The protocols reported in this manuscript were made possible by the accumulated contributions of previous fellows of Dr. Warren Zapol&#39;s laboratory of Anesthesia Research in Critical Care, Department of Anesthesia at Massachusetts General Hospital. We acknowledge the contribution of Drs. Akito Nakagawa, Francesco Zadek, Emanuele Vassena, Chong Lei, Yasuko Nagasaka, Ester Spagnolli and Emanuele Rezoagli.

The procedures indicated in this protocol are in accordance with the review board of Massachusetts General Hospital. The blood samples that were used had been collected during a previous study and were de-identified for the current purpose18.
NOTE: See manufacturer&#39;s instructions for specific guidance regarding optimal connections between tubing and glassware constituting the purge vessel, washing, and general maintenance. Connections need to be firm and carefully m...

Due to the high sensitivity, chemiluminescence-based assays for the determination of NO and related compounds have a high risk of NO2- contamination. Each reagent (especially the NO2- blocking solution) and dilutant (including ddH2O) used in the experiment should be tested for its NO2- content to correct for background signal. Nitrite is extremely reactive with a half-life in whole blood around 10 min and rapidly generates NO3-</...

Since Salvador Moncada and Nobel laureates Robert Furchgott, Louis Ignarro, and Ferid Murad identified nitric oxide (NO) as the previously known endothelial-derived relaxation factor (EDRF), the central role of NO has been established in several key mechanisms spanning throughout vascular biology, neurosciences, metabolism, and host response1,2,3,4,5,6,7. Exogenous administration of NO gas has become an established treatment for respiratory failure due to pulmonary hypertension in the newborn8. Nitric oxide gas has also been investigated for treatment of respiratory syncytial virus (RSV) infection, malaria and other infective diseases, ischemia-reperfusion injury, and for prevention of acute kidney injury in patients undergoing cardiac surgery9,10,11,12. The need for precise measurement techniques to assess the levels of NO, its metabolites, and those of its target proteins and compounds arises from both mechanistic and interventional studies.
Due to its high reactivity, NO may undergo different reactions depending on the biological matrix in which it is produced and/or released. In the absence of hemoglobin (Hb) or other oxy-hemoproteins, NO is oxidized almost completely to nitrite (NO2-).
2NO + O2 &#8594; 2NO2
NO2 + NO&#160;&#8594; N2O3
N2O3 + H2O&#160;&#8594; NO2-&#160;+ H+
NO first undergoes autoxidation with molecular oxygen (O2) to yield nitrogen dioxide (NO2) and reacts with NO2 itself to generate dinitrogen trioxide (N2O3). One molecule of N2O3 reacts with water (H2O) to form two molecules of NO2- and a proton (H+)13. Within whole blood14,15, NO and NO2- are rapidly converted to nitrate (NO3-) as these molecules react avidly with the oxidized heme groups of Hb [Hb-Fe2+-O2 or oxyhemoglobin (oxyHb)] to yield NO3-. This reaction is coupled with the transition of the heme group to the ferric state [Hb-Fe3+ or methemoglobin (metHb)]:
Hb-Fe2+-O2 + NO&#160;&#8594; Hb-Fe3+ + NO3-
The red blood cell (RBC) barrier and the space immediately adjacent to the endothelium are the main factors limiting this reaction and allowing a small portion of the NO released by the endothelium to act as EDRF16,17. In fact, cell-free Hb in the circulation is known to disrupt vasodilation in experimental and clinical settings17,18. Within the RBC, depending on oxygenation and NO2- concentration, a portion of NO reacts with deoxyhemoglobin (Hb-Fe2+) to form iron-nitrosyl Hb (Hb-Fe2+-NO or HbNO):
Hb-Fe2+ + NO&#160;&#8594; Hb-Fe2+-NO
In the RBC15,17, NO2- can form Hb-Fe3+ by reducing Hb-Fe2+ leading to the release of NO, which in turn binds Hb-Fe2+-O2 (preferentially) or Hb-Fe2+.
The generation of NO-derivatives should not be considered strictly unidirectional as NO can be regenerated from NO2-&#160;and NO3- in various tissues and by different enzymes (e.g., by intestinal bacteria or within mitochondria, particularly under hypoxic conditions)19,20.
A variable amount of NO produced (or administered) leads to the downstream generation of S-nitrosothiols, mainly by thiol transnitrosation from N2O3 in the presence of a nucleophile creating a NO+ donor intermediate (Nuc-NO+-NO2-):
N2O3 + RS- &#8594; RS-NO + NO2-
Another possibility for S-nitrosothiols generation is nitrosylation of oxidized thiols (NO reacting with an oxidized thiol):
RS&#8226; + NO&#160;&#8594; RS-NO
This mechanism and direct thiol oxidation by NO2 might be possible only in very specific conditions which are described elsewhere21. S-nitrosothiols range from light molecules like S-nitrosoglutathione to large thiol-containing proteins. S-nitrosohemoglobin (S-NO-Hb) is formed by nitrosation of a thiol group of a conserved cysteine residue in the &#946;-chain (&#946;93C)22.
The generation and metabolism of S-nitrosothiols are part of important regulatory mechanisms. Examples include regulation of glutathione, caspases, N-methyl-D-Aspartate (NMDA), and ryanodine receptors23,24,25,26,27,28. Previously considered as a major mediator of NO biology in vivo, nitrosated albumin (S-nitroso-albumin) seems to be a NO/NO+ transporter without any specific additional biological activity29.
When measuring the concentration of NO and its derivatives from a specific biological sample within a biological matrix, it is important to consider characteristics such as acidity, oxygenation, temperature, and the presence of reagents. Examples include administered exogenous NO donors and, in the setting of acute inflammation, hydrogen peroxide (H2O2) reacting with NO2 leading to generation of supernormal concentration of free radicals like peroxynitrite (ONOO-)21. In addition to the analytical method that is employed, the preanalytical phase of sample preparation and storage is fundamental. Downstream reactions that do not represent the in vivo NO activity shall be predicted, considered, and blocked. A valid example is the instability of S-NO-Hb, requiring a dedicated treatment of blood samples when it is targeted for measurement22.
Chemiluminescence-based assays are the gold standard for detecting the levels of NO and its main metabolites [NO2-, NO3-, S-NO and iron-nitrosyl complexes (Fe-NO)] in any biological fluid, including tissue homogenates30,31. These methods rely upon the chemiluminescence detector (CLD), a device that houses the reaction of NO with ozone (O3), generating NO2 in an excited state (NO2&#8226;). Relaxation of NO2&#8226; causes emission of a photon of light that is detected by a photomultiplier tube, generating an electric signal that is directly proportional to the NO content of the sampled gas mixture32. A simplified schematic of the CLD is represented.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/63107/63107fig01.jpg" /> 
Figure 1: Simplified schematic of a chemiluminescence detector for nitric oxide gas. Chemiluminescence-based detection of nitric oxide (NO) is the stoichiometric generation of one photon per NO gas molecule that is introduced in the chemiluminescence detector (CLD). The chemiluminescence reaction is obtained in a designated chamber supplied with ozone (O3) from an internal generator, which is kept at negative pressure by connection with an external pump, allowing continuous and constant inflow of sample gas. The generation of O3 requires diatomic oxygen (O2) that is supplied by a dedicated O2 tank connected with the CLD (other manufacturers provide CLDs operating with ambient air). Within the reaction chamber, each molecule of NO gas contained in the sampled gas reacts with oxygen to yield one molecule of nitrogen dioxide in the activated state (NO2*). By returning to its ground state, each NO2* molecule emits one photon that is detected by a photomultiplier tube (PMT) located adjacent to the reaction chamber. The PMT with the associated amplifier and central processing unit produces a signal proportional to the photon count and the number of NO molecules in the reaction chamber. <a href="https://www.jove.com/files/ftp_upload/63107/63107fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The sample inlet of the CLD can be connected to a glassware system containing a reaction chamber for liquid samples. The system is continuously purged with an inert gas such as nitrogen, helium, or argon, transferring NO from the reaction chamber to the CLD. Liquid-phase samples are injected through a dedicated membrane into the purge vessel.
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/63107/63107fig02.jpg" /> 
Figure 2: Structure of a purge vessel for chemiluminescence-based detection of nitric oxide gas&#160;The purge vessel (right) allows for the detection of nitric oxide (NO) gas or any other compound that can be readily converted to NO gas when released from a liquid phase reagent. The inert gas inlet is connected to a source (tank) of an inert gas such as Argon, Xeon, or diatomic nitrogen (N2). The needle valve (opens to the left) is used for pressure control within the purge vessel and can be completely removed to clean the vessel. The injection port is covered by a cap with a membrane septum for sample injection. The membrane should be replaced often. A heated jacket surrounds the reaction chamber and is connected to a hot water bath to perform the VCl3 in HCl assay. The purge vessel outlet is connected to the chemiluminescence detector (CLD) or to the NaOH trap (required for VCl3 in HCl assays). To drain the reaction chamber content, first close the stopcocks at the inert gas inlet and the purge vessel outlet, close the needle valve, remove the cap at the injection port and finally open the stopcock at the drain. The NaOH trap (left) is required to be placed inline between the purge vessel and the CLD if the VCl3 in HCl assay is performed because of the corrosivity of HCl. The connection to the CLD always requires an intense field dielectric (IFD) filter to be placed between the CLD and the output of the purge vessel (or the NaOH trap, if used). The IFD filter removes airborne particles and stops liquid from passing through the purge vessel. PTFE = polytetrafluoroethylene. <a href="https://www.jove.com/files/ftp_upload/63107/63107fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
As a consequence, any compound that can be converted to NO through a specific and controlled chemical reaction can be detected with high sensitivity in any biological fluid and tissue homogenate24. Direct measurement of gas-phase NO through chemiluminescence is performed in both experimental and clinical settings. These techniques are extensively described elsewhere33,34,35. Measurement of NO2-, S-nitrosothiols, S-nitrosated proteins, and Fe-NOs can be performed by adding samples in a reaction mixture with triiodide (I3-), which stoichiometrically releases NO gas from all these compounds:
I3- &#8594; I2 + I-
2NO2&#8722; +2I&#8722; +4H+ &#8594; 2NO + I2 +2H2O
I3&#8722; + 2RS-NO &#8594; 3I&#8722; + RSSR + 2NO+
2NO+ + 2I&#8722; &#8594; 2NO + I2
while I3- does not react with NO3-15. Precise measurements of each compound are made possible by pre-treatment of sample aliquots with acidified sulfanilamide (AS) with or without mercuric chloride (HgCl2). Specifically, pre-treatment with AS removes all NO2- content. As a consequence, the NO content measured by the CLD only reflects the sum of S-NOs and Fe-NOs concentration. Injection of HgCl2 in a sample aliquot before AS injection causes NO2- to be released by S-NO. Treatment with AS (leading to NO2- removal) ensures that the measured NO content only reflects the concentration of Fe-NOs. A series of subtractions between the assessments allow to calculate the precise concentration of the three NO derivatives22.
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/63107/63107fig03.jpg" /> 
Figure 3: Steps in sample preparation for the I3- in acetic acid chemiluminescence assay. The sequential steps for preparation of the I3- in acetic acid chemiluminescence assay are illustrated. Use of light-protected centrifuge tubes is required. Tubes 1, 2, and 3 are those used to prepare for the assay. Another sample aliquot (tube 4) is needed for the VCl3 in HCl assay if the measurement of nitrate (NO3-) is required. Steps are indicated by numbers in red. Prefill (Step 1) as indicated with phosphate buffer saline (PBS) or HgCl2 before adding the sample volume. Add the sample volume (2) as indicated, vortex, and incubate for 2 min at room temperature (RT). Add (3) PBS or acidified sulfanilamide (AS) as indicated,vortex, and incubate for 3 min at RT. Run the assay (4). The concentration measured by the assay is the sum of the concentration of the compounds reported under each tube. Tube number 1 will allow measurements of nitrite (NO2-), S-nitrosothiols (S-NO), and iron-nitrosyl complexes (Fe-NOs) as a single signal. For nitrate (NO3-) measurement, samples shall be run with both I3- in acetic acid and VCl3 in HCl assays, and the value obtained from tube 1 should be subtracted from the one obtained from tube 4. *suggested quantities to be used for Hb analysis for determination of residual NO2-, S-nitrosohemoglobin and iron-nitrosyl-hemoglobin. <a href="https://www.jove.com/files/ftp_upload/63107/63107fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
For NO3- measurement, Vanadium (III) chloride (VCl3) in hydrochloric acid (HCl) is used for conversion of NO3- to NO in the purge vessel in order to measure NO3- stoichiometrically with the CLD:
2 NO3-+ 3V+3 + 2H2O&#160;&#8594; 2NO + 3VO2+ + 4H+
To achieve a sufficiently fast conversion, the reaction needs to be performed at 90-95 &#176;C. Reduction from NO3- to NO2- is coupled with reduction of NO2- to NO by HCl. Vanadium metal also reduces S-NOs liberating their NO moiety22,36. The final concentration obtained by CLD with VCl3 in HCl reflects the aggregate concentration of NO3-, NO2, and other nitrosated compounds. Subtraction of the latter value from the concentration yielded with CLD with I3- allows for the calculation of NO3- concentration36,37 (Figure 3).
In the NO consumption assay, the continuous release of NO in the purge vessel by NO donors like (Z)-1-[2-(2-aminoethyl)-N-(2-ammonioethyl)amino]diazen-1-ium-1,2-diolate (DETA-NONOate) generates a stable signal allowing quantifying cell-free oxyHb in the injected samples. The amount of NO consumed in the purge vessel is in a stoichiometric relationship with the amount of oxyHb in the sample38.
Protocols for measurement of NO2-, NO3-, S-nitrosothiols, iron-nitrosyl complexes, and NO consumption by cell-free Hb in plasma samples are illustrated. Studies on NO in the RBC environment require specific sample treatment followed by exclusion chromatography to measure extremely fragile S-NO-Hb and Hb-NO coupled with the determination of total Hb concentration15,22. Sample preparation is instrumental in correcting measurement. Pre-existence of NO2- in H2O and release of NO2- during the assay can lead to measurement of artificially higher concentrations of NO derivatives such as S-NO-Hb14,39. Important aspects of sample preparation are also presented.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Acetic Acid</td>
			<td>Sigma</td>
			<td>45754</td>
			<td>500 mL - liquid</td>
		</tr>
		<tr>
			<td>Antifoam B Emulsion</td>
			<td>Sigma</td>
			<td>A5757</td>
			<td>250 mL - liquid</td>
		</tr>
		<tr>
			<td>DETA NONOate</td>
			<td>Cayman</td>
			<td>82120</td>
			<td>10 mg</td>
		</tr>
		<tr>
			<td>Gibco DPBS (1x) no calcium, no magnesium</td>
			<td>ThermoFisher</td>
			<td>14190144</td>
			<td>500 mL</td>
		</tr>
		<tr>
			<td>Hydroochloric Acid 37% (1 M)</td>
			<td>Sigma</td>
			<td>258148</td>
			<td>500 mL - liquid</td>
		</tr>
		<tr>
			<td>Iodine</td>
			<td>SAFC</td>
			<td>207772</td>
			<td>100 g - solid</td>
		</tr>
		<tr>
			<td>Kimwipes</td>
			<td>Kimtech</td>
			<td>34155</td>
			<td></td>
		</tr>
		<tr>
			<td>Mercury (II) Chloride ACS reagent&#62; 99.5%</td>
			<td>Sigma</td>
			<td>215465</td>
			<td>100 g - solid (dissolve in water)</td>
		</tr>
		<tr>
			<td>Mili-Q Water Purification System</td>
			<td>Millipore</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Model 705 RN 50 &#956;L syringe</td>
			<td>Hamilton</td>
			<td>80530</td>
			<td>Microliter syringe</td>
		</tr>
		<tr>
			<td>Model 802 N 25 &#956;L Syringe</td>
			<td>Hamilton</td>
			<td>84854</td>
			<td>Microliter syringe</td>
		</tr>
		<tr>
			<td>N-ethylmaleimide</td>
			<td>Sigma</td>
			<td>4260</td>
			<td>25 g - crystalline</td>
		</tr>
		<tr>
			<td>Nitric Oxide Analyzer + Bundle Software - Purge Vessel</td>
			<td>Zysense</td>
			<td>NOA 280i</td>
			<td>Chemiluminescence Detector</td>
		</tr>
		<tr>
			<td>Nonidet p-40&#160; (NP-40)</td>
			<td>ThermoFisher</td>
			<td>85125</td>
			<td>10% - 500 mL</td>
		</tr>
		<tr>
			<td>Potassium hexacyanoferrate (III) ACS reagent&#8805; 99%</td>
			<td>Sigma</td>
			<td>244023</td>
			<td>100 g - powder</td>
		</tr>
		<tr>
			<td>Potassium Iodide ACS reagent&#62; 99%</td>
			<td>Sigma</td>
			<td>221945</td>
			<td>100 g - solid</td>
		</tr>
		<tr>
			<td>Potassium Nitrite cryst. For analysis EMSURE ACS</td>
			<td>Supelco</td>
			<td>105067</td>
			<td>250 g - crystalline</td>
		</tr>
		<tr>
			<td>PowerGen 125</td>
			<td>Fisher Scientific</td>
			<td>14-359-251</td>
			<td>Mechanic Homogenizer</td>
		</tr>
		<tr>
			<td>RV3 Two Stage Rotary Vane Pump</td>
			<td>Edwards</td>
			<td>A65201906</td>
			<td>Vacuum Pump - Bundled with analyzer</td>
		</tr>
		<tr>
			<td>Sodium Heparin - BD Hemogard Clo</td>
			<td>BD Biosciences</td>
			<td>BD367871</td>
			<td>75 USP Units</td>
		</tr>
		<tr>
			<td>Sodium hydroxide anhydrous ACS reagent &#8805; 97%</td>
			<td>Sigma</td>
			<td>795429</td>
			<td>1 kg - pelletts</td>
		</tr>
		<tr>
			<td>Sodium Nitrate ACS reagent &#8805; 99%</td>
			<td>Sigma</td>
			<td>221341</td>
			<td>500 g - powder</td>
		</tr>
		<tr>
			<td>Sodium nitrite &#8805; 99%</td>
			<td>Sigma</td>
			<td>S2252</td>
			<td>500 g - crystalline</td>
		</tr>
		<tr>
			<td>Sulfanilamide &#8805; 98%</td>
			<td>Sigma</td>
			<td>S9251</td>
			<td>100 g - solid</td>
		</tr>
		<tr>
			<td>Vanadium (III) Chloride</td>
			<td>Sigma</td>
			<td>112393</td>
			<td>25 g - solid - Caution (exothermic)</td>
		</tr>
		<tr>
			<td>Whatman 1 Filter Paper</td>
			<td>Sigma</td>
			<td>WHA10010155</td>
			<td></td>
		</tr>
	</tbody>
</table>

chemiluminescence-based assays for detection of nitric oxide and its derivatives from autoxidation and nitrosated compounds

Nitric oxide (NO) activity in vivo is the combined results of its direct effects, the action of its derivatives generated from NO autoxidation, and the effects of nitrosated compounds. Measuring NO metabolites is essential to studying NO activity both at vascular levels and in other tissues, especially in the experimental settings where exogenous NO is administered. Ozone-based chemiluminescence assays allow precise measurements of NO and NO metabolites in both fluids (including plasma, tissue homogenates, cell cultures) and gas mixtures (e.g., exhaled breath). NO reacts with ozone to generate nitrogen dioxide in an excited state. The consequent light emission allows photodetection and the generation of an electric signal reflecting the NO content of the sample. Aliquots from the same sample can be used to measure specific NO metabolites, such as nitrate, nitrite, S-nitrosothiols, and iron-nitrosyl complexes. In addition, NO consumed by cell-free hemoglobin is also quantified with chemiluminescence analysis. An illustration of all these techniques is provided.

The NO-consumption by cell-free Hb assay was used in samples containing known concentrations of cell-free oxyHb (Figure 4). As one heme of oxyHb stoichiometrically releases one NO molecule in the assay, purified cell-free oxyHb is used to build the calibration curve for the assay (Supplemental Figure 3).
The dose-response relationship between cell-free Hb (measured with a colorimetric assay) and NO consumption in patients coming off cardiopulmonar...

Watch this Scientific Journal Video about Chemiluminescence-based Assays for Detection of Nitric Oxide and its Derivatives from Autoxidation and Nitrosated Compounds at JoVE.com

Chemiluminescence-based Assays for Detection of Nitric Oxide and its Derivatives from Autoxidation and Nitrosated Compounds

Here, we present protocols for detecting nitric oxide and its biologically relevant derivatives using chemiluminescence-based assays with high sensitivity.

Nitric oxide (NO) activity in vivo is the combined results of its direct effects, the action of its derivatives generated from NO autoxidation, and the ...

This protocol enables researchers to proficiently use a chemiluminescence detector for the measurement of nitric oxide metabolites without the guidance or expense of employing dedicated personnel on site. Chemiluminescence-based assay is the most sensitive method to detect minimal changes in the levels of nitric oxide and its metabolites in any given biological sample. Inhaled nitric oxide is a therapeutic gas used for a wide variety of diseases.It is crucial that disease progression and recovery be accurately correlated with nitric oxide metabolite levels. Inhaled nitric oxide, an antimicrobial, shows promise in treating patients with airway infectious diseases. The chemiluminescence method provides insight into correlating nitric oxide dose and its metabolites with microbiological and pathophysiologic changes.To prepare the DETA-NONOate solution, add 10 milligrams of DETA-NONOate to 610 microliters of 10-millimolar sodium hydroxide in PBS of pH 7.4 to generate 100 millimolar of DETA-NONOate and keep it on ice. To proceed, connect the oxygen line to the chemiluminescence detector and open the oxygen tank at a pressure according to the manufacturer's instruction provided in the text. Then, connect the intense-field dielectric filter line to the chemiluminescence detector.On the chemiluminescence detector interface, start running the detection program for liquid phase assays, ensuring that the oxygen supply is adequate and the detector will start sampling, indicating detection by signal in millivolts, otherwise prompt a negative diagnostic signal. To prepare the purge vessel, close the purge vessel on all three ports by fully screwing the needle valve to the right and closing the inlet and outlet stop cocks. Remove the cap from the purge vessel.Add a sufficient quantity of the reagent specific to the planned assay to the reaction chamber so that the syringe needle used to inject the samples can reach the fluid column while verifying the presence of a stable, desired baseline. To start the purge gas flow, ensure that the inert gas tank is equipped with a two-stage regulator, and connect the inert gas tank with the gas inlet of the vessel. Then, open the outlet of the purge vessel and open the gas with an outlet pressure at the regulator of one to five pounds per square inch.Then, open the inlet of the purge vessel and slowly open the needle valve of the purge vessel to allow inflow of gas and verify bubbling within the purge vessel. To adjust the gas flow, record the cell pressure measured by the chemiluminescence detector with the intense-field dielectric filter line sampling ambient air. Reposition the cap on the purge vessel and connect the intense-field dielectric filter line to the purge vessel.Use the needle valve to reach the same cell pressure at the chemiluminescence detector level that is recorded in ambient air. To start the chemiluminescence signal acquisition program, connect the serial port of the chemiluminescence detector to the computer's serial port into which the acquisition program has been installed. Then, run the analysis program.Click on Acquire, then select the folder to save the data file, type in the file name, and click on Save. While preparing for sample injection, adjust the voltage scale on the screen to have control over the targeted baseline by clicking on the minimum and/or maximum buttons, and then entering the desired value. To perform the sample injection, rinse the syringe at least twice or more with deionized and distilled water before withdrawing each sample, and ensure an unobstructed water ejection on a task wipe.Then, insert the syringe in the sample tube while holding both the syringe and the tube at a close distance and pull up the plunger to the desired volume while ensuring no air bubble or non-homogenized solid parts are trapped. Clean the tip of the syringe with a task wiper and insert the syringe into the setter cap at the injection port. After verifying that the tip of the syringe is within the liquid phase, inject the sample into the reaction chamber.To mark the injection in the software program, type the sample name by clicking the gray box under Sample Names, then click on Mark Injection while verifying that the injection causes an upwards change in the signal or downwards in the nitric oxide consumption by cell-free hemoglobin assay. The dose response relationship between cell-free hemoglobin and nitric oxide consumption was measured through chemiluminescence after cardiopulmonary bypass. It can be assumed that there is a high concentration of heme groups in the oxidized status scavenging nitric oxide.In patients receiving nitric oxide during cardiopulmonary bypass, instead, the majority of heme groups is reduced and does not consume nitric oxide. Measurements of cell-free hemoglobin concentration indicated a slow elimination from plasma within 12 hours after cardiopulmonary bypass. However, nitric oxide consumption peaked at 15 minutes and did not reflect the elimination of cell-free hemoglobin.The linear regression curves of nitric oxide consumption by cell-free hemoglobin exhibited a prevalence of oxidized-and nitric oxide-consuming hemoglobin at 15 minutes, as opposed to more reduced hemoglobin at baseline 4 hours and 12 hours post-cardiopulmonary bypass. The effects of nitric oxide gas administration on nitric oxide consumption were monitored. When patients were treated with nitric oxide gas intra-and post-operatively, the observed increase of free hemoglobin after the cardiopulmonary bypass was not coupled with any increase in nitric oxide consumption.The results indicated that exogenously administered nitric oxide reduced most of the free hemoglobin and prevented nitric oxide scavenging. The experiment is valid only if all conditions remain the same. If the height of the liquid level exceeds the reaction column, we must stop and conduct a new calibration.

chemiluminescence-based-assays-for-detection-nitric-oxide-its

Research

JoVE Journal

Medicine

3.5K ビュー.  Massachusetts General Hospital. このプロトコルにより、研究者は、現場で専任の人員を雇うという指導や費用をかけずに、一酸化窒素代謝産物の測定に化学発光検出器を巧みに使用することができます。化学発光ベースのアッセイは、任意の生物学的サンプル中の一酸化窒素およびその代謝産物のレベルにおける最小限の変化を検出するための最も敏感な方法である。吸入一酸化窒素は、多種多様な?...

ビデオ: Chemiluminescence-based Assays for Detection of Nitric Oxide and its Derivatives from Autoxidation and Nitrosated Compounds

Here, we present protocols for detecting nitric oxide and its biologically relevant derivatives using chemiluminescence-based assays with high sensitivity.

measuring nitrite and nitrate, metabolites in the nitric oxide pathway, in biological materials using the chemiluminescence method

Measuring Nitrite and Nitrate, Metabolites in the Nitric Oxide Pathway, in Biological Materials using the Chemiluminescence Method

Nitric oxide (NO) is an important signaling molecule in vascular homeostasis. NO production in vivo is too low for direct measurement. Chemiluminescence provides useful insight into NO cycle via measuring its precursors and oxidation products, nitrite and nitrate. Nitrite / nitrate determination in body tissues and fluids is...

platelet-based detection of nitric oxide in blood by measuring vasp phosphorylation

Platelet-based Detection of Nitric Oxide in Blood by Measuring VASP Phosphorylation

Here, we present a protocol to address the potential use of platelets as a highly sensitive nitric oxide sensor in blood. It describes initial platelet preparation and the use of nitrite and deoxygenated red blood cells as nitric oxide...

en face detection of nitric oxide and superoxide in endothelial layer of intact arteries

En Face Detection of Nitric Oxide and Superoxide in Endothelial Layer of Intact Arteries

In this article we describe an adapted relatively easy method using the fluorescence dye diaminofluorescein-2 diacetate (DAF-2DA) and dihydroethidium (DHE) for en face simultaneous detection and visualization of intracellular nitric oxide (NO) and superoxide anion (O2.&#8722;) respectively, in freshly isolated intact aortas of an obesity mouse...

En Face Detection of Nitric Oxide and Superoxide in Endothelial Layer of Intact Arteries

analytical techniques for assaying nitric oxide bioactivity

Analytical Techniques for Assaying Nitric Oxide Bioactivity

The endogenous production of nitric oxide (NO) regulates a wide variety of biological functions.  It is becoming increasingly clear that disruption or dysregulation of NO based signaling is involved in many human diseases.  Methods to quantify relevant NO metabolites may provide novel diagnostic or prognostic biomarkers for human...

detection of nitric oxide and superoxide radical anion by electron paramagnetic resonance spectroscopy from cells using spin traps

Detection of Nitric Oxide and Superoxide Radical Anion by Electron Paramagnetic Resonance Spectroscopy from Cells using Spin Traps

Electron paramagnetic resonance (EPR) spectroscopy was employed to detect nitric oxide from bovine aortic endothelial cells and superoxide radical anion from human neutrophils using iron (II)-N-methyl-D-glucamine dithiocarbamate, Fe(MGD)2 and 5,5-dimethyl-1-pyroroline-N-oxide, DMPO,...

procedures of laboratory fumigation for pest control with nitric oxide gas

Procedures of Laboratory Fumigation for Pest Control with Nitric Oxide Gas

This paper describes nitric oxide (NO) fumigation protocols for postharvest pest control. Fumigation chambers are flushed with nitrogen (N2) to establish ultralow oxygen conditions before NO is injected. At the end, chambers are flushed with N2 to dilute NO before exposing products to ambient air to prevent exposure to NO2.

southern blotting, hybridization, and chemiluminescence detection of genomic dna isolated from a2780 cells

Southern Blotting, Hybridization, and Chemiluminescence Detection of Genomic DNA Isolated from A2780 Cells  

early viral entry assays for the identification and evaluation of antiviral compounds

Early Viral Entry Assays for the Identification and Evaluation of Antiviral Compounds

Here, we present a protocol that examines specific steps of the viral entry to identify and evaluate novel antiviral...

novel whole-tissue quantitative assay of nitric oxide levels in drosophila neuroinflammatory response

Novel Whole-tissue Quantitative Assay of Nitric Oxide Levels in Drosophila Neuroinflammatory Response

Levels of the inflammatory cell-signaling molecule nitric oxide (NO) are commonly assayed using Griess reagent. In this protocol, we have created a modified Griess assay utilizing live Drosophila brain tissue in order to detect the secretion of NO in a simple, quantifiable and highly repeatable...

Novel Whole-tissue Quantitative Assay of Nitric Oxide Levels in Drosophila Neuroinflammatory Response

development and characterization of in vitro microvessel network and quantitative measurements of endothelial [ca2+]i and nitric oxide production

Development and Characterization of In Vitro Microvessel Network and Quantitative Measurements of Endothelial [Ca2+]i and Nitric Oxide Production

Primary human umbilical vein endothelial cells (HUVECs) were grown to confluence within a microfluidic network device. The endothelial cell junction and F-actin distributions were illustrated and the changes in intracellular calcium concentration and nitric oxide production in response to adenosine triphosphate (ATP) were quantified in real-time at individual cell...

Development and Characterization of In Vitro Microvessel Network and Quantitative Measurements of Endothelial [Ca2+]i and Nitric Oxide Production

qualitative and quantitative assays for detection and characterization of protein antimicrobials

Qualitative and Quantitative Assays for Detection and Characterization of Protein Antimicrobials

Here, we present protocols to rapidly screen and characterize enzymes for antimicrobial activity. The microslide diffusion assay and the dye-release assay utilize target bacterial substrates for qualitative and quantitative enzymatic activity...

synthesis, characterization, and application of superparamagnetic iron oxide nanoprobes for extrapulmonary tuberculosis detection

Synthesis, Characterization, and Application of Superparamagnetic Iron Oxide Nanoprobes for Extrapulmonary Tuberculosis Detection

To improve serological diagnostic tests for Mycobacterium tuberculosis antigens, we developed superparamagnetic iron oxide nanoprobes to detect extrapulmonary...

application of genetically encoded fluorescent nitric oxide (no&#8226;) probes, the genops, for real-time imaging of no&#8226; signals in single cells

Application of Genetically Encoded Fluorescent Nitric Oxide (NO&amp;#8226;) Probes, the geNOps, for Real-time Imaging of NO&amp;#8226; Signals in Single Cells

This manuscript presents protocols for the application of novel genetically encoded nitric oxide (NO&#8226;) probes (geNOps) to monitor single cell NO&#8226; fluctuations in real-time using fluorescence microscopy. The Ca2+-triggered NO&#8226; formation on the level of individual endothelial cells was visualized by combining geNOps with a chemical Ca2+...

Application of Genetically Encoded Fluorescent Nitric Oxide (NO&#8226;) Probes, the geNOps, for Real-time Imaging of NO&#8226; Signals in Single Cells

polymerase chain reaction and dot-blot hybridization for leptospira detection in water samples

Author Spotlight: &lt;i&gt;Leptospira&lt;/i&gt; DNA Detection in Water for Environmental Analysis and Disease Surveillance

In this study, a dot-blot application was designed to detect Leptospira from the three main clades in water samples. This method allows for the identification of minimal DNA quantities specifically targeted by a digoxigenin-labeled probe, easily detected by an anti-digoxigenin antibody. This approach is a valuable and satisfactory tool for screening...

Dot-Blot Assay for Detection of &lt;i&gt;Leptospira&lt;/i&gt; DNA in Water Samples

https://cloudfront.jove.com/CDNSource/teasers/65435_b.jpg

two-photon imaging of intracellular ca2+ handling and nitric oxide production in endothelial and smooth muscle cells of an isolated rat aorta

Two-photon Imaging of Intracellular Ca2+ Handling and Nitric Oxide Production in Endothelial and Smooth Muscle Cells of an Isolated Rat Aorta

Vascular cell functiondepends on activity of intracellular messengers.  Described here is an ex vivo two photon imaging method that allows the measurement of intracellular calcium and nitric oxide levels in response to physiological and pharmacological stimuli in individual endothelial and smooth muscle cells of an isolated aorta.

Two-photon Imaging of Intracellular Ca2+ Handling and Nitric Oxide Production in Endothelial and Smooth Muscle Cells of an Isolated Rat Aorta

removal of trace elements by cupric oxide nanoparticles from uranium in situ recovery bleed water and its effect on cell viability

Removal of Trace Elements by Cupric Oxide Nanoparticles from Uranium In Situ Recovery Bleed Water and Its Effect on Cell Viability

Production bleed water (PBW) was treated with cupric oxide nanoparticles (CuO-NPs) and cellular toxicity was assessed in cultured human cells. The goal of this protocol was to integrate the native environmental sample into a cell culture format assessing the changes in toxicity due to CuO-NP...

Removal of Trace Elements by Cupric Oxide Nanoparticles from Uranium In Situ Recovery Bleed Water and Its Effect on Cell Viability

development of a lateral flow immunochromatographic strip for rapid and quantitative detection of small molecule compounds

Development of a Lateral Flow Immunochromatographic Strip for Rapid and Quantitative Detection of Small Molecule Compounds

Membrane-based lateral flow immunochromatographic strips (ICSs) are useful tools for low-cost self-diagnosis and have been efficiently applied to toxin, ...

a novel technique for generating and observing chemiluminescence in a biological setting

A Novel Technique for Generating and Observing Chemiluminescence in a Biological Setting

This protocol describes a new intraoperative imaging technique that uses a ruthenium complex as a source of chemiluminescent light emission, thereby producing high signal-to-noise ratios during in vivo imaging. Intraoperative imaging is an expanding field that could revolutionize the way that surgical procedures are...

microwave-assisted extraction of phenolic compounds and antioxidants for cosmetic applications using polyol-based technology

Author Spotlight: Eco-Friendly Extraction of Bioactive Compounds Using Polyol-Based Microwave-Assisted Techniques

This protocol details the utilization of a polyol-based microwave-assisted extraction method for extracting phenolic compounds and natural antioxidants, representing a practical and environmentally sustainable approach to the development of ready-to-use...

Microwave-Assisted Extraction of Phenolic Compounds and Antioxidants for Cosmetic Applications Using Polyol-Based Technology

Production and Detection of Reactive Oxygen Species (ROS) in Cancers

Reactive oxygen species include a number of molecules that damage DNA and RNA and oxidize proteins and lipids (lipid peroxydation). These reactive molecules contain an oxygen and include H2O2 (hydrogen peroxide), NO (nitric oxide), O2- (oxide anion), peroxynitrite (ONOO-), hydrochlorous acid (HOCl), and hydroxyl radical (OH-).
Oxidative species are produced not only under pathological situations (cancers, ischemic/reperfusion, neurologic and cardiovascular pathologies, infectious diseases, inflammatory diseases 1, autoimmune diseases 2, etc&hellip;) but also during physiological (non-pathological) situations such as cellular metabolism 3, 4. Indeed, ROS play important roles in many cellular signaling pathways (proliferation, cell activation 5, 6, migration 7 etc..). ROS can be detrimental (it is then referred to as "oxidative and nitrosative stress") when produced in high amounts in the intracellular compartments and cells generally respond to ROS by upregulating antioxidants such as superoxide dismutase (SOD) and catalase (CAT), glutathione peroxidase (GPx) and glutathione (GSH) that protects them by converting dangerous free radicals to harmless molecules (i.e. water). Vitamins C and E have also been described as ROS scavengers (antioxidants).
Free radicals are beneficial in low amounts 3. Macrophage and neutrophils-mediated immune responses involve the production and release of NO, which inhibits viruses, pathogens and tumor proliferation 8. NO also reacts with other ROS and thus, also has a role as a detoxifier (ROS scavenger). Finally NO acts on vessels to regulate blood flow which is important for the adaptation of muscle to prolonged exercise 9, 10. Several publications have also demonstrated that ROS are involved in insulin sensitivity 11, 12.
Numerous methods to evaluate ROS production are available. In this article we propose several simple, fast, and affordable assays; these assays have been validated by many publications and are routinely used to detect ROS or its effects in mammalian cells. While some of these assays detect multiple ROS, others detect only a single ROS.

Production and Detection of Reactive Oxygen Species ROS in Cancers

Here we propose simple methods to test and evaluate the presence of reactive oxygen species in cells.

Reactive oxygen species include a number of molecules that damage DNA and RNA and oxidize proteins and lipids (lipid peroxydation). These reactive ...

Nitric oxide (NO) is a diatomic free radical that is extremely short lived in biological systems (less than 1 second in circulating blood)1. NO may be considered one of the most important signaling molecules produced in our body, regulating essential functions including but not limited to regulation of blood pressure, immune response and neural communication. Therefore its accurate detection and quantification in biological matrices is critical to understanding the role of NO in health and disease. With such a short physiological half life of NO, alternative strategies for the detection of reaction products of NO biochemistry have been developed. The quantification of relevant NO metabolites in multiple biological compartments provides valuable information with regards to in vivo NO production, bioavailability and metabolism. Simply sampling a single compartment such as blood or plasma may not always provide an accurate assessment of whole body NO status, particularly in tissues. The ability to compare blood with select tissues in experimental animals will help bridge the gap between basic science and clinical medicine as far as diagnostic and prognostic utility of NO biomarkers in health and disease. Therefore, extrapolation of plasma or blood NO status to specific tissues of interest is no longer a valid approach. As a result, methods continue to be developed and validated which allow the detection and quantification of NO and NO-related products/metabolites in multiple compartments of experimental animals in vivo. The established paradigm of NO biochemistry from production by NO synthases to activation of soluble guanylyl cyclase (sGC) to eventual oxidation to nitrite (NO2-) and nitrate (NO3-) may only represent part of NO's effects in vivo. The interaction of NO and NO-derived metabolites with protein thiols, secondary amines, and metals to form S-nitrosothiols (RSNOs), N-nitrosamines (RNNOs), and nitrosyl-heme respectively represent cGMP-independent effects of NO and are likely just as important physiologically as activation of sGC by NO. A true understanding of NO in physiology is derived from in vivo experiments sampling multiple compartments simultaneously. Nitric oxide (NO) methodology is a complex and often confusing science and the focus of many debates and discussion concerning NO biochemistry. The elucidation of new mechanisms and signaling pathways involving NO hinges on our ability to specifically, selectively and sensitively detect and quantify NO and all relevant NO products and metabolites in complex biological matrices. Here, we present a method for the rapid and sensitive analysis of nitrite and nitrate by HPLC as well as detection of free NO in biological samples using in vitro ozone based chemiluminescence with chemical derivitazation to determine molecular source of NO as well as ex vivo with organ bath myography.

The endogenous production of nitric oxide (NO) regulates a wide variety of biological functions. It is becoming increasingly clear that disruption or dysregulation of NO based signaling is involved in many human diseases. Methods to quantify relevant NO metabolites may provide novel diagnostic or prognostic biomarkers for human disease.

Nitric oxide (NO) is a diatomic free radical that is extremely short lived in biological systems (less than 1 second in circulating blood)1. NO may be ...

Cerenkov Luminescence Imaging (CLI) for Cancer Therapy Monitoring

In molecular imaging, positron emission tomography (PET) and optical imaging (OI) are two of the most important and thus most widely used modalities1-3. PET is characterized by its excellent sensitivity and quantification ability while OI is notable for non-radiation, relative low cost, short scanning time, high throughput, and wide availability to basic researchers. However, both modalities have their shortcomings as well. PET suffers from poor spatial resolution and high cost, while OI is mostly limited to preclinical applications because of its limited tissue penetration along with prominent scattering optical signals through the thickness of living tissues.
 Recently a bridge between PET and OI has emerged with the discovery of Cerenkov Luminescence Imaging (CLI)4-6. CLI is a new imaging modality that harnesses Cerenkov Radiation (CR) to image radionuclides with OI instruments. Russian Nobel laureate Alekseyevich Cerenkov and his colleagues originally discovered CR in 1934. It is a form of electromagnetic radiation emitted when a charged particle travels at a superluminal speed in a dielectric medium7,8. The charged particle, whether positron or electron, perturbs the electromagnetic field of the medium by displacing the electrons in its atoms. After passing of the disruption photons are emitted as the displaced electrons return to the ground state. For instance, one 18F decay was estimated to produce an average of 3 photons in water5. 
 Since its emergence, CLI has been investigated for its use in a variety of preclinical applications including in vivo tumor imaging, reporter gene imaging, radiotracer development, multimodality imaging, among others4,5,9,10,11. The most important reason why CLI has enjoyed much success so far is that this new technology takes advantage of the low cost and wide availability of OI to image radionuclides, which used to be imaged only by more expensive and less available nuclear imaging modalities such as PET.
 Here, we present the method of using CLI to monitor cancer drug therapy. Our group has recently investigated this new application and validated its feasibility by a proof-of-concept study12. We demonstrated that CLI and PET exhibited excellent correlations across different tumor xenografts and imaging probes. This is consistent with the overarching principle of CR that CLI essentially visualizes the same radionuclides as PET. We selected Bevacizumab (Avastin; Genentech/Roche) as our therapeutic agent because it is a well-known angiogenesis inhibitor13,14. Maturation of this technology in the near future can be envisioned to have a significant impact on preclinical drug development, screening, as well as therapy monitoring of patients receiving treatments.

Cerenkov Luminescence Imaging CLI for Cancer Therapy Monitoring

Use of Cerenkov Luminescence Imaging (CLI) for monitoring preclinical cancer treatment is described here. This method takes advantage of Cerenkov Radiation (CR) and optical imaging (OI) to visualize radiolabeled probes and thus provides an alternative to PET in preclinical therapeutic monitoring and drug screening.

In  molecular imaging, positron emission tomography (PET) and optical imaging (OI)  are two of the most important and thus most widely used modalities1-3. ...

5/6th Nephrectomy in Combination with High Salt Diet and Nitric Oxide Synthase Inhibition to Induce Chronic Kidney Disease in the Lewis Rat

Chronic kidney disease (CKD) is a global problem. Slowing CKD progression is a major health priority. Since CKD is characterized by complex derangements of homeostasis, integrative animal models are necessary to study development and progression of CKD. To study development of CKD and novel therapeutic interventions in CKD, we use the 5/6th nephrectomy ablation model, a well known experimental model of progressive renal disease, resembling several aspects of human CKD. The gross reduction in renal mass causes progressive glomerular and tubulo-interstitial injury, loss of remnant nephrons and development of systemic and glomerular hypertension. It is also associated with progressive intrarenal capillary loss, inflammation and glomerulosclerosis. Risk factors for CKD invariably impact on endothelial function. To mimic this, we combine removal of 5/6th of renal mass with nitric oxide (NO) depletion and a high salt diet. After arrival and acclimatization, animals receive a NO synthase inhibitor (NG-nitro-L-Arginine) (L-NNA) supplemented to drinking water (20 mg/L) for a period of 4 weeks, followed by right sided uninephrectomy. One week later, a subtotal nephrectomy (SNX) is performed on the left side. After SNX, animals are allowed to recover for two days followed by LNNA in drinking water (20 mg/L) for a further period of 4 weeks. A high salt diet (6%), supplemented in ground chow (see time line Figure 1), is continued throughout the experiment. Progression of renal failure is followed over time by measuring plasma urea, systolic blood pressure and proteinuria. By six weeks after SNX, renal failure has developed. Renal function is measured using 'gold standard' inulin and para-amino hippuric acid (PAH) clearance technology. This model of CKD is characterized by a reduction in glomerular filtration rate (GFR) and effective renal plasma flow (ERPF), hypertension (systolic blood pressure&gt;150 mmHg), proteinuria (&gt; 50 mg/24 hr) and mild uremia (&gt;10 mM). Histological features include tubulo-interstitial damage reflected by inflammation, tubular atrophy and fibrosis and focal glomerulosclerosis leading to massive reduction of healthy glomeruli within the remnant population (&lt;10%). Follow-up until 12 weeks after SNX shows further progression of CKD.

A two-stage method to establish chronic kidney disease (CKD) in the Lewis rat by surgically removing 5/6th of renal mass is described. Combination of the surgical procedure, NOS-inhibition and a high-salt diet leads to a model resembling human CKD, allowing study of causal mechanisms and development of novel therapeutic interventions.

Chronic kidney disease (CKD) is a global problem. Slowing CKD progression is a major health priority. Since CKD is characterized by complex derangements ...

Polyacrylamide Gels for Invadopodia and Traction Force Assays on Cancer Cells

Rigid tumor tissues have been strongly implicated in regulating cancer cell migration and invasion. Invasive migration through cross-linked tissues is facilitated by actin-rich protrusions called invadopodia that proteolytically degrade the extracellular matrix (ECM). Invadopodia activity has been shown to be dependent on ECM rigidity and cancer cell contractile forces suggesting that rigidity signals can regulate these subcellular structures through actomyosin contractility. Invasive and contractile properties of cancer cells can be correlated in vitro using invadopodia and traction force assays based on polyacrylamide gels (PAAs) of different rigidities. Invasive and contractile properties of cancer cells can be correlated in vitro using invadopodia and traction force assays based on polyacrylamide gels (PAAs) of different rigidities. While some variations between the two assays exist, the protocol presented here provides a method for creating PAAs that can be used in both assays and are easily adaptable to the user&#8217;s specific biological and technical needs.

Mechanical rigidity in the tumor microenvironment plays a crucial role in driving malignant behavior by increasing invadopodia activity and actomyosin contractility. Using polyacrylamide gels (PAAs), invadopodia and traction force assays can be utilized to study the invasive and contractile properties of cancer cells in response to matrix rigidity.

Rigid tumor tissues have been strongly implicated in regulating cancer cell migration and invasion. Invasive migration through cross-linked tissues is ...

Boldness, Aggression, and Shoaling Assays for Zebrafish Behavioral Syndromes

A behavioral syndrome exists when specific behaviors interact under different contexts. Zebrafish have been test subjects in recent studies and it is important to standardize protocols to ensure proper analyses and interpretations. In our previous studies, we have measured boldness by monitoring a series of behaviors (time near surface, latency in transitions, number of transitions, and darts) in a 1.5 L trapezoidal tank. Likewise, we quantified aggression by observing bites, lateral displays, darts, and time near an inclined mirror in a rectangular 19 L tank. By dividing a 76 L tank into thirds, we also examined shoaling preferences. The shoaling assay is a highly customizable assay and can be tailored for specific hypotheses. However, protocols for this assay also must be standardized, yet flexible enough for customization. In previous studies, end chambers were either empty, contained 5 or 10 zebrafish, or 5 pearl danios (D. albolineatus). In the following manuscript, we present a detailed protocol and representative data that accompany successful applications of the protocol, which will allow for replication of behavioral syndrome experiments.

This manuscript describes the setup, implementation, and analysis of boldness, aggression, and shoaling in zebrafish and testing for the presence of a behavioral syndrome. A standardized approach for behavioral quantification will allow for easier comparison across studies. Modifications to this protocol are possible as each assay can be run individually.

A behavioral syndrome exists when specific behaviors interact under different contexts. Zebrafish have been test subjects in recent studies and it is ...

A molecular imaging probe comprising superparamagnetic iron oxide (SPIO) nanoparticles and Mycobacterium tuberculosis surface antibody (MtbsAb) was synthesized to enhance imaging sensitivity for extrapulmonary tuberculosis (ETB). An SPIO nanoprobe was synthesized and conjugated with MtbsAb. The purified SPIO-MtbsAb nanoprobe was characterized using TEM and NMR. To determine the targeting ability of the probe, SPIO-MtbsAb nanoprobes were incubated with Mtb for in vitro imaging assays and injected into Mtb-inoculated mice for in vivo investigation with magnetic resonance (MR). The contrast enhancement reduction on magnetic resonance imaging (MRI) of Mtb and THP1 cells showed proportional to the SPIO-MtbsAb nanoprobe concentration. After 30 min of intravenous SPIO-MtbsAb nanoprobe injection into Mtb-infected mice, the signal intensity of the granulomatous site was enhanced by 14-fold in the T2-weighted MR images compared with that in mice receiving PBS injection. The MtbsAb nanoprobes can be used as a novel modality for ETB detection.

To improve serological diagnostic tests for Mycobacterium tuberculosis antigens, we developed superparamagnetic iron oxide nanoprobes to detect extrapulmonary tuberculosis.

A molecular imaging probe comprising superparamagnetic iron oxide (SPIO) nanoparticles and Mycobacterium tuberculosis surface antibody (MtbsAb) was ...

Platelets are the blood components responsible for proper blood clotting. Their function is highly regulated by various pathways. One of the most potent vasoactive agents, nitric oxide (NO), can also act as a powerful inhibitor of platelet aggregation. Direct NO detection in blood is very challenging due to its high reactivity with cell-free hemoglobin that limits NO half-life to the millisecond range. Currently, NO changes after interventions are only estimated based on measured changes of nitrite and nitrate (members of the nitrate-nitrite-NO metabolic pathway). However precise, these measurements are rather difficult to interpret vis a vis actual NO changes, due to the naturally high baseline nitrite and nitrate levels that are several orders of magnitude higher than expected changes of NO itself. Therefore, the development of direct and simple methods that would allow one to detect NO directly is long overdue. This protocol addresses a potential use of platelets as a highly sensitive NO sensor in blood. It describes initial platelet rich plasma (PRP) and washed platelet preparations and the use of nitrite and deoxygenated red blood cells as NO generators. Phosphorylation of VASP at serine 239 (P-VASPSer239) is used to detect the presence of NO. The fact that VASP protein is highly expressed in platelets and that it is rapidly phosphorylated when NO is present leads to a unique opportunity to use this pathway to directly detect NO presence in blood.

Here, we present a protocol to address the potential use of platelets as a highly sensitive nitric oxide sensor in blood. It describes initial platelet preparation and the use of nitrite and deoxygenated red blood cells as nitric oxide generators.

Platelets are the blood components responsible for proper blood clotting. Their function is highly regulated by various pathways. One of the most potent ...

A Novel Inhalation Mask System to Deliver High Concentrations of Nitric Oxide Gas in Spontaneously Breathing Subjects

Nitric Oxide (NO) is administered as gas for inhalation to induce selective pulmonary vasodilation. It is a safe therapy, with few potential risks even if administered at high concentration. Inhaled NO gas is routinely used to increase systemic oxygenation in different disease conditions. The administration of high concentrations of NO also exerts a virucidal effect in vitro. Owing to its favorable pharmacodynamic and safety profiles, the familiarity in its use by critical care providers, and the potential for a direct virucidal effect, NO is clinically used in patients with coronavirus disease-2019 (COVID-19). Nevertheless, no device is currently available to easily administer inhaled NO at concentrations higher than 80 parts per million (ppm) at various inspired oxygen fractions, without the need for dedicated, heavy, and costly equipment. The development of a reliable, safe, inexpensive, lightweight, and ventilator-free solution is crucial, particularly for the early treatment of non-intubated patients outside of the intensive care unit (ICU) and in a limited-resource scenario. To overcome such a barrier, a simple system for the non-invasive NO gas administration up to 250 ppm was developed using standard consumables and a scavenging chamber. The method has been proven safe and reliable in delivering a specified NO concentration while limiting nitrogen dioxide levels. This paper aims to provide clinicians and researchers with the necessary information on how to assemble or adapt such a system for research purposes or clinical use in COVID-19 or other diseases in which NO administration might be beneficial.

This simple and highly adaptable system device for the inhalation of high-concentration nitric oxide (NO) gas does not require mechanical ventilators, positive pressure, or high gas flows. Standard medical consumables and a snug-fitting mask are used to safely deliver NO gas to spontaneously breathing subjects.

Nitric Oxide (NO) is administered as gas for inhalation to induce selective pulmonary vasodilation. It is a safe therapy, with few potential risks even if ...

Visualizing and Quantifying Pharmaceutical Compounds within Skin using Coherent Raman Scattering Imaging

Cutaneous pharmacokinetics (cPK) after topical formulation application has been a research area of particular interest for regulatory and drug development scientists to mechanistically understand topical bioavailability (BA). Semi-invasive techniques, such as tape-stripping, dermal microdialysis, or dermal open-flow microperfusion, all quantify macroscale cPK. While these techniques have provided vast cPK knowledge, the community lacks a mechanistic understanding of active pharmaceutical ingredient (API) penetration and permeation at the cellular level. 
One noninvasive approach to address microscale cPK is coherent Raman scattering imaging (CRI), which selectively targets intrinsic molecular vibrations without the need for extrinsic labels or chemical modification. CRI has two main methods-coherent anti-Stokes Raman scattering (CARS) and stimulated Raman scattering (SRS)-that enable sensitive and selective quantification of APIs or inactive ingredients. CARS is typically utilized to derive structural skin information or visualize chemical contrast. In contrast, the SRS signal, which is linear with molecular concentration, is used to quantify APIs or inactive ingredients within skin stratifications. 
Although mouse tissue has commonly been utilized for cPK with CRI, topical BA and bioequivalence (BE) must ultimately be assessed in human tissue before regulatory approval. This paper presents a methodology to prepare and image ex vivo skin to be used in quantitative pharmacokinetic CRI studies in the evaluation of topical BA and BE. This methodology enables reliable and reproducible API quantification within human and mouse skin over time. The concentrations within lipid-rich and lipid-poor compartments, as well as total API concentration over time are quantified; these are utilized for estimates of micro- and macroscale BA and, potentially, BE.

A coherent Raman scattering imaging methodology to visualize and quantify pharmaceutical compounds within the skin is described. This paper describes skin tissue preparation (human and mouse) and topical formulation application, image acquisition to quantify spatiotemporal concentration profiles, and preliminary pharmacokinetic analysis to assess topical drug delivery.

Cutaneous pharmacokinetics (cPK) after topical formulation application has been a research area of particular interest for regulatory and drug development ...