The authors would like to thank Professor Howard Ceri from the Biological Sciences Department of the University of Calgary for providing bacterial strains. A. Kumar acknowledges support from NSERC. T. Thundat acknowledges financial support from the Canada Excellence Research Chair (CERC) program. The authors would also like to acknowledge help from Ms. Zahra Nikakhtari for help with videography.

Perform the experimental protocols here in the order described below. Microfabrication protocols for creating the microfluidic platform are discussed in Step 1. Step 2 describes the bacterial culture protocol (Figure 2), and Step 3 pertains to assembly of the experimental setup (Figure 3). Finally, the actual experimental step is described in Step 4.
1. Chip Fabrication Procedure
NOTE: Proper safety procedures must be followed for the processes described below. Consult the institutional safety officer for details.
<ol>
	<li>Design the mask with an appropriate software (e.g., L-Edit). The channel design consists of a main micro-channel of width 625 &#956;m. The central region of the channel contains an array of micro-posts 50 &#956;m in diameter, spaced 25 &#956;m apart (See Supplemental Files).</li>
	<li>Print this design on glass (5&#34; x 5&#34; soda lime glass), which has a thickness of 0.09&#34; and is coated by approximately 70 nm thick layer of Chromium (Cr), using masking in order to prepare a photo mask. Use AZ400K developer for 1 min. Then, etch the Cr layer using Cr etchant for about 1 min. Use acetone to strip the resist and clean it with cold piranha solution (H2SO4 and H2O2 in a ratio of 3:1).</li>
	<li>Photolithography
	<ol>
		<li>Clean a standard 4&#34; silicon wafer chemically with piranha solution for 20 min.</li>
		<li>Rinse the wafer with DI water and dry it.</li>
		<li>Heat the wafer on a hot plate (200 &#176;C for 15 min).</li>
		<li>Coat the silicon wafer with photoresist. Here, the positive photoresist AZ4620 was spin-coated on a silicon wafer at 2,000 rpm for 25 sec to obtain a 12.5 &#956;m thick layer.</li>
		<li>Remove all the solvent by soft baking of the wafer on a hot plate by floating the wafer for 90 sec&#160;on nitrogen flow at 100 &#176;C. Then, keep it in vacuum at the same temperature for 60 sec.</li>
		<li>Place the wafer in a dark box for 24 hr for dehydration.</li>
		<li>Expose the wafer to UV light in order to transfer the designed pattern to the photoresist.</li>
		<li>Immerse the wafer in photoresist developer solution (AZ400K) for 240 sec. Then, rinse the wafer with isopropyl alcohol and dry it by placing in a stream of nitrogen gas.</li>
	</ol>
	</li>
	<li>ICP-DRIE (Inductively Coupled Plasma - Deep Reactive Ion Etching) Process
	<ol>
		<li>Apply DRIE etching. Choose the appropriate etch depth according to final depth required for device (50 &#956;m in this investigation). Photoresist acts as a masking layer during this process.</li>
		<li>Remove the remaining photoresist with acetone and clean the wafer.</li>
	</ol>
	</li>
	<li>PDMS (polydimethylsiloxane) Casting
	<ol>
		<li>Use trichloromethylsilane (TCMS) for silanizing the silicon master mold. Pour 2 or 3 drops of trichloromethylsilane in a vial and place it in a desiccator beside the silicon master mold. Allow 2-3 hr for the silanizing process to complete.</li>
		<li>In a separate container, mix the Sylgard 184 silicone base with curing agent by weight ratio of 10:1 to prepare PDMS. Degas the PDMS by subjecting it to vacuum conditions (about 2 hr).</li>
		<li>Put the silicon master mold in a holder. Then, pour the PDMS on the silicon master mold to form the PDMS stamp. Ensure that bubbles do not form in the PDMS during this process.</li>
		<li>Cure the PDMS for 2 hr at 80 &#176;C.</li>
		<li>Peel off the PDMS stamp from the master mold. Then, cut the PDMS stamp into separate microchips. Finally, use a cutting core to drill holes for the inlet(s) and outlet(s).</li>
	</ol>
	</li>
	<li>Bonding of PDMS to Glass
	<ol>
		<li>Expose the cover slip and PDMS stamp to oxygen plasma for 30 sec. Bond PDMS stamp to the cover slip.</li>
		<li>To achieve proper sealing between the PDMS stamp and the cover slip, anneal the device by putting it in oven at 70 &#176;C for 10 min.</li>
	</ol>
	</li>
</ol>
2. Bacterial Culture
NOTE: Proper biosafety protocols must be followed for Steps 2-4. Consult the institutional safety officer for details.
<ol>
	<li>Prepare LB Agar Plates
	<ol>
		<li>Add 20 g Luria-Bertani (LB) agar (Miller) powders and 500 ml&#160;of ultrapure water to a 1 L flask. Stir to dissolve the powder.</li>
		<li>Sterilize by autoclaving at 15 psi, 121 &#176;C for 15 min.</li>
		<li>Allow the flask to cool down to 50-55 &#176;C on a bench or in a water bath in the biosafety hood.</li>
		<li>Add the antibiotic Tetracycline to achieve a final concentration of 50 &#956;g/ml. Mix well by swirling.</li>
		<li>Pour the mixture into plates. Fill each plate till 1/2 - 2/3 full.</li>
		<li>Flame air bubbles briefly to pop them if they form. Solidified air bubbles are difficult to spread bacterial culture over.</li>
		<li>Allow the plates to cool at room temperature overnight.</li>
		<li>When they are cool, put plates back into their sleeve, seal the bag, label (antibiotic and date), and store at 4 &#176;C. 
		NOTE: Cover the stock of plates with tin foil, as light deactivates many antibiotics.</li>
	</ol>
	</li>
	<li>LB Broth Preparation
	<ol>
		<li>Add 20 g Luria-Bertani (LB) broth (Miller) powders and 1 L&#160;of ultrapure water to a&#160;flask. Stir to dissolve the powder.</li>
		<li>Sterilize by autoclaving at 15 psi, 121 &#176;C for 15 min.</li>
		<li>Allow flask to cool down to 50-55 &#176;C on a bench or in a water bath in the biosafety hood.</li>
		<li>Add the antibiotic tetracycline to achieve a final concentration of 50 &#956;g/ml. Mix well by swirling.</li>
		<li>When cool, place the labeled bottle at 4 &#176;C. 
		NOTE: Cover the bottle with tin foil, as light deactivates many antibiotics.</li>
	</ol>
	</li>
	<li>Culture Bacteria on an LB Agar Plate (This protocol uses Pseudomonas fluorescens)
	<ol>
		<li>Take the bacterial stock from the freezer (-80 &#176;C) and place it on ice.</li>
		<li>Place the -80 &#176;C bacterial stock and an LB agar plate inside a biosafety hood.</li>
		<li>Streak the bacterial strain onto an LB agar plate in a zigzag pattern. Cover the agar plate and incubate it at 30 &#186;C overnight. Finally, store the plate in the refrigerator at 4 &#176;C.</li>
	</ol>
	</li>
	<li>Prepare the Bacterial Solution (S1)
	<ol>
		<li>Pour 50 ml LB broth media to an autoclaved flask. Perform this operation inside a biosafety hood.</li>
		<li>Transfer a single bacterial colony from the LB agar plate to the flask. This operation should also be performed inside a biosafety hood.</li>
		<li>Put the flask in a shaker incubator at 30 &#176;C and 150 rpm for adequate time (4 hr).</li>
	</ol>
	</li>
	<li>Prepare the Dilute Bacterial Solution (S2)
	<ol>
		<li>Pour 5 ml LB broth media into a sterilized plastic tube.</li>
		<li>Dilute S1 by mixing with LB broth media. Then, vortex the solution. Dilute the solution achieve the desired optical density (OD measured at 600 nm = 0.1). 
		NOTE: Biofilm experiments typically employ OD values in this vicinity.</li>
	</ol>
	</li>
</ol>
3. Prepare the Experimental Setup
<ol>
	<li>Using tweezers connect flexible plastic tubes (0.20&#34; ID) into the inlet(s) and outlet(s) of the microchip. The inlets and outlets were previously drilled into the PDMS portion of the microchip (step 1.5.5). In this investigation, the microchip consists of two inlets and one outlet.</li>
	<li>Fill syringe(s) with bacterial solution (S2 solution) and remove all the bubbles in the syringe(s).</li>
	<li>Connect syringe tip(s) (30 G 0.5&#34; blunt needle) into inlet tube(s). Then, connect outlet tube(s) to waste container.</li>
</ol>
4. Run the Experiment
<ol>
	<li>Connect the syringe(s) to the syringe tip(s).</li>
	<li>Place and fix syringe(s) onto the syringe pump. Then place the microchip under an optical microscope with objective lenses of desired magnification (e.g., 40X). Cover the microchip with a live cell chamber device to maintain a constant temperature environment for bacterial growth (30 &#176;C for P. fluorescens).</li>
	<li>Set the pump to the desired flow rate level (say 10 &#956;l/hr) and initiate fluid pumping.</li>
	<li>Once bacteria are introduced into the chamber, biofilm formation is also initiated. Biofilm formation and maturation typically occur over a period of several hours or even days. Observe and take images of biofilm growth through the microscope.</li>
</ol>

<ol>
	<li>Valiei, A., Kumar, A., Mukherjee, P. P., Liu, Y., Thundat, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+web+of+streamers:+biofilm+formation+in+a+porous+microfluidic+device.">A web of streamers: biofilm formation in a porous microfluidic device.</a> Lab Chip. 12, 5133-5137 (2012).</li><li>Costerton, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bacterial+Biofilms:+A+Common+Cause+of+Persistent+Infections.">Bacterial Biofilms: A Common Cause of Persistent Infections.</a> Science. 284, 1318-1322 (1999).</li><li>Flemming, H. C., Wingender, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+biofilm+matrix.">The biofilm matrix.</a> Nat Rev Microbiol. 8, 623-633 (2010).</li><li>Wong, G. C. L., O&#8217;Toole, G. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=All+together+now:+Integrating+biofilm+research+across+disciplines.">All together now: Integrating biofilm research across disciplines.</a> MRS Bulletin. 36, 339-342 (2011).</li><li>Yazdi, S., Ardekani, A. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bacterial+aggregation+and+biofilm+formation+in+a+vortical+flow.">Bacterial aggregation and biofilm formation in a vortical flow.</a> Biomicrofluidics. 6, 044114 (2012).</li><li>Rusconi, R., Lecuyer, S., Guglielmini, L., Stone, H. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laminar+flow+around+corners+triggers+the+formation+of+biofilm+streamers.">Laminar flow around corners triggers the formation of biofilm streamers.</a> J R Soc Interface. 7, 1293-1299 (2010).</li><li>Drescher, K., Shen, Y., Bassler, B. L., Stone, H. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biofilm+streamers+cause+catastrophic+disruption+of+flow+with+consequences+for+environmental+and+medical+systems.">Biofilm streamers cause catastrophic disruption of flow with consequences for environmental and medical systems.</a> P Natl Acad Sci USA. 110, 4345-4350 (2013).</li><li>Marty, A., Roques, C., Causserand, C., Bacchin, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Formation+of+bacterial+streamers+during+filtration+in+microfluidic+systems.">Formation of bacterial streamers during filtration in microfluidic systems.</a> Biofouling. 28, 551-562 (2012).</li><li>Taherzadeh, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Computational+Study+of+the+Drag+and+Oscillatory+Movement+of+Biofilm+Streamers+in+Fast+Flows.">Computational Study of the Drag and Oscillatory Movement of Biofilm Streamers in Fast Flows.</a> Biotechnol Bioeng. 105, 600-610 (2010).</li><li>Vrouwenvelder, J. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Impact+of+flow+regime+on+pressure+drop+increase+and+biomass+accumulation+and+morphology+in+membrane+systems.">Impact of flow regime on pressure drop increase and biomass accumulation and morphology in membrane systems.</a> Water Res. 44, 689-702 (2010).</li><li>Mitchell, A. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biofilm+enhanced+geologic+sequestration+of+supercritical+CO2.">Biofilm enhanced geologic sequestration of supercritical CO2.</a> International Journal of Greenhouse Gas Control. 3, 90-99 (2009).</li><li>Soleimani, S., Van Geel, P. J., Isgor, O. B., Mostafa, M. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modeling+of+biological+clogging+in+unsaturated+porous+media.">Modeling of biological clogging in unsaturated porous media.</a> J Contam Hydrol. 106, 39-50 (2009).</li><li>Kumar, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microscale+confinement+features+can+affect+biofilm+formation.">Microscale confinement features can affect biofilm formation.</a> Microfluid Nanofluid. 14, 895-902 (2013).</li><li>Neethirajan, S., et al., Bhushan, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Encylopedia of Nanotechnology. , (2012).</li><li>Barathi, S., Vasudevan, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Utilization+of+petroleum+hydrocarbons+by+Pseudomonas+fluorescens+isolated+from+a+petroleum-contaminated+soil.">Utilization of petroleum hydrocarbons by Pseudomonas fluorescens isolated from a petroleum-contaminated soil.</a> Environ Int. 26, 413-416 (2001).</li><li>Das, S., Kumar, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Formation+and+post-formation+dynamics+of+bacterial+biofilm+streamers+as+highly+viscous+liquid+jets.">Formation and post-formation dynamics of bacterial biofilm streamers as highly viscous liquid jets.</a> arXiv preprint arXiv:1312.6056. , (2013).</li><li>Shaw, T., Winston, M., Rupp, C. J., Klapper, I., Stoodley, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Commonality+of+elastic+relaxation+times+in+biofilms.">Commonality of elastic relaxation times in biofilms.</a> Phys Rev Lett. 93, (2004).</li><li>Berejnov, V., Djilali, N., Sinton, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Lab-on-chip+methodologies+for+the+study+of+transport+in+porous+media:+energy+applications.">Lab-on-chip methodologies for the study of transport in porous media: energy applications.</a> Lab Chip. 8, 689-693 (2008).</li></ol>

The authors have nothing to disclose.

We demonstrated a simple microfluidic device that mimics porous media for studying biofilm development in complex habitats. There are several critical steps that dictate the outcome of the experiments. They include device geometry. While the post geometry can vary, adequate pore-space for streamers to form is necessary. Moreover, Valiei et al.1 have demonstrated that streamer formation occurs only in a certain flow rate range. At flow rates lower than a threshold value, deformation of biofilms into st...

Recently, we demonstrated bacterial biofilm formation dynamics in a microfluidic device that mimics porous media1. Bacterial biofilms are essentially colonies of surface aggregated bacteria that are encased by extracellular polymeric substances (EPS)2-4. These thin films of bacteria can form in almost every conceivable niche ranging from smooth surfaces to the much more complex habitat of porous media. Valiei et al.1 used a microfluidic device with an array of micro-pillars to simulate a porous media structure and studied biofilm formation in this device as a function of fluid flow rate. They found that in a certain flow regime, filamentous biofilms known as streamers began to emerge between different pillars. Streamers can be tethered at one or both ends to solid surfaces, but the rest of the structure is suspended in liquid. Streamer formation typically starts after an initial layer of biofilm has formed and its formation can dictate the long-term evolution of biofilm in such complex habitats. Recently, several researchers have investigated the dynamics of streamer formation. Yazdi et al.5 showed that the streamers can form in vortical flows originating from an oscillating bubble. In another experiment, Rusconi et al.6 investigated the effect of channel curvature and channel geometry on the formation of streamers. They found that the streamers can form in curved sections of microchannels, and streamer morphology is related to motility. Recent research has demonstrated that streamers can have wide repercussions in various natural and artificial scenarios as they can act as precursors to the formation of mature structures in porous interfaces, lead to rapid and catastrophic biofilm proliferation in a biomedical systems, and also cause substantial flow-structure interactions, etc1,7-9.
Biofilm streamers often form in complex habitats such as porous media. Understanding biofilm growth in porous media environment is relevant to several environmental and industrial processes such as biological wastewater treatment10, maintaining well-bore integrity in situations such as CO2 capture11 and plugging of pores in soil12. Observing biofilm formation in such complex habitats can often be challenging due to the opacity of porous media. In such situations, microfluidics based porous media platforms can prove extremely advantageous as they allow real-time and in&#160;situ monitoring. Another advantage of microfluidics is the ability to build multiple bioreactors on a single bio-microfluidic platform and simultaneously allow for online monitoring and/or incorporation of sensors. The flexibility to implement multiple laboratory experiments in one device and the ability to collect significant pertinent data for accurate statistical analysis is an important advantage of microfluidic systems13,14.
In the context of the above discussion, understanding streamer formation dynamics in a porous media environment would be beneficial to several applications. In this study, we develop the protocol for investigating streamer formation in a device that mimics porous media. Fabrication of the microfluidic platform, necessary steps for cell culture and experimentation are described. In our experiments, the wild type bacterial strain of Pseudomonas fluorescens was employed. P. fluorescens, found naturally in soil, plays a key role in maintaining soil ecology15. The bacterial strain employed had been genetically engineered to express green fluorescent protein (GFP) constitutively.

<table border="0" cellpadding="0" cellspacing="0" width="1038">
	<tbody>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Name of Material/ Equipment</td>
			<td style="width:255px;">Company</td>
			<td style="width:119px;">Catalog Number</td>
			<td style="width:339px;">Comments/Description</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Flourescent Microscope</td>
			<td style="width:255px;">Nikon</td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">LB agar</td>
			<td style="width:255px;">Fisher</td>
			<td style="width:119px;">BP1425-500</td>
			<td>suspend 40 g in 1 L of purified water</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">LB broth</td>
			<td style="width:255px;">Fisher</td>
			<td style="width:119px;">BP1427-500</td>
			<td>suspend 20 g in 1 L of purified water</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Biosafety hood</td>
			<td style="width:255px;">Microzone corporation</td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Petri-dish</td>
			<td style="width:255px;">Fisher</td>
			<td style="width:119px;">875712</td>
			<td>sterile 100mmx15mm polystyrene petri dish</td>
		</tr>
		<tr height="23">
			<td height="23" style="height:23px;width:325px;">Incubator shaker</td>
			<td>New Brunswick Scientific</td>
			<td style="width:119px;"></td>
			<td style="width:339px;">Excella E24incubator shaker series</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;">50 mL sterilized centrifuge tube</td>
			<td style="width:255px;">Corning</td>
			<td style="width:119px;">430828</td>
			<td>Polypropylene Rnase-/Dnase-free</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Tetracycline free base</td>
			<td style="width:255px;">MP Biomedicals</td>
			<td style="width:119px;">103012</td>
			<td>50 ug/mL</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">SYLGARD 184 silicone</td>
			<td style="width:255px;">Dow Corning Corporation</td>
			<td style="width:119px;">68037-59-2</td>
			<td>Elastomer Base and curing agent</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Positive photoresist (AZ4620)</td>
			<td style="width:255px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:325px;">Plastic tube</td>
			<td style="width:255px;">Cole- Parmer</td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
	</tbody>
</table>

protocol for biofilm streamer formation in a microfluidic device with micro-pillars

Several bacterial species possess the ability to attach to surfaces and colonize them in the form of thin films called biofilms. Biofilms that grow in porous media are relevant to several industrial and environmental processes such as wastewater treatment and CO2 sequestration. We used Pseudomonas fluorescens, a Gram-negative aerobic bacterium, to investigate biofilm formation in a microfluidic device that mimics porous media. The microfluidic device consists of an array of micro-posts, which were fabricated using soft-lithography. Subsequently, biofilm formation in these devices with flow was investigated and we demonstrate the formation of filamentous biofilms known as streamers in our device. The detailed protocols for fabrication and assembly of microfluidic device are provided here along with the bacterial culture protocols. Detailed procedures for experimentation with the microfluidic device are also presented along with representative results.

Using the above mentioned microfabrication protocol, a PDMS based microfluidic device was constructed. Figure 1 shows the scanning electron microscope (SEM) images of the PDMS device. Figure 1a shows the entrance section of the device. A fork-like entrance is created to equalize pressure head across the device. Further SEM imaging also showed that the pillar walls are almost vertical (Figure&#160;1b). The cultured bacterial solution (Figure&#160;2) was d...

Watch this Scientific Journal Video about Protocol for Biofilm Streamer Formation in a Microfluidic Device with Micro-pillars at JoVE.com

Protocol for Biofilm Streamer Formation in a Microfluidic Device with Micro-pillars

Protocols for the study of biofilm formation in a microfluidic device that mimics porous media are discussed. The microfluidic device consists of an array of micro-pillars and biofilm formation by Pseudomonas fluorescens in this device is investigated.

Several bacterial species possess the ability to attach to surfaces and colonize them in the form of thin films called biofilms. Biofilms that grow in ...

protocol-for-biofilm-streamer-formation-microfluidic-device-with

Research

JoVE Journal

Bioengineering

12.1K Views.  University of Alberta. Protocols for the study of biofilm formation in a microfluidic device that mimics porous media are discussed. The microfluidic device consists of an array of micro-pillars and biofilm formation by Pseudomonas fluorescens in this device is investigated. 