

The hemi-larynx preparation shares the advantages of the &#34;conventional&#34; (full) excised larynx setup: In such an experimental approach, physical and physiological boundary conditions and parameters (such as subglottal pressure or vocal fold elongation) can be controlled fairly well. The behavior of the hemilarynx is homologous to that of a full larynx with a perfect lateral symmetry, with the exception that magnitudes of some parameters (e.g., air flow rate, sound pressure) are reduced by approximately 50...

Voice is typically created by vibrating laryngeal tissue (mainly the vocal folds), which converts a steady airflow, supplied by the lungs, into a sequence of airflow pulses. The acoustic pressure waveform (i.e., the primary sound) emerging from this sequence of flow pulses acoustically excites the vocal tract which filters them, and the resulting sound is radiated from the mouth and (to a certain degree) from the nose1. The spectral composition of the generated sound is largely influenced by the quality of vocal fold vibration, governed by laryngeal biomechanics and interactions with the tracheal airflow2. Both in a clinical and a research context, documentation and assessment of vocal fold vibration is thus of foremost interest when studying voice production.
In humans, direct endoscopic investigation of the larynx during sound production in vivo is challenging, and it is virtually impossible in nonhuman mammals, given current technological means. Therefore, and in order to guarantee carefully controlled physical and/or physiological experimental boundary conditions, the use of excised larynges3,4 is in many cases an adequate substitution for investigation of in vivo voice production mechanisms.
Vocal fold vibration is a complex three-dimensional phenomenon5. While conventional investigation methods like laryngeal endoscopy (in vivo) or excised larynx preparations typically provide only a superior view of the vibrating vocal folds6, they do not allow for complete three-dimensional analysis of vocal fold motion. In particular, in the superior view the lower (caudal) margins of the vocal folds are invisible during a major portion of the vibratory cycle. This is due to the phase delay between the inferior (caudal) and the superior (cranial) edge of the vocal folds, a phenomenon which is typically seen during vocal fold oscillation5. As direct empirical evidence for backing up findings from mathematical and physical models is scarce, knowledge of the geometry and motion of the lower vocal fold edge7, and thus the geometry of the subglottal channel8,9,10 is crucial for better understanding the interaction between laryngeal airflow, vocal fold tissue, and the resulting forces and pressures11,12. Another aspect of vocal fold vibration that is hidden from the customary superior view is the vertical (caudo-cranial) depth of the contact between the two vocal folds. The vertical contact depth is related to the vertical thickness of the vocal folds, which is a potential indicator of the vocal register used in singing (&#34;chest&#34; vs. &#34;falsetto&#34; register)13,14.
In order to overcome the shortcomings of conventional (full) excised larynx preparations, a so-called hemi-larynx setup can be utilized, where one half of the larynx is removed, thus facilitating the assessment of the vibratory characteristics of the remaining vocal fold in three dimensions. Surprisingly, since the introduction of this setup in the 1960s15 and an initial validation of the concept in 199316, not many laboratories have performed experiments with this promising experimental approach17,18,19,20,21,22,23. An explanation for this might be found in the difficulties of creating a viable hemi-larynx preparation. While the conventional excised (full) larynx preparation is well documented4, no such in-depth instructions are as yet available for creating a hemi-larynx setup. It is therefore the purpose of this paper to provide a tutorial for establishing a reliably reproducible hemi-larynx setup, supplemented by experimental results from red deer specimens.
A hemi-larynx setup shares many features with a &#34;conventional&#34; excised larynx setup, such as measurement equipment, high-speed or other imaging technology to adequately document the vibrations of the laryngeal structures during sound generation, or proper supply of heated, humidified air. These general setup considerations are described in detail in both a book chapter4 and a technical report from the National Center of Voice and Speech24. Reiteration of these instructions would be beyond the scope of this manuscript. Here, only the specialized directives for generating a hemi-larynx setup are presented.

<table><tbody><tr><td>Surgical blades</td><td>Surgeon</td><td>Jai Surgical Ltd., New Delhi, India</td><td></td></tr><tr><td>Saw</td><td>Hand saw (Lux, 150 mm length)</td><td>Lux, Wermelskirchen, Germany</td><td></td></tr><tr><td>Thermometer</td><td>Testo 922</td><td>Testo Ltd., Hampshire, UK</td><td>K-type Probe, Operating temperature -20 to +50 &amp;deg;C</td></tr><tr><td>Autoclave bags</td><td>Autoclave bags</td><td>vwr.com, VWR International s.r.o., Stribrna Skalice, Czech republic</td><td></td></tr><tr><td>Conductive glass plates</td><td>Custom made</td><td>UPOL - Joint laboratory of Optics&lt;br/&gt; Trida 17. listopadu 50A, 772 07 Olomouc, the Czech Rep.</td><td></td></tr><tr><td>Fixative cream</td><td>Denture fixative cream</td><td>Blend-a-dent Natural</td><td></td></tr><tr><td>Prongs and fastening system</td><td>Customized Kanya Al eloxed profiles</td><td>Distributor: VISIMPEX a.s.. Seifertova 33, 750 02 Prerov, the Czech Rep.;</td><td>&amp;nbsp;Combination of Kanya RVS and PVS fastening systems (http://www.kanya.cz/) + custom made prongs</td></tr><tr><td>Mounting tube</td><td>Custom made</td><td>UPOL - Joint laboratory of Optics,&lt;br/&gt; Trida 17. listopadu 50A, 772 07 Olomouc, the Czech Rep.</td><td></td></tr><tr><td>LED Light</td><td>Verbatim 52204 LED Lamp</td><td>Mitsubishi Chemical Holdings Corporation, Tokyo, Japan</td><td></td></tr><tr><td>Camera</td><td>Canon EOS1100D</td><td>Canon Inc.</td><td>18-55 mm lens</td></tr><tr><td>Airpump</td><td>Resun LP100</td><td>Resun</td><td></td></tr><tr><td>Strobe light</td><td>ELMED Helio-Strob micro2</td><td>ELMED Dr. Ing. Mense GmbH, Heiligenhaus, Germany</td><td></td></tr><tr><td>Humidifier</td><td>Custom made</td><td>Voice Research Lab, Dept. Biophysics, Faculty of Sciences, Palacky University Olomouc, Czech republic</td><td></td></tr><tr><td>Subglottic tract</td><td>Custom made adjustable subglottic tract</td><td>Voice Research Lab, Dept. Biophysics, Faculty of Sciences, Palacky University Olomouc, Czech republic</td><td>Hampala, V., Svec, Jan, Schovanek, P., and Mandat, D. Uzitny vzor c. 25585: Model subglotickeho traktu. [Utility model no. 25585: Model of subglottal tract] (In Czech) Soukup, P. 2013-27834(CZ 25505 U1), 1-7. 24-6-2013. Praha, Urad prumysloveho vlastnictvi</td></tr></tbody></table>

hemi-laryngeal setup for studying vocal fold vibration in three dimensions

The voice of humans and most non-human mammals is generated in the larynx through self-sustaining oscillation of the vocal folds. Direct visual documentation of vocal fold vibration is challenging, particularly in non-human mammals. As an alternative, excised larynx experiments provide the opportunity to investigate vocal fold vibration under controlled physiological and physical conditions. However, the use of a full larynx merely provides a top view of the vocal folds, excluding crucial portions of the oscillating structures from observation during their interaction with aerodynamic forces. This limitation can be overcome by utilizing a hemi-larynx setup where one half of the larynx is mid-sagittally removed, providing both a superior and a lateral view of the remaining vocal fold during self-sustained oscillation.
Here, a step-by-step guide for the anatomical preparation of hemi-laryngeal structures and their mounting on the laboratory bench is given. Exemplary phonation of the hemi-larynx preparation is documented with high-speed video data captured by two synchronized cameras (superior and lateral views), showing three-dimensional vocal fold motion and corresponding time-varying contact area. The documentation of the hemi-larynx setup in this publication will facilitate application and reliable repeatability in experimental research, providing voice scientists with the potential to better understand the biomechanics of voice production.

Illustrations of the hemi-larynx preparation and its mounting on the air supply tube, as referenced in the previous section, are provided in Figure 1 and Figure 2, respectively.
Documentation of vocal fold vibration from two camera angles
Airflow-induced self-sustaining oscillation of the hemi...

Watch this Scientific Journal Video about Hemi-laryngeal Setup for Studying Vocal Fold Vibration in Three Dimensions at JoVE.com

Hemi-laryngeal Setup for Studying Vocal Fold Vibration in Three Dimensions

This paper introduces a protocol for the preparation of hemi-larynx specimens facilitating a multi-dimensional view of vocal fold vibration, in order to investigate various biophysical aspects of voice production in humans and non-human mammals.

The voice of humans and most non-human mammals is generated in the larynx through self-sustaining oscillation of the vocal folds. Direct visual ...

hemi-laryngeal-setup-for-studying-vocal-fold-vibration-three

Research

JoVE Journal

Biology

10.9K Views.  Palacky University Olomouc. This paper introduces a protocol for the preparation of hemi-larynx specimens facilitating a multi-dimensional view of vocal fold vibration, in order to investigate various biophysical aspects of voice production in humans and non-human mammals.

Video: Hemi-laryngeal Setup for Studying Vocal Fold Vibration in Three Dimensions

Synthetic, Multi-Layer, Self-Oscillating Vocal Fold Model Fabrication

Sound for the human voice is produced via flow-induced vocal fold vibration. The vocal folds consist of several layers of tissue, each with differing material properties 1. Normal voice production relies on healthy tissue and vocal folds, and occurs as a result of complex coupling between aerodynamic, structural dynamic, and acoustic physical phenomena. Voice disorders affect up to 7.5 million annually in the United States alone 2 and often result in significant financial, social, and other quality-of-life difficulties. Understanding the physics of voice production has the potential to significantly benefit voice care, including clinical prevention, diagnosis, and treatment of voice disorders.
Existing methods for studying voice production include in vivo experimentation using human and animal subjects, in vitro experimentation using excised larynges and synthetic models, and computational modeling. Owing to hazardous and difficult instrument access, in vivo experiments are severely limited in scope. Excised larynx experiments have the benefit of anatomical and some physiological realism, but parametric studies involving geometric and material property variables are limited. Further, they are typically only able to be vibrated for relatively short periods of time (typically on the order of minutes).
Overcoming some of the limitations of excised larynx experiments, synthetic vocal fold models are emerging as a complementary tool for studying voice production. Synthetic models can be fabricated with systematic changes to geometry and material properties, allowing for the study of healthy and unhealthy human phonatory aerodynamics, structural dynamics, and acoustics. For example, they have been used to study left-right vocal fold asymmetry 3,4, clinical instrument development 5, laryngeal aerodynamics 6-9, vocal fold contact pressure 10, and subglottal acoustics 11 (a more comprehensive list can be found in Kniesburges et al. 12)
Existing synthetic vocal fold models, however, have either been homogenous (one-layer models) or have been fabricated using two materials of differing stiffness (two-layer models). This approach does not allow for representation of the actual multi-layer structure of the human vocal folds 1 that plays a central role in governing vocal fold flow-induced vibratory response. Consequently, one- and two-layer synthetic vocal fold models have exhibited disadvantages 3,6,8 such as higher onset pressures than what are typical for human phonation (onset pressure is the minimum lung pressure required to initiate vibration), unnaturally large inferior-superior motion, and lack of a "mucosal wave" (a vertically-traveling wave that is characteristic of healthy human vocal fold vibration).
In this paper, fabrication of a model with multiple layers of differing material properties is described. The model layers simulate the multi-layer structure of the human vocal folds, including epithelium, superficial lamina propria (SLP), intermediate and deep lamina propria (i.e., ligament; a fiber is included for anterior-posterior stiffness), and muscle (i.e., body) layers 1. Results are included that show that the model exhibits improved vibratory characteristics over prior one- and two-layer synthetic models, including onset pressure closer to human onset pressure, reduced inferior-superior motion, and evidence of a mucosal wave.

The methodology for fabricating synthetic vocal fold models is described. The models are life-sized and mimic the multi-layer structure of the human vocal folds. Results show the models to self-oscillate at pressures comparable to lung pressure and demonstrate flow-induced vibratory responses that are similar to those of human vocal folds.

Sound for the human voice is produced via flow-induced vocal fold vibration. The vocal folds consist of several layers of tissue, each with differing ...

Bioengineering

Chip-based Three-dimensional Cell Culture in Perfused Micro-bioreactors

We have developed a chip-based cell culture system for the three-dimensional cultivation of cells. The chip is typically manufactured from non-biodegradable polymers, e.g., polycarbonate or polymethyl methacrylate by micro injection molding, micro hot embossing or micro thermoforming. But, it can also be manufactured from bio-degradable polymers. Its overall dimensions are 0.7 1 x 20 x 20 x 0.7 1 mm (h x w x l). The main features of the chips used are either a grid of up to 1156 cubic micro-containers (cf-chip) each the size of 120-300 x 300 x 300 &mu; (h x w x l) or round recesses with diameters of 300 &mu; and a depth of 300 &mu; (r-chip). The scaffold can house 10 Mio. cells in a three-dimensional configuration. For an optimal nutrient and gas supply, the chip is inserted in a bioreactor housing. The bioreactor is part of a closed steril circulation loop that, in the simplest configuration, is additionaly comprised of a roller pump and a medium reservoir with a gas supply. The bioreactor can be run in perfusion, superfusion, or even a mixed operation mode. We have successfully cultivated cell lines as well as primary cells over periods of several weeks. For rat primary liver cells we could show a preservation of organotypic functions for more than 2 weeks. For hepatocellular carcinoma cell lines we could show the induction of liver specific genes not or only slightly expressed in standard monolayer culture. The system might also be useful as a stem cell cultivation system since first differentiation experiments with stem cell lines were promising.

We describe a chip-based platform for the three-dimensional cultivation of cells in micro-bioreactors. One chip can house up to 10 Mio. cells that can be cultivated under precisely defined conditions with regard to fluid flow, oxygen tension etc. in a sterile, closed circulation loop.

We have developed a chip-based cell culture system for the three-dimensional cultivation of cells. The chip is typically manufactured from ...

Investigating the Three-dimensional Flow Separation Induced by a Model Vocal Fold Polyp

The fluid-structure energy exchange process for normal speech has been studied extensively, but it is not well understood for pathological conditions. Polyps and nodules, which are geometric abnormalities that form on the medial surface of the vocal folds, can disrupt vocal fold dynamics and thus can have devastating consequences on a patient&#39;s ability to communicate. Our laboratory has reported particle image velocimetry (PIV) measurements, within an investigation of a model polyp located on the medial surface of an in&#160;vitro driven vocal fold model, which show that such a geometric abnormality considerably disrupts the glottal jet behavior. This flow field adjustment is a likely reason for the severe degradation of the vocal quality in patients with polyps. A more complete understanding of the formation and propagation of vortical structures from a geometric protuberance, such as a vocal fold polyp, and the resulting influence on the aerodynamic loadings that drive the vocal fold dynamics, is necessary for advancing the treatment of this pathological condition. The present investigation concerns the three-dimensional flow separation induced by a wall-mounted prolate hemispheroid with a 2:1 aspect ratio in cross flow, i.e. a model vocal fold polyp, using an oil-film visualization technique. Unsteady, three-dimensional flow separation and its impact of the wall pressure loading are examined using skin friction line visualization and wall pressure measurements.

Vocal fold polyps can disrupt vocal fold dynamics and thus can have devastating consequences on a patient&#39;s ability to communicate. Three-dimensional flow separation induced by a wall-mounted model polyp and its impact on the wall pressure loading are examined using particle image velocimetry, skin friction line visualization, and wall pressure measurements.

The fluid-structure energy exchange process for normal speech has been studied extensively, but it is not well understood for pathological conditions. ...

Construction and Characterization of a Novel Vocal Fold Bioreactor

In vitro engineering of mechanically active tissues requires the presentation of physiologically relevant mechanical conditions to cultured cells. To emulate the dynamic environment of vocal folds, a novel vocal fold bioreactor capable of producing vibratory stimulations at fundamental phonation frequencies is constructed and characterized. The device is composed of a function generator, a power amplifier, a speaker selector and parallel vibration chambers. Individual vibration chambers are created by sandwiching a custom-made silicone membrane between a pair of acrylic blocks. The silicone membrane not only serves as the bottom of the chamber but also provides a mechanism for securing the cell-laden scaffold. Vibration signals, generated by a speaker mounted underneath the bottom acrylic block, are transmitted to the membrane aerodynamically by the oscillating air. Eight identical vibration modules, fixed on two stationary metal bars, are housed in an anti-humidity chamber for long-term operation in a cell culture incubator. The vibration characteristics of the vocal fold bioreactor are analyzed non-destructively using a Laser Doppler Vibrometer (LDV). The utility of the dynamic culture device is demonstrated by culturing cellular constructs in the presence of 200-Hz sinusoidal vibrations with a mid-membrane displacement of 40 &#181;m. Mesenchymal stem cells cultured in the bioreactor respond to the vibratory signals by altering the synthesis and degradation of vocal fold-relevant, extracellular matrix components. The novel bioreactor system presented herein offers an excellent in vitro platform for studying vibration-induced mechanotransduction and for the engineering of functional vocal fold tissues.

A novel vocal fold bioreactor capable of delivering physiologically relevant, vibratory stimulation to cultured cells is constructed and characterized. This dynamic culture device, when combined with a fibrous poly(&#949;-caprolactone) scaffold, creates a vocal fold-mimetic environment that modulates the behaviors of mesenchymal stem cells.

In vitro engineering of mechanically active tissues requires the presentation of physiologically relevant mechanical conditions to cultured cells. To ...

Microinjection Techniques for Studying Mitosis in the Drosophila melanogaster Syncytial Embryo

This protocol describes the use of the Drosophila melanogaster syncytial embryo for studying mitosis1. Drosophila has useful genetics with a sequenced genome, and it can be easily maintained and manipulated. Many mitotic mutants exist, and transgenic flies expressing functional fluorescently (e.g. GFP) - tagged mitotic proteins have been and are being generated. Targeted gene expression is possible using the GAL4/UAS system2. 

The Drosophila early embryo carries out multiple mitoses very rapidly (cell cycle duration, &asymp;10 min). It is well suited for imaging mitosis, because during cycles 10-13, nuclei divide rapidly and synchronously without intervening cytokinesis at the surface of the embryo in a single monolayer just underneath the cortex. These rapidly dividing nuclei probably use the same mitotic machinery as other cells, but they are optimized for speed; the checkpoint is generally believed to not be stringent, allowing the study of mitotic proteins whose absence would cause cell cycle arrest in cells with a strong checkpoint. Embryos expressing GFP labeled proteins or microinjected with fluorescently labeled proteins can be easily imaged to follow live dynamics (Fig. 1). In addition, embryos can be microinjected with function-blocking antibodies or inhibitors of specific proteins to study the effect of the loss or perturbation of their function3. These reagents can diffuse throughout the embryo, reaching many spindles to produce a gradient of concentration of inhibitor, which in turn results in a gradient of defects comparable to an allelic series of mutants. Ideally, if the target protein is fluorescently labeled, the gradient of inhibition can be directly visualized4. It is assumed that the strongest phenotype is comparable to the null phenotype, although it is hard to formally exclude the possibility that the antibodies may have dominant effects in rare instances, so rigorous controls and cautious interpretation must be applied. Further away from the injection site, protein function is only partially lost allowing other functions of the target protein to become evident.

Microinjection Techniques for Studying Mitosis in the Drosophila melanogaster Syncytial Embryo

This protocol describes the use of microinjection and high resolution imaging in the Drosophila melanogaster syncytial embryo to study mitosis.

This protocol describes the use of the Drosophila melanogaster syncytial embryo  for studying mitosis1.  Drosophila has useful genetics with a sequenced ...

3D Printing of Multilayered Silicone Vocal Fold Models

Manufacturing Process for Non-Adhesive Super-Soft Vocal Fold Models

This study aims to develop super-soft, non-sticky vocal fold models for voice research. The conventional manufacturing process of silicone-based vocal fold models results in models with undesirable properties, such as stickiness and reproducibility issues. Those vocal fold models are prone to rapid aging, leading to poor comparability across different measurements. In this study, we propose a modification to the manufacturing process by changing the order of layering the silicone material, which leads to the production of non-sticky and highly consistent vocal fold models. We also compare a model produced using this method with a conventionally manufactured vocal fold model that is adversely affected by its sticky surface. We detail the manufacturing process and characterize the properties of the models for potential applications. The outcomes of the study demonstrate the efficacy of the modified fabrication method, highlighting the superior qualities of our non-sticky vocal fold models.&#160;The findings contribute to the development of realistic and reliable vocal fold models for research and clinical applications.

Author Spotlight: Advancements in the Fabrication of Synthetic Vocal Fold Models for Phonetic and Robotic Applications

This study demonstrates the manufacturing of non-sticky and super-soft vocal fold models by introducing a specific way to create the vocal fold layers, providing a detailed description of the manufacturing procedure, and characterizing the properties of the models.

This study aims to develop super-soft, non-sticky vocal fold models for voice research. The conventional manufacturing process of silicone-based vocal ...

Engineering

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may also be used to study the structure-function relationship for other ion channels and neurotransmitter receptors1. BK channels are widely expressed in different tissues and have been implicated in many physiological functions, including regulation of smooth muscle contraction, frequency tuning of inner hair cells and regulation of neurotransmitter release2-6. BK channels are activated by membrane depolarization and by intracellular Ca2+ and Mg2+ 6-9. Therefore, the protocol is designed to control both the membrane voltage and the intracellular solution. In this protocol, messenger RNA of BK channels is injected into Xenopus laevis oocytes (stage V-VI) followed by 2-5 days of incubation at 18&deg;C10-13. Membrane patches that contain single or multiple BK channels are excised with the inside-out configuration using patch clamp techniques10-13. The intracellular side of the patch is perfused with desired solutions during recording so that the channel activation under different conditions can be examined. To summarize, the mRNA of BK channels is injected into Xenopus laevis oocytes to express channel proteins on the oocyte membrane; patch clamp techniques are used to record currents flowing through the channels under controlled voltage and intracellular solutions.

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Ionic current of BK channels is recorded using patch clamp techniques. BK channels are expressed in Xenopus oocytes by injecting messenger RNA. The intracellular solution during patch clamp recordings is controlled by a perfusion system.

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may ...

Preparation of the Rat Vocal Fold for Neuromuscular Analyses

The purpose of this tutorial is to describe the preparation of the rat vocal fold for histochemical neuromuscular study. This protocol outlines procedures for rat laryngeal dissection, flash-freezing, and cryosectioning of the vocal folds. This study describes how to cryosection vocal folds in both longitudinal and cross-sectional planes. A novelty of this protocol is the laryngeal tracking during cryosectioning that ensures accurate identification of the intrinsic laryngeal muscles and reduces the chance of tissue loss. Figures demonstrate the progressive cryosectioning in both planes. Twenty-nine rat hemi-larynges were cryosectioned and tracked from the emergence of the thyroid cartilage to the appearance of the first section that included the full vocal fold. The full vocal fold was visualized for all animals in both planes. There was high variability in the distance from the appearance of the thyroid cartilage to the appearance of the full vocal fold in both planes. Weight was not correlated to depth of laryngeal landmarks, suggesting individual variability and other factors related to tissue preparation may be responsible for the high variability in the appearance of landmarks during sectioning. This study details a methodology and presents morphological data for preparing the rat vocal fold for histochemical neuromuscular investigation. Due to high individual variability, laryngeal landmarks should be closely tracked during cryosectioning to prevent oversectioning tissue and tissue loss. The use of a consistent methodology, including adequate tissue preparation and awareness of landmarks within the rat larynx, will assist with consistent results across studies and aid new researchers interested in using the rat vocal fold as a model to investigate laryngeal neuromuscular mechanisms.

This protocol describes methods used to prepare rat vocal folds for histochemical neuromuscular study.

The purpose of this tutorial is to describe the preparation of the rat vocal fold for histochemical neuromuscular study. This protocol outlines procedures ...

Neuroscience

Learning Modern Laryngeal Surgery in a Dissection Laboratory

Surgery for laryngeal malignancies requires millimetric accuracy from the different endoscopic and open techniques available. Practice of this surgery is almost completely reserved to a few referral centers that deal with a large proportion of this pathology. Practice on human specimens is not always possible for ethical, economic, or availability reasons. The aim of this study is to provide a reproducible method for the organization of a laryngeal laboratory on ex vivo animal models where it is possible to approach, learn, and refine laryngeal techniques. Porcine and ovine larynges are ideal, affordable, models to simulate laryngeal surgery given their similarity to the human larynx in their anatomical layout and tissue composition. Herein, the surgical steps of transoral laser surgery, open partial horizontal laryngectomy, and total laryngectomy are reported. The merging of endoscopic and exoscopic views guarantees an inside-out perspective, which is vital for the comprehension of the complex laryngeal anatomy. The method was successfully adopted during three sessions of a dissection course &#34;Lary-Gym&#34;. Further perspectives on robotic surgical training are described.

The purpose of this paper is to illustrate how to organize a reproducible laboratory for laryngeal surgery on affordable and closely similar animal laryngeal models in order to improve anatomical and surgical knowledge and skills.

Surgery for laryngeal malignancies requires millimetric accuracy from the different endoscopic and open techniques available. Practice of this surgery is ...

Medicine

FRET Imaging in Three-dimensional Hydrogels

Imaging of F&#246;rster resonance energy transfer (FRET)&#160;is a powerful tool for examining cell biology in real-time. Studies utilizing FRET commonly employ two-dimensional (2D) culture, which does not mimic the three-dimensional (3D) cellular microenvironment. A method to perform quenched emission FRET imaging using conventional widefield epifluorescence microscopy of cells within a 3D hydrogel environment is presented. Here an analysis method for ratiometric FRET probes that yields linear ratios over the probe activation range is described. Measurement of intracellular cyclic adenosine monophosphate (cAMP) levels is demonstrated in chondrocytes under forskolin stimulation using a probe for EPAC1 activation (ICUE1) and the ability to detect differences in cAMP signaling dependent on hydrogel material type, herein a photocrosslinking hydrogel (PC-gel, polyethylene glycol dimethacrylate) and a thermoresponsive hydrogel (TR-gel). Compared with 2D FRET methods, this method requires little additional work. Laboratories already utilizing FRET imaging in 2D can easily adopt this method to perform cellular studies in a 3D microenvironment. It can further be applied to high throughput drug screening in engineered 3D microtissues. Additionally, it is compatible with other forms of FRET imaging, such as anisotropy measurement and fluorescence lifetime imaging (FLIM), and with advanced microscopy platforms using confocal, pulsed, or modulated illumination.

F&#246;rster resonance energy transfer (FRET) imaging is a powerful tool for real-time cell biology studies. Here a method for FRET imaging cells in physiologic three-dimensional (3D) hydrogel microenvironments using conventional epifluorescence microscopy is presented. An analysis for ratiometric FRET probes that yields linear ratios over the activation range is described.

Imaging of F&#246;rster resonance energy transfer (FRET)&#160;is a powerful tool for examining cell biology in real-time. Studies utilizing FRET commonly ...

Hemi-laryngeal Setup for Studying Vocal Fold Vibration in Three Dimensions

Summary

Explore More Videos

Synthetic, Multi-Layer, Self-Oscillating Vocal Fold Model Fabrication

Chip-based Three-dimensional Cell Culture in Perfused Micro-bioreactors

Investigating the Three-dimensional Flow Separation Induced by a Model Vocal Fold Polyp

Construction and Characterization of a Novel Vocal Fold Bioreactor

Microinjection Techniques for Studying Mitosis in the Drosophila melanogaster Syncytial Embryo

Manufacturing Process for Non-Adhesive Super-Soft Vocal Fold Models

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Preparation of the Rat Vocal Fold for Neuromuscular Analyses

Learning Modern Laryngeal Surgery in a Dissection Laboratory

FRET Imaging in Three-dimensional Hydrogels