Research reported in this publication was supported by the National Institute of Arthritis and Musculoskeletal and Skin Diseases under award number R01AR051912. The content is solely the responsibility of the authors and does not necessarily represent the official views of the National Institutes of Health (NIH).

The authors have no conflicts of interest.

The technique described here overcomes several disadvantages associated with conventional techniques for assessing shoulder motion (i.e., cadaveric simulations, 2D imaging, static 3D imaging, video-based motion capture systems, wearable sensors, etc.) by providing accurate measures of 3D joint motion during dynamic activities. The accuracy of the protocol described herein was established for the glenohumeral joint against the gold standard of radiostereometric analysis (RSA) to be &#177;0.5&#176; and &#177;0.4 mm<sup cla...

The shoulder is one of the human body&#39;s most complex joint systems, with motion occurring through the coordinated actions of four individual joints, multiple ligaments, and approximately 20 muscles. The shoulder also has the greatest range of motion of the body&#39;s major joints and is often described as a compromise between mobility and stability. Unfortunately, shoulder pathologies are common, resulting in substantial pain, disability, and decreased quality of life. For example, rotator cuff tears affect about 40% of the population over age 601,2,3, with approximately 250,000 rotator cuff repairs performed annually4, and an estimated economic burden of $3-5 billion per year in the United States5. Additionally, shoulder dislocations are common and are often associated with chronic dysfunction6. Lastly, glenohumeral joint osteoarthritis (OA) is another significant clinical problem involving the shoulder, with population studies indicating that roughly 15%-20% of adults over the age of 65 have radiographic evidence of glenohumeral OA7,8. These conditions are painful, impair activity levels, and decrease quality of life.
Although the pathogeneses of these conditions are not fully understood, it is generally accepted that altered shoulder motion is associated with many shoulder pathologies9,10,11. Specifically, abnormal joint motion may contribute to the pathology9,12, or that the pathology may lead to abnormal joint motion13,14. Relationships between joint motion and pathology are likely complex, and subtle alterations in joint motion may be important in the shoulder. For example, although angular motion is the predominant motion occurring at the glenohumeral joint, joint translations also occur during shoulder motion. Under normal conditions these translations likely do not exceed several millimeters15,16,17,18,19, and therefore may be below the level of in-vivo accuracy for some measurement techniques. While it may be tempting to assume that small deviations in joint motion may have little clinical impact, it is important to also recognize that the cumulative effect of subtle deviations over years of shoulder activity may exceed the individual&#39;s threshold for tissue healing and repair. Furthermore, in-vivo forces at the glenohumeral joint are not inconsequential. Using custom instrumented glenohumeral joint implants, previous studies have shown that raising a 2 kg weight to head height with an outstretched arm can result in glenohumeral joint forces that can range from 70% to 238% of body weight20,21,22. Consequently, the combination of subtle changes in joint motion and high forces concentrated over the glenoid&#39;s small load-bearing surface area may contribute to the development of degenerative shoulder pathologies.
Historically, the measurement of shoulder motion has been accomplished through a variety of experimental approaches. These approaches have included the use of complex cadaveric testing systems designed to simulate shoulder motion23,24,25,26,27, video-based motion capture systems with surface markers28,29,31, surface-mounted electromagnetic sensors32,33,34,35, bone pins with reflective markers or other sensors attached36,37,38, static two-dimensional medical imaging (i.e., fluoroscopy39,40,41 and radiographs17,42,43,44,45), static three-dimensional (3D) medical imaging using MRI46,47, computed tomography48, and dynamic, 3D single plane fluoroscopic imaging49,50,51. More recently, wearable sensors (e.g., inertial measurement units) have gained popularity for measuring shoulder motion outside the laboratory setting and in free-living conditions52,53,54,55,56,57.
In recent years, there has been a proliferation of biplane radiographic or fluoroscopic systems designed to accurately measure dynamic, 3D in-vivo motions of the shoulder58,59,60,61,62. The purpose of this article is to describe the authors&#39; approach for measuring shoulder motion using a custom biplanar videoradiography system. The specific objectives of this article are to describe the protocols to acquire biplanar videoradiographic images of the shoulder complex, acquire CT scans, develop 3D bone models, locate anatomical landmarks, track the position and orientation of the humerus, scapula, and torso from the biplanar radiographic images, and calculate kinematic outcome measures.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Calibration cube</td>
			<td>Built in-house</td>
			<td>N/A</td>
			<td>10 cm Lucite box with a tantalum bead in each corner and four additional beads midway along the box&#8217;s vertical edges (12 beads total). The positions of each bead are precisely known relative to a corner of the box that serves as the origin of the laboratory coordinate system.</td>
		</tr>
		<tr>
			<td>Distortion correction grid</td>
			<td>Built in-house</td>
			<td>N/A</td>
			<td>Lucite sheet that covers the entire face of the 16 inch image intensifier and contains an orthogonal array of tantalum beads spaced at 1 cm.</td>
		</tr>
		<tr>
			<td>ImageJ</td>
			<td>National Institutes of Health</td>
			<td>N/A</td>
			<td>Image processing software used to prepare TIFF stack of bone volumes.</td>
		</tr>
		<tr>
			<td>Markerless Tracking Workbench</td>
			<td>Custom, in house software</td>
			<td>N/A</td>
			<td>A workbench of custom software used to digitize anatomical landmarks on 3D bone models, constructs anatomical coordinate systems, uses intensity-based image registration to perform markerless tracking, and calculates and visualize kinematic outcomes measures.</td>
		</tr>
		<tr>
			<td>MATLAB</td>
			<td>Mathworks, Inc</td>
			<td>N/A</td>
			<td>Computer programming software. For used to perform data processing and analysis.</td>
		</tr>
		<tr>
			<td>Mimics (version 20)</td>
			<td>Materialise, Inc</td>
			<td>N/A</td>
			<td>Image processing software used to segment humerus, scapula, and ribs from CT scan.</td>
		</tr>
		<tr>
			<td>Open Inventor</td>
			<td>Thermo Fisher Scientific</td>
			<td>N/A</td>
			<td>3D graphics program used to visualize bones</td>
		</tr>
		<tr>
			<td>Phantom Camera Control (PCC) software (version 3.4)</td>
			<td></td>
			<td>N/A</td>
			<td>Software for specifying camera parameters, and acquiring and saving radiographic images</td>
		</tr>
		<tr>
			<td>Pulse generator (Model 9514)</td>
			<td>Quantum Composers, Inc.</td>
			<td>N/A</td>
			<td>Syncs the x-ray and camera systems and specifies the exposure time</td>
		</tr>
		<tr>
			<td>Two 100 kW pulsed x-ray generators (Model CPX 3100CV)</td>
			<td>EMD Technologies</td>
			<td>N/A</td>
			<td>Generates the x-rays used to produce radiographic images</td>
		</tr>
		<tr>
			<td>Two 40 cm image intensifiers (Model P9447H110)</td>
			<td>North American Imaging</td>
			<td>N/A</td>
			<td>Converts x-rays into photons to produce visible image</td>
		</tr>
		<tr>
			<td>Two Phantom VEO 340 cameras</td>
			<td>Vision Research</td>
			<td>N/A</td>
			<td>High speed cameras record the visible image created by the x-ray system</td>
		</tr>
	</tbody>
</table>

measuring 3d in-vivo shoulder kinematics using biplanar videoradiography

The shoulder is one of the human body's most complex joint systems, with motion occurring through the coordinated actions of four individual joints, multiple ligaments, and approximately 20 muscles. Unfortunately, shoulder pathologies (e.g., rotator cuff tears, joint dislocations, arthritis) are common, resulting in substantial pain, disability, and decreased quality of life. The specific etiology for many of these pathologic conditions is not fully understood, but it is generally accepted that shoulder pathology is often associated with altered joint motion. Unfortunately, measuring shoulder motion with the necessary level of accuracy to investigate motion-based hypotheses is not trivial. However, radiographic-based motion measurement techniques have provided the advancement necessary to investigate motion-based hypotheses and provide a mechanistic understanding of shoulder function. Thus, the purpose of this article is to describe the approaches for measuring shoulder motion using a custom biplanar videoradiography system. The specific objectives of this article are to describe the protocols to acquire biplanar videoradiographic images of the shoulder complex, acquire CT scans, develop 3D bone models, locate anatomical landmarks, track the position and orientation of the humerus, scapula, and torso from the biplanar radiographic images, and calculate the kinematic outcome measures. In addition, the article will describe special considerations unique to the shoulder when measuring joint kinematics using this approach.

A 52-year-old asymptomatic female (BMI = 23.6 kg/m2) was recruited as part of a previous investigation and underwent motion testing (coronal plane abduction) on her dominant (right) shoulder65. Prior to data collection, the participant provided written informed consent. The investigation was approved by Henry Ford Health System&#39;s Institutional Review Board. Data collection was performed using the protocol previously described (Figure 3).
<p class="j...

Watch this Scientific Journal Video about Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography at JoVE.com

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Biplane videoradiography can quantify shoulder kinematics with a high degree of accuracy. The protocol described herein was specifically designed to track the scapula, humerus, and the ribs during planar humeral elevation, and outlines the procedures for data collection, processing, and analysis. Unique considerations for data collection are also described.

The shoulder is one of the human body's most complex joint systems, with motion occurring through the coordinated actions of four individual joints, ...

measuring-3d-vivo-shoulder-kinematics-using-biplanar

Research

Education

JoVE Core

JoVE Journal

Anatomy and Physiology

Bioengineering

Unit 1

The Joints

SCIENTISTS IN ACTION

2.9K Views.  Henry Ford Health System. Biplane videoradiography can quantify shoulder kinematics with a high degree of accuracy. The protocol described herein was specifically designed to track the scapula, humerus, and the ribs during planar humeral elevation, and outlines the procedures for data collection, processing, and analysis. Unique considerations for data collection are also described.

Video: Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Measuring the Mechanical Properties of Living Cells Using Atomic Force Microscopy

Mechanical properties of cells and extracellular matrix (ECM) play important roles in many biological processes including stem cell differentiation, tumor formation, and wound healing. Changes in stiffness of cells and ECM are often signs of changes in cell physiology or diseases in tissues. Hence, cell stiffness is an index to evaluate the status of cell cultures. Among the multitude of methods applied to measure the stiffness of cells and tissues, micro-indentation using an Atomic Force Microscope (AFM) provides a way to reliably measure the stiffness of living cells. This method has been widely applied to characterize the micro-scale stiffness for a variety of materials ranging from metal surfaces to soft biological tissues and cells. The basic principle of this method is to indent a cell with an AFM tip of selected geometry and measure the applied force from the bending of the AFM cantilever. Fitting the force-indentation curve to the Hertz model for the corresponding tip geometry can give quantitative measurements of material stiffness. This paper demonstrates the procedure to characterize the stiffness of living cells using AFM. Key steps including the process of AFM calibration, force-curve acquisition, and data analysis using a MATLAB routine are demonstrated. Limitations of this method are also discussed.

This paper demonstrates a protocol to characterize the mechanical properties of living cells by means of microindentation using an Atomic Force Microscope (AFM).

Mechanical  properties of cells and extracellular matrix (ECM) play important roles in many  biological processes including stem cell differentiation, ...

Fabrication and Implantation of Miniature Dual-element Strain Gages for Measuring In Vivo Gastrointestinal Contractions in Rodents.

Gastrointestinal dysfunction remains a major cause of morbidity and mortality. Indeed, gastrointestinal (GI) motility in health and disease remains an area of productive research with over 1,400 published animal studies in just the last 5 years. Numerous techniques have been developed for quantifying smooth muscle activity of the stomach, small intestine, and colon. In vitro and ex vivo techniques offer powerful tools for mechanistic studies of GI function, but outside the context of the integrated systems inherent to an intact organism. Typically, measuring in vivo smooth muscle contractions of the stomach has involved an anesthetized preparation coupled with the introduction of a surgically placed pressure sensor, a static pressure load such as a mildly inflated balloon or by distending the stomach with fluid under barostatically-controlled feedback. Yet many of these approaches present unique disadvantages regarding both the interpretation of results as well as applicability for in vivo use in conscious experimental animal models. The use of dual element strain gages that have been affixed to the serosal surface of the GI tract has offered numerous experimental advantages, which may continue to outweigh the disadvantages. Since these gages are not commercially available, this video presentation provides a detailed, step-by-step guide to the fabrication of the current design of these gages. The strain gage described in this protocol is a design for recording gastric motility in rats. This design has been modified for recording smooth muscle activity along the entire GI tract and requires only subtle variation in the overall fabrication. Representative data from the entire GI tract are included as well as discussion of analysis methods, data interpretation and presentation.

Fabrication and Implantation of Miniature Dual-element Strain Gages for Measuring In Vivo Gastrointestinal Contractions in Rodents.

The in vivo measurement of smooth muscle contractions along the gastrointestinal tract of laboratory animals remains a powerful, though underutilized, technique. Flexible, dual element strain gages are not commercially available and require fabrication. This protocol describes the construction of reliable, inexpensive strain gages for acute or chronic implantation in rodents.

Gastrointestinal dysfunction remains a major cause of morbidity and mortality. Indeed, gastrointestinal (GI) motility in health and disease remains an ...

Using Adhesive Patterning to Construct 3D Paper Microfluidic Devices

We demonstrate the use of patterned aerosol adhesives to construct both planar and nonplanar 3D paper microfluidic devices. By spraying an aerosol adhesive through a metal stencil, the overall amount of adhesive used in assembling paper microfluidic devices can be significantly reduced. We show on a simple 4-layer planar paper microfluidic device that the optimal adhesive application technique and device construction style depends heavily on desired performance characteristics. By moderately increasing the overall area of a device, it is possible to dramatically decrease the wicking time and increase device success rates while also reducing the amount of adhesive required to keep the device together. Such adhesive application also causes the adhesive to form semi-permanent bonds instead of permanent bonds between paper layers, enabling single-use devices to be non-destructively disassembled after use. Nonplanar 3D origami devices also benefit from the semi-permanent bonds during folding, as it reduces the likelihood that unrelated faces may accidently stick together. Like planar devices, nonplanar structures see reduced wicking times with patterned adhesive application vs uniformly applied adhesive.

We demonstrate the use of patterned aerosol adhesives to construct 3D paper microfluidic devices. This method of adhesive application forms semi-permanent bonds between layers, enabling single-use devices to be non-destructively disassembled after use and to ease folding complex nonplanar structures.

We demonstrate the use of patterned aerosol adhesives to construct both planar and nonplanar 3D paper microfluidic devices. By spraying an aerosol ...

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo

Historically, most cellular processes have been studied in only 2 dimensions. While these studies have been informative about general cell signaling mechanisms, they neglect important cellular cues received from the structural and mechanical properties of the local microenvironment and extracellular matrix (ECM). To understand how cells interact within a physiological ECM, it is important to study them in the context of 3 dimensional assays. Cell migration, cell differentiation, and cell proliferation are only a few processes that have been shown to be impacted by local changes in the mechanical properties of a 3-dimensional ECM. Collagen I, a core fibrillar component of the ECM, is more than a simple structural element of a tissue. Under normal conditions, mechanical cues from the collagen network direct morphogenesis and maintain cellular structures. In diseased microenvironments, such as the tumor microenvironment, the collagen network is often dramatically remodeled, demonstrating altered composition, enhanced deposition and altered fiber organization. In breast cancer, the degree of fiber alignment is important, as an increase in aligned fibers perpendicular to the tumor boundary has been correlated to poorer patient prognosis1. Aligned collagen matrices result in increased dissemination of tumor cells via persistent migration2,3. The following is a simple protocol for embedding cells within a 3-dimensional, fibrillar collagen hydrogel. This protocol is readily adaptable to many platforms, and can reproducibly generate both aligned and random collagen matrices for investigation of cell migration, cell division, and other cellular processes in a tunable, 3-dimensional, physiological microenvironment.

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo

Collagen is a core component of the ECM, and provides essential cues for several cellular processes ranging from migration to differentiation and proliferation. Provided here is a protocol for embedding cells within 3D collagen hydrogels, and a more advanced technique for generating randomized or aligned collagen matrices using PDMS microchannels.

Historically, most cellular processes have been studied in only 2 dimensions.  While these studies have been informative about general cell signaling ...

Quantification of Strain in a Porcine Model of Skin Expansion Using Multi-View Stereo and Isogeometric Kinematics

Tissue expansion is a popular technique in plastic and reconstructive surgery that grows skin in vivo for correction of large defects such as burns and giant congenital nevi. Despite its widespread use, planning and executing an expansion protocol is challenging due to the difficulty in measuring the deformation imposed at each inflation step and over the length of the procedure. Quantifying the deformation fields is crucial, as the distribution of stretch over time determines the rate and amount of skin grown at the end of the treatment. In this manuscript, we present a method to study tissue expansion in order to gain quantitative knowledge of the deformations induced during an expansion process. This experimental protocol incorporates multi-view stereo and isogeometric kinematic analysis in a porcine model of tissue expansion. Multi-view stereo allows three-dimensional geometric reconstruction from uncalibrated sequences of images. The isogeometric kinematic analysis uses splines to describe the regional deformations between smooth surfaces with few mesh points. Our protocol has the potential to bridge the gap between basic scientific inquiry regarding the mechanics of skin expansion and the clinical setting. Eventually, we expect that the knowledge gained with our methodology will enable treatment planning using computational simulations of skin deformation in a personalized manner.

This protocol uses multi-view stereo to generate three-dimensional (3D) models out of uncalibrated sequences of photographs, making it affordable and adjustable to a surgical setting. Strain maps between the 3D models are quantified with spline-based isogeometric kinematics, which facilitate representation of smooth surfaces over coarse meshes sharing the same parameterization.

Tissue expansion is a popular technique in plastic and reconstructive surgery that grows skin in vivo for correction of large defects such as burns and ...

Bioprinting of Cartilage and Skin Tissue Analogs Utilizing a Novel Passive Mixing Unit Technique for Bioink Precellularization

Bioprinting is a powerful technique for the rapid and reproducible fabrication of constructs for tissue engineering applications. In this study, both cartilage and skin analogs were fabricated after bioink pre-cellularization utilizing a novel passive mixing unit technique. This technique was developed with the aim to simplify the steps involved in the mixing of a cell suspension into a highly viscous bioink. The resolution of filaments deposited through bioprinting necessitates the assurance of uniformity in cell distribution prior to printing to avoid the deposition of regions without cells or retention of large cell clumps that can clog the needle. We demonstrate the ability to rapidly blend a cell suspension with a bioink prior to bioprinting of both cartilage and skin analogs. Both tissue analogs could be cultured for up to 4 weeks. Histological analysis demonstrated both cell viability and deposition of tissue specific extracellular matrix (ECM) markers such as glycosaminoglycans (GAGs) and collagen I respectively.

Cartilage and skin analogs were bioprinted using a nanocellulose-alginate based bioink. The bioinks were cellularized prior to printing via a single step passive mixing unit. The constructs were demonstrated to be uniformly cellularized, have high viability, and exhibit favorable markers of differentiation.

Bioprinting is a powerful technique for the rapid and reproducible fabrication of constructs for tissue engineering applications. In this study, both ...

Rigid Embedding of Fixed and Stained, Whole, Millimeter-Scale Specimens for Section-free 3D Histology by Micro-Computed Tomography

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in every tissue to be identified and characterized. Our laboratory is actively working to make technological advances in X-ray micro-computed tomography (micro-CT) that will bring the diagnostic power of histology to the study of full tissue volumes at cellular resolution (i.e., an X-ray Histo-tomography modality). Toward this end, we have made targeted improvements to the sample preparation pipeline. One key optimization, and the focus of the present work, is a straightforward method for rigid embedding of fixed and stained millimeter-scale samples. Many of the published methods for sample immobilization and correlative micro-CT imaging rely on placing the samples in paraffin wax, agarose, or liquids such as alcohol. Our approach extends this work with custom procedures and the design of a 3-dimensional printable apparatus to embed the samples in an acrylic resin directly into polyimide tubing, which is relatively transparent to X-rays. Herein, sample preparation procedures are described for the samples from 0.5 to 10 mm in diameter, which would be suitable for whole zebrafish larvae and juveniles, or other animals and tissue samples of similar dimensions. As proof of concept, we have embedded the specimens from Danio, Drosophila, Daphnia, and a mouse embryo; representative images from 3-dimensional scans for three of these samples are shown. Importantly, our methodology leads to multiple benefits including rigid immobilization, long-term preservation of laboriously-created resources, and the ability to re-interrogate samples.

We developed protocols and designed a custom apparatus to enable embedding of millimeter-scale specimens. We present sample preparation procedures with an emphasis on embedding in acrylic resin and polyimide tubing to achieve rigid immobilization and long-term storage of specimens for the interrogation of tissue architecture and cell morphology by micro-CT.

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in ...

Rat Model of Adhesive Capsulitis of the Shoulder

This proposal aims to create an in vivo rat model of adhesive capsulitis for researching potential treatment options for this condition and other etiologies of comparable arthrofibrosis. The model includes extra-articular fixation of the shoulder in rats via scapular to humeral suturing, resulting in a secondary contracture without invading the intra-articular space and resulting in decreased rotational ROM and increased joint stiffness.
We used 10 Sprague-Dawley rats for the purpose of this study. Baseline ROM measurements were taken before glenohumeral immobilization. The rats were subjected to 8 weeks of immobilization before the fixation sutures were removed and changes in ROM and joint stiffness were evaluated. To evaluate whether immobilization resulted in a significant reduction in ROM, changes in kinematics were calculated. ROM was measured at each time point in the follow-up period and was compared to the baseline internal and external ROM measurements. In order to evaluate the stiffness, joint kinetics were calculated by determining the differences in torque (text and tint ) needed to reach the initial external rotation of 60&#176; and initial internal rotation of 80&#176;.
After the removal of the extra-articular suture fixation on follow-up day 0, we found a 63% decrease in total ROM compared to baseline. We observed continuous improvement until week 5 of follow-up, with the progress slowing down around a 19% restriction. On week 8 of follow-up, there was still an 18% restriction of ROM. Additionally, on follow-up day 0, we found the torque increased by 13.3 Nmm when compared to baseline. On week 8, the total torque was measured to be 1.4 &#177; 0.2 Nmm higher than initial measurements. This work introduces a rat model of shoulder adhesive capsulitis with lasting reduced ROM and increased stiffness.

This protocol presents an in vivo rat model of adhesive capsulitis. The model includes an internal fixation of the glenohumeral joint with extra-articular suture fixation for an extended time, resulting in a decreased rotational range of motion (ROM) and increased joint stiffness.

This proposal aims to create an in vivo rat model of adhesive capsulitis for researching potential treatment options for this condition and other ...

Measuring Global Cellular Matrix Metalloproteinase and Metabolic Activity in 3D Hydrogels

Three-dimensional (3D) cell culture systems often more closely recapitulate in vivo cellular responses and functions than traditional two-dimensional (2D) culture systems. However, measurement of cell function in 3D culture is often more challenging. Many biological assays require retrieval of cellular material which can be difficult in 3D cultures. One way to address this challenge is to develop new materials that enable measurement of cell function within the material. Here, a method is presented for measurement of cellular matrix metalloproteinase (MMP) activity in 3D hydrogels in a 96-well format. In this system, a poly(ethylene glycol) (PEG) hydrogel is functionalized with a fluorogenic MMP cleavable sensor. Cellular MMP activity is proportional to fluorescence intensity and can be measured with a standard microplate reader. Miniaturization of this assay to a 96-well format reduced the time required for experimental set up by 50% and reagent usage by 80% per condition as compared to the previous 24-well version of the assay. This assay is also compatible with other measurements of cellular function. For example, a metabolic activity assay is demonstrated here, which can be conducted simultaneously with MMP activity measurements within the same hydrogel. The assay is demonstrated with human melanoma cells encapsulated across a range of cell seeding densities to determine the appropriate encapsulation density for the working range of the assay. After 24 h of cell encapsulation, MMP and metabolic activity readouts were proportional to cell seeding density. While the assay is demonstrated here with one fluorogenic degradable substrate, the assay and methodology could be adapted for a wide variety of hydrogel systems and other fluorescent sensors. Such an assay provides a practical, efficient and easily accessible 3D culturing platform for a wide variety of applications.

Here, a protocol is presented for encapsulating and culturing cells in poly(ethylene glycol) (PEG) hydrogels functionalized with a fluorogenic matrix metalloproteinase (MMP)-degradable peptide. Cellular MMP and metabolic activity are measured directly from the hydrogel cultures using a standard microplate reader.

Three-dimensional (3D) cell culture systems often more closely recapitulate in vivo cellular responses and functions than traditional two-dimensional (2D) ...

Four-Dimensional CT Analysis Using Sequential 3D-3D Registration

Four-dimensional computed tomography (4DCT) provides a series of volume data and visualizes joint motions. However, numerical analysis of 4DCT data remains difficult because segmentation in all volumetric frames is time-consuming. We aimed to analyze joint kinematics using a sequential 3D-3D registration technique to provide the kinematics of the moving bone with respect to the fixed bone semiautomatically using 4DCT DICOM data and existing software. Surface data of the source bones are reconstructed from 3DCT. The trimmed surface data are respectively matched with surface data from the first frame in 4DCT. These trimmed surfaces are sequentially matched until the last frame. These processes provide positional information for target bones in all frames of the 4DCT. Once the coordinate systems of the target bones are decided, translation and rotation angles between any two bones can be calculated. This 4DCT analysis offers advantages in kinematic analyses of complex structures such as carpal or tarsal bones. However, fast or large-scale motions cannot be traced because of motion artifacts.

We analyzed joint kinematics from four-dimensional computed tomography data. The sequential 3D-3D registration method semiautomatically provides the kinematics of the moving bone with respect to the subject bone from four-dimensional computed tomography data.

Four-dimensional computed tomography (4DCT) provides a series of volume data and visualizes joint motions. However, numerical analysis of 4DCT data ...