Name: estimating sediment denitrification rates using cores and n2o microsensors
Uploaded: 2018-12-06T13:00:00
Description: Watch this Scientific Journal Video about Estimating Sediment Denitrification Rates Using Cores and N2O Microsensors at JoVE.com

The Spanish Government provided funds through the Ministerio de Educaci&#243;n as a predoctoral fellowship to C.P-L. (FPU12-00644) and research grants of the Ministerio de Economia y Competitividad: NitroPir (CGL2010-19737), Lacus (CGL2013-45348-P), Transfer (CGL2016-80124-C2-1-P). The REPLIM project (INRE - INTERREG Programme. EUUN - European Union. EFA056/15) supported the final writing of the protocol.

1. Preparation
NOTE: Begin this on the day before the measurements are taken.
<ol>
	<li>Assemble the measurement setup (Figure 1a, see the Table of Materials). 
	NOTE: To ensure a constant and high-quality power supply, the measurement device is connected to the grip via an uninterruptible power supply (UPS) that can also act as a backup. In the case of a long-duration power failure, a car battery serve as an extra...

<ol>
	<li>Rockstrom, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+safe+operating+space+for+humanity.">A safe operating space for humanity.</a> Nature. 461 (7263), 472-475 (2009).</li><li>Erisman, J. W., Galloway, J., Seitzinger, S., Bleeker, A., Butterbach-Bahl, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Reactive+nitrogen+in+the+environment+and+its+effect+on+climate+change.">Reactive nitrogen in the environment and its effect on climate change.</a> Current Opinion in Environmental Sustainability. 3 (5), 281-290 (2011).</li><li>Gruber, N., Galloway, J. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Earth-system+perspective+of+the+global+nitrogen+cycle.">An Earth-system perspective of the global nitrogen cycle.</a> Nature. 451 (7176), 293-296 (2008).</li><li>Tiedje, J. M., Zehnder, A. J. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ch.+4.+Ecology+of+denitrification+and+dissimilatory+nitrate+reduction+to+ammonium.">Ch. 4. Ecology of denitrification and dissimilatory nitrate reduction to ammonium.</a> Environmental Microbiology of Anaerobes. Vol. 717. , 179-244 (1988).</li><li>Seitzinger, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+across+landscapes+and+waterscapes:+A+synthesis.">Denitrification across landscapes and waterscapes: A synthesis.</a> Ecological Applications. 16 (6), 2064-2090 (2006).</li><li>Contribution of Working Group I to the fifth assessment report of the intergovernmental panel on climate change. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> IPCC. Climate Change 2013: The Physical Science Basis. , (2013).</li><li>Ravishankara, A. R., Daniel, J. S., Portmann, R. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nitrous+Oxide+(N2O):+The+Dominant+Ozone-Depleting+Substance+Emitted+in+the+21st+Century.">Nitrous Oxide (N2O): The Dominant Ozone-Depleting Substance Emitted in the 21st Century.</a> Science. 326 (5949), 123-125 (2009).</li><li>Balderston, W. L., Sherr, B., Payne, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Blockage+by+acetylene+of+nitrous+oxide+reduction+in+Pseudomonas+perfectomarinus.">Blockage by acetylene of nitrous oxide reduction in Pseudomonas perfectomarinus.</a> Applied and Environmental Microbiology. 31 (4), 504-508 (1976).</li><li>Yoshinari, T., Knowles, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acetylene+inhibition+of+nitrous-oxide+reduction+by+denitrifying+bacteria.">Acetylene inhibition of nitrous-oxide reduction by denitrifying bacteria.</a> Biochemical and Biophysical Research Communications. 69 (3), 705-710 (1976).</li><li>Groffman, P. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Methods+for+measuring+denitrification:+Diverse+approaches+to+a+difficult+problem.">Methods for measuring denitrification: Diverse approaches to a difficult problem.</a> Ecological Applications. 16 (6), 2091-2122 (2006).</li><li>Sorensen, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+rates+in+a+marine+sediment+as+measured+by+the+acetylene+inhibition+technique.">Denitrification rates in a marine sediment as measured by the acetylene inhibition technique.</a> Applied and Environmental Microbiology. 36 (1), 139-143 (1978).</li><li>Revsbech, N. P., Nielsen, L. P., Christensen, P. B., Sorensen, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Combined+oxygen+and+nitrous-oxide+microsensor+for+denitrification+studies.">Combined oxygen and nitrous-oxide microsensor for denitrification studies.</a> Applied and Environmental Microbiology. 54 (9), 2245-2249 (1988).</li><li>Jorgensen, K. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Annual+pattern+of+denitrification+and+nitrate+ammonification+in+estuarine+sediment.">Annual pattern of denitrification and nitrate ammonification in estuarine sediment.</a> Applied and Environmental Microbiology. 55 (7), 1841-1847 (1989).</li><li>Laverman, A. M., Van Cappellen, P., van Rotterdam-Los, D., Pallud, C., Abell, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Potential+rates+and+pathways+of+microbial+nitrate+reduction+in+coastal+sediments.">Potential rates and pathways of microbial nitrate reduction in coastal sediments.</a> FEMS Microbiology Ecology. 58 (2), 179-192 (2006).</li><li>Ambus, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Control+of+denitrification+enzyme-activity+in+a+streamside+soil.">Control of denitrification enzyme-activity in a streamside soil.</a> FEMS Microbiology Ecology. 102 (3-4), 225-234 (1993).</li><li>Christensen, P. B., Rysgaard, S., Sloth, N. P., Dalsgaard, T., Schw&#230;rter, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sediment+mineralization,+nutrient+fluxes,+denitrification+and+dissimilatory+nitrate+reduction+to+ammonium+in+an+estuarine+fjord+with+sea+cage+trout+farms.">Sediment mineralization, nutrient fluxes, denitrification and dissimilatory nitrate reduction to ammonium in an estuarine fjord with sea cage trout farms.</a> Aquatic Microbial Ecology. 21 (1), 73-84 (2000).</li><li>Palacin-Lizarbe, C., Camarero, L., Catalan, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+Temperature+Dependence+in+Remote,+Cold,+and+N-Poor+Lake+Sediments.">Denitrification Temperature Dependence in Remote, Cold, and N-Poor Lake Sediments.</a> Water Resources Research. 54 (2), 1161-1173 (2018).</li><li>. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Nitrous Oxide sensor user manual. , (2011).</li><li>Glew, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Miniature+gravity+corer+for+recovering+short+sediment+cores.">Miniature gravity corer for recovering short sediment cores.</a> Journal of Paleolimnology. 5 (3), 285-287 (1991).</li><li>Andersen, K., Kjaer, T., Revsbech, N. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+oxygen+insensitive+microsensor+for+nitrous+oxide.">An oxygen insensitive microsensor for nitrous oxide.</a> Sensors and Actuators B-Chemical. 81 (1), 42-48 (2001).</li><li>Weiss, R. F., Price, B. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nitrous+oxide+solubility+in+water+and+seawater.">Nitrous oxide solubility in water and seawater.</a> Marine Chemistry. 8 (4), 347-359 (1980).</li><li>. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Nitrous Oxide Microsensors Specifications. , (2018).</li><li>Koike, I., Revsbech, N. P., S&#248;rensen, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ch.+18.+Measurement+of+sediment+denitrification+using+15-N+tracer+method.">Ch. 18. Measurement of sediment denitrification using 15-N tracer method.</a> Denitrification in Soil and Sediment 10.1007/978-1-4757-9969-9 F.E.M.S. Symposium Series. , 291-300 (1990).</li><li>Hvorslev, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Subsurface Exploration and Sampling of Soils for Civil Engineering Purposes. , 521 (1949).</li><li>Glew, J. R., Smol, J. P., Last, W. M., Last, W. M., Smol, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ch.+5.+Sediment+Core+Collection+and+Extrusion.">Ch. 5. Sediment Core Collection and Extrusion.</a> Tracking Environmental Change Using Lake Sediments: Basin Analysis, Coring, and Chronological Techniques. 1, 73-105 (2001).</li><li>Behrendt, A., de Beer, D., Stief, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vertical+activity+distribution+of+dissimilatory+nitrate+reduction+in+coastal+marine+sediments.">Vertical activity distribution of dissimilatory nitrate reduction in coastal marine sediments.</a> Biogeosciences. 10 (11), 7509-7523 (2013).</li><li>Laverman, A. M., Meile, C., Van Cappellen, P., Wieringa, E. B. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vertical+distribution+of+denitrification+in+an+estuarine+sediment:+Integrating+sediment+flowthrough+reactor+experiments+and+microprofiling+via+reactive+transport+modeling.">Vertical distribution of denitrification in an estuarine sediment: Integrating sediment flowthrough reactor experiments and microprofiling via reactive transport modeling.</a> Applied and Environmental Microbiology. 73 (1), 40-47 (2007).</li><li>Melton, E. D., Stief, P., Behrens, S., Kappler, A., Schmidt, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High+spatial+resolution+of+distribution+and+interconnections+between+Fe-+and+N-redox+processes+in+profundal+lake+sediments.">High spatial resolution of distribution and interconnections between Fe- and N-redox processes in profundal lake sediments.</a> Environmental Microbiology. 16 (10), 3287-3303 (2014).</li><li>. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> SensorTrace BASIC 3.0 user manual. , (2010).</li><li>Schwing, P. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sediment+Core+Extrusion+Method+at+Millimeter+Resolution+Using+a+Calibrated,+Threaded-rod.">Sediment Core Extrusion Method at Millimeter Resolution Using a Calibrated, Threaded-rod.</a> Journal of visualized experiments. (114), 54363 (2016).</li><li>Bernhardt, E. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ecology.+Cleaner+lakes+are+dirtier+lakes.">Ecology. Cleaner lakes are dirtier lakes.</a> Science. 342 (6155), 205-206 (2013).</li><li>Finlay, J. C., Small, G. E., Sterner, R. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Human+influences+on+nitrogen+removal+in+lakes.">Human influences on nitrogen removal in lakes.</a> Science. 342 (6155), 247-250 (2013).</li><li>Seitzinger, S. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+in+fresh-water+and+coastal+marine+ecosystems-+ecological+and+geochemical+significance.">Denitrification in fresh-water and coastal marine ecosystems- ecological and geochemical significance.</a> Limnology and Oceanography. 33 (4), 702-724 (1988).</li><li>Seitzinger, S. P., Nielsen, L. P., Caffrey, J., Christensen, P. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+measurements+in+aquatic+sediments+-+a+comparison+of+3+methods.">Denitrification measurements in aquatic sediments - a comparison of 3 methods.</a> Biogeochemistry. 23 (3), 147-167 (1993).</li><li>Christensen, P. B., Nielsen, L. P., Revsbech, N. P., Sorensen, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microzonation+of+denitrification+activity+in+stream+sediments+as+studied+with+a+combined+oxygen+and+nitrous-oxide+microsensor.">Microzonation of denitrification activity in stream sediments as studied with a combined oxygen and nitrous-oxide microsensor.</a> Applied and Environmental Microbiology. 55 (5), 1234-1241 (1989).</li><li>Peter, N. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Denitrification+in+sediment+determined+from+nitrogen+isotope+pairing.">Denitrification in sediment determined from nitrogen isotope pairing.</a> FEMS Microbiology Ecology. 9 (4), 357-361 (1992).</li><li>Risgaard-Petersen, N., Nielsen, L. P., Rysgaard, S., Dalsgaard, T., Meyer, R. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Application+of+the+isotope+pairing+technique+in+sediments+where+anammox+and+denitrification+coexist.">Application of the isotope pairing technique in sediments where anammox and denitrification coexist.</a> Limnology and Oceanography-Methods. 1, 63-73 (2003).</li></ol>

The main advantages of the described method are the use of minimally disturbed sediment core samples and the continuous recording of the N2O accumulation. These allow estimation of relatively low denitrification rates that are likely similar to those occurring in situ. Nonetheless, some aspects concerning the coring, sensor performance, and potential improvements are discussed.
An apparently simple but critical step of the method is good core recovery. The sediment/water in...

Anthropogenic alteration of the nitrogen cycle is one of the most challenging problems for the Earth system1. Human activity has at least doubled the levels of reactive nitrogen available to the biosphere2. However, there remain large uncertainties regarding how the global N cycle is evaluated. A few flux estimates have been quantified with less than &#177;20% error, and many have uncertainties of &#177;50% and larger3. These uncertainties indicate the need for accurate estimations of denitrification rates across ecosystems and an understanding of the underlying mechanisms of variation. Denitrification is a microbial activity through which nitrogenous oxides, mainly nitrate and nitrite, are reduced to dinitrogen gasses, N2O and N24. The pathway is highly relevant to the biosphere availability of reactive nitrogen because it is the primary process of removal5. N2O is a greenhouse gas with a warming potential nearly 300 times that of CO2 over 100 years, and it is the current major cause of stratospheric ozone depletion due to the large quantities being emitted6,7.
In the following, we present a protocol for estimating sediment denitrification rates using cores and N2O microsensors experimentally (Figure 1). Denitrification rates are estimated using the acetylene inhibition method8,9 and measurements of the accumulation of N2O during a defined period (Figure 2 and Figure&#160;3). We demonstrate the method by applying it to mountain lake sediments. This case study highlights the performance of the method for detecting relatively low rates with minimal disturbance to the physical structure of the sediments.
Denitrification is particularly difficult to measure10. There are several alternative approaches and methods, each with advantages and disadvantages. Drawbacks to available methods include their use of expensive resources, insufficient sensitivity, and the need to modify the substrate levels or alter the physical configuration of the process using disturbed samples10. An even more fundamental challenge to measuring N2 is its elevated background levels in the environment10. The reduction of N2O to N2 is inhibited by acetylene (C2H2)8,9. Thus, denitrification can be quantified by measuring the accumulated N2O in the presence of C2H2, which is feasible due to low environmental N2O levels.
The use of C2H2 to measure denitrification rates in sediments was developed about 40 years ago11, and the incorporation of N2O sensors occurred about 10 years later12. The most widely applied acetylene-based approach is the &#34;static core&#34;. The accumulated N2O is measured during an incubation period of up to 24 h after the C2H2 is added to the headspace of the sealed sediment core10. The method described here follows this procedure with some innovations. We add the C2H2 by bubbling the gas in the water phase of the core for some minutes, and we fill all the headspace with sample water before measuring the accumulation of N2O with a microsensor. We also include a stirring system that prevents the stratification of the water without resuspending the sediment. The procedure quantifies the denitrification rate per sediment surface area (e.g., &#181;mol N2O m-2 h-1).
The high spatial and temporal variation of denitrification presents another difficulty in its accurate quantification10. Usually, N2O accumulation is measured sequentially by gas chromatography of headspace samples that are collected during the incubation. The method described provides improved monitoring of the temporal variation of the N2O accumulation, because the microsensor provides a continuous signal. The microsensor multimeter is a digital microsensor amplifier (picoammeter) that interfaces with the sensor(s) and the computer (Figure 1a). The multimeter allows several N2O microsensors to be used at the same time. For instance, up to four sediment cores from the same study site can be measured simultaneously to account for the spatial variability.
The core approach barely disturbs the sediment structure compared to some other methods (e.g., slurries). If the integrity of the sediments is altered, this leads to unrealistic denitrification rates13 that are only adequate for relative comparisons. Higher rates are always obtained with slurry methods compared to core methods14, because the latter preserves the limitation of denitrification by substrate diffusion15. Slurry measures cannot be considered representative of in situ rates16; they provide relative measures for comparisons made with the exact same procedure.
The method described is appropriate for estimating denitrification rates in any sediment type that can be cored. We particularly recommend the method for performing experimental manipulations of some of the driving factors. Examples are experiments that modify nitrate availability and temperature as needed for estimating the energy activation (Ea) of denitrification17 (Figure 2).
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/58553/58553fig1v2.jpg" /> 
Figure 1: Experimental setup. (a) General experimental setup to estimate sediment denitrification rates using cores and N2O microsensors. The incubation chamber ensures darkness and controlled-temperature (&#177;0.3 &#176;C) conditions. Five intact sediment cores can be processed simultaneously using their respective N2O sensors. (b) N2O sensor calibration chamber. We adapted it with rubber stoppers and syringes to mix the N2O water (see protocol step 3.4.3). There is a thermometer to control the water temperature. (c) Close-up of a sediment core sample with the sensor inserted into the central hole of the PVC cover and the joints sealed with adhesive tape. The stirrer is hanging in the water, and the electromagnet is close to it and fixed to the external part of the acrylic tube. (d) Close-up of the N2O microsensor tip protected by a metal piece. (e) A sediment core that has just been recovered. It was sampled from a boat in a deep lake; the acrylic tube with the core is still fixed to the messenger-adapted gravity corer19. See the Table of Materials for all the items needed to perform this method. <a href="https://www.jove.com/files/ftp_upload/58553/58553fig1v2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<table border="0" cellpadding="0" cellspacing="0" style="width:595px;" width="594">
	<colgroup>
		<col />
		<col />
		<col />
		<col />
	</colgroup>
	<tbody>
		<tr height="63">
			<td height="63" style="height:63px;width:227px;">Messenger-adapted gravity corer</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Reference in the manuscript. Made by Glew, J.</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:227px;">Sampling tube</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Acrylic. Dimensions: 100 cm (h) &#215; 6.35 cm (d) &#215; 6.50 cm (D). Sharpen the edge of the sampling tube that penetrates into the sediment to minimize the disturbance in the recovered sediment core sample.</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:227px;">Handheld sounder</td>
			<td style="width:65px;">Plastimo</td>
			<td style="width:100px;">38074</td>
			<td style="width:203px;">Echotest II Depth Sounder.</td>
		</tr>
		<tr height="128">
			<td height="128" style="height:128px;width:227px;">Rubber stopper</td>
			<td style="width:65px;">VWR</td>
			<td style="width:100px;">DENE1012114</td>
			<td style="width:203px;">With two holes, used to mix the N2O-water in the calibration chamber. Dimensions: 20 mm (h) &#215; 14 mm (d) &#215; 18 mm (D) (3 mm hole (D)).</td>
		</tr>
		<tr height="126">
			<td height="126" style="height:126px;width:227px;">Rubber stopper</td>
			<td style="width:65px;">VWR</td>
			<td style="width:100px;">217-0125</td>
			<td style="width:203px;">To seal the bottom part of the methacrylate tube and to sample in shallow water bodies. Dimensions: 45 mm (h) &#215; 56 mm (d) &#215; 65 mm (D).</td>
		</tr>
		<tr height="105">
			<td height="105" style="height:105px;width:227px;">PVC cover</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">To seal the top side part of the acrylic tube. Dimensions: 45 mm (h) &#215; 56 mm (d) &#215; 65 mm (D). Dimensions: 65 mm (D).</td>
		</tr>
		<tr height="105">
			<td height="105" style="height:105px;width:227px;">Adhesive tape</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Waterproof. To ensure all joints (PVC cover sampling tube and PVC cover sensor) and to avoid water leaks.</td>
		</tr>
		<tr height="105">
			<td height="105" style="height:105px;width:227px;">Thermometer</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Portable and waterproof, to measure the temperature in the water overlying the sediment just after sampling the cores.</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:227px;">GPS</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">To save the location of a new sampling site or to arrive at a previous site.</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:227px;">Wader</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">For littoral or shallow site samplings.</td>
		</tr>
		<tr height="84">
			<td height="84" style="height:84px;width:227px;">Boat</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">An inflatable boat is the best option for its lightness if the sampling site is not accessible by car.</td>
		</tr>
		<tr height="84">
			<td height="84" style="height:84px;width:227px;">Rope</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Rope with marks showing its length (e.g., marked with a color code to distinguish each meter).</td>
		</tr>
		<tr height="44">
			<td height="44" style="height:44px;width:227px;">N2O gas bottle and pressure reducer</td>
			<td style="width:65px;">Abell&#243; Linde</td>
			<td style="width:100px;">32768-100</td>
			<td style="width:203px;">Gas bottle reference.</td>
		</tr>
		<tr height="44">
			<td height="44" style="height:44px;width:227px;">C2H2 gas bottle and pressure reducer</td>
			<td style="width:65px;">Abell&#243; Linde</td>
			<td style="width:100px;">32468-100</td>
			<td style="width:203px;">Gas bottle reference.</td>
		</tr>
		<tr height="84">
			<td height="84" style="height:84px;width:227px;">Tube used to evacuate the excess of water</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Consists of a solid part (e.g., a 5 ml pipette tip without its narrowest end) inserted in a silicone tube.</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:227px;">Nitrous Oxide Minisensor w/ Cap</td>
			<td style="width:65px;">Unisense</td>
			<td style="width:100px;">N2O-R</td>
			<td style="width:203px;">We use 4 sensors at a time.</td>
		</tr>
		<tr height="235">
			<td height="235" style="height:235px;width:227px;">Microsensor multimeter 4 Ch. 4 pA channels</td>
			<td style="width:65px;">Unisense</td>
			<td style="width:100px;">Multimeter</td>
			<td style="width:203px;">Picoammeter logged to a laptop. The standard device allows for 2 sensor picoammeter connections (e.g., N2O sensor), one pH/mV and a thermometer. We ordered a device with four picoammeter connections, allowing the use of 4 N2O sensors simultaneously.</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:227px;">SensorTrace Basic 3.0 Windows software</td>
			<td style="width:65px;">Unisense</td>
			<td style="width:100px;"></td>
			<td style="width:203px;">Sensor data acquisition software.</td>
		</tr>
		<tr height="107">
			<td height="107" style="height:107px;width:227px;">Calibration Chamber incl. pump</td>
			<td style="width:65px;">Unisense</td>
			<td style="width:100px;">CAL300</td>
			<td style="width:203px;">Calibration chamber. We tuned it with rubber stoppers and syringes to mix the N2O-water without making bubbles.</td>
		</tr>
		<tr height="105">
			<td height="105" style="height:105px;width:227px;">Incubation chamber</td>
			<td style="width:65px;">Ibercex</td>
			<td style="width:100px;">E-600-BV</td>
			<td style="width:203px;">Indispensable equipment for working at a constant temperature (&#177;0.3 &#176;C). It also allows control of the photoperiod.</td>
		</tr>
		<tr height="126">
			<td height="126" style="height:126px;width:227px;">Electric stirrer</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Part of the stirring system. It hangs in the water, overlying the sediment subject, by a fishing line that is hooked to the PVC cover.</td>
		</tr>
		<tr height="252">
			<td height="252" style="height:252px;width:227px;">Electromagnet</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Part of the stirring system. It is fixed to the outside of the acrylic tube, approximately at the same level as the stirrer. It is activated episodically (ca. 1 on-off per s) by a circuit, attracting the stirrer when it is on and releasing it when it is off, thereby generating the movement that agitates the water.</td>
		</tr>
		<tr height="126">
			<td height="126" style="height:126px;width:227px;">Electromagnetic pulse circuit</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">Part of the stirring system. It is connected by wires to the electromagnet and sends pulses of current that turn the electromagnet on and off.</td>
		</tr>
		<tr height="170">
			<td height="170" style="height:170px;width:227px;">Uninterruptible power supply (UPS)</td>
			<td style="width:65px;">-</td>
			<td style="width:100px;">-</td>
			<td style="width:203px;">It improves the quality of the electrical energy that reaches the measurement device, filtering the highs and low of the voltage, thereby ensuring a more constant and stable N2O sensor signal.</td>
		</tr>
	</tbody>
</table>

estimating sediment denitrification rates using cores and n2o microsensors

Denitrification is the primary biogeochemical process removing reactive nitrogen from the biosphere. The quantitative evaluation of this process has become particularly relevant for assessing the anthropogenic-altered global nitrogen cycle and the emission of greenhouse gases (i.e., N2O). Several methods are available for measuring denitrification, but none of them are completely satisfactory. Problems with existing methods include their insufficient sensitivity, and the need to modify the substrate levels or alter the physical configuration of the process using disturbed samples.This work describes a method for estimating sediment denitrification rates that combines coring, acetylene inhibition, and microsensor measurements of the accumulated N2O. The main advantages of this method are a low disturbance of the sediment structure and the collection of a continuous record of N2O accumulation; these enable estimates of reliable denitrification rates with minimum values up to 0.4-1 &#181;mol N2O m-2 h-1. The ability to manipulate key factors is an additional advantage for obtaining experimental insights. The protocol describes procedures for collecting the cores, calibrating the sensors, performing the acetylene inhibition, measuring the N2O accumulation, and calculating the denitrification rate. The method is appropriate for estimating denitrification rates in any aquatic system with retrievable sediment cores. If the N2O concentration is above the detection limit of the sensor, the acetylene inhibition step can be omitted to estimate the N2O emission instead of denitrification. We show how to estimate both actual and potential denitrification rates by increasing nitrate availability as well as the temperature dependence of the process. We illustrate the procedure using mountain lake sediments and discuss the advantages and weaknesses of the technique compared to other methods. This method can be modified for particular purposes; for instance, it can be combined with 15N tracers to assess nitrification and denitrification or field in situ measurements of denitrification rates.

A total of 468 denitrification rates were estimated using the protocol above in sediments from Pyrenean mountain lakes over the period 2013-2014. We show some of these results to illustrate the procedure (Figure 2 and Figure&#160;3). In general, the linear model between the N2O concentration and time has good correlation (R2 &#8805; 0.9). The slope of the relationship provides an estimate of the denitrificat...

Watch this Scientific Journal Video about Estimating Sediment Denitrification Rates Using Cores and N2O Microsensors at JoVE.com

Estimating Sediment Denitrification Rates Using Cores and N2O Microsensors

This method estimates sediment denitrification rates in sediment cores using the acetylene inhibition technique and microsensor measurements of the accumulated N2O. The protocol describes procedures for collecting the cores, calibrating the sensors, performing the acetylene inhibition, measuring the N2O accumulation, and calculating the denitrification rate.

Estimating Sediment Denitrification Rates Using Cores and N2O Microsensors

Denitrification is the primary biogeochemical process removing reactive nitrogen from the biosphere. The quantitative evaluation of this process has ...

Research

JoVE Journal

Environment

Measuring Rates of Herbicide Metabolism in Dicot Weeds with an Excised Leaf Assay

In order to isolate and accurately determine rates of herbicide metabolism in an obligate-outcrossing dicot weed, waterhemp (Amaranthus tuberculatus), we ...

Sediment Core Sectioning and Extraction of Pore Waters under Anoxic Conditions

We demonstrate a method for sectioning sediment cores and extracting pore waters while maintaining oxygen-free conditions. A simple, inexpensive system is ...

Continuous Instream Monitoring of Nutrients and Sediment in Agricultural Watersheds

Pollutant concentrations and loads in watersheds vary considerably with time and space. Accurate and timely information on the magnitude of pollutants in ...

Preparation of DMMTAV and DMDTAV Using DMAV for Environmental Applications: Synthesis, Purification, and Confirmation

Preparation of DMMTAV and DMDTAV Using DMAV for Environmental Applications: Synthesis, Purification, and Confirmation

Dimethylated thioarsenicals such as dimethylmonothioarsinic acid (DMMTAV) and dimethyldithioarsinic acid (DMDTAV), which are produced by the metabolic ...

Sampling, Sorting, and Characterizing Microplastics in Aquatic Environments with High Suspended Sediment Loads and Large Floating Debris

The ubiquitous presence of plastic debris in the ocean is widely recognized by the public, scientific communities, and government agencies. However, only ...

Laboratory and Field Protocol for Estimating Sheet Erosion Rates from Dendrogeomorphology

Sheet erosion is among the crucial drivers of soil degradation. Erosion is controlled by environmental factors and human activities, which often lead to ...

Investigation of Plant Interactions Across Common Mycorrhizal Networks Using Rotated Cores

Arbuscular mycorrhizal (AM) fungi influence plant mineral nutrient uptake and growth, hence, they have the potential to influence plant interactions. The ...

Measurement of the Potential Rates of Dissimilatory Nitrate Reduction to Ammonium Based on 14NH4+/15NH4+ Analyses via Sequential Conversion to N2O

Measurement of the Potential Rates of Dissimilatory Nitrate Reduction to Ammonium Based on 14NH4+/15NH4+ Analyses via Sequential Conversion to N2O

The importance of understanding the fate of nitrate (NO3&#8722;), which is the dominant N species transferred from terrestrial to aquatic ecosystems, has ...

Sampling for Estimating Frankliniella Species Flower Thrips and Orius Species Predators in Field Experiments

Sampling for Estimating Frankliniella Species Flower Thrips and Orius Species Predators in Field Experiments

The western flower thrips, Frankliniella occidentalis (Pergande), is a polyphagous pest that has been spread worldwide. The extensive use of insecticides ...

Enhanced Oil Recovery using a Combination of Biosurfactants

Biosurfactants are surface-active compounds capable of reducing the surface tension between two phases of different polarities. Biosurfactants have been ...