Dispersion of Nanomaterials in Aqueous Media: Towards Protocol Optimization

The sonication process is commonly used for de-agglomerating and dispersing nanomaterials in aqueous based media, necessary to improve homogeneity and ...

National Physical Laboratory

The precise use of nanoparticles in technological applications requires control over their surface properties. This implies the ability to quantitatively describe, for example, molecular coatings in terms of their thickness, areal mass, or number of molecules. Here, the authors describe two different approaches to the measurement of these parameters by using gold nanoparticles ranging in diameter from 10 to 80 nm and coated with three different proteins: immunoglobulin G, bovine serum albumin, and a peptide. One approach utilizes ultraviolet-visible spectroscopy, dynamic light scattering, and differential centrifugal sedimentation to measure the protein shell refractive indices and thicknesses, from which the number of molecules in the protein shell can be derived. The other approach employs x-ray photoelectron spectroscopy to measure the thickness of the dry molecular coatings and also to derive the number of molecules in the protein shell. The authors demonstrate that the two approaches, although very different, produce consistent measurement results. This finding is important to extend the quantitative analysis of nanoparticle molecular coatings to a wide range of materials.

Analysis of protein coatings on gold nanoparticles by XPS and liquid-based particle sizing techniques.

This paper describes the production and characteristics of the nanoparticle test materials prepared for common use in the collaborative research project NanoChOp (Chemical and optical characterization of nanomaterials in biological systems), in casu suspensions of silica nanoparticles and CdSe/CdS/ZnS quantum dots (QDs). This paper is the first to illustrate how to assess whether nanoparticle test materials meet the requirements of a "reference material" (ISO Guide 30, 2015) or rather those of the recently defined category of "representative test material (RTM)" (ISO/TS 16195, 2013). The NanoChOp test materials were investigated with small-angle X-ray scattering (SAXS), dynamic light scattering (DLS), and centrifugal liquid sedimentation (CLS) to establish whether they complied with the required monomodal particle size distribution. The presence of impurities, aggregates, agglomerates, and viable microorganisms in the suspensions was investigated with DLS, CLS, optical and electron microscopy and via plating on nutrient agar. Suitability of surface functionalization was investigated with attenuated total reflection Fourier transform infrared spectrometry (ATR-FTIR) and via the capacity of the nanoparticles to be fluorescently labeled or to bind antibodies. Between-unit homogeneity and stability were investigated in terms of particle size and zeta potential. This paper shows that only based on the outcome of a detailed characterization process one can raise the status of a test material to RTM or reference material, and how this status depends on its intended use.

Reference materials and representative test materials to develop nanoparticle characterization methods: the NanoChOp project case.

The contact of nanoparticles with biological fluids such as serum results in rapid adsorption of proteins at the nanoparticle surface in a layer known as the "protein corona". Protein coatings modify and control the behavior of the nanoparticles potentially altering the aggregation state and cellular response, which may influence their fate and hazard to human health. Cells are likely to interact with the protein interface rather than with bare surface; therefore it is important to study the protein layer and develop appropriate measurement tools. In this study we investigate how adsorbed proteins from serum affect the size and the surface charge of plain and aminated silica nanoparticles. Particle size and size distributions in buffer and serum-based biological media were studied using tunable resistive pulse sensing (TRPS), as well as differential centrifugal sedimentation (DCS) and dynamic light scattering (DLS). Average and single particle ζ-potentials (related to surface charge) were also measured by electrophoretic light scattering (ELS) and TRPS, respectively. Size measurements showed an increase in size of the nanoparticles upon acquisition of a protein layer, thus allowing an estimation of its thickness. DLS proved incapable of providing an accurate measurement of the nanoparticles' size in serum due to the presence of agglomerates. The ability of TRPS to measure sample agglomeration was investigated by comparison with the high resolution technique of DCS. Particle-by-particle ζ-potential measurements by TRPS were consistent with those performed with ELS and allowed a description of the ζ-potential distribution within the samples.

Size and ζ-Potential Measurement of Silica Nanoparticles in Serum Using Tunable Resistive Pulse Sensing.

A new certified reference material for quality control of nanoparticle size analysis methods has been developed and produced by the Institute for Reference Materials and Measurements of the European Commission's Joint Research Centre. The material, ERM-FD102, consists of an aqueous suspension of a mixture of silica nanoparticle populations of distinct particle size and origin. The characterisation relied on an interlaboratory comparison study in which 30 laboratories of demonstrated competence participated with a variety of techniques for particle size analysis. After scrutinising the received datasets, certified and indicative values for different method-defined equivalent diameters that are specific for dynamic light scattering (DLS), centrifugal liquid sedimentation (CLS), scanning and transmission electron microscopy (SEM and TEM), atomic force microscopy (AFM), particle tracking analysis (PTA) and asymmetrical-flow field-flow fractionation (AF4) were assigned. The value assignment was a particular challenge because metrological concepts were not always interpreted uniformly across all participating laboratories. This paper presents the main elements and results of the ERM-FD102 characterisation study and discusses in particular the key issues of measurand definition and the estimation of measurement uncertainty.

Challenges in the size analysis of a silica nanoparticle mixture as candidate certified reference material.

We report the results of a VAMAS (Versailles Project on Advanced Materials and Standards) inter-laboratory study on the measurement of the shell thickness and chemistry of nanoparticle coatings. Peptide-coated gold particles were supplied to laboratories in two forms: a colloidal suspension in pure water and; particles dried onto a silicon wafer. Participants prepared and analyzed these samples using either X-ray photoelectron spectroscopy (XPS) or low energy ion scattering (LEIS). Careful data analysis revealed some significant sources of discrepancy, particularly for XPS. Degradation during transportation, storage or sample preparation resulted in a variability in thickness of 53 %. The calculation method chosen by XPS participants contributed a variability of 67 %. However, variability of 12 % was achieved for the samples deposited using a single method and by choosing photoelectron peaks that were not adversely affected by instrumental transmission effects. The study identified a need for more consistency in instrumental transmission functions and relative sensitivity factors, since this contributed a variability of 33 %. The results from the LEIS participants were more consistent, with variability of less than 10 % in thickness and this is mostly due to a common method of data analysis. The calculation was performed using a model developed for uniform, flat films and some participants employed a correction factor to account for the sample geometry, which appears warranted based upon a simulation of LEIS data from one of the participants and comparison to the XPS results.

Versailles Project on Advanced Materials and Standards Interlaboratory Study on Measuring the Thickness and Chemistry of Nanoparticle Coatings Using XPS and LEIS.

Understanding and controlling the performance of engineered nanoparticle (NP) systems is greatly assisted by quantitative characterization of their coatings. Useful measurements methods have been described for NPs in liquid environment, but NP aggregation often represents a limiting factor which impairs the accuracy of techniques such as dynamic light scattering for quantification purposes. Here, the authors show how differential centrifugal sedimentation (DCS) and x-ray photoelectron spectroscopy (XPS) can provide quantitative information on the NP coating thickness, molecular conformation, and grafting density of aggregated NP samples. The authors find that thiol-terminated methoxy polyethylene glycol (mPEG) coating thickness on gold NPs increases with increasing particle size and mPEG molecular weight. The hydration of the mPEG shell was estimated by comparing the shell thickness measured in liquid by DCS and vacuum by XPS and was found to increase with the mPEG molecular weight. Finally, the authors used XPS to measure the grafting density of the mPEG molecules. This was found to depend on the mPEG molecular volume and decreased for larger mPEG molecules, suggesting that the grafting density is determined by the conformation of the mPEG molecules in liquid. This analysis provides practical measurement methods for optimizing the design of engineered NP systems and ultimately enhance and control their performance.

Chemical measurements of polyethylene glycol shells on gold nanoparticles in the presence of aggregation.

Engineered peptides capable of binding to silica have been used to provide contrast in chemical force microscopy and tested for their capacity to selectively capture silica nanoparticles (NPs). Gold coated atomic force microscopy (AFM) microcantilevers with integrated tips and colloidal probes were functionalized with engineered peptides through a thiol group of a terminal cysteine which was linked via a glycine trimer to a 12-mer binding sequence. The functionalized probes demonstrated a significantly increased binding force on silicon oxide areas of a gold-patterned silicon wafer, whereas plain gold probes, and those functionalized with a random permutation of the silica binding peptide motif or an all-histidine sequence displayed similar adhesion forces to gold and silicon oxide. As the functionalized probes also allowed contact mode imaging subsequently to the adhesion mapping, also the associated friction contrast was measured and found to be similar to the adhesion contrast. Furthermore, the adsorption of silica NPs onto planar gold surfaces functionalized in the same manner was observed to be selective. Notably, the surface coverage with silica NPs was found to decrease with increasing pH, implying the importance of electrostatic interactions between the peptide and the NPs. Finally, the adsorption of silica NPs was monitored via the decrease in fundamental resonance frequency of an AFM microcantilever functionalized with silica binding peptides.

Peptide engineered microcantilevers for selective chemical force microscopy and monitoring of nanoparticle capture.

Line-start incremental centrifugal liquid sedimentation (disc-CLS) is a powerful method to determine particle size based on the principles of Stokes' law. Because several of the input quantities of the Stokes equation cannot be easily determined for this case of a rotating disc, the disc-CLS approach relies on calibrating the sedimentation time scale with reference particles. To use these calibrant particles for establishing metrological traceability, they must fulfill the same requirements as those imposed on a certified reference material, i.e., their certified Stokes diameter and density value must come with a realistic measurement uncertainty and with a traceability statement. As is the case for several other techniques, the calibrants do not always come with uncertainties for the assigned modal diameter and effective particle density. The lack of such information and the absence of a traceability statement make it difficult for the end-user to estimate the uncertainty of the measurement results and to compare them with results obtained by others. We present the results of a collaborative study that aimed at demonstrating the traceability of particle size results obtained with disc-CLS. For this purpose, the particle size and effective particle density of polyvinyl chloride calibrants were measured using different validated methods, and measurement uncertainties were estimated according to the Guide to the Expression of Uncertainty in Measurement. The results indicate that the modal Stokes diameter and effective particle density that are assigned to the calibrants are accurate within 5% and 3.5%, respectively, and that they can be used to establish traceability of particle size results obtained with disc-CLS. This conclusion has a great impact on the traceability statement of certified particle size reference materials, for which the traceability is limited to the size and density values of the calibrant particles.

Caterina Minelli

Chemical,
Medical and Environmental Science,
Chemical, Medical and Environmental Science

National Physical Laboratory

Dispersion of Nanomaterials in Aqueous Media: Towards Protocol Optimization

Caterina Minelli

.css-o250i3{font-size:18px;font-family:Open Sans,sans-serif;line-height:21.6px;}Chemical,Medical and Environmental Science,Chemical, Medical and Environmental Science

National Physical Laboratory

Dispersion of Nanomaterials in Aqueous Media: Towards Protocol Optimization

Chemical,
Medical and Environmental Science,
Chemical, Medical and Environmental Science