A Convenient Method for Extraction and Analysis with High-Pressure Liquid Chromatography of Catecholamine Neurotransmitters and Their Metabolites

Podsumowanie

We present a convenient solid-phase extraction coupled to high-pressure liquid chromatography (HPLC) with electrochemical detection (ECD) for simultaneous determination of three monoamine neurotransmitters and two of their metabolites in infants' urine. We also identify the metabolite MHPG as a potential biomarker for the early diagnosis of brain damage for infants.

Streszczenie

The extraction and analysis of catecholamine neurotransmitters in biological fluids is of great importance in assessing nervous system function and related diseases, but their precise measurement is still a challenge. Many protocols have been described for neurotransmitter measurement by a variety of instruments, including high-pressure liquid chromatography (HPLC). However, there are shortcomings, such as complicated operation or hard-to-detect multiple targets, which cannot be avoided, and presently, the dominant analysis technique is still HPLC coupled with sensitive electrochemical or fluorimetric detection, due to its high sensitivity and good selectivity. Here, a detailed protocol is described for the pretreatment and detection of catecholamines with high pressure liquid chromatography with electrochemical detection (HPLC-ECD) in real urine samples of infants, using electrospun composite nanofibers composed of polymeric crown ether with polystyrene as adsorbent, also known as the packed-fiber solid phase extraction (PFSPE) method. We show how urine samples can be easily precleaned by a nanofiber-packed solid phase column, and how the analytes in the sample can be rapidly enriched, desorbed, and detected on an ECD system. PFSPE greatly simplifies the pretreatment procedures for biological samples, allowing for decreased time, expense, and reduction of the loss of targets.

Overall, this work illustrates a simple and convenient protocol for solid-phase extraction coupled to an HPLC-ECD system for simultaneous determination of three monoamine neurotransmitters (norepinephrine (NE), epinephrine (E), dopamine (DA)) and two of their metabolites (3-methoxy-4-hydroxyphenylglycol (MHPG) and 3,4-dihydroxy-phenylacetic acid (DOPAC)) in infants' urine. The established protocol was applied to assess the differences of urinary catecholamines and their metabolites between high-risk infants with perinatal brain damage and healthy controls. Comparative analysis revealed a significant difference in urinary MHPG between the two groups, indicating that the catecholamine metabolites may be an important candidate marker for early diagnosis of cases at risk for brain damage in infants.

Wprowadzenie

Catecholamine neurotransmitters and their metabolite contents in body fluids can affect neural function and affect the balance of response-to-stimulus states to a large extent¹. Abnormities may cause a variety of diseases, such as pheochromacytoma, ganglioneuroma, neuroblastoma, and neurological disorders^1,2. The extraction and determination of catecholamines in body fluids is meaningful to the diagnosis of the relevant diseases. However, catecholamines in biological samples exist in low concentrations and are easily oxidized. Furthermore, they are very difficult to elute because of the large amount of interference in the medium³. Thus, simultaneous detection of catecholamines in biological fluids is still a challenge.

There have been reviews showing that urinary catecholamines can be a measure of stress, and that their levels are important biological markers responding to tactile stimulation processing in newborns⁵. According to the research, all infants who have suffered from premature incidents are at risk for brain injury^4,5,6, and injury may cause abnormal release of catecholamines and related matters into the fluids. There do exist advanced magnetic resonance techniques that can detect brain damage in earlier phases^7,8. However, within the first 48 h, an abnormal neurodevelopmental process will cause permanent brain injury that won't be evident in medical images¹¹. Besides, the high cost and scarce instrument resources, along with other factors, makes it impossible for all neonatal units to have access to these specialized neuro-imaging techniques. However, the use of an easily approachable and practical biomarker (such as catecholamines and their metabolites) could overcome these shortcomings, and the screening of a biomarker in human fluids may help in the early diagnosis of brain injury and lead to prompt identification of new-born infants needing neuroprotection⁹. The catecholamines in urine can be an easy and obvious index, because of the direct correlation between the amount of them released into fluids and neuroactivity function.

Among biological fluids, cerebrospinal fluid (CSF) and plasma samples are not easy to get via existing traumatic procedures, and it is also very difficult to get rid of interference due to adhesive protein and other impurities, leading to a troublesome and time-consuming sampling process that is unsuited for repeated detection. Also, for children, it is almost impossible to get the samples in a traumatic fashion. Therefore, urinary sampling is better than the other forms of sampling, as it is non-invasive, easy to operate, and can be repeatedly done. Urine samples are abundant and easy to store, and show great advantages over the other forms of biological samples.

The main methods to quantify catecholamines in biological fluids include radioenzymic assays¹⁰, enzyme-linked immune-sorbent assays¹¹, voltammetry¹² and thermal lens spectrometry¹³. But shortcomings exist, such as complicated operations and hard-to-detect multiple targets. Today, the dominant analysis technique is high-performance liquid chromatography (HPLC)¹⁴, coupled with sensitive electrochemical¹⁵ or fluorimetric detection¹⁶, because of its high sensitivity and good selectivity. With tandem mass spectrometry technology, such as liquid chromatography /mass spectrometry (LC/MS) and liquid chromatography/mass spectrometry/mass spectrometry (LC/MS/MS), the analysis and quantification of the neurotransmitters can achieve high accuracy and specificity^17,18. However, the MS technique requires expensive instrumentation as well as substantially qualified manpower, making the method difficult to apply universally in most conventional laboratories. HPLC-ECD systems are commonly equipped in most conventional and clinical laboratories, and have thus become a common and good choice for research groups to use for chemical determination, but they require the sample introduced into the system to be clean and of microscale volume¹⁹. Thus, it is of great importance to purify and condense the sample prior to the analysis. The classical method for the purification step is liquid-liquid extraction^14,15,20 and off-line solid-phase extraction, including activated alumina column^21,22 and diphenylborate (DPBA) complexation^23,24,25,26.

Myeongho Lee et al. have been using polymer resin chemically modified with crown ether as the adsorbent to selectively extract catecholamines from human urine since 2007²⁷. Also, in 2006, Haibo He et al. demonstrated a facile synthesis approach for boronate affinity extraction sorbent byutilizing a functionalizable nanomagnetic polyhedral oligomeric silsesquioxane (POSS) based nanomagnetic composite, and applying it to the enrichment of catecholamines in human urine (noradrenaline, epinephrine and isoprenaline)²⁸. They also took advantage of the nanomaterials to fulfill the work, using a technology called nano-electrospinning and forming the polymer fibrous material in the nanoscale. The electrospinning process can adjust the diameter, morphology, and spatial alignment of the product by controlling the working voltage and changing the content of the spinning solution along with other parameters²⁹. Compared with the conventional SPE cartridge, electrospun nanofibers are highly suitable to extract and enrich target analytes from a complex matrix, as they are equipped with high surface-area-to-volume ratios to adsorb the analytes with high efficiency, and exhibit more easily-controlled surface chemical properties, allowing handy attachment of the target compounds. These properties make them good choices for SPE adsorbents, greatly reducing the solid phase and desorption solvent amount^30,31,32,33. For catecholamines in urine samples, electrospun nanofibers composed of apolymeric crown ether with polystyrene (PCE-PS) were used to selectively extract three catecholamines (NE, E, and DA)³⁴. The paper indicated that the selective crown ether adsorbed the targets of NE, E, and DA, which was based on its correct geometry for binding catecholamines via forming hydrogen bonds. The results displayed the material crown ether effectively, removing other interfering compounds contained in biological samples. Inspired by this report, a novel method was developed for the selective extraction of the catecholamines by use of electrospun composite nanofibers composed of PCE-PS.

In this paper, the method reported previously³⁴  was improved and employed not only to successfully analyze E, NE, and DA, but also their metabolites, MHPG and DOPAC, in urine. We also explore new possibilities for the mechanism of the adsorption process. The method shows satisfying extraction efficiency and selectivity for the five analytes, and the method was verified in the analysis of urine from high-risk infants with perinatal brain damage and healthy controls.

Protokół

Informed consent from the parents was obtained, and institutional review board approval was obtained for the study. The study was performed in accordance with the code of Ethics of the World Medical Association (Declaration of Helsinki) for experiments involving humans. Caregivers of all participants provided written consent for being enrolled in the study. Ethical committee approval from Zhongda Hospital, affiliate with Southeast University, was also obtained.

1. Preparation of the Columns and Solutions Needed for the Extraction and Determination of Catecholamines

1. Prepare the PFSPE column. Divide 1-2 mg of PCE-PS nanofibers into 5-6 aliquots, and use a fine steel rod with 0.5 mm diameter to compress them orderly into the end of a pipette tip with a volume of 200 µL.
2. Prepare the artificial urine by weighing 2.427 g urea, 0.034 g uric acid, 0.09 g creatinine, 0.297 g trisodium citrate, 0.634 g sodium chloride, 0.45 g potassium chloride, 0.161 g ammonium chloride, 0.089 g calcium chloride dihydrate, 0.1 g magnesium sulfate heptahydrate, 0.034 g sodium bicarbonate, 0.003 g sodium oxalate, 0.258 g sodium sulfate, 0.1 g sodium dihydrogen phosphate, and 0.011 g disodium hydrogen phosphate, and dissolve the above chemicals into 200 mL deionized water.
3. Prepare 2 mg/mL stock solution of diphenylborate (DPBA) solution by dissolving 2 mg of the compound into 1 mL of distilled water. Store the solution in the dark at 4 °C.
4. Analyte standard
   NOTE: The chemical structure and properties of catecholamines are instable, and they easily decompose. The preparation process of standards has to be very fast and must prevent exposure to direct sunlight.
   1. Weigh 1.0 mg of NE, E, DA, MHPG, DOPAC and internal standard 3,4-dihydroxybenzylamine hydrobromide DHBA in separate 1.5 mL microcentrifuge tubes. Dilute the DHBA solution in water to 100 ng/mL before use.
   2. Oscillate the prepared standards in the dark at a high speed until analytes dissolve completely. This is the primary stock; store at -20 °C for up to several weeks.
   3. Prepare the secondary 1,000 ng/mL analyte stocks. For NE, E, DA, DOPAC and MHPG, transfer 5 µL of each primary analyte stock into 4,975 µL of distilled water in a 5 mL centrifuge tube, and store it in the dark at 4 °C until use. Prepare these solutions fresh daily. For DHBA, transfer 5 µL of primary stock into 4,995 µL of distilled water in a 5 mL centrifuge tube, and store it in the dark separately at 4 °C.
   4. Make further dilutions with the secondary analyte stock to create a standard curve (e.g., Supplementary Table 2). Store solutions in the dark at 4 °C and prepare fresh daily.
   5. Test the optimal voltage of ECD detector using the standard stock with proper concentration. Vary the voltage to find a value where the analytes have the best peak appearance.
5. Prepare eluant containing 30% phosphoric acid, 15% acetonitrile, and 55% distilled water. For 10 mL of eluant solvent, use 5.5 mL of distilled water, and add 1.5 mL of acetonitrile and 3 mL of phosphoric acid drop by drop into the water.

2. Preparation of Real Urine Samples and Mobile Phase

1. Have mothers collect the first morning urine of their infants using aseptic urine cups. Transfer the samples into polypropylene tubes and label immediately. Then, store the samples in a -20 °C freezer.
2. Vortex and centrifuge the urinary samples at 1,510 x g for 10 min at room temperature (RT) to get rid of most particulate interference. Discard the sediment and gather the supernatants for further experiments. In order to extract analytes effectively, proceed to PFSPE pretreatment (step 3) immediately after centrifuging.
3. Prepare the mobile phase
   1. Prepare a clean bottle, at least 1 L. The composition of mobile phase is listed in Supplementary Table 1; for 1 L mobile phase, measure 6.7242 g of citric acid, 93.06 mg of ethylene diamine tetra acetic acid (EDTA) disodium salt, 7.02 g of monometallic sodium orthophosphate, 404.5 mg of 1-heptanesulfonic acid sodium salt, and 3.5 g of sodium hydrate into the bottle. Add 40 mL acetonitrile and distilled water to 1,000 mL. Agitate and vibrate ultrasonically for 15 min until the matter in the solution is all dissolved.
   2. Using a pH meter with a glass electrode, adjust the pH value of the mobile phase to 4.21 with a saturated sodium hydroxide solution.
   3. Filter the mobile phase with a 0.45 µm polyvinylidene fluoride microporous membrane and a vacuum suction device to get rid of impurities.
   4. Use ultrasonic vibration for 15 min to degas the mobile phase each time before use.

3. PFSPE Extraction and HPLC Analysis

1. Activate the nanofibers. Press 100 µL of methanol and 100 µL of water sequentially through the PFSPE column using a 5 mL syringe in a slow, dropwise manner.
2. Mix 100 µL urine sample with 100 µL 2 mg/ml DPBA solution and 30 µL 100 ng/ml of DHBA solution (IS, internal standard) in a 0.5 mL EP tube, then transfer the mixed solution to the PFSPE column. Press the mixed sample solution through the PFSPE column with a 5 mL gastight plastic syringe using the force of the air pressure.
3. Leach the column three times by loading 100 µL of DPBA solution (2 mg/mL) into the SPE column, and push the solution slowly through the cartridge with air pressure using a 5 mL gastight plastic syringe.
4. Load 50 µL of the eluant onto the PFSPE column, and push it through the column, collecting the eluate with a 0.5 mL EP tube.
5. Turn on the HLPC degasser to degas the air in the system. Prior to sample analyses, the system should run for more than 0.5 h with the mobile phase to equilibrate and reduce baseline noise. See Supplementary Table 1 showing the setup parameters of the HPLC system.
6. Sample 20 µL of the eluate using an automatic sampler, and then inject it into the HPLC-ECD system.
7. When the runs are complete, turn off the detector cell using the detector interface. DO NOT turn off the cell with the switch at the back of the detector, as this could damage the instrument.
8. Manually change the mobile phase composition to 10% methanol and 90% water. Run for at least 30 min. Then, manually change the mobile phase to HPLC-grade methanol. Run for about 15 min to protect the system in methanol. Failure to run this step following the recommended running time could result in damage to the column and the detector. Turn off the flow, then turn off the degasser.

4. Phenylboronic Acid Cartridges (PBA) Extraction

PBA cartridge extraction procedures were similar to the scheme in Kumar et al. (2011)²⁵. All solutions are pushed through the PBA cartridge (100 mg, 1 mL) with air forced by a syringe.

1. Condition the cartridge with 1 mL 80:20 acetonitrile-water (v/v) containing 1% formic acid and 1 mL of 50 mM phosphate buffer (pH 10) sequentially.
2. Press the buffered urine sample (1 mL urine and 2 mL phosphate buffer, pH 8.5) through the PBA cartridge.
3. Wash the cartridge with 1 mL 50:50 v/v acetonitrile-phosphate buffer (10 mM, pH 8.5).
4. Elute the cartridge with 1 mL acetonitrile-water (80:20 v/v) containing 1% formic acid.

5. Identification and Quantification of Catecholamines

1. Linearity
   1. Dilute the secondary analytes stock with artificial urine to six concentrations (1.5, 3, 12, 25, 50, and 100 ng/mL); the dilution volume of artificial urine follows Supplementary Table 2. Make three parallel samples with each concentration to get 18 analyte experimental solutions for constructing calibration curves.
   2. Dilute DHBA secondary stock with artificial urine 10-fold to get 100 ng/mL experimental solution.
   3. Pretreat all the analyte solutions from 5.1.1, according to step 3 (PFSPE extraction procedures). As in Step 3, inject 20 µL of each corresponding eluate into the HPLC-ECD system to get an HPLC chromatogram.
   4. Construct calibration curves of the five analytes by plotting the ratio of peak area (targets/IS) as the Y axis against the ratio of concentrations (targets/IS) as the X axis, as shown in Supplementary Figure 1.
2. LOD and LOQ value for sensitivity
   1. Inject 20 µL of the blank artificial urine into the HPLC-ECD system (as in Step 3), to obtain the HPLC chromatogram of the sample.
   2. In the chromatogram from 5.2.1, collect 11 blank signal values, and calculate the mean value X_b and standard deviation S_b. Calculate the minimum signal of a substance that can be detected at a certain level of confidence, X_L, as X_L = X_b+K*S_b (K is the coefficient determined by confidence level, S_b reflects noise level of the measuring method and the level of machine noise). Thus, LOD = (X_L-X_b)/S = (K*S_b)/S (S stands for the slope value of the working curve).
   3. Define an S/N of 3:1 (K=3) as the limit of detection (LOD), and an S/N of 10:1 (K=10) as the limit of quantification (LOQ).
3. Evaluate the recoveries
   1. Prepare real and spiked urine samples. Dilute the secondary analytes stock with real urine to three concentrations (5, 50, 100 ng/mL) to obtain the spiked urine samples. Prepare three parallel samples for each analyte solution. Count the spiked concentration as the quantity of target compounds spiked into the urine sample. Define this value as A_s.
   2. Dilute DHBA stock to 100 ng/mL, as in step 5.1.2.
   3. Process each sample solution from 5.3.1 according to step 3 (PFSPE extraction procedures) and inject the 20 µL of each corresponding eluant into the HPLC-ECD system to get the chromatogram result. The value of analytes will be counted as a quantity of target compounds quantified in the spiked urine sample. Define this value as A_t.
   4. Inject 20 µL of urine sample into the HPLC-ECD (as in step 3) system to get the chromatogram result. The value of analytes will be counted as an initial quantity of target compounds quantified in the urine sample. Define this value as A_i.
   5. Calculate the quantity of target compounds in the samples from the standard curve equation. The percentage recovery is estimated as methodological recovery % = (A_t - A_i) × 100/(A_s). Mean values are shown in Table 1.
4. Evaluate the imprecision
   1. Prepare spiked artificial urine samples to 5, 50, and 100 ng/mL concentrations as in step 5.3.1. Prepare six parallel samples for each analyte solution. Prepare fresh experimental samples every day.
   2. Dilute DHBA stock to 100 ng/mL as in step 5.1.2.
   3. Evaluate the intra-day precision (n=6). Process each sample solution in 5.4.1 according to step 3 and inject the 20 µL of each correspondent eluant into the HPLC-ECD system to get the chromatogram. Do the same operation six times in the same day.
   4. Calculate the quantity of target compounds in the samples from the standard curve equation. Under the same concentration of the same compound, the relative standard deviation (RSD) of the six assays in one day is determined as intra-day precision. Mean values are shown in Table 1.
   5. Evaluate the inter-day precision (n=6). At the same time each day in the six sequential days, prepare spiked artificial urine samples for three concentrations of 5, 50, 100 ng/mL, as in 5.4.1 and 5.4.2., and process each analyte sample solution according to step 3.
   6. Inject the 20 µL of each corresponding eluate from 5.4.5 into the HPLC-ECD system to get chromatogram results each day. Calculate the quantity of target compounds in the samples from the standard curve equation. Inter-day precision is expressed by the RSD of the assays quantity from the spiked artificial urine samples at the three concentrations in six sequential days. Mean values are shown in Table 1.

Wyniki

This protocol is a simple and convenient PFSPE method to pretreat urine samples and enrich five catecholamines for detection via an HPLC-ECD system; a diagram of the process is shown in Figure 1. The protocol mainly includes four steps-activating, loading, rinsing, and eluting- coupled with a small quantity of PCE-PS nanofibers and a simple solid-phase extraction device. The morphology of PCE-PS nanofibers was assessed using a surface and porosity analyzer (s...

Dyskusje

The proposed PFSPE method in this paper may be significant and meaningful with respect to its rapidity, simplicity, and convenience. The adsorbents used in the protocol are electrospun nanofibers, which have high surface area-to-volume ratios, and adsorb the analytes with high efficiency. The procedure only needs a few milligrams of nanofiber and a small volume of eluant solvent, and does not require an evaporation step to concentrate the analytes. Here, we have presented a detailed overview of an HPLC-ECD based protocol...

Materiały

Name	Company	Catalog Number	Comments
200 µL pipette tip			column to contain nanofibers
PCE-PS nanofibers			material for PFSPE extraction
steel rod (about 0.5 mm diameter)			fill the nanofibres into the column
gastight plastic syringe (5 ml)			compress solution into the end of the tip
methanol	Sinopharm Chemical ReagentCo., Ltd	67-56-1
diphenylborinic acid 2-aminoethyl ester(DPBA)	Sigma-Aldrich.Inc	A-106408	complex reagent
norepinephrine(NE)	Sigma-Aldrich.Inc	A-9512	analyte
3-Methoxy-4-hydroxyphenylglycol(MHPG)	Sigma-Aldrich.Inc	H1377	analyte
epinephrine(E)	Sigma-Aldrich.Inc	100154-200503	analyte
3, 4-Dihydroxyphenylacetic acid(DOPAC)	Sigma-Aldrich.Inc	D-9128	analyte
dopamine(DA)	Sigma-Aldrich.Inc	H-8502	analyte
3, 4-dihydroxybenzylamine hydrobromide(DHBA)	Sigma-Aldrich.Inc	858781	interior label
acetonitrile	Sigma-Aldrich.Inc	75-05-8	eluriant and mobile phase
phosphoric acid	Sinopharm Chemical ReagentCo., Ltd	7664-38-2	eluriant
uric acid	Sinopharm Chemical ReagentCo., Ltd	69-93-2	artifical urine
creatinine	Sinopharm Chemical ReagentCo., Ltd	60-27-5	artifical urine
trisodium citrate	Sinopharm Chemical ReagentCo., Ltd	6132-04-3	artifical urine
KCl	Sinopharm Chemical ReagentCo., Ltd	7447-40-7	artifical urine
NH4Cl	Sinopharm Chemical ReagentCo., Ltd	12125-02-9	artifical urine
NaHCO3	Sinopharm Chemical ReagentCo., Ltd	SWC0140326	artifical urine
C2Na2O4	Sinopharm Chemical ReagentCo., Ltd	62-76-0	artifical urine
NaSO4	Sinopharm Chemical ReagentCo., Ltd	7757-82-6	artifical urine
disodium hydrogen phosphate	Sinopharm Chemical ReagentCo., Ltd	10039-32-4	artifical urine
urea	Sinopharm Chemical ReagentCo., Ltd	57-13-6	artifical urine
NaCl	Sinopharm Chemical ReagentCo., Ltd	7647-14-5	artifical urine
MgSO4.7H2O	Sinopharm Chemical ReagentCo., Ltd	10034-99-8	artifical urine
CaCl2	Sinopharm Chemical ReagentCo., Ltd	10035-04-8	artifical urine
HCl	Sinopharm Chemical ReagentCo., Ltd	7647-01-0	artifical urine
citric acid	Sinopharm Chemical ReagentCo., Ltd	77-92-9	artifical urine and mobile phase
EDTA disodium salt	Sinopharm Chemical ReagentCo., Ltd	34124-14-6	mobile phase
monometallic sodium orthophosphate	Sinopharm Chemical ReagentCo., Ltd	7558-80-7	artifical urine and mobile phase
1-heptanesulfonic acid sodium salt	Sinopharm Chemical ReagentCo., Ltd	22767-50-6	mobile phase
sodium hydroxide	Sinopharm Chemical ReagentCo., Ltd	1310-73-2	mobile phase
phenylboronic acid column(PBA column)	Aglilent	12102018	PBA extraction
Inertsil® ODS-3 5 µm 4.6×150 mm column	Dikma	5020-06731	HPLC column for seperation
SHIMADZU SIL-20AC prominence AUTO SAMPLER	Shimadzu Corporation, Japan	SIL-20AC	auto injection for eluriant
SHIMADZU LC-20AD High Performance Liquid Chromatography	Shimadzu Corporation, Japan	LC-20AD	HPLC pump
SHIMADZU L-ECD-60A electrochemical detector	Shimadzu Corporation, Japan	L-ECD-60A	detector for the analytes
ASAP 2020 Accelerated Surface Area and Porosimetry System	Micromeritics, USA		surface and porosity analyzer