The authors are thankful to Ms. Elena Denks for her technical assistance.

This study was approved by the Ethics Committee of the medical faculty of the University Hospital Magdeburg (application number 88/18) and the subjects provided written informed consent prior to the blood drawing procedure.
1. Heparin stock preparation and blood sampling
<ol>
	<li>Calculate the amount of blood needed for the entire experiments. 
	NOTE: Almost, 5 mL of heparinized blood is required for each vascular device in duplicates (loops). Likewise, 5 mL of blood is required for each baseline and static condition which is kept aside at room temperature.</li>
	<li>Prepare a heparin stock solution at the concentration of 100 IU/mL by diluting the unfractionated heparin (e.g., Rotexmedia) in deionized water. Use 150 &#181;L of this solution for the heparinization of 10 mL fresh blood.</li>
	<li>Calculate the amount of blood as well as plasma that are needed for whole blood cell count, ELISA and FACS assays. 
	NOTE: The measurements represented in this study are obtained from two loops running in parallel (one as duplicate) with a total blood volume of 10 mL.</li>
	<li>Based on the required amount of blood, fill 10 mL syringes with 150 &#181;L of heparin stock solution to prevent blood coagulation with a final heparin concentration of 1.5 IU/mL blood.</li>
	<li>Draw blood using a butterfly (size: 21 G). Fill the syringes very gently to avoid hemolysis or cell activation due to excessive vacuum. 
	NOTE: Permission from the local ethical committee should be obtained before the commencement of the experiments. Obtain informed consent from each human blood donor. Ensure that the blood donor is healthy and does not take any medication, especially no antiplatelet agents or non-steroidal anti-inflammatory drugs for at least 10 days prior to the experiments. Of note, same donor is preferred when comparing different types of vascular devices for the first time as presented in this manuscript. To further evaluate the inter-individual differences, the protocol can be repeated with different donors.</li>
	<li>Collect blood in a glass beaker, avoid excessive agitation.</li>
</ol>
2. In vitro hemodynamic loop assembly
<ol>
	<li>Fill the water bath until the water level reaches up to the center of the rotation unit. Set water temperature to 37 &#176;C.</li>
	<li>Loop assembly for testing different tubing materials (polyPVC, hepPVC, PVC and latex)
	<ol>
		<li>Cut two 50 cm long pieces of each tube material (inner diameter 5 mm) with the tube cutter. Ensure that the cutting surface is flat, as this is particularly important for perfect closure for the loops with small diameters so that blood flows without any distortion on the fitting edge. 
		NOTE: This entire protocol utilizes the tubes with an inner diameter of 5 mm.</li>
		<li>To ease the handling and to avoid post-sample processing delay after rotation, run only four loops (2 materials in duplicates) in parallel.</li>
		<li>To generate a loop shape, plug the open endings of the tubes into a short piece of silicon tube fitting the outer diameter of the investigative tube.</li>
		<li>Use the polycarbonate tension bands to ensure proper closing of the loops. When used for the first time, adjust the length of the bands to fit the outer diameter of the loop by cutting the tension band with scissors in required lengths and secure it with a 3 mm torque wrench.</li>
		<li>Carefully tighten the locking screw of the tension band connector under inspection of the tube endings. Adjust the closing force so that no gap remains between the tube endings. If the locking screw is totally tightened and the tension of the polycarbonate band seems too low to close the gap between the tube endings, open the locking the system and cut a few mm of the tension band. Repeat this, until accurate loop closure is achieved (Figure 1A).</li>
		<li>If the tubing material is very soft and tends to slip inside the tension bands, fix the loop with electrical tape to the tension band (Figure 1B,C).</li>
		<li>Prepare an additional loop of PVC for temperature control with the same dimensions as the test loops.</li>
		<li>Secure the loops in the loop cradle of the rotation unit outside the water bath. Thereafter, attach the loop cradle to the rotation unit inside the water bath (Figure 1E).</li>
		<li>Dismantle the tension band partly from the loops and unplug one end of each tube to open the loop.</li>
		<li>Gently fill each loop with 5 mL of blood with a 5 mL serological pipette. Mix blood gently twice in the glass beaker by slowly pipetting up and down before loading into the loops.</li>
		<li>Take the disposable thermometer and place it inside the temperature control loop. If the thermometer is too large, cut it with scissors to fit smaller tubes. Fill the loop with 5 mL of deionized water at room temperature.</li>
		<li>Close the loops and ensure whether the loops, the tension bands and the rack are properly fitted.</li>
		<li>Set rotation speed to 30 rounds per minute (rpm) and rotate for 3 h.</li>
	</ol>
	</li>
	<li>Loop assembly for testing the impact of improper loop closure (gap)
	<ol>
		<li>Prepare four loops (polyPVC) as described in 2.2.</li>
		<li>Close two of the loops properly with the tension bands and avoid any gap between the tube endings.</li>
		<li>For the other two loops plug the open endings into the bigger tube as described in 2.2.3, but leave a gap of 1-2 mm in between the loop endings. Do not use the tension bands for these loops (Figure 1D).</li>
		<li>Prepare one temperature control loop as described in 2.2.7 and 2.2.11.</li>
		<li>Fill all loops with blood as described in 2.2.10.</li>
		<li>Set the rotation speed to 30 rpm and rotate for 3 h.</li>
	</ol>
	</li>
	<li>Loop assembly for stent testing
	<ol>
		<li>Prepare four loops as described in 2.2 and following. 
		NOTE: To assess the blood biocompatibility of stents, the tubing material itself should be tested to be biocompatible in order to prevent masking of cell activation. If no data exists, the tube material itself can be tested as described in 2.2. Furthermore, the diameter range within the stent can be applied (see manufacturer&#8217;s instructions) and should fit the inner diameter of the tube material.</li>
		<li>Open two of the loops and take the tube out of the tension band system.</li>
		<li>Insert the stent into the middle of the tube as per the manufacturer&#8217;s instructions.</li>
		<li>Use the other two loops without stent as control. Fill all loops with blood as described in 2.2.10.</li>
		<li>Set rotation speed to 30 rpm and rotate for 3 h.</li>
	</ol>
	</li>
	<li>Temperature control
	<ol>
		<li>At any time during duration and when rotation is stopped, the temperature of the blood inside the loops is indicated by the thermometer inside the temperature control loop. To read off the temperature, stop the rotation and immediately read off the temperature indicated by the thermometer.</li>
	</ol>
	</li>
</ol>
3. Blood sample processing
<ol>
	<li>After rotation, let the loops stand in the rack for 2 min in an upward position to let the blood accumulate at the bottom of the loops, avoiding any spilling while opening the loops.</li>
	<li>Inspect the blood left for static conditions: If this blood is coagulated, an improper heparinization is ultimately suspected. In this case, repeat the experiment preferably also with another blood donor.</li>
	<li>Carefully take the loops out of the rack. Open the connectors and let the blood flow into a 10 mL glass beaker.</li>
	<li>Pool the blood from the tubes that are run in duplicates.</li>
	<li>Draw fresh blood for baseline analysis from the same donor as described in 1.5 and 1.6.</li>
	<li>Collection of sodium citrate blood
	<ol>
		<li>For the collection of sodium citrate blood, fill four 1.5 mL tubes, each with 111 &#181;L sodium citrate solution collected from sodium citrate tubes, to generate a final concentration of 3.2% of sodium citrate.</li>
		<li>Fill each tube with 1 mL of blood from the glass beakers as described in 1.6 and 3.3.</li>
		<li>Keep the blood at room temperature and use the this blood for FACS analyses as described in 12. 
		NOTE: To change the length of the loops for different experimental setups, properly plan aliquots based on the amount of measurements to be made. It may be necessary to establish all required measurements with fresh blood prior to the real experiments to ensure the volume of blood in the loops is enough for all measurements.</li>
	</ol>
	</li>
	<li>Collection of ethylenediaminetetraacetic acid (EDTA) blood and plasma samples.
	<ol>
		<li>From each glass beaker with blood (see 1.6 and 3.3) transfer 4.5 ml of blood into one 5 ml EDTA tube. Fill two EDTA tubes from each 10 ml glass beaker with blood.</li>
		<li>Gently mix the blood and keep it on ice.</li>
		<li>Transfer 2 mL of blood into a 2 mL locking centrifugation tube and use this blood for blood cell count and free hemoglobin measurement as described in 5. And 6.</li>
		<li>Centrifuge the remaining blood at 3,500 x g for 20 min.</li>
		<li>Carefully collect the plasma in the supernatant in 500 &#181;L aliquots and immediately freeze at -80 &#176;C.</li>
	</ol>
	</li>
</ol>
4. Scanning electron microscopy and &#181;CT images
<ol>
	<li>After blood sample processing, rinse the emptied loops prepared as described in 2.3 with 10 mL of phosphate-buffered saline (PBS) each.</li>
	<li>Carefully cut off a 1 cm long sample from each end of each tube with a scalpel.</li>
	<li>Incubate sample overnight at 4 &#176;C in a 2% glutaraldehyde solution. 
	CAUTION: Inhalation of aldehyde vapors can cause nasal symptoms such as a runny nose ore persistent stuffiness and airway irritation, and contact with skin causes dermatitis. Aldehydes should be handled in a fume-hood while wearing gloves, a protective gown and safety goggles.</li>
	<li>Rinse the sample (3 times) with PBS.</li>
	<li>Prepare a 1% solution of osmium tetroxide (OsO4) in deionized water and incubate sample for 15 min at room temperature. 
	CAUTION: OsO4 is a strong oxidizing agent, it can be reduced by exposure to light. To avoid the reduction during preparation, store OsO4 in a brown glass bottle. OsO4 is extremely volatile, its fumes are toxic to eyes, nose and throat. Always work under a fume-hood and use gloves and protecting clothing, ensuring that no part of the body is exposed to OsO4. Contact your institution&#8217;s guidelines regarding handling of waste disposal and storage. In general, OsO4 is storable for several months, but it needs special glass bottles with Teflon liner and a desiccator, because OsO4 can discolor internal surfaces and contents of the refrigerator in the presence of leaking fumes.</li>
	<li>Take out samples, transfer them in a new 15 mL centrifuge tubes and rinse samples 3 times with PBS.</li>
	<li>Prepare a series of ethanol with varying concentrations (25%, 50%, 75%, 95%, 100%)</li>
	<li>Dehydrate samples in ethanol: incubate for 20 min each in 25%, 50%, 75% and 90% and 30 min in 100%.</li>
	<li>Take samples out of 100% ethanol and let it air dry overnight at room temperature.</li>
	<li>Examine samples in the scanning electron microscope at an acceleration voltage of 5 kV and with the X-ray &#181;CT scanner.</li>
</ol>
5. Blood cell count
<ol>
	<li>Take 2 mL of the EDTA blood obtained as described in 3.7.3</li>
	<li>Insert the tube into the automated hematology analyzer and follow the manufacturer&#8217;s instructions.</li>
</ol>
6. Measurement of free hemoglobin (fHb) in plasma
<ol>
	<li>Thaw one plasma sample from each condition obtained as described in 3.7.5. Store on ice after thawing. 
	NOTE: Always thaw frozen plasma samples in a water bath at 37 &#176;C and immediately transfer to ice, containing some water, to lower the temperature. This is important to avoid activation of blood components during thawing.</li>
	<li>Use the fHb reagent and follow the manufacturer&#8217;s instructions. Avoid contamination after opening and protect the reagent from direct light (sun, UV light).</li>
	<li>Use a pipetting scheme (see manufacturer&#8217;s instructions) with 1:5 dilution.</li>
	<li>Add 1000 &#181;L of the hemoglobin reagent in a 1.6 mL semi-micro cuvette. Use this cuvette to determine the blank value.</li>
	<li>Add 1000 &#181;L of the hemoglobin reagent and 250 &#181;L of the plasma sample in another semi-micro cuvette.</li>
	<li>Mix the contents in both cuvettes by flushing the pipette thoroughly by repeatedly filling with reaction mixture, and incubate at least 3 min at room temperature.</li>
	<li>Determine the extinction (E) of the sample against fHb reagent as blank reagent. Calculate the fHb-concentration (mmol/l) of the sample: E540-E680 x 0.452.</li>
</ol>
7. Measurement of FPA
<ol>
	<li>Thaw a plasma sample from each condition obtained as described in 3.7.5 and store on ice after thawing.</li>
	<li>Use the FPA Elisa kit and follow the manufacturer&#8217;s instructions.</li>
</ol>
8. Measurement of sC5b9
<ol>
	<li>Thaw a plasma sample from each condition obtained as described in 3.7.5 and store on ice after thawing.</li>
	<li>Use the sC5b-9 ELISA kit and follow the manufacturer&#8217;s instructions.</li>
</ol>
9. Measurement of PMN
<ol>
	<li>Thaw a plasma sample from each condition obtained as described in 3.7.5 and store on ice after thawing.</li>
	<li>Use the PMN-Elastase ELISA kit and follow the manufacturer&#8217;s instructions.</li>
</ol>
10. Measurement of TNF
<ol>
	<li>Microplates must be coated one day before running the ELISA. For coating, add 100 &#181;L of capture antibody solution to all wells, seal plate and incubate overnight at 2 &#176;C-8 &#176;C.</li>
	<li>Thaw one plasma sample from each condition obtained as described in 3.7.5. Store on ice after thawing.</li>
	<li>Use the TNF ELISA kit and follow the manufacturer&#8217;s instructions.</li>
</ol>
11. Measurement of IL-6
<ol>
	<li>Microplates must be coated with capture antibodies one day prior to the experiment. For coating, add 100 &#181;L of capture antibody solution to all wells of the microplate provided with the set, seal plate and incubate overnight at 4 &#176;C</li>
	<li>Thaw a plasma sample from each condition obtained as described in 3.7.5. and store on ice after thawing.</li>
	<li>Use the IL-6 ELISA kit and follow the manufacturer&#8217;s instructions..</li>
</ol>
12. FACS analyses
<ol>
	<li>Prepare 500 mL of FACS buffer by adding 10 mL of fetal calf serum and 2 mL of EDTA solution (0.5 M) to 488 mL of 1x PBS. The FACS buffer can be stored for 4 weeks at 4&#176;C.</li>
	<li>Use 100 &#956;L of the sodium citrate blood (see 3.6.3) for each staining procedure (monocyte platelet aggregates (MPA), platelet activation (PA), leukocyte integrins (LI)).</li>
	<li>Pipette 100 &#956;L of blood from each sample into a 5 mL FACS tube. From each sample, prepare 3 tubes for antibody staining and label with MPA (monocyte platelet aggregates) panel, PA (platelet aggregates) panel and LI (leukocyte integrin) panel.</li>
	<li>Mix the rest of the 4 samples into one 5 mL FACS tube. Use this mix for unstained and fluorescence minus one (FMO) controls.</li>
	<li>Prepare 6 FACS tubes by pipetting 100 &#181;L of the mixed sample blood into each tube. Label 3 tubes as unstained and 3 tubes as FMO-CD41, FMO-CD62P and FMO-CD162.</li>
	<li>Add 100 &#181;L of 4% paraformaldehyde solution and incubate for 15 min in the dark at room temperature. 
	CAUTION: Paraformaldehyde is toxic to skin and eyes. It can cause serious pulmonary irritation when inhaled and can lead to lung damage after prolonged exposure. Furthermore, it is classified as a carcinogen and a reproductive toxin. Always wear gloves and safety glasses and work under the fume hood.</li>
	<li>Add 1 mL of wash buffer to each tube and centrifuge at 287&#160;x g for 5 min. Discard the supernatant and repeat wash step two times.</li>
	<li>For red blood cell (RBC) lysis, add 1 mL of 1x buffer RBC lysis buffer (dilute 10x RBC lysis buffer in deionized water), mix by slowly pipetting up and down and incubate for 5 min at RT in the dark.</li>
	<li>Prepare compensation beads for single stains. To 1 mL of FACS buffer add 4 drops of each positive and negative beads. Vortex thorough and add 100 &#181;L of beads solution to one 5 mL FACS tube.</li>
	<li>Prepare 4 tubes with beads and label as CD14-FITC, CD41-BV421, CD45-APC and CD62P-PE. Add 1 mL of FACS buffer to each tube and centrifuge at 287&#160;x g for 5 min. Discard supernatant and keep on ice.</li>
	<li>After RBC lysis, add 1 mL of FACS buffer to each tube and wash as described in 12.7. Discard supernatant.</li>
	<li>Prepare antibody cocktails:
	<ol>
		<li>MPA panel: Add 4 &#181;L of CD45-APC, 4 &#181;L of CD14-FITC and 4 &#181;L of CD41-BV421 to 388 &#181;L of FACS buffer.</li>
		<li>PA panel: Add 1.6 &#181;L of CD41-BV421 and 12 &#181;L of CD62P-PE to 386.4 &#181;L of FACS buffer.</li>
		<li>LI panel: Add 4 &#181;L of CD45-APC and 8 &#181;L of CD162-BV421 to 388 &#181;L of FACS buffer. Keep on ice.</li>
	</ol>
	</li>
	<li>Prepare single stains: Add 0.5 &#181;L to 499.5 &#181;L of FACS buffer each for CD14-FITC, CD41-BV421 and CD45-APC. For CD62P-PE add 0.3 &#181;L to 499.7 &#181;L of FACS buffer. Keep on ice.</li>
	<li>Prepare FMO controls: (i) MPA panel (FMO-CD41): Add 1 &#181;L CD14-FITC antibody and 1 &#181;L of CD45-APC antibody to 98 &#181;L FACS buffer. (ii) PA panel (FMO-CD62P): Add 0.4 &#181;L of CD41-BV421 to 99.6 &#181;L of FACS buffer. (iii) LI panel (FMO-CD162): Add 1 &#181;L of CD45-APC to 99 &#181;L of FACS buffer. Keep FMO controls on ice.</li>
	<li>Vortex antibody cocktails and add 100 &#181;L of each antibody cocktail as prepared in 12.12 to each of the respective labeled tubes (MPA, PA and LI panel) as described in 12.3 and mix gently by pipetting up and down. Keep on RT in the dark.</li>
	<li>Vortex single stain antibody dilutions and add 100 &#181;L of the single stain antibody dilutions as prepared in 12.13. to each of the respective labeled tubes with beads as described in 12.7 and mix gently by pipetting up and down. Keep on RT in the dark.</li>
	<li>Vortex FMO antibody cocktails and add 100 &#181;L of each FMO-1 antibody cocktail as prepared in 12.14. to each of the respective labeled tubes (FMO controls) as described in 12.5. and mix gently by pipetting up and down. Keep at RT in the dark.</li>
	<li>Incubate all tubes with antibody staining for 30 min at RT in the dark.</li>
	<li>Take the three tubes for unstained control (see 12.4) and resuspend pellet in 250 &#181;L of FACS buffer. Keep on ice.</li>
	<li>After incubation time, wash all tubes except unstained controls one time with FACS buffer as described in 12.7. Resuspend pellet in in 250 &#181;L of FACS buffer and acquire data on the flow cytometer.</li>
	<li>Use unstained cells for negative settings and compensation mouse beads for positive settings in FACS software. Further, use FMO to control the gating strategy, where FMO-CD41 is used in MPA panel, FMO-CD62P is used in PA panel and FMO-CD162 is used in LI panel.</li>
	<li>Acquire almost 0.5 x 106 - 0.25 x 106 events per tube for FACS. Save data and analyze with an analysis software (version 9.9.6).</li>
</ol>

<ol>
	<li>International Organisation for Standardisation. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=DIN+ISO+10993-4:+Biological+evaluation+of+medical+devices+-+Part+4:+Selection+of+tests+for+interactions+with+blood.">DIN ISO 10993-4: Biological evaluation of medical devices - Part 4: Selection of tests for interactions with blood.</a> International Organisation for Standardisation. , (2017).</li><li>Mayes, J. T., Schreiber, R. D., Cooper, N. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+and+application+of+an+enzyme-linked+immunosorbent+assay+for+the+quantitation+of+alternative+complement+pathway+activation+in+human+serum.">Development and application of an enzyme-linked immunosorbent assay for the quantitation of alternative complement pathway activation in human serum.</a> Journal of Clinical Investigation. 73 (1), 160-170 (1984).</li><li>Maiolini, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+sandwich+method+of+enzyme-immunoassay.+II.+Quantification+of+rheumatoid+factor.">A sandwich method of enzyme-immunoassay. II. Quantification of rheumatoid factor.</a> Journal of Immunological Methods. 20, 25-34 (1978).</li><li>Shapiro, H. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Flow+Cytometry:+The+Glass+Is+Half+Full.">Flow Cytometry: The Glass Is Half Full.</a> Methods in Molecular Biology. 1678, 1-10 (2018).</li><li>Betke, U., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Impact+of+Slurry+Composition+on+Properties+of+Cellular+Alumina:+A+Computed+Tomographic+Study.">Impact of Slurry Composition on Properties of Cellular Alumina: A Computed Tomographic Study.</a> Advanced Engineering Materials. 19 (10), (2017).</li><li>Chandler, A. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vitro+thrombotic+coagulation+of+the+blood;+a+method+for+producing+a+thrombus.">In vitro thrombotic coagulation of the blood; a method for producing a thrombus.</a> Laboratory Investigation. 7 (2), 110-114 (1958).</li><li>Fink, H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+in+vitro+study+of+blood+compatibility+of+vascular+grafts+made+of+bacterial+cellulose+in+comparison+with+conventionally-used+graft+materials.">An in vitro study of blood compatibility of vascular grafts made of bacterial cellulose in comparison with conventionally-used graft materials.</a> Journal of Biomedical Materials Research Part A. 97 (1), 52-58 (2011).</li><li>Lenz-Habijan, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+the+Thrombogenicity+of+a+Bare+and+Antithrombogenic+Coated+Flow+Diverter+in+an+In+Vitro+Flow+Model.">Comparison of the Thrombogenicity of a Bare and Antithrombogenic Coated Flow Diverter in an In Vitro Flow Model.</a> Cardiovascular and Interventional Radiology. 43 (1), 140-146 (2020).</li><li>Olsen, A. L., Long, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+catheter+thrombogenicity+in+a+modified+chandler+loop+model+using+goat+blood.">Comparison of catheter thrombogenicity in a modified chandler loop model using goat blood.</a> Journal of Biomedical Materials Research Part A. 106 (12), 3143-3151 (2018).</li><li>Touma, H., Sahin, I., Gaamangwe, T., Gorbet, M. B., Peterson, S. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Numerical+investigation+of+fluid+flow+in+a+chandler+loop.">Numerical investigation of fluid flow in a chandler loop.</a> Journal of Biomechanical Engineering. 136 (7), (2014).</li><li>Slee, J. B., Alferiev, I. S., Levy, R. J., Stachelek, S. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+use+of+the+ex+vivo+Chandler+Loop+Apparatus+to+assess+the+biocompatibility+of+modified+polymeric+blood+conduits.">The use of the ex vivo Chandler Loop Apparatus to assess the biocompatibility of modified polymeric blood conduits.</a> Journal of Visualized Experiments. (90), e51871 (2014).</li><li>Feyerabend, F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Blood+compatibility+of+magnesium+and+its+alloys.">Blood compatibility of magnesium and its alloys.</a> Acta Biomaterialia. 25, 384-394 (2015).</li><li>Lukas, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+Immobilized+Antithrombin+III+on+the+Thromboresistance+of+Polycarbonate+Urethane.">Effect of Immobilized Antithrombin III on the Thromboresistance of Polycarbonate Urethane.</a> Materials. 10 (4), 355 (2017).</li><li>Paul, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Aptamers+influence+the+hemostatic+system+by+activating+the+intrinsic+coagulation+pathway+in+an+in+vitro+Chandler-Loop+model.">Aptamers influence the hemostatic system by activating the intrinsic coagulation pathway in an in vitro Chandler-Loop model.</a> Clinical and Applied Thrombosis/Hemostasis. 16 (2), 161-169 (2010).</li><li>Link, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hemocompatibility+Testing+of+Blood-Contacting+Implants+in+a+Flow+Loop+Model+Mimicking+Human+Blood+Flow.">Hemocompatibility Testing of Blood-Contacting Implants in a Flow Loop Model Mimicking Human Blood Flow.</a> Journal of Visualized Experiments. (157), e60610 (2020).</li><li>van Oeveren, W., Tielliu, I. F., de Hart, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+modified+chandler,+roller+pump,+and+ball+valve+circulation+models+for+in+vitro+testing+in+high+blood+flow+conditions:+application+in+thrombogenicity+testing+of+different+materials+for+vascular+applications.">Comparison of modified chandler, roller pump, and ball valve circulation models for in vitro testing in high blood flow conditions: application in thrombogenicity testing of different materials for vascular applications.</a> International Journal of Biomaterials. 2012, 673163 (2012).</li><li>Maa, Y. F., Hsu, C. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Protein+denaturation+by+combined+effect+of+shear+and+air-liquid+interface.">Protein denaturation by combined effect of shear and air-liquid interface.</a> Biotechnology and Bioengineering. 54 (6), 503-512 (1997).</li><li>Mutch, N. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+use+of+the+Chandler+loop+to+examine+the+interaction+potential+of+NXY-059+on+the+thrombolytic+properties+of+rtPA+on+human+thrombi+in+vitro.">The use of the Chandler loop to examine the interaction potential of NXY-059 on the thrombolytic properties of rtPA on human thrombi in vitro.</a> British Journal of Pharmacology. 153 (1), 124-131 (2008).</li><li>Fletcher, E. A. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Extracorporeal+human+whole+blood+in+motion,+as+a+tool+to+predict+first-infusion+reactions+and+mechanism-of-action+of+immunotherapeutics.">Extracorporeal human whole blood in motion, as a tool to predict first-infusion reactions and mechanism-of-action of immunotherapeutics.</a> International Immunopharmacology. 54, 1-11 (2018).</li><li>Krajewski, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hemocompatibility+evaluation+of+different+silver+nanoparticle+concentrations+employing+a+modified+Chandler-loop+in+vitro+assay+on+human+blood.">Hemocompatibility evaluation of different silver nanoparticle concentrations employing a modified Chandler-loop in vitro assay on human blood.</a> Acta Biomaterialia. 9 (7), 7460-7468 (2013).</li><li>Larm, O., Larsson, R., Olsson, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+non-thrombogenic+surface+prepared+by+selective+covalent+binding+of+heparin+via+a+modified+reducing+terminal+residue.">A new non-thrombogenic surface prepared by selective covalent binding of heparin via a modified reducing terminal residue.</a> Biomaterials, Medical Devices, and Artificial Organs. 11 (2-3), 161-173 (1983).</li><li>Gong, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tubing+loops+as+a+model+for+cardiopulmonary+bypass+circuits:+both+the+biomaterial+and+the+blood-gas+phase+interfaces+induce+complement+activation+in+an+in+vitro+model.">Tubing loops as a model for cardiopulmonary bypass circuits: both the biomaterial and the blood-gas phase interfaces induce complement activation in an in vitro model.</a> Journal of Clinical Immunology. 16 (4), 222-229 (1996).</li><li>Tevaearai, H. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Trillium+coating+of+cardiopulmonary+bypass+circuits+improves+biocompatibility.">Trillium coating of cardiopulmonary bypass circuits improves biocompatibility.</a> The International Journal of Artificial Organs. 22 (9), 629-634 (1999).</li><li>Ma, Y. Q., Plow, E. F., Geng, J. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=P-selectin+binding+to+P-selectin+glycoprotein+ligand-1+induces+an+intermediate+state+of+alphaMbeta2+activation+and+acts+cooperatively+with+extracellular+stimuli+to+support+maximal+adhesion+of+human+neutrophils.">P-selectin binding to P-selectin glycoprotein ligand-1 induces an intermediate state of alphaMbeta2 activation and acts cooperatively with extracellular stimuli to support maximal adhesion of human neutrophils.</a> Blood. 104 (8), 2549-2556 (2004).</li><li>Bandyk, D. F., Galbraith, T. A., Haasler, G. B., Almassi, G. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Blood+flow+velocity+of+internal+mammary+artery+and+saphenous+vein+grafts+to+the+coronary+arteries.">Blood flow velocity of internal mammary artery and saphenous vein grafts to the coronary arteries.</a> Journal of Surgical Research. 44 (4), 342-351 (1988).</li><li>Gardner, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+examination+of+the+fluid+mechanics+and+thrombus+formation+time+parameters+in+a+Chandler+rotating+loop+system.">An examination of the fluid mechanics and thrombus formation time parameters in a Chandler rotating loop system.</a> Journal of Laboratory and Clinical Medicine. 84 (4), 494-508 (1974).</li><li>Gaamangwe, T., Peterson, S. D., Gorbet, M. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigating+the+Effect+of+Blood+Sample+Volume+in+the+Chandler+Loop+Model:+Theoretical+and+Experimental+Analysis.">Investigating the Effect of Blood Sample Volume in the Chandler Loop Model: Theoretical and Experimental Analysis.</a> Cardiovascular Engineering and Technology. 5 (2), 133-144 (2014).</li><li>B&#246;swirth, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Technische Str&#246;mungslehre. 8 edn. , (2010).</li><li>Cartwright, I. J., Pockley, A. G., Galloway, J. H., Greaves, M., Preston, F. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effects+of+dietary+omega-3+polyunsaturated+fatty+acids+on+erythrocyte+membrane+phospholipids,+erythrocyte+deformability+and+blood+viscosity+in+healthy+volunteers.">The effects of dietary omega-3 polyunsaturated fatty acids on erythrocyte membrane phospholipids, erythrocyte deformability and blood viscosity in healthy volunteers.</a> Atherosclerosis. 55 (3), 267-281 (1985).</li><li>Wong, K. K. L., Wu, J., Liu, G., Huang, W., Ghista, D. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coronary+arteries+hemodynamics:+effect+of+arterial+geometry+on+hemodynamic+parameters+causing+atherosclerosis.">Coronary arteries hemodynamics: effect of arterial geometry on hemodynamic parameters causing atherosclerosis.</a> Medical &amp; biological engineering &amp; computing. 58, 1831-1843 (2020).</li><li>Kania, R. E., Herman, P., Ar, A., Tran Ba Huy, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Technical+pitfalls+in+middle+ear+gas+studies:+errors+introduced+by+the+gas+permeability+of+tubing+and+additional+dead+space.">Technical pitfalls in middle ear gas studies: errors introduced by the gas permeability of tubing and additional dead space.</a> Acta Oto-Laryngologica. 125 (5), 529-533 (2005).</li><li>Foley, M. E., McNicol, G. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+in-vitro+study+of+acidosis,+platelet+function,+and+perinatal+cerebral+intraventricular+haemorrhage.">An in-vitro study of acidosis, platelet function, and perinatal cerebral intraventricular haemorrhage.</a> The Lancet. 1 (8024), 1230-1232 (1977).</li><li>Engstrom, M., Schott, U., Romner, B., Reinstrup, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acidosis+impairs+the+coagulation:+A+thromboelastographic+study.">Acidosis impairs the coagulation: A thromboelastographic study.</a> The Journal of Trauma. 61 (3), 624-628 (2006).</li><li>Dirkmann, D., Hanke, A. A., Gorlinger, K., Peters, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hypothermia+and+acidosis+synergistically+impair+coagulation+in+human+whole+blood.">Hypothermia and acidosis synergistically impair coagulation in human whole blood.</a> Anesthesia &amp; Analgesia. 106 (6), 1627-1632 (2008).</li><li>Ritz-Timme, S., Eckelt, N., Schmidtke, E., Thomsen, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Genesis+and+diagnostic+value+of+leukocyte+and+platelet+accumulations+around+"air+bubbles"+in+blood+after+venous+air+embolism.">Genesis and diagnostic value of leukocyte and platelet accumulations around "air bubbles" in blood after venous air embolism.</a> International Journal of Legal Medicine. 111 (1), 22-26 (1998).</li><li>Thorsen, T., Klausen, H., Lie, R. T., Holmsen, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bubble-induced+aggregation+of+platelets:+effects+of+gas+species,+proteins,+and+decompression.">Bubble-induced aggregation of platelets: effects of gas species, proteins, and decompression.</a> Undersea &amp; Hyperbaric Medicine : Journal of the Undersea and Hyperbaric Medical Society, Inc. 20 (2), 101-119 (1993).</li><li>Streller, U., Sperling, C., Hubner, J., Hanke, R., Werner, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+evaluation+of+novel+blood+incubation+systems+for+in+vitro+hemocompatibility+assessment+of+planar+solid+surfaces.">Design and evaluation of novel blood incubation systems for in vitro hemocompatibility assessment of planar solid surfaces.</a> Journal of Biomedical Materials Research Part B. 66 (1), 379-390 (2003).</li><li>Hesh, C. A., Qiu, Y., Lam, W. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vascularized+microfluidics+and+the+blood-endothelium+interface.">Vascularized microfluidics and the blood-endothelium interface.</a> Micromachines. 11 (1), 18 (2019).</li><li>Nordling, S., Nilsson, B., Magnusson, P. U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel+in+vitro+model+for+studying+the+interactions+between+human+whole+blood+and+endothelium.">A novel in vitro model for studying the interactions between human whole blood and endothelium.</a> Journal of Visualized Experiments. (93), e52112 (2014).</li></ol>

The funder [ebo kunze industriedesign, Im Dentel 17, 72639 Neuffen, Germany] provided a financial support in the form of consumables and publication fees to the author of this manuscript [Max Wacker]. The funders did not have any additional role in the study design, data collection and analysis, decision to publish, or preparation of the manuscript.

This study has shown that the presented in vitro hemodynamic loop model offers a reliable method for testing the in vitro blood compatibility of medical devices in accordance to the ISO 10993-4 standard.
Critical steps in the protocol include the drawing of blood and filling the tubes with blood, where excessive vacuum or agitation should be avoided to prevent the blood components from activation by the handling procedure. Furthermore, it is very important to immediately freeze the plasma samples and keep them on ice after thawing, as the complement and coagulation system activation can be tampered by keeping the samples on room temperature for a longer time.
Since this model has both merits and demerits when compared to other in vitro models, several factors have to be taken into account while designing the experiments.
First, the loops can be varied in length and diameter to fit various experimental setups. In case the setup includes contrasting tubes of varying inner diameters, it should be kept in mind that the differences in diameter will result in different shear forces, thereby affecting the coagulation and complement cascade7. Second, the rotation speed was set to 30 rpm in this experiment. This will result in a blood flow of approximately 25 cm/s, which is comparable to the blood flow velocity in human coronary artery bypass grafts25. The strain rate, generated by the rotation of the loops, is the major parameter that will initiate biochemical cascades of blood components, including cells and cell-free proteins. But as blood is a non-Newtonian fluid, the strain rate will also be influenced by the tube curvature, respectively the length of the tubes that are closed to loops10. Whenever the rotation speed or loop size is changed, it is important to consider that the correlation between strain rate and rotation speed is not linear. The correlation between the rotation speed and strain rate is not sufficiently examined until today and further studies are required to investigate these particular parameters10,26,27. However, based on a model for laminar boundary layer, the given tube diameter of 5 mm and the rotation speed of 25 cm/s, a rough estimation of the wall shear stress (WSS) would indicate values between 2.20-22.00 pascal for a distance of 1,00-0,01 mm to the wall of the tube when the blood density is estimated to be 1060 kg*m-3 and the kinetical viscosity is set to 0.0025 pascal*s28,29. Interestingly, also a more detailed computational analysis of flow dynamics in the curvature of human coronary arteries showed WSS values ranging from 11.33 to 16.77 pascal at roughly comparable parameters for the velocity, density and viscosity of the blood30.
Beside this limitation, the presented loop model is a pressure less system, that does not mimic the intravascular blood pressure ratios of the human vascular system.
Next important limitation is that the blood is in contact with air inside the loops, which brings additional interferences. Such a blood-air contact is impacted by two parameters, which includes the gas permeability of the tubes and the retainment of air inside the loops while filling them with blood. Every tube material possesses a certain gas permeability that can lead to significant changes in gas concentrations inside the tubes. While some authors state that the resultant effect of the gas permeability on activation of blood components remains unclear31, it is known that the function of the blood coagulators is highly sensitive to a pH-shift, that may be caused by CO2 diffusion32,33,34. Here, we have tested the biocompatibility of blood perfusion tubes under indoor air conditions, comparable to clinical scenarios of extracorporeal blood perfusion. For future improvements of the presented model, incubation of the whole model in a CO2 incubator and performing blood pH validation before and after incubation might be useful to further standardize this model.
Also, the blood-air interface inside the loops can lead to activation of plasma proteins and cell fractions of the blood35,36. The roller pump driven devices without air inside the tubes may avoid the issue of blood-air interface, but they certainly induce damage to blood cells with significant elevated levels of hemoglobin compared to the here presented loop model, and the hemoglobin in plasma can interfere with the sensitivity of tested analytes in ELISA16. In this study we have shown that the hemolytic effect of the loop model itself remains minimal while using biocompatible materials such as heparin coated PVC tubes. Thus, the model is, on the one hand, not causing excessive cell damage compared to pump driven models, but on the other hand inducing plasma proteins due to blood air contact. Of note, van Oeveren et al. developed a ball-valve based loop model avoiding air inside the loops16. This promising alternative to the here presented loop model may overcome the problem of the blood-air interface, however, compared to the model presented here, platelet adhesion is still higher for the ball-valve based loop model.
With regard to the static control, it is of note that glass itself has been shown to be a potent activator of the coagulatory system37. However, in the presented setup, incubation in a glass beaker (static control) did not lead to excessive host cell activation or activation of the coagulatory system compared to the baseline levels directly after drawing the blood. In conclusion, it might be helpful to use for example polypropylene tubes, if the static control shows high levels of activation.
Regardless of whether it is a loop based or a pump-driven model, these in vitro models completely lack the authentic biological interactions that are mainly contributed by an intact endothelium, which is an ideal blood contacting surface. The rationale behind this issue is more evident when a medical device like a stent is being tested, which might impart different outcomes, in terms of activation and plasma proteins, during its interaction with blood components in the presence of endothelium. This declares to be a major drawback of all discussed in vitro systems mimicking the circulatory system. Hence, to overcome this issue, new microfluidic systems that are completely covered with endothelium are gaining immense interest, but nevertheless in comparison to the loop model presented here, they are still limited to accommodate smaller blood volumes and minimal flow rates38,39
Thus, we conclude that the Chandler Loop model remains to be a robust model for conducting standardized tests on the blood biocompatibility of vascular medical devices in the field of cardiovascular research.

Hemocompatibility testing of medical devices is a crucial step in the development of new devices such as vascular stents or perfusion tubes for extracorporeal membrane oxygenation. Until today, animal models are considered as standard tools to finalize the procedure for testing the medical devices prior to its implementation in humans. Henceforth, it is necessary to find alternative in vitro models that further aid in minimizing investigations on animals. In this study, we, therefore, have explored a miniature in vitro hemodynamic loop model. The goal of this presented method is to test the in vitro blood compatibility of medical devices in accordance to the ISO 10993-4 standard.
The ISO 10993-4 standard describes standardized sets of clinical parameters to be investigated on blood specimen1. Briefly, these are thrombosis (platelet aggregation and count), coagulation (fibrinopeptide A, FPA), hematological analysis (whole blood cell count), hemolysis index (free plasma hemoglobin) and the complement system (terminal complement complex, sC5b9). However, additional markers, such as neutrophil polymorphonuclear elastase (PMN), interleukin 6 (IL-6) and tumor necrosis factor - alpha (TNF) reflecting the activation status of leukocytes can also be accounted for measurements. To determine and to quantify the circulating cell free proteins that are present in blood plasma, sandwich enzymatic linked immunosorbent assay (ELISA) represents a conventional and most reliable method2,3. Likewise, the phenotype and activation status of the host cells (e.g., leukocytes) can be quantified by detecting the cell surface expression of molecules by flow cytometry (FACS) that provides single cell suspension based readouts, where fluorescent labeled specific antibodies bind to the targeted cell surface molecules4. Scanning electron microscopy (SEM) is also recommended to determine thrombus formation on the tested material by the ISO 10993-4 standard1. This method can be complemented with X-ray microtomography (&#956;CT), to perform structural analysis of the thrombus e.g., its thickness, size and localization in a 3D rendered image5.
The rationale behind using this in vitro hemodynamic model is to screen for the best performing and compatible medical devices by understanding the basic physiological dynamics of blood components such as platelets, that are involved in the primary hemostasis or leukocytes and their interaction with different types of vascular devices. Such in vitro systems are highly demanded as they reduce the need for animal studies.
The here presented loop model fulfills these demands. This model was first described by A.B. Chandler in 1958 for the production of blood thrombi and is, therefore, also called Chandler Loop model6. Until now, this model has been used in a series of experiments and modifications to investigate the blood biocompatibility of medical devices7,8,9,10,11,12,13,14. It consists of polymer tubes, which are partly filled with blood and shaped into re-closable loops. These loops rotate in a temperature-controlled water bath to simulate vascular flow conditions with its hemorheological effects. Alternative methods such as pump driven models or models that use mechanical ball valves inside the loops to induce a blood flow inside the polymer tubes have already been described15,16. However, the overall advantage of the here presented method is that the mechanical force applied to the blood cells and proteins is low, avoiding hemolysis, and there is no contact between blood and connectors, that could possibly lead to flow turbulences and activation of blood components. The main activating factors inside the loop are the test material itself and the air that is trapped inside. This helps to minimize sources of measuring error and to deliver a high reproducibility, even if the blood-air interface can lead to protein denaturation17. It is also possible to investigate varieties of tubing materials and stent diameters without length or size restrictions thereby allowing the use of tubes of different length and inner diameter. Moreover, host hemocompatibilities on inaccurate loop closure and exposure to the uncoated tube surface are also possible to investigate. Other similar medical applications of this in vitro hemodynamic loop model is that it could also be used to study the interactions between immunotherapeutics (drugs) and blood components during either preclinical development or individual drug safety screening prior to first-in-man phase I clinical trial, or for the generation of thrombus material that can be used in further experiments18,19,20.
This study describes a detailed protocol for testing the hemocompatibilities of perfusion tubes and/or stents. Here, the comparison between uncoated and coated PVC tubes (hepPVC: heparin coating, polyPVC: coating with an bioactive polymer). Lowered activation of platelets, but a higher activation of the coagulation system (FPA) were found for both coated tubes in comparison to the uncoated tubes. The hepPVC tubes used here are modified with covalently bound heparin to make them thromboresistant21 and have already been employed in a loop model to optimize and characterize different parameters22. The polyPVC tubes used in this study are commercially available tubes used in clinical settings of extracorporeal blood perfusion and are coated with a heparin polymer to reduce their thrombogenicity23. Sometimes, in clinical applications even uncoated PVC tubes are used. Therefore, we included latex tubes as a positive control group that showed excessive activation of platelets, coagulation system, and soluble factors like IL-6, TNF and PMN elastase. Thrombus formation was noticed when inaccurate loop closure was simulated. This led to the activation of coagulation and complement system as well as leukocytes and platelets compared to the baseline conditions. Furthermore, blood contact to the here used stent material (bare metal nitinol stent, covered with carbon-impregnated expanded polytetrafluoroethylene) led to higher platelet and leukocyte activation in terms of PMN elastase. Overall, the presented model did not induce hemolysis in any of the tested vascular devices as they were comparable to the baseline or static conditions, except for the latex tubes, where red blood cell (RBC) hemolysis was obvious. Moreover, these perfusion tubes can be examined either by imaging or by histology. Though histological evaluations might be feasible, we mainly focused on ELISA and flow cytometry to perform these experiments and thereby enabling the feasibilities of conducting experiments based on the here presented model for many laboratories. Thus, this method represents a feasible method to test the blood biocompatibility of vascular medical devices in accordance with the recommendations of the ISO 10993-4 standard. Furthermore, this method can be used whenever an interaction between blood and materials should be tested under flow conditions, mimicking the in vivo conditions.

<table>
	<tbody>
		<tr>
			<td>5 ml tube, K3 EDTA</td>
			<td>Sarstedt</td>
			<td>32332</td>
			<td></td>
		</tr>
		<tr>
			<td>Anti-Mouse Ig, &#954;/Negative Control Compensation Particles Set</td>
			<td>Becton Dickinson BioSciences</td>
			<td>552843</td>
			<td></td>
		</tr>
		<tr>
			<td>APC anti-human CD45 Antibody</td>
			<td>BioLegend</td>
			<td>368512</td>
			<td></td>
		</tr>
		<tr>
			<td>BD LSR Fortessa II cell analyzer</td>
			<td>Becton Dickinson</td>
			<td>647465</td>
			<td></td>
		</tr>
		<tr>
			<td>BD Vacutainer Citrate Tubes</td>
			<td>Becton Dickinson</td>
			<td>369714</td>
			<td></td>
		</tr>
		<tr>
			<td>BD Vacutainer one-use holder</td>
			<td>Becton Dickinson</td>
			<td>364815</td>
			<td></td>
		</tr>
		<tr>
			<td>BD Vacutainer Safety-Lok butterfly canula 21 G</td>
			<td>Becton Dickinson</td>
			<td>367282</td>
			<td></td>
		</tr>
		<tr>
			<td>Beaker glass ROTILABO short 10 ml</td>
			<td>Carl Roth GmbH + Co. KG</td>
			<td>X686.1</td>
			<td></td>
		</tr>
		<tr>
			<td>Beaker glass ROTILABO short 50 ml</td>
			<td>Carl Roth GmbH + Co. KG</td>
			<td>X688.1</td>
			<td></td>
		</tr>
		<tr>
			<td>Brilliant Violet 421 anti-human CD162 Antibody</td>
			<td>BioLegend</td>
			<td>328808</td>
			<td></td>
		</tr>
		<tr>
			<td>Brilliant Violet 421 anti-human CD41 Antibody</td>
			<td>BioLegend</td>
			<td>303730</td>
			<td></td>
		</tr>
		<tr>
			<td>Centrifuge ROTINA 420 | 420 R</td>
			<td>Hettich Zentrifugen</td>
			<td>4701 | 4706</td>
			<td></td>
		</tr>
		<tr>
			<td>Centrifuge tubes, 50 ml</td>
			<td>Greiner Bio-One GmbH</td>
			<td>227261</td>
			<td></td>
		</tr>
		<tr>
			<td>CHC Super modified, 5mm PVC tubing</td>
			<td>Corline Sweden</td>
			<td>1807-148</td>
			<td>Referred to as hepPVC tube</td>
		</tr>
		<tr>
			<td>Circular Precision Cutter</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 007-20</td>
			<td></td>
		</tr>
		<tr>
			<td>Closing Unit (complete with tension bands)</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 008-20</td>
			<td></td>
		</tr>
		<tr>
			<td>Electric tape Scotch Super 33+</td>
			<td>VWR</td>
			<td>MMMA331933</td>
			<td></td>
		</tr>
		<tr>
			<td>ELISA MAX Deluxe Set Human IL-6</td>
			<td>BioLegend</td>
			<td>430504</td>
			<td></td>
		</tr>
		<tr>
			<td>ELISA MAX Deluxe Set Human TNF-a</td>
			<td>BioLegend</td>
			<td>430204</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. box, 0,1 &#8211; 2,5 &#181;L, gray</td>
			<td>Eppendorf AG</td>
			<td>3123000012</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. box, 0,5 &#8211; 10 &#181;L, gray</td>
			<td>Eppendorf AG</td>
			<td>3123000020</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. box, 10 &#8211; 100 &#181;L, yellow</td>
			<td>Eppendorf AG</td>
			<td>3123000047</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. box, 100 &#8211; 1,000 &#181;L, blue</td>
			<td>Eppendorf AG</td>
			<td>3123000063</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. box, 20 &#8211; 200 &#181;L, yellow</td>
			<td>Eppendorf AG</td>
			<td>3123000055</td>
			<td></td>
		</tr>
		<tr>
			<td>Eppendorf Pipette Research plus, single channel, inkl. epT.I.P.S. sample bag, 0,5 &#8211; 5 mL, violet</td>
			<td>Eppendorf AG</td>
			<td>3123000071</td>
			<td></td>
		</tr>
		<tr>
			<td>Ethylenediaminetetraacetic acid solution</td>
			<td>Sigma-Aldrich</td>
			<td>03690-100ML</td>
			<td></td>
		</tr>
		<tr>
			<td>FACS tubes polystyrene 5.0 ml round bottom</td>
			<td>Corning BV</td>
			<td>352052</td>
			<td></td>
		</tr>
		<tr>
			<td>Fetal bovine serum Gold Plus</td>
			<td>Bio-Sell</td>
			<td>FBS.GP.0500</td>
			<td></td>
		</tr>
		<tr>
			<td>FITC anti-human CD14 Antibody</td>
			<td>BioLegend</td>
			<td>367116</td>
			<td></td>
		</tr>
		<tr>
			<td>Fluency plus stent 13.5 x 60 mm</td>
			<td>Angiomed GmbH &#38; Co</td>
			<td>FVM14060</td>
			<td></td>
		</tr>
		<tr>
			<td>Free Hemoglobin fHb Reagent</td>
			<td>Bioanalytics GmbH</td>
			<td>004001-0250</td>
			<td></td>
		</tr>
		<tr>
			<td>Gibco PBS Tablets</td>
			<td>Thermo Fisher Scientific</td>
			<td>18912014</td>
			<td></td>
		</tr>
		<tr>
			<td>Gloves Vasco Nitril white L</td>
			<td>B. Braun Deutschland GmbH &#38; Co.KG</td>
			<td>9208437</td>
			<td></td>
		</tr>
		<tr>
			<td>Gloves Vasco Nitril white M</td>
			<td>B. Braun Deutschland GmbH &#38; Co.KG</td>
			<td>9208429</td>
			<td></td>
		</tr>
		<tr>
			<td>Glutaraldehyde 25% aequous solution</td>
			<td>Sigma Aldrich</td>
			<td>G6257-100ML</td>
			<td></td>
		</tr>
		<tr>
			<td>Heparin, 25.000 IE in 5 ml</td>
			<td>Rotexmedica, Trittau, Germany</td>
			<td>PZN 3862340</td>
			<td></td>
		</tr>
		<tr>
			<td>Human Fibrinopeptide A (FPA) ELISA Kit</td>
			<td>H&#246;lzel Diagnostika</td>
			<td>abx253234</td>
			<td></td>
		</tr>
		<tr>
			<td>Kodan tincture forte colourless</td>
			<td>Sch&#252;lke &#38; Mayr GmbH</td>
			<td>104012</td>
			<td></td>
		</tr>
		<tr>
			<td>Latex tube, ID 5 mm</td>
			<td>Laborhandel24 GmbH</td>
			<td>305 0507</td>
			<td></td>
		</tr>
		<tr>
			<td>Loop Stand</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 009-20</td>
			<td></td>
		</tr>
		<tr>
			<td>Medimex venous tourniquet classic</td>
			<td>ROESER Medical GmbH</td>
			<td>310005</td>
			<td></td>
		</tr>
		<tr>
			<td>Microplate reader Infinite 200 Pro M Plex</td>
			<td>Tecan</td>
			<td>TEC006418I</td>
			<td></td>
		</tr>
		<tr>
			<td>Microplate shaker PMS-1000i</td>
			<td>VWR</td>
			<td>444-0041</td>
			<td></td>
		</tr>
		<tr>
			<td>Nalgene Metric non-phthalate PVC tubing, ID 5 mm</td>
			<td>VWR</td>
			<td>NALG8703-0508</td>
			<td>Referred to as PVC tube</td>
		</tr>
		<tr>
			<td>NexTemp (Standard) Single-Use Clinical Thermometer</td>
			<td>Medical Indicators</td>
			<td>2112-20</td>
			<td></td>
		</tr>
		<tr>
			<td>Nunc MaxiSorp ELISA Plates, uncoated</td>
			<td>BioLegend</td>
			<td>423501</td>
			<td></td>
		</tr>
		<tr>
			<td>Osmium tetroxide solution</td>
			<td>Fisher Scientific</td>
			<td>10256970</td>
			<td></td>
		</tr>
		<tr>
			<td>Paraformaldehyde Solution, 4% in PBS</td>
			<td>Thermo Fisher Scientific</td>
			<td>AAJ19943K2</td>
			<td></td>
		</tr>
		<tr>
			<td>PE anti-human CD16Antibody</td>
			<td>BioLegend</td>
			<td>302008</td>
			<td></td>
		</tr>
		<tr>
			<td>PE anti-human CD62P (P-Selectin) Antibody</td>
			<td>BioLegend</td>
			<td>304906</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipette controller, pipetus</td>
			<td>VWR</td>
			<td>612-1874</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipette tips epT.I.P.S. 0.2 - 5 ml</td>
			<td>OMNILAB-LABORZENTRUM GmbH &#38; Co. KG</td>
			<td>5186480</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipette tips epT.I.P.S. standard 0,1 - 10&#181;l</td>
			<td>Th. Geyer GmbH &#38; Co. KG</td>
			<td>9409410</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipette tips epT.I.P.S. standard 2 - 200&#181;l</td>
			<td>Th. Geyer GmbH &#38; Co. KG</td>
			<td>0030 000.870</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipette tips epT.I.P.S. standard 50 - 1000&#181;l blue</td>
			<td>Th. Geyer GmbH &#38; Co. KG</td>
			<td>0030 000.919</td>
			<td></td>
		</tr>
		<tr>
			<td>PMN (Neutrophil) Elastase Human ELISA Kit</td>
			<td>Fisher Scientific</td>
			<td>BMS269</td>
			<td></td>
		</tr>
		<tr>
			<td>Probe stand ROTILABO combi</td>
			<td>CARL ROTH</td>
			<td>K082.1</td>
			<td></td>
		</tr>
		<tr>
			<td>Rack for rotation unit (12 slots 3/8 &#39;&#39; with variable slot width)</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 011-20</td>
			<td></td>
		</tr>
		<tr>
			<td>RBC Lysis Buffer (10X)</td>
			<td>BioLegend</td>
			<td>420301</td>
			<td></td>
		</tr>
		<tr>
			<td>Reagent reservoirs</td>
			<td>VWR</td>
			<td>613-1184</td>
			<td></td>
		</tr>
		<tr>
			<td>Rotation Unit</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 010-20</td>
			<td></td>
		</tr>
		<tr>
			<td>Safe-Lock micro test tubes 0.5 ml</td>
			<td>OMNILAB-LABORZENTRUM GmbH &#38; Co. KG</td>
			<td>5409320</td>
			<td></td>
		</tr>
		<tr>
			<td>Safe-Lock micro test tubes 1.5 ml</td>
			<td>OMNILAB-LABORZENTRUM GmbH &#38; Co. KG</td>
			<td>5409331</td>
			<td></td>
		</tr>
		<tr>
			<td>sc5b9 Human ELISA KIT</td>
			<td>TECOmedicalGroup</td>
			<td>A029</td>
			<td></td>
		</tr>
		<tr>
			<td>Scalpel no 10</td>
			<td>Fisher Scientific</td>
			<td>NC9999403</td>
			<td></td>
		</tr>
		<tr>
			<td>Scanning electron microscope XL30 ESEM-FEG</td>
			<td>Philips</td>
			<td>n.a.</td>
			<td></td>
		</tr>
		<tr>
			<td>Screw top bottle ROTILABO Clear glass, 1000 ml, GL 45</td>
			<td>Carl Roth GmbH + Co. KG</td>
			<td>X715.1</td>
			<td></td>
		</tr>
		<tr>
			<td>Screw top bottle ROTILABO Clear glass, 500 ml, GL 45</td>
			<td>Carl Roth GmbH + Co. KG</td>
			<td>X714.1</td>
			<td></td>
		</tr>
		<tr>
			<td>Semi-micro cuvette 1.6 ml</td>
			<td>Sarstedt</td>
			<td>67.746</td>
			<td></td>
		</tr>
		<tr>
			<td>Serological pipette 10.0 ml</td>
			<td>Corning BV</td>
			<td>4488</td>
			<td></td>
		</tr>
		<tr>
			<td>Serological pipette, 25.0 ml</td>
			<td>Corning BV</td>
			<td>4489</td>
			<td></td>
		</tr>
		<tr>
			<td>Serological pipette, 5.0 ml</td>
			<td>Corning BV</td>
			<td>4487</td>
			<td></td>
		</tr>
		<tr>
			<td>Silicon tube, inner diameter 8 mm, outer diameter 12 mm</td>
			<td>VWR</td>
			<td>BURK8803-0812</td>
			<td></td>
		</tr>
		<tr>
			<td>Sprout mini centrifuge</td>
			<td>Biozym</td>
			<td>552034</td>
			<td></td>
		</tr>
		<tr>
			<td>Stop Solution for TMB Substrate</td>
			<td>BioLegend</td>
			<td>77316</td>
			<td></td>
		</tr>
		<tr>
			<td>Swabs, sterile</td>
			<td>Fuhrmann GmbH</td>
			<td>32055</td>
			<td></td>
		</tr>
		<tr>
			<td>Syringe, 10 ml</td>
			<td>Becton Dickinson</td>
			<td>300296</td>
			<td></td>
		</tr>
		<tr>
			<td>Temperature controlled water basin</td>
			<td>ebo kunze industriedesign, Neuffen, Germany</td>
			<td>CLS 020-20</td>
			<td></td>
		</tr>
		<tr>
			<td>tert-Butanol, 99.5%, extra pure, ACROS Organics</td>
			<td>Fisher Scientific</td>
			<td>10000730</td>
			<td></td>
		</tr>
		<tr>
			<td>TMB Substrate Set</td>
			<td>BioLegend</td>
			<td>421101</td>
			<td></td>
		</tr>
		<tr>
			<td>Trillium PVC tube, 5 mm ID</td>
			<td>Medtronic</td>
			<td>161100107100103</td>
			<td>Referred to as polyPVC tube</td>
		</tr>
		<tr>
			<td>Tween 20</td>
			<td>AppliChem</td>
			<td>A4974,0250</td>
			<td></td>
		</tr>
		<tr>
			<td>UV-Vis Spektrometer Lambda 2</td>
			<td>Perkin Elmer</td>
			<td>33539</td>
			<td></td>
		</tr>
		<tr>
			<td>Vornado Mini Vortexer</td>
			<td>Biozym</td>
			<td>55BV101-B-E</td>
			<td></td>
		</tr>
		<tr>
			<td>XN-3000 workstation blood analyzer</td>
			<td>Sysmex Europe</td>
			<td>n.a.</td>
			<td></td>
		</tr>
		<tr>
			<td>&#956;-CT Phoenix Nanotom S</td>
			<td>GE Sensing &#38; Inspection, Wunstorf, Germany</td>
			<td>n.a.</td>
			<td></td>
		</tr>
	</tbody>
</table>

an in vitro hemodynamic loop model to investigate the hemocytocompatibility and host cell activation of vascular medical devices

In this study, the hemocompatibility of tubes with an inner diameter of 5 mm made of polyvinyl chloride (PVC) and coated with different bioactive conjugates was compared to uncoated PVC tubes, latex tubes, and a stent for intravascular application that was placed inside the PVC tubes. Evaluation of hemocompatibility was done using an in vitro hemodynamic loop model that is recommended by the ISO standard 10993-4. The tubes were cut into segments of identical length and closed to form loops avoiding any gap at the splice, then filled with human blood and rotated in a water bath at 37 &#176;C for 3 hours. Thereafter, the blood inside the tubes was collected for the analysis of whole blood cell count, hemolysis (free plasma hemoglobin), complement system (sC5b-9), coagulation system (fibrinopeptide A), and leukocyte activation (polymorphonuclear elastase, tumor necrosis factor and interleukin-6). Host cell activation was determined for platelet activation, leukocyte integrin status and monocyte platelet aggregates using flow cytometry. The effect of inaccurate loop closure was examined with x-ray microtomography and scanning electron microscopy, that showed thrombus formation at the splice. Latex tubes showed the strongest activation of both plasma and cellular components of the blood, indicating a poor hemocompatibility, followed by the stent group and uncoated PVC tubes. The coated PVC tubes did not show a significant decrease in platelet activation status, but showed an increased in complement and coagulation cascade compared to uncoated PVC tubes. The loop model itself did not lead to the activation of cells or soluble factors, and the hemolysis level was low. Therefore, the presented in vitro hemodynamic loop model avoids excessive activation of blood components by mechanical forces and serves as a method to investigate in vitro interactions between donor blood and vascular medical devices.

All presented data, except FACS plots, were analyzed with a statistics software. The FACS plots were analyzed using flow cytometry software.
The analysis of whole blood cell count did not show any significant differences with respect to erythrocytes between all tested conditions (Figure 2). But, platelets and leukocytes were drastically reduced in the latex group, indicating a very poor biocompatibility of latex. This is further underlined by increased levels of free hemoglobin in the latex group, indicating the fact that except for the latex group, none of the other vascular devices or conditions led to extensive hemolysis (Figure 2). Further, the coated PVC tubes, polyPVC and hepPVC, as well as the tested stent did not lead to thrombosis by means of platelet and leukocyte loss, while latex exhibited the highest platelet and leukocyte loss, followed by uncoated PVC tubes that showed a decreased trend.
While all the tested vascular devices led to increased activation of the coagulation system (FPA) and complement component (sC5b-9), the hepPVC loops exhibited a trend for decreased levels of FPA and sC5b-9 when compared specifically to polyPVC loops (Figure 3). Interestingly, uncoated PVC and Gap loops showed lower levels of FPA compared to polyPVC, though not reaching the level of statistical significance. Nevertheless, latex loops exhibited significantly increased levels of FPA when compared to baseline and static conditions.
In accordance with the whole blood cell counts, latex loops exhibited highest levels of TNF, IL-6 and PMN elastase (Figure 4), reaching the level of statistical significance when compared to rest of the groups in terms of TNF and IL-6 (Figure 4A,B), whereas to static and baseline conditions in terms of PMN elastase (Figure 4C). These results indicate the potent activation of leukocytes by latex. The baseline levels of activation markers were always comparable to static conditions, indicating a proper heparinization of the blood.
Interestingly, it was shown that platelet and leukocyte counts for gap induced loops were only slightly reduced with moderate activation of the coagulatory system (FPA) and leukocytes (PMN elastase), though improper loop closure with resulting flow turbulences and blood contact to the uncoated, rough cutting surface led to macroscopically visible clots at the splice (Figure 1F). The clots and its distribution over the whole splice surface were evident with &#181;CT and SEM images, while no clot was found when the loops were closed with the external closing device leaving no gap between the loop endings (Figure 5).
Flow cytometric analysis of host blood cells that were stained with platelet specific markers, CD41 and platelet activation marker CD62P, are shown in Figure 6A,B. Here, the latex tubes exhibited exceedingly high median fluorescence intensity (MFI) for CD62P on blood platelets, followed by stent, whereas heparin coated polyPVC tubes exhibited minimal activation of platelets depicting anti-thrombogenic property of polyPVC tubes. Furthermore, leukocytes were classified based on the CD45 and SSC (side scatter) based granularity into (i) granulocytes; (ii) monocytes and (iii) lymphocytes (Figure 7), and the expression of CD162+ integrin was detected on each subpopulation of leukocytes that are known to interact with the CD62P on platelets24. It was noticed that the integrin expressions were drastically reduced on granulocytes and lymphocytes in latex loops. This result was in line with lowered levels of total frequencies of leukocytes in the latex loops (Figure 2). In general, the integrin levels were higher among monocytes when compared to granulocytes and lymphocytes, indicating the likelihood for the monocyte interaction with activated platelets. In this regard, monocyte platelet aggregates were also evaluated by staining the blood cells with CD14 (as monocyte marker) and CD41 (as platelet marker) and ultimately to identify double positive cells i.e. CD14+CD41+MPA (Figure 8). Here, we noticed that the stent group exhibited the highest levels of CD41 expression on the MPA, followed by the latex group, indicating an increased tendency to form MPA, despite the reduced frequency of monocyte (&#60;1 %) in the latex loops.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/61570/61570fig01.jpg" /> 
Figure 1: Overview of the in vitro hemodynamic loop model and its modifications.&#160;(A) Loop for the gap experiment with external loop closing system, leaving no gap at the splice. (B) Loop made of polyPVC coated PVC tube and stent inside (arrow). (C) Loop made of latex tube. (D) Loop for the gap experiment without the external loop closing system leaving a gap between the tube endings (arrow). (E) Loops placed in the loop cradle inside the water bath and filled with blood. (F) Thrombus resulting in a gap at the splice (arrow) after rotation. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/61570/61570fig02.jpg" /> 
Figure 2: Results for blood cell count and plasma hemoglobin.&#160;(A) Erythrocytes count. (B) Platelets count. (F) Leukocytes count. (D) Free plasma hemoglobin. The results indicate the poor biocompatibility of latex, leading to excessive hemolysis. Data are presented as mean value; error bars indicate SEM. n=1. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/61570/61570fig03.jpg" /> 
Figure 3: Results for activation of the coagulation and complement system.&#160;(A) Coagulation system activation, measured by levels of Fibrinopeptide A (FPA) (B) Complement system activation, measured by levels of sC5b-9. While latex tubes evoked significant elevated levels of the FPA, the complement activation was strong for all tested materials. Data are presented as mean value, error bars indicate SEM. *p&#60;0.05, n=1. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/61570/61570fig04.jpg" /> 
Figure 4: Leukocyte activation markers.&#160;(A) Tumor necrosis factor alpha (TNF). (B) Interleukin 6 (IL-6) (C) PMN Elastase. The results indicate increased activation of leukocytes due to elevated levels of the analyzed markers, followed by stent loops, that only led to increased levels for PMN Elastase but not TNF or IL-6. Data are presented as mean value, error bars indicate SEM. *p&#60;0.5; **p&#60;0.01, n=1. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/61570/61570fig05.jpg" /> 
Figure 5: Imaging of the splice of the loops.&#160;(A) &#181;-computer tomography (&#181;CT) of loops with improper closing (gap). The red areas indicate thrombus material. (B) Rendering of the luminal side of the tube. The rectangular selection indicates the area for scanning electron microscopy (SEM) (C). (D) &#181;CT of loops with external loop closing device and no gap at the splice, and (E) rendering and view of the luminal surface. No thrombus material was found. (F) SEM image of the rectangular selection in (E). No thrombus material was found on the cutting surface. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig05large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/61570/61570fig06.jpg" /> 
Figure 6: FACS plot for platelet activation (CD62P).&#160;(A) Representative FACS plot (basic condition) showing the blood CD41+ platelets. (B) Graph showing the platelet activation status reflected by the mean fluorescence intensity (MFI) of the different types of vascular devices in comparison to the static RT and baseline conditions. The data bars present data from single measurements. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig06large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 7" class="xfigimg" src="/files/ftp_upload/61570/61570fig07.jpg" /> 
Figure 7: FACS plot for leukocyte integrin (CD162).&#160;(A) Representative FACS plot (basic condition) showing the blood CD45+ leukocytes and subgroups (B) Graph showing the leukocyte CD162+ integrin mean fluorescence intensity (MFI) of the different types of vascular devices in comparison to the static and baseline conditions. The data bars present data from single measurements. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig07large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 8" class="xfigimg" src="/files/ftp_upload/61570/61570fig08.jpg" /> 
Figure 8: FACS plot for platelet monocyte aggregates (CD41/CD14).&#160;(A) Representative FACS plot (basic condition) showing the gating for blood monocytes (CD45+/CD14+), platelets (CD41+) and monocyte platelet aggregates (CD41+/CD14+) (B) Graph showing the CD41+ mean fluorescence intensity (MFI) on monocyte platelet aggregates for the various vascular devices compared to the static and baseline conditions. The data bars present data from single measurements. <a href="https://www.jove.com/files/ftp_upload/61570/61570fig08large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about An In Vitro Hemodynamic Loop Model to Investigate the Hemocytocompatibility and Host Cell Activation of Vascular Medical Devices at JoVE.com

An In Vitro Hemodynamic Loop Model to Investigate the Hemocytocompatibility and Host Cell Activation of Vascular Medical Devices

Presented here is a protocol for a standardized in vitro hemodynamic loop model. This model allows to test the hemocompatibility of perfusion tubes or vascular stents to be in accordance with ISO (International Organization for Standardization) standard 10993-4.

In this study, the hemocompatibility of tubes with an inner diameter of 5 mm made of polyvinyl chloride (PVC) and coated with different bioactive ...

an-vitro-hemodynamic-loop-model-to-investigate-hemocytocompatibility

Research

JoVE Journal

Medicine

6.9K Views.  Otto-von-Guericke-University. Presented here is a protocol for a standardized in vitro hemodynamic loop model. This model allows to test the hemocompatibility of perfusion tubes or vascular stents to be in accordance with ISO (International Organization for Standardization) standard 10993-4.

Video: An In Vitro Hemodynamic Loop Model to Investigate the Hemocytocompatibility and Host Cell Activation of Vascular Medical Devices

Stem Cell Transplantation in an in vitro Simulated Ischemia/Reperfusion Model

Stem cell transplantation protocols are finding their way into clinical practice1,2,3. Getting better results, making the protocols more robust, and finding new sources for implantable cells are the focus of recent research4,5. Investigating the effectiveness of cell therapies is not an easy task and new tools are needed to investigate the mechanisms involved in the treatment process6. We designed an experimental protocol of ischemia/reperfusion in order to allow the observation of cellular connections and even subcellular mechanisms during ischemia/reperfusion injury and after stem cell transplantation and to evaluate the efficacy of cell therapy. H9c2 cardiomyoblast cells were placed onto cell culture plates7,8. Ischemia was simulated with 150 minutes in a glucose free medium with oxygen level below 0.5%. Then, normal media and oxygen levels were reintroduced to simulate reperfusion. After oxygen glucose deprivation, the damaged cells were treated with transplantation of labeled human bone marrow derived mesenchymal stem cells by adding them to the culture. Mesenchymal stem cells are preferred in clinical trials because they are easily accessible with minimal invasive surgery, easily expandable and autologous. After 24 hours of co-cultivation, cells were stained with calcein and ethidium-homodimer to differentiate between live and dead cells. This setup allowed us to investigate the intercellular connections using confocal fluorescent microscopy and to quantify the survival rate of postischemic cells by flow cytometry. Confocal microscopy showed the interactions of the two cell populations such as cell fusion and formation of intercellular nanotubes. Flow cytometry analysis revealed 3 clusters of damaged cells which can be plotted on a graph and analyzed statistically. These populations can be investigated separately and conclusions can be drawn on these data on the effectiveness of the simulated therapeutical approach.

Stem Cell Transplantation in an in vitro Simulated Ischemia/Reperfusion Model

We demonstrate how to set up an in vitro ischemia/reperfusion model and how to evaluate the effect of stem cell therapy on postischemic cardiac cells.

Stem cell transplantation protocols are finding their way into clinical practice1,2,3. Getting better results, making the protocols more robust, and ...

Using Quantitative Real-time PCR to Determine Donor Cell Engraftment in a Competitive Murine Bone Marrow Transplantation Model

Murine bone marrow transplantation models provide an important tool in measuring hematopoietic stem cell (HSC) functions and determining genes/molecules that regulate HSCs. In these transplant model systems, the function of HSCs is determined by the ability of these cells to engraft and reconstitute lethally irradiated recipient mice. Commonly, the donor cell contribution/engraftment is measured by antibodies to donor- specific cell surface proteins using flow cytometry. However, this method heavily depends on the specificity and the ability of the cell surface marker to differentiate donor-derived cells from recipient-originated cells, which may not be available for all mouse strains. Considering the various backgrounds of genetically modified mouse strains in the market, this cell surface/ flow cytometry-based method has significant limitations especially in mouse strains that lack well-defined surface markers to separate donor cells from congenic recipient cells. Here, we reported a PCR-based technique to determine donor cell engraftment/contribution in transplant recipient mice. We transplanted male donor bone marrow HSCs to lethally irradiated congenic female mice. Peripheral blood samples were collected at different time points post transplantation. Bone marrow samples were obtained at the end of the experiments. Genomic DNA was isolated and the Y chromosome specific gene, Zfy1, was amplified using quantitative Real time PCR. The engraftment of male donor-derived cells in the female recipient mice was calculated against standard curve with known percentage of male vs. female DNAs. Bcl2 was used as a reference gene to normalize the total DNA amount. Our data suggested that this approach reliably determines donor cell engraftment and provides a useful, yet simple method in measuring hematopoietic cell reconstitution in murine bone marrow transplantation models. Our method can be routinely performed in most laboratories because no costly equipment such as flow cytometry is required.

Determining donor cell engraftment presents a challenge in mouse bone marrow transplant models that lack well-defined phenotypical markers. We described a methodology to quantify male donor cell engraftment in female transplant recipient mice. This method can be used in all mouse strains for the study of HSC functions.

Murine bone marrow transplantation models provide an important tool in measuring hematopoietic stem cell (HSC) functions and determining genes/molecules ...

Excitotoxic Stimulation of Brain Microslices as an In vitro Model of Stroke

Examining molecular mechanisms involved in neuropathological conditions, such as ischemic stroke, can be difficult when using whole animal systems. As such, primary or &#39;neuronal-like&#39; cell culture systems are commonly utilized. While&#160;these systems are relatively easy to work with, and are useful model systems in which various functional outcomes (such as cell death) can be readily quantified, the examined outcomes and pathways in cultured immature neurons (such as excitotoxicity-mediated cell death pathways) are not necessarily the same as those observed in mature brain, or in intact tissue. Therefore, there is the need to develop models in which cellular mechanisms in mature neural tissue can be examined. We have developed an in vitro technique that can be used to investigate a variety of molecular pathways in intact nervous tissue. The technique described herein utilizes rat cortical tissue, but this technique can be adapted to use tissue from a variety of species (such as mouse, rabbit, guinea pig, and chicken) or brain regions (for example, hippocampus, striatum, etc.). Additionally, a variety of stimulations/treatments can be used (for example, excitotoxic, administration of inhibitors, etc.). In conclusion, the brain slice model described herein can be used to examine a variety of molecular mechanisms involved in excitotoxicity-mediated brain injury.

Excitotoxic Stimulation of Brain Microslices as an In vitro Model of Stroke

We have developed a brain slice model which can be used to examine molecular mechanisms involved in excitotoxicity-mediated brain injury.&#160;This technique generates viable mature brain tissue and reduces animal numbers required for experimentation, whilst keeping the neuronal circuitry, cellular interactions, and postsynaptic compartments partly intact.

Examining molecular mechanisms involved in neuropathological conditions, such as ischemic stroke, can be difficult when using whole animal systems. As ...

Monitoring of Systemic and Hepatic Hemodynamic Parameters in Mice

The use of mouse models in experimental research is of enormous importance for the study of hepatic physiology and pathophysiological disturbances. However, due to the small size of the mouse, technical details of the intraoperative monitoring procedure suitable for the mouse were rarely described. Previously we have reported a monitoring procedure to obtain hemodynamic parameters for rats. Now, we adapted the procedure to acquire systemic and hepatic hemodynamic parameters in mice, a species ten-fold smaller than rats. This film demonstrates the instrumentation of the animals as well as the data acquisition process needed to assess systemic and hepatic hemodynamics in mice. Vital parameters, including body temperature, respiratory&#160;rate&#160;and heart&#160;rate were recorded throughout the whole procedure. Systemic hemodynamic parameters consist of carotid artery pressure (CAP) and central venous pressure (CVP). Hepatic perfusion parameters include portal vein pressure (PVP), portal flow rate as well as the flow rate of the common hepatic artery (table 1). Instrumentation and data acquisition to record the normal values was completed within 1.5 h. Systemic and hepatic hemodynamic parameters remained within normal ranges during this procedure.
This procedure is challenging but feasible. We have already applied this procedure to assess hepatic hemodynamics in normal mice as well as during 70% partial hepatectomy and in liver lobe clamping experiments. Mean PVP after resection (n= 20), was 11.41&#177;2.94 cmH2O which was significantly higher (P&#60;0.05) than before resection (6.87&#177;2.39 cmH2O). The results of liver lobe clamping experiment indicated that this monitoring procedure is sensitive and suitable for detecting small changes in portal pressure and portal flow rate. In conclusion, this procedure is reliable in the hands of an experienced micro-surgeon but should be limited to experiments where mice are absolutely needed.

This film demonstrates how to acquire systemic and hepatic hemodynamics in mice. The whole monitoring includes acquisition of vital parameters, systemic blood pressure, central venous pressure, common hepatic artery flow rate, and portal vein pressure as well as the portal flow rate in mice.

The use of mouse models in experimental research is of enormous importance for the study of hepatic physiology and pathophysiological disturbances. ...

Assessment of Perigenital Sensitivity and Prostatic Mast Cell Activation in a Mouse Model of Neonatal Maternal Separation

Chronic prostatitis/chronic pelvic pain syndrome (CP/CPPS) has a lifetime prevalence of 14% and is the most common urological diagnosis for men under the age of 50, yet it is the least understood and studied chronic pelvic pain disorder. A significant subset of patients with chronic pelvic pain report having experienced early life stress or abuse, which can markedly affect the functioning and regulation of the hypothalamic-pituitary-adrenal (HPA) axis. Mast cell activation, which has been shown to be increased in both urine and expressed prostatic secretions of CP/CPPS patients, is partially regulated by downstream activation of the HPA axis. Neonatal maternal separation (NMS) has been used for over two decades to study the outcomes of early life stress in rodent models, including changes in the HPA axis and visceral sensitivity. Here we provide a detailed protocol for using NMS as a preclinical model of CP/CPPS in male C57BL/6 mice. We describe the methodology for performing NMS, assessing perigenital mechanical allodynia, and histological evidence of mast cell activation. We also provide evidence that early psychological stress can have long-lasting effects on the male urogenital system in mice.

We are measuring perigenital mechanical sensitivity and mast cell activation in the prostate of male C57BL/6 mice that underwent an early life stress paradigm &#8211; neonatal maternal separation, in order to induce a preclinical model of chronic prostatitis/chronic pelvic pain syndrome.

Chronic prostatitis/chronic pelvic pain syndrome (CP/CPPS) has a lifetime prevalence of 14% and is the most common urological diagnosis for men under the ...

Using the Sleeve Technique in a Mouse Model of Aortic Transplantation - An Instructional Video

Orthotopic aortic transplantation using the sleeve technique reduces injury to the aorta with failure rate of only 10-20%. The time to anastomose the aorta in mice using the sleeve method was short and easy averaging 20 min, permitting studies of iso/allo grafts. The following article describes the aortic transplantation procedure used in our laboratory. The mice were anesthetized with a mixture of 1.5% volume isoflurane and 100% oxygen through a face mask. At this point, the segment of the aorta between the renal arteries and its bifurcation was separated from the vena cava, freely prepared and clampedat the proximal and distal segments with a single silk suture. Prior to the removal of the aorta, a saline solution containing heparin was injected into the inferior vena cava. Then the aorta was cut between the clamps and a saline heparin solution was used to flush the lumen. The sleeve technique with monofilament sutures was used in order to transplant the abdominal aorta in the orthotopic position.

We present an orthotopic aortic transplantation model using the sleeve technique in mice. It is a very rapid anastomosis method, which can be employed in studies of vascular disease.

Orthotopic aortic transplantation using the sleeve technique reduces injury to the aorta with failure rate of only 10-20%. The time to anastomose the ...

An Optimized Evans Blue Protocol to Assess Vascular Leak in the Mouse

Vascular leak, or plasma extravasation, has a number of causes, and may be a serious consequence or symptom of an inflammatory response. This study may ultimately lead to new knowledge concerning the causes of or new ways to inhibit or treat plasma extravasation. It is important that researchers have the proper tools, including the best methods available, for studying plasma extravasation. In this article, we describe a protocol, using the Evans blue dye method, for assessing plasma extravasation in the organs of FVBN mice. This protocol is intentionally simple, to as great a degree as possible, but provides high quality data. Evans blue dye has been chosen primarily because it is easy for the average laboratory to use. We have used this protocol to provide evidence and support for the hypothesis that the enzyme neprilysin may protect the vasculature against plasma extravasation. However, this protocol may be experimentally used and easily adapted for use in other strains of mice or in other species, in many different organs or tissues, for studies which may involve other factors that are important in understanding, preventing, or treating plasma extravasation. This protocol has been extensively optimized and modified from existing protocols, and combines reliability, ease of use, economy, and general availability of materials and equipment, making this protocol superior for the average laboratory to use in quantifying plasma extravasation from organs.

In this article, an economical, optimized, and simple protocol is described which uses the Evans blue dye method for assessing plasma extravasation in the organs of FVBN mice that can be adapted for use in other strains, species, and other organs or tissues.

Vascular leak, or plasma extravasation, has a number of causes, and may be a serious consequence or symptom of an inflammatory response. This study may ...

Hemocompatibility Testing of Blood-Contacting Implants in a Flow Loop Model Mimicking Human Blood Flow

The growing use of medical devices (e.g., vascular grafts, stents, and cardiac catheters) for temporary or permanent purposes that remain in the body&#39;s circulatory system demands a reliable and multiparametric approach that evaluates the possible hematologic complications caused by these devices (i.e., activation and destruction of blood components). Comprehensive in vitro hemocompatibility testing of blood-contacting implants is the first step towards successful in vivo implementation. Therefore, extensive analysis according to the International Organization for Standardization 10993-4 (ISO 10993-4) is mandatory prior to clinical application. The presented flow loop describes a sensitive model to analyze the hemostatic performance of stents (in this case, neurovascular) and reveal adverse effects. The use of fresh human whole blood and gentle blood sampling are essential to avoid the preactivation of blood. The blood is perfused through a heparinized tubing containing the test specimen by using a peristaltic pump at a rate of 150 mL/min at 37 &#176;C for 60 min. Before and after perfusion, hematologic markers (i.e., blood cell count, hemoglobin, hematocrit, and plasmatic markers) indicating the activation of leukocytes (polymorphonuclear [PMN]-elastase), platelets (&#946;-thromboglobulin [&#946;-TG]), the coagulation system (thombin-antithrombin III [TAT]), and the complement cascade (SC5b-9) are analyzed. In conclusion, we present an essential and reliable model for extensive hemocompatibility testing of stents and other blood-contacting devices prior to clinical application.

This protocol describes a comprehensive hemocompatibility evaluation of blood-contacting devices using laser-cut neurovascular implants. A flow loop model with fresh, heparinized human blood is applied to mimic blood flow. After perfusion, various hematologic markers are analyzed and compared to the values gained directly after blood collection for hemocompatibility evaluation of the tested devices.

The growing use of medical devices (e.g., vascular grafts, stents, and cardiac catheters) for temporary or permanent purposes that remain in the ...

Organ Ischemia-Reperfusion Injury by Simulating Hemodynamic Changes in Rat Liver Transplant Model

Orthotopic liver transplantation (OLT) in rats is a tried and proven animal model used for preoperative, intraoperative, and postoperative studies, including ischemia-reperfusion injury (IRI) of extrahepatic organs. This model requires numerous experiments and devices. The duration of anhepatic phase is closely related to the time to develop IRI after transplantation. In this experiment, we used hemodynamic changes to induce extrahepatic organ damage in rats and determined the maximum tolerance time. The time until the most severe organ injury varied for different organs. This method can easily be replicated and can also be used to study IRI of the extrahepatic organs after liver transplantation.

This paper provides a detailed description of how to build an animal model of the anhepatic phase (liver ischemia) in rats to facilitate basic research into ischemia-reperfusion injury after liver transplantation.

Orthotopic liver transplantation (OLT) in rats is a tried and proven animal model used for preoperative, intraoperative, and postoperative studies, ...

Isolation of Intrapulmonary Artery and Smooth Muscle Cells to Investigate Vascular Responses

The intrapulmonary artery (IPA) and vascular smooth muscle cells (VSMCs) isolated from rat lungs can be used to study the underlying mechanisms of vasoconstriction and vasorelaxation. After isolating the IPA and VSMCs, the characteristics of vascular responses in physiological and pathological conditions can be assessed in the absence of extrinsic factors such as nerve signals, hormones, cytokines, etc. Thus, the IPA and VSMCs serve as excellent models for studying vascular physiology/pathophysiology, along with various experimental investigations, such as modulation by pharmacological agents, patch-clamp electrophysiological analysis, calcium imaging, etc. Here, we have used a technique for isolating the IPA to investigate vascular responses in an organ bath setup. IPA segments were mounted on the organ bath chamber via intraluminal wires and stimulated by various pharmacological agents. The changes in IPA vascular tone (i.e., vasoconstriction and vasorelaxation), were recorded using an isometric force transducer and physiological data analysis software program. We implemented several experimental protocols, which can be adapted to investigate the mechanisms of vasorelaxation/vasoconstriction for studying the pharmacological activities of phytochemical or synthetic drugs. The protocols can also be used to evaluate drugs&#39; roles in modulating various diseases, including pulmonary arterial hypertension. The IPA model allows us to investigate the concentration-response curve, which is crucial in assessing drugs&#39; pharmacodynamic parameters.

Vascular responses of arterial pulmonary circulation can be explored using intrapulmonary artery (IPA) and vascular smooth muscle cells (VSMCs). The present study describes the isolation of IPA in detail and the protocols used for investigating vasorelaxation in response to physiological stimuli.