We acknowledge support from the National Natural Science Foundation of China (NSFC) under grant numbers 11621062, 11772294, U1530402, and 11811530001. This research was also partially supported by the China Postdoctoral Science Foundation (2021M690044). This research used the resources of the Advanced Light Source, which is a DOE Office of Science User Facility under contract number DE-AC02-05CH11231 and the Shanghai Synchrotron Radiation Facility. This research was partially supported by COMPRES, the Consortium for Materials Properties Research in Earth Sciences under NSF Cooperative Agreement EAR 1606856.

1. Sample preparation
<ol>
	<li>Obtain 3 nm, 20 nm, 40 nm, 70 nm, 100 nm, 200 nm, and 500 nm nickel powder from commercial sources (see Table of Materials). The morphology characterization is shown in Figure 1.</li>
	<li>Prepare 8 nm nickel particles by heating 3 nm nickel particles using a reaction kettle (see Table of Materials).
	<ol>
		<li>Put ~20 mL of absolute ethanol and ~50 mg of 3 nm nickel powder into the reaction kettle. NOTE: T...

Computational simulations have been widely employed to study the grain size effect on the strength of nanometals5,6,16,17,27,42. Perfect dislocations, partial dislocations, and GB deformation have been proposed to play decisive roles in the deformation mechanisms of the nanomaterials. In a molecular dynamics simulation, Yamak...

The resistance to plastic deformation determines the materials&#39; strength. The strength of the metals usually increases with the decreasing grain sizes. This size strengthening phenomenon can be well illustrated by the traditional Hall-Petch relationship theory from the millimeter down to submicron regime1,2, which is based on the dislocation-mediated deformation mechanism of bulk-sized metals, i.e., dislocations pile up at grain boundaries (GBs) and hinder their motions, leading to the mechanical strengthening in metals3,4.
In contrast, mechanical softening, often referred to as the inverse Hall-Petch relationship, has been reported for fine nanometals in the last two decades5,6,7,8,9,10. Therefore, the strength of the nanometals is still puzzling as continuous hardening was detected for grain sizes down to ~10 nm11,12, while the cases of size softening below 10 nm regime were also reported7,8,9,10. The main difficulty or challenge for this debated topic is to make statistically reproducible measurements on the mechanical properties of ultrafine nanometals and establish a reliable correlation between the strength and grain size of the nanometals. Another part of the difficulty comes from the ambiguity in the plastic deformation mechanisms of the nanometals. Various defects or processes at nanoscale have been reported, including dislocations13,14, deformation twinning15,16,17, stacking faults15,18, GB migration19, GB sliding5,6,20,21, grain rotation22,23,24, atomic bond parameters25,26,27,28, etc. However, which one dominates the plastic deformation and thus determines the strength of nanometals is still unclear.
For these above issues, traditional approaches of mechanical strength examining, such as tensile test29, Vickers hardness test30,31, nano-indentation test32, micropillar compression33,34,35, etc. are less effective because the high quality of large pieces of nanostructured materials is so difficult to fabricate and conventional indenter is much larger than single nanoparticle of materials (for the single-particle mechanics). In this study, we introduce radial DAC XRD techniques36,37,38 to material science to in situ track the yield stress and deformation texturing of nano nickel of various grain sizes, which are used in the geoscience field in previous studies. It has been found that the mechanical strengthening can be extended down to 3 nm, much smaller than the previously reported most substantial sizes of nanometals, which enlarges the regime of conventional Hall-Petch relationship, implying the significance of rDAC XRD techniques to material science.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>20 nm Ni</td>
			<td>Nanomaterialstore</td>
			<td>SN1601</td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>3 nm Ni</td>
			<td>nanoComposix</td>
			<td></td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>40, 70, 100, 200, 500 nm Ni</td>
			<td>US nano</td>
			<td>US1120</td>
			<td>Flammable</td>
		</tr>
		<tr>
			<td>Absolute ethanol</td>
			<td></td>
			<td></td>
			<td>as the solution to make 8 nm Ni</td>
		</tr>
		<tr>
			<td>Absolute isopropanol</td>
			<td></td>
			<td></td>
			<td>as the solution to make 12 nm Ni</td>
		</tr>
		<tr>
			<td>Amorphous boron powder</td>
			<td>alfa asear</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Copper mesh</td>
			<td>Beijing Zhongjingkeyi Technology Co., Ltd.</td>
			<td></td>
			<td>TEM grid</td>
		</tr>
		<tr>
			<td>Epoxy glue</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Ethanol</td>
			<td></td>
			<td></td>
			<td>clean experimental setup</td>
		</tr>
		<tr>
			<td>Focused ion beam</td>
			<td>FEI</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Glass slide</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Glue tape</td>
			<td>Scotch</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Kapton</td>
			<td>DuPont</td>
			<td></td>
			<td>Polyimide film material</td>
		</tr>
		<tr>
			<td>Laser drilling machine</td>
			<td></td>
			<td></td>
			<td>located in high pressure lab of ALS</td>
		</tr>
		<tr>
			<td>Monochromatic synchrotron X-ray</td>
			<td>Beamline 12.2.2, Advanced Light Source (ALS), Lawrence Berkeley National Laboratory</td>
			<td></td>
			<td>X-ray energy: 25-30 keV</td>
		</tr>
		<tr>
			<td>Optical microscope</td>
			<td>Leica</td>
			<td></td>
			<td>to mount the gasket and load samples</td>
		</tr>
		<tr>
			<td>Pt powder</td>
			<td>thermofisher</td>
			<td>38374</td>
			<td></td>
		</tr>
		<tr>
			<td>Reaction kettle</td>
			<td>Xian Yichuang Co.,Ltd.</td>
			<td></td>
			<td>50 mL</td>
		</tr>
		<tr>
			<td>Sand paper</td>
			<td></td>
			<td></td>
			<td>from 400 mesh to 1000 mesh</td>
		</tr>
		<tr>
			<td>Transmission Electron Microscopy</td>
			<td>FEI</td>
			<td></td>
			<td>Titan G2 60-300</td>
		</tr>
		<tr>
			<td>Two-dimension image plate</td>
			<td>ALS, BL 12.2.2</td>
			<td></td>
			<td>mar 345</td>
		</tr>
	</tbody>
</table>

determining the mechanical strength of ultra-fine-grained metals

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size dependence of the strength of the nanometals has been attracting a lot of interest. However, characterizing the strength of materials at the lower nanometer scale has been a big challenge because the traditional techniques become no longer effective and reliable, such as nano-indentation, micropillar compression, tensile, etc. The current protocol employs radial diamond-anvil cell (rDAC) X-ray diffraction (XRD) techniques to track differential stress changes and determine the strength of ultrafine metals. It is found that ultrafine nickel particles have more significant yield strength than coarser particles, and the size strengthening of nickel continues down to 3 nm. This vital finding immensely depends on effective and reliable characterizing techniques. The rDAC XRD method is expected to play a significant role in studying and exploring nanomaterial mechanics.

Under hydrostatic compression, unrolled X-ray diffraction lines should be straight, not curved. However, under non-hydrostatic pressure, the curvature (ellipticity of the XRD rings, which translates into the non-linearity of the lines plotted along the azimuth angle) significantly increases ultrafine-grained-nickel at similar pressures (Figure 4). At a similar pressure, the differential strain of the 3 nm sized nickel is the highest. The mechanical strength results (stress-strain curves) are...

Watch this Scientific Journal Video about Determining the Mechanical Strength of Ultra-Fine-Grained Metals at JoVE.com

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

The protocol presented here describes the high-pressure radial diamond-anvil-cell experiments and analyzing the related data, which are essential for obtaining the mechanical strength of the nanomaterials with a significant breakthrough to the traditional approach.

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size ...

The grained particle allow us to track the change of different stress and determine the strength of ASFA metal, which overcome the deficiency of traditional techniques. This technique can be used to statistically examine the mechanical property of even sub 10 nanometer grain size metal with a reproducible and reliable results To prepare captain supporting gaskets, use laser drilling machine to cut the inner circle, followed by the outer rectangular part. The rectangular dimension is eight by 1.4 millimeters.Next, prepare boron epoxy gaskets from a 10 millimeter diameter boron disc by manually polishing the raw discs with sandpaper to a thickness of 60 to 100 micrometers. Then cut the inner circles and outer circle with a laser drilling machine. Repeat and stop the procedure immediately when the right sized and center drilled gasket comes off.Next, to assemble the gaskets, place a captain supporting gasket on a glass slide and place a drilled boron gasket on the inner hole of the captain gasket, ensuring that the larger end of the boron gasket is at the top. Then put another clean glass slide on the top, hold it firmly and press until the boron gasket is firmly inserted in the hole of the captain gasket. Store the fabricated gasket assemblies between two clean glass slides and wrap them with glue tape for future use.To mount the gasket assembly, mark a dot locating the center of the diamond on the computer monitor connected to the optical microscope, then mount the boron epoxy gasket and mark the center of the gasket hole. Next, use a glass slide to press down the gasket assembly such that the gasket firmly sets on the diamond of the piston. For cleaning and compacting the gasket setup, load samples with a chunk size smaller than the gasket hole, such that there is no overflow of materials on the gasket surface.After loading a new piece of sample, close the cell to achieve compactness. Use a monochromatic synchrotron x-ray to conduct diffraction experiments. Focus the x-ray beam to approximately a 30 by 30 square micrometer surface area on the sample.Collect the x-ray diffraction patterns at pressure intervals of one to two gigapascals by a two dimension image plate with a resolution of 100 micrometers per pixel. Under hydrostatic compression, unrolled x-ray dIffraction lines should be straight not curved. Under non hydrostatic pressure, the curvature significantly increases with the decreasing grain size at similar pressures, suggesting continuous mechanical strengthening.At similar pressures, the differential stress of the three nanometer sized nickel is the highest. In transmission electron microscopy images of representative nickel, quenched from around 40 gigapascals, a high content of dislocations is seen in the course grained sample as expected. In contrast, nano twins are well captured in the high pressure recovered nano crystalline nickel accompanied by some stacking faults.In short, twining induced by stacking faults observed in these measurements originates from the nucleation and motion of partial dislocations. We need to load the sample properly to ensure the chamber is full of powder and the gasket would not crack at high pressure. We can perform TM limit under recovery sample and then examine the microstructure and the deformation defect for determining the deformation mechanism.We have also used this technique to explore as a research topic such as probing green rotation at a nano scale energy reading, the ductility of the nano ceramics.

determining-the-mechanical-strength-of-ultra-fine-grained-metals

Research

Education

JoVE Core

JoVE Journal

Mechanical Engineering

Engineering

Unit 1

Concept of Stress

SCIENTISTS IN ACTION

2.0K ビュー.  Harbin Institute of Technology. 粒子粒子は、異なる応力の変化を追跡し、伝統的な技術の欠陥を克服するASFA金属の強度を決定することを可能にする。この技術は、再現性と信頼性の高い結果を持つサブ10ナノメートルの粒径の金属の機械的特性を統計的に調べるために使用することができますキャプテン支持ガスケットを準備するには、レーザー掘削機を使用して内側の円を切断し、続いて外側の長?...

ビデオ: Determining the Mechanical Strength of Ultra-Fine-Grained Metals

The protocol presented here describes the high-pressure radial diamond-anvil-cell experiments and analyzing the related data, which are essential for obtaining the mechanical strength of the nanomaterials with a significant breakthrough to the traditional...

characterization of ultra-fine grained and nanocrystalline materials using transmission kikuchi diffraction

Characterization of Ultra-fine Grained and Nanocrystalline Materials Using Transmission Kikuchi Diffraction

This paper provides a detailed method to characterize the microstructure of ultra-fine grained and nanocrystalline materials using a scanning electron microscope equipped with a standard electron backscatter diffraction system. Metal alloys and minerals presenting refined microstructures are analyzed using this technique, showing the diversity of its possible...

disentangling high strength copolymer aramid fibers to enable the determination of their mechanical properties

Disentangling High Strength Copolymer Aramid Fibers to Enable the Determination of Their Mechanical Properties

The primary goal of the study is to develop a protocol to prepare consistent specimens for accurate mechanical testing of high strength copolymer aramid fibers, by removing a coating and disentangling the individual fiber strands without introducing significant chemical or physical...

determining heat and mechanical pain threshold in inflamed skin of human subjects

Determining heat and mechanical pain threshold in inflamed skin of human subjects

Algorithms assessing heat and mechanical pain thresholds in experimentally inflamed skin of human study subjects are shown.  The two pain testing paradigms independently examine nociceptive processing by the two major peripheral nerve fiber populations transmitting pain, i.e., non-myelinated C fibers and small myelinated A-delta...

biological preparation and mechanical technique for determining viscoelastic properties of zonular fibers

Biological Preparation and Mechanical Technique for Determining Viscoelastic Properties of Zonular Fibers

The protocol describes a method for the study of extracellular matrix viscoelasticity and its dependence on protein composition or environmental factors. The matrix system targeted is the mouse zonule. The performance of the method is demonstrated by comparing the viscoelastic behavior of wild-type zonular fibers with those lacking microfibril-associated...

processing of bulk nanocrystalline metals at the us army research laboratory

Processing of Bulk Nanocrystalline Metals at the US Army Research Laboratory

This paper provides a brief overview of the ongoing efforts at the Army Research Laboratory on the processing of bulk nanocrystalline metals with an emphasis on the methodologies used for the production of the novel metal...

measuring the strength of mice

Measuring the Strength of Mice

Deficits in muscular strength occur in many clinical conditions such as motor neuron disease. The inverted screen and weight lifting tests described here measure strength in mice almost exclusively, with minimal influence of factors such as...

fine-tuning the size and minimizing the noise of solid-state nanopores

Fine-tuning the Size and Minimizing the Noise of Solid-state Nanopores

A methodology for preparing solid-state nanopores in solution for biomolecular translocation experiments is presented. By applying short pulses of high electric fields, the nanopore diameter can be controllably enlarged with subnanometer precision and its electrical noise characteristics significantly improved. This procedure is performed in situ using standard laboratory equipment under experimental...

quantification of heavy metals and other inorganic contaminants on the productivity of microalgae

Quantification of Heavy Metals and Other Inorganic Contaminants on the Productivity of Microalgae

Integration of microalgal cultivation with industrial flue gas will ultimately introduce heavy metals and other inorganic compounds into the growth media. This study presents a procedure used to determine the end fate and impact of heavy metals and inorganic contaminants on the growth of Nannochloropsis salina grown in...

determining the functional status of the corticospinal tract within one week of stroke

Determining the Functional Status of the Corticospinal Tract Within One Week of Stroke

This protocol is for evaluating corticospinal tract function within 1 week of stroke. It can be used to select and stratify patients in trials of interventions designed to improve upper limb motor recovery and outcomes and in clinical practice for predicting upper limb functional outcomes 3 months after...

indirect fabrication of lattice metals with thin sections using centrifugal casting

Indirect Fabrication of Lattice Metals with Thin Sections Using Centrifugal Casting

An indirect additive manufacturing method combining a 3D printing of polymers with a centrifugal casting is outlined for manufacturing 3D octet truss metals (Al and Cu alloys) having a unit cell length of 5 mm with a wall thickness of 0.5...

determining the contribution of the energy systems during exercise

Determining the Contribution of the Energy Systems During Exercise

This protocol allows researchers focused on exercise and sports sciences to determine the relative contribution of three different energy systems to the total energy expenditure during a large variety of...

maldi sample preparation: the ultra thin layer method

MALDI Sample Preparation: the Ultra Thin Layer Method

This video demonstrates the preparation of an ultra-thin matrix/analyte layer for analyzing peptides and proteins by Matrix-Assisted Laser Desorption Ionization Mass Spectrometry...

determining the phagocytic activity of clinical antibody samples

Determining the Phagocytic Activity of Clinical Antibody Samples

We present a high-throughput flow cytometric assay to determine the phagocytic activity of antigen-specific antibodies from clinical samples, utilizing fluorescent antigen-coated beads and a monocytic cell line expressing multiple Fc receptors&#x2014;providing receptor usage and phagocytic activity determinations in a standardized and reproducible fashion for any antigen of...

the quantification of injectability by mechanical testing

The Quantification of Injectability by Mechanical Testing

Presented here is a protocol for quantitatively evaluating the injectability of a material through a syringe-needle system using a standard mechanical testing...

in vivo evaluation of the mechanical and viscoelastic properties of the rat tongue

In Vivo Evaluation of the Mechanical and Viscoelastic Properties of the Rat Tongue

We describe a surgical procedure in an anesthetized rat model for determining the muscle tone and viscoelastic properties of the tongue. The procedure involves specific stimulation of the hypoglossal nerves and application of passive Lissajous force/deformation curves to the...

In Vivo Evaluation of the Mechanical and Viscoelastic Properties of the Rat Tongue

monitoring fine and associative motor learning in mice using the erasmus ladder

Author Spotlight: Unveiling Neural Mechanisms Through Automated Evaluation of Motor Learning and Myelin Plasticity Studies Using the Erasmus Ladder 

This article presents a protocol that allows a non-invasive and automated assessment of fine motor performance, as well as adaptive and associative motor learning upon challenges, using a device called the Erasmus Ladder. Task difficulty can be titrated to detect motor impairment ranging from major to subtle degrees.

Monitoring Fine and Associative Motor Learning in Mice Using the Erasmus Ladder

detection of extravascular trypanosoma parasites by fine needle aspiration

Detection of Extravascular Trypanosoma Parasites by Fine Needle Aspiration

Fine Needle Aspiration is a technique, whereby cells are obtained from a lesion or organ using a thin needle. Aspirated material is smeared, stained and examined under a microscope for diagnosis or used for molecular biology, cytometry or in vitro analysis. It is cheap, simple, quick and causes minimal...

Detection of Extravascular Trypanosoma Parasites by Fine Needle Aspiration

determining the initial difficulty of the motion-based acuity test

Determining the Initial Difficulty of the Motion-Based Acuity Test

synthesis of cationized magnetoferritin for ultra-fast magnetization of cells

Synthesis of Cationized Magnetoferritin for Ultra-fast Magnetization of Cells

A protocol for the synthesis and cationization of cobalt-doped magnetoferritin is presented, as well as a method to rapidly magnetize stem cells with cationized...

Determining 3D Flow Fields via Multi-camera Light Field Imaging

In the field of fluid mechanics, the resolution of computational schemes has outpaced experimental methods and widened the gap between predicted and observed phenomena in fluid flows. Thus, a need exists for an accessible method capable of resolving three-dimensional (3D) data sets for a range of problems. We present a novel technique for performing quantitative 3D imaging of many types of flow fields. The 3D technique enables investigation of complicated velocity fields and bubbly flows. Measurements of these types present a variety of challenges to the instrument. For instance, optically dense bubbly multiphase flows cannot be readily imaged by traditional, non-invasive flow measurement techniques due to the bubbles occluding optical access to the interior regions of the volume of interest. By using Light Field Imaging we are able to reparameterize images captured by an array of cameras to reconstruct a 3D volumetric map for every time instance, despite partial occlusions in the volume. The technique makes use of an algorithm known as synthetic aperture (SA) refocusing, whereby a 3D focal stack is generated by combining images from several cameras post-capture 1. Light Field Imaging allows for the capture of angular as well as spatial information about the light rays, and hence enables 3D scene reconstruction. Quantitative information can then be extracted from the 3D reconstructions using a variety of processing algorithms. In particular, we have developed measurement methods based on Light Field Imaging for performing 3D particle image velocimetry (PIV), extracting bubbles in a 3D field and tracking the boundary of a flickering flame. We present the fundamentals of the Light Field Imaging methodology in the context of our setup for performing 3DPIV of the airflow passing over a set of synthetic vocal folds, and show representative results from application of the technique to a bubble-entraining plunging jet.

A technique for performing quantitative three-dimensional (3D) imaging for a range of fluid flows is presented. Using concepts from the area of Light Field Imaging, we reconstruct 3D volumes from arrays of images. Our 3D results span a broad range including velocity fields and multi-phase bubble size distributions.

In the field of fluid mechanics, the resolution of computational schemes has outpaced experimental methods and widened the gap between predicted and ...

Fast Imaging Technique to Study Drop Impact Dynamics of Non-Newtonian Fluids

In the field of fluid mechanics, many dynamical processes not only occur over a very short time interval but also require high spatial resolution for detailed observation, scenarios that make it challenging to observe with conventional imaging systems. One of these is the drop impact of liquids, which usually happens within one tenth of millisecond. To tackle this challenge, a fast imaging technique is introduced that combines a high-speed camera (capable of up to one million frames per second) with a macro lens with long working distance to bring the spatial resolution of the image down to 10 &#181;m/pixel. The imaging technique enables precise measurement of relevant fluid dynamic quantities, such as the flow field, the spreading distance and the splashing speed, from analysis of the recorded video. To demonstrate the capabilities of this visualization system, the impact dynamics when droplets of non-Newtonian fluids impinge on a flat hard surface are characterized. Two situations are considered: for oxidized liquid metal droplets we focus on the spreading behavior, and for densely packed suspensions we determine the onset of splashing. More generally, the combination of high temporal and spatial imaging resolution introduced here offers advantages for studying fast dynamics across a wide range of microscale phenomena.

Drop impact of non-Newtonian fluids is a complex process since different physical parameters influence the dynamics over a very short time (less than one tenth of a millisecond). A fast imaging technique is introduced in order to characterize the impact behaviors of different non-Newtonian fluids.

In the field of fluid mechanics, many dynamical processes not only occur over a very short time interval but also require high spatial resolution for ...

Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity

Metal foams are interesting materials from both a fundamental understanding and practical applications point of view. Uses have been proposed, and in many cases validated experimentally, for light weight or impact energy absorbing structures, as high surface area heat exchangers or electrodes, as implants to the body, and many more. Although great progress has been made in understanding their structure-properties relationships, the large number of different processing techniques, each producing material with different characteristics and structure, means that understanding of the individual effects of all aspects of structure is not complete. The replication process, where molten metal is infiltrated between grains of a removable preform material, allows a markedly high degree of control and has been used to good effect to elucidate some of these relationships. Nevertheless, the process has many steps that are dependent on individual &#8220;know-how&#8221;, and this paper aims to provide a detailed description of all stages of one embodiment of this processing method, using materials and equipment that would be relatively easy to set up in a research environment. The goal of this protocol and its variants is to produce metal foams in an effective and simple way, giving the possibility to tailor the outcome of the samples by modifying certain steps within the process. By following this, open cell aluminum foams with pore sizes of 1&#8211;2.36 mm diameter and 61% to 77% porosity can be obtained.

Replication is one of the processing techniques used for the production of porous metal sponges. In this paper one implementation of the method for the production of open celled porous aluminum is shown in detail.

Metal foams are interesting materials from both a fundamental understanding and practical applications point of view. Uses have been proposed, and in many ...

Experiments on Ultrasonic Lubrication Using a Piezoelectrically-assisted Tribometer and Optical Profilometer

Friction and wear are detrimental to engineered systems. Ultrasonic lubrication is achieved when the interface between two sliding surfaces is vibrated at a frequency above the acoustic range (20 kHz). As a solid-state technology, ultrasonic lubrication can be used where conventional lubricants are unfeasible or undesirable. Further, ultrasonic lubrication allows for electrical modulation of the effective friction coefficient between two sliding surfaces. This property enables adaptive systems that modify their frictional state and associated dynamic response as the operating conditions change. Surface wear can also be reduced through ultrasonic lubrication. We developed a protocol to investigate the dependence of friction force reduction and wear reduction on the linear sliding velocity between ultrasonically lubricated surfaces. A pin-on-disc tribometer was built which differs from commercial units in that a piezoelectric stack is used to vibrate the pin at 22 kHz normal to the rotating disc surface. Friction and wear metrics including effective friction force, volume loss, and surface roughness are measured without and with ultrasonic vibrations at a constant pressure of 1 to 4 MPa and three different sliding velocities: 20.3, 40.6, and 87 mm/sec. An optical profilometer is utilized to characterize the wear surfaces. The effective friction force is reduced by 62% at 20.3 mm/sec. Consistently with existing theories for ultrasonic lubrication, the percent reduction in friction force diminishes with increasing speed, down to 29% friction force reduction at 87 mm/sec. Wear reduction remains essentially constant (49%) at the three speeds considered.

We present a protocol for using a piezoelectrically-assisted tribometer and optical profilometer to investigate the dependence of ultrasonic wear and friction reduction on linear velocity, contact pressure, and surface properties.

Friction and wear are detrimental to engineered systems. Ultrasonic lubrication is achieved when the interface between two sliding surfaces is vibrated at ...

One of the typical methods to manufacture 3D lattice metals is the direct-metal additive manufacturing (AM) process such as Selective Laser Melting (SLM) and Electron Beam Melting (EBM). In spite of its potential processing capability, the direct AM method has several disadvantages such as high cost, poor surface finish of final products, limitation in material selection, high thermal stress, and anisotropic properties of parts. We propose a cost-effective method to manufacture 3D lattice metals. The objective of this study is to provide a detailed protocol on fabrication of 3D lattice metals having a complex shape and a thin wall thickness; e.g., octet truss made of Al and Cu alloys having a unit cell length of 5 mm and a cell wall thickness of 0.5 mm. An overall experimental procedure is divided into eight sections: (a) 3D printing of sacrificial patterns (b) melt-out of support materials (c) removal of residue of support materials (d) pattern assembly (e) investment (f) burn-out of sacrificial patterns (g) centrifugal casting (h) post-processing for final products. The suggested indirect AM technique provides the potential to manufacture ultra-lightweight lattice metals; e.g., lattice structures with Al alloys. It appears that the process parameters should be properly controlled depending on materials and lattice geometry, observing the final products of octet truss metals by the indirect AM technique.

An indirect additive manufacturing method combining a 3D printing of polymers with a centrifugal casting is outlined for manufacturing 3D octet truss metals (Al and Cu alloys) having a unit cell length of 5 mm with a wall thickness of 0.5 mm.

One of the typical methods to manufacture 3D lattice metals is the direct-metal additive manufacturing (AM) process such as Selective Laser Melting (SLM) ...

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for determining optimal sensor and forcing locations typically require data, either simulated or measured, from the damaged structure. Embedded sensitivity functions provide an approach for determining the best available sensor location to detect damage with only data from the healthy structure. In this video and manuscript, the data acquisition procedure and best practices for determining the embedded sensitivity functions of a structure is presented. The frequency response functions used in the calculation of the embedded sensitivity functions are acquired using modal impact testing. Data is acquired and representative results are shown for a residential scale wind turbine blade. Strategies for evaluating the quality of the data being acquired are provided during the demonstration of the data acquisition process.

The data acquisition procedure for determining embedded sensitivity functions is described. Data is acquired and representative results are shown for a residential scale wind turbine blade.

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for ...

A Robotic Platform to Study the Foreflipper of the California Sea Lion

The California sea lion (Zalophus californianus), is an agile and powerful swimmer. Unlike many successful swimmers (dolphins, tuna), they generate most of their thrust with their large foreflippers. This protocol describes a robotic platform designed to study the hydrodynamic performance of the swimming California sea lion (Zalophus californianus). The robot is a model of the animal&#39;s foreflipper that is actuated by motors to replicate the motion of its propulsive stroke (the &#39;clap&#39;). The kinematics of the sea lion&#39;s propulsive stroke are extracted from video data of unmarked, non-research sea lions at the Smithsonian Zoological Park (SNZ). Those data form the basis of the actuation motion of the robotic flipper presented here. The geometry of the robotic flipper is based a on high-resolution laser scan of a foreflipper of an adult female sea lion, scaled to about 60% of the full-scale flipper. The articulated model has three joints, mimicking the elbow, wrist and knuckle joint of the sea lion foreflipper. The robotic platform matches dynamics properties&#8212;Reynolds number and tip speed&#8212;of the animal when accelerating from rest. The robotic flipper can be used to determine the performance (forces and torques) and resulting flowfields.

A robotic platform is described that will be used to study the hydrodynamic performance&#8212;forces and flowfields&#8212;of the swimming California sea lion. The robot is a model of the animal&#39;s foreflipper that is actuated by motors to replicate the motion of its propulsive stroke (the &#39;clap&#39;).

The California sea lion (Zalophus californianus), is an agile and powerful swimmer. Unlike many successful swimmers (dolphins, tuna), they generate most ...

One of the challenges in microstructure analysis nowadays resides in the reliable and accurate characterization of ultra-fine grained (UFG) and nanocrystalline materials. The traditional techniques associated with scanning electron microscopy (SEM), such as electron backscatter diffraction (EBSD), do not possess the required spatial resolution due to the large interaction volume between the electrons from the beam and the atoms of the material. Transmission electron microscopy (TEM) has the required spatial resolution. However, due to a lack of automation in the analysis system, the rate of data acquisition is slow which limits the area of the specimen that can be characterized. This paper presents a new characterization technique, Transmission Kikuchi Diffraction (TKD), which enables the analysis of the microstructure of UFG and nanocrystalline materials using an SEM equipped with a standard EBSD system. The spatial resolution of this technique can reach 2 nm. This technique can be applied to a large range of materials that would be difficult to analyze using traditional EBSD. After presenting the experimental set up and describing the different steps necessary to realize a TKD analysis, examples of its use on metal alloys and minerals are shown to illustrate the resolution of the technique and its flexibility in term of material to be characterized.

This paper provides a detailed method to characterize the microstructure of ultra-fine grained and nanocrystalline materials using a scanning electron microscope equipped with a standard electron backscatter diffraction system. Metal alloys and minerals presenting refined microstructures are analyzed using this technique, showing the diversity of its possible applications.

One of the challenges in microstructure analysis nowadays resides in the reliable and accurate characterization of ultra-fine grained (UFG) and ...

Given their potential for significant property improvements relative to their large grained counterparts, much work has been devoted to the continued development of nanocrystalline metals. Despite these efforts, the transition of these materials from the lab bench to actual applications has been blocked by the inability to produce large scale parts that retain the desired nanocrystalline microstructures. Following the development of a method proven to stabilize the nanosized grain structure to temperatures approaching that of the melting point for the given metal, the US Army Research Laboratory (ARL) has progressed to the next stage in the development of these materials - namely the production of large scale parts suitable for testing and evaluation in a range of relevant test environments. This report provides a broad overview of the ongoing efforts in the processing, characterization, and consolidation of these materials at ARL. In particular, focus is placed on the methodology used for producing the nanocrystalline metal powders, in both small and large-scale amounts, that are at the center of ongoing research efforts.

This paper provides a brief overview of the ongoing efforts at the Army Research Laboratory on the processing of bulk nanocrystalline metals with an emphasis on the methodologies used for the production of the novel metal powders.

Given their potential for significant property improvements relative to their large grained counterparts, much work has been devoted to the continued ...

Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys

The increasing complexity and severity of service conditions in areas, such as aerospace and marine industries, nuclear systems, microelectronics, batteries, and biomedical devices, etc., impose great challenges on the reliable performance of alloys exposed to extreme conditions where mechanical and electrochemical attack co-exist. Finding ways for alloys to mitigate the combined attack of wear and corrosion (i.e., tribocorrosion) under such extreme conditions is thus highly critical for improving their reliability and service lifetime when used in such conditions. The challenge lies in the fact that wear and corrosion are not independent of each other, but rather work synergistically to accelerate the total material loss. Thus, a reliable method to evaluate the tribocorrosion resistance of metals and alloys is needed. Here, a protocol for measuring the tribocorrosion rate and wear-corrosion synergy of Al-based bulk and thin film samples in a corrosive environment under room temperature is presented.

Here, we present a protocol to measure the tribocorrosion rate and wear-corrosion synergy of thin film and bulk Al alloys in simulated sea water at room temperature.