Name: simple homemade tools to handle fruit flies—drosophila melanogaster
Uploaded: 2019-07-24T13:30:00.000+00:00
Duration: 8 min 28 s
Description: Watch this Scientific Journal Video about Simple Homemade Tools to Handle Fruit Fliesâ€”Drosophila melanogaster at JoVE.com

1. Preparing Tools and Accessories
<ol>
	<li>Tip/funnel stoppers
	<ol>
		<li>Obtain two sponge plugs (the diameter of the plugs must be slightly larger than the internal diameter of the vials used to transfer flies). Make a hole in the centers of the sponge plugs with a heated electric soldering iron.</li>
		<li>Obtain two 1 mL pipette tips, cut one in half transversely with a sharp knife, and discard the pointed end. Then, cut 1.5 cm of the pointed end off the second pipette tip. Glue the remains of the two pipette tips together with an all-purpose adhesive to make an elongated pipette tip (Figure 1A).</li>
		<li>Insert a funnel and the elongated pipette tip into the sponge plugs to make a tip and funnel stopper (hereafter referred to as T- and F-stoppers) and cap the pipette tip with a 100 &#956;L microcentrifuge tube (Figure 1A). 
		NOTE: The length of the funnel stem must be greater than the height of the plug. If it is shorter than or equal to the height of the plug, then flies will escape from the stem opening. The end of the funnel stem should be situated at least 2 cm above the surface of the culture medium or the bottom of an empty vial. Small funnels (e.g., disk diameter &#60;60 mm) with small internal stem opening diameters (&#60;5 mm) are preferable. Either a glass or a plastic funnel can be used to make an F-stopper. However, plastic funnels are preferable for biology classes, as they break less readily than glass funnels.</li>
	</ol>
	</li>
	<li>Microdissecting needles 
	<ol>
		<li>Obtain mechanical pencils that feel comfortable in the hand and insect pins that match the diameters (e.g., 0.5 mm, 0.7 mm) of their lead refills.</li>
		<li>Cut the wide ends of the insect pins with a pair of pliers and file the cut flat. Replace the lead with the pins (Figure 1B). Press the click button and feed out 0.5&#8211;1 cm of a pin to conduct a dissection. Clean the pin and push it completely back into the pencil shaft after a dissection activity to make it safe for any person to handle. 
		NOTE: Microdissecting needles are useful not only in dissections of organs such as larval salivary glands but also in counting and sorting dead adult flies.</li>
	</ol>
	</li>
	<li>Hard icepacks 
	<ol>
		<li>Obtain several refreezable hard icepacks (large-sized icepacks are preferable). Figure 1C shows an icepacks that worked well, which measures 26.5 cm x 14.5 cm x 2.5 cm and has top and bottom sides that are completely flat.</li>
		<li>Cut medical gauze (nonsterile) into pieces that are slightly smaller than the cold surfaces of the icepacks they cover. For example, a piece of medical gauze slightly smaller than 26.5 cm x 14.5 cm is preferable to cover an icepack shown in Figure 1C. 
		NOTE: The necessary accessories for these chilling tools include: an ice box (we used a 25 cm x 15 cm x 15 cm foam box for one person and 37 cm x 28 cm x 20 cm box for more than one person), which is used to store crushed ice; a pair of fine-point tweezers, which are used to grab chilled flies by their wings and transfer them to a vial; a pair of protective work gloves, which are used to take chilled icepacks out of a -20 &#176;C freezer; and plastic film, which is used to cover the stage of a stereomicroscope.</li>
	</ol>
	</li>
	<li>Drosophila egg collection cage 
	NOTE: Ready-made Drosophila egg collection cages are available from many biotechnology companies11. Described here is a small acrylic bottle-shaped egg collection cage for 60 mm Petri dishes (Figure 1D left; the cage design is shown in the middle). It can be adapted for other Petri dish sizes (e.g., 100 mm, 35 mm). This allows the transfer of flies into or out of the cage with ease. A simple cage can be prepared as follows.
	<ol>
		<li>Use a snap cutter to cut a soft plastic drink bottle (500 mL, internal diameter ca. 65 mm) into an approximate 2:1 (pointed end:blunt end) ratio and discard the blunt end.</li>
		<li>Wrap a strip of card paper around an apple juice plate (internal diameter 60 mm) with adhesive tape [the apple juice plate is used to collect eggs (Figure 1E, right)].</li>
	</ol>
	</li>
	<li>Cordless tube brush driver
	<ol>
		<li>Obtain a cordless drill driver (max speed = 500 rpm).</li>
		<li>Obtain a tube brush that has bristles along its sides as well as its front. Ideally, the diameter of the brush should be slightly larger than the diameter of the culture vials that need to be cleaned. Cut the end of its handle so it can be inserted into the drill chuck (Figure 1D). 
		NOTE: The necessary accessories for these cleaning tools include stainless steel sponges and long cuff rubber gloves.</li>
	</ol>
	</li>
</ol>
2. Transferring Adult Flies from Vial A to Vial B
NOTE: Transferring adult flies from one vial to another is the most common practice conducted in Drosophila experiments [e.g., transferring flies from old culture (A) to fresh culture (B) or from a cross vial (A) to empty vial (B)] for anesthetizing. The protocol described here can be used for any adult fly transferring activities. Unless otherwise stated, this protocol is used to transfer flies from vial A to vial B throughout this paper.
<ol>
	<li>Check the stem of the funnel of an F-stopper and the pipette tip of a T-stopper carefully, then clear any flies that remain in the stoppers with a rubber air blower. This step is of paramount importance, especially when one set of T- and F-stoppers is used for the continuous transferring of different Drosophila lines.</li>
	<li>Tap down the flies in vial A and replace its plug with a T-stopper, then plug vial B with an F-stopper.</li>
	<li>Invert vial A over vial B, insert the pipette tip end of the T-stopper into the funnel opening of the F-stopper, knock the edge of inverted vial A to allow flies to slip out of the pipette tip and through the stem of the funnel, and drop into vial B. If any old food in vial A becomes less compact, it may drop when vial A is inverted and knocked. In such a situation, invert vial B over vial A and allow the flies to crawl up into vial B.</li>
	<li>Separate the T-stopper from the F-stopper. Cap the pipette tip end of the T-stopper with a 200 &#956;L microcentrifuge tube if the remaining flies in vial A need to be transferred to other vials momentarily; otherwise, remove the T-stopper and replug vial A. Remove the F-stopper and replug vial B.</li>
</ol>
3. Immobilizing Flies by Chilling
<ol>
	<li>Keep hard refreezable icepacks in a -20 &#176;C freezer for at least 24 h before use.</li>
	<li>Place a chilled, hard icepack at room temperature (RT) for 20 min. Slightly moisten a piece of non-aseptic medical gauze with some running water and allow it to closely cling to the surface of the icepack. The medical gauze can be reused in the next fly chilling. At the same time, chill an empty vial in crushed ice.</li>
	<li>Transfer adult flies that need to be immobilized into the chilled empty vial (CEV). When the two transfer vials are separated, cover the CEV with a Petri dish or a plug and knock the CEV against the crushed ice to tap all the flies in the CEV down to the bottom. Repeat this process several times until all flies are immobilized. The flies will be immobilized within 30 s. Next, place the CEV in the ice for 1 min. It is not advisable to transfer too many flies at one time for anesthetizing.</li>
	<li>Pour the chilled flies out onto the medical gauze that covers the ice pack. Spread out the overlapping flies with a paintbrush and make sure that each fly can be chilled by the cold surface of the icepack. If a chilled hard icepack swells slightly, place it on a towel and work on its flat side.</li>
	<li>Remove the stage clips from the stereomicroscope, cover the stage with a piece of plastic film, and put the icepack onto the stage. Turn on the top light (a cold light source is desirable), focus the stereomicroscope and move the icepack until the chilled flies can be seen clearly.</li>
</ol>
4. Killing Adult Flies for Counting, Sorting, or Discarding
<ol>
	<li>Transfer adult flies into an empty vial and cover it with a Petri dish.</li>
	<li>Invert the vial, heat it for 1 min + 20 s in a microwave oven, and allow the dead flies drop into the Petri dish.</li>
	<li>Put on protective work gloves and take the vial out of the microwave. Pour the dead flies onto a white paper card, count or examine the flies with a microdissecting needle under a stereomicroscope, and dispose of the fly bodies in a garbage can after observation.</li>
	<li>To kill unwanted flies, heat the flies for 2&#8211;3 min in a microwave oven, then tap the carcasses into a garbage can. 
	NOTE: It is not advisable to kill some wing mutant strains (e.g., wing length mutants) for examination, as it is difficult to judge from the carcasses if the wings extend beyond the tip of the abdomen, which is seen in wild-type flies.</li>
</ol>
5. Transferring Flies In/Out of Bottle-shaped Egg Collection Cage
NOTE: As mentioned above, T- and F-stoppers are used to transfer flies into and out of the egg collection cage. Flies do not need to be anesthetized throughout this process. Other details, such as preparing the apple juice medium, egg collection, and dechorionization, can be found in the literature12.
<ol>
	<li>Insert the egg collection cage into the apple juice plate or mount the apple juice plate to the cage made of a soft drink bottle. Seal the joint around the two components with a strip of paraffin film.</li>
	<li>Place as many flies as possible into the cage and replug the cage with a foam stopper after transferring the flies.</li>
	<li>To change the food for flies in the cage, transfer the flies in the cage to an empty vial.</li>
	<li>Replace the apple juice plate and reseal it, then transfer the flies from the vial back to the cage.</li>
	<li>When egg collection ends, transfer the flies into an empty vial and transfer them into culture vials.</li>
</ol>
6. Cleaning Glass Culture Vials
NOTE: Generally, an old culture vial contains live flies. In the protocol described here, these flies DO NOT need to be killed before cleaning unless they are transgenic flies.
<ol>
	<li>Remove any permanent marker ink from the glass culture vials with wet, stainless steel sponges.</li>
	<li>Soak the culture vials in running water.
	<ol>
		<li>Fill a laboratory sink with water, add liquid dishwashing soap into the water, and mix.</li>
		<li>Immerse the culture vials into the water, then remove the plug, allowing the water to run into the vial. The dish detergent in the water will make any remaining adult flies sink to the bottom and drown in the water.</li>
		<li>Soak the old culture vials in water for at least 30 min.</li>
	</ol>
	</li>
	<li>Loosen the chuck of the drill, insert the test tube brush and retighten the chuck. Check the direction of the rotation selector and ensure that the drill rotates clockwise. Adjust the speed trigger and ensure that the maximum speed is less than 500 rpm.</li>
	<li>Clean the culture vials.
	<ol>
		<li>Clean the culture vials roughly.
		<ol>
			<li>Put a long cuff rubber glove on the non-dominant hand and hold the vial in the water.</li>
			<li>Hold the cordless tube brush driver with the bare dominant hand, squeeze the brush into the culture vial, and squeeze the trigger. 
			NOTE: Do not dip the battery into the water. The rotating brush will break up old food, pupa, etc., and remove more than 95% of the waste.</li>
			<li>Dump the waste into a separate garbage can. Repeat this process until most of the waste in each vial has been cleaned.</li>
		</ol>
		</li>
		<li>Clean the culture vials thoroughly.
		<ol>
			<li>Clean the tube brush, drain and clean the sink, and refill it with clean water.</li>
			<li>Remove the remaining waste from each culture vial as described in section 6.4.1.</li>
		</ol>
		</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Jennings, B. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Drosophila+&#8211;+a+versatile+model+in+biology+&#38;+medicine.">Drosophila &#8211; a versatile model in biology &#38; medicine.</a> Materials Today. 14 (5), 190-195 (2011).</li><li>JoVE Science Education Database. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Biology I: yeast, Drosophila and C. elegans. An Introduction to Drosophila melanogaster. , (2018).</li><li>Ashburner, M., Roote, J., Sullivan, W., Ashburner, M., Hawley, R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laboratory+Culture+of+Drosophila.">Laboratory Culture of Drosophila.</a> Drosophila Protocols. , (2000).</li><li>Greenspan, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fly+pushing:+The+theory+and+practice+of+Drosophila+genetics.">Fly pushing: The theory and practice of Drosophila genetics.</a> Cold Spring Harbor Laboratory Press. , (2004).</li><li>Ashburner, M., Thompson, J., Ashburner, M., Wright, T. R. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+laboratory+culture+of+Drosophila.">The laboratory culture of Drosophila.</a> The genetics and biology of Drosophila. 2a, 1-109 (1978).</li><li>Ratterman, D. M., O&#39;Donnell, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Eliminating+ether+by+using+ice+for+Drosophila+labs.">Eliminating ether by using ice for Drosophila labs.</a> Tested Studies For Laboratory Teaching. , 259-265 (2003).</li><li>. Culturing techniques for Drosophila Available from: <a target="_blank" href="https://www.ptbeach.com/cms/lib/NJ01000839/Centricity/Domain/113/ap%20biology%20Labs/Culturing%20techniques%20for%20Drosophila.pdf">https://www.ptbeach.com/cms/lib/NJ01000839/Centricity/Domain/113/ap%20biology%20Labs/Culturing%20techniques%20for%20Drosophila.pdf</a> (2019)</li><li>Markow, T. A., O&#39;Grady, P. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Drosophila: A Guide to Species Identification and Use. , (2006).</li><li>Artiss, T., Hughes, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Taking+the+Headaches+Out+of+Anesthetizing+Drosophila:+A+Cheap+&#38;+Easy+Method+of+Constructing+Carbon+Dioxide+Staging.">Taking the Headaches Out of Anesthetizing Drosophila: A Cheap &#38; Easy Method of Constructing Carbon Dioxide Staging.</a> The American Biology Teacher. 69 (8), e77-e80 (2007).</li><li>Qu, W. -. H., Zhu, T. -. B., Yang, D. -. X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Modified+Cooling+Method+and+its+Application+in+Drosophila+Experiments.">A Modified Cooling Method and its Application in Drosophila Experiments.</a> Journal Of Biological Education. 49 (3), 302-308 (2015).</li><li>. Egg-laying cages for drosophila Available from: <a target="_blank" href="https://www.kisker-biotech.com/frontoffice/product?produitId=0H-19-17">https://www.kisker-biotech.com/frontoffice/product?produitId=0H-19-17</a> (2018)</li><li>Roberts, D. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Drosophila: a practical approach. , (1998).</li><li>Tang, M., Peng, Q. -. F., Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two+devices+for+Drosophila+experiments+(in+Chinese).">Two devices for Drosophila experiments (in Chinese).</a> Bulletin of Biology. 45 (11), 49-50 (2010).</li><li>Zhou, T. -. y., Gan, J., Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+of+sponge+plug+and+sponge+plug+based+fly+transferring+device+for+Drosophila+experiments+(in+Chinese).">Preparation of sponge plug and sponge plug based fly transferring device for Drosophila experiments (in Chinese).</a> Bulletin of Biology. 46 (6), 49-50 (2011).</li><li>Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Genetics laboratory investigation. , (2016).</li><li>Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Carnivory+in+the+larvae+of+Drosophila+melanogaster+and+other+Drosophila+species.">Carnivory in the larvae of Drosophila melanogaster and other Drosophila species.</a> Scientific Reports. 8, (2018).</li><li>Stocker, H., Gallant, P., Dahmann, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Getting+Started:+An+Overview+on+Raising+and+Handling+Drosophila.">Getting Started: An Overview on Raising and Handling Drosophila.</a> Drosophila: Methods and Protocols. , (2008).</li></ol>

The author have nothing to disclose.

Some homemade tools for handling basic activities involved in Drosophila rearing and experimentation are described in this paper. These tools are simple but rather effective. Virtually, any lab can make these tools with ease, and a research or a teaching laboratory does not need to find a ready-made alternative that is perhaps not available locally.
Fly transferring is the most common practice and a difficult task in Drosophila experiments. Unfortunately, until now, there hav...

The fruit fly, Drosophila melanogaster, is a model organism widely used in biological research and biology education to study a wide range of topics1,2. The basic problems of handling Drosophila are the transfer of adults from vial to vial and immobilization of the flies so they are easier to handle, as all adults (except for some mutants3,4) can fly.
Conventionally, a researcher transfers flies from one vial to another by holding two vials mouth-to-mouth, tapping the flies down or allowing flies to fly up into another vial, then separating and replugging both vials4. Obviously, this requires that the opening of two vials with the same diameter, and it is hard to control the quantity of flies transferred. Meanwhile, this requires quick hands to get the job done, and escaping stray flies can result in problems for the laboratory or classroom. Adding extra virgin flies or male flies to an already prepared cross is another routine task in Drosophila experiments. Conventionally, flies must be immobilized in the cross vial before the addition of extra flies.
Adult Drosophila are routinely anaesthetized by ether, CO2, or chilling5. Compared to ether and CO2 exposure, chilling is the most cost-efficient agent for immobilizing adult Drosophila and the least harmful to both the flies and researchers (especially young students)6,7. However, water that condenses continuously on the cold surface or chamber wets the flies. It is difficult to determine the phenotypes of wet flies, and they can easily become damaged during manipulation8,9. This has kept the chilling method from becoming more widely accepted.
Tools for fly transferal and a method for fly cooling have been previously described10. Herein, a modified chilling anesthesia technique is reported that is safe, reliable, and feasible for Drosophila experiments. Also described in this paper are 1) methods for killing adults for counting, sorting, or discarding, 2) labor-saving devices and protocols for cleaning glass culture vials, and 3) a simple cage for collecting eggs. The easily designed and cost-effective tools described here can be used to address the difficult issues of fly handling, and these methods have been tested and are proven to be robust, reliable, and easy-to-handle for experienced and novice researchers.

<table><tbody><tr><td>A pair of pliers</td><td></td><td></td><td></td></tr><tr><td>Cordless drill driver</td><td></td><td></td><td>max speed: 500 rpm</td></tr><tr><td>Electric soldering iron</td><td></td><td></td><td></td></tr><tr><td>File</td><td></td><td></td><td></td></tr><tr><td>Funnel</td><td></td><td></td><td>diameter of disk&amp;lt;60mm</td></tr><tr><td>Ice box</td><td></td><td></td><td></td></tr><tr><td>Insect pins</td><td></td><td></td><td></td></tr><tr><td>Infrared thermometer</td><td></td><td></td><td>HCIYET HT-830</td></tr><tr><td>Long cuff rubber gloves</td><td></td><td></td><td></td></tr><tr><td>Mechanical pencils</td><td></td><td></td><td></td></tr><tr><td>Medical gauze</td><td></td><td></td><td></td></tr><tr><td>Microcentrifuge tube</td><td></td><td></td><td>100 ul</td></tr><tr><td>Microwave oven</td><td></td><td></td><td></td></tr><tr><td>Parafilm</td><td></td><td></td><td></td></tr><tr><td>Peri dish</td><td></td><td></td><td>internal diameter 60 mm</td></tr><tr><td>Pipette tips</td><td></td><td></td><td>1 ml</td></tr><tr><td>Plastic film</td><td></td><td></td><td></td></tr><tr><td>Plastic Peri dish</td><td></td><td></td><td>&amp;Phi;36 mm used to cover the empty vial</td></tr><tr><td>Point tweezers</td><td></td><td></td><td></td></tr><tr><td>Protective work gloves</td><td></td><td></td><td></td></tr><tr><td>Re-freezable hard icepacks</td><td></td><td></td><td>26.5&amp;times;14.5&amp;times;2.5 cm or larger</td></tr><tr><td>Rubber air blower</td><td></td><td></td><td></td></tr><tr><td>Snap cutter</td><td></td><td></td><td></td></tr><tr><td>Soft drink bottle</td><td></td><td></td><td>500 ml, internal diameter c.a. 65 mm</td></tr><tr><td>Sponge stopper</td><td></td><td></td><td></td></tr><tr><td>Stainless steel sponges</td><td></td><td></td><td></td></tr><tr><td>Tube brush</td><td></td><td></td><td></td></tr><tr><td>Vial</td><td></td><td></td><td>&amp;Phi;34 mm &amp;times; 90 mm</td></tr></tbody></table>

simple homemade tools to handle fruit flies&#8212;drosophila melanogaster

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in practice, as adult flies fly. Demonstrated here is how to make some simple and cost-effective tools to address difficult issues in the handling of Drosophila. Holes in foam stoppers are made and pipette tips or funnels are inserted into the holes. Flies then move only in one direction into the pipette tip/funnel assemblage, allowing efficient control of the transfer of adult Drosophila into or out of a vial. Existing protocols have been modified for cool-anesthetizing flies by chilling in crushed ice and transferring them onto a cold, hard icepack surface. The icepack is covered with a piece of medical gauze that keeps immobilized flies from the condensed water when examined under a stereomicroscope. The flies are finally euthanized for counting and sorting or discarded by microwaving. A bottle-shaped cage has also been developed for collecting eggs, as well as a labor-saving device and accompanying protocol for cleaning glass culture vials.

The T- and F-stoppers were developed as a set of simple tools that can be adapted and used in any fly transferring activities. Transferring flies from an old culture into several fresh cultures involves removing the plugs of the fresh vials, replacing them with F-stoppers, then tapping down the flies in the old vial, quickly removing its plug, and replacing it with a T-stopper. If the old food is compact, then it is important to flip the old vial and insert the tip of T-stopper into the o...

Watch this Scientific Journal Video about Simple Homemade Tools to Handle Fruit Fliesâ€”Drosophila melanogaster at JoVE.com

Simple Homemade Tools to Handle Fruit Flies&#8212;Drosophila melanogaster

Described here is the use of several homemade tools to transfer, chill, and kill adult Drosophila, as well as to clean glass culture vials and collect eggs. These tools are easy to make and are rather efficient in handling Drosophila.

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in ...

simple-homemade-tools-to-handle-fruit-fliesdrosophila-melanogaster

Research

JoVE Journal

Biology

15.8K Views.  China Agricultural University. Described here is the use of several homemade tools to transfer, chill, and kill adult Drosophila, as well as to clean glass culture vials and collect eggs. These tools are easy to make and are rather efficient in handling Drosophila.

Video: Simple Homemade Tools to Handle Fruit Flies—Drosophila melanogaster

Studying Aggression in Drosophila (fruit flies)

Aggression is an innate behavior that evolved in the framework of defending or obtaining resources. This complex social behavior is influenced by genetic, hormonal and environmental factors. In many organisms, aggression is critical to survival but controlling and suppressing aggression in distinct contexts also has become increasingly important. In recent years, invertebrates have become increasingly useful as model systems for investigating the genetic and systems biological basis of complex social behavior. This is in part due to the diverse repertoire of behaviors exhibited by these organisms. In the accompanying video, we outline a method for analyzing aggression in Drosophila whose design encompasses important eco-ethological constraints. Details include steps for: making a fighting chamber; isolating and painting flies; adding flies to the fight chamber; and video taping fights. This approach is currently being used to identify candidate genes important in aggression and in elaborating the neuronal circuitry that underlies the output of aggression and other social behaviors.

Studying Aggression in Drosophila fruit flies

Aggression is an innate behavior that evolved in the framework of defending or obtaining resources.  This complex social behavior is influenced by ...

Rearing the Fruit Fly Drosophila melanogaster Under Axenic and Gnotobiotic Conditions

The influence of microbes on myriad animal traits and behaviors has been increasingly recognized in recent years. The fruit fly Drosophila melanogaster is a model for understanding microbial interactions with animal hosts, facilitated by approaches to rear large sample sizes of Drosophila under microorganism-free (axenic) conditions, or with defined microbial communities (gnotobiotic). This work outlines a method for collection of Drosophila embryos, hypochlorite dechorionation and sterilization, and transfer to sterile diet. Sterilized embryos are transferred to sterile diet in 50 ml centrifuge tubes, and developing larvae and adults remain free of any exogenous microbes until the vials are opened. Alternatively, flies with a defined microbiota can be reared by inoculating sterile diet and embryos with microbial species of interest. We describe the introduction of 4 bacterial species to establish a representative gnotobiotic microbiota in Drosophila. Finally, we describe approaches for confirming bacterial community composition, including testing if axenic Drosophila remain bacteria-free into adulthood.

Rearing the Fruit Fly Drosophila melanogaster Under Axenic and Gnotobiotic Conditions

A method for rearing Drosophila melanogaster under axenic and gnotobiotic conditions is presented. Fly embryos are dechorionated in sodium hypochlorite, transferred aseptically to sterile diet, and reared in closed containers. Inoculating diet and embryos with bacteria leads to gnotobiotic associations, and bacterial presence is confirmed by plating whole-body Drosophila homogenates.

The influence of microbes on myriad animal traits and behaviors has been increasingly recognized in recent years. The fruit fly Drosophila melanogaster is ...

Developmental Biology

Operant Learning of Drosophila at the Torque Meter

For experiments at the torque meter, flies are kept on standard fly medium at 25&deg;C and 60% humidity with a 12hr light/12hr dark regime. A standardized breeding regime assures proper larval density and age-matched cohorts. Cold-anesthetized flies are glued with head and thorax to a triangle-shaped hook the day before the experiment. Attached to the torque meter via a clamp, the fly's intended flight maneuvers are measured as the angular momentum around its vertical body axis. The fly is placed in the center of a cylindrical panorama to accomplish stationary flight. An analog to digital converter card feeds the yaw torque signal into a computer which stores the trace for later analysis. The computer also controls a variety of stimuli which can be brought under the fly's control by closing the feedback loop between these stimuli and the yaw torque trace. Punishment is achieved by applying heat from an adjustable infrared laser.

Measuring the yaw torque of tethered Drosophila with the torque meter allows the neuroscientist exquisite control of the stimulus situation of the experimental animal. Together with the unique genetic tools available in the fruit fly, this paradigm is used for a wide variety of neurobiological research.

For experiments at the torque meter, flies are kept on standard fly medium at 25&deg;C and 60% humidity with a 12hr light/12hr dark regime. A standardized ...

A Direct and Simple Method to Assess Drosophila melanogaster's Viability from Embryo to Adult

In Drosophila melanogaster, viability assays are used to determine the fitness of certain genetic backgrounds. Allelic variations can result in partial or complete loss of viability at different stages of development. Our lab has developed a method to assess viability in Drosophila from embryo to fully mature adult. The method relies on quantifying the number of progeny present at different stages during development, starting with hatched embryos. After embryos have been quantified, additional stages are counted, including L1/L2, pupae, and mature adults. After all stages have been examined, a statistical analysis such as the chi-square test is used to determine if there is a significant difference between the starting number of progeny (hatched embryos) and later stages culminating in the observed number of adults, thus rejecting or accepting the null hypothesis (that the number of hatched embryos will be equal to the number of larvae, pupae, and adults recorded throughout the stages of development). The primary advantage of this assay is its simplicity and accuracy, as it does not require an embryo rinse to transfer them to the food vial, avoiding losses from technical errors. Although the protocol described here does not directly examine L2/L3 larvae, additional steps can be added to account for these. Comparing the number of hatched embryos, L1, pupae, and adults can help determine if viability was compromised during the L2/L3 stages for further studies (the use of colored food helps with visual identification of larvae). Overall, this method can help Drosophila researchers and educators determine when viability is compromised during the fly life cycle. Routine assessment of stocks using this assay can prevent accumulation of secondary mutations that may affect the phenotype of the originally isolated mutant, especially if the original mutations affect fitness. For this reason, our lab maintains multiple copies of each of our Dm ime4 alleles and routinely checks the purity of each stock with this method in addition to other molecular analyses.&#160;

A Direct and Simple Method to Assess Drosophila melanogaster's Viability from Embryo to Adult

This protocol is designed to assess the viability of Drosophila at every developmental stage, from embryo to adult. The method can be used to determine and compare the viability of different genotypes or growth conditions.

In Drosophila melanogaster, viability assays are used to determine the fitness of certain genetic backgrounds. Allelic variations can result in partial or ...

An Affordable and Efficient "Homemade" Platform for Drosophila Behavioral Studies, and an Accompanying Protocol for Larval Mitochondrial Respirometry

The usefulness of Drosophila as a model organism for the study of human diseases, behaviors and basic biology is unquestionable. Although practical, Drosophila research lacks popularity in developing countries, possibly due to the misinformed idea that establishing a lab and performing relevant experiments with such tiny insects is difficult and requires expensive, specialized apparatuses. Here, we describe how to build an affordable flylab to quantitatively analyze a myriad of behavioral parameters in D. melanogaster, by 3D-printing many of the necessary pieces of equipment. We provide protocols to build in-house vial racks, courtship arenas, apparatuses for locomotor assays, etc., to be used for general fly maintenance and to perform behavioral experiments using adult flies and larvae. We also provide protocols on how to use more sophisticated systems, such as a high resolution oxygraph, to measure mitochondrial oxygen consumption in larval samples, and show its association with behavioral changes in the larvae upon the xenotopic expression of the mitochondrial alternative oxidase (AOX). AOX increases larval activity and mitochondrial leak respiration, and accelerates development at low temperatures, which is consistent with a thermogenic role for the enzyme. We hope these protocols will inspire researchers, especially from developing countries, to use Drosophila to easily combine behavior and mitochondrial metabolism data, which may lead to information on genes and/or environmental conditions that may also regulate human physiology and disease states.

An Affordable and Efficient "Homemade" Platform for Drosophila Behavioral Studies, and an Accompanying Protocol for Larval Mitochondrial Respirometry

We provide protocols for anyone with a "maker culture" mind to start building a flylab for quantitative analysis of a myriad of behavioral parameters in Drosophila melanogaster, by 3D-printing many of the necessary pieces of equipment. We also describe a high resolution respirometry protocol using larvae to combine behavioral and mitochondrial metabolism data.

The usefulness of Drosophila as a model organism for the study of human diseases, behaviors and basic biology is unquestionable. Although practical, ...

Behavior

Experimental Protocol for Using Drosophila As an Invertebrate Model System for Toxicity Testing in the Laboratory

Emergent properties and external factors (population-level and ecosystem-level interactions, in particular) play important roles in mediating ecologically-important endpoints, though they are rarely considered in toxicological studies. D. melanogaster is emerging as a toxicology model for the behavioral, neurological, and genetic impacts of toxicants, to name a few. More importantly, species in the genus Drosophila can be utilized as a model system for an integrative framework approach to incorporate emergent properties and answer ecologically-relevant questions in&#160;toxicology research. The aim of this paper is to provide a protocol for exposing species in the genus Drosophila to pollutants to be used as a model system for a range of phenotypic outputs and ecologically-relevant questions. More specifically, this protocol can be used to 1) link multiple biological levels of organization and understand the impact of toxicants on both individual- and population-level fitness; 2) test the impact of toxicants at different stages of developmental exposure; 3) test multigenerational and evolutionary implications of pollutants; and 4) test multiple contaminants and stressors simultaneously.

Experimental Protocol for Using Drosophila As an Invertebrate Model System for Toxicity Testing in the Laboratory

In this paper, we provide a detailed protocol for exposing species in the genus Drosophila to pollutants with the goal of studying the impact of exposure on a range of phenotypic outputs at different developmental stages and for more than one generation.

Emergent properties and external factors (population-level and ecosystem-level interactions, in particular) play important roles in mediating ...

Circadian Entrainment of Drosophila Melanogaster

Nearly universal among organisms, circadian rhythms coordinate biological activity to earth&#39;s orbit around the sun. To identify factors creating this rhythm and to understand the resulting outputs, entrainment of model organisms to defined circadian time-points is required. Here we detail a procedure to entrain many Drosophila to a defined circadian rhythm. Furthermore, we detail post-entrainment steps to prepare samples for immunofluorescence, nucleic acid, or protein extraction-based analysis.

Here, we detail how to synchronize Drosophila to a circadian day. This is the first, and most important step necessary for studying biological rhythms and chronobiology.

Nearly universal among organisms, circadian rhythms coordinate biological activity to earth&#39;s orbit around the sun. To identify factors creating this ...

Methods for Rearing the Parasitoid Ganaspis brasiliensis, a Promising Biological Control Agent for the Invasive Drosophila suzukii

Native to East Asia, the spotted-wing drosophila, Drosophila suzukii (Matsumura) (Diptera: Drosophilidae), has established widely in the Americas, Europe, and parts of Africa over the last decade, becoming a devastating pest of various soft-skinned fruits in its invaded regions. Biological control, especially by means of self-perpetuating and specialized parasitoids, is expected to be a viable option for sustainable area-wide management of this highly mobile and polyphagous pest. Ganaspis brasiliensis Ihering (Hymenoptera: Figitidae) is a larval parasitoid that is widely distributed in East Asia, and has been found to be one of the most effective parasitoids of D. suzukii.
Following rigorous pre-introduction evaluations of its efficacy and potential non-target risks, one of the more host-specific genetic groups of this species (G1 G. brasiliensis) has been approved recently for introduction and field release in the United States and Italy. Another genetic group (G3 G. brasiliensis), which was also commonly found to attack D. suzukii in East Asia, may be considered for introduction in the near future. There is currently enormous interest in rearing G. brasiliensis for research or in mass-production for field release against D. suzukii. This protocol and associated video article describe effective rearing methods for this parasitoid, both on a small scale for research and a large scale for mass-production and field release. These methods may benefit further long-term research and use of this Asian-native parasitoid as a promising biological control agent for this global invasive pest.

Methods for Rearing the Parasitoid Ganaspis brasiliensis, a Promising Biological Control Agent for the Invasive Drosophila suzukii

Ganaspis brasiliensis-a larval parasitoid of Drosophila suzukii (a global invasive fruit crop pest)-has been approved or is considered for introduction into Europe and the United States for biological control of this pest. This article provides protocols for both small-scale and large-scale rearing of this parasitoid.

Native to East Asia, the spotted-wing drosophila, Drosophila suzukii (Matsumura) (Diptera: Drosophilidae), has established widely in the Americas, Europe, ...

Drosophila Maintenance

Drosophila melanogaster, commonly known as fruit flies, are a frequently used model organism for life science research. Although starting a collection of these critters may seem as easy as leaving a banana on your kitchen counter for too long, a productive fly colony in the lab requires careful husbandry and maintenance.
This video demonstrates the necessary steps for maintaining a healthy fly stock. The overview begins with the preparation and storage of the yeast and sugar-containing media on which flies feed. Next, the vessels most commonly used for housing Drosophila are shown, as well as how and when to move flies between these containers. Finally, the presentation also includes examples of the ways in which housing and feeding conditions are manipulated for biological experiments.

Maintenance and Husbandry of Drosophila melanogaster

Drosophila melanogaster, commonly known as fruit flies, are a frequently used model organism for life science research. Although starting a collection of ...

Education

JoVE Science Education

Basic Biology

Biology I: yeast, Drosophila and C. elegans

Drosophila melanogaster Embryo and Larva Harvesting and Preparation

Drosophila melanogaster embryos and larvae are easy to manipulate and develop rapidly by mechanisms that are analogous to other organisms, including mammals. For these reasons, many researchers utilize fly embryos and larvae to answer questions in diverse fields ranging from behavioral to developmental biology. Prior to experimentation, however, the embryos and larvae must first be collected.
This video will first demonstrate how "egg-laying cups" are used to collect Drosophila embryos on agar plates. The harvest and dechorionation of embryos will then be described. Next, the video will demonstrate how to identify and manipulate Drosophila in one of the three larval stages that follow the embryo stage. Finally, examples of some of the ways in which fly embryos and larvae are used in biological research are provided.

Drosophila melanogaster Embryo and Larva Harvesting and Preparation

Drosophila melanogaster embryos and larvae are easy to manipulate and develop rapidly by mechanisms that are analogous to other organisms, including ...

Simple Homemade Tools to Handle Fruit Flies—Drosophila melanogaster

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Studying Aggression in Drosophila (fruit flies)

Rearing the Fruit Fly Drosophila melanogaster Under Axenic and Gnotobiotic Conditions

Operant Learning of Drosophila at the Torque Meter

A Direct and Simple Method to Assess Drosophila melanogaster's Viability from Embryo to Adult

An Affordable and Efficient "Homemade" Platform for Drosophila Behavioral Studies, and an Accompanying Protocol for Larval Mitochondrial Respirometry

Experimental Protocol for Using Drosophila As an Invertebrate Model System for Toxicity Testing in the Laboratory

Circadian Entrainment of Drosophila Melanogaster

Methods for Rearing the Parasitoid Ganaspis brasiliensis, a Promising Biological Control Agent for the Invasive Drosophila suzukii

Drosophila Maintenance

Drosophila melanogaster Embryo and Larva Harvesting and Preparation