Use of Micro X-ray Computed Tomography with Phosphotungstic Acid Preparation to Visualize Human Fibromuscular Tissue

Podsumowanie

Micro X-ray computed tomography is effective in obtaining three-dimensional information from undamaged human specimens but has limited success in observing soft tissues. The use of phosphotungstic acid contrast agent can resolve this issue. We implemented this contrast agent to examine human delicate fibromuscular tissues (the orbicularis retaining ligament).

Streszczenie

Manual dissection and histological observation are common methods used to investigate human tissues. However, manual dissection can damage delicate structures while processing and histological observation provide limited information through cross-sectional imaging. Micro X-ray computed tomography (microCT) is an effective tool for obtaining three-dimensional information without damaging specimens. However, it shows limited efficiency in differentiating soft tissue parts. Use of contrast-enhancing agents, like phosphotungstic acid (PTA), can solve this problem by improving soft tissue contrast. We implemented microCT with PTA to investigate the human orbicularis retaining ligament (ORL), which is a delicate structure in the orbit area. In this method, harvested specimens are fixed in formalin, dehydrated in serial ethanol solutions, and stained with a PTA solution. After staining, microCT scanning, 3D reconstruction, and analysis are performed. Skin, ligaments, and muscles can be clearly visualized using this method. The specimen size and duration of staining are essential features of the method. The suitable specimen thickness was about 5–7 mm, above which the process was slowed, and the optimum duration was 5–7 days, below which an empty hole in the central area occasionally occurred. To maintain the location and direction of small pieces during cutting, sewing on the same region of each part is recommended. Furthermore, preliminary analyses of the anatomical structure are needed to correctly identify each piece. Parafilm can be used to prevent drying, but care should be taken to prevent specimen distortion. Our multidirectional observation showed that the ORL is composed of a multilayered meshwork of continuous plates, rather than thread-like fibers, as reported previously. These results suggest that microCT scanning with PTA is useful for examining specific compartments within complex structures of human tissue. It may be helpful in the analyses of cancer tissues, nerve tissues, and various organs, like the heart and liver.

Wprowadzenie

Manual dissection and histological observation are typically used to examine human tissues, such as muscles and connective tissues. However, manual dissection can easily damage delicate structures, and histological observation provides limited information about flat cross-sectional surfaces^1,2. Therefore, improved methods are needed to examine tissues more precisely and efficiently.

Conventional computed tomography (CT) is generally used in clinical practice, but it lacks the ability to distinguish small structures^2,3. Micro X-ray CT (microCT) is an effective tool for obtaining three-dimensional (3D) information of small structures from specimens, without destroying them. However, microCT has limited applications because only dense tissues can be visualized clearly; it cannot be used to differentiate soft tissues. To overcome this limitation, staining agents can be used. Contrast-enhancing agents, like phosphotungstic acid (PTA), phosphomolybdic acid, and Lugol’s iodine, improve the soft tissue contrast rate during scanning^4,5. Several studies comparing these agents suggest that PTA demonstrates good performance and is easy to handle^6,7,8.

The orbicularis retaining ligament (ORL) is a delicate structure around the orbit, which can be easily damaged during conventional observation⁹. We examined and successfully retrieved 3D information on this structure using microCT with PTA as a contrast agent. This method can be applied to studies on other human tissues, such as the heart and liver, with appropriate modifications^10,11,12.

Protokół

All cadavers utilized in this study were legally donated to the Surgical Anatomy Education Centre at Yonsei University College of Medicine.

1. Obtaining samples

1. Draw an incision line on the cadaver with a colored pencil to indicate the cutting area for sample harvesting. Check that the incision line drawn extends medially to a medial canthus, laterally to a lateral canthus, superiorly to a superior border of the lower eyelid, and inferiorly to 1 cm below the line from the orbital rim.
   NOTE: Consider the sample size based on the maximum scanning size of the micro-CT equipment (our equipment could acquire an image with a maximum object dimension of 7 × 7 cm). Here, a sample approximately 1 cm in width, 3 cm in length, and 1.25 g weight was harvested from the ORL region.
2. Cut the facial tissues following the incision line with a blade. Make sure the cut is deep such that the tip of the blade touches the bone. The sample must include the skin, subcutaneous tissue, muscle, fat, and periosteum.
3. Fix the sample in 10% formalin immediately and preserve it for 5 to 7 days at room temperature (Figure 1A).
   NOTE: Both embalmed and fresh cadavers can be used for this study. However, the fixation solution for cadavers might differ slightly from the solution used in a biological experiment. Therefore, we suggest fixing the sample with 10% formalin again even after obtaining the sample from embalmed cadavers.

2. Preparation for staining

1. After fixing, slice the sample into 3 pieces (5–7 mm in thickness). Do not lose the location and direction of each piece during this process.
   NOTE: The microCT scanner we use can cover a maximum size of 7 cm³, but the PTA solution cannot penetrate the sample successfully if it is too thick.
2. Sew the superolateral side of each piece using a needle and black thread such that the direction of the sample can be checked later.
3. Dehydrate the sample in a series of 30%, 50%, and 70% ethanol solutions for 1 day each.
4. Place the sample in 70% ethanol until staining.

3. PTA preparation

1. Begin the PTA staining process 1 week before microCT scanning is scheduled.
2. Prepare 210 mL of 70% ethanol solution and add 2.1 g of PTA power to it. Mix well using a shaker at 55-60 rpm.
   NOTE: The concentration of the PTA solution should be 1% in ethanol.
3. Prepare three 70 mL plastic containers for each sliced piece. Fill the containers with the PTA solution. Soak the specimens into the containers and place them on a shaker for effective penetration. Leave the samples for 5–7 days (Figure 1B).
4. When the staining is completed, store the sample in 70% ethanol to prepare for scanning.
   NOTE: The stained samples can be maintained for several months, but it is recommended that the samples be scanned as soon as possible to ensure full staining.

4. MicroCT scanning

1. Wrap the sample with parafilm to prevent drying. Do not wrap the samples too tight, as that may lead to deformation.
2. Open the scanner and place the sample on the tray (Figure 2).
3. Set the scanning parameters as follows: source voltage (kV) = 70, source current (μA) = 114, Al filter = 0.5 mm, image pixel size (μm²) = 20, pixels = 2240 × 2240, exposure (ms) = 500, rotation step (deg) = 0.3.
   NOTE: The parameters may be modified according to the samples and/or scanners used.
4. Start scanning.
   NOTE: Scanning takes 30 to 60 min depending on the intended resolution and the speed of the scanner.

5. Reconstruction and optimization of data

1. Run the reconstruction software. Select Open Dataset on the Actions menu to launch the scanned files.
2. Select the Settings tab on the Reconstruction window. Set the parameters as follows: Ring artifacts reduction = 7, Beam-hardening correction (%) = 40.
   NOTE: The parameters can be modified according to the sample.
3. Begin reconstruction by selecting Start on the Start tab. The final data will be stored in the designated folder.
4. Run the file resizing software. Select Source data set to launch the reconstructed files.
5. Select jpg on the Destination data set tab.
6. Choose the Resizing option 1/2 with a Quality option of No interpolation (fast).
7. Adjust the slide bar to 100 (highest) in the Image compression tab. Start converting.
   NOTE: The resizing option is to avoid slowing down the computer speed when 3D rendered; however, it can result in lower resolution when resized extensively. We suggest resizing in half for acceptable resolution with better handling.

6. 3D reconstruction

1. Run the 3D volume rendering software.
2. Select Actions > Load volume data to launch the dataset.
3. Adjust the brightness and contrast level by modifying shape transfer function in histogram in the Transfer Function Editor tab.
4. Select Options > Lighting.
5. Select Shadows and Surface Lighting icons. These effects provide a realistic modeling tone.
6. Find the best view by moving (click and drag), rotating (right-click and drag), and zooming in or out of (scroll) the model.
7. Slide the plane (shift + click and drag in the inner direction) to show the sectional images (Figure 3).
8. Turn on Light icon. Adjust the lighting indication bar and find the best lighting for viewing. Then, turn off the icon and close the Lighting tab.
9. Select Options > Show > Clipping Box to hide the box for the final image.
10. Select Actions > Save image to store the image.

Wyniki

The detailed reconstruction of the ORL was achieved by microCT with PTA preparation (Figure 4). The ligamentous fibromuscular structure extending obliquely between the dermis and periosteum was distinctly observed (Figure 4A). In the coronal view (Figure 4B), the amount and complexity of fibers increased laterally. In the horizontal view (Figure 4C), an elaborate meshwork with an arborized formation was...

Dyskusje

We implemented microCT with PTA preparation in the examination of human soft tissues. Briefly, specimens are harvested and fixed in formalin for a few days, followed by dehydration in serial ethanol solutions. Placing the sample into the PTA solution directly after formalin fixation can result in some tissue cracking due to rapid dehydration. Therefore, serial dehydration is needed before PTA staining. Next, the samples are stained using PTA solution for about a week. MicroCT scanning, 3D reconstruction, and analysis can...

Materiały

Name	Company	Catalog Number	Comments
12 Tungsto(VI)phosphoric acid n-hydrate Phosphotungstic acid	Junsei	84220-0410	PTA powder
CTvox	Bruker	ver 2.7	3D recon software
Nrecon	Bruker	ver 1.7.0.4	Reconstruction software
Skyscan	Bruker	1173	MicroCT scanner
Tconv	Bruker	ver 2.0	File resizing software