The author would like to acknowledge the following people. The staff of the University of Maryland Insect Transformation Facility: Channa Aluvihare, Robert Alford, and Daniel Gay. Without their dedicated work, the Insect Transformation Facility would not exist. Vanessa Meldener-Harrell for proofreading this manuscript.

NOTE: The protocol as described below uses the Sutter BV-10 microcapillary beveled. However, this protocol can be modified for use with any model microcapillary beveled.
1. Assembly of regulator, pressure gauge, and air supply tubing
<ol>
	<li>Cut a section of urethane tubing for the connection from the air supply to the base of the regulator (R; Section 1, Figure 1). The length of this section will depend on the distance from the air supply to ...

Protocol for Wet Beveling of Microinjection Needles Under Constant Air Pressure

<ol>
	<li>Rubin, G. M., Spradling, A. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Genetic+transformation+of+Drosophila+with+transposable+Element+Vectors.">Genetic transformation of Drosophila with transposable Element Vectors.</a> Science. 218 (4570), 348-353 (1982).</li><li>O'Brochta, D. A., Atkinson, P. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transformation+systems+in+insects.">Transformation systems in insects.</a> Methods Mol Biol. 260, 227-254 (2004).</li><li>Handler, A. M., James, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Insect Transgenesis: Methods and Applications. , (2000).</li><li>Harrell, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mosquito+embryo+microinjection.">Mosquito embryo microinjection.</a> Cold Spring Harbor Protocols. , (2023).</li><li>Allen, M. L., O'Brochta, D. A., Atkinson, P. W., Levesque, C. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Stable,+germ-line+transformation+of+Culex+Quinquefasciatus+(Diptera:+Culicidae).">Stable, germ-line transformation of Culex Quinquefasciatus (Diptera: Culicidae).</a> J Med Entomol. 38 (5), 701-710 (2001).</li><li>Grossman, G. L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Germline+transformation+of+the+malaria+vector,+Anopheles+gambiae,+with+the+piggyBac+transposable+element.">Germline transformation of the malaria vector, Anopheles gambiae, with the piggyBac transposable element.</a> Insect Mol Biol. 10 (6), 597-604 (2001).</li><li>Adelman, Z. N., Jasinskiene, N., James, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+and+applications+of+transgenesis+in+the+yellow+fever+mosquito,+Aedes+aegypti.">Development and applications of transgenesis in the yellow fever mosquito, Aedes aegypti.</a> Mol Biochem Parasitol. 121 (1), 1-10 (2002).</li><li>Perera, O. P., Harrell, R. A., Handler, A. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Germ-line+transformation+of+the+South+American+malaria+vector,+Anopheles+albimanus,+with+a+piggyBac/EGFP+transposon+vector+is+routine+and+highly+efficient.">Germ-line transformation of the South American malaria vector, Anopheles albimanus, with a piggyBac/EGFP transposon vector is routine and highly efficient.</a> Insect Mol Biol. 11 (4), 291-297 (2002).</li><li>Harrell, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mosquito+embryo+microinjection+under+halocarbon+oil+or+in+aqueous+solution.">Mosquito embryo microinjection under halocarbon oil or in aqueous solution.</a> Cold Spring Harb Protoc. , (2023).</li><li>Louradour, I., Ghosh, K., Inbar, E., Sacks, D. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=CRISPR/Cas9+mutagenesis+in+Phlebotomus+papatasi:+The+immune+deficiency+pathway+impacts+vector+competence+for+Leishmania+major.">CRISPR/Cas9 mutagenesis in Phlebotomus papatasi: The immune deficiency pathway impacts vector competence for Leishmania major.</a> mBio. 10 (4), e01941 (2019).</li><li>Tamura, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Germline+transformation+of+the+silkworm+Bombyx+mori+L.+using+a+piggyBac+transposon-derived+vector.">Germline transformation of the silkworm Bombyx mori L. using a piggyBac transposon-derived vector.</a> Nat Biotechnol. 18 (1), 81-84 (2000).</li><li>. BV-10 Micropipette Beveler Operation Manual Rev. 3.00 Available from: <a target="_blank" href="https://www.manualslib.com/manual/2073788/Sutter-Instrument-Bv-10.html">https://www.manualslib.com/manual/2073788/Sutter-Instrument-Bv-10.html</a> (2018)</li></ol>

Genetic modification of mosquitoes relies on precise microinjection of the modification materials (plasmids, guide RNAs, or proteins) into pre-blastoderm embryos3,4,5,6,7,8. Crucial to this process are sharp needles that easily pierce the embryo during injection2,4. A...

Insect genetic modification is a process originally developed in Drosophila by Rubin and Spradling, and over the years, this process has been modified to create genetic modifications in other species1. The process relies on the precise delivery of modification components microinjected into embryos at a specific window of time and location within the developing embryo2,3,4. Sharp microinjection needles are a critical tool in the process of genetic modification of some insects, such as mosquitoes4,5,6,7,8,9 and sand flies10 while not as critical for other insects, such as silkworms11. Sharp needles are often a key factor between success and failure when trying to create a genetically modified insect2,4. Typically, microcapillary glass needles are pulled by heating glass to the point where the glass becomes elastic, allowing the capillary to be pulled into a tapering closed tip needle. Before the needle can be used, it needs to be opened in a manner that creates a sharp tip for injection. Traditionally, needles are opened by brushing the needle tip gently against something (the edge of a slide/coverslip, or the embryo, etc.) that causes a small amount of glass to break off from the tip, randomly creating a sharp tip2,3. A slightly less random process is dry beveling, where the needle is quickly lowered onto an optically flat, spinning abrasive plate for a short period of time, causing a small amount of glass to be abraded from the needle tip, creating a sharp tip. Dry beveling is a little less random than brushing the needle tip against something. The protocol described below takes the beveling process a step further by supplying compressed air to the needle being beveled and beveling it under a liquid layer so that bubbles are visible as soon as the needle has been opened. This protocol details a method for producing reliably sharp microinjection needles. Beveling under a liquid layer is an improvement over randomly breaking the needle as described above, and dry beveling because the user receives feedback on the beveling process, allowing the person beveling to know when the needle is open and relatively how large the needle opening is. Knowing the relative opening size of the needle tip can allow the person beveling to create needles with different opening sizes. Various needle opening sizes have different advantages; for instance, larger needle opening sizes can accommodate injection mixes of high viscosity, while smaller opening needles cause less damage to the embryo being injected.
Air is supplied to the needle using a regulator and a system of urethane tubing based on a modified air-pressure regulated injection system2. While air is supplied to the needle at a constant pressure, the needle is beveled under a layer of liquid. The beveling process is comprised of a repeated five-step process: 1) lowering the needle to the abrasive surface, 2) allowing the needle to bevel for a short period of time, 3) raising the needle away from the abrasive plate while keeping it beneath the surface of the liquid layer, 4) stopping the spin of the abrasive plate to check for the appearance of bubbles. If no bubbles are present, then steps 1 through 4 are repeated until bubbles appear; 5) Once bubbles are present, the air pressure can be adjusted to determine the relative opening size of the needle. The lower the pressure needed to stop bubble formation, the larger the opening at the needle tip.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>1.0 mm O.D. microcapillaries</td>
			<td>World Precision Instruments</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Beveler pedestal oil</td>
			<td>Sutter Instruments</td>
			<td>008</td>
			<td></td>
		</tr>
		<tr>
			<td>Bicycle fender clip</td>
			<td>VeloOrange</td>
			<td>R-clip 4-pack</td>
			<td>https://velo-orange.com/products/vo-r-clip-4-pack</td>
		</tr>
		<tr>
			<td>Boom Stand Microscope</td>
			<td>AmScope</td>
			<td></td>
			<td>AMScope 3.5X-90X Trinocular LED Boom Stand Stereo Microscope or equivalent</td>
		</tr>
		<tr>
			<td>BV-10 Beveler</td>
			<td>Sutter Instruments</td>
			<td>BV-10</td>
			<td></td>
		</tr>
		<tr>
			<td>Diamond abrasive plate&#160;</td>
			<td>Sutter Instruments</td>
			<td>104F</td>
			<td>Diamond abrasive plate - extra fine (0.2 &#181; to 1.0 &#181; tip sizes)</td>
		</tr>
		<tr>
			<td>Gasket, Buna-N</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>11761-2-pkg</td>
			<td>Used to seal connection on T&#160; or L connectors, if not already included with these pieces</td>
		</tr>
		<tr>
			<td>Hose Clamp</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>5000-2-pkg</td>
			<td></td>
		</tr>
		<tr>
			<td>Hose connector</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>CT4-pkg</td>
			<td>Need 5 hose connectors</td>
		</tr>
		<tr>
			<td>Microinjection Needle Holder</td>
			<td>World Precision Instruments</td>
			<td>MPH3-10</td>
			<td>Needle holder for 1mm outer diameter microcapillaries</td>
		</tr>
		<tr>
			<td>P-2000</td>
			<td>Sutter Instruments</td>
			<td></td>
			<td>Any needle puller</td>
		</tr>
		<tr>
			<td>Photo-Flo 200 Solution</td>
			<td>B&#38;H Photo, Video and Audio</td>
			<td>BH #KOPF200P&#160; MFR #1464510</td>
			<td>wetting agent</td>
		</tr>
		<tr>
			<td>Pressure Gauge</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>PG-100</td>
			<td>0-100 psi gauge</td>
		</tr>
		<tr>
			<td>Reference wick</td>
			<td>Sutter Instruments</td>
			<td>X050300</td>
			<td></td>
		</tr>
		<tr>
			<td>Reference wick holder</td>
			<td>Sutter Instruments</td>
			<td>M100019</td>
			<td></td>
		</tr>
		<tr>
			<td>Regulator</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>01-Mar</td>
			<td>Need #10-32 ports for connections</td>
		</tr>
		<tr>
			<td>Rubber Packing Sheet 6 inx 6 in</td>
			<td>Danco</td>
			<td>Model # 59849</td>
			<td></td>
		</tr>
		<tr>
			<td>T fitting</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>15002-2-pkg</td>
			<td></td>
		</tr>
		<tr>
			<td>Threaded Bar</td>
			<td></td>
			<td></td>
			<td>Either a threaded rod or bar with threaded end. Threads must be 10-32.</td>
		</tr>
		<tr>
			<td>Urethane tubing</td>
			<td>Clippard Instrument Laboratory, Inc.</td>
			<td>URH1-0804-BLT-050</td>
			<td></td>
		</tr>
	</tbody>
</table>

wet beveling of microinjection needles utilizing constant air pressure for feedback on needle opening

Microinjection needles are a critical tool in the delivery of genome modification reagents, CRISPR components (guide RNAs, Cas9 protein, and donor template), and transposon system components (plasmids and transposase mRNA) into developing insect embryos. Sharp microinjection needles are particularly important during the delivery of these modifying agents since they help minimize damage to the embryo being injected, thereby increasing the survival of these embryos as compared to injection with non-beveled needles. Further, the beveling of needles produces needles that are more consistent from needle to needle as compared to needles opened by randomly breaking the needle tip by brushing the tip against an object (side of a coverslip, the surface of the embryo to be injected, etc.). The process of wet beveling of microinjection needles with constant pressure air delivered to the needle allows the person beveling the needle to know when the needle is open (presence of bubbles) and also gives a relative indication of how large a needle opening has been created. The relative opening size in the needle can be determined by adjusting the air pressure delivered to the needle until an equilibrium is reached and bubbles stop flowing from the tip of the needle. The lower the pressure at which the equilibrium is reached, the larger the needle size; and conversely, the higher the pressure, the smaller the needle size.

Author Spotlight: Enhancing Microinjection Needle Quality by Wet Beveling

Wet Beveling of Microinjection Needles Utilizing Constant Air Pressure for Feedback on Needle Opening

The Insect Transformation Facility, we are a university service facility that helps clients make genetically modified insects. Their research ranges from neuroscience in which they are doing research on mosquito olfaction to public health research in which they are making vaccines to malaria, to expressing novel proteins within the black soldier fly. Traditionally, needles have been opened by pulling the needles and then brushing them against something in order to open that needle, and that can produce needles which are either perfect for microinjection or unusable.And so this method allows us to open the needle in a concise fashion in which we get sharp needles each time. This protocol gives feedback on the opening size of the needle. Once that needle is open, you can dial back the pressure that is being delivered to the tip of the needle, and the higher the pressure at which air bubbles stop flowing, the smaller the opening size of that needle.

The procedure described above produces consistently sharp microinjection needles. Sharp needles are characterized by being able to insert into soft chorion insect embryos, such as mosquito embryos, with little to no resistance from the embryo membrane. When mosquito embryos are microinjected for genetic modification, the embryo membrane is relatively elastic. Pushing a dull needle against the embryo membrane will cause it to indent (Figure 4B). When the needle is pulled back, the membrane re...

This protocol describes the assembly of a pneumatic system for the delivery of pressurized air to a needle during the process of needle beveling. The protocol further describes the beveling process for creating sharp microinjection needles and how to gauge the relative opening size of the needle.

Microinjection needles are a critical tool in the delivery of genome modification reagents, CRISPR components (guide RNAs, Cas9 protein, and donor ...

wet-beveling-microinjection-needles-utilizing-constant-air-pressure

Research

JoVE Journal

Biology

114 ビュー.  University of Maryland. 昆虫形質転換施設は、遺伝子組み換え昆虫の作製を支援する大学サービス施設です。彼らの研究は、蚊の嗅覚に関する研究を行う神経科学から、マラリアに対するワクチンを作る公衆衛生研究、そしてハエの新規タンパク質の発現まで多岐にわたります。従来、針は引っ張って何かにブラシをかけ、その針を開くことで開かされてきましたが、?...

ビデオ: 著者スポットライト:ウェットベベルによるマイクロインジェクション針の品質向上

This protocol describes the assembly of a pneumatic system for the delivery of pressurized air to a needle during the process of needle beveling. The protocol further describes the beveling process for creating sharp microinjection needles and how to gauge the relative opening size of the...

https://cloudfront.jove.com/CDNSource/teasers/66767_b.jpg

preparing the grinding assembly for the wet beveling of microinjection needles

Preparing the Grinding Assembly for the Wet Beveling of Microinjection Needles

procedure for the wet beveling of borosilicate microinjection needles under constant delivery of pressurized air

Procedure for the Wet Beveling of Borosilicate Microinjection Needles Under Constant Delivery of Pressurized Air

measuring the mechanical properties of glass fiber reinforcement polymer composite laminates obtained by different fabrication processes

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process 

This paper describes a fabrication process for fiber-reinforced polymer matrix composite laminates obtained using the wet hand lay-up/vacuum bag...

Fabrication and Mechanical Property Assessment of Fiber Composite Laminates

https://cloudfront.jove.com/CDNSource/teasers/65376_b.jpg

embryo microinjection for transgenesis in drosophila

Author Spotlight: Optimizing Embryo Microinjection for Transgenesis in &lt;i&gt;Drosophila&lt;/i&gt;

This article takes the phiC31 integrase-mediated transgenesis in Drosophila as an example and presents an optimized protocol for embryo microinjection,&#160;a crucial step for creating transgenic...

phiC31 Integrase-Mediated Embryo Transgenesis in &lt;i&gt;Drosophila&lt;/i&gt;

https://cloudfront.jove.com/CDNSource/teasers/66679_b.jpg

generating transgenics and knockouts in strongyloides species by microinjection

Generating Transgenics and Knockouts in Strongyloides Species by Microinjection

The functional genomic toolkit for the parasitic nematodes Strongyloides stercoralis and Strongyloides ratti includes transgenesis, CRISPR/Cas9-mediated mutagenesis, and RNAi. This protocol will demonstrate how to use intragonadal microinjection to introduce transgenes and CRISPR components into S.&#160;stercoralis and...

Generating Transgenics and Knockouts in Strongyloides Species by Microinjection

activation of apoptosis by cytoplasmic microinjection of cytochrome c

Activation of Apoptosis by Cytoplasmic Microinjection of Cytochrome c

In this protocol, we describe the direct cytoplasmic microinjection of cytochrome c protein into fibroblasts and primary sympathetic neurons.  This technique allows for the introduction of cytochrome c protein into the cytoplasm of cells and mimics the release of cytochrome c from mitochondria, which occurs during...

Activation of Apoptosis by Cytoplasmic Microinjection of Cytochrome c

operation procedure and precautions of lingnan fire-needle therapy in osteoporosis model rats

Author Spotlight: Exploring the Impact of Lingnan Fire-Needle Therapy in Osteoporosis Intervention

Here, we present a protocol for the application of Lingnan Fire-Needle therapy in the intervention of osteoporosis model...

Osteoporosis Management in Rats Through Lingnan Fire-Needle Therapy

https://cloudfront.jove.com/CDNSource/teasers/65970_b.jpg

custom smartphone application to guide locomotor-respiratory coupling in the field using step-adaptive breathing sounds 

Author Spotlight: Exploring Breathing Techniques and Digital Solutions for Enhancing Running Performance

Locomotor-respiratory coupling (LRC) is potentially advantageous for runners but may be difficult to perform. We introduce a custom solution implemented on a smartphone to individualize and guide runners toward...

Enhancing Running Performance and Comfort Using RunRhythm

https://cloudfront.jove.com/CDNSource/teasers/66733_b.jpg

cryo-electron microscopy screening automation across multiple grids using smart leginon

Author Spotlight: Enhancing Cryo-Electron Microscopy by Automated Data Collection and Analysis Techniques

Cryo-electron microscopy (cryoEM) multi-grid screening is often a tedious process that demands hours of attention. This protocol shows how to set up a standard Leginon collection and Smart Leginon Autoscreen to automate this process. This protocol can be applied to the majority of cryoEM holey foil...

Accelerating Macromolecular Structural Analysis Using Smart Leginon Autoscreen

https://cloudfront.jove.com/CDNSource/teasers/66007_b.jpg

generation of transgenic hydra by embryo microinjection

Generation of Transgenic Hydra by Embryo Microinjection

Stably transgenic Hydra are made by microinjection of plasmid DNA into embryos followed by random genomic integration and asexual propagation to establish a uniform line. Transgenic Hydra are used to track cell movements, overexpress genes, study promoter function, or knock down gene expression using RNAi.

Generation of Transgenic Hydra by Embryo Microinjection

detection of extravascular trypanosoma parasites by fine needle aspiration

Detection of Extravascular Trypanosoma Parasites by Fine Needle Aspiration

Fine Needle Aspiration is a technique, whereby cells are obtained from a lesion or organ using a thin needle. Aspirated material is smeared, stained and examined under a microscope for diagnosis or used for molecular biology, cytometry or in vitro analysis. It is cheap, simple, quick and causes minimal...

Detection of Extravascular Trypanosoma Parasites by Fine Needle Aspiration

microinjection of recombinant rcas(a) retrovirus into embryonic chicken lens

Author Spotlight: Investigating Lens Development and Function Through Microinjection of RCAS(A) Retrovirus in Embryonic Chicken Lens 

This protocol paper describes the methodology of embryonic chicken lens microinjection of an RCAS(A) retrovirus as a tool for studying in situ function and expression of proteins during lens...

Studying Protein Expression During Chicken Lens Development

https://cloudfront.jove.com/CDNSource/teasers/65727_b.jpg

clinical efficacy of small needle knife therapy on stage i-ii frozen shoulder

Author Spotlight: Treating Frozen Shoulder with Small Needle Knife Therapy 

The protocol presented here describes the detailed operation method and proves the effectiveness of a small needle knife in the treatment of frozen...

Therapeutic Efficacy of Small Needle Knife Therapy in Treating Frozen Shoulder

https://cloudfront.jove.com/CDNSource/teasers/65904_b.jpg

systematic endobronchial ultrasound - the six landmarks approach

Author Spotlight: Demonstrating Systematic Endobronchial Ultrasound to New Endoscopists 

Endobronchial ultrasound-guided sampling using transbronchial needle aspiration plays a key role in staging and diagnosing lung cancer. We propose a systematic stepwise approach dividing the procedure into six landmarks that should be taught to new operators.

Simulation-Based Training of EBUS-TBNA

https://cloudfront.jove.com/CDNSource/teasers/65551_b.jpg

analysis of mrna nuclear export kinetics in mammalian cells by microinjection

Analysis of mRNA Nuclear Export Kinetics in Mammalian Cells by Microinjection

Here we describe an assay that employs the power of microinjection coupled with fluorescent in situ hybridization in order to accurately measure the nuclear export kinetics of mRNA in mammalian somatic...

integration of wet and dry bench processes optimizes targeted next-generation sequencing of low-quality and low-quantity tumor biopsies

Integration of Wet and Dry Bench Processes Optimizes Targeted Next-generation Sequencing of Low-quality and Low-quantity Tumor Biopsies

An integrated system for targeted next-generation sequencing of oncology specimens is described. This cross-platform system is optimized for low-quality and low-quantity tumor biopsies, accommodates low DNA inputs, includes well-characterized multi-variant controls, and features a novel variant caller that is informed by quantitative pre-analytical quality control measures.

enhancing efficiency and radiolabeling yields of carbon-11 radioligands for clinical research using the loop method

Author Spotlight: Optimized Production of Carbon-11 PET Radiotracers Using Loop Method for Radiolabeling

This protocol presents a detailed procedure to prepare four carbon-11 radiotracers by way of the &#8220;loop method&#8221; [11C]methylation. We describe the procedure to synthesize [11C]ER-176, &#160;with data for three additional radiotracers: [11C]MRB, [11C]mHED, and [11C]PiB. The loop method provides an efficient synthesis with increased radiochemical yields against traditional reaction vessel...

Efficient Synthesis of Carbon-11 Radiotracers Using the Loop Method Methylation

https://cloudfront.jove.com/CDNSource/teasers/67406_b.jpg

Prepare the grinding assembly as per the manufacturer's guidelines, which includes setting up the abrasive plate and attaching the retaining ring equipped with magnets. Then apply 10 drops of pedestal oil onto the pedestals optically flat surface. Place the grinding assembly on the pedestal and initiate the grinding operation.Activate the light source to illuminate the work area, ensuring the light is behind the beveled edge, shining at an angle of 45 degrees to the abrasive plate and needle. Rotate the microscope head in place at 90x magnification. Briefly halt the spinning of the abrasive plate to focus the microscope on the surface of the plate.Add 1%wetting agent to the wick until the wick is completely wet. Then, add 1%wetting agent to the surface of the abrasive plate, ensuring it covers the surface without leaking onto the black retaining ring. Place the pre-wet wick onto the surface of the abrasive plate while it is spinning, ensuring the wick is on the left side of the plate while looking down from the top and stretches from 11 o'clock to six o'clock position with the plate as a clock face.Make sure the wick does not ride on the black portion of the retaining ring.

To begin beveling the borosilicate needle after preparing the grinding assembly, insert the needle into the needle holder and tighten the retaining ring to secure the needle in place. Open the regulator and increase the pressure to 24 pounds per square inch. Rotate the course adjustment knob enough to raise the needle holder till the needle is raised higher than the surface of the rotating abrasive plate.Rotate the entire manipulator so the needle swings into place above the rotating plate. Position the needle on the plate such that the rotation of the plate moves it away from the needle tip. Watching from the side, use the coarse adjustment knob to lower the needle toward the abrasive plate surface and stop when the needle is almost touching the surface of the liquid.Adjust the needle position so that it is in the center of the field of view. Once in the center, slowly increase the magnification, making slight adjustments to keep the needle tip in the center of view. At maximum magnification, stop the grinding plate and focus the microscope on the surface of the abrasive plate.Once the surface is in focus, immediately restart the plate rotation. Using the manipulator course adjustment knob, lower the needle toward the abrasive plate. In the field of view, observe the needle and the shadow of the needle.When the two are close to touching, switch to the fine adjustment knob. Continue lowering the needle until it touches its shadow. At this point, read the caliper and note the reading.This reading indicates the abrasive plate surface is at or below this caliper measurement. Allow the needle to remain at this caliper reading for five to 10 seconds. Using the manipulator fine adjustment knob, raise the needle, while ensuring it stays underneath the surface of the wetting agent.Stop the rotation of the abrasive plate briefly to observe whether bubbles escape from the needle tip. If bubbles are not present, move the needle back to the previous caliper reading. Lower it slightly.Take a new caliper reading and repeat the steps as demonstrated previously. If bubbles are seen, restart the abrasive plate to observe if bubble formation occurs while the plate is rotating. Once bubbles are observed with the abrasive plate not rotating, slowly decrease the air pressure by rotating the regulator adjustment knob.When the bubbles stop flowing from the tip of the needle, note the pressure. Then, increase the air pressure until bubbles start flowing again from the needle tip. Once the beveling is over, raise the needle above the abrasive plate, ensuring it is high enough not to hit anything as the entire manipulator is rotated away from the plate and microscope.Once the needle is in a position where it can be safely removed, lower the air pressure to zero. Remove the needle and place it in a needle storage box like a Petri dish until it is used.