This work was supported as part of the Center for Understanding and Control of Acid-Gas Induced Evolution of Materials for Energy (UNCAGE-ME), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award #DE-SC0012577. J.S. acknowledges that this material is based upon work supported by the National Science Foundation Graduate Research Fellowship under Grant No. DGE-2039655. Any opinion, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.

1. Sample preparation
<ol>
	<li>Sample synthesis
	<ol>
		<li>Dissolve 0.35 mM terephthalic acid and 0.35 mM ZrCl4 in 4 mL of dimethyl formamide (DMF). Seal in a PTFE liner and heat at 120 &#176;C for 24 h. Allow to cool to room temperature.</li>
		<li>Centrifuge solution at 120 x g for 30 min. Decant remaining liquid and allow powder to dry in ambient air overnight.</li>
	</ol>
	</li>
	<li>Sample loading
	<ol>
		<li>Measure the mass of an empty sample tube. Load 30-50 mg of the MOF UiO-66 into the sample tube. Measure the new mass.</li>
	</ol>
	</li>
	<li>Activation
	<ol>
		<li>Attach the sample tube to the sample preparation system, securing the seal with a 0.5 inch O-ring. Place the tube inside the heating mantle.</li>
		<li>Set the temperature controller to the designated activation temperature, 120 &#176;C here, and wait for the temperature to stabilize. 
		NOTE: The activation temperature should be above the synthesis solvent&#39;s (or the solvent used in solvent exchange) boiling point under vacuum.</li>
		<li>Open the valve connecting the system to the vacuum and wait for the pressure to stabilize. Wait for the designated activation time, 24 h.</li>
		<li>Remove the tube from the heating mantle and allow the sample to cool to room temperature. Backfill the sample tube with nitrogen. Remove the tube from the preparation system.</li>
		<li>Take the mass of the activated sample and tube. Calculate the mass of the activated sample as described in equation 4 (eq. 4). 
		(sample mass) = (mass of activated sample and tube) - (mass of empty sample tube) (eq. 4)</li>
	</ol>
	</li>
</ol>
2. Experiment file setup
<ol>
	<li>Create a sample file
	<ol>
		<li>Open instrument software, click File, then click New Sample. Under the Sample Description tab, enter the sample name, sample mass, and sample density.</li>
	</ol>
	</li>
	<li>Input analysis parameters
	<ol>
		<li>Open the Analysis Conditions tab and select the adsorptive gas (nitrogen) and analysis conditions (BET).</li>
		<li>Select the Free Space button. Enter whether the free space is to be measured by the instrument, entered by the user, or calculated. If the free space will be measured, enter the duration of evacuation prior to the measurement.</li>
		<li>Select whether the nitrogen dewar will be lowered during the measurement and whether the system will perform a test for sample outgassing. If the free space will be entered, specify both the ambient free space and the analysis free space. Click OK. 
		NOTE: At 77 K, helium can become trapped inside micropores. For microporous materials, the helium free space may be measured after N2 adsorption analysis.</li>
		<li>Select p0 and T. Enter whether p0 will be measured by the po tube, entered by the user, or calculated. Typically, the P0 of the adsorbate is measured by the instrument. Input the analysis temperature (77K), and the p0 value if applicable. Click OK.</li>
		<li>Select Backfill. Select whether the sample will be backfilled before and after analysis. If either is chosen, select the identity of the backfill gas (N2). Click OK.</li>
		<li>In the Isotherm Collection section, select Target Pressures. Click Pressures, then input the isotherm pressure values from a p/p0 between 0 and 1 in intervals of 0.005, then click OK. Click Options and input the relative pressure tolerance of 5%. Click OK.</li>
		<li>Open the Report Options tab and select the data analysis plots to be reported. Click Save As, name the file, and select a folder destination.</li>
	</ol>
	</li>
</ol>
3. Performing adsorption measurement
<ol>
	<li>Physical setup
	<ol>
		<li>Slide the sample tubes into the isothermal sleeves. Attach the sample tube to adsorption instrument, securing the seal with O-rings.</li>
		<li>Fill dewar with liquid nitrogen using appropriate safety/personal protection equipment. Place the dewar on the elevator below the sample. If using p0 tube, attach it and ensure it is configured to sit inside the dewar once the elevator is raised.</li>
		<li>Close the shield doors.</li>
	</ol>
	</li>
	<li>Running the experiment
	<ol>
		<li>In the instrument software, click the name of the instrument then click Sample Analysis.</li>
		<li>Click Browse, then select the sample file. Ensure to match the analysis number with the number of the port where the sample is loaded. Click Start.</li>
	</ol>
	</li>
</ol>
4. Nitrogen adsorption measurement
<ol>
	<li>Adsorption: Inject nitrogen into the sample tube until the first target pressure (&#177; the pressure tolerance range) is reached. Leave the sample to equilibrate until the pressure is stable for the designated equilibration time. Repeat this until nitrogen&#39;s saturation pressure is reached.</li>
	<li>Desorption: Open the vacuum valve to desorb nitrogen until the first desorption target pressure (&#177; the pressure tolerance range) is reached. Leave the sample to equilibrate until the pressure is stable for the designated equilibration time. Repeat this until the nitrogen in the sample has been fully desorbed.</li>
	<li>Backfill the sample tube with designated backfill gas (N2). The instrument will automatically backfill the tubes if that option was selected when inputting the analysis parameters. 
	&#8203;NOTE: A diagram of the adsorption apparatus is shown in Figure 1.</li>
</ol>
5. Data analysis
<ol>
	<li>Once all data points have been collected, select File, then Export, and choose the experiment file. Enter the file destination and save the file as a spreadsheet. Click OK.</li>
	<li>Use the isotherm data to create a BET plot, with p/p0 on the x-axis and (p/p0)/[n(1-p/p0)] on the y-axis according to equation 1.
	<ol>
		<li>To apply the BET method to a given isotherm, take the linear range of the knee. For mesoporous materials this is typically in a P/P0 range of 0.05-0.30, while for microporous materials it is taken from a P/P0 range of 0.005-0.03.</li>
		<li>Make sure the linear range meets the Rouquerol criteria discussed below. There are tools available to automatically detect the linear range for MOF materials13. The linear range is: 
		Slope = (C-1)/(nmC) 
		&#8203;Y-intercept = 1/nmC</li>
		<li>Use the values of the BET plot&#39;s slope and the y-intercept to calculate the BET constant (C) and the monolayer capacity (nm)</li>
		<li>Use the monolayer capacity and adsorbate properties to calculate the total surface area using the relation presented in equation 3.</li>
	</ol>
	</li>
</ol>

Using Nitrogen Porosimetry to Characterize Metal-Organic Frameworks

<ol>
	<li>Zhou, H. C., Long, J. R., Yaghi, O. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Introduction+to+Metal-Organic+Frameworks.">Introduction to Metal-Organic Frameworks.</a> Chemical Reviews. 112 (2), 673-674 (2012).</li><li>Tian, Y., Wu, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+comprehensive+analysis+of+the+BET+area+for+nanoporous+materials.">A comprehensive analysis of the BET area for nanoporous materials.</a> AIChE Journal. 64 (1), 286-293 (2017).</li><li>Farha, O. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metal-organic+framework+materials+with+ultrahigh+surface+areas:+is+the+sky+the+limit.">Metal-organic framework materials with ultrahigh surface areas: is the sky the limit.</a> Journal of the American Chemical Society. 134 (36), 15016-15021 (2012).</li><li>Li, J. R., Sculley, J., Zhou, H. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metal-organic+frameworks+for+separations.">Metal-organic frameworks for separations.</a> Chemical Reviews. 112 (2), 869-932 (2012).</li><li>Yang, D., Gates, B. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Catalysis+by+Metal+Organic+Frameworks:+Perspective+and+Suggestions+for+Future+Research.">Catalysis by Metal Organic Frameworks: Perspective and Suggestions for Future Research.</a> ACS Catalysis. 9 (3), 1779-1798 (2019).</li><li>Kreno, L. E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metal-organic+framework+materials+as+chemical+sensors.">Metal-organic framework materials as chemical sensors.</a> Chemical Reviews. 112 (2), 1105-1125 (2012).</li><li>Wang, T. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrahigh+surface+area+zirconium+MOFs+and+insights+into+the+applicability+of+the+BET+theory.">Ultrahigh surface area zirconium MOFs and insights into the applicability of the BET theory.</a> Journal of the American Chemical Society. 137 (10), 3585-3591 (2015).</li><li>Ongari, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Accurate+Characterization+of+the+Pore+Volume+in+Microporous+Crystalline+Materials.">Accurate Characterization of the Pore Volume in Microporous Crystalline Materials.</a> Langmuir. 33 (51), 14529-14538 (2017).</li><li>Thommes, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Physisorption+of+gases,+with+special+reference+to+the+evaluation+of+surface+area+and+pore+size+distribution+(IUPAC+Technical+Report).">Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report).</a> Pure and Applied Chemistry. 87 (9-10), 1051-1069 (2015).</li><li>Brunauer, S., Emmett, P. H., Teller, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adsorption+of+Gases+in+Multimolecular+Layers.">Adsorption of Gases in Multimolecular Layers.</a> Journal of the American Chemical Society. 60 (2), 309-319 (1938).</li><li>Barrett, E. P., Joyner, L. G., Halenda, P. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Determination+of+Pore+Volume+and+Area+Distributions+in+Porous+Substances.+I.+Computations+from+Nitrogen+Isotherms.">The Determination of Pore Volume and Area Distributions in Porous Substances. I. Computations from Nitrogen Isotherms.</a> Journal of the American Chemical Society. 73 (1), 373-380 (1951).</li><li>Lowell, S., Shields, J. E., Thomas, M. A., Thommes, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Characterization of Porous Solids and Powders: Surface Area, Pore Size and Density. , (2004).</li><li>Osterrieth, J. W. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=How+Reproducible+are+Surface+Areas+Calculated+from+the+BET+Equation.">How Reproducible are Surface Areas Calculated from the BET Equation.</a> Advanced Materials. 34 (27), 2201502 (2022).</li><li>Cavka, J. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+New+Zirconium+Inorganic+Building+Brick+Forming+Metal+Organic+Frameworks+with+Exceptional+Stability.">A New Zirconium Inorganic Building Brick Forming Metal Organic Frameworks with Exceptional Stability.</a> Journal of the American Chemical Society. 130 (42), 13850-13851 (2008).</li><li>Winarta, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Decade+of+UiO-66+Research:+A+Historic+Review+of+Dynamic+Structure,+Synthesis+Mechanisms,+and+Characterization+Techniques+of+an+Archetypal+Metal-Organic+Framework.">A Decade of UiO-66 Research: A Historic Review of Dynamic Structure, Synthesis Mechanisms, and Characterization Techniques of an Archetypal Metal-Organic Framework.</a> Crystal Growth &amp; Design. 20 (2), 1347-1362 (2020).</li><li>Valenzano, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Disclosing+the+Complex+Structure+of+UiO-66+Metal+Organic+Framework:+A+Synergic+Combination+of+Experiment+and+Theory.">Disclosing the Complex Structure of UiO-66 Metal Organic Framework: A Synergic Combination of Experiment and Theory.</a> Chemistry of Materials. 23 (7), 1700-1718 (2011).</li><li>Rouquerol, F., Rouquerol, J., Sing, K. S. W., Maurin, G., Llewellyn, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Adsorption by Powders and Porous Solids (Second Edition). , (2014).</li><li>Agrawal, M., Han, R., Herath, D., Sholl, D. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Does+repeat+synthesis+in+materials+chemistry+obey+a+power+law).">Does repeat synthesis in materials chemistry obey a power law).</a> Proceedings of the National Academy of Sciences of the United States of America. 117 (2), 877-882 (2020).</li><li>Rouquerol, J., Llewellyn, P., Rouquerol, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Studies in Surface Science and Catalysis. , 160 (2007).</li><li>Howarth, A. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Best+Practices+for+the+Synthesis,+Activation,+and+Characterization+of+Metal-Organic+Frameworks.">Best Practices for the Synthesis, Activation, and Characterization of Metal-Organic Frameworks.</a> Chemistry of Materials. 29 (1), 26-39 (2017).</li><li>Kim, K. C., Yoon, T. U., Bae, Y. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Applicability+of+using+CO2+adsorption+isotherms+to+determine+BET+surface+areas+of+microporous+materials.">Applicability of using CO2 adsorption isotherms to determine BET surface areas of microporous materials.</a> Microporous and Mesoporous Materials. 224, 294-301 (2016).</li><li>Bau, S., Witschger, O., Gensdarmes, F., Rastoix, O., Thomas, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+TEM-based+method+as+an+alternative+to+the+BET+method+for+measuring+off-line+the+specific+surface+area+of+nanoaerosols.">A TEM-based method as an alternative to the BET method for measuring off-line the specific surface area of nanoaerosols.</a> Powder Technology. 200 (3), 190-201 (2010).</li></ol>

The authors have no competing financial interests.

Applicability and limitations 
The BET method requires a few key assumptions: (1) the surface is planar and uniform, (2) the surface is homogenous, and all adsorption sites are energetically identical (3) adsorbates form a monolayer. Because of this, BET may not be suitable for non-porous materials, materials with complex surface structures (different types of surface sites, irregular surface morphology, sites with large energetic differences), or those that do not exhibit monolayer adsorption behavior. Large deviations from assumption conditions may affect the accuracy of specific surface area calculations. Like BET, the BJH method also assumes uniform adsorption and a homogenous surface, along with the assumption of rigid, cylindrical pores. As such, it also may not be suitable for materials with complex surfaces, or breathable structures20. Additionally, since porosimetry requires access to pore space, calculated values will not account for closed pore volume.
Both the BET and BJH methods should be used cautiously with microporous materials. BJH does not account for fluid-surface interactions or interactions between adsorbate molecules within the pore, both of which become more pronounced in smaller pores. For this reason, BJH is limited to mesopores and small macropores. Since micropores often exhibit pore filling behavior, it can be difficult to locate the linear region of the isotherm that is required to perform BET calculations21.
An additional limitation to both methods is their sensitivity to sample preparation methods. The sample is required to be in a divided form, such as a powder or thin film, which can be challenging to prepare uniformly. This can introduce errors in measurements and make repeatability difficult. The surface area and pore volumes may also be affected by the sample preparation method and conditions, such as material synthesis technique, activation methods/conditions, or drying temperature/time22.
Significance with respect to alternative methods 
Nitrogen is the standard adsorbate for BET and BJH data, due to its quadrupole moment - where the orientation of the nitrogen molecule is dependent on the surface chemistry of the adsorbent, allowing for the formation of a monolayer - and its low cost17. However, argon and carbon dioxide23 can also be utilized, particularly for microporous structures.&#160;Argon is chemically inert and is a symmetrical, monoatomic molecule; however, 77 K is below its triple point so the bulk reference state is questionable, and the structure of the argon monolayer is heavily dependent on the surface chemistry of the sorbent17.
As both BET and BJH are not universally applicable, other methods of measuring surface area and pore volume should be considered. A Langmuir plot, t-plot, or the Horvath-Kawazoe method can be used to determine micropore surface area, pore volume, and pore size distribution, respectively. Non-local density functional theory (NLDFT) modeling is also an option for pore size distributions and is especially favorable for micropores because it accounts for changes in fluid density with respect to pore size. Mercury porosimetry can be used to determine both porosity and pore volume, but the accessible range for this technique must be considered since it cannot penetrate into micropores. Computational methods can be used to calculate theoretical characterization metrics and provide a point of comparison to experimental results, which can be useful for materials with closed pores. Although BJH produces a pore size distribution, it does not account for non-uniform distribution or fully characterize connectivity between pores. Additional characterization, such as SEM, TEM24, or XRD may be used to gain a more complete understanding of the structure of a porous material. Even when a material cannot be fully represented by BET or BJH, they can still be used as qualitative comparisons between materials. Nitrogen porosimetry can be a very useful tool in combination with other techniques.12

Relevance of surface area and pore volume 
The accurate characterization of porous materials is imperative to understanding their potential applications. Surface area and pore volume are important quantitative metrics that provide insight into metal-organic framework (MOF) performance in a variety of applications, including gas adsorption, separation, catalysis, and sensing1.
The surface area of a MOF is a parameter that quantifies the amount of surface available for interactions with guest molecules and can affect its performance in various applications2,3. In gas adsorption applications, the surface area of a MOF reflects binding site availability and affinity, which is directly related to its separation performance4. In catalysis applications, MOF surface area can affect the number of active sites and their accessibility to reactant molecules and, thus, their catalytic activity5. The quantity and accessibility of active sites are also relevant in sensing applications, as more guest interactions with active sites lead to improved sensitivity (and potentially selectivity)6. The surface area can also affect the stability of the MOF under extreme conditions, as a larger surface area can indicate a higher number of surface defects7.
The pore volume of a MOF is a parameter that quantifies the amount of void space within the porous structure. It is defined as the total volume of the pores in the MOF, which includes both the open (accessible) and closed (inaccessible) pores. The pore volume of a MOF can affect its performance in various applications, including gas adsorption, separation, and catalysis. Like surface area, the pore volume of a MOF is directly related to its capacity for gas uptake and storage and its ability to allow guest molecules to reach adsorptive or catalytic sites8.
Using nitrogen sorption to determine surface area and pore volume 
Both surface area and pore volume are typically measured using gas adsorption techniques, most commonly nitrogen sorption. Nitrogen is chosen as the adsorbate in Brunauer-Emmett-Teller (BET) analysis due to its quadrupole moment, where the orientation of the nitrogen molecule is dependent on the surface chemistry of the adsorbent, allowing for the formation of a monolayer. The plot of nitrogen uptake as a function of pressure can be used to obtain information about the surface and pore sizes of the MOF. The material surface area and total pore volume can be calculated using the sorption data9. The overall goal of the method detailed here is to obtain nitrogen sorption data and use that data to calculate MOF surface area and pore volume.
The BET method10 is a widely used technique for determining the specific surface area of a porous material, based on the principle that the adsorption of a gas onto a solid surface is a function of the surface area, the properties of the gas molecule, and the system. A known amount of an adsorbate gas (such as nitrogen) is introduced to the sample material over a given pressure range, and the amount of gas adsorbed onto the surface is measured at each pressure increment. The data is used to calculate the specific surface area by relating the adsorbate uptake, pressure, and monolayer capacity, which is represented by the BET equation9:
<img alt="Equation 1" src="/files/ftp_upload/65716/65716eq01.jpg" style="margin: auto;" /> (equation 1; eq. 1)
where: 
p = equilibrium pressure of adsorbate (Pa) 
p0 = adsorbate saturation pressure (Pa) 
n = adsorbate uptake amount (m3/g) 
nm = monolayer capacity (m3/g) 
C = BET constant (unitless)
The monolayer capacity is related to the total surface area by the following equation:
<img alt="Equation 2" src="/files/ftp_upload/65716/65716eq02.jpg" style="margin: auto;" /> (equation 2; eq. 2)
where: 
St = total MOF surface area (m2) 
nm = monolayer capacity (m3/g) 
NAv = Avogadro&#39;s number (molecule/mol) 
scs = cross sectional area of adsorbate molecule (m2/molecule) 
Vmolar = adsorbate molar volume (m3/mol)
The Barrett-Joyner-Halenda (BJH) method11 is a common procedure that utilizes desorption data to calculate the total pore volume. Like the BET method, a known amount of adsorbate gas (often nitrogen) is introduced to the sample. The partial pressure of the adsorbate is then incrementally decreased, and the volume of gas desorbed at each step is measured. Under the assumption that desorption in each pore first occurs in the capillary volume, followed by a reduction in adsorbed layer thickness, the BJH equation relates the volume desorbed to the adsorbed layer thickness, pore radius, and pore volume. This relationship can be represented with a BJH pore size distribution plot, which plots pore radius against pore volume. The distribution is integrated with respect to pore size to determine the total pore volume. The BJH equation12 is written as:
<img alt="Equation 3" src="/files/ftp_upload/65716/65716eq03.jpg" style="margin: auto;" /> (equation 3; eq. 3)
where: 
n = desorption step (unitless) 
vn = volume of pores emptied of capillary condensate (m3) 
&#916;Vn = volume of adsorbate removed from pores (m3) 
&#916;tn = change in adsorbed layer thickness (m) 
A = surface area of pores involved in desorption (m2) 
Rn = BJH constant dependent on average pore size (unitless) 
c = BJH constant, dependent on average adsorbed layer thickness (unitless)

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Adsorption Instrument</td>
			<td>Micromeritics</td>
			<td></td>
			<td>TriStar II Plus</td>
		</tr>
		<tr>
			<td>Adsorption Software</td>
			<td>Micromeritics</td>
			<td></td>
			<td>TriStar II Plus Version 3.03</td>
		</tr>
		<tr>
			<td>Balance</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Dewar</td>
			<td></td>
			<td></td>
			<td>Liquid N2 Dewar</td>
		</tr>
		<tr>
			<td>Dimethyl Formamide (DMF)</td>
			<td>Fisher Scientific</td>
			<td>D119-1</td>
			<td></td>
		</tr>
		<tr>
			<td>Helium</td>
			<td>Airgas</td>
			<td>HE UHP300</td>
			<td>Ultra-High Purity</td>
		</tr>
		<tr>
			<td>Nitrogen</td>
			<td>Airgas</td>
			<td>NI 230LT22</td>
			<td>Industrial Grade Liquid N2</td>
		</tr>
		<tr>
			<td>Nitrogen</td>
			<td>Airgas</td>
			<td>NI UHP300</td>
			<td>Ultra-High Purity Gaseous N2</td>
		</tr>
		<tr>
			<td>Sample Holder</td>
			<td>Micromeritics</td>
			<td>302-61001-02</td>
			<td>Glass Sample Holder</td>
		</tr>
		<tr>
			<td>Sample Preparation System</td>
			<td>Micromeritics</td>
			<td>061-00030-00</td>
			<td>VacPrep 061</td>
		</tr>
		<tr>
			<td>Terephthalic Acid (H2BDC)</td>
			<td>Sigma Aldrich</td>
			<td>185361</td>
			<td></td>
		</tr>
		<tr>
			<td>ZrCl4</td>
			<td>&#160;Sigma Aldrich</td>
			<td>221880</td>
			<td>Zirconium(IV) chloride, &#8805;99.5% trace metals basis</td>
		</tr>
	</tbody>
</table>

determining surface areas and pore volumes of metal-organic frameworks

The surface area and pore volume of a metal-organic framework (MOF) can provide insight into its structure and potential applications. Both parameters are commonly determined using the data from nitrogen sorption experiments; commercial instruments to perform these measurements are also widely available. These instruments will calculate structural parameters, but it is essential to understand how to select input data and when calculation methods apply to the sample MOF. This article outlines the use of the Brunauer-Emmett-Teller (BET) method and Barrett-Joyner-Halenda (BJH) method for the calculation of surface area and pore volume, respectively. Example calculations are performed on the representative MOF UiO-66. Although widely applicable to MOFs, sample materials and adsorption data must meet certain criteria for the calculated results to be considered accurate, in addition to proper sample preparation. The assumptions and limitations of these methods are also discussed, along with alternative and complementary techniques for the MOF pore space characterization.

After following the protocol, the obtained isotherm can be analyzed, and critical material properties can be derived. The results from a nitrogen adsorption experiment gives critical information into the surface area, pore volume, and pore structure of a given sorbent. The aim of this experiment was to investigate the use of nitrogen adsorption to measure the surface area and pore volume of a nanoporous MOF, UiO-66. UiO-66 is an archetypal zirconium-based MOF that has a high surface area and remarkable stability. While many MOFs possess weak thermal, mechanical, and chemical stability, UiO-66 is very robust due to the zirconium oxide cuboctahedral metal node, allowing for 12 extension points in the BDC linker coordination. The structure is comprised of 7.5 &#197; tetrahedron cages and 12 &#197; octahedral cages14,15.
Defect-free UiO-66 exhibits a type 1 isotherm shape16. Type 1 isotherms are indicative of microporous solids that have relatively small external surfaces. The amount adsorbed in a type 1 isotherm quickly approaches a limiting value, indicating that the nitrogen uptake is governed by the micropore volume that is accessible to the adsorbate, rather than the internal surface area. The sharp uptake at a low P/P0 indicates a strong interaction in the narrow micropores between the adsorbent and adsorbate17. Hysteresis loops are not commonly seen in type 1 isotherms as they are seen in the multilayer range of physisorption and are associated with capillary condensation in the pores. The monolayer formation of nitrogen on the adsorbent in the low P/P0 range is related to the surface area of the adsorbent, while pore filling at a P/P0 close to unity relates to the total pore volume of the material17.
The application of the BET method is often done in the adsorption instrument software. However, the analysis and calculation can easily be done manually, or with other computational programs and methods that can be adapted to give critical results. To apply the BET model to the obtained nitrogen isotherm, there are two critical steps. First, the nitrogen isotherm must be transformed into a BET plot, and from there the BET monolayer capacity can be derived. Next, the BET surface area is calculated from the monolayer capacity and by selecting an appropriate value of the molecular cross-sectional area17. This is typically done in nitrogen adsorption instrument software. Figure 2 shows the nitrogen isotherm obtained for UiO-66. The isotherm is type 1, indicating a microporous structure and a nitrogen monolayer formation. The sharp step at high relative pressures, resulting in a slight type 2 isotherm, is indicative of multilayer formation as well as the formation of larger meso- or macro-pores due to defect engineering in UiO-66. The hysteresis observed at high relative pressures indicates larger meso- and macro-pore formation. Table 1 shows the values obtained from the BET analysis.
When using the BET method, the Rouquerol criteria must hold true. The Rouquerol criteria state that a linear fit to the transformed BET data must be obtained, the C value should always be positive if the method is within the proper range for analysis, the Rouquerol transform must increase with increasing relative pressure, and the monolayer capacity must be within the limits of data used to fir the BET parameters18. To apply the BET method to a given isotherm, the linear range of the knee must be taken. For mesoporous materials this is typically in a P/P0 range of 0.05-0.30, while for many microporous materials it is typically taken from a P/P0 range of 0.005-0.03. However, the actual linear range is often more restricted as it is dependent on the material and the analysis temperature. Thus, the selection of the linear range will require qualitative assessment, similar to the parameters displayed in Table 1 (positive C and correlation coefficient close to unity indicating a proper analysis range). Similarly, there must be a sufficient number of experimental data points in the linear range (minimum of 10) for reliable analysis. These considerations also indicate inherent limitations with the BET method. C is a constant that relates to the relative pressure at which a monolayer is formed. C is a metric used to define the fraction of the surface uncovered by a monolayer as the BET method assumes a statistical monolayer formation. Thus, a larger C value correlates to a higher degree of surface coverage and a more uniform monolayer formation. When the C value is less than 2, the isotherm is type 3 or 5 and BET is not applicable. When C is less than 50 there is appreciable overlap of the monolayer and multilayer formation. A coefficient C of at least 80 indicates a sharp isotherm knee where monolayer adsorption is completed, and multilayer adsorption begins. A parameter C greater than 150 is typically associated with the filling of narrow micropores or adsorption on high energy surface sites17.
UiO-66 is a microporous MOF that commonly exhibits defects which can increase the surface area and improve certain desirable adsorption properties, but can result in a lower stability and crystallinity15. A defective UiO-66 framework can have a BET surface area anywhere from 1000-1800 m2/g and a pore volume from 0.40-0.90 cm3/g, depending on the degree of defect engineering15,16.
For the measured UiO-66, when using the linear P/P0 range 0.01-0.05, the BET surface area is 1211 m2/g and the C value is 457. The theoretical surface area of a simulated, defect-free UiO-66 is 1200 m2/g14. In a type 1 isotherm, as seen in UiO-66, the BET surface area should be treated as an apparent surface area since the BET model does not confirm the validity of the BET monolayer capacity17. The measured surface area falls within the expected range for UiO-66, and combined with the C value, indicates a microporous structure with uniform monolayer formation and pore filling.
The pore volume of a material is typically analyzed at a P/P0 of 0.80-0.95. If there are macropores present in the material, the nitrogen adsorption isotherm will not be nearly horizontal at P/P0 close to unity, and thus the total pore volume cannot be evaluated17. The pore volume measured in this case would only be the pore volume of the micro and mesopores.
The measured pore volume, taken at a P/P0 of 0.80, of UiO-66 is 0.86 cm3/g. The theoretical pore volume of UiO-66 is 0.77 cm3/g15. The higher pore volume for the UiO-66 sample measured is most likely due to defects present within the UiO-66 structure. Rather than having solely micropores, there are defects present resulting in larger meso- or macro-pores, giving a larger pore volume. This is corroborated with the shape of the nitrogen isotherm where there is a sharp increase and hysteresis at high relative pressures and a type 1-2 isotherm shape.
Often, the measured BET surface area and pore volume of a given material will be within a given range. It has been shown that the repeatability of nitrogen adsorption isotherms and surface area measurements vary widely across the literature19. This is due to variations in the BET range selected, material defects, forgoing repeat experiments, and intrinsic characteristics of the model. Tools like the BET surface identification (BETSI) program can be utilized for an unambiguous assessment of the BET surface area by an automatic selection of the linear range based on extended selection criteria. The BET model was not developed for adsorption in microporous materials, despite it being the standard in material characterization. This is due to the idea of monolayer coverage and idealized adsorption behavior13. The BET model assumes uniform adsorption and a homogenous surface. These assumptions may not hold true for materials with heterogeneous surfaces or very small pores, and thus, the application of the BET model must be evaluated for each given material.
The results of the nitrogen adsorption experiment and analysis indicate the successful formation of a UiO-66 microporous, crystalline structure with slight defects. The calculated surface area and pore volume fall within the range reported in literature15,19, leading to the conclusion that the BET model can be applied to the MOF UiO-66 and can be translated to other nanoporous materials if the given assumptions and conditions apply.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/65716/65716fig01.jpg" /> 
Figure 1: Diagram of adsorption instrument. The sealed sample tube is connected to pressure transducers, a vacuum, and the free space/analysis gas sources. <a href="https://www.jove.com/files/ftp_upload/65716/65716fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/65716/65716fig02.jpg" /> 
Figure 2: Nitrogen adsorption and desorption isotherm for UiO-66 at 77 K. The nitrogen isotherm of the MOF UiO-66 at 77 K where the BET surface area was measured to be 1211 m2/g and the pore volume was measured to be 0.86 cm3/g. <a href="https://www.jove.com/files/ftp_upload/65716/65716fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>BET Area</td>
			<td>1211 m2/g</td>
		</tr>
		<tr>
			<td>Slope</td>
			<td>0.0035 g/cm3 STP</td>
		</tr>
		<tr>
			<td>Y-Intercept</td>
			<td>0.000008 g/cm3 STP</td>
		</tr>
		<tr>
			<td>C</td>
			<td>457</td>
		</tr>
		<tr>
			<td>Monolayer Capacity</td>
			<td>278 cm3/g STP</td>
		</tr>
		<tr>
			<td>Molecular Cross-Sectional Area</td>
			<td>0.1620 nm2</td>
		</tr>
		<tr>
			<td>Correlation Coefficient</td>
			<td>0.9999</td>
		</tr>
	</tbody>
</table>
Table 1: Table indicating the values obtained from the BET analysis of UiO-66 at 77 K. The table includes a summary of the key values obtained from the BET analysis in the range of P/P0 of 0.01-0.05 for the MOF UiO-66. The positive C and y-intercept, along with a correlation coefficient of 0.9999 indicates that an acceptable linear region was selected for BET analysis.

Watch this Scientific Journal Video about Characterizing Porous Materials for Aiding the Development of Robust Metal-Organic Frameworks with Adsorption Behavior at JoVE.com

Author Spotlight: Characterizing Porous Materials for Aiding the Development of Robust Metal-Organic Frameworks with Adsorption Behavior 

This article describes the use of nitrogen porosimetry to characterize metal-organic frameworks, using UiO-66 as a representative material.

Determining Surface Areas and Pore Volumes of Metal-Organic Frameworks

The surface area and pore volume of a metal-organic framework (MOF) can provide insight into its structure and potential applications. Both parameters are ...

determining-surface-areas-and-pore-volumes-of-metal-organic-frameworks

Research

JoVE Journal

Chemistry

6.6K Views.  Georgia Institute of Technology. This article describes the use of nitrogen porosimetry to characterize metal-organic frameworks, using UiO-66 as a representative material. 

Video: Author Spotlight: Characterizing Porous Materials for Aiding the Development of Robust Metal-Organic Frameworks with Adsorption Behavior 

Preparation of Hydrophobic Metal-Organic Frameworks via Plasma Enhanced Chemical Vapor Deposition of Perfluoroalkanes for the Removal of Ammonia

Plasma enhanced chemical vapor deposition (PECVD) of perfluoroalkanes has long been studied for tuning the wetting properties of surfaces. For high surface area microporous materials, such as metal-organic frameworks (MOFs), unique challenges present themselves for PECVD treatments. Herein the protocol for development of a MOF that was previously unstable to humid conditions is presented. The protocol describes the synthesis of Cu-BTC (also known as HKUST-1), the treatment of Cu-BTC with PECVD of perfluoroalkanes, the aging of materials under humid conditions, and the subsequent ammonia microbreakthrough experiments on milligram quantities of microporous materials. Cu-BTC has an extremely high surface area (~1,800 m2/g) when compared to most materials or surfaces that have been previously treated by PECVD methods. Parameters such as chamber pressure and treatment time are extremely important to ensure the perfluoroalkane plasma penetrates to and reacts with the inner MOF surfaces. Furthermore, the protocol for ammonia microbreakthrough experiments set forth here can be utilized for a variety of test gases and microporous materials.

Herein the procedures for plasma enhanced chemical vapor deposition of perfluoroalkanes on microporous materials such as metal-organic frameworks to enhance their stability and hydrophobicity are described. Furthermore, breakthrough testing of milligram quantities of samples is described in detail.

Plasma enhanced chemical vapor deposition (PECVD) of perfluoroalkanes has long been studied for tuning the wetting properties of surfaces. For high ...

Synthesis and Characterization of Functionalized Metal-organic Frameworks

Metal-organic frameworks have attracted extraordinary amounts of research attention, as they are attractive candidates for numerous industrial and technological applications. Their signature property is their ultrahigh porosity, which however imparts a series of challenges when it comes to both constructing them and working with them. Securing desired MOF chemical and physical functionality by linker/node assembly into a highly porous framework of choice can pose difficulties, as less porous and more thermodynamically stable congeners (e.g., other crystalline polymorphs, catenated analogues) are often preferentially obtained by conventional synthesis methods. Once the desired product is obtained, its characterization often requires specialized techniques that address complications potentially arising from, for example, guest-molecule loss or preferential orientation of microcrystallites. Finally, accessing the large voids inside the MOFs for use in applications that involve gases can be problematic, as frameworks may be subject to collapse during removal of solvent molecules (remnants of solvothermal synthesis). In this paper, we describe synthesis and characterization methods routinely utilized in our lab either to solve or circumvent these issues. The methods include solvent-assisted linker exchange, powder X-ray diffraction in capillaries, and materials activation (cavity evacuation) by supercritical CO2 drying. Finally, we provide a protocol for determining a suitable pressure region for applying the Brunauer-Emmett-Teller analysis to nitrogen isotherms, so as to estimate surface area of MOFs with good accuracy.

Synthesis, activation, and characterization of intentionally designed metal-organic framework materials is challenging, especially when building blocks are incompatible or unwanted polymorphs are thermodynamically favored over desired forms. We describe how applications of solvent-assisted linker exchange, powder X-ray diffraction in capillaries and activation via supercritical CO2 drying, can address some of these challenges.

Metal-organic frameworks have attracted extraordinary amounts of research attention, as they are attractive candidates for numerous industrial and ...

Synthesis of a Water-soluble Metal&#8211;Organic Complex Array

We demonstrate a method for the synthesis of a water-soluble multimetallic peptidic array containing a predetermined sequence of metal centers such as Ru(II), Pt(II), and Rh(III). The compound, named as a water-soluble metal-organic complex array (WSMOCA), is obtained through 1) the conventional solution-chemistry-based preparation of the corresponding metal complex monomers having a 9-fluorenylmethyloxycarbonyl (Fmoc)-protected amino acid moiety and 2) their sequential coupling together with other water-soluble organic building units on the surface-functionalized polymeric resin by following the procedures originally developed for the solid-phase synthesis of polypeptides, with proper modifications. Traces of reactions determined by mass spectrometric analysis at the representative coupling steps in stage 2 confirm the selective construction of a predetermined sequence of metal centers along with the peptide backbone. The WSMOCA cleaved from the resin at the end of stage 2 has a certain level of solubility in aqueous media dependent on the pH value and/or salt content, which is useful for the purification of the compound.

A potential general method for the synthesis of water-soluble multimetallic peptidic arrays containing a predetermined sequence of metal centers is presented.

We demonstrate a method for the synthesis of a water-soluble multimetallic peptidic array containing a predetermined sequence of metal centers such as ...

Microfluidic-based Synthesis of Covalent Organic Frameworks (COFs): A Tool for Continuous Production of COF Fibers and Direct Printing on a Surface

Covalent Organic Frameworks (COFs) are a class of porous covalent materials which are frequently synthesized as unprocessable crystalline powders. The first COF was reported in 2005 with much effort centered on the establishment of new synthetic routes for its preparation. To date, most available synthetic methods for COF synthesis are based on bulk mixing under solvothermal conditions. Therefore, there is increasing interest in developing systematic protocols for COF synthesis that provide for fine control over reaction conditions and improve COF processability on surfaces, which is essential for their use in practical applications. Herein, we present a novel microfluidic-based method for COF synthesis where the reaction between two constituent building blocks, 1,3,5-benzenetricarbaldehyde (BTCA) and 1,3,5-tris(4-aminophenyl)benzene (TAPB), takes place under controlled diffusion conditions and at room temperature. Using such an approach yields sponge-like, crystalline fibers of a COF material, hereafter called MF-COF. The mechanical properties of MF-COF and the dynamic nature of the approach allow the continuous production of MF-COF fibers and their direct printing onto surfaces. The general method opens new potential applications requiring advanced printing of 2D or 3D COF structures on flexible or rigid surfaces.

Microfluidic-based Synthesis of Covalent Organic Frameworks COFs: A Tool for Continuous Production of COF Fibers and Direct Printing on a Surface

We present a novel microfluidic-based method for synthesis of covalent organic frameworks (COFs). We demonstrate how this approach can be used to produce continuous COF fibers, and also 2D or 3D COF structures on surfaces.

Covalent Organic Frameworks (COFs) are a class of porous covalent materials which are frequently synthesized as unprocessable crystalline powders. The ...

Surface Functionalization of Metal-Organic Frameworks for Improved Moisture Resistance

Metal-organic frameworks (MOFs) are a class of porous inorganic materials with promising properties in gas storage and separation, catalysis and sensing. However, the main issue limiting their applicability is their poor stability in humid conditions. The common methods to overcome this problem involve the formation of strong metal-linker bonds by using highly charged metals, which is limited to a number of structures, the introduction of alkylic groups to the framework by post-synthetic modification (PSM) or chemical vapour deposition (CVD) to enhance overall hydrophobicity of the framework. These last two usually provoke a drastic reduction of the porosity of the material. These strategies do not permit to exploit the properties of the MOF already available and it is imperative to find new methods to enhance the stability of MOFs in water while keeping their properties intact. Herein, we report a novel method to enhance the water stability of MOF crystals featuring Cu2(O2C)4&#160;paddle-wheel units, such as HKUST (where HKUST stands for Hong Kong University of Science &#38; Technology), with the catechols functionalized with alkyl and fluoro-alkyl chains. By taking advantage of the unsaturated metal sites and the catalytic catecholase-like activity of CuII ions, we are able to create robust hydrophobic coatings through the oxidation and subsequent polymerization of the catechol units on the surface of the crystals under anaerobic and water-free conditions without disrupting the underlying structure of the framework. This approach not only affords the material with improved water stability but also provides control over the function of the protective coating, which enables the development of functional coatings for the adsorption and separations of volatile organic compounds. We are confident that this approach could also be extended to other unstable MOFs featuring open metal sites.

Robust functional catechol coatings were produced in one step by direct reaction of the material known as HKUST with synthetic catechols under anaerobic conditions. The formation of homogeneous coatings surrounding the entire crystal is ascribed to the biomimetic catalytic activity of Cu(II) dimers on the external surface of the crystals.

Metal-organic frameworks (MOFs) are a class of porous inorganic materials with promising properties in gas storage and separation, catalysis and sensing. ...

Electrophoretic Crystallization of Ultrathin High-performance Metal-organic Framework Membranes

We report the synthesis of thin, highly intergrown, polycrystalline metal-organic framework (MOF) membranes on a wide range of unmodified porous and non-porous supports (polymer, ceramic, metal, carbon, and graphene). We developed a novel crystallization technique, which is termed the ENACT approach: the electrophoretic nuclei assembly for the crystallization of highly intergrown thin films (ENACT). This approach allows for a high density of heterogeneous nucleation of MOFs on a chosen substrate via the electrophoretic deposition (EPD) directly from the precursor sol. The growth of well-packed MOF nuclei leads to a highly intergrown polycrystalline MOF film. We show that this simple approach can be used for the synthesis of thin, intergrown zeolite imidazole framework (ZIF)-7 and ZIF-8 films. The resulting 500 nm-thick ZIF-8 membranes show a considerably high H2 permeance (8.3 x 10-6 mol m-2 s-1 Pa-1) and ideal gas selectivities (7.3 for H2/CO2, 15.5 for H2/N2, 16.2 for H2/CH4, and 2655 for H2/C3H8). An attractive performance for C3H6/C3H8 separation is also achieved (a C3H6 permeance of 9.9 x 10-8 mol m-2 s-1 Pa-1 and a C3H6/C3H8 ideal selectivity of 31.6 at 25 &#176;C). Overall, the ENACT process, owing to its simplicity, can be extended to synthesize intergrown thin films of a wide range of nanoporous crystalline materials.

A simple, reproducible, and versatile approach for the synthesis of intergrown, polycrystalline metal-organic framework membranes on a wide range of unmodified porous and non-porous supports is presented.

We report the synthesis of thin, highly intergrown, polycrystalline metal-organic framework (MOF) membranes on a wide range of unmodified porous and ...

Surface Properties of Synthesized Nanoporous Carbon and Silica Matrices

In this work, we report the synthesis and characterization of ordered nanoporous carbon material (also called ordered mesoporous carbon material [OMC]) with a 4.6 nm pore size, and ordered silica porous matrix, SBA-15, with a 5.3 nm pore size. This work describes the surface properties of nanoporous molecular sieves, their wettability, and the melting behavior of D2O confined in the differently ordered porous materials with similar pore sizes. For this purpose, OMC and SBA-15 with highly ordered nanoporous structures are synthesized via impregnation of the silica matrix by applying a carbon precursor and by the sol-gel method, respectively. The porous structure of investigated systems is characterized by an N2 adsorption-desorption analysis at 77 K. To determine the electrochemical character of the surface of synthesized materials, potentiometric titration measurements are conducted; the obtained results for OMC shows a significant pHpzc shift toward the higher values of pH, relative to SBA-15. This suggests that investigated OMC has surface properties related to oxygen-based functional groups. To describe the surface properties of the materials, the contact angles of liquids penetrating the studied porous beds are also determined. The capillary rise method has confirmed the increased wettability of the silica walls relative to the carbon walls and an influence of the pore roughness on the fluid/wall interactions, which is much more pronounced for silica than for carbon mesopores. We have also studied the melting behavior of D2O confined in OMC and SBA-15 by applying the dielectric method. The results show that the depression of the melting temperature of D2O in the pores of OMC is about 15 K higher relative to the depression of the melting temperature in SBA-15 pores with a comparable 5 nm size. This is caused by the influence of adsorbate/adsorbent interactions of the studied matrices.

Here we report the synthesis and characterization of ordered nanoporous carbon (with a 4.6 nm pore size) and SBA-15 (with a 5.3 nm pore size). The work describes the surface and textural properties of nanoporous molecular sieves, their wettability, and the melting behavior of D2O confined in the materials.

In this work, we report the synthesis and characterization of ordered nanoporous carbon material (also called ordered mesoporous carbon material [OMC]) ...

Development of Heterogeneous Enantioselective Catalysts using Chiral Metal-Organic Frameworks (MOFs)

Substrate size discrimination by the pore size and homogeneity of the chiral environment at the reaction sites are important issues in the validation of the reaction site in metal-organic framework (MOF)&#8211;based catalysts in an enantioselective catalytic reaction system. Therefore, a method of validating the reaction site of MOF-based catalysts is necessary to investigate this issue. Substrate size discrimination by pore size was accomplished by comparing the substrate size versus the reaction rate in two different types of carbonyl-ene reactions with two kinds of MOFs. The MOF catalysts were used to compare the performance of the two reaction types (Zn-mediated stoichiometric and Ti-catalyzed carbonyl-ene reactions) in two different media. Using the proposed method, it was observed that the entire MOF crystal participated in the reaction, and the interior of the crystal pore played an important role in exerting chiral control when the reaction was stoichiometric. Homogeneity of the chiral environment of MOF catalysts was established by the size control method for a particle used in the Zn-mediated stoichiometric reaction system. The protocol proposed for the catalytic reaction revealed that the reaction mainly occurred on the catalyst surface regardless of the substrate size, which reveals the actual reaction sites in MOF-based heterogeneous catalysts. This method for reaction site validation of MOF catalysts suggests various considerations for developing heterogeneous enantioselective MOF catalysts.

Development of Heterogeneous Enantioselective Catalysts using Chiral Metal-Organic Frameworks MOFs

Here, we present a protocol for active site validation of metal-organic framework catalysts by comparing stoichiometric and catalytic carbonyl-ene reactions to find out whether a reaction takes place on the inner or outer surface of metal-organic frameworks.

Substrate size discrimination by the pore size and homogeneity of the chiral environment at the reaction sites are important issues in the validation of ...

Synthesis of Single-Crystalline Core-Shell Metal-Organic Frameworks

Because of their designability and unprecedented synergistic effects, core-shell metal-organic frameworks (MOFs) have been actively examined recently. However, the synthesis of single-crystalline core-shell MOFs is very challenging, and thus a limited number of examples have been reported. Here, we suggest a method of synthesizing single-crystalline HKUST-1@MOF-5 core-shells, which is HKUST-1 at the center of MOF-5. Through the computational algorithm, this pair of MOFs was predicted to have the matched lattice parameters and chemical connection points at the interface. To construct the core-shell structure, we prepared the octahedral- and cubic-shaped HKUST-1 crystals as a core MOF, in which the (111) and (001) facets were mainly exposed, respectively. Via the sequential reaction, the MOF-5 shell was well-grown on the exposed surface, showing a seamless connect interface, which resulted in the successful synthesis of single-crystalline HKUST-1@MOF-5. Their pure phase formation was proved by optical microscopic images and powder X-ray diffraction (PXRD) patterns. This method presents the potential of and insights into the single-crystalline core-shell synthesis with different kinds of MOFs.

Here, we demonstrate a protocol for the two-step synthesis of single-crystalline core-shells using a non-isostructural metal-organic framework (MOF) pair, HKUST-1 and MOF-5, which have well-matched crystal lattices.

Because of their designability and unprecedented synergistic effects, core-shell metal-organic frameworks (MOFs) have been actively examined recently. ...

A Technical Guide for Performing Spectroscopic Measurements on Metal-Organic Frameworks

Metal-organic frameworks (MOFs) offer a unique platform to understand light-driven processes in solid-state materials, given their high structural tunability. However, the progression of MOF-based photochemistry has been hindered by the difficulty in spectrally characterizing these materials. Given that MOFs are typically larger than 100 nm in size, they are prone to excessive light scatter, thereby rendering data from valuable analytical tools like transient absorption and emission spectroscopy nearly uninterpretable. To gain meaningful insights of MOF-based photo-chemical and physical processes, special consideration must be taken toward properly preparing MOFs for spectroscopic measurements, as well as the experimental setups that garner higher quality data. With these considerations in mind, the present guide provides a general approach and set of guidelines for the spectroscopic investigation of MOFs. The guide addresses the following key topics: (1) sample preparation methods, (2) spectroscopic techniques/measurements with MOFs, (3) experimental setups, (3) control experiments, and (4) post-run stability characterization. With appropriate sample preparation and experimental approaches, pioneering advancements toward the fundamental understanding of light-MOF interactions are significantly more attainable.

Here, we use a polymer stabilizer to prepare metal-organic framework (MOF) suspensions that exhibit markedly decreased scatter in their ground-state and transient absorption spectra. With these MOF suspensions, the protocol provides various guidelines to characterize the MOFs spectroscopically to yield interpretable data.