multiscale-structures-aggregated-imprinted-nanofibers-for-functional

Multiscale Structures Aggregated by Imprinted Nanofibers for Functional Surfaces

Multiscale surface structures have attracted increasing interest owing to several potential applications in surface devices. However, an existing ...

Korea Institute of Machinery and Materials

In printed electronics technology, the overlay accuracy of printed patterns is a very important issue when applying printing technology to the production of electric devices. In order to achieve accurate positioning of the printed patterns, this study proposes a novel precision reverse offset printing system. Furthermore, the study evaluates the effects of synchronization and printing force on position errors of the printed patterns, and presents methods of controlling synchronization and printing force so as to eliminate positional errors caused by the above-mentioned reasons. Finally, the printing position repeatability of 0.40 μm and 0.32 μm (x and y direction, respectively) at a sigma level is obtained over the dimension of 100 mm under repeated printing tests with identical printing conditions. 

Development of a precision reverse offset printing system.

Simple, low-cost and scalable patterning methods for Cu nanowire (NW)-based flexible transparent conducting electrodes (FTCEs) are essential for the widespread use of Cu NW FTCEs in numerous flexible optoelectronic devices, wearable devices, and electronic skins. In this paper, continuous patterning for Cu NW FTCEs via a combination of selective intense pulsed light (IPL) and roll-to-roll (R2R) wiping process was explored. The development of continuous R2R patterning could be achieved because there was significant difference in adhesion properties between NWs and substrates depending on whether Cu NW coated area was irradiated by IPL or not. Using a custom-built, R2R-based wiping apparatus, it was confirmed that nonirradiated NWs could be clearly removed out without any damage on irradiated NWs strongly adhered to the substrate, resulting in continuous production of low-cost Cu NW FTCE patterns. In addition, the variations in microscale pattern size by varying IPL process parameters/the mask aperture sizes were investigated, and possible factors affecting on developed pattern size were meticulously examined. Finally, the successful implementation of the patterned Cu NW FTCEs into a phosphorescent organic light-emitting diode (PhOLED) and a flexible transparent conductive heater (TCH) were demonstrated, verifying the applicability of the patterned FTCEs. It is believed that our study is the key step toward realizing the practical use of NW FTCEs in various flexible electronic devices.

Continuous Patterning of Copper Nanowire-Based Transparent Conducting Electrodes for Use in Flexible Electronic Applications.

Recently, highly flexible conductive features have been widely demanded for the development of various electronic applications, such as foldable displays, deformable lighting, disposable sensors, and flexible batteries. Herein, we report for the first time a selective photonic sintering-derived, highly reliable patterning approach for creating extremely flexible carbon nanotube (CNT)/silver nanoparticle (Ag NP) composite electrodes that can tolerate severe bending (20 000 cycles at a bending radius of 1 mm). The incorporation of CNTs into a Ag NP film can enhance not only the mechanical stability of electrodes but also the photonic-sintering efficiency when the composite is irradiated by intense pulsed light (IPL). Composite electrodes were patterned on various plastic substrates by a three-step process comprising coating, selective IPL irradiation, and wiping. A composite film selectively exposed to IPL could not be easily wiped from the substrate, because interfusion induced strong adhesion to the underlying polymer substrate. In contrast, a nonirradiated film adhered weakly to the substrate and was easily removed, enabling highly flexible patterned electrodes. The potential of our flexible electrode patterns was clearly demonstrated by fabricating a light-emitting diode circuit and a flexible transparent heater with unimpaired functionality under bending, rolling, and folding.

Selective Light-Induced Patterning of Carbon Nanotube/Silver Nanoparticle Composite To Produce Extremely Flexible Conductive Electrodes.

Recently, the demand for stretchable strain sensors used for detecting human motion is rapidly increasing. This paper proposes high-performance strain sensors based on Ag flake/Ag nanocrystal (NC) hybrid materials incorporated into a polydimethylsiloxane (PDMS) elastomer. The addition of Ag NCs into an Ag flake network enhances the electrical conductivity and sensitivity of the strain sensors. The intense localized heating of Ag flakes/NCs is induced by intense pulsed light (IPL) irradiation, to achieve efficient sintering of the Ag NCs within a second, without damaging the PDMS matrix. This leads to significant improvement in the sensor sensitivity. Our strain sensors are highly stretchable (maximum strain = 80%) and sensitive (gauge factor = 7.1) with high mechanical stability over 10 000 stretching cycles under 50% strain. For practical demonstration, the fabrication of a smart glove for detecting the motions of fingers and a sports band for measuring the applied arm strength is also presented. This study provides an effective method for fabricating elastomer-based high-performance stretchable electronics.

A photonic sintering derived Ag flake/nanoparticle-based highly sensitive stretchable strain sensor for human motion monitoring.

A simple route to fabricate defect-free Ag-nanoparticle-carbon-nanotube composite-based high-resolution mesh flexible transparent conducting electrodes (FTCEs) is explored. In the selective photonic sintering-based patterning process, a highly soft rubber or thin plastic substrate is utilized to achieve close and uniform contact between the composite layer and photomask, with which uniform light irradiation can be obtained with diminished light diffraction. This well-controlled process results in developing a fine and uniform mesh pattern (≈12 μm). The mesh patternability is confirmed to be dependent on heat distribution in the selectively light-irradiated film and the pattern design for FTCE could be adopted for more precise patterns with desired performance. Moreover, using a very thin substrate could allow the mesh to be positioned closer to the strain-free neutral mechanical plane. Due to strong interfacial adhesion between the mesh pattern and substrate, the mesh FTCE could tolerate severe mechanical deformation without performance degradation. It is demonstrated that a transparent heater with fine mesh patterns on thin substrate can maintain stability after 100 repeated washing test cycles in which a variety of stress situations occurring in combination. The presented highly durable FTCE and simple fabrication processes may be widely adoptable for various flexible, large-area, and wearable optoelectronic devices.

Sin Kwon

Printed Electronics Research Team

Korea Institute of Machinery and Materials

Multiscale Structures Aggregated by Imprinted Nanofibers for Functional Surfaces