Rapid Whole-Mount High-Resolution Imaging of Small Animal Vasculature for Quantitative Studies

Summary

This protocol introduces a rapid method for quantitative whole-mount three-dimensional vascular imaging using light-sheet fluorescence microscopy. The efficacy of the method is demonstrated using the pharyngeal arch artery system of the chick embryo model, with hemodynamic forces quantified via computational fluid dynamics.

Abstract

In small animal models of cardiovascular development and diseases, subject-specific computational simulations of blood flow enable quantitative assessments of hemodynamic metrics that are difficult to measure experimentally. Computational fluid dynamic simulations shed light on the critical roles of mechanics in cardiovascular function and disease progression. Acquiring high-quality volumetric images of the vessels of interest is central to the accuracy and reproducibility of morphological measurement and flow quantitation results. This study proposes a rapid, cost-effective, and accessible method for whole-mount high-resolution imaging of small animal vasculature using light-sheet fluorescence microscopy. The modified iDISCO+ (immunolabeling-enabled three-dimensional imaging of solvent-cleared organs) light-sheet sample preparation protocol involves (1) labeling vasculature with a fluorescent agent, (2) preserving the sample, and (3) rendering the sample transparent. Unlike classical iDISCO+, which uses immunohistochemical staining, the authors label vascular endothelium with FITC-tagged poly-L-lysine, an affordable non-specific fluorescent dye that is highly resistant to photo-bleaching, in a process termed "endo-painting." The rapid labeling reduces sample preparation time from approximately four weeks to less than 3 days. Furthermore, the use of minimally hazardous solvent ethyl cinnamate (ECi) as the clearing agent and imaging solution makes the samples safer to handle and compliant with a wider range of imaging facilities. The proposed protocol is applied to obtain highly resolved light-sheet fluorescence microscopy image stacks of the cardiovascular system in chick embryos ranging from day 3 (HH18) to day 8 (HH34). This study further demonstrates the suitability of this method for vascular quantitation through 3D reconstruction and computational hemodynamic modeling of a day 5 (HH 26) chick embryo.

Introduction

Volumetric imaging is necessary for accurate studies of cardiovascular physiology and disease. Quantitative imaging produces high-resolution image stacks with intact volumetric dimensions. Samples must both be preserved to maintain their in-vivo morphology and lumen volume as well as imaged in a uniform high resolution capacity. From high-resolution imaging stacks, the user can generate high-fidelity three-dimensional vascular renderings that allow for a complete display of vessel shapes, structure, and connectivity¹.

Cardiovascular structures possess complex three-dimensional anatomical features that cannot be accurately captured when examining them through a two-dimensional, disjointed lens. Stereoscope widefield morphological imaging and histological sections are inadequate in capturing complex three-dimensional variations^1,2,3. Micro and nano-computed tomography images are the gold standard for quantitative small animal volumetric imaging^1,4, but are not widely accessible or adopted among the biological community. Recent innovations in tissue clearing and whole organ/small animal microscopy have allowed for quantitative applications of whole mount clearing and vascular labeling techniques^5,6,7. Tissue-clearing works to homogenize the scattering of light in tissue samples, thereby reducing delays in light propagation through the medium by lowering the chance of light scattering or absorption. High transparency requires stringent tissue processing that may affect the antigenicity or brightness of fluorescence signal labeling⁸. Light-sheet microscopy has emerged as a fast, powerful imaging tool widely adopted by biologists⁹, offering a gain of speed several orders of magnitude over scanning microscopes and the capacity to image samples over 1 cm in size. Through light-sheet fluorescence microscopy (LSFM), a laser illuminates a sample cross-section with increased speed and depth compared to confocal microscopy; for this reason, the method requires high sample transparency.

Here, the authors adapt recent iDISCO+ clearing methods, combining them with endo-painting¹⁰ in the chick embryo animal model to showcase the method's efficacy from early to late cardiovascular development. iDISCO (immunolabeling-enabled three-dimensional imaging of solvent-cleared organs) is an organic solvent-based clearing method, which, unlike aqueous clearing-based methods, is not subject to imaging artifacts caused by solvent evaporation. iDISCO differs from iDISCO+ in that the tetrahydrofuran dehydration step of the former (iDISCO) is replaced by a milder Methanol dehydration followed by a lipid extraction step (iDISCO+). Advantages of the iDISCO+ clearing method include immunolabeling of large adult samples and embryos, low tissue shrinkage, and high transparency^8,11. Importantly, iDISCO+ allows for the generation of high-resolution image stacks, expanding upon traditional biology immunolabeling techniques to gain information over large organ samples or an entire embryo rather than being limited to the sampling of small regions that lack information on the whole tissue-level organization, as with traditional histology⁹. Disadvantages of iDISCO+ include the fact that genetically encoded fluorescent proteins are not preserved¹¹. The tissue labeling method of endo-painting was first introduced as a high-throughput screening for cardiovascular defects using HH31-HH36 chick embryo hearts which were perfused with 0.5 mg/ml of FITC-poly-L-lysine in the left ventricular apex. The dye was allowed to bind for 4 min before fixation and storage¹⁰.

The present study found that the same FITC-poly-L-lysine concentration could be used for a broader range of embryos (HH18 - HH34) but found the ideal fixation time to vary (from 5-10 min) to ensure brightly labeled vessels. Users of the present endo-DISCO technique may want to adjust dye concentration (decreasing by 0.1 mg/mL at a time) should the solution prove too viscous to label all desired vessels, but are encouraged to first adjust the fixation time and optimize muscular contraction of the left ventricle before adjusting dye concentration. The authors attempted endo-painting with a concentration of 0.1 mg/mL and found that while the dye more easily spread through small vessels, it was more easily washed away upon PFA perfusion. The authors show that the high-resolution imaging stacks generated through the present technique are of sufficient quality for computational hemodynamic modeling. Blood flow paths and corresponding hemodynamic forces, including pressure and wall shear stress distributions, occur in complex localized patterns that can only be resolved through computational flow simulations^1,12. These biomechanical forces affect the behavior of adjacent cardiovascular tissues and trigger vascular adaptation, growth, and remodeling¹³. Understanding local hemodynamic force values sheds critical light on the mechanistic regulators of cardiovascular function and disease initiation or progression².

Protocol

The Office of Laboratory Animal Welfare interprets Public Health Service policy as applying to the chick model as a "vertebrate animal" only after hatching. These embryos are similarly exempt from Institutional Animal Care and Use Committee (IACUC) jurisdiction. The relevant National Institutes of Health frequently asked questions can be accessed at: http://grants.nih.gov/grants/olaw/faqs.htm#ApplicabilityofthePHSPolicy.

1. Embryo collection, labeling and fixation

1. Fashion pulled 0.75 inner diameter glass capillary rods into cut microneedles using a microforge^1,12.
   NOTE: The size of the tip required depends on the animal age/flow rate desired. The microneedle can alternatively be cut using microdissection forceps or scissors with greatly reduced precision.
2. Warm Tyrode's solution to approximately 38^°C.
3. Dissolve FITC poly-L-lysine solid in Tyrode's solution to prepare a 0.5 mg/mL stock solution.
   NOTE: This concentration is optimized for labeling chick embryo arteries. The optimal concentration for other tissue types may vary. The extra stock solution should be stored at -20 °C.
4. Dissect out the avian embryo (ranging from HH18 (day 3) to HH34 (day 8) for the present chick cardiac study) from the egg yolk by cutting around the embryo with curved tip scissors and using a transfer pipette or a spatula to transfer the embryo to a 35 mm Petri dish filled with warm Tyrode's solution.
5. Carefully remove the chorionic and allantoic membranes enveloping the embryo and the pericardium membrane around the heart with fine-tip forceps by making tiny (~0.1 mm) incisions in the membranes and pulling them away from the embryo.
6. Transfer the embryo to a new, clean Petri dish filled with warm Tyrode's solution to keep the heart beating.
7. Fill a 5 mL plastic syringe with warm Tyrode's solution. Trim off the wide end of a 0-20 μL plastic pipette tip and attach it to the flat tip of the syringe. The syringe has now been extended to the fine pipette tip diameter.
8. Construct an "injection line," by attaching a segment of 0.03-inch inner diameter silicone tubing to the newly secured pipette tip-syringe apparatus (step 1.7). Attach a glass capillary microneedle to the opposite end of the tubing.
9. Mount the microneedle onto the microinjection holder attached to a micromanipulator. Purge the silicone tubing and microneedle of air bubbles.
10. Using the micromanipulator, insert the needle into the apex of the heart and perfuse the embryo^1,12by slowly injecting Tyrode's solution into the heart. Continue perfusing the embryo until it is largely cleared of blood.
11. Use the micromanipulator to pull the needle and injection line back from its insertion site and orient the needle so that it will not be disturbed during the preparation of the next injection line. Remove the silicon tubing from the needle and syringe.
    NOTE: Some users may find it optimal to keep the needle attached to the heart, in which case the user should remove the silicon tubing between the needle and syringe, while keeping the needle in place.
12. Perform endo-painting to label the vascular endothelium with green fluorescence.
    1. Using a micropipette, load 20-40 μL of FITC poly-L-lysine stock solution into the silicone tubing, careful not to create air bubbles ahead of the FITC liquid barrier.
    2. Reattach the syringe filled with Tyrode's solution and use the micromanipulator to slowly inject into the apex of the heart, reinserting the needle if necessary. Remove the needle after the FITC poly-L-lysine has been diffused and before any air bubbles enter the heart.
    3. Let FITC poly-L-lysine sit in the embryo for 5-10 min.
       NOTE: (optional quality check) To verify fluorescence, take a picture with a fluorescent stereo or macroscope. The picture may be used to help determine a dehydration factor after embryo clearing is completed.
13. Fill a 5 mL syringe with 4% paraformaldehyde (PFA) and attach it to the silicon injection tubing for a third injection step.
14. Perfuse the embryo^1,12 with 4% PFA until all cardiovascular structures are at full volume capacity and the tissue starts to become more opaque.
15. Gently load the embryo into a 2-5 mL vial filled with enough 4% PFA to cover the sample. Take care not to deform the embryo excessively.
    NOTE: Choose a large enough vial for the sample of interest to avoid crushing or deforming the sample.
16. Incubate the embryo overnight at 4 °C with a shaker.

2. Embryo dehydration and clearing

1. Carefully pipette out the 4% PFA.
   NOTE: From this point on, avoid direct contact with the embryo to prevent tissue damage or deformation.
2. To wash the embryo, incubate the embryo in fresh phosphate buffer solution (PBS) at room temperature for 30 min while gently shaking. Repeat two additional times for a total of 3 washes.
3. Begin dehydrating the embryo in a fume hood. Carefully pipette out the PBS and incubate the embryo in a graded series of 5 methanol incubations at room temperature for 1 h each: 20%, 40%, 60%, 80%, and 100% methanol concentration.
4. Leave the embryo in fresh 100% methanol at room temperature overnight.
   NOTE: (Optional stopping point). Embryos can be stored at -20 °C in 100% methanol for later use for up to 6 months.
5. In the fume hood, begin the lipid removal procedure. Incubate embryo in a 2:1 (volume to volume) DCM: methanol solution at room temperature for 3 h, gently shaking.
   CAUTION: DCM is toxic and must be handled in the fumehood. Take extra precautions when working with DCM. Double gloves may help provide an extra barrier.
6. Take Ethyl cinnamate (ECi) out of 4 °C and leave it at room temperature to thaw.
7. Wash embryos in fresh 100% DCM at room temperature for 15 min, shaking. Repeat 100% DCM wash to achieve a total of 2 washes.
8. Pipette out DCM and incubate the embryo in 100% ECi. Leave the embryo in ECi until it clears in approximately 1 h. Gently shake the tube if necessary.
9. (Optional verification step) Examine the quality of clearing and vessel staining with a fluorescent stereo or macroscope. Take a picture of the embryo to determine the stage/age-specific dehydration scaling factor.
10. Store the cleared embryo at 4 °C for up to 6 months until ready to image, keeping the embryo protected from light.

3. Acquisition of data

1. To image embryos, use a light-sheet fluorescent microscope. Affix the head of an optically cleared embryo to a glass capillary using superglue gel.
2. Mount the glass capillary to the sample holder, fill the imaging chamber with ECi, and lower the embryo in the imaging chamber.
3. Adjust the parameters and perform imaging.

4. Quantitative application: 3D reconstruction and computational fluid dynamic modeling

NOTE: In these steps, light-sheet generated high-resolution image stacks are loaded in the open-source software SimVascular¹⁴ for 3D anatomical reconstruction and computational fluid dynamic modeling. Detailed tutorials exist on the SimVascular website (see Table of Materials). Reconstruction consists of creating pathlines in the vessels of interest, creating 2D segmentations along the pathlines, and combining lofted segmentations into a 3D solid model. Computational modeling consists of preparing a meshed geometry, defining boundary conditions, and running simulations.

1. Create a new SVProject under File and upload a high-resolution light-sheet imaging stack by right-clicking on Images and then clicking on add/replace image.
2. Follow the software tutorial steps to reconstruct vascular anatomies in silico.
   1. Create a pathline by right-clicking on Paths and selecting create path. Place path markers along a vessel of interest. Repeat for each vessel of interest.
   2. For each pathline created, trace 2D vessel cross sections by right-clicking on Segmentations and selecting the Create Contour Group. Select the vessel path and double-click on the vessel name under Segmentation to begin manual segmentation.
   3. Once all vessels have been segmented, create a model by right-clicking on Models and then selecting create model. Select PolyData type, enter a model name, click on Create Solid Model, and select all the segmentations that should be part of the model.
3. Mesh the geometry by running the Tetgen mesher built into SimVascular SVMesher. Define a max edge size and perform both surface and volume meshing.
   NOTE: Choose a mesh size that can resolve fine geometric details and localized hemodynamic variabilities in the vessel. Start with the Estimate a global mesh size button. A mesh convergence study may be necessary when finalizing simulations.
4. Set up a computational blood flow simulation using the SimVascular Solver. Create simulation files by right-clicking on Simulations and selecting Create Simulation Job. Adjust basic parameters and select inlet and outlet BCs for specific boundary conditions.
   1. Adjust Solver parameters, navigate to the Create Files and Run simulation tab, select mesh file, click on Create Data Files for Simulation.
5. Launch the simulation using a high-performance computing workstation or supercomputer.

Results

The rapid whole-mount high-resolution imaging protocol presented here (Figure 1, Table 1) produces clearly outlined vessel lumens as shown in Figure 2, Figure 3, and Figure 4, where the chick embryo vasculature endothelium is GFP fluorescent and therefore outlined in green across embryo stages from early to mature heart development (Figure 4). It is important to find the ri...

Discussion

The ability to study biology in 3D is critical to an accurate understanding of morphological complexity, inner organ structure, and vascular connections. Accurate and reliable 3D vascular images are also central to subject-specific computational hemodynamic simulations, which are often the only reliable means of quantifying key hemodynamic parameters such as wall shear stress and pressure distribution. Here, the authors introduce a rapid and accessible sample preparation method for high-resolution 3D vascular imaging in ...

Materials

Name	Company	Catalog Number	Comments
#5 forceps	Fine Science Tools	11252-30
#55-forceps	Fine Science Tools	11295-51
0.03 inch inner diameter silicone tubing	VWR	32829-182
20 μL pipette tips	VWR	76322-134
35 mm Petri dish	VWR	10799-192
5 mL plastic syringe	VWR	BD 309646
Dichloromethane (DCM)	Sigma-Aldrich	270997	Refer to MSDS. Stored in side cabinet under fume hood
Ethyl cinnamate (ECi)	Sigma-Aldrich	112372	Stored at 4 °C
Fine Curved scissors	Fine Science Tools	14061-09
FITC-poly-L-lysine	Sigma-Aldrich	P3069	Store at -20 °C (powder, stock solution), 4ºC (working solution)
Fluoresent microscope	EVIDENT SCIENTIFIC	MVX10
Glass capillary tubes (0.75 mm ID)	Sutter Instrument	FG-GB100-75-10
Lightsheet microscope	Zeiss	Z.1 system
Methanol	Sigma-Aldrich	M1775	Refer to MSDS. Stored in flammable cabinet under fume hood
Microforge	Narishige International USA, Inc.	MF2
Micromanipulator	World Percision Instrrument	M3301R
Paraformaldehyde (PFA) 4%	Thermo Scientific	J19943.K2	Refer to MSDS. Stored at -20 °C (powder), 4 °C (4% working solution)
Phosphate buffered saline (PBS)	Cytiva	SH30256.01	Stored on benchtop
SimVascular			open source software www.simvascular.org
Tyrode’s Solution			Made in-house