This work was funded by the COMET Centre &#34;ASSIC-Austrian Smart Systems Integration Research Center&#34;. ASSIC is co-funded by the BMK, the BMDW, and the Austrian provinces of Carinthia and Styria within the COMET-Competence Centres for Excellent Technologies programme of the Austrian Research Promotion Agency (FFG).

1. 3D printing
<ol>
	<li>Slicer settings
	<ol>
		<li>Open all &#34;.stl&#34; files with the slicer software and place the sensor parts on the platform (see Supplemental File 1, Supplemental File 2, Supplemental File 3, Supplemental File 4, Supplemental File 5, and Supplemental File 6).</li>
		<li>For a good printing result, tilt all the parts with respect to the platform.</li>
		<li>Generate support points with a density of 0.8 and a point size of 0.4 mm.</li>
		<li>Select Clear V4 with a layer thickness of 50 &#181;m.</li>
	</ol>
	</li>
	<li>Start printing.
	<ol>
		<li>Upload the slicer output file on the 3D printer.</li>
		<li>Look for the printing time and resin volumes that are displayed on the screen. Insert the clear V4 tank and resin cartridge, attach the mounting platform, and open the cartridge lid. Press Start on the printer.</li>
	</ol>
	</li>
	<li>Immediate post-processing
	<ol>
		<li>After the print is finished, open the printer and detach the mounting platform. 
		NOTE: This step can only be delayed if it is sure that the model will stay under the UV protection screen of the printer (see critical steps/print post-processing in the discussion).</li>
		<li>Gently peel all parts from the platform and place them in an isopropanol bath.</li>
		<li>Move the parts constantly for 20 min.</li>
		<li>Take out the parts every 5 min and flush all small gaps and holes thoroughly.</li>
	</ol>
	</li>
	<li>UV-hardening
	<ol>
		<li>Dry the parts before starting the hardening process.</li>
		<li>Flush all small gaps and holes with pressurized air.</li>
		<li>Place the parts into the UV hardening device and harden them for 50 min at 40 &#176;C. 
		NOTE: This setting differs from the manufacturer&#39;s recommended drying time and temperature (see critical steps/print post-processing in the discussion).</li>
	</ol>
	</li>
	<li>Post-processing
	<ol>
		<li>Check that all the cavities and holes are open.</li>
		<li>If a path is clogged, drill or scrape it with the straight grinder.</li>
		<li>Check that all the printed parts fit properly and that the copper tubes can be inserted. If they can&#39;t, then sand them down.</li>
	</ol>
	</li>
</ol>
2. Electrode manufacturing
<ol>
	<li>Measure 9 mm from the top of the 18 mm and 22 mm copper pipes and mark thesepositions.</li>
	<li>Cut the pipes with the pipe cutter at the markings. 
	NOTE: Make sure not to use too much force during the process. It takes several turns to cut through the pipes (see critical steps/electrode manufacturing in the discussion section).</li>
	<li>Deburr the copper ring carefully. Do not put too much pressure on the copper ring while deburring and try not to scratch the electrode surface. 
	NOTE: This is a very critical part and affects the performance of the sensor (see critical steps/electrode manufacturing and modifications/electrodes in the discussion section).</li>
	<li>Electrode soldering
	<ol>
		<li>Solder the red cable to the inner copper ring (18 mm) and the black cable to the outer copper ring (22 mm).</li>
		<li>Polish the copper ring to get rid of the oxidized copper layer on the surface.</li>
		<li>Clamp the ring in a vice.</li>
		<li>Pre-tin both the copper ring and the cable and solder the cable to the ring. 
		CAUTION: Due to the soldering, the copper electrodes heat up to 400 &#176;C. Only touch the electrodes with tweezers and wear thermo-protective gloves.</li>
	</ol>
	</li>
</ol>
3. Assembly
<ol>
	<li>Mix the two components of the epoxy glue in a tray. 
	NOTE: It is very important to use transparent glue to differentiate between soot bridges and hardened glue. 
	CAUTION: Work under a fume hood, wear protective clothes (especially gloves), and clean work surfaces. Further safety instructions can be found in the safety data sheet. Health hazard: &#34;Skin Corr. 1C - H314 Eye Dam. 1 - H318 Skin Sens. 1 - H317&#34;.</li>
	<li>Stick the inner electrode holder into the flow channel and wait 60 min for the glue to harden (Figure 7A).</li>
	<li>Place the inner electrode ring (18 mm) on the holder and guide the cable through the cable channel (Figure 7B). 
	NOTE: Make sure that there is enough space for the soldering point.</li>
	<li>Place the spacer around the inner electrode. 
	NOTE: This is a very critical step. If the distance between the electrodes is not exactly 1 mm everywhere in the entire sensor, the electric field, and subsequently the sensor performance, can be influenced (see critical steps/electrode manufacturing in the discussion).</li>
	<li>Place the outer electrode ring (22&#160;mm) on the holder and feed the cable through the cable channel (Figure 7C).</li>
	<li>Glue the outer electrode holder onto the flow channel. Insert the spacer into the gap between the two copper electrodes. Wait 60 min for the glue to harden (Figure 7D).</li>
	<li>Seal all the cable channels with epoxy glue. Wait overnight for the glue to cure.</li>
	<li>Insert the vacuum seal in the printed valve of the outer electrode. Insert the two sensor sides into each other and fasten them with the vacuum clamp (Figure 7E,F).</li>
</ol>
4. Tests
<ol>
	<li>Open the vacuum clamp of the sensor.</li>
	<li>Pull the two halves of the sensor apart and remove the seal.</li>
	<li>From there, touch the electrode ring with one multimeter probe tip, and the end of the cable leading to the electrode with the other multimeter tip.</li>
	<li>Pretests
	<ol>
		<li>Test the electrical connection of the electrode and the cable with the multimeter. Check whether the resistance is &#60;2 &#8486; (depending on the level of oxidation).</li>
		<li>Plug the hose onto the aerosol inlet and outlet and test if the sensor is airtight with the vacuum pump.</li>
	</ol>
	</li>
	<li>Parallel experiment
	<ol>
		<li>Build the sensor setup, according to Figure 8.
		<ol>
			<li>Connect the high-voltage power supply to the red sensor cable (high-voltage electrode).</li>
			<li>Connect the black sensor cable to the bench multimeter voltage input.</li>
			<li>Connect the electrometer ground (GND) with the power supply GND.</li>
			<li>Connect the multimeter USB cable to the PC.</li>
		</ol>
		</li>
		<li>Incorporate the sensor into the aerosol measurement setup. according to Figure 9.</li>
		<li>Aerosol generator
		<ol>
			<li>Gas supplies: Turn on the sheath flow, nitrogen, and propane supply (pressure needed: nitrogen, 4 bar; other gases, 1 bar each).</li>
			<li>Power source: Plug in the 24 V source cable for the built-in MFCs and connect the USB to the PC.</li>
			<li>Software: open the MFC software and insert the correct COM port number. Search for devices: if five devices are displayed (for five different MFCs), click stop searching. Input the starting conditions according to the aerosol generator&#39;s user manual: 10 mL/min propane, 1.55 L/min oxidation air, 7 L/min quench gas, 20 L/min dilution air.</li>
			<li>Start the aerosol generator (see Table of Materials) by turning the ON-OFF knob. When the knob is turned on, the nitrogen indicator is on, indicating all flow paths are open. Hold the flame-safety device and press the ignite button on the aerosol generator; observe a flame in the combustion chamber window. Release the flame-safety device after ~60 s very slowly.</li>
			<li>Enter the following mass flows: 60 mL/min propane, 1.55 L/min oxidation air, 7 L/min nitrogen (quench), and 20 L/min dilution air to set the correct size distribution parameters. 
			CAUTION: Connect the generator to the rest of the setup only if measurements are to be taken within the next minutes; otherwise, the filters of the dilution bridge will clog rapidly.</li>
		</ol>
		</li>
		<li>Connect the dilution bridge to the aerosol generator. Disconnect it once again and divert the aerosol flow to the fume hood until the start of the experiment. Make sure that the dilution bridge is closed before starting the experiment.</li>
		<li>Connect the dilution bridge outlet to the aerosol mixer inlet.</li>
		<li>Connect the aerosol mixer outlet 2 (see Figure 9E) to the sensor inlet.</li>
		<li>Incorporate the MFC.
		<ol>
			<li>Connect a high-efficiency particulate absorbing (HEPA) filter to the sensor outlet and connect the sensor outlet to the MFC inlet.</li>
			<li>Connect the power supply of the MFC and connect the USB to the PC.</li>
		</ol>
		</li>
		<li>Open the MFC software and input the correct COM port number.
		<ol>
			<li>Search for devices.</li>
			<li>Click stop searching?.</li>
			<li>Input the mass flow as 1 L/min.</li>
		</ol>
		</li>
		<li>Reference instrument (see Table of Materials)
		<ol>
			<li>Connect the LAN cable to the PC and open a connection to the IP address of the reference instrument in the browser to open a java application to control the reference instrument.</li>
			<li>In the reference instrument control software, press lock resources | stand by to start the pump. 
			NOTE: The heating process takes ~20 min.</li>
			<li>After the warm-up phase, click measurement to measure the aerosol entering the reference instrument.</li>
			<li>Choose a dilution ratio of 1:10 on the reference instrument.</li>
			<li>Use a y-fitting to connect the aerosol mixer outlet 1 (see Figure 9D) and the dilution airflow to the split end of the y-fitting (see Figure 9C), and connect the single end of the y-fitting to the reference instrument inlet. 
			NOTE: These two flows are then combined at the single end of the y-fitting.</li>
		</ol>
		</li>
		<li>Start of experiment
		<ol>
			<li>Connect the aerosol generator to the dilution bridge once again and make sure the dilution bridge is closed.</li>
			<li>Click measure on the reference instrument.</li>
			<li>Slowly open the dilution bridge until the desired aerosol mass concentration of 3-5 mg/m3 is reached, and start logging data on the reference instrument.</li>
			<li>Observe the reference instrument particle mass concentration. When the aerosol source is stable, switch on the sensor power supply at 1,000 V and start logging the data. 
			NOTE: If the concentration is not stable, see troubleshooting in the discussion section.</li>
		</ol>
		</li>
		<li>Collect data from the bench multimeter with a read command on the console or an automated script. 
		NOTE: After the sensor current stabilizes (approximately 5 min), a comparison of the reference instrument with the sensor current is possible. 
		CAUTION: If the sensor current increases rapidly above 10-7 A (corresponding to 0.1 V with an internal resistance of 1 M&#8486;), switch off the high voltage source (see troubleshooting in the discussion section).</li>
		<li>Parallel measurement: After the sensor reaches equilibrium, measure a concentration gradient in steps from 5 mg/m3 to 0.2 mg/m3 by adjusting the dilution bridge accordingly. 
		NOTE: When higher concentrations are used, the dilution ratio of the reference instrument must be increased.</li>
	</ol>
	</li>
	<li>Clean the sensor with pressurized air and a swab before each new measurement.</li>
</ol>
5. Field application
<ol>
	<li>Build the sensor setup, according to Figure 8.
	<ol>
		<li>Connect the high-voltage power supply to the red sensor cable (high voltage electrode).</li>
		<li>Connect the black sensor cable to the bench multimeter voltage input.</li>
		<li>Connect the electrometer GND with the power supply GND.</li>
		<li>Connect the multimeter USB cable to the PC.</li>
	</ol>
	</li>
	<li>Incorporate the sensor setup into the new measurement setup, according to Figure 10, and connect the aerosol source with the sensor.</li>
	<li>Split the outflowing particle stream from the aerosol source into path A) sensor setup and path B) ventilation.
	<ol>
		<li>MFC or pump: Use an MFC to pass the sample through the sensor.</li>
		<li>Use a HEPA filter upstream of the MFC. Connect the power supply of the MFC and connect the USB to the PC.</li>
		<li>Follow step 4.5.8 for parallel measurement.</li>
	</ol>
	</li>
	<li>Start of field experiment: Make sure that the aerosol source is connected to the sensor input.</li>
	<li>Switch on the sensor power supply and start logging data.</li>
</ol>
<img alt="Figure 8" class="xfigimg" src="/files/ftp_upload/64844/64844fig08.jpg" /> 
Figure 8: Sensor setup. A diagram of the sensor setup. Aerosol flows through the sensor. The sensor is connected to the voltmeter and a high-voltage supply. The voltmeter is controlled by a control unit that logs the sensor data. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig08large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 9" class="xfigimg" src="/files/ftp_upload/64844/64844fig09.jpg" /> 
Figure 9: Experimental plan for sensor evaluation. A stable aerosol source is used to mimic a particle source. The outflowing particle stream is split into path (A), sensor setup; and path (B), ventilation, enters the dilution bridge, and is further distributed to an aerosol mixer. After the mixer, the aerosol stream is split between a reference instrument path (D), which measures parallel to the sensor. This reference instrument needs dilution air, which is distributed through path (C). Path (E): an MFC draws air through the sensor. This MFC is protected from the aerosol stream with a HEPA filter. Abbreviations: MFC = mass flow controller; HEPA filter = high-efficiency particle absorbing filter. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig09large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 10" class="xfigimg" src="/files/ftp_upload/64844/64844fig10.jpg" /> 
Figure 10: Field test: the experimental plan. In this setup, an aerosol source is measured. The outflowing particle stream is split into path A) sensor setup and path B) ventilation and then enters the sensor. In this setup, an MFC with a HEPA filter upstream sucks the aerosol through the sensor. Abbreviations: MFC = mass flow controller; HEPA filter = high-efficiency particle absorbing filter. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig10large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

<ol>
	<li>World Health Organization. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Health+Effects+of+Particulate+Matter:+Policy+Implications+for+Countries+in+Eastern+Europe,+Caucasus+and+Central+Asia.">Health Effects of Particulate Matter: Policy Implications for Countries in Eastern Europe, Caucasus and Central Asia.</a> World Health Organization. , (2013).</li><li>Giechaskiel, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Review+of+motor+vehicle+particulate+emissions+sampling+and+measurement:+From+smoke+and+filter+mass+to+particle+number.">Review of motor vehicle particulate emissions sampling and measurement: From smoke and filter mass to particle number.</a> Journal of Aerosol Science. 67, 48-86 (2014).</li><li>Giechaskiel, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurement+of+automotive+nonvolatile+particle+number+emissions+within+the+European+legislative+framework:+a+review.">Measurement of automotive nonvolatile particle number emissions within the European legislative framework: a review.</a> Aerosol Science and Technology. 46 (7), 719-749 (2012).</li><li>Bainschab, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measuring+sub-23+nanometer+real+driving+particle+number+emissions+using+the+portable+DownToTen+sampling+system.">Measuring sub-23 nanometer real driving particle number emissions using the portable DownToTen sampling system.</a> Journal of Visualized Experiments. (159), e61287 (2020).</li><li>Wang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel+optical+instrument+for+estimating+size+segregated+aerosol+mass+concentration+in+real+time.">A novel optical instrument for estimating size segregated aerosol mass concentration in real time.</a> Aerosol Science and Technology. 43 (9), 939-950 (2009).</li><li>Axmann, H., Bergmann, A., Eichberger, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurement+of+ultrafine+exhaust+particles+using+light+scattering.">Measurement of ultrafine exhaust particles using light scattering.</a> 2013 Seventh International Conference on Sensing Technology (ICST). IEEE. , 937-941 (2013).</li><li>Berm&#250;dez, V., Luj&#225;n, J. M., Serrano, J. R., Pla, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transient+particle+emission+measurement+with+optical+techniques.">Transient particle emission measurement with optical techniques.</a> Measurement Science and Technology. 19 (6), 065404 (2008).</li><li>Michelsen, H. A., Schulz, C., Smallwood, G. J., Will, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laser-induced+incandescence:+Particulate+diagnostics+for+combustion,+atmospheric,+and+industrial+applications.">Laser-induced incandescence: Particulate diagnostics for combustion, atmospheric, and industrial applications.</a> Progress in Energy and Combustion Science. 51, 2-48 (2015).</li><li>Giechaskiel, B., Cresnoverh, M., J&#246;rgl, H., Bergmann, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Calibration+and+accuracy+of+a+particle+number+measurement+system.">Calibration and accuracy of a particle number measurement system.</a> Measurement Science and Technology. 21 (4), 045102 (2010).</li><li>Kulkarni, P., Baron, P. A., Willeke, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Aerosol Measurement: Principles, Techniques, and Applications. , (2011).</li><li>Agarwal, J. K., Sem, G. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Continuous+flow,+single-particle-counting+condensation+nucleus+counter.">Continuous flow, single-particle-counting condensation nucleus counter.</a> Journal of Aerosol Science. 11 (4), 343-357 (1980).</li><li>Bilby, D., Kubinski, D. J., Maricq, M. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Current+amplification+in+an+electrostatic+trap+by+soot+dendrite+growth+and+fragmentation:+Application+to+soot+sensors.">Current amplification in an electrostatic trap by soot dendrite growth and fragmentation: Application to soot sensors.</a> Journal of Aerosol Science. 98, 41-58 (2016).</li><li>Warey, A., Hall, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Performance+characteristics+of+a+new+on-board+engine+exhaust+particulate+matter+sensor.">Performance characteristics of a new on-board engine exhaust particulate matter sensor.</a> SAE Transactions. 114 (14), 1489-1497 (2005).</li><li>Maricq, M. M., Bilby, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+impact+of+voltage+and+flow+on+the+electrostatic+soot+sensor+and+the+implications+for+its+use+as+a+diesel+particulate+filter+monitor.">The impact of voltage and flow on the electrostatic soot sensor and the implications for its use as a diesel particulate filter monitor.</a> Journal of Aerosol Science. 124, 41-53 (2018).</li><li>Diller, T. T., Hall, M. J., Matthews, R. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Further+development+of+an+electronic+particulate+matter+sensor+and+its+application+to+diesel+engine+transients.">Further development of an electronic particulate matter sensor and its application to diesel engine transients.</a> SAE Technical Paper. , (2008).</li></ol>

The author is employed by Silicon Austria Labs and is a student of the Technical University Graz. There are no other conflicts of interest to declare.

Critical steps 
Print post-processing 
Almost any step in this protocol can be paused or postponed, except for post-processing of the freshly printed 3D parts (protocol step 1.5). If the UV protection screen of the printer is opened, the post-processing should begin immediately, otherwise the small cable channels, as well as the cavity for the seal, will clog. The precision fit of the cavity ensures that the sensor can be sealed airtight. This is important because the sensor is very sensitive to flow fluctuations. The hardening process is also important (protocol step 1.4); if the temperature is set too high, the material becomes too brittle and can break under the forces exerted by the clamp onto the outer electrode holder.
Electrode manufacturing 
Careful cutting and deburring (protocol steps 2.2-2.3) of the electrodes is very important because irregularities in the electrode gap cause perturbations in the electrical and velocity fields, which leads to poor sensor performance. In the worst-case scenario, a strong irregularity can cause the electrodes to come so close that the breakdown voltage is exceeded, and a short circuit occurs. From this point on, no statement can be made about the measurement signal and the measurement electronics are prone to damage.
Assembly 
Assembly of the sensor (protocol steps 3.4-3.6) is crucial, as this creates the electrode gap. As mentioned above, the distance between the electrodes is very important; this gap must be uniformly 1 mm over the entire length. These steps are important because they can change the electric field in the sensor drastically. The overall deposition behavior, as well as dendrite formation, can be influenced by the change in the electric field. Thus, it can no longer be guaranteed that the sensor response is linear to the incoming aerosol. The worst-case scenario of a short circuit also applies here.
Modifications 
3D printing 
Other possible modifications are the use of different 3D printing resins. There are many different resins on the market that can change the density, flexibility, temperature resistance, and strength of the sensor housing.
Sensor dimensions 
The first design criterion for the sensor is a safety configuration. The dielectric strength of air between the electrodes is 3 mm/kV. This length must not be undercut in any case. The higher the electric potential, the more particles are deposited, and these deposited particles are then prone to form dendrites. The dimensions of the electrodes were chosen so that easily available standard components can be used. Designs of similar sensors known to the authors used the following dimensions for a flat sensor: 9 mm width, 2 mm length, 1 mm gap, and 15 mm length, with a diameter of 8.5 mm and gap of 1.3 mm for a cylindrical design12,13. In addition, it should be ensured that the sensor can be manufactured by hand in a normal workshop. A 1 mm gap is the absolute minimum gap that still allows the sensor to be cleaned manually. Here, 1 kV was used as a good compromise of safety and efficient particle deposition, as well as availability of voltage sources in this range.
Electrodes 
Since the exact distance of 1 mm between the sensor electrodes is so crucial for performance, even more development work can be put into this step. For example, the 3D printed fixture can be made even more accurate, or a lathe can be used instead of a simple pipe cutter for cutting and deburring, if the equipment is available. Another option is to use a saw instead of a pipe cutter. In this case, the edges of the saw must be ground afterward. This method causes less deformation than the pipe cutter, but takes longer. In comparison to epoxy glue, silicone gives the cables more room to move, and it becomes easier to respace the electrodes. However, since the cables have more room to move, it is more difficult to seal the sensor. Instead of the vacuum clamp, which is easier to open at once, a self-made design is also feasible. Here, only holes for some screws and a cavity for the sealing cord must be altered in the 3D design.
MFC 
The MFC determines how much of the aerosol is sucked through the sensor; the rest should be able to be drained through an overflow with a HEPA filter placed at the end of the overflow, to avoid pollution of the room. By choosing a less expensive pump instead of an MFC, higher flow fluctuations will influence the sensor signal negatively.
Dilution bridge 
As seen in Figure 9, a dilution bridge can be built with a simple needle valve parallel to one or more HEPA filters. Other designs include a small vise to squeeze the tube instead of the needle valve. This design has the advantage that the tube can be cleaned more easily. The more coils such a vise has, the finer the concentration can be adjusted. This is especially important for calibration measurements, where high dynamics should be avoided.
Bench multimeter 
The bench multimeter measures a voltage, which must be divided by the value of internal resistance to obtain the correct current value. Depending on the chosen measuring range (e.g., 100 V), this internal resistance value can vary (e.g., 1 M&#8486;). It is important to select a defined range so that the internal resistance value is the same for all measured values. If &#34;auto range&#34; is chosen, the internal resistance value must be tracked as well.
Troubleshooting 
3D printer 
If the printer stops, the tank should be checked for residues of the last print; the mixer often gets stuck. One should observe the first minutes of the printing process. If it is clogged, it is either because the correct slicer settings have not been set or the fresh print has not been stored under UV protected conditions before post-processing. In the slicer settings, no support points should obstruct the flow channel and the space between the electrodes, and the internal support structures box must be unclicked before sending the file to the printer.
Aerosol source + dilution bridge 
If the aerosol source seems unstable, all the HEPA filters should be checked to ensure they are in the correct position and are not clogged. Also, the aerosol generator as well as the reference instrument should be checked to ensure they have finished their warm-up phase.
Sensor 
The most common faults are caused by an insufficient power supply connection, an air leak at the sensor, or when deposited particles form soot bridges between the electrodes. First, the sensor is opened to check if soot bridges have formed between the electrodes. The power source must be turned off before disconnecting the sensor cables and opening the sensor. Soot bridges are easily visible to the naked eye and can be removed with little effort. To remove soot bridges, it is best to use an optical cleaning cloth or lint-free cotton swab.
A leak that changes the flow behavior in the sensor, as well as a lower voltage at the electrodes, can change the sensor signal. It is not possible to say in advance which of these problems is responsible for an unexpected sensor response. Therefore, it is important to check both the tightness and the voltage stability as follows. First, connection from the cable to the electrodes is checked (protocol step 4.4). Next, the voltage source is checked to see if it is delivering the expected volts. An air leak is best identified with leak spray. In addition to this, the tightness can also be checked with a vacuum pump, as described in protocol step 4.4.2.
Limitations 
The limitation of an electrostatic sensor is well described by Maricq et al.14. In their work, they emphasize the importance of a stable voltage source and a stable sensor flow for the performance of the sensor. For this reason, a setup with an MFC or a pump should always be used for flow control, as described in Figure 10. In addition, the sensor needs a longer time to reach equilibrium during the first test. In further experiments, where a stable dendrite population has settled on the electrodes, the amount of time to start up the sensor is reduced. However, it should be generally noted that the sensor always needs a startup time to become operational depending on the initial concentration.
Unlike a flat design, as in Bilby et al., sensor drift is not a major problem in this cylindrical arrangement12. However, fast concentration changes at low particle concentrations are still difficult to detect with the sensor. As indicated by Diller et al. and Maricq et al., for a meaningful measurement signal, the measured value is averaged over 2-10 min, depending on how much the flow changes in the experiment14,15.
With a slope of 2.8 nAm3/mg and a standard deviation of &#177;1.4 nA, the deviation from the regression line in Figure 11 is high. For a better understanding of the sensor accuracy, the comparison of several experiments is recommended. For repeated experiments, the slope accounts for 3.5 nAm3/mg with a standard deviation of &#177;1.0 nA, and 4.9 nAm3/mg with a standard deviation of &#177; 0.6 nA. In addition, the sensor will give a very high reading the moment the voltage source is switched on. This start value is filtered out of the measurement data.
The advantage of the method presented here lies clearly in the simplicity, but also in the versatile possibilities to adapt the sensor shape to different needs. Therefore, in addition to soot, the sensor can detect a large variety of charged particles and is suitable for a wide range of applications, for example, particulate matter detection from power plants, wildfires, industries, and automobiles. This paper should be an incentive to agencies, companies, research teams, citizen scientists, and anyone interested in the detection of particulate matter to reproduce this simple sensor construction manual and build their own particle detector.

Inhalation of particles with a size of 1 &#181;m or smaller poses a high risk of adverse health effects on the human body. With increasing environmental pollution from combustion processes, respiratory diseases are growing in the population1,2,3. To promote health and counteract pollution, it is necessary to first identify the sources of pollution and quantify the degree of pollution. This can be done with existing particle detectors. However, these are large and very often far too expensive for private or citizen science purposes.
Many of the commercially available particle detectors are bulky, very expensive, and require additional equipment to be operated4. Most of them also need several aerosol-conditioning steps. For example, dilution is needed for detectors that use light scattering as their measurement principle, and the measurement range is limited by the wavelength5,6,7. Particle detectors that use laser-induced incandescence as a detection principle need both high energy laser sources and an energy-consuming cooling system8.
Particle detectors that use condensation particle counters are normally used as the gold standard for particle concentration measurement; these need preconditioning, dilution, and working fluids (e.g., butanol)9,10,11. The advantages of an electrostatic sensor lie in the simple and compact design and the low fabrication costs. However, in comparison to condensation particle counters, significant deductions have to be made regarding accuracy.
An electrostatic sensor represents an alternative to these methods. Electrostatic sensors can be robust, light, inexpensive to manufacture, and can be operated without supervision. The simplest form of an electrostatic sensor is a parallel plate capacitor with a high electric field between its plates. As aerosol is conveyed into the high voltage region between the two copper electrodes, naturally charged particles deposit on the electrodes of different polarity12 (Figure 1).
Dendrites form on the surface of the electrodes in the direction of the field lines of the applied high voltage between the electrodes, and are charged via contact charging. Fragments of these dendrites eventually break off the electrodes and redeposit on the electrode with opposite polarity, transferring their charge. These fragments carry a high number of charges. Because the electrode is grounded, the deposited charge generates a current leading to a voltage drop at the internal resistance of the bench multimeter. The more often this happens per unit of time, the higher the current, and consequently, the higher the voltage drop (Figure&#160;2).
Owing to the high voltage induced by the charge deposition of the fragments, no further amplifier electronics are needed. The formation of dendrite break-off particles and the subsequent charge release of these particles represents a natural signal amplification12. The resulting sensor signal is proportional to the particle mass concentration. This signal can be detected with an off-the-shelf bench multimeter.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/64844/64844fig01.jpg" /> 
Figure 1: Sensor schematics. Aerosol flows into the aerosol inlet, is propagated through the left flow channel, and then reaches the gap between the high-voltage electrode (inner electrode) and the measuring electrode (outer electrode). There, the particles contribute to dendrite growth and, as previously explained, break-off, thus generating the sensor response. Afterward, the particles flow further through the right flow channel and leave the sensor at the aerosol outlet. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/64844/64844fig02.jpg" /> 
Figure 2: Physical principle. Positively and negatively charged particles, as well as neutral particles, enter the gap between the electrodes of opposite polarity. They are diverted by the electric field lines to the electrode of opposite polarity and deposit their charge there. Then, they become part of a dendrite and take over the charge of the respective electrode. The field density is highest at the dendrite tip, where more particles are trapped. When the drag force exceeds the binding forces, segments of the dendrites break off, which in turn strike the opposite electrode and deposit their charges. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
With a cylindrical design, as in Warey et al.10, the probability of soot bridges forming can be minimized. Further information about the sensor geometry, applied voltage, gas flow velocity, and particulate matter concentration can be found there. They suggest correlation of the sensor signal to particulate matter streaming through the sensor (equation 1).
Sensor (V) = 5.7 &#215; 10-5 C V0 e0.62V &#215; <img alt="Equation 1" src="/files/ftp_upload/64844/64844eq01.jpg" style="margin: auto;" />&#160; &#160; &#160;(1)
C is the mass concentration of the particulate matter, V0 is the applied voltage, V is the exhaust velocity, L is the electrode length, and S is the electrode gap13.
Bilby et al. focused on the detailed study of the underlying physical effect of the electrostatic sensor9. These studies included an optically accessible setup and a kinetic model to explain the signal amplification of the dendrite-based sensor (see equations 2 and 3).
<img alt="Equation 2" src="/files/ftp_upload/64844/64844eq02v2.jpg" style="margin: auto;" />&#160; &#160; &#160;(2)
<img alt="Equation 3" src="/files/ftp_upload/64844/64844eq03v2.jpg" style="margin: auto;" />&#160; &#160; &#160;(3)
S represents a stack of soot discs of 10-100 soot agglomerates with a size of 50-100 nm; Dn represents a dendrite with n disks; Br denotes a break-off fragment composed of f disks; S and ki are rate constants12.
This paper presents a protocol on how to build and test a simple but efficient low-cost particle detector that can be used for high particle concentrations without further equipment. Previous work on this type of electrostatic sensor has mostly focused on exhaust measurements. In this work, laboratory-generated soot particles are used as test aerosols. The described sensor is based on `previous work from Warey et al. and Bilby et al12,13.
The sensor body consists of a stereolithography-based 3D printed body, coaxial electrodes cut from copper tubes, a vacuum gasket, and a vacuum clamp. Materials such as the vacuum gasket, cable, copper tubes, and 3D resin for one sensor cost less than &#8364;40. The additional equipment needed is a high-voltage source, a USB bench multimeter, and a soldering station. To evaluate the sensor, a defined aerosol source and a reference instrument are also required once (see Table of Materials). The size of the sensor described in this protocol is 10 cm x 7 cm. This size was chosen specifically for the experiment and can still be reduced significantly (see modifications/sensor dimensions in the discussion).
This protocol describes how to build, test, and use a simple low-cost particle sensor. A schematic of the protocol is shown in Figure&#160;3-beginning with the 3D print of the sensor hull and the electrode manufacturing, the assembly of the sensor, as well as testing and an example of field application of the sensor.
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/64844/64844fig03.jpg" /> 
Figure 3: Schematic for the method. The protocol is divided into four major steps. First, all parts for the sensor housing are printed. Then, the electrodes are manufactured. In the third step, the 3D printed sensor housing with the electrodes and the vacuum gasket are assembled. In the last step, the sensor performance is evaluated. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The most important steps of the 3D printing process are shown in Figure 4. At first, the right slicer settings for the print are chosen. Afterward, the most important parts of the print and the preprocessing of the 3D printed model are discussed. For this step, a resin 3D printer with an isopropanol bath and UV hardening device and a straight grinder are needed.
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/64844/64844fig04.jpg" /> 
Figure 4: Schematic of 3D print. (A) The slicer 3D model is depicted; (B) the printer during the printing process. Postprocessing steps: (C) flushing and (D) UV-hardening. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Figure 5 shows the most important steps of electrode manufacturing: the form shaping of the electrodes as well as the soldering of the contact to the electrodes. For this step, two copper tubes with different diameters, a caliper, a pipe cutter, a straight grinder, a vice, a soldering station and soldering tin, isolated cables with two different colors, thermal protective gloves, and a wire cutter are needed.
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/64844/64844fig05.jpg" /> 
Figure 5: Electrode manufacturing. (A) Measuring, (B) cutting, (C) deburring, and (D) soldering of the electrodes. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig05large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The assembly section in the protocol explains how the sensor is assembled. The most important sensor parts are depicted in Figure 6, namely the outer electrode holder, the flow channel, and the inner electrode holder. Figure 7 shows the most important steps in the sensor assembly. For this step, epoxy glue, protective clothing, a vacuum seal, a vacuum clamp, safety goggles, and gloves are needed.
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/64844/64844fig06.jpg" /> 
Figure 6: Sensor parts. (A)&#160;The outer electrode holder, (B) flow channel, and (C) the inner electrode holder. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig06large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 7" class="xfigimg" src="/files/ftp_upload/64844/64844fig07.jpg" /> 
Figure 7: Sensor assembly. All steps of the sensor assembly are shown. A-E shows the assembly of one half of the sensor. (A) The inner electrode holder is glued to the flow channel. (B) The inner electrode is placed onto the inner electrode holder. (C) The outer electrode is placed into the outer electrode holder. (D) The outer electrode holder is glued onto the flow channel + inner electrode holder assembly. (E) The vacuum sealing snaps into the outer electrode of one sensor half and then snaps into (C), the identical second outer electrode of the other sensor half. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig07large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The test section explains how to set up the experiment to compare the newly built sensor with a reference instrument. For this step, a bench multimeter, vacuum pump, high-voltage supply, aerosol generator, dilution bridge, aerosol tubes, Y-fitting, one mass flow controller (MFC), an aerosol mixer, a reference instrument, and a cotton swab are needed.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Equipment</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>3D printer</td>
			<td>Formlabs</td>
			<td></td>
			<td>Formlabs 3</td>
		</tr>
		<tr>
			<td>Aerosol Mixer</td>
			<td>ESSKA</td>
			<td>304200812095</td>
			<td>95 mm, diameter 8 mm</td>
		</tr>
		<tr>
			<td>Aerosol soot generator</td>
			<td>Jing Aerosol</td>
			<td></td>
			<td>Model 5201 Type C miniCAST</td>
		</tr>
		<tr>
			<td>Benchmultimeter</td>
			<td>Keysight</td>
			<td></td>
			<td>KEYSIGHT 34465A, 0 - 100 V range, 1 M&#937; internal resistance</td>
		</tr>
		<tr>
			<td>Dilution Bridge</td>
			<td>Custom built</td>
			<td></td>
			<td>Needel valve and HEPA filter in parallel</td>
		</tr>
		<tr>
			<td>High voltage power supply</td>
			<td>Stanford Research Systems</td>
			<td></td>
			<td>PS350, 5000 V - 25 W</td>
		</tr>
		<tr>
			<td>Mas flow controller</td>
			<td>V&#246;gtlin</td>
			<td>GSC-C3SA-BB26</td>
			<td>Red-y for gas flow, flow range: 0-10 L/min</td>
		</tr>
		<tr>
			<td>Refence Instument</td>
			<td>AVL</td>
			<td></td>
			<td>MSSplus - AVL Micro Soot Sensor</td>
		</tr>
		<tr>
			<td>Material</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Aerosol tygon tubes</td>
			<td>Saint Gobain Fluid Transfer</td>
			<td>AAG00012</td>
			<td>Diameter 7 mm</td>
		</tr>
		<tr>
			<td>Bidirectional flow control valves series RFO</td>
			<td>CAMOZZI</td>
			<td>RFO 383-1/8</td>
			<td>P max 10 bar</td>
		</tr>
		<tr>
			<td>Copper tube 12 mm</td>
			<td>Obi</td>
			<td>1996602</td>
			<td>Diameter 12 mm</td>
		</tr>
		<tr>
			<td>Copper tube 18 mm</td>
			<td>Obi</td>
			<td>1499441</td>
			<td>Diameter 18 mm</td>
		</tr>
		<tr>
			<td>Copper tube 22 mm</td>
			<td>Obi</td>
			<td>&#160;1996628</td>
			<td>Diameter 22 mm</td>
		</tr>
		<tr>
			<td>Cotton swab</td>
			<td>Chemtronics</td>
			<td>48042F</td>
			<td>50 m, 1 mm tip</td>
		</tr>
		<tr>
			<td>Epoxy glue</td>
			<td>RS components</td>
			<td>132605</td>
			<td>RS quick set epoxy</td>
		</tr>
		<tr>
			<td>Hepa Nylon Einweg-Inline-Filter</td>
			<td>Parker</td>
			<td>9933-05-BQ</td>
			<td>Fl&#252;ssigkeit 5.4SCFM 1/4Zoll, mit G1/4 Anschluss 8,1 bar</td>
		</tr>
		<tr>
			<td>Isolated electrical cable</td>
			<td>Nexans</td>
			<td></td>
			<td>Diameter 2 mm, two different colors red and black</td>
		</tr>
		<tr>
			<td>Photopolymer Resin</td>
			<td>Formlabs</td>
			<td>851976006196</td>
			<td>1 L&#160; Cartridge - Transparent (Clear)</td>
		</tr>
		<tr>
			<td>Soldering tin</td>
			<td>Stannol</td>
			<td>574108</td>
			<td></td>
		</tr>
		<tr>
			<td>Steckverbinder reduziert mit Stecknippel</td>
			<td>ESSKA</td>
			<td>IQSG120H6000</td>
			<td></td>
		</tr>
		<tr>
			<td>Tefen polymer Y - fitting</td>
			<td>TEFEN</td>
			<td>TEF-8357-06-00</td>
			<td></td>
		</tr>
		<tr>
			<td>Thermal protection gloves</td>
			<td>As One</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Vacuum clamp</td>
			<td>MISUMI</td>
			<td>FRNWC40</td>
			<td>Clamp</td>
		</tr>
		<tr>
			<td>Vacuum seal</td>
			<td>MISUMI</td>
			<td>FRNWR40</td>
			<td>Centering ring with O-ring seal</td>
		</tr>
		<tr>
			<td>Tool</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Caliper</td>
			<td>Starrett</td>
			<td>DW990</td>
			<td></td>
		</tr>
		<tr>
			<td>Deburrer</td>
			<td>Ruko</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Gloves</td>
			<td>BM Polyoo</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Isopropanol bath</td>
			<td>Formlabs</td>
			<td>FK-F3-01</td>
			<td>Form 3 finish kit</td>
		</tr>
		<tr>
			<td>PCB vice</td>
			<td>RS components</td>
			<td>221-7531</td>
			<td></td>
		</tr>
		<tr>
			<td>Pipe cutter</td>
			<td>Rigid</td>
			<td></td>
			<td>35S</td>
		</tr>
		<tr>
			<td>Safety goggles</td>
			<td>3M</td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Sand paper</td>
			<td>Mirka</td>
			<td></td>
			<td>Different sandpaper thicknesses 40 - 200</td>
		</tr>
		<tr>
			<td>Soldering station</td>
			<td>Ersa</td>
			<td></td>
			<td>Ersa i-CON 2, 400 &#176;C, 2.2 mm soldering rod</td>
		</tr>
		<tr>
			<td>Straight grainder</td>
			<td>Dremel</td>
			<td>F013400046</td>
			<td>Dremel 4000</td>
		</tr>
		<tr>
			<td>UV Hardening device</td>
			<td>Formlabs</td>
			<td>FH-CU-01</td>
			<td>Form cure</td>
		</tr>
		<tr>
			<td>Vacuum pump</td>
			<td>Mityvac</td>
			<td>MV8000</td>
			<td>Automotive Tune-up and Brake Bleeding Kit</td>
		</tr>
		<tr>
			<td>Vise</td>
			<td>Proxxon</td>
			<td>NO 28 132</td>
			<td>MS4,&#160; Jaw height 10 mm, Max. Clamping width 34 mm</td>
		</tr>
		<tr>
			<td>Wire cutter</td>
			<td>KNIPEX</td>
			<td>7712115</td>
			<td></td>
		</tr>
		<tr>
			<td>Software</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>MFC software</td>
			<td>V&#246;gtlin</td>
			<td></td>
			<td>Get red-y</td>
		</tr>
		<tr>
			<td>Reference Instument Software</td>
			<td>AVL</td>
			<td></td>
			<td>Supplied with the device: MSSplus</td>
		</tr>
		<tr>
			<td>Slicer software</td>
			<td>Formlabs</td>
			<td></td>
			<td>Preform Download Link: https://formlabs.com/de/software/</td>
		</tr>
	</tbody>
</table>

additive manufacturing-enabled low-cost particle detector

As particles with a size of 1 &#181;m or smaller pose a severe health risk to the human body, the detection and regulation of particle emissions are of great importance. A large share of particulate emissions are emitted by the transport sector. Most of the commercially available particle detectors are bulky, very expensive, and need additional equipment. This paper presents a protocol to build and test a standalone particle detector that is small and cost-efficient. 
The focus of this paper lies in the description of the detailed construction manual with video and the sensor evaluation procedure. The computer-aided design model of the sensor is included in the supplemental material. The manual explains all the construction steps, from 3D printing to the fully operational sensor. The sensor can detect charged particles and is therefore suitable for a wide range of applications. A possible field of application would be soot detection from power plants, wildfires, industries, and automobiles.

The exact correlation of the sensor signal to particulate mass varies based on particle charge distribution and size distribution, as well as the aerosol composition. Therefore, the sensor must be calibrated to a particular application with a reference instrument. This section explains how to compare the newly built sensor with a reference instrument.
The starting phase of the sensor takes approximately 5-10 min, depending on the chosen particle concentration. Within the starting phase, the sensor signal significantly increases while the sensor is exposed to a constant particle concentration. After the starting phase, the sensor signal stabilizes. At that stage, an equilibrium state for accumulation and fragmentation of dendrites is reached and the sensor signal is then proportional to the incoming soot concentration. After this initialization phase, the sensor is ready to measure any changes in aerosol concentration.
The measurement data shown in Figure 11 starts from the moment the sensor is in the above-mentioned equilibrium state. To calculate the sensor current in amperes, the collected data in volts must be divided by the value of internal resistance to obtain the correct current value.
The vertical axis shows the sensor signal in amperes and the horizontal axis shows the aerosol concentration measured by the reference instrument in mg/m3. A linear fit with its representative parameters is also given in the plot. The high uncertainty of the measured data is due to the high dynamics when adjusting the concentration with the dilution bridge. The linear fit parameters are an R2 value of 0.80, an intercept of -0.53 nA, and a slope of 2.80 nAm3/mg with a standard deviation of 1.4 nA.
<img alt="Figure 11" class="xfigimg" src="/files/ftp_upload/64844/64844fig11.jpg" /> 
Figure 11: Positive results. The sensor signal is plotted on the vertical axis in amperes, whereas the particle concentration measured by the reference instrument in mg/m3 is plotted on the horizontal axis. In addition, a linear fit with the most important parameters is added to the plot. The linear fit parameters are an R2 value of 0.80, an intercept of -0.53 nA, and a slope of 2.80 nAm3/mg. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig11large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
There is also the possibility that particles clog the path between the electrodes, in which case conductive soot bridges form between the electrodes. Because soot is a conductive material, these soot bridges form a short circuit between the electrodes. The measured signal rises rapidly with increasing thickness of the conductive path, up to the point where the voltage becomes so high that the voltmeter might be damaged. An example for an experiment with forming soot bridges can be seen in Figure 12. The signal rises in very steep jumps/steps and does not stop or flatten out. Dendrites are also no longer formed, and the sensor is no longer in a state of equilibrium. In this case, the high-voltage source must be switched off immediately, the sensor has to be cleaned, and a new measurement has to be started.
<img alt="Figure 12" class="xfigimg" src="/files/ftp_upload/64844/64844fig12.jpg" /> 
Figure 12: Negative result. A short circuit has occurred during the measurement. The sensor signal in amperes is plotted on the vertical axis and the measurement time is plotted on the horizontal axis. The sensor signal continues to increase without restriction. <a href="https://www.jove.com/files/ftp_upload/64844/64844fig12large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
If a flat line is displayed and the sensor current does not rise at all to a value above 1 nA, follow the troubleshooting directions in the discussion section. The sensor must be in the equilibrium state at all times to measure the entering aerosol accurately; therefore, a sufficiently high initial aerosol concentration has to be provided at the beginning of the experiment.
Supplemental File 1: This file represents the computer-aided design (CAD) file to print out the flow channel depicted in Figure 7A with holes for the cable. <a href="https://www.jove.com/files/ftp_upload/64844/flow_channel.zip" target="_blank">Please click here to download this File.</a>
Supplemental File 2: This file represents the CAD file to print out the flow channel depicted in Figure 7A without holes. <a href="https://www.jove.com/files/ftp_upload/64844/flow_channel_no_holes.zip" target="_blank">Please click here to download this File.</a>
Supplemental File 3: This file represents the CAD file to print out the inner electrode holder depicted in Figure 7A. <a href="https://www.jove.com/files/ftp_upload/64844/inner_electrode_holder.zip" target="_blank">Please click here to download this File.</a>
Supplemental File 4: This file represents the CAD file to print out the outer electrode holder depicted in Figure 7C (right). <a href="https://www.jove.com/files/ftp_upload/64844/outer_electrode_holder.zip" target="_blank">Please click here to download this File.</a>
Supplemental File 5: This file represents the CAD file to print out the flow channel without holes depicted in Figure 7C (left). <a href="https://www.jove.com/files/ftp_upload/64844/outer_electrode_holder_no_holes.zip" target="_blank">Please click here to download this File.</a>
Supplemental File 6: This file represents the CAD file to print out the electrode spacer. <a href="https://www.jove.com/files/ftp_upload/64844/electrode_glue_spacer.zip" target="_blank">Please click here to download this File.</a>

Watch this Scientific Journal Video about Additive Manufacturing-Enabled Low-Cost Particle Detector at JoVE.com

Additive Manufacturing-Enabled Low-Cost Particle Detector

Here, we present a protocol on how to build and test a simple but efficient low-cost particle detector.

As particles with a size of 1 &#181;m or smaller pose a severe health risk to the human body, the detection and regulation of particle emissions are of ...

additive-manufacturing-enabled-low-cost-particle-detector

Research

JoVE Journal

Engineering

1.1K Views.  Silicon Austria Labs. Here, we present a protocol on how to build and test a simple but efficient low-cost particle detector. 

Video: Additive Manufacturing-Enabled Low-Cost Particle Detector

Echo Particle Image Velocimetry

The transport of mass, momentum, and energy in fluid flows is ultimately determined by spatiotemporal distributions of the fluid velocity field.1 Consequently, a prerequisite for understanding, predicting, and controlling fluid flows is the capability to measure the velocity field with adequate spatial and temporal resolution.2 For velocity measurements in optically opaque fluids or through optically opaque geometries, echo particle image velocimetry (EPIV) is an attractive diagnostic technique to generate "instantaneous" two-dimensional fields of velocity.3,4,5,6 In this paper, the operating protocol for an EPIV system built by integrating a commercial medical ultrasound machine7 with a PC running commercial particle image velocimetry (PIV) software8 is described, and validation measurements in Hagen-Poiseuille (i.e., laminar pipe) flow are reported.
For the EPIV measurements, a phased array probe connected to the medical ultrasound machine is used to generate a two-dimensional ultrasound image by pulsing the piezoelectric probe elements at different times. Each probe element transmits an ultrasound pulse into the fluid, and tracer particles in the fluid (either naturally occurring or seeded) reflect ultrasound echoes back to the probe where they are recorded. The amplitude of the reflected ultrasound waves and their time delay relative to transmission are used to create what is known as B-mode (brightness mode) two-dimensional ultrasound images. Specifically, the time delay is used to determine the position of the scatterer in the fluid and the amplitude is used to assign intensity to the scatterer. The time required to obtain a single B-mode image, t, is determined by the time it take to pulse all the elements of the phased array probe. For acquiring multiple B-mode images, the frame rate of the system in frames per second (fps) = 1/&delta;t. (See 9 for a review of ultrasound imaging.)
For a typical EPIV experiment, the frame rate is between 20-60 fps, depending on flow conditions, and 100-1000 B-mode images of the spatial distribution of the tracer particles in the flow are acquired. Once acquired, the B-mode ultrasound images are transmitted via an ethernet connection to the PC running the PIV commercial software. Using the PIV software, tracer particle displacement fields, D(x,y)[pixels], (where x and y denote horizontal and vertical spatial position in the ultrasound image, respectively) are acquired by applying cross correlation algorithms to successive ultrasound B-mode images.10 The velocity fields, u(x,y)[m/s], are determined from the displacements fields, knowing the time step between image pairs, &Delta;T[s], and the image magnification, M[meter/pixel], i.e., u(x,y) = MD(x,y)/&Delta;T. The time step between images &Delta;T = 1/fps + D(x,y)/B, where B[pixels/s] is the time it takes for the ultrasound probe to sweep across the image width. In the present study, M = 77[&mu;m/pixel], fps = 49.5[1/s], and B = 25,047[pixels/s]. Once acquired, the velocity fields can be analyzed to compute flow quantities of interest.

An echo particle image velocimetry (EPIV) system capable of acquiring two-dimensional fields of velocity in optically opaque fluids or through optically opaque geometries is described, and validation measurements in pipe flow are reported.

The transport of mass, momentum, and energy in fluid flows is ultimately determined by spatiotemporal distributions of the fluid velocity field.1 ...

High-speed Particle Image Velocimetry Near Surfaces

Multi-dimensional and transient flows play a key role in many areas of science, engineering, and health sciences but are often not well understood. The complex nature of these flows may be studied using particle image velocimetry (PIV), a laser-based imaging technique for optically accessible flows. Though many forms of PIV exist that extend the technique beyond the original planar two-component velocity measurement capabilities, the basic PIV system consists of a light source (laser), a camera, tracer particles, and analysis algorithms. The imaging and recording parameters, the light source, and the algorithms are adjusted to optimize the recording for the flow of interest and obtain valid velocity data. 
Common PIV investigations measure two-component velocities in a plane at a few frames per second. However, recent developments in instrumentation have facilitated high-frame rate (&gt; 1 kHz) measurements capable of resolving transient flows with high temporal resolution. Therefore, high-frame rate measurements have enabled investigations on the evolution of the structure and dynamics of highly transient flows. These investigations play a critical role in understanding the fundamental physics of complex flows.
A detailed description for performing high-resolution, high-speed planar PIV to study a transient flow near the surface of a flat plate is presented here. Details for adjusting the parameter constraints such as image and recording properties, the laser sheet properties, and processing algorithms to adapt PIV for any flow of interest are included.

A procedure for studying transient flows near boundaries using high-resolution, high-speed particle image velocimetry (PIV) is described here. PIV is a non-intrusive measurement technique applicable to any optically accessible flow by optimizing several parameter constraints such as the image and recording properties, the laser sheet properties, and analysis algorithms.

Multi-dimensional and transient flows play a key role in many areas of science, engineering, and health sciences but are often not well understood. The ...

Micro-masonry for 3D Additive Micromanufacturing

Transfer printing is a method to transfer solid micro/nanoscale materials (herein called &#8216;inks&#8217;) from a substrate where they are generated to a different substrate by utilizing elastomeric stamps. Transfer printing enables the integration of heterogeneous materials to fabricate unexampled structures or functional systems that are found in recent advanced devices such as flexible and stretchable solar cells and LED arrays. While transfer printing exhibits unique features in material assembly capability, the use of adhesive layers or the surface modification such as deposition of self-assembled monolayer (SAM) on substrates for enhancing printing processes hinders its wide adaptation in microassembly of microelectromechanical system (MEMS) structures and devices. To overcome this shortcoming, we developed an advanced mode of transfer printing which deterministically assembles individual microscale objects solely through controlling surface contact area without any surface alteration. The absence of an adhesive layer or other modification and the subsequent material bonding processes ensure not only mechanical bonding, but also thermal and electrical connection between assembled materials, which further opens various applications in adaptation in building unusual MEMS devices.

This paper introduces a 3D additive micromanufacturing strategy (termed &#8216;micro-masonry&#8217;) for the flexible fabrication of microelectromechanical system (MEMS) structures and devices. This approach involves transfer printing-based assembly of micro/nanoscale materials in conjunction with rapid thermal annealing-enabled material bonding techniques.

Transfer printing is a method to transfer solid micro/nanoscale materials (herein called &#8216;inks&#8217;) from a substrate where they are generated to ...

Development of an Experimental Setup for the Measurement of the Coefficient of Restitution under Vacuum Conditions

The Discrete Element Method is used for the simulation of particulate systems to describe and analyze them, to predict and afterwards optimize their behavior for single stages of a process or even an entire process. For the simulation with occurring particle-particle and particle-wall contacts, the value of the coefficient of restitution is required. It can be determined experimentally. The coefficient of restitution depends on several parameters like the impact velocity. Especially for fine particles the impact velocity depends on the air pressure and under atmospheric pressure high impact velocities cannot be reached. For this, a new experimental setup for free-fall tests under vacuum conditions is developed. The coefficient of restitution is determined with the impact and rebound velocity which are detected by a high-speed camera. To not hinder the view, the vacuum chamber is made of glass. Also a new release mechanism to drop one single particle under vacuum conditions is constructed. Due to that, all properties of the particle can be characterized beforehand.

The coefficient of restitution is a parameter that describes the loss of kinetic energy during collision. Here, a free-fall setup under vacuum conditions is developed to be able to determine the coefficient of restitution parameter for particles in micrometer range with high impact velocities.

The Discrete Element Method is used for the simulation of particulate systems to describe and analyze them, to predict and afterwards optimize their ...

Flow-assisted Dielectrophoresis: A Low Cost Method for the Fabrication of High Performance Solution-processable Nanowire Devices

Flow-assisted dielectrophoresis (DEP) is an efficient self-assembly method for the controllable and reproducible positioning, alignment, and selection of nanowires. DEP is used for nanowire analysis, characterization, and for solution-based fabrication of semiconducting devices. The method works by applying an alternating electric field between metallic electrodes. The nanowire formulation is then dropped onto the electrodes which are on an inclined surface to create a flow of the formulation using gravity. The nanowires then align along the gradient of the electric field and in the direction of the liquid flow. The frequency of the field can be adjusted to select nanowires with superior conductivity and lower trap density. 
In this work, flow-assisted DEP is used to create nanowire field effect transistors. Flow-assisted DEP has several advantages: it allows selection of nanowire electrical properties; control of nanowire length; placement of nanowires in specific areas; control of orientation of nanowires; and control of nanowire density in the device. 
The technique can be expanded to many other applications such as gas sensors and microwave switches. The technique is efficient, quick, reproducible, and it uses a minimal amount of dilute solution making it ideal for the testing of novel nanomaterials. Wafer scale assembly of nanowire devices can also be achieved using this technique, allowing large numbers of samples for testing and large-area electronic applications.

In this paper, flow assisted dielectrophoresis is demonstrated for the self-assembly of nanowire devices. The fabrication of a silicon nanowire field effect transistor is shown as an example.

Flow-assisted dielectrophoresis (DEP) is an efficient self-assembly method for the controllable and reproducible positioning, alignment, and selection of ...

Multi-material Ceramic-Based Components &#8211; Additive Manufacturing of Black-and-white Zirconia Components by Thermoplastic 3D-Printing (CerAM - T3DP)

To combine the benefits of Additive Manufacturing (AM) with the benefits of Functionally Graded Materials (FGM) to ceramic-based 4D components (three dimensions for the geometry and one degree of freedom concerning the material properties at each position) the Thermoplastic 3D-Printing (CerAM -&#160;T3DP) was developed. It is a direct AM technology which allows the AM of multi-material components. To demonstrate the advantages of this technology black-and-white zirconia components were additively manufactured and co-sintered defect-free.
Two different pairs of black and white zirconia powders were used to prepare different thermoplastic suspensions. Appropriate dispensing parameters were investigated to manufacture single-material test components and adjusted for the additive manufacturing of multi-color zirconia components.

Here we describe a protocol for additively manufacturing black-and-white zirconia components by Thermoplastic 3D-Printing (CerAM -&#160;T3DP) and co-sintering defect-free.

To combine the benefits of Additive Manufacturing (AM) with the benefits of Functionally Graded Materials (FGM) to ceramic-based 4D components (three ...

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography

An additive manufacturing technology is applied to obtain functionally graded ceramic parts. This technology, based on digital light processing/stereolithography, is developed within the scope of the CerAMfacturing European research project. A three-dimensional (3-D) hemi-maxillary bone-like structure is 3-D printed using custom aluminum oxide polymeric mixtures. The powders and mixtures are fully analyzed in terms of rheological behavior in order to ensure proper material handling during the printing process. The possibility to print functionally graded materials using the Admaflex technology is explained in this document. Field-emission scanning electron microscopy (FESEM) show that the sintered aluminum oxide ceramic part has a porosity lower than 1% and no remainder of the original layered structure is found after analysis.

This manuscript describes the processing of single multifunctional ceramic components (e.g., combinations of dense-porous structures) additively manufactured by stereolithography.

An additive manufacturing technology is applied to obtain functionally graded ceramic parts. This technology, based on digital light ...

Quantifying the Relative Thickness of Conductive Ferromagnetic Materials Using Detector Coil-Based Pulsed Eddy Current Sensors

Thickness quantification of conductive ferromagnetic materials by means of non-destructive evaluation (NDE) is a crucial component of structural health monitoring of infrastructure, especially for assessing the condition of large diameter conductive ferromagnetic pipes found in the energy, water, oil, and gas sectors. Pulsed eddy current (PEC) sensing, especially detector coil-based PEC sensor architecture, has established itself over the years as an effective means for serving this purpose. Approaches for designing PEC sensors as well as processing signals have been presented in previous works. In recent years, the use of the decay rate of the detector coil-based time domain PEC signal for the purpose of thickness quantification has been studied. Such works have established that the decay rate-based method holds generality to the detector coil-based sensor architecture, with a degree of immunity to factors such as sensor shape and size, number of coil turns, and excitation current. Moreover, this method has shown its effectiveness in NDE of large pipes made of grey cast iron. Following such literature, the focus of this work is explicitly PEC sensor detector coil voltage decay rate-based conductive ferromagnetic material thickness quantification. However, the challenge faced by this method is the difficulty of calibration, especially when it comes to applications such as in situ pipe condition assessment since measuring electrical and magnetic properties of certain pipe materials or obtaining calibration samples is difficult in practice. Motivated by that challenge, in contrast to estimating actual thickness as done by some previous works, this work presents a protocol for using the decay rate-based method to quantify relative thickness (i.e., thickness of a particular location with respect to a maximum thickness), without the requirement for calibration.

Here, we present a protocol to quantify the relative thickness (i.e., thickness as a percentage with respect to a reference) of conductive ferromagnetic materials using detector coil-based pulsed eddy current sensors, while overcoming the calibration requirement.

Thickness quantification of conductive ferromagnetic materials by means of non-destructive evaluation (NDE) is a crucial component of structural health ...

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

A protocol is presented to build a custom low-cost yet high-performance femtosecond (fs) fiber laser. This all-normal-dispersion (ANDi) ytterbium-doped fiber laser is built completely using commercially available parts, including $8,000 in fiber optic and pump laser components, plus $4,800 in standard optical components and extra-cavity accessories. Researchers new to fiber optic device fabrication may also consider investing in basic fiber splicing and laser pulse characterization equipment (~$63,000). Important for optimal laser operation, methods to verify true versus apparent (partial or noise-like) mode-locked performance are presented. This system achieves 70 fs pulse duration with a center wavelength of approximately 1,070 nm and a pulse repetition rate of 31 MHz. This fiber laser exhibits the peak performance that may be obtained for an easily assembled fiber laser system, which makes this design ideal for research laboratories aiming to develop compact and portable fs laser technologies that enable new implementations of clinical multiphoton microscopy and fs surgery.

A method is presented to build a custom low-cost, mode-locked femtosecond fiber laser for potential applications in multiphoton microscopy, endoscopy, and photomedicine. This laser is built using commercially available parts and basic splicing techniques.

A protocol is presented to build a custom low-cost yet high-performance femtosecond (fs) fiber laser. This all-normal-dispersion (ANDi) ytterbium-doped ...

Manufacturing, Control, and Performance Evaluation of a Gecko-Inspired Soft Robot

This protocol presents a method for manufacturing, control, and evaluation of the performance of a soft robot that can climb inclined flat surfaces with slopes of up to 84&#176;. The manufacturing method is valid for the fast pneunet bending actuators in general and might, therefore, be interesting for newcomers to the field of actuator manufacturing. The control of the robot is achieved by means of a pneumatic control box that can provide arbitrary pressures and can be built by only using purchased components, a laser cutter, and a soldering iron. For the walking performance of the robot, the pressure-angle calibration plays a crucial role. Therefore, a semi-automated method for the pressure-angle calibration is presented. At high inclines (&#62; 70&#176;), the robot can no longer reliably fix itself to the walking plane. Therefore, the gait pattern is modified to ensure that the feet can be fixed on the walking plane.

This protocol provides a detailed list of steps to be performed for the manufacturing, control and evaluation of the climbing performance of a gecko-inspired soft robot.

This protocol presents a method for manufacturing, control, and evaluation of the performance of a soft robot that can climb inclined flat surfaces with ...