The authors would like to acknowledge the BPI PIAVE AUTONOTEX grant for the financial support.

섬유 1. 패터닝 실시 폴리머 <ol><li> 과정에서 취급이 용이 평면 표면에 10 ㎝의 섬유 시트를 고정한다. 섬유의 경우, 300 ㎛의 두께와 50 % 니트 방향 연신 능력쪽으로 100 % 연동 니트 폴리 에스테르 직물을 사용한다. </li><li> 패터닝 디자인을 포함하는 마스크를 만들기 위해, 125 ㎛의 두께의 폴리이 미드 필름을 사용한다; 패턴의 예는도 1에 도시되어있다. <ol><li> 패턴 폴리이 미드 마스크 (10)에 레이저 커터 (예를 들어, Protolaser S, LPKF)를 사용하여; 전극 패턴의 디자인은도 1에 도시되어있다. </li><li> 코트 PDMS 제제 (10 : 1베이스 에이전트 비율 경화) 200 ㎛ 또는 (A)에서의 습윤 필름 두께로 자동 테이프 캐스팅 도구 (K 제어 프린트 코터, 닥터 블레이드)을 사용하여 마스크 (폴리이 미드 막)의 위에 6m / 분의 도포 속도. 3cm × 5 cm의 마스크 약 0.5 mL를 사용합니다. 일을 수행흄 후드에서 과정입니다. </li></ol></li><li> 조심스럽게 PDMS 코팅 마스크 직물을 전송합니다. PDMS의 완전 섬유 구조체에 흡수되어야 후 10 분 동안 남겨. </li><li> 10 분 동안 100 ℃에서 공기 오븐에서 샘플을 경화. </li><li> 전도성 중합체를 제조 : PEDOT : PSS 분산액 (80 ㎖), 에틸렌 글리콜 (20 ㎖), 4- 도데 실 벤젠 설 폰산 (40 μL) 및 흄 후드의 3- 메타 크릴 (1 mL)을 첨가 하였다. </li><li> 브러쉬 코트 PEDOT : 용액의 균일 침투 될 때까지 섬유의 PDMS없는 영역 PSS 용액이 얻어진다. 균일 한 패턴 색상을 달성하기 위해이 단계를 반복합니다. 약 1 ㎖ / cm 2를 적용합니다. </li><li> PSS의 해결 방법 : PEDOT를 건조 1 시간 동안 110 ° C에서 직물을 치료. 나일론과 같은 고온 처리에 민감한 직물 60 ℃로 온도를 감소시킨다. </li></ol> 2. 유기 소자의 제조 참고 : 제 1 describ의 프로토콜직물에 전도성 물질의 선택적 증착을 에스. 다음 섹션에서는 스트레치 센서, OECT 트랜지스터, 피부 전극 및 정전 용량 센서와 같은 유기 소자를 제작하는 데 필요한 추가 단계를 설명합니다. <ol><li> 제 1 항에 기재된 바와 같이, 섬유에도 3a에 도시 된 신축성 센서, 패턴 전극 라인을 제조하기 위해, 1.1-1.5 단계. 주 : 패턴 디자인의 예는도 3a에 도시되어있다. 이러한 센서의 제조는 추가 단계가 필요하지 않습니다. </li><li> 도 3b에 도시 된 트랜지스터 디자인을 제조하기 위해, 패턴을 제 1에 기재된 단계에 따라 나일론 직조 리본 트랜지스터 어레이 살짝 PDMS 소둔 및 PEDOT을 수정 PSS 60 ℃에서 경화시켜 나일론의 열 열화를 방지하기위한 조치를 경화 긴 시간 동안 C. </li><li> 도 3c에 도시 된 피부 전극의 제조, 들면, 증착PSS 직물 : 패턴 PEDOT에 이온 젤. <ol><li> 이온 성 액체 젤 혼합물을 이온 성 액체를 포함하는, 1- 에틸 -3- 메틸이 미다 졸륨 에틸 술 페이트 준비; 가교제, 폴리 (에틸렌 글리콜) 디 아크릴 레이트; 각각 0.6 / 0.35 / 0.05의 (v / v)의 비율로 광개시제, 2- 히드 록시 -2- methylpropiophenone. </li><li> 코트 PEDOT : 이온 성 액체 (20 μL / cm 2)와 PSS 전극과 드롭 주조에 의해 단계 2.3.1 (25 μL / cm 2)에서 이온 성 액체 젤 혼합물을 추가합니다. </li><li> 겔이 응고 될 때까지 10 ~ 15 분 동안 가교 반응을 개시하기 위해 UV 광 (365 ㎚)에 노출시킨다. 흄 후드에서이 단계를 수행합니다. UV 노출시 자외선 보호 케이지를 사용합니다. </li></ol></li><li> 정전 용량 식 센서의 제조에, PEDOT를 사용하는 절연 재료 (도 3D)와 절연 PSS 섬유 전극. <ol><li> 키보드와 같은 절연 시키 PEDOT 다음 PDMS를 사용하는 PSS 전극; 키보드 설계는도 2b &lt;에서 알 수있는/ strong&gt;을. 직물의 맨 위에 PDMS 제제를 분배하고, 스퀴지 초과를 제거합니다. </li><li> 10 분 동안 100 ° C의 오븐에서 직물을 놓는다. 흄 후드에서이 단계를 수행합니다. </li></ol></li></ol>

<ol>
	<li>Poupyrev, I., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Project+Jacquard:Interactive+Digital+Textiles+at+Scale.">Project Jacquard:Interactive Digital Textiles at Scale.</a> Proceedings of the 2016 CHI Conference on Human Factors in Computing Systems - CHI '16. , 4216-4227 (2016).</li><li>Takamatsu, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transparent+conductive-polymer+strain+sensors+for+touch+input+sheets+of+flexible+displays.">Transparent conductive-polymer strain sensors for touch input sheets of flexible displays.</a> J. Micromech. Microeng. 20, 075017 (2010).</li><li>Patel, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+review+of+wearable+sensors+and+systems+with+application+in+rehabilitation.">A review of wearable sensors and systems with application in rehabilitation.</a> J. Neuroeng. Rehabil. 9, 21 (2012).</li><li>Bandodkar, A. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epidermal+tattoo+potentiometric+sodium+sensors+with+wireless+signal+transduction+for+continuous+non-invasive+sweat+monitoring.">Epidermal tattoo potentiometric sodium sensors with wireless signal transduction for continuous non-invasive sweat monitoring.</a> Biosens. Bioelectron. 54, 603-609 (2014).</li><li>Owens, R. M., Malliaras, G. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Organic+Electronics+at+the+Interface+with+Biology.">Organic Electronics at the Interface with Biology.</a> MRS Bull. 35 (6), 449-456 (2010).</li><li>Krebs, F. C., Biancardo, M., Winther-Jensen, B., Spanggard, H., Alstrup, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Strategies+for+incorporation+of+polymer+photovoltaics+into+garments+and+textiles.">Strategies for incorporation of polymer photovoltaics into garments and textiles.</a> Sol. Energy Mater. Sol. Cells. 90, 1058-1067 (2006).</li><li>Cherenack, K., Zysset, C., Kinkeldei, T., M&#252;nzenrieder, N., Tr&#246;ster, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Woven+electronic+fibers+with+sensing+and+display+functions+for+smart+textiles.">Woven electronic fibers with sensing and display functions for smart textiles.</a> Adv. Mater. 22, 5178-5182 (2010).</li><li>Hamedi, M., Forchheimer, R., Ingan&#228;s, O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Towards+woven+logic+from+organic+electronic+fibres.">Towards woven logic from organic electronic fibres.</a> Nat. Mater. 6, 357-362 (2007).</li><li>Bao, L., Li, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Towards+Textile+Energy+Storage+from+Cotton+T-Shirts.">Towards Textile Energy Storage from Cotton T-Shirts.</a> Adv. Mater. 24, 3246-3252 (2012).</li><li>Takamatsu, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Direct+patterning+of+organic+conductors+on+knitted+textiles+for+long-term+electrocardiography.">Direct patterning of organic conductors on knitted textiles for long-term electrocardiography.</a> Sci. Rep. 5, 15003 (2015).</li><li>Yamada, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+stretchable+carbon+nanotube+strain+sensor+for+human-motion+detection.">A stretchable carbon nanotube strain sensor for human-motion detection.</a> Nat. Nanotechnol. 6, 296-301 (2011).</li><li>Shim, N. Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=All-plastic+electrochemical+transistor+for+glucose+sensing+using+a+ferrocene+mediator.">All-plastic electrochemical transistor for glucose sensing using a ferrocene mediator.</a> Sensors. 9, 9896-9902 (2009).</li><li>Takamatsu, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Wearable+Keyboard+Using+Conducting+Polymer+Electrodes+on+Textiles.">Wearable Keyboard Using Conducting Polymer Electrodes on Textiles.</a> Adv. Mater. 28, 4485-4488 (2016).</li><li>O'Connor, T. F., Rajan, K. M., Printz, A. D., Lipomi, D. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Toward+organic+electronics+with+properties+inspired+by+biological+tissue.">Toward organic electronics with properties inspired by biological tissue.</a> J. Mater. Chem. B. 3, 4947-4952 (2015).</li><li>Choi, S., Lee, H., Ghaffari, R., Hyeon, T., Kim, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Recent+Advances+in+Flexible+and+Stretchable+Bio-Electronic+Devices+Integrated+with+Nanomaterials.">Recent Advances in Flexible and Stretchable Bio-Electronic Devices Integrated with Nanomaterials.</a> Adv. Mater. 28, 4203-4218 (2016).</li><li>Zhang, Z., Qiu, J., Wang, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Roll-to-roll+printing+of+flexible+thin-film+organic+thermoelectric+devices.">Roll-to-roll printing of flexible thin-film organic thermoelectric devices.</a> Manuf. Lett. 8, 6-10 (2016).</li><li>Rim, Y. S., Bae, S. -. H., Chen, H., De Marco, N., Yang, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Recent+Progress+in+Materials+and+Devices+toward+Printable+and+Flexible+Sensors.">Recent Progress in Materials and Devices toward Printable and Flexible Sensors.</a> Adv. Mater. 28, 4415-4440 (2016).</li><li>Matsuhisa, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Printable+elastic+conductors+with+a+high+conductivity+for+electronic+textile+applications.">Printable elastic conductors with a high conductivity for electronic textile applications.</a> Nat. Commun. 6, 7461 (2015).</li><li>Bernards, D. a., Malliaras, G. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Steady-State+and+Transient+Behavior+of+Organic+Electrochemical+Transistors.">Steady-State and Transient Behavior of Organic Electrochemical Transistors.</a> Adv. Funct. Mater. 17 (17), 3538-3544 (2007).</li></ol>

The authors have nothing to disclose.

전도성 재료의 패터닝 기능성 전자 소자의 제조에 첫 단계이다. 제조 공정을 고려 이러한 물질의 화학적 및 물리적 특성을 취할 필요가 있으며, 프로세스 흐름은 제조 단계의 물질 상호 호환성을 고려할 필요가 이것은 도전이 될 수있다. 유기 전자 소자의 미세 가공에서, 이들 두 측면 의한 유기물의 높은 반응성 특성 훨씬 더 중요하다. 그러나 오늘날 유기 물질은 전기 탄성 14,</s...

착용 할 수있는 전자 분야는 세 번 현재의 시장을 2025 년에 50,000,000,000유로 가치가있을 것으로 예상 빠르게 성장하는 시장이다. 현재 착용 할 수있는 장치가 직면 한 주요 과제는 방해 고체 전자 첨부 파일이 착용 할 수있는 시스템의 구축 장치의 사용을 제한 할 것입니다. 이미 일상에 존재하는 섬유를 사용하면 이러한 제한을 피하기 위해 매우 매력적이고 간단한 방법이다. 그것의 탄성 기능에, 우리가 입는 옷의 일부가 피부에 밀착 자연적이다. 시장 오늘로 볼 수 있습니다 스마트 의류의 많은 예는 세련된 방법 1 인간과 전자 제품을 연결하는 얇은 플라스틱 디스플레이, 키보드 및 섬유에 포함 된 광원 장치를 기반으로합니다. 스포츠 실제로, 상태 모니터링은 일반적으로 접착제 전극과 금속 팔찌를 사용하기 편안한 대안을 제공 섬유 전극을 사용합니다. 여기서, 도전성 섬유는직접 피부 자극과 확장 착용하는 동안 다른 불편을 방지하기 위해 신축성 직물과 통합. 또한, 섬유는 땀 4에서 분석 물의 검출을 통해 바이오 센서를 통합 확실히 작용 로봇 액추에이터 (3)의 발전 전단 센서를 통합하고, 움직임이 캡처 곡률 센서를 통합하는 기회들을 제공한다. 현대 착용 할 수있는 기술은 고유 한 특성을 가진 전자 기기를 제공하는 탄소 기반의 반도체 재료에 의존한다. 유기물의 &quot;소프트&quot;특성은 전통적인 고체 전자에 비해, 인체와의 인터페이스를 위해 더 나은 기계적 특성을 제공한다. 기계적 유연성 기재와 짝이 기계적 호환성은, 예컨대 섬유와 같은 장치에서 비평 폼 팩터의 사용을 가능하게한다. 유기물의 사용은 그들의 혼합 ELE에도 생명 과학 관련ctronic 및 이온 전도도 5. 게다가, 유기 반도체 및 광전자 재료는 디스플레이, 트랜지스터 로직, 및 전력 기능 6, 7, 8, 9와 기능 소자의 큰 다양성을 강화할. 유기 소자의 제조에있어서 가장 큰 어려움은 직물의 비평 탄 표면에 기능성 물질의 증착을 제어한다. 종래의 미세 가공 기술은 주로 섬유 기질의 구조 차원으로 증착 프로세스의 호환성에 의해 제한된다. 여기에서는 구성 섬유에 전도성 중합체의 선택적인 증착을 가능하게하는 간단하고 확장 가능한 제조 프로토콜을 설명한다. 제시된 과정은 착용 및 등각 전자 장치의 제조를 가능하게한다. 이 접근법은 (C)의 패터닝에 기초ommercially 가능한 전도성 고분자, 폴리 (3,4- 에틸렌 디옥 시티 오펜) : 폴리 (스티렌 설포 네이트) (PEDOT : PSS) 및 섬유에 탄성 스텐실 재료 폴리 디메틸 실록산 (PDMS). 뿐만 아니라 섬유의 부드럽고 신축성 특성의 유지를 위해, PSS 솔루션 :이 조합은 효율적인 수성 PEDOT의 구속 수 있습니다. 이 간단하고 신뢰성있는 제조 방법은 직접 비용 효율적이며 공업 적으로 확장 가능한 방식으로 직물에 전자 제품의 다양한 제조 방법을위한 포장한다.

<table><tbody><tr><td>SYLGARD 184, Silicone elastomer kit (Base and Curing agent)</td><td>Dow Corning</td><td></td><td>PDMS elastomer</td></tr><tr><td colspan="4">&lt;strong&gt;The conducting polymer formulation&lt;/strong&gt;</td></tr><tr><td>CleviosTM PH 1000 PEDOT:PSS</td><td>Heraeus</td><td></td><td>Conductive polymer</td></tr><tr><td>Ethylene glycol</td><td>Sigma-Aldrich</td><td>03750-250ML</td><td>Solvent (EG), CAS: 107-21-1</td></tr><tr><td>3-methacryloxypropyltrimethoxysilane</td><td>Sigma-Aldrich</td><td>M6514</td><td>Cros linker (GOPs), CAS: 2530-85-0</td></tr><tr><td>4-dodecylbenzenesulfonic acid</td><td>Sigma-Aldrich</td><td>44198</td><td>DBSA; CAS: 121-65-3</td></tr><tr><td colspan="4">&lt;strong&gt;The ionic liquid gel&lt;/strong&gt;</td></tr><tr><td>UV lamp DFE 2340</td><td>C.I.F/ ATHELEC</td><td>DP134</td><td>UV-365 nm</td></tr><tr><td>1-Ethyl-3-methylimidazolium ethyl sulfate</td><td>Sigma-Aldrich</td><td>51682-100G-F</td><td>Ionic Liquid (IL), CAS: 342573-75-5</td></tr><tr><td>Poly(ethylene glycol) diacrylate</td><td>Sigma-Aldrich</td><td>455008-100ML</td><td>Mn 700, CAS: 26570-48-9</td></tr><tr><td>2-Hydroxy-2-methylpropiophenon</td><td>Sigma-Aldrich</td><td>405655-50ML</td><td>Phot Initiator (PI), CAS: 7473-98-5</td></tr><tr><td>The textile fabric</td><td>VWR</td><td>Spec-Wipe 7 Wipers</td><td>100% interlock knit polyester fabric</td></tr><tr><td>The polyimide film</td><td>DuPont</td><td>HN100</td><td>Polyimide film with 125 &amp;micro;m thickness</td></tr></tbody></table>

a simple and scalable fabrication method for organic electronic devices on textiles

Today, wearable electronics devices combine a large variety of functional, stretchable, and flexible technologies. However, in many cases, these devices cannot be worn under everyday conditions. Therefore, textiles are commonly considered the best substrate to accommodate electronic devices in wearable use. In this paper, we describe how to selectively pattern organic electroactive materials on textiles from a solution in an easy and scalable manner. This versatile deposition technique enables the fabrication of wearable organic electronic devices on clothes.

직물에 색 또는 패턴을 적용하기위한 전통적인 방법은 염료를 선택적으로 증착 할 수 있도록 이동식 마스킹 층에 의존한다. 직물에 PSS 전극도 1에서는 PEDOT의 패터닝에 이러한 방식의 적응을 나타낸다. PSS 솔루션 : 마스킹 층으로, 우리는 수성 PEDOT의 비 제어 확산을 억제 할 수 소수성 폴리 디메틸 실록산을 사용했다. 또한, 부드러움과 니트와 짠 직물의 신축?...

Watch this Scientific Journal Video about A Simple and Scalable Fabrication Method for Organic Electronic Devices on Textiles at JoVE.com

A Simple and Scalable Fabrication Method for Organic Electronic Devices on Textiles

본 논문에서는 선택적으로 웨어러블 유기 전자 장치의 직접 통합 할 수 섬유에 유기 물질을 증착하는 프로토콜을 제시한다. 제작 된 소자는 완전히 기계적 모양을 존중하고 감지 기능을 가능하게 직물에 통합 될 수있다.

섬유에 유기 전자 장치를위한 간편하고 확장 가능한 제조 방법

Today, wearable electronics devices combine a large variety of functional, stretchable, and flexible technologies. However, in many cases, these devices ...

a-simple-scalable-fabrication-method-for-organic-electronic-devices

Research

JoVE Journal

Bioengineering

10.4K 조회수.  Ecole Nationale Supérieure des Mines de Saint-Étienne, CMP-EMSE, MOC.  본 논문에서는 선택적으로 웨어러블 유기 전자 장치의 직접 통합 할 수 섬유에 유기 물질을 증착하는 프로토콜을 제시한다. 제작 된 소자는 완전히 기계적 모양을 존중하고 감지 기능을 가능하게 직물에 통합 될 수있다. 

비디오: A Simple and Scalable Fabrication Method for Organic Electronic Devices on Textiles

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices have used devices prepared by spin coating, a process that is not amenable to large-scale fabrication. This mismatch in device fabrication makes it difficult to translate quantitative results obtained in the laboratory to the commercial level, making optimization difficult. Using a mini-slot die coater, this mismatch can be resolved by translating the commercial process to the laboratory and characterizing the structure formation in the active layer of the device in real time and in situ as films are coated onto a substrate. The evolution of the morphology was characterized under different conditions, allowing us to propose a mechanism by which the structures form and grow. This mini-slot die coater offers a simple, convenient, material efficient route by which the morphology in the active layer can be optimized under industrially relevant conditions. The goal of this protocol is to show experimental details of how a solar cell device is fabricated using a mini-slot die coater and technical details of running in situ structure characterization using the mini-slot die coater.

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Here, we present a protocol to fabricate organic thin film solar cells using a mini-slot die coater and related in-line structure characterizations using synchrotron scattering techniques.

벌크 이종 접합 태양 전지의 인쇄 제작 및<em&gt; 현장에서</em&gt; 형태학 특성

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices ...

연구

공학

Fabrication of Fully Solution Processed Inorganic Nanocrystal Photovoltaic Devices

We demonstrate a method for the preparation of fully solution processed inorganic solar cells from a spin and spray coating deposition of nanocrystal inks. For the photoactive absorber layer, colloidal CdTe and CdSe nanocrystals (3-5 nm) are synthesized using an inert hot injection technique and cleaned with precipitations to remove excess starting reagents. Similarly, gold nanocrystals (3-5 nm) are synthesized under ambient conditions and dissolved in organic solvents. In addition, precursor solutions for transparent conductive indium tin oxide (ITO) films are prepared from solutions of indium and tin salts paired with a reactive oxidizer. Layer-by-layer, these solutions are deposited onto a glass substrate following annealing (200-400 &#176;C) to build the nanocrystal solar cell (glass/ITO/CdSe/CdTe/Au). Pre-annealing ligand exchange is required for CdSe and CdTe nanocrystals where films are dipped in NH4Cl:methanol to replace long-chain native ligands with small inorganic Cl- anions. NH4Cl(s) was found to act as a catalyst for the sintering reaction (as a non-toxic alternative to the conventional CdCl2(s) treatment) leading to grain growth (136&#177;39 nm) during heating. The thickness and roughness of the prepared films are characterized with SEM and optical profilometry. FTIR is used to determine the degree of ligand exchange prior to sintering, and XRD is used to verify the crystallinity and phase of each material. UV/Vis spectra show high visible light transmission through the ITO layer and a red shift in the absorbance of the cadmium chalcogenide nanocrystals after thermal annealing. Current-voltage curves of completed devices are measured under simulated one sun illumination. Small differences in deposition techniques and reagents employed during ligand exchange have been shown to have a profound influence on the device properties. Here, we examine the effects of chemical (sintering and ligand exchange agents) and physical treatments (solution concentration, spray-pressure, annealing time and annealing temperature) on photovoltaic device performance.

This protocol describes the synthesis and solution deposition of inorganic nanocrystals layer by layer to produce thin film electronics on non-conductive surfaces. Solvent-stabilized inks can produce complete photovoltaic devices on glass substrates via spin and spray coating following post-deposition ligand exchange and sintering.

완전 해결 가공 된 무기 나노 결정 태양 광 발전 장치의 제작

We demonstrate a method for the preparation of fully solution processed inorganic solar cells from a spin and spray coating deposition of nanocrystal ...

Sensing of Barrier Tissue Disruption with an Organic Electrochemical Transistor

The gastrointestinal tract is an example of barrier tissue that provides a physical barrier against entry of pathogens and toxins, while allowing the passage of necessary ions and molecules. A breach in this barrier can be caused by a reduction in the extracellular calcium concentration. This reduction in calcium concentration causes a conformational change in proteins involved in the sealing of the barrier, leading to an increase of the paracellular flux. To mimic this effect the calcium chelator ethylene glycol-bis(beta-aminoethyl ether)-N,N,N&#39;,N&#39;-tetra acetic acid (EGTA) was used on a monolayer of cells known to be representative of the gastrointestinal tract. Different methods to detect the disruption of the barrier tissue already exist, such as immunofluorescence and&#160;permeability assays. However, these methods are time-consuming and costly and not suited to dynamic or high-throughput measurements. Electronic methods for measuring barrier tissue integrity also exist for measurement of the transepithelial resistance (TER), however these are often costly and complex. The development of rapid, cheap, and sensitive methods is urgently needed as the integrity of barrier tissue is a key parameter in drug discovery and pathogen/toxin diagnostics. The organic electrochemical transistor (OECT) integrated with barrier tissue forming cells has been shown as a new device capable of dynamically monitoring barrier tissue integrity. The device is able to measure minute variations in ionic flux with unprecedented temporal resolution and sensitivity, in real time, as an indicator of barrier tissue integrity. This new method is based on a simple device that can be compatible with high throughput screening applications and fabricated at low cost.

The Organic Electrochemical Transistor is integrated with live cells and used to monitor ion flux across the gastrointestinal epithelial barrier. In this study, an increase in ion flux, related to disruption of tight junctions, induced by the presence of the calcium chelator EGTA (ethylene glycol-bis(beta-aminoethyl ether)-N,N,N',N'-tetra acetic acid), is measured.

유기 전기 트랜지스터와 장벽 조직 혼란의 감지

The gastrointestinal tract is an example of barrier tissue that provides a physical barrier against entry of pathogens and toxins, while allowing the ...

생체공학

Scalable Solution-processed Fabrication Strategy for High-performance, Flexible, Transparent Electrodes with Embedded Metal Mesh

Here, the authors report the embedded metal-mesh transparent electrode (EMTE), a new transparent electrode (TE) with a metal mesh completely embedded in a polymer film. This paper also presents a low-cost, vacuum-free fabrication method for this novel TE; the approach combines lithography, electroplating, and imprint transfer (LEIT) processing. The embedded nature of the EMTEs offers many advantages, such as high surface smoothness, which is essential for organic electronic device production; superior mechanical stability during bending; favorable resistance to chemicals and moisture; and strong adhesion with plastic film. LEIT fabrication features an electroplating process for vacuum-free metal deposition and is favorable for industrial mass production. Furthermore, LEIT allows for the fabrication of metal mesh with a high aspect ratio (i.e., thickness to linewidth), significantly enhancing its electrical conductance without adversely losing optical transmittance. We demonstrate several prototypes of flexible EMTEs, with sheet resistances lower than 1 &#937;/sq and transmittances greater than 90%, resulting in very high figures of merit (FoM) &#8211; up to 1.5 x 104 &#8211; which are amongst the best values in the published literature.

This protocol describes a solution-based fabrication strategy for high-performance, flexible, transparent electrodes with fully-embedded, thick metal mesh. Flexible transparent electrodes fabricated by this process demonstrate among the highest reported performances, including ultra-low sheet resistance, high optical transmittance, mechanical stability under bending, strong substrate adhesion, surface smoothness, and environmental stability.

Here, the authors report the embedded metal-mesh transparent electrode (EMTE), a new transparent electrode (TE) with a metal mesh completely embedded in a ...

Reactive Vapor Deposition of Conjugated Polymer Films on Arbitrary Substrates

We demonstrate a method of conformally coating conjugated polymers on arbitrary substrates using a custom-designed, low-pressure reaction chamber. Conductive polymers, poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3,4-propylenedioxythiophene) (PProDOT), and a semiconducting polymer, poly(thieno[3,2-b]thiophene) (PTT), were deposited on unconventional highly-disordered and textured substrates with high surface areas, such as paper, towels and fabrics. This reported deposition chamber is an improvement of previous vapor reactors because our system can accommodate both volatile and nonvolatile monomers, such as 3,4-propylenedioxythiophene and thieno[3,2-b]thiophene. Utilization of both solid and liquid oxidants are also demonstrated. One limitation of this method is that it lacks sophisticated in situ thickness monitors. Polymer coatings made by the commonly used solution-based coating methods, such as spin-coating and surface grafting, are often not uniform or susceptible to mechanical degradation. This reported vapor phase deposition method overcomes those drawbacks and is a strong alternative to common solution-based coating methods. Notably, polymer films coated by the reported method are uniform and conformal on rough surfaces, even at a micrometer scale. This feature allows for future application of vapor deposited polymers in electronics devices on flexible and highly textured substrates.

This paper presents a protocol for reactive vapor deposition of poly(3,4-ethylenedioxythiophene), poly(3,4-propylenedioxythiophene), and poly(thieno[3,2-b]thiophene) films on glass slides and rough substrates, such as textiles and paper.

임의 기판에 활용 된 고분자 필름의 반응성 증 착

We demonstrate a method of conformally coating conjugated polymers on arbitrary substrates using a custom-designed, low-pressure reaction chamber. ...

화학

Fabrication of Flexible Image Sensor Based on Lateral NIPIN Phototransistors

Flexible photodetectors have been intensely studied for the use of curved image sensors, which are a crucial component in bio-inspired imaging systems, but several challenging points remain, such as a low absorption efficiency due to a thin active layer and low flexibility. We present an advanced method to fabricate a flexible phototransistor array with an improved electrical performance. The outstanding electrical performance is driven by a low dark current owing to deep impurity doping. Stretchable and flexible metal interconnectors simultaneously offer electrical and mechanical stabilities in a highly deformed state. The protocol explicitly describes the fabrication process of the phototransistor using a thin silicon membrane. By measuring I-V characteristics of the completed device in deformed states, we demonstrate that this approach improves the mechanical and electrical stabilities of the phototransistor array. We expect that this approach to a flexible phototransistor can be widely used for the applications of not only next-generation imaging systems/optoelectronics but also wearable devices such as tactile/pressure/temperature sensors and health monitors.

We present a detailed method to fabricate a deformable lateral NIPIN phototransistor array for curved image sensors. The phototransistor array with an open mesh form, which is composed of thin silicon islands and stretchable metal interconnectors, provides flexibility and stretchability. The parameter analyzer characterizes the electrical property of the fabricated phototransistor.

측면 NIPIN 포토 트랜지스터에 따라 유연한 이미지 센서의 제조

Flexible photodetectors have been intensely studied for the use of curved image sensors, which are a crucial component in bio-inspired imaging systems, ...

Fabrication and Characterization of a Conformal Skin-like Electronic System for Quantitative, Cutaneous Wound Management

Recent advances in the development of electronic technologies and biomedical devices offer opportunities for non-invasive, quantitative assessment of cutaneous wound healing on the skin. Existing methods, however, still rely on visual inspections through various microscopic tools and devices that normally include high-cost, sophisticated systems and require well trained personnel for operation and data analysis. Here, we describe methods and protocols to fabricate a conformal, skin-like electronics system that enables conformal lamination to the skin surface near the wound tissues, which provides recording of high fidelity electrical signals such as skin temperature and thermal conductivity. The methods of device fabrication provide details of step-by-step preparation of the microelectronic system that is completely enclosed with elastomeric silicone materials to offer electrical isolation. The experimental study presents multifunctional, biocompatible, waterproof, reusable, and flexible/stretchable characteristics of the device for clinical applications. Protocols of clinical testing provide an overview and sequential process of cleaning, testing setup, system operation, and data acquisition with the skin-like electronics, gently mounted on hypersensitive, cutaneous wound and contralateral tissues on patients.

This article presents methods to fabricate and characterize a conformal, skin-like electronic system and protocols for the use in clinical applications, particularly on cutaneous wound management.

양적, 피부가 상처 관리를위한 등각 피부와 같은 전자 시스템의 제조 및 특성

Recent advances in the development of electronic technologies and biomedical devices offer opportunities for non-invasive, quantitative assessment of ...

Hybrid Printing for the Fabrication of Smart Sensors

A method to combine additively manufactured substrates or foils and multilayer inkjet printing for the fabrication of sensor devices is presented. First, three substrates (acrylate, ceramics, and copper) are prepared. To determine the resulting material properties of these substrates, profilometer, contact angle, scanning electron microscope (SEM), and focused ion beam (FIB) measurements are done. The achievable printing resolution and suitable drop volume for each substrate are, then, found through the drop size tests. Then, layers of insulating and conductive ink are inkjet printed alternately to fabricate the target sensor structures. After each printing step, the respective layers are individually treated by photonic curing. The parameters used for the curing of each layer are adapted depending on the printed ink, as well as on the surface properties of the respective substrate. To confirm the resulting conductivity and to determine the quality of the printed surface, four-point probe and profilometer measurements are done. Finally, a measurement set-up and results achieved by such an all-printed sensor system are shown to demonstrate the achievable quality.

Here we present a protocol for the fabrication of inkjet-printed multilayer sensor structures on additively manufactured substrates and foil.

스마트 센서의 제조에 인쇄 하는 하이브리드

A method to combine additively manufactured substrates or foils and multilayer inkjet printing for the fabrication of sensor devices is presented. First, ...

Development of Efficient OLEDs from Solution Deposition

The use of highly efficient organic emitters based on the thermally activated delayed fluorescence (TADF) concept is interesting due to their 100% internal quantum efficiency. Presented here is a solution deposition method for the fabrication of efficient organic light-emitting diodes (OLEDs) based on a TADF emitter in a simple device structure. This fast, low-cost, and efficient process can be used for all OLED emissive layers that follow the host-guest concept. The fundamental steps are described along with necessary information for further reproduction. The goal to establish a general protocol that can be easily adapted for principal organic emitters currently under study and development.

Presented here is a protocol for the fabrication of efficient, simple, solution-deposited organic light-emitting diodes with low roll-off.

용액 증착을 통한 효율적인 OLED 개발

The use of highly efficient organic emitters based on the thermally activated delayed fluorescence (TADF) concept is interesting due to their 100% ...

Fabrication of Fine Electrodes on the Tip of Hypodermic Needle Using Photoresist Spray Coating and Flexible Photomask for Biomedical Applications

We have introduced a fabrication method for electrical impedance spectroscopy (EIS)-on-a-needle (EoN: EIS-on-a-needle) to locate target tissues in the body by measuring and analyzing differences in the electrical impedance between dissimilar biotissues. This paper describes the fabrication method of fine interdigitated electrodes (IDEs) at the tip of a hypodermic needle using a photoresist spray coating and flexible film photomask in the photolithography process. A polyethylene terephthalate (PET) heat shrink tube (HST) with a wall thickness of 25 &#181;m is employed as the insulation and passivation layer. The PET HST shows a higher mechanical durability compared with poly(p-xylylene) polymers, which have been widely used as a dielectric coating material. Furthermore, the HST shows good chemical resistance to most acids and bases, which is advantageous for limiting chemical damage to the EoN. The use of the EoN is especially preferred for the characterization of chemicals/biomaterials or fabrication using acidic/basic chemicals. The fabricated gap and width of the IDEs are as small as 20 &#181;m, and the overall width and length of the IDEs are 400 &#181;m and 860 &#181;m, respectively. The fabrication margin from the tip (distance between the tip of hypodermic needle and starting point of the IDEs) of the hypodermic needle is as small as 680 &#181;m, which indicates that unnecessarily excessive invasion into biotissues can be avoided during the electrical impedance measurement. The EoN has a high potential for clinical use, such as for thyroid biopsies and anesthesia drug delivery in a spinal space. Further, even in surgery that involves the partial resection of tumors, the EoN can be employed to preserve as much normal tissue as possible by detecting the surgical margin (normal tissue that is removed with the surgical excision of a tumor) between the normal and lesion tissues.

The fabrication method for fine interdigitated electrodes (gap and width: 20 &#181;m) at the tip of a hypodermic needle (diameter: 720 &#181;m) is demonstrated using a spray coating and flexible film photomask in the photolithography process.

생명 의학 어플리케이션에 대 한 포토 레지스트 스프레이 코팅 및 유연한 포토 마스크를 사용 하 여 피하 주사 바늘 끝에 미세 전극의 제조

We have introduced a fabrication method for electrical impedance spectroscopy (EIS)-on-a-needle (EoN: EIS-on-a-needle) to locate target tissues in the ...