Name: metabolic support of excised, living brain tissues during magnetic resonance microscopy acquisition
Uploaded: 2017-10-18T13:00:00.000+00:00
Duration: 10 min 21 s
Description: Watch this Scientific Journal Video about Metabolic Support of Excised, Living Brain Tissues During Magnetic Resonance Microscopy Acquisition at JoVE.com

This work was supported by grants from the National Institutes of Health (1R21NS094061-01A1) (NIH 1R01EB012874-01) (S10RR031637), and the National Science Foundation (cooperative agreement No. DMR-1157490) through the National High Magnetic Field Laboratory (NHMFL) Advanced Magnetic Resonance Imaging and Spectroscopy (AMRIS) facility at UF and the State of Florida.

All animal experiments described follow the guidelines set forth in the National Academies of Sciences&#39; Guide for the Care and Use of Laboratory Animals and were reviewed and approved by the University of Florida&#39;s Institutional Animal Care and Use Committee (IACUC). Follow all applicable rules and regulations when engaging in animal subject research.
1. Preparation of Perfusate for the Maintenance of Central Nervous System Tissues
<ol>
	<li>Make fresh artificial cerebrospinal fluid (aCSF).
	<ol>
		<li>To generate 2 L of bicarbonate-buffered aCSF perfusate, measure out 1,500 mL of water purified by double distillation or reverse osmosis into a 4 L flask. Place a magnetic stir bar in the flask and agitate the liquid using a stir plate.</li>
		<li>Into the purified water, dissolve the following quantities of salts: 14.03 g (120 mM) sodium chloride, 4.37 g (26 mM) sodium bicarbonate, 0.41 g (1.5 mM) monobasic potassium phosphate, 0.69 g (1.4 mM) magnesium sulfate heptahydrate, 0.59 g (2 mM) calcium chloride dihydrate, 0.45 g (3 mM) potassium chloride, and 3.6 g (10 mM) glucose. 
		NOTE: The chemical contents of the perfusate will differ depending on the specific metabolic requirements of the tissue and the desired conditions of the experiment.</li>
		<li>Mix this solution thoroughly until all salts have dissolved. Adjust volume to 2 L using additional purified water.</li>
		<li>Test the osmolality of the aCSF using a freezing point depression osmometer. Adjust to 300 mOsm/kg using sorbitol. Addition of 324 mg sorbitol to 2 L of 299 mOsm/kg aCSF perfusate will increase osmolality to 300 mOsm/kg (approximately 1 mOsm per 324mg). 
		NOTE: The aCSF can be stored at 4 &#176;C in an air-tight, sealed bottle for a period not to exceed 24 h.</li>
	</ol>
	</li>
</ol>
2. Set Up the Perfusion System
<ol>
	<li>Prepare the aCSF perfusate.
	<ol>
		<li>Equilibrate aCSF to ambient temperature (~23 &#176;C) while gassing with 95% carbogen (95% O2, 5% CO2; 1/16 L/min) via direct bubbling for no less than 1 h. 
		NOTE: Different tissue types or desired experimental conditions may require adjustment of the perfusate temperature or gas contents. The desired conditions for dissolved gas content in the perfusate can be controlled precisely by varying the percent concentrations of individual components of the supply gas (Figure 1).</li>
		<li>Once the aCSF reaches the required temperature and carbogen saturation, confirm that the pH is in the physiological range (7.3 - 7.4). Continue to bubble gas directly into the perfusate reservoir (1/16 L/min) throughout the course of experiment in order to maintain proper dissolved oxygen content and pH conditions conducive to healthy tissue metabolism.</li>
	</ol>
	</li>
	<li>Prime the perfusion lines.
	<ol>
		<li>Submerge the inlet tube connected to the peristaltic micro-pump into the prepared aCSF (300 mOsm, pH 7.3 - 7.4, continuously gassed).</li>
		<li>Pass the oxygenator device (Figure 2) and perfusion lines through both the magnet bore and gradient coil stack (top to bottom) and set the coils aside until probe assembly. Hang the oxygenator above a beaker to catch any aCSF effluent. 
		NOTE: Depending on the MRI system design, perfusion lines may need to be passed through the magnet bore and gradient coils or probe body base prior to priming the system with aCSF. Confirm that perfusion line placement will not interfere with the assembly of the probe body or insertion of the probe into the bore before beginning the priming procedure.</li>
		<li>Confirm the intended flow rate (2 mL/min) is selected and begin filling the perfusion lines by switching on the pump.</li>
		<li>Invert the empty, in-line bubble trap so that aCSF will displace the air contained inside.</li>
		<li>Connect the oxygenator&#39;s gas port to a second source of carbogen (either a manifold or a secondary carbogen cylinder) and set a flow rate of 1/16L/min.</li>
		<li>Confirm that carbogen is flowing over the oxygenator&#39;s gas-exchange membrane by dipping the exhaust port on top of the oxygenator into water.</li>
		<li>Once aCSF is detected dripping from the perfusion chamber, purge any visible gas bubbles from the inflow lines by manual agitation.</li>
		<li>Confirm the oxygenator is operating correctly by submerging the oxygen electrode in the aCSF flowing from the perfusion chamber. 
		NOTE: The reading on the oxygen meter should approximate the percentage of oxygen contained within the supplied gas.</li>
	</ol>
	</li>
</ol>
3. Tissue Preparation
<ol>
	<li>Euthanasia
	<ol>
		<li>Place a rat (125 - 150 g) into the induction chamber of an anesthesia machine and expose to 4% isoflurane in an oxygen carrier gas at a rate of 1 L/min for 4 min.</li>
		<li>Remove the unconscious rat from the anesthesia chamber.</li>
		<li>Perform a righting reflex test by placing the rat in the supine position. Check for any movements&#8212;head turning, leg lifting, spine flexing, etc.&#8212;indicative that the animal is turning onto its stomach.</li>
		<li>Perform an eye-blink reflexive test by touching the open eye of the animal using a cotton swab. Check for any response&#8212;lid closure, muscle twitching, etc.&#8212;to this sensory input.</li>
		<li>Lastly, perform a limb-withdraw reflex test by pinching the skin between the toes of the rat&#39;s outstretched back leg using tweezers or hemostats. Check for flexion of the leg. 
		NOTE: In the case of a positive reflexive test result, do not proceed with euthanasia.</li>
		<li>In the event that any of the three reflex tests elicits a response, return the rat immediately to the anesthesia chamber and allow for an additional 2 min of exposure to 4% isoflurane.</li>
		<li>Perform all three reflexive tests over in their entirety. Repeat the 2 min anesthesia exposure as necessary and only proceed once a complete lack of response to all three reflexive tests has been observed.</li>
		<li>Euthanize the rat via guillotine decapitation.</li>
	</ol>
	</li>
	<li>Brain resection
	<ol>
		<li>Remove rat brain by gross dissection. Start with the head in the prone position. Using scissors, cut rostrally through the skin from the back of the neck to the nose and expose the skull.</li>
		<li>Remove soft tissues from the surface of the skull with a blunt probe.</li>
		<li>Working from the caudal end, remove the occipital, parietal, and frontal bones of the cranium using rongeurs.</li>
		<li>Retract the dura by cutting along the longitudinal fissure with micro scissors and peeling back the layer from both hemispheres.</li>
		<li>Remove the brain from the skull by turning the head to the supine position and severing the cranial nerves on the ventral side.</li>
	</ol>
	</li>
	<li>Slice isolation
	<ol>
		<li>Return the brain to the prone position and isolate the central portion containing the hippocampus by removing all tissues caudal to the transverse fissure and rostral to the fimbria. Make two cuts along the transverse plane (i.e. coronal slices) with a straight-edged razor.</li>
		<li>Affix the brain&#39;s caudal-most plane to the center of a vibratome cutting bath using cyanoacrylate glue.</li>
		<li>Add ice-cold, carbogen bubbled aCSF to the vibratome cutting bath and place the nylon retention hardware inside.</li>
		<li>Cut 300 &#956;m thick slices to obtain 3 to 4 usable slice preparations per hemisphere (6 to 8 total).</li>
		<li>Isolate a hippocampus or cortical section from one hemisphere and trim the slice so that it fits within the microcoil&#39;s 5 mm diameter tissue well.</li>
	</ol>
	</li>
</ol>
4. Sample Positioning and Perfusion System Assembly
<ol>
	<li>Coil preparation
	<ol>
		<li>Fill the microcoil&#39;s tissue chamber with oxygenated aCSF from the vibratome&#39;s cutting bath using a transfer pipette.</li>
		<li>Take the trimmed brain sample and position the region of interest (eg. pyramidal cell layer) over the microcoil using a dissecting scope.</li>
		<li>Insert the tissue retention device (nylon mesh net affixed to nylon washer) to retain sample position throughout the imaging experiment. 
		NOTE: Proceed quickly through the sample positioning procedure to minimize exposure to intense light. Provide additional oxygenated aCSF as needed using a transfer pipette.</li>
	</ol>
	</li>
	<li>Assembling the in-bore oxygenator, microcoil and probe
	<ol>
		<li>Secure the modified microcoil assembly (Figure 3) in a table clamp and affix the in-bore oxygenator device by inserting the acetal support peg into the hole on top of the coil.</li>
		<li>Seal the perfusion system by placing the perfusion chamber over the microcoil&#39;s tissue well and cinching the two together using a miniature cable tie.</li>
		<li>Trim the excess length from the cable tie using wire cutters. 
		NOTE: Upon successful sealing, perfusate should be observed exiting through the outflow lines and no leakage should be evident around the silicone seal of the perfusion chamber. Failure to confirm these conditions prior to probe assembly could result in serious damage to imaging hardware.</li>
		<li>Once aCSF can be seen dripping into the waste reservoir, take the microcoil and oxygenator and attach the assembly to the top of the imaging probe body.</li>
		<li>Slide the gradient stack over the assembly and seat the gradient on top of the probe. Photographs detailing the relative placement and proper connection of coil, oxygenator and probe hardware components are provided (Figure 4).</li>
	</ol>
	</li>
</ol>
5. Performing the MR Image Collection
<ol>
	<li>Inserting the assembled probe into the magnet bore
	<ol>
		<li>Place the probe body in close proximity to the spectrometer bore opening at the bottom of the magnet.</li>
		<li>Retract the excess length of perfusion lines through the bore opening at the top of the magnet.</li>
		<li>Once all of the available slack has been taken up from the perfusion lines, advance the probe body into the magnet bore at the base while simultaneously removing more slack from the perfusion lines from the top of the bore.</li>
		<li>Thread the two securing screws at the base of the probe into the corresponding slots of the shim stack.</li>
		<li>Before proceeding, check that perfusion lines were not pinched or kinked during probe insertion by confirming aCSF outflow into the waste reservoir. 
		NOTE: Failure to confirm perfusate outflow can result in permanent damage to perfusion lines and risks catastrophic damage to MR imaging hardware.</li>
		<li>In the event no perfusate is seen exiting the return line into the waste reservoir, remove the probe body and confirm that perfusate flow has recommenced prior to attempting reinsertion. A schematic layout of the assembled perfusion system and imaging spectrometer has been described previously8.</li>
	</ol>
	</li>
	<li>Connecting the Probe Body
	<ol>
		<li>Attach the inflow and outflow water lines from the gradient chiller.</li>
		<li>Turn on the pump for gradient chiller and confirm the water temperature setting (19 &#176;C).</li>
		<li>Attach the air hose from the air chiller unit to the probe body using a hose clamp.</li>
		<li>Turn the flow knob on the air chiller unit to the &#34;1&#34; position.</li>
		<li>Attach the thermocouple wire to the probe body.</li>
		<li>Attach the coaxial cable from the preamp to the radio frequency (RF) input/output on the probe body&#39;s proton (H) channel.</li>
		<li>Attach the power cable from the gradient amplifiers to the probe body.</li>
		<li>Inside the RF cabinet, turn on the power to the B0 compensation unit, all three gradient amplifiers (x,y,z), and the master unit.</li>
	</ol>
	</li>
	<li>Preparing the Spectrometer
	<ol>
		<li>Set the intended bore temperature using the variable temperature adjustment module at the console.</li>
		<li>Match (impedance) and tune (frequency) the RF circuit by adjusting the variable capacitors within the probe. This is accomplished by manipulating the wands at the base of the probe body.</li>
		<li>Adjust the current settings for the spectrometer&#39;s shim coils to maximize the magnetic field homogeneity at the sample.</li>
	</ol>
	</li>
	<li>Begin Image Collection
	<ol>
		<li>Collect pilot images to determine the spatial position of your sample within the magnet bore. Typical parameters for a two dimensional gradient echo are as follows (TR/TE = 100/4 ms, averages = 1, pulse angle = 30o, time = 6 sec, matrix = 64 x 64, field of view = 0.3 x 0.3 cm, resolution = 47 x 47 &#956;m).</li>
		<li>Collect diffusion-weighted pilots in order to confirm proper scan geometry and tissue position if applicable. Typical parameters for a two dimensional diffusion-weighted pilot scan are as follows (TR/TE = 2000/11.6 ms, time = 4.3 min, &#916; = 6 ms, &#948; = 1 ms, averages = 1, b = 1200 (1860 effective) s/mm2, matrix = 64 x 64, field of view = 0.2 x 0.2 cm, resolution = 31 &#956;m).</li>
		<li>Collect a diffusion-weighted time series to determine the stability characteristics of the acute slice preparation. Typical parameters for a two dimensional diffusion weighted image are as follows (TR/TE = 2000/11.6 ms, time = 1.5 h, &#916; = 6 ms, &#948; = 1 ms, averages = 42, b = 1200 s/mm2, matrix = 64 x 64, field of view = 0.2 x 0.2 cm, resolution = 31 &#956;m). Note: Characterizing stability in a given system will vary from the described protocol depending on factors such as the MR contrast employed (e.g. T1,T2, diffusion, susceptibility), the physical perturbation studied, and the MR signal change per unit time resulting from said perturbation.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Aguayo, J. B., Blackband, S. J., Schoeniger, J., Mattingly, M. A., Hintermann, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nuclear+magnetic+resonance+imaging+of+a+single+cell.">Nuclear magnetic resonance imaging of a single cell.</a> Nature. 322, 190-191 (1986).</li><li>Schoeniger, J. S., Aiken, N., Hsu, E., Blackband, S. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Relaxation-time+and+diffusion+NMR+microscopy+of+single+neurons.">Relaxation-time and diffusion NMR microscopy of single neurons.</a> J. Magn. Reson. B. 103, 261-273 (1994).</li><li>Flint, J. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+resonance+microscopy+of+mammalian+neurons.">Magnetic resonance microscopy of mammalian neurons.</a> Neuroimage. 46, 1037-1040 (2009).</li><li>Flint, J. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetic+resonance+microscopy+of+human+and+porcine+neurons+and+cellular+processes.">Magnetic resonance microscopy of human and porcine neurons and cellular processes.</a> Neuroimage. 60, 1404-1411 (2012).</li><li>Kamman, R. L., Go, K. G., Stomp, G. P., Hulstaert, C. E., Berendsen, H. J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Changes+of+Relaxation+times+T1+and+T2+in+rat+tissues+after+biopsy+and+fixation.">Changes of Relaxation times T1 and T2 in rat tissues after biopsy and fixation.</a> Magn. Reson. Imag. 3, 245-250 (1985).</li><li>Shepherd, T. M., Thelwall, P. E., Stanisz, G. J., Blackband, S. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Aldehyde+fixative+solutions+alter+the+water+relaxation+and+diffusion+properties+of+nervous+tissue.">Aldehyde fixative solutions alter the water relaxation and diffusion properties of nervous tissue.</a> Magn. Reson. Med. 62, 26-34 (2009).</li><li>Massin, C., Boero, G., Vincent, F., Abenhaim, J., Besse, P. -. A., Popovic, R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-Q+factor+RF+planar+microcoils+for+micro-scale+NMR+spectroscopy.">High-Q factor RF planar microcoils for micro-scale NMR spectroscopy.</a> Sensor. Actuat. A-Phys. 97, 280-288 (2002).</li><li>Flint, J., Menon, K., Hansen, B., Forder, J., Blackband, S. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+microperfusion+and+in-bore+oxygenator+system+designed+for+magnetic+resonance+microscopy+studies+on+living+tissue+explants.">A microperfusion and in-bore oxygenator system designed for magnetic resonance microscopy studies on living tissue explants.</a> Sci. Rep. 5, 18095 (2015).</li><li>Khong, Y. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Novel+intra-tissue+perfusion+system+for+culturing+thick+liver+tissue.">Novel intra-tissue perfusion system for culturing thick liver tissue.</a> Tissue Eng. 13 (9), 2345-2356 (2007).</li><li>Schumacher, K., Khong, Y. -. M., Chang, S., Ni, J., Sun, W., Yu, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Perfusion+culture+improves+the+maintenance+of+cultured+liver+tissue+slices.">Perfusion culture improves the maintenance of cultured liver tissue slices.</a> Tissue Eng. 13 (1), 197-205 (2007).</li><li>Shepherd, T. M., Blackband, S. J., Wirth, E. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simultaneous+diffusion+MRI+measurements+from+multiple+perfused+rat+hippocampal+slices.">Simultaneous diffusion MRI measurements from multiple perfused rat hippocampal slices.</a> Magn. Reson. Med. 48, 565-569 (2002).</li><li>Henry, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiments+on+the+quantity+of+gases+absorbed+by+water,+at+different+temperatures,+and+under+different+pressures.">Experiments on the quantity of gases absorbed by water, at different temperatures, and under different pressures.</a> Phil. Trans. R. Soc. Lond. 93, (1803).</li><li>Bui, J. D., Buckley, D. L., Phillips, M. I., Blackband, S. J., Bl&#252;mler, P., Bl&#252;mich, B., Botto, R., Fukushima, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Studies+of+perfused+brain+slices+with+MR+microscopy.">Studies of perfused brain slices with MR microscopy.</a> Spatially Resolved Magnetic Resonance. , 337-343 (1998).</li><li>Moseley, M. E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Early+detection+of+regional+cerebral+ischemia+in+cats:+Comparison+of+diffusion-+and+T2-weighted+MRI+and+spectroscopy.">Early detection of regional cerebral ischemia in cats: Comparison of diffusion- and T2-weighted MRI and spectroscopy.</a> Magn. Reson. Med. 14 (2), 330-346 (1990).</li><li>Moseley, M. E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Diffusion-weighted+MR+imaging+of+acute+stroke:+Correlation+with+T2-weighted+and+magnetic+susceptibility-enhanced+MR+imaging+in+cats.">Diffusion-weighted MR imaging of acute stroke: Correlation with T2-weighted and magnetic susceptibility-enhanced MR imaging in cats.</a> Am. J. Neuroradiol. 11, 423-429 (1990).</li></ol>

The authors have no conflicts of interest to disclose.

The current protocol describes procedures necessary for standard metabolic maintenance of acute brain slice preparations undergoing magnetic resonance microscopy. This procedure is the only method currently available that allows visualization of living mammalian tissues with MR at resolutions capable of resolving cells. While the perfusate conditions described are tailored specifically to central nervous system tissues, the protocol is widely adaptable to any manner of living tissue preparation through adjustments of perfusate and gas constituents as well as perfusion flow rate and temperature.
The most common problems likely to be encountered during the described procedures include those related to failures in metabolite supply. Precipitation of calcium salts can occur inside the aCSF during gaseous insufficiency as a result of failures in the bicarbonate buffering system. Such precipitates can clog the perfusion lines and result in severe hardware damage. If salt precipitates are observed in the perfusate following probe assembly, cease perfusion flow immediately by turning off the peristaltic pump. Confirm presence of sufficient sodium bicarbonate levels (4.37 g / 2 L) in perfusate, CO2 levels (5.0%) in supply gas, and carbogen gas flow (1/16 L/min) into both reservoir and oxygenator. Finally, confirm pH levels are stabilized in the physiological range (7.3 - 7.4). In the event that oxygen gas and pH levels are still not regulated appropriately, the gas-exchange membrane should be replaced.
If slices do not exhibit signal stability over the intended experimental time-course, confirm that the correct chemical constituents are present in the aCSF mixture and that the correct osmolality (300 mOsm) and pH (7.3 - 7.4) are maintained. Also, ensure carbogen gas is being supplied to the perfusate reservoir and oxygenator at 1/16 L/min. If these steps do not correct perfusate conditions, replacement of the gas-exchange membrane is advised. If tissue stability is not achieved after troubleshooting the perfusate conditions, consider refinement of the surgical protocol with a focus on minimizing the time interval between tissue harvest and perfusion application.

As magnetic resonance imaging (MRI) systems have steadily progressed to ever-higher field strengths, more details about the composition and status of living tissues have become discernable. Despite such hardware advances, MR imaging at resolutions sufficient to visualize the cellular structures of tissues is still not available in the clinic. As a result, cellular-level characteristics of tissues must be inferred when considering the content of clinical scans. Such inference requires knowledge of equivalent processes gleaned from data taken in model systems which can be observed directly. Traditionally, these models included cells from aquatic organisms such as the Xenopus laevis oocyte and Aplysia californica L7 neuron1,2. These were among the first animal cells available for observation with MR methods due to their atypically large size: approximately 1000 &#956;m and 300 &#956;m diameter, respectively. More recently, advances in hardware design have allowed for one of the largest examples of mammalian cells&#8212;the &#945;-motor neuron&#8212;to be imaged using MR microscopy techniques on fixed tissue3,4. While these studies demonstrated direct visualization of mammalian cellular material using MR, the fixed samples employed differ significantly in their MR properties from live tissue and thus cannot serve as an equivalent representative model5,6. More importantly, observing MR contrast changes that occur in concert with complex biological processes requires living samples that can be perturbed and measured over the course of the imaging experiment.
To facilitate MR microscopy studies on living tissues, a protocol is presented which includes commercial microimaging hardware7 interfaced to a purpose-built, MR compatible, in-bore oxygenator and perfusion device previously described8. Unique advantages of this design include cellular-level resolution capabilities in mammalian tissues and precision control over dissolved gas content and pH at the site of tissue perfusion. Also, unlike the majority of explant MR studies which interrupt perfusion during image acquisition to avoid flow artefacts, this design supports the use of continuous perfusion during data collection which has been shown to improve the physiological condition of isolated tissues9,10. Lastly, its closed recording chamber and slice-retention hardware aid in reducing the likelihood of motion artifacts which could otherwise occur during protracted image collection.
While the current protocol describes procedures appropriate for use with acute hippocampal and cortical slices, precise control over perfusate metabolites enables this system to accommodate a wide array of diverse tissue types and experimental conditions. Limitations of this design include a reduction in sample throughput as compared to a multi-slice perfusion chamber11; however, this limitation may be overcome in the future using multi-coil arrays.
Also, while the described system can be employed in both horizontal or vertical configurations, the current protocol features its use in a vertically oriented, 600 MHz spectrometer. Any system capable of MR microimaging studies&#8212;typically narrow-bore (&#8804;6 cm), high field (&#8805;500 MHz) spectrometers&#8212;will accommodate the oxygenator and perfusion equipment described. However, changes to the imaging coil, gradient, probe system, or other essential imaging hardware employed may necessitate alterations to the perfusion equipment and MR scan parameters.

<table><tbody><tr><td>&lt;strong&gt;Perfusate Preparation&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>Osmette A</td><td>Precision Systems Inc.</td><td>5002</td><td>freezing point depression osmometer</td></tr><tr><td>Stir Plate Type 1000</td><td>Barnstead/Thermodyne</td><td>SPA1025B</td><td>magnetic stir plate with heating element</td></tr><tr><td>Accumet Basic pH Meter</td><td>Fisher Scientific</td><td>AB15</td><td>pH Meter</td></tr><tr><td>pH Probe</td><td>Fisher Scientific</td><td>13-620-AP61</td><td>probe for pH measurement</td></tr><tr><td>Oxygen Meter</td><td>Microelectrodes Inc.</td><td>OM-4</td><td>meter for sampling the oxygen content of gasses or the disolved oxygen content of liquid perfusates</td></tr><tr><td>Oxygen Electrode</td><td>Microelectrodes Inc.</td><td>MI-730</td><td>microprobe for the oxygen meter</td></tr><tr><td>Scale</td><td>Denver Instrument Co.</td><td>A-160</td><td>microscale for weighing chemical components</td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;Slice Preparation&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>Lancer Vibratome</td><td>Ted Pella Inc.</td><td>Series 1000</td><td>vibratory tissue slicer</td></tr><tr><td>Disecting Microscope</td><td>Carl Zeiss Inc.</td><td>OPMI 1-FC</td><td>tabletop, binocular disecting microscope</td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;Perfusion System&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>Masterflex L/S</td><td>Cole-Parmer</td><td>7523-50</td><td>peristaltic micro perfusion pump</td></tr><tr><td>Oxygen Regulators x 2</td><td>Victor Medical</td><td>VMG-05LY</td><td>device for regulating gas flow</td></tr><tr><td>e-sized carbogen cylinders x 2</td><td>Airgas</td><td></td><td>gas tanks containing carbogen gas</td></tr><tr><td>in-bore oxygenator</td><td>developed in house</td><td></td><td>device responsible for pH and oxygen regulation in the perfusate</td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;MR Imaging Hardware&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>Micro Surface Coil (200mm dia., modified)</td><td>Bruker Biospin</td><td>B6371/0001</td><td>four-turn micro (200mm dia) surface-style radiofrequency coil</td></tr><tr><td>Micro 5 probe body</td><td>Bruker Biospin</td><td>Z3395</td><td>microimaging probe used in the 600 MHz spectrometer</td></tr><tr><td>Micro 5 gradient coils</td><td>Bruker Biospin</td><td>M81111</td><td>gradient coil stack used with micro 5 probe body</td></tr><tr><td>600 MHz Spectrometer</td><td>Oxford Instruments</td><td></td><td>superconducting magnet (14.1T) used for MR image generation</td></tr><tr><td>Imaging Console</td><td>Bruker Biospin</td><td>Avance III</td><td>support and control hardware including gradient amplifiers, preamps, &amp;amp; workstation used for MR image generation</td></tr><tr><td>Air Blower</td><td>Bruker Biospin</td><td>BCU-II, -80/60</td><td>Air chiller unit used in conjunction with the probe&#039;s heating coil to regulate temperature inside the magnet bore</td></tr><tr><td>Gradient Chiller</td><td>Thermo Scientific</td><td>Neslab Merlin M33</td><td>Water chiller used to disipate heat generated by the gradient coils</td></tr></tbody></table>

metabolic support of excised, living brain tissues during magnetic resonance microscopy acquisition

This protocol describes the procedures necessary to support normal metabolic functions of acute brain slice preparations during the collection of magnetic resonance (MR) microscopy data. While it is possible to perform MR collections on living, excised mammalian tissue, such experiments have traditionally been constrained by resolution limits and are thus incapable of visualizing tissue microstructure. Conversely, MR protocols that did achieve microscopic image resolution required the use of fixed samples to accommodate the need for static, unchanging conditions over lengthy scan times. The current protocol describes the first available MR technique that enables imaging of living, mammalian tissue samples at microscopic resolutions. Such data is of great importance to the understanding of how pathology-based contrast changes occurring at the microscopic level influence the content of macroscopic MR scans such as those used in the clinic. Once such an understanding is realized, diagnostic methods with greater sensitivity and accuracy can be developed, which will translate directly to earlier disease treatment, more accurate therapy monitoring and improved patient outcomes.
While the described methodology focuses on brain slice preparations, the protocol is adaptable to any excised tissue slice given that changes are made to the gas and perfusate preparations to accommodate the tissue&#39;s specific metabolic needs. Successful execution of the protocol should result in living, acute slice preparations that exhibit MR diffusion signal stability for periods up to 15.5 h. The primary advantages of the current system over other MR compatible perfusion apparatuses are its compatibility with the MR microscopy hardware required to attain higher resolution images and ability to provide constant, uninterrupted flow with carefully regulated perfusate conditions. Reduced sample throughput is a consideration with this design as only one tissue slice may be imaged at a time.

Perfusate Preparation
Upon successful employment of the in-bore oxygenation device, gases present in the supplied carbogen will reach 100% saturation conditions within the aCSF perfusate. This can be demonstrated by varying the oxygen concentration of the supplied gas and measuring the change in dissolved oxygen content in the aCSF perfusate within the perfusion chamber using an oxygen meter (Figure 1)8. According to Henry&#39;s law, the amount of dissolved gas that is in equilibrium with a liquid sample is directly proportional to the partial pressure of that gas provided that the temperature remains constant12. Using this knowledge and precision gas standards, it is possible to quantify the amount of dissolved oxygen contained within an aCSF sample as described. This is achieved by calibrating the oxygen meter using saturated solutions (directly bubbled for 1 h&#160;or more) of aCSF being exposed to gasses of known composition: one gas with high oxygen concentration such as carbogen (95% O2) and another with low oxygen concentration such as nitrogen (0% O2). Afterward, measurements can be taken by submerging the tip of the oxygen electrode into a sample. Confirmation that the in-bore oxygenator is functioning properly can be achieved by measuring the effluent from the perfusion well. The percent dissolved oxygen as measured by the oxygen meter should match the percent concentration of oxygen delivered in the supply gas. If the measured values are lower than those in the supply gas, this would suggest a hardware failure that could lead to metabolic insufficiency in the tissue slice.
Sample Appearance and Behavior
Acute slice preparations that receive perfusion sufficient enough to supply necessary metabolites and carry away metabolic wastes soon reach a state of relative stability. From that point, acute slices can be subjected to external perturbation and their responses to these changes can be measured for scientific study. For MR experiments, tracking the signal of interest over time is a commonly used practice to demonstrate the relative stability of acute slice preparations13. The diffusion-weighted signal is especially sensitive to changes in a tissue&#39;s water mobility, content, and distribution, as can be appreciated by the use of this contrast mechanism to detect infarcts in ischemic stroke14,15. Plotting the normalized diffusion signal over time in acute cortical slices maintained under a variety of perfusion conditions demonstrates relatively stability (2 &#177; 3% over 15.5 h) after tissue isolation is achieved (Figure 5). Diffusion signal stability was maintained regardless of perfusion conditions (intermittent or continuous) or MRI scan length (short [4 min] or long [1.5 h])8. If slices do not exhibit signal stability over time, such as the sharp diffusion signal increase observed in living cortex that did not receive perfusion, this is suggestive of suboptimal experimental conditions. Perturbation experiments should not be attempted prior to confirmation of stable signal conditions in slice preparations.
In addition to signal stability, correct sample positioning must be confirmed at the time of image collection. Even though sample position is controlled during tissue placement at the dissecting microscope, shifts in sample position may occur during the assembly of the perfusion apparatus, or due to rough handling of the coil or probe prior to insertion into the magnet. Confirmation of proper hippocampal placement can be achieved by collecting short (2 min), pilot scans with diffusion contrast (Figure 6). Because the pyramidal cell layer is more sensitive to diffusion weighting than the adjacent hippocampal laminae, this structure will appear as a darker band in diffusion-weighted images. Setups that do not display this characteristic feature contain off-center samples and will likely need to be repeated.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/56282/56282fig1.jpg" /> 
Figure 1: Dissolved oxygen content of aCSF perfusate as a function of percent O2 content in supplied gas. Carbogen mixtures containing variable concentrations of oxygen (95%, 60%, and 19%) are employed as a supply gas. Percent dissolved oxygen readings are then taken from the perfusion well and compared to two known controls: a perfusate reservoir directly bubbled with carbogen (95% O2), and a perfusate reservoir exposed to atmospheric conditions (23% O2). In each case, the percent oxygen saturation at the site of tissue perfusion approaches 100% of the O2 concentration within the carbogen mixture used. Error bars are equal to the standard deviation of the sample means. Figure reproduced with permission from the original article8. <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/56282/56282fig2.jpg" /> 
Figure 2: Schematic drawing of the in-bore oxygenator and perfusion chamber. This diagram shows detailed design elements responsible for the function of these critical devices. Fresh perfusate that has been pumped through a bubble trap enters the oxygenator through the top of a 10 mm NMR tube. In doing so, it transitions into a highly gas permeable silicone tubing (blue segment) that is coiled around an open-ended, 5 mm NMR tube nested inside. Carbogen gas supplied through the top of the 5mm tube enters the chamber through the open-ended bottom and passes over the coiled silicone tubing before exiting the oxygenator through a vent hole in the 10 mm tube cap. During this exposure, the perfusate flowing through the silicone tube becomes saturated with the chemical components of the supplied gas mixture. Upon exiting the oxygenator, perfusate passes directly into the perfusion chamber before entering the return line leading to a waste collection reservoir. Other components critical to this design include the acetal support peg which allows the oxygenator to stand vertically atop the modified RF microcoil, a silicone washer (red ring) which forms the liquid-tight seal between the oxygenator&#39;s perfusion chamber and the microcoil&#39;s tissue well, and the cable tie notch which accommodates placement of a cable tie used to form this reversible seal. This figure has been modified and reproduced with permission from the original article8. <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/56282/56282fig3.jpg" /> 
Figure 3: Modifications to the microcoil assembly which permit interface to the in-bore oxygenator. Two grooves 3.0 mm x 1.5 mm (black arrows) were cut into the side of the assembly that accommodate the width of a cable tie used to seal the perfusion chamber. A channel (15 mm x 3 mm x 4 mm) connects the groves across the back face of the coil. Two nylon spaces placed in the sides of the channel (red arrows) act as a catch for the cable tie head which eases the sealing procedure. A hole (2 mm x 14 mm) drilled in the top of the coil assembly (yellow arrow) joins to the acetal support peg to secure the oxygenator. This figure has been modified and reproduced with permission from the original article8. <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/56282/56282fig4.jpg" /> 
Figure 4: Photo montage detailing the relative placement and proper assembly of microcoil, oxygenator, and probe components. These images feature key hardware components of the in-bore oxygenator and microperfusion device and illustrate how the separate parts interface with one another. (A) Exploded-view photo showing the relative placement of all components prior to sealing of the tissue well or assembly of the probe body. Care has been taken to display the relative location of parts accurately; however, a section of the perfusion lines has been doubled back in this series so that all components fit within the image frame. (1 = probe head, 2 = microcoil assembly, 3 = nylon tissue retention ring, 4 = perfusion well, 5 = cable tie, 6 = in-bore oxygenator, 7 = gradient coils, 8 = bubble trap). (B) Components following coil and oxygenator assembly. In this image, the nylon retention ring has been placed within the microcoil&#39;s tissue well to secure a sample. The acetal support peg on the base of the oxygenator has been secured in the corresponding hole on top of the microcoil. The silicone gasket on the open end of the perfusion well has been placed over the tissue well, and a cable tie has been tightened around these components to seal the perfusion chamber. Lastly, the base of the microcoil has been connected to the top of the probe head. (C) Components following probe assembly. In the last panel, excess length from the cable tie has been trimmed flush with the microcoil. The gradient coil stack is then slid into position by carefully advancing the cylinder towards the probe while passing the excess perfusion lines, oxygenator, and microcoil through its hollow center. Once the gradients are connected to the probe head, they&#39;re held in place by screwing the securing collar on the probe over the threaded base of the gradients. <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/56282/56282fig5.jpg" /> 
Figure 5: Diffusion signal stability in superfused acute cortical slices. (A) Normalized diffusion signal values in four acute slices subjected to differing superfusion paradigms are plotted over time for a period of up to 21.5 h following euthanasia. Slices remain within &#177; 5% of their initial diffusion signal measurement for a period of 15.5 h following euthanasia regardless of whether superfusion is continuous or intermittent and independent of the MR scan length (1.5 h or 4 min). Signal recordings taken from formaldehyde-fixed cortex serve as the positive control (n = 1) for stability due to the static, unchanging nature of fixed tissue samples. Conversely, diffusion signal measured in a live slice absent of superfusion support (n = 1) serves as a control for metabolic deficiency. Experiment parameters of the different superfusion trials are as follows: continuous (superfusion always on, time per scan = 1.5 h), intermittent (superfusion on for 10 min interval between scans, time per scan = 1.5 h), Long interval, long scan (superfusion on during scan, but paused for 10 min between scans, time per scan = 1.5 h), Long interval, short scan (superfusion on for 1.5 h interval between scans, time per scan = 4 min). (B) Analyzed data showing group means of the four live-slice superfusion experiments from panel (A). The diffusion signal profile from the grouped, superfused cortical slices exhibits little variation over time (2 &#177; 3% over 15.5 h) whereas the non-perfused control (n = 1) exhibits dramatic signal instability early in the experiment (15% by 6.5 h). This figure has been modified and reproduced with permission from the original article8. <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/56282/56282fig6.jpg" /> 
Figure 6: Confirmation of hippocampal slice placement during pilot imaging. Prior to running an extended MR microscopy session, correct placement of the sample is critical to ensure resources such as scanner time and expensive perfusate additives are not wasted. The pyramidal cell layer in the CA1 region of the hippocampus can be visualized in faster (4.3 min), lower resolution (31 &#956;m x 31 &#956;m in-plane) pilot scans to ensure the tissue of interest is placed correctly in relation to the micro-coil. Scan parameters common to both images are as follows: TR/TE = 2000/11.6 ms, &#916; = 6 ms, &#948; = 1 ms, averages = 1. (A) b = 0 (227 effective) s/mm2. In this preliminary scan, the stratum pyramidale is only just visible as a grey, diagonal band centered in the coil&#39;s excitation profile. (B) b = 1,200 (1,860 effective) s/mm2. At higher diffusion weighting, interlamellar contrast increases as the pyramidal cell layer becomes darker than tissues in the adjacent laminae (above: stratum oriens; below: stratum radiatum). <a href="https://cloudflare.jove.com/files/ftp_upload/56282/56282fig6large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Metabolic Support of Excised, Living Brain Tissues During Magnetic Resonance Microscopy Acquisition at JoVE.com

Metabolic Support of Excised, Living Brain Tissues During Magnetic Resonance Microscopy Acquisition

The current protocol describes a method by which users can maintain viability of acute hippocampal and cortical slice preparations during the collection of magnetic resonance microscopy data.

This protocol describes the procedures necessary to support normal metabolic functions of acute brain slice preparations during the collection of magnetic ...

metabolic-support-excised-living-brain-tissues-during-magnetic

Research

JoVE Journal

Bioengineering

6.0K Views.  University of Florida. The current protocol describes a method by which users can maintain viability of acute hippocampal and cortical slice preparations during the collection of magnetic resonance microscopy data.

Video: Metabolic Support of Excised, Living Brain Tissues During Magnetic Resonance Microscopy Acquisition

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring 

Nanomedications can be carried by blood borne monocyte-macrophages into the reticuloendothelial system (RES; spleen, liver, lymph nodes) and to end organs. The latter include the lung, RES, and brain and are operative during human immunodeficiency virus type one (HIV-1) infection. Macrophage entry into tissues is notable in areas of active HIV-1 replication and sites of inflammation. In order to assess the potential of macrophages as nanocarriers, superparamagnetic iron-oxide and/or drug laden particles coated with surfactants were parenterally injected into HIV-1 encephalitic mice. This was done to quantitatively assess particle and drug biodistribution. Magnetic resonance imaging (MRI) test results were validated by histological coregistration and enhanced image processing. End organ disease as typified by altered brain histology were assessed by MRI. The demonstration of robust migration of nanoformulations into areas of focal encephalitis provides '"proof of concept" for the use of advanced bioimaging techniques to monitor macrophage migration. Importantly, histopathological aberrations in brain correlate with bioimaging parameters making the general utility of MRI in studies of cell distribution in disease feasible. We posit that using such methods can provide a real time index of disease burden and therapeutic efficacy with translational potential to humans.

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring

Bioimaging methods used to assess cell biodistribution of nanoparticles are applicable for therapeutic and diagnostic monitoring of nanoformulated compounds. The methods described herein are sensitive and specific when assessed by histological coregistration. The methodologies provide a translational pathway from rodent to human applications.

Nanomedications can be carried by blood borne monocyte-macrophages into the reticuloendothelial system (RES; spleen, liver, lymph nodes) and to end ...

Multiple-mouse Neuroanatomical Magnetic Resonance Imaging

The field of mouse phenotyping with magnetic resonance imaging (MRI) is rapidly growing, motivated by the need for improved tools for characterizing and evaluating mouse models of human disease. MRI is an excellent modality for investigating genetically altered animals. It is capable of whole brain coverage, can be used in vivo, and provides multiple contrast mechanisms for investigating different aspects of neuranatomy and physiology. The advent of high-field scanners along with the ability to scan multiple mice simultaneously allows for rapid phenotyping of novel mutations.
Effective mouse MRI studies require attention to many aspects of experiment design. In this article, we will describe general methods to acquire quality images for mouse phenotyping using a system that images mice concurrently in shielded transmit/receive radio frequency (RF) coils in a common magnet (Bock et al., 2003). We focus particularly on anatomical phenotyping, an important and accessible application that has shown a high potential for impact in many mouse models at our imaging centre. Before we can provide the detailed steps to acquire such images, there are important practical considerations for both in vivo brain imaging (Dazai et al., 2004) and ex vivo brain imaging (Spring et al., 2007) that should be noted. These are discussed below.

Magnetic resonance imaging (MRI) has become an increasingly popular tool for examining the phenotype of genetically altered mice. This article illustrates the methods necessary to achieve high-throughput phenotyping of genetically altered mice using multiple-mouse MRI.

The field of mouse phenotyping with magnetic resonance imaging (MRI) is rapidly growing, motivated by the need for improved tools for characterizing and ...

Neuroscience

Noninvasive In Vivo Small Animal MRI and MRS: Basic Experimental Procedures

Small animal Magnetic Resonance (MR) research has emerged as an important element of modern biomedical research due to its non-invasive nature and the richness of biological information it provides. MR does not require any ionizing radiation and can noninvasively provide higher resolution and better signal-to-noise ratio in comparison to other tomographic or spectroscopic modalities. In this protocol, we will focus on small animal MR imaging and MR spectroscopy (MRI/MRS) to noninvasively acquire relaxation weighted 1H images of mouse and to obtain 31P spectra of mouse muscle. This work does not attempt to cover every aspect of small animal MRI/MRS but rather introduces basic procedures of mouse MRI/MRS experiments. The main goal of this work is to inform researchers of the basic procedures for in vivo MR experiments on small animals. The goal is to provide a better understanding of basic experimental procedures to allow researchers new to the MR field to better plan for non-MR components of their studies so that both MR and non-MR procedures are seamlessly integrated.

Noninvasive In Vivo Small Animal MRI and MRS: Basic Experimental Procedures

This work describes basic procedures of noninvasive small animal MRI and MRS in vivo.

Small animal Magnetic Resonance (MR) research has emerged as an important element of modern biomedical research due to its non-invasive nature and the ...

Biology

The Use of Magnetic Resonance Spectroscopy as a Tool for the Measurement of Bi-hemispheric Transcranial Electric Stimulation Effects on Primary Motor Cortex Metabolism

Transcranial direct current stimulation (tDCS) is a neuromodulation technique that has been increasingly used over the past decade in the treatment of neurological and psychiatric disorders such as stroke and depression. Yet, the mechanisms underlying its ability to modulate brain excitability to improve clinical symptoms remains poorly understood 33. To help improve this understanding, proton magnetic resonance spectroscopy (1H-MRS) can be used as it allows the in vivo quantification of brain metabolites such as &#947;-aminobutyric acid (GABA) and glutamate in a region-specific manner 41. In fact, a recent study demonstrated that 1H-MRS is indeed a powerful means to better understand the effects of tDCS on neurotransmitter concentration 34. This article aims to describe the complete protocol for combining tDCS (NeuroConn MR compatible stimulator) with 1H-MRS at 3 T using a MEGA-PRESS sequence. We will describe the impact of a protocol that has shown great promise for the treatment of motor dysfunctions after stroke, which consists of bilateral stimulation of primary motor cortices 27,30,31. Methodological factors to consider and possible modifications to the protocol are also discussed.

This article aims to describe a basic protocol for combining transcranial direct current stimulation (tDCS) with proton magnetic resonance spectroscopy (1H-MRS) measurements to investigate the effects of bilateral stimulation on primary motor cortex metabolism.

Transcranial direct current stimulation (tDCS) is a neuromodulation technique that has been increasingly used over the past decade in the treatment of ...

Metabolomic Analysis of Rat Brain by High Resolution Nuclear Magnetic Resonance Spectroscopy of Tissue Extracts

Studies of gene expression on the RNA and protein levels have long been used to explore biological processes underlying disease. More recently, genomics and proteomics have been complemented by comprehensive quantitative analysis of the metabolite pool present in biological systems. This strategy, termed metabolomics, strives to provide a global characterization of the small-molecule complement involved in metabolism. While the genome and the proteome define the tasks cells can perform, the metabolome is part of the actual phenotype. Among the methods currently used in metabolomics, spectroscopic techniques are of special interest because they allow one to simultaneously analyze a large number of metabolites without prior selection for specific biochemical pathways, thus enabling a broad unbiased approach. Here, an optimized experimental protocol for metabolomic analysis by high-resolution NMR spectroscopy is presented, which is the method of choice for efficient quantification of tissue metabolites. Important strengths of this method are (i) the use of crude extracts, without the need to purify the sample and/or separate metabolites; (ii) the intrinsically quantitative nature of NMR, permitting quantitation of all metabolites represented by an NMR spectrum with one reference compound only; and (iii) the nondestructive nature of NMR enabling repeated use of the same sample for multiple measurements. The dynamic range of metabolite concentrations that can be covered is considerable due to the linear response of NMR signals, although metabolites occurring at extremely low concentrations may be difficult to detect. For the least abundant compounds, the highly sensitive mass spectrometry method may be advantageous although this technique requires more intricate sample preparation and quantification procedures than NMR spectroscopy. We present here an NMR protocol adjusted to rat brain analysis; however, the same protocol can be applied to other tissues with minor modifications.

The neurochemistry of mammalian brain is changed in many neurological and systemic diseases. Characteristic profiles of cerebral metabolites can be efficiently obtained based on crude extracts of brain tissue. To this end, high-resolution NMR spectroscopy is employed, enabling detailed quantitative analysis of metabolite concentrations (metabolomics).

Studies of gene expression on the RNA and protein levels have long been used to explore biological processes underlying disease. More recently, genomics ...

High-resolution Structural Magnetic Resonance Imaging of the Human Subcortex In Vivo and Postmortem

The focus of this study was to test the resolution limits of structural MRI of a postmortem brain compared to living human brains. The resolution of structural MRI in vivo is ultimately limited by physiological noise, including pulsation, respiration and head movement. Although imaging hardware continues to improve, it is still difficult to resolve structures on the millimeter scale. For example, the primary visual sensory pathways synapse at the lateral geniculate nucleus (LGN), a visual relay and control nucleus in the thalamus that normally is organized into six interleaved monocular layers. Neuroimaging studies have not been able to reliably distinguish these layers due their small size that are less than 1 mm thick.
The resolving limit of structural MRI, in a postmortem brain was tested using multiple images averaged over a long duration (~24 h). The purpose was to test whether it was possible to resolve the individual layers of the LGN in the absence of physiological noise. A proton density (PD)1 weighted pulse sequence was used with varying resolution and other parameters to determine the minimum number of images necessary to be registered and averaged to reliably distinguish the LGN and other subcortical regions. The results were also compared to images acquired in living human brains. In vivo subjects were scanned in order to determine the additional effects of physiological noise on the minimum number of PD scans needed to differentiate subcortical structures, useful in clinical applications.

High-resolution Structural Magnetic Resonance Imaging of the Human Subcortex In Vivo and Postmortem

Here we present a protocol to determine the minimum number images that needed to be registered and averaged to resolve subcortical structures and test whether the individual layers of the LGN could be resolved in the absence of physiological noise.

The focus of this study was to test the resolution limits of structural MRI of a postmortem brain compared to living human brains. The resolution of ...

Utilizing 3D Printing Technology to Merge MRI with Histology: A Protocol for Brain Sectioning

Magnetic resonance imaging (MRI) allows for the delineation between normal and abnormal tissue on a macroscopic scale, sampling an entire tissue volume three-dimensionally. While MRI is an extremely sensitive tool for detecting tissue abnormalities, association of signal changes with an underlying pathological process is usually not straightforward. In the central nervous system, for example, inflammation, demyelination, axonal damage, gliosis, and neuronal death may all induce similar findings on MRI. As such, interpretation of MRI scans depends on the context, and radiological-histopathological correlation is therefore of the utmost importance. Unfortunately, traditional pathological sectioning of brain tissue is often imprecise and inconsistent, thus complicating the comparison between histology sections and MRI. This article presents novel methodology for accurately sectioning primate brain tissues and thus allowing precise matching between histology and MRI. The detailed protocol described in this article will assist investigators in applying this method, which relies on the creation of 3D printed brain slicers. Slightly modified, it can be easily implemented for brains of other species, including humans.

The overall goal of this protocol is to accurately align magnetic resonance imaging (MRI) image volumes with histology sections via the creation of customized 3D-printed brain holders and slicer boxes.

Magnetic resonance imaging (MRI) allows for the delineation between normal and abnormal tissue on a macroscopic scale, sampling an entire tissue volume ...

3D Scanning Technology Bridging Microcircuits and Macroscale Brain Images in 3D Novel Embedding Overlapping Protocol

The human brain, being a multiscale system, has both macroscopic electrical signals, globally flowing along thick white-matter fiber bundles, and microscopic neuronal spikes, propagating along axons and dendrites. Both scales complement different aspects of human cognitive and behavioral functions. At the macroscopic level, MRI has been the current standard imaging technology, in which the smallest spatial resolution, voxel size, is 0.1&#8211;1 mm3. Also, at the microscopic level, previous physiological studies were aware of nonuniform neuronal architectures within such voxels. This study develops a powerful way to accurately embed microscopic data into a macroscopic map by interfacing biological scientific research with technological advancements in 3D scanning technology. Since 3D scanning technology has mostly been used for engineering and industrial design until now, it is repurposed for the first time to embed microconnectomes into the whole brain while preserving natural spiking in living brain cells. In order to achieve this purpose, first, we constructed a scanning protocol to obtain accurate 3D images from living bio-organisms inherently challenging to image due to moist and reflective surfaces. Second, we trained to keep speed to prevent the degradation of living brain tissue, which is a key factor in retaining better conditions and recording more natural neuronal spikes from active neurons in the brain tissue. Two cortical surface images, independently extracted from two different imaging modules, namely MRI and 3D scanner surface images, surprisingly show a distance error of only 50 &#956;m as mode value of the histogram. This accuracy is comparable in scale to the microscopic resolution of intercellular distances; also, it is stable among different individual mice. This new protocol, the 3D novel embedding overlapping (3D-NEO) protocol, bridges macroscopic and microscopic levels derived by this integrative protocol and accelerates new scientific findings to study comprehensive connectivity architectures (i.e., microconnectome).

This article introduces an experimental protocol using 3D scanning technology bridging two spatial scales: the macroscopic spatial scale of whole-brain anatomy imaged by MRI at &#62;100 &#956;m and the microscopic spatial scale of neuronal distributions using immunohistochemistry staining and a multielectrode array system and other methods (~10 &#956;m).

The human brain, being a multiscale system, has both macroscopic electrical signals, globally flowing along thick white-matter fiber bundles, and ...

Functional Magnetic Resonance Spectroscopy at 7 T in the Rat Barrel Cortex During Whisker Activation

Nuclear magnetic resonance (NMR) spectroscopy offers the opportunity to measure cerebral metabolite contents in vivo and noninvasively. Thanks to technological developments over the last decade and the increase in magnetic field strength, it is now possible to obtain good resolution spectra in vivo in the rat brain. Neuroenergetics (i.e., the study of brain metabolism) and, especially, metabolic interactions between the different cell types have attracted more and more interest in recent years. Among these metabolic interactions, the existence of a lactate shuttle between neurons and astrocytes is still debated. It is, thus, of great interest to perform functional proton magnetic resonance spectroscopy (1H-MRS) in a rat model of brain activation and monitor lactate. However, the methyl lactate peak overlaps lipid resonance peaks and is difficult to quantify. The protocol described below allows metabolic and lactate fluctuations to be monitored in an activated brain area. Cerebral activation is obtained by whisker stimulation and 1H-MRS is performed in the corresponding activated barrel cortex, whose area is detected using blood-oxygen-level-dependent functional magnetic resonance imaging (BOLD fMRI). All steps are fully described: the choice of anesthetics, coils, and sequences, achieving efficient whisker stimulation directly in the magnet, and data processing.

After checking by blood-oxygen-level-dependent functional magnetic resonance imaging (BOLD fMRI) that the corresponding somatosensory barrel field cortex area (called S1BF) is correctly activated, the main goal of this study is to quantify lactate content fluctuations in the activated rat brains by localized proton magnetic resonance spectroscopy (1H-MRS) at 7 T.

Nuclear magnetic resonance (NMR) spectroscopy offers the opportunity to measure cerebral metabolite contents in vivo and noninvasively. Thanks to ...

Comprehensive Autopsy Program for Individuals with Multiple Sclerosis

We describe a rapid tissue donation program for individuals with multiple sclerosis (MS) that requires scientists and technicians to be on-call 24/7, 365 days a year. Participants consent to donate their brain and spinal cord. Most patients were followed by neurologists at the Cleveland Clinic Mellen Center for MS Treatment and Research. Their clinical courses and neurological disabilities are well-characterized. Soon after death, the body is transported to the MS Imaging Center, where the brain is scanned in situ by 3 T magnetic resonance imaging (MRI). The body is then transferred to the autopsy room, where the brain and spinal cord are removed. The brain is divided into two hemispheres. One hemisphere is immediately placed in a slicing box and alternate 1 cm-thick slices are either fixed in 4% paraformaldehyde for two days or rapidly frozen in dry ice and 2-methylbutane. The short-fixed brain slices are stored in a cryopreservation solution and used for histological analyses and immunocytochemical detection of sensitive antigens. Frozen slices are stored at -80 &#176;C and used for molecular, immunocytochemical, and in situ hybridization/RNA scope studies. The other hemisphere is placed in 4% paraformaldehyde for several months, placed in the slicing box, re-scanned in the 3 T magnetic resonance (MR) scanner and sliced into centimeter-thick slices. Postmortem in situ MR images (MRIs) are co-registered with 1 cm-thick brain slices to facilitate MRI-pathology correlations. All brain slices are photographed and brain white-matter lesions are identified. The spinal cord is cut into 2 cm segments. Alternate segments are fixed in 4% paraformaldehyde or rapidly frozen. The rapid procurement of postmortem MS tissues allows pathological and molecular analyses of MS brains and spinal cords and pathological correlations of brain MRI abnormalities. The quality of these rapidly-processed postmortem tissues (usually within 6 h of death) is of great value to MS research and has resulted in many high-impact discoveries.

Multiple sclerosis is an inflammatory demyelinating disease with no cure. Analysis of brain tissue provides important clues to understanding the pathogenesis of the disease. Here we discuss the methodology and downstream analysis of MS brain tissue collected through a unique rapid autopsy program in operation at the Cleveland Clinic.

We describe a rapid tissue donation program for individuals with multiple sclerosis (MS) that requires scientists and technicians to be on-call 24/7, 365 ...

Metabolic Support of Excised, Living Brain Tissues During Magnetic Resonance Microscopy Acquisition

Summary

Explore More Videos

Chapters in this video

Registered Bioimaging of Nanomaterials for Diagnostic and Therapeutic Monitoring

Multiple-mouse Neuroanatomical Magnetic Resonance Imaging

Noninvasive In Vivo Small Animal MRI and MRS: Basic Experimental Procedures

The Use of Magnetic Resonance Spectroscopy as a Tool for the Measurement of Bi-hemispheric Transcranial Electric Stimulation Effects on Primary Motor Cortex Metabolism

Metabolomic Analysis of Rat Brain by High Resolution Nuclear Magnetic Resonance Spectroscopy of Tissue Extracts

High-resolution Structural Magnetic Resonance Imaging of the Human Subcortex In Vivo and Postmortem

Utilizing 3D Printing Technology to Merge MRI with Histology: A Protocol for Brain Sectioning

3D Scanning Technology Bridging Microcircuits and Macroscale Brain Images in 3D Novel Embedding Overlapping Protocol

Functional Magnetic Resonance Spectroscopy at 7 T in the Rat Barrel Cortex During Whisker Activation

Comprehensive Autopsy Program for Individuals with Multiple Sclerosis