The review of catalyst applications was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Biosciences, and Geosciences Catalysis Program under contract DE-AC05-RL01830 and FWP-47319. The review of biomedical applications was supported by the National Institute of Health, National Institute of Environmental Health Sciences under grant R21ES029778. Experiments were conducted at EMSL (grid.436923.9), a DOE Office of Science User Facility sponsored by the Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory (PNNL). PNNL is a multi-program national laboratory operated by Battelle for the U.S. Department of Energy under contract DE-AC05-RL01830 and FWP-47319.

The protocol is divided into four sections which specify 1) the preparation of any solid materials being used in the system or activation or clearing of undesired adsorbed species, 2) addition of the solid and liquid materials to the NMR rotor, 3) addition of gases to the rotor, and 4) conducting the NMR experiments in the spectrometer. The procedure is representative of a typical sequence but may be modified to fit the specific needs of the experiment.
1. Pretreating solid samples
<ol>
	<li>Weigh approximately twice the mass of the solid sample that is desired for the NMR experiment (for a 7.5 mm rotor, ~250 mg) and place the solid sample into a quartz sample tube used for treating materials in a furnace system, plugging the tube with quartz wool to hold the material in place.</li>
	<li>Connect the isolation valves to the solids treatment 1) flow or 2) vacuum system by placing the tube into the cool furnace and tightening the connections.</li>
	<li>Affix the quartz tube end(s) onto the gas isolation valve(s) in the open position.</li>
	<li>Begin the treatment.
	<ol>
		<li>For flow systems:
		<ol>
			<li>Affix a thermocouple to the outside of the tube, holding it in place with a heat-resistant material.</li>
			<li>Begin the flow of the treatment gas (e.g., N2 at 100 sccm) to clear the solid surface or activate the material.</li>
		</ol>
		</li>
		<li>Alternatively, for vacuum systems:
		<ol>
			<li>Close the isolation valve to the vacuum system and start the vacuum pump.</li>
			<li>When full vacuum is established, very slowly open the isolation valve to apply vacuum to the sample, pausing periodically to allow the system to equilibrate. Continue until the valve is open.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Turn on the furnace controller and set the temperature ramp program to the desired condition (e.g., 300 &#176;C for 4 hours at a ramp rate of 5 &#176;C/min).</li>
	<li>Start the temperature program and let it run.</li>
	<li>When completed, allow the sample to cool to a workable temperature.</li>
	<li>Turn off the temperature controller and stop the flow/vacuum.</li>
	<li>Quickly seal the sample with the isolation valves to maintain the desired sample environment.</li>
	<li>Disconnect the quartz tube from the treatment system and transfer the tubes and closed valves to the antechamber of a dry, N2-purged glove box.</li>
	<li>Empty and refill the antechamber at least 4 times and transfer the tube inside of the glove box.</li>
</ol>
2. Loading solid samples into the NMR rotor
<ol>
	<li>Weigh the empty and clean high-pressure, high-temperature NMR rotor with the rotor cap.</li>
	<li>Place the NMR rotor in the holder to maintain directionality.</li>
	<li>Place the sample funnel into the bore of the rotor.</li>
	<li>Remove the isolation valve(s) from the sample tube and pour a small quantity of solid material into the funnel.</li>
	<li>Tap the powder down into the funnel and lightly direct it into the rotor with the packing rod as necessary.</li>
	<li>Repeat the stepwise addition of solid material until the desired quantity (e.g., &#189; rotor) is achieved.</li>
	<li>Weigh the NMR rotor (and cap) with the sample inside to determine the quantity of sample added.</li>
	<li>If desired, draw up a specified quantity of any liquid sample and slowly inject the liquid into the center of the NMR rotor with a micro syringe.</li>
	<li>Seal the rotor by placing the cap onto the top and turning it counterclockwise with the rotor cap bit to engage the O-ring between the rotor and cap. Note that a new O-ring may be&#160;periodically required to prevent leaking, especially if using chemically abrasive mixtures or small gases such as hydrogen.</li>
	<li>Weigh the NMR rotor to determine the total mass of added sample.</li>
</ol>
3. Charging the NMR rotor with the desired chemicals at the desired conditions
<ol>
	<li>Place the sealed NMR rotor into the rotor stage, ensuring the size of the stage insert is compatible with the rotor size, and tighten the nut by hand to secure it in place. Note that the tightness of the rotor in the holder in this step will determine the tightness of the cap seal.</li>
	<li>Lower the rotor stage into the lower section of the high-pressure exposure device.</li>
	<li>Use an Allen wrench to turn one of the screws 90&#176; to secure the rotor stage into the bottom of the exposure device.</li>
	<li>Place the top section of the NMR loading device into and on top of the bottom section, lining up the NMR cap bit to the top of the cap head of the NMR rotor to ensure it is engaged.</li>
	<li>Place the 2 clamps over the top of the lip where the upper and lower sections of the exposure device meet and latch them in place.</li>
	<li>Tighten the 6 bolts on the top of the upper section of the exposure device to engage the sealing surface between the upper and lower sections.</li>
	<li>Connect the upper section of the NMR exposure device to the gas line inlet and outlets.</li>
	<li>Connect the thermocouple on the upper section of the NMR exposure device to the temperature sensor.</li>
	<li>If desired, wrap the heating tape around the gas lines and upper sections of the exposure device to enable heating with the respective controller. A hot plate can also be engaged.</li>
	<li>Ensuring the exposure chamber outlet is open and source gas valve is closed, turn on the vacuum pump to remove air from the exposure device and associated lines.</li>
	<li>Purge the lines with either the desired gas or an inert one, cycling between vacuum and atmospheric pressure three times to ensure the lines are cleared of air.</li>
	<li>Prepare the desired gas composition either from 1) a high-pressure delivery system or 2) a flow system to introduce vapors at a specified pressure.
	<ol>
		<li>For high-pressure or vacuum sample preparation:
		<ol>
			<li>Close the exposure device gas outlet and set the gas manifold valves to bypass the liquid injection line.</li>
			<li>Set the desired pressure on the high-pressure syringe pump of the high-pressure delivery system.</li>
			<li>Open the gas source valves on the high-pressure syringe pump and run the program set on the pump, monitoring the real pressure inside of the exposure device.</li>
			<li>When the desired pressure is achieved inside the exposure device, stop the syringe pump and close the source gas valves.</li>
			<li>Open the NMR rotor by rotating clockwise the external screw mechanism, which is coupled to the interior NMR cap bit.</li>
			<li>Allow the gas of the desired pressure to enter the NMR rotor and equilibrate.</li>
			<li>Reseal the NMR rotor by rotating the external screw mechanism counterclockwise. A viewing window will assist in determining when the rotor is closed.</li>
			<li>Slowly depressurize the system by opening the exposure device gas outlet valve.</li>
		</ol>
		</li>
		<li>For flowing gas or vapor sample preparation:
		<ol>
			<li>Ensure the exposure device gas outlet is open to prevent over-pressure.</li>
			<li>Set the desired gas flow rate on the mass flow controller and begin the gas flow.</li>
			<li>Connect the liquid supply line from the liquid syringe pump to the gas manifold.</li>
			<li>Set the gas manifold valves to enable flow to the liquid injection line.</li>
			<li>Set the liquid flow rate on the liquid syringe pump to achieve the desired vapor pressure and begin liquid injection.</li>
			<li>Open the NMR rotor by rotating clockwise the external screw mechanism which is coupled to the interior NMR cap bit.</li>
			<li>Allow the system to equilibrate to the desired gas pressures inside the NMR rotor and reseal the NMR rotor by rotating the external screw mechanism counterclockwise. A viewing window will assist in determining when the rotor is closed.</li>
			<li>Stop the liquid syringe pump injection and configure the valves to bypass the liquid injection line, disconnecting the pump from the system.</li>
			<li>Stop the flowing gas.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Purge the system with an inert gas to remove any potentially toxic or flammable gases.</li>
	<li>Stop any heating and allow the system to cool.</li>
	<li>Disconnect any heating tape and the thermocouple.</li>
	<li>Disconnect the inlet and outlet gas lines.</li>
	<li>Loosen the 6 bolts on the top of the exposure device to compromise the seal.</li>
	<li>Unclip the 2 clamping sections and remove them from the exposure device.</li>
	<li>Carefully lift the upper section up and off the lower section.</li>
	<li>Use an Allen wrench to loosen the rotor stage and draw it up with the threaded rod.</li>
	<li>Loosen the nut on the rotor stage and remove the rotor from the device component.</li>
	<li>Weigh the rotor to ensure the desired gas quantities are present.</li>
</ol>
4. Conducting the MAS NMR experiment
<ol>
	<li>Place the NMR rotor into the NMR coil on the NMR probe.</li>
	<li>Raise the probe into the magnet bore and lock it into place.</li>
	<li>Initiate sample spinning using the MAS control box and adjust to the desired rotor spinning rate.</li>
	<li>Use the computer to begin the tuning/match sequence on the desired channel.</li>
	<li>Adjust the tuning/match settings on the probe to optimize the probe electronics.</li>
	<li>Exit the tuning/match sequence on the computer and set up the desired experimental parameters (e.g., pulse sequence, experiment array, temperature, etc.).</li>
	<li>Collect the MAS NMR data.</li>
</ol>

<ol>
	<li>Andrew, E. R., Bradbury, A., Eades, R. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nuclear+Magnetic+Resonance+Spectra+from+a+Crystal+rotated+at+High+Speed.">Nuclear Magnetic Resonance Spectra from a Crystal rotated at High Speed.</a> Nature. 182 (4650), 1659 (1958).</li><li>Lowe, I. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Free+Induction+Decays+of+Rotating+Solids.">Free Induction Decays of Rotating Solids.</a> Physical Review Letters. 2 (7), 285-287 (1959).</li><li>Frydman, L., Grant, D. M., Harris, R. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fundamentals+of+Multiple-Quantum+Magic-Angle+Spinning+NMR+on+Half-Integer+Quadrupolar+Nuclei.">Fundamentals of Multiple-Quantum Magic-Angle Spinning NMR on Half-Integer Quadrupolar Nuclei.</a> Encyclopedia of Nuclear Magnetic Resonance. 9, 262-274 (2002).</li><li>Khodov, I., Dyshin, A., Efimov, S., Ivlev, D., Kiselev, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-pressure+NMR+spectroscopy+in+studies+of+the+conformational+composition+of+small+molecules+in+supercritical+carbon+dioxide.">High-pressure NMR spectroscopy in studies of the conformational composition of small molecules in supercritical carbon dioxide.</a> Journal of Molecular Liquids. 309, (2020).</li><li>Kolbe, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-Pressure+in+situ+129Xe+NMR+Spectroscopy:+Insights+into+Switching+Mechanisms+of+Flexible+Metal-Organic+Frameworks+Isoreticular+to+DUT-49.">High-Pressure in situ 129Xe NMR Spectroscopy: Insights into Switching Mechanisms of Flexible Metal-Organic Frameworks Isoreticular to DUT-49.</a> Chemistry of Materials. 31 (16), 6193-6201 (2019).</li><li>Ochoa, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=(2)+H+and+(139)+La+NMR+Spectroscopy+in+Aqueous+Solutions+at+Geochemical+Pressures.">(2) H and (139) La NMR Spectroscopy in Aqueous Solutions at Geochemical Pressures.</a> Angewandte Chemie International Edition. 54 (51), 15444-15447 (2015).</li><li>Hoffmann, H. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-pressure+in+situ+129Xe+NMR+spectroscopy+and+computer+simulations+of+breathing+transitions+in+the+metal-organic+framework+Ni2(2,6-ndc)2(dabco)+(DUT-8(Ni)).">High-pressure in situ 129Xe NMR spectroscopy and computer simulations of breathing transitions in the metal-organic framework Ni2(2,6-ndc)2(dabco) (DUT-8(Ni)).</a> Journal of the American Chemical Society. 133 (22), 8681-8690 (2011).</li><li>Turcu, R. V. F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rotor+design+for+high+pressure+magic+angle+spinning+nuclear+magnetic+resonance.">Rotor design for high pressure magic angle spinning nuclear magnetic resonance.</a> Journal of Magnetic Resonance. 226, 64-69 (2013).</li><li>Jaegers, N. R., Hu, M. Y., Hoyt, D. W., Wang, Y., Hu, J. Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+and+Application+of+In+situ+High-Temperature,+High-Pressure+Magic+Angle+Spinning+NMR.">Development and Application of In situ High-Temperature, High-Pressure Magic Angle Spinning NMR.</a> Modern Magnetic Resonance. , 1-19 (2017).</li><li>Miyoshi, T., Takegoshi, K., Terao, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=13C+High-Pressure+CPMAS+NMR+Characterization+of+the+Molecular+Motion+of+Polystyrene+Plasticized+by+CO2+Gas.">13C High-Pressure CPMAS NMR Characterization of the Molecular Motion of Polystyrene Plasticized by CO2 Gas.</a> Macromolecules. 30 (21), 6582-6585 (1997).</li><li>Miyoshi, T., Takegoshi, K., Terao, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=129Xe+n.m.r.+study+of+free+volume+and+phase+separation+of+the+polystyrene/poly(vinyl+methyl+ether)+blend.">129Xe n.m.r. study of free volume and phase separation of the polystyrene/poly(vinyl methyl ether) blend.</a> Polymer. 38 (21), 5475-5480 (1997).</li><li>Miyoshi, T., Takegoshi, K., Terao, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+Xe+Gas+on+Segmental+Motion+in+a+Polymer+Blend+As+Studied+by+13C+and+129Xe+High-Pressure+MAS+NMR.">Effects of Xe Gas on Segmental Motion in a Polymer Blend As Studied by 13C and 129Xe High-Pressure MAS NMR.</a> Macromolecules. 35 (1), 151-154 (2002).</li><li>Yonker, C. R., Linehan, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+use+of+supercritical+fluids+as+solvents+for+NMR+spectroscopy.">The use of supercritical fluids as solvents for NMR spectroscopy.</a> Progress in Nuclear Magnetic Resonance Spectroscopy. 47 (1), 95-109 (2005).</li><li>Deuchande, T., Breton, O., Haedelt, J., Hughes, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+performance+of+a+high+pressure+insert+for+use+in+a+standard+magic+angle+spinning+NMR+probe.">Design and performance of a high pressure insert for use in a standard magic angle spinning NMR probe.</a> Journal of Magnetic Resonance. 183 (2), 178-182 (2006).</li><li>Hoyt, D. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-pressure+magic+angle+spinning+nuclear+magnetic+resonance.">High-pressure magic angle spinning nuclear magnetic resonance.</a> Journal of Magnetic Resonance. 212 (2), 378-385 (2011).</li><li>Vjunov, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Following+Solid-Acid-Catalyzed+Reactions+by+MAS+NMR+Spectroscopy+in+Liquid+Phase-Zeolite-Catalyzed+Conversion+of+Cyclohexanol+in+Water.">Following Solid-Acid-Catalyzed Reactions by MAS NMR Spectroscopy in Liquid Phase-Zeolite-Catalyzed Conversion of Cyclohexanol in Water.</a> Angewandte Chemie International Edition. 53 (2), 479-482 (2014).</li><li>Chamas, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High+temperature/pressure+MAS-NMR+for+the+study+of+dynamic+processes+in+mixed+phase+systems.">High temperature/pressure MAS-NMR for the study of dynamic processes in mixed phase systems.</a> Magnetic Resonance Imaging. 56, 37-44 (2019).</li><li>Hu, J. Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sealed+rotors+for+in+situ+high+temperature+high+pressure+MAS+NMR.">Sealed rotors for in situ high temperature high pressure MAS NMR.</a> ChemComm. 51 (70), 13458-13461 (2015).</li><li>Hu, J. Z., Hu, M. Y., Townsend, M. R., Lercher, J. A., Peden, C. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-pressure,+high-temperature+magic+angle+spinning+nuclear+magnetic+resonance+devices+and+processes+for+making+and+using+same.">High-pressure, high-temperature magic angle spinning nuclear magnetic resonance devices and processes for making and using same.</a> US patent. , (2015).</li><li>Jaegers, N. R., Mueller, K. T., Wang, Y., Hu, J. Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Variable+Temperature+and+Pressure+Operando+MAS+NMR+for+Catalysis+Science+and+Related+Materials.">Variable Temperature and Pressure Operando MAS NMR for Catalysis Science and Related Materials.</a> Accounts of Chemical Research. 53 (3), 611-619 (2020).</li><li>Dagle, V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Single-step+Conversion+of+Ethanol+to+n-butenes+over+Ag-ZrO2/SiO2+catalysts.">Single-step Conversion of Ethanol to n-butenes over Ag-ZrO2/SiO2 catalysts.</a> ACS Catalysis. 10 (18), 10602-10613 (2020).</li><li>Jaegers, N. R., Wang, Y., Hu, J. Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Thermal+perturbation+of+NMR+properties+in+small+polar+and+non-polar+molecules.">Thermal perturbation of NMR properties in small polar and non-polar molecules.</a> Scientific Reports UK. 10 (1), 6097 (2020).</li><li>Jaegers, N. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Applications of In situ Magnetic Resonance Spectroscopy for Structural Analysis of Oxide-supported Catalysts. , (2019).</li><li>Mehta, H. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+novel+high-temperature+MAS+probe+with+optimized+temperature+gradient+across+sample+rotor+for+in-situ+monitoring+of+high-temperature+high-pressure+chemical+reactions.">A novel high-temperature MAS probe with optimized temperature gradient across sample rotor for in-situ monitoring of high-temperature high-pressure chemical reactions.</a> Solid State Nuclear Magnetic Resonance. 102, 31-35 (2019).</li><li>Hu, J. Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+large+sample+volume+magic+angle+spinning+nuclear+magnetic+resonance+probe+for+in+situ+investigations+with+constant+flow+of+reactants.">A large sample volume magic angle spinning nuclear magnetic resonance probe for in situ investigations with constant flow of reactants.</a> Physical Chemistry Chemical Physics. 14 (7), 2137-2143 (2012).</li><li>Jiang, Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+situ+MAS+NMR-UV/Vis+investigation+of+H-SAPO-34+catalysts+partially+coked+in+the+methanol-to-olefin+conversion+under+continuous-flow+conditions+and+of+their+regeneration.">In situ MAS NMR-UV/Vis investigation of H-SAPO-34 catalysts partially coked in the methanol-to-olefin conversion under continuous-flow conditions and of their regeneration.</a> Microporous and Mesoporous Materials. 105 (1-2), 132-139 (2007).</li><li>Xu, S., Zhang, W., Liu, X., Han, X., Bao, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Enhanced+In+situ+Continuous-Flow+MAS+NMR+for+Reaction+Kinetics+in+the+Nanocages.">Enhanced In situ Continuous-Flow MAS NMR for Reaction Kinetics in the Nanocages.</a> Journal of the American Chemical Society. 131 (38), 13722-13727 (2009).</li><li>Graham, T. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+situ+Al-27+NMR+Spectroscopy+of+Aluminate+in+Sodium+Hydroxide+Solutions+above+and+below+Saturation+with+Respect+to+Gibbsite.">In situ Al-27 NMR Spectroscopy of Aluminate in Sodium Hydroxide Solutions above and below Saturation with Respect to Gibbsite.</a> Inorganic Chemistry. 57 (19), 11864-11873 (2018).</li><li>Zhang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Boehmite+and+Gibbsite+Nanoplates+for+the+Synthesis+of+Advanced+Alumina+Products.">Boehmite and Gibbsite Nanoplates for the Synthesis of Advanced Alumina Products.</a> ACS Applied Nano Materials. 1 (12), 7115-7128 (2018).</li><li>Zhang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transformation+of+Gibbsite+to+Boehmite+in+Caustic+Aqueous+Solution+at+Hydrothermal+Conditions.">Transformation of Gibbsite to Boehmite in Caustic Aqueous Solution at Hydrothermal Conditions.</a> Crystal Growth &amp; Design. 19 (10), 5557-5567 (2019).</li><li>Hu, J. Z., Jaegers, N. R., Hu, M. Y., Mueller, K. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+situ+and+ex+situ+NMR+for+battery+research.">In situ and ex situ NMR for battery research.</a> Journal of Physics: Condensed Matter. 30 (46), (2018).</li><li>Hu, J. Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adsorption+and+Thermal+Decomposition+of+Electrolytes+on+Nanometer+Magnesium+Oxide:+An+in+situ+C-13+MAS+NMR+Study.">Adsorption and Thermal Decomposition of Electrolytes on Nanometer Magnesium Oxide: An in situ C-13 MAS NMR Study.</a> ACS Applied Materials &amp; Interfaces. 11 (42), 38689-38696 (2019).</li></ol>

The authors declare the following competing financial interests. J.Z.H and colleagues hold a patent on the rotor design (US9151813B2). J.Z.H., N.R.J., et al. have filed a provisional patent application on the exposure device.

The method of conducting MAS NMR spectroscopic measurements outlined herein represents the state of the art for conducting high-temperature, high-pressure MAS NMR. Such methods enable the observation of interactions occurring in vacuum atmospheres up to several hundred bar and from low temperatures (well below 0 &#176;C to 250 &#176;C) in a reliable, reproducible fashion. The ability to probe systems containing mixtures of solids, liquids, and gases under flexible chemical environments enables a wide range of experiments...

Spectroscopic analysis of samples is an analytical tool used to gain valuable information about materials of interest such as their chemical state, structure, or reactivity. In a simplistic view, nuclear magnetic resonance (NMR) is one such technique that utilizes a strong magnetic field to manipulate the spin state of atomic nuclei to better understand the chemical environment of the species of interest. The nuclear spin state refers to the relative direction of the magnetic moment induced by the motion of the spinning nucleus, a positively charged particle. In the absence of a magnetic field, the nuclear spins are randomly oriented but in the presence of a magnetic field, nuclear spins preferentially align with the external field of the magnet in a low energy spin state. This splitting of spin states to discrete energy values is known as the Zeeman effect. The difference between these energy levels (&#916;E) is modeled by Equation 1: 
<img alt="Equation 1" src="/files/ftp_upload/61794/61794equ01.jpg" /> 
where h is Plank&#8217;s constant, B0 is the strength of the external magnetic field and &#947; is the gyromagnetic ratio of the nucleus. The chemical environment of these spins also applies slight perturbations to these energy levels. Radio waves of corresponding frequencies can be used to excite the nuclei, which generates a transverse magnetization due to spins gaining phase coherence as longitudinal magnetization (based on the population of spins in parallel and anti-parallel states) is decreased. As the nuclei continue precessing about the axis of the magnetic field, the rotating magnetic movement creates a magnetic field that is also rotating and generating an electric field. This field modulates the electrons in the NMR detection coil, generating the NMR signal. Slight differences in the chemical environment of the nuclei in the sample affect the frequencies detected in the coil.
NMR analysis of solid samples introduces complexities not found in fluids. In fluids, the molecules tumble at fast rates, averaging the chemical environment spatially around the nuclei. In solid samples, no such averaging effect occurs, introducing an orientation-dependent chemical environment and broad spectral lines in the NMR signal. To mitigate these challenges, a technique known as magic angle spinning (MAS) is employed1,2. In MAS NMR, the samples are quickly rotated (several kilohertz) at an angle of 54.7356&#176; with respect to the external magnetic field using an external spinning mechanism to address the orientation-dependent (anisotropic) interactions of NMR. This substantially narrows the NMR features and enhances the spectral resolution by averaging the orientation-dependent terms of the chemical shift anisotropy, dipolar interactions, and quadrupolar interactions. Two notable exceptions do hinder the line narrowing abilities of MAS NMR. The first is strong homonuclear coupling sometimes present in 1H NMR that requires high spinning speeds (~70 kHz) to remove. However, the significantly elevated temperatures of the high temperature applications will greatly suppress the 1H homonuclear interaction by imparting enhanced thermal motion such that a much reduced sample spinning rate can be utilized for significantly enhanced spectral resolution. Furthermore, with the technology continuously evolving, rotors with smaller diameters can now be fabricated to achieve spinning rates far exceeding 5 kHz, which helps to further suppress the 1H homonuclear dipolar interactions. The second exception is residual second-order quadrupolar interactions for nuclei with spin that exceeds one-half since only the first order term is eliminated at the magic angle, leaving more complex lineshapes that can only be improved by stronger external magnetic fields. It should be emphasized that 2D MQMAS techniques can be readily incorporated into the current technology so that a true isotropic chemical shift spectrum can be obtained in a similar way as to the standard MQMAS experiments3.
MAS NMR has enabled detailed characterization of solid materials, strengthening the quality of observations. However, the necessity of spinning the samples in NMR rotors (the sample holder) at high rates also imposes challenges in conducting experiments at elevated temperatures and pressures which may be more relevant to the conditions of interest. It may, at times, be desirable to examine materials under conditions that are relatively harsh for NMR rotors. A number of efforts have successfully adapted liquid-state NMR technologies to conduct high-temperature, high-pressure NMR4,5,6,7; however, commercial rotor caps used for solid-state MAS NMR may be expelled from the rotor at high pressures, causing significant damage to the equipment. Such effects may be compounded by examining a decomposition reaction that greatly increases the pressure in the sample holder. As such, new designs are required to effectively and safely conduct in situ NMR experiments. For example, the rotor must adhere to several qualities for effective use in MAS NMR, namely non-magnetic, lightweight, durable, temperature resistant, low NMR background material, sealable, high-strength, and chemical resistant. The pressures the rotor must withstand are quite large. Not only must the rotor withstand the pressure of the sample contained within (e.g., high-pressure gas), the rotation of the device imparts centrifugal force which has its own contribution to the total system pressure8, PT, by equation 2: 
<img alt="Equation 2" src="/files/ftp_upload/61794/61794equ02.jpg" /> 
RI and RO are the inner and outer rotor radii, respectively, &#969; is the rotational frequency in radians per second, and Ps is the sample pressure.
A number of strategies have been developed to address these concerns9. Early examples resembled flame-sealed tubes10,11,12 or polymer inserts13,14, which were insufficient for extended, fine-controlled operation at elevated temperatures and pressures. Iterations to rotor designs have suffered from limitations in the maximum operating temperature imparted by the use of epoxy or sample volume reductions from ceramic inserts8,15,16. A recent technology reduces unit production costs by employing simple snap-in features in a commercial rotor sleeve, but offers relatively less control over the conditions with which it can operate17. The design employed herein is an all-zirconia, cavern-style rotor sleeve milled with a threaded top18. A cap is also threaded to allow for a secure seal. Reverse threading prevents sample rotation from loosening the zirconia cap and an O-ring constitutes the sealing surfaces. This rotor design is visible in Figure 1 and similar rotors and instructions to make them have been patented19. Such a strategy enables high mechanical strength, chemical resistance, and temperature tolerance.
These designs are suitable for temperatures and pressures of at least 250 &#176;C and 100 bar, limited in temperature by readily-available NMR probe technology. When combined with specialized sample preparation equipment, it represents a truly powerful technique that has been employed for far-reaching applications as carbon sequestration, catalysis, energy storage, and biomedicine20. Such equipment includes a way to pretreat the solid materials to remove unwanted surface species such as water. A furnace is often employed for this step. A dry box is typically used to load the solid samples into the NMR rotor. From there, the rotor is transferred into an exposure device which enables the rotor to be opened under a tightly controlled atmosphere to load a desired gas or mixture into the rotor. Such a device is depicted in Figure 2.

<table>
	<tbody>
		<tr>
			<td>1) Preparation of Solids Samples</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Gas maniforld</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Gas Mass Flow Controllers</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Vacuum Pump</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Tube Furnace</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Temperature Controller</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Thermocouple</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Quartz Tube</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Isolation Valves</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Quartz Wool</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td></td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>2) Loading solid samples into the rotor</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Dry glove box</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>High-temperature, high-pressure NMR rotor</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Sample funnel</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Sample packing rod</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Rotor holder</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Analytical Balance</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Microsyringe</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Rotor cap bit</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td></td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>3) Addition of gases to the rotor</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>NMR loading chamber</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Rotor stage and appropriately sized inserts</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Vacuum Pump</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Gas maniforld</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Gas Mass Flow Controllers</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Vacuum Pump</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Heating Tape</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Temperature Controller</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Thermocouple</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Allen wrench</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Threaded rod</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Wrenchs</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Pressure Gauge</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>High-pressure syringe pump</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Liquid syringe pump</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td></td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>4) Conducting the NMR experiments</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>MAS NMR probe</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>NMR spectrometer</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
		<tr>
			<td>Computer to control the spectrometer</td>
			<td></td>
			<td></td>
			<td></td>
		</tr>
	</tbody>
</table>

high-temperature and high-pressure in situ magic angle spinning nuclear magnetic resonance spectroscopy

Nuclear magnetic resonance (NMR) spectroscopy represents an important technique to understand the structure and bonding environments of molecules. There exists a drive to characterize materials under conditions relevant to the chemical process of interest. To address this, in situ high-temperature, high-pressure MAS NMR methods have been developed to enable the observation of chemical interactions over a range of pressures (vacuum to several hundred bar) and temperatures (well below 0 &#176;C to 250 &#176;C). Further, the chemical identity of the samples can be comprised of solids, liquids, and gases or mixtures of the three. The method incorporates all-zirconia NMR rotors (sample holder for MAS NMR) which can be sealed using a threaded cap to compress an O-ring. This rotor exhibits great chemical resistance, temperature compatibility, low NMR background, and can withstand high pressures. These combined factors enable it to be utilized in a wide range of system combinations, which in turn permit its use in diverse fields as carbon sequestration, catalysis, material science, geochemistry, and biology. The flexibility of this technique makes it an attractive option for scientists from numerous disciplines.

The output from the NMR spectrometer takes the form of a free induction decay (FID) which is the time-domain signal from the excited spins as they relax back to thermodynamic equilibrium. Such an FID resembles Figure 3. When Fourier transformed from the time domain to the frequency domain (frequency to PPM by Equation 3, whereby the difference absolute frequency and a reference is divided by the carrier frequency of the NMR spectrometer), it represents the NMR spectrum for which each peak in...

Watch this Scientific Journal Video about High-Temperature and High-Pressure In situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy at JoVE.com

High-Temperature and High-Pressure In situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy

The molecular structures and dynamics of solids, liquids, gases, and mixtures are of critical interest to diverse scientific fields. High-temperature, high-pressure in situ MAS NMR enables detection of the chemical environment of constituents in mixed phase systems under tightly controlled chemical environments.

Nuclear magnetic resonance (NMR) spectroscopy represents an important technique to understand the structure and bonding environments of molecules. There ...

high-temperature-high-pressure-situ-magic-angle-spinning-nuclear

Research

Education

JoVE Core

JoVE Journal

Analytical Chemistry

Chemistry

Unit 1

Interpreting Nuclear Magnetic Resonance Spectra

SCIENTISTS IN ACTION

5.4K 조회수.  Pacific Northwest National Laboratory. The molecular structures and dynamics of solids, liquids, gases, and mixtures are of critical interest to diverse scientific fields. High-temperature, high-pressure in situ MAS NMR enables detection of the chemical environment of constituents in mixed phase systems under tightly controlled chemical environments.

비디오: High-Temperature and High-Pressure In situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy

In Situ SIMS and IR Spectroscopy of Well-defined Surfaces Prepared by Soft Landing of Mass-selected Ions

Soft landing of mass-selected ions onto surfaces is a powerful approach for the highly-controlled preparation of materials that are inaccessible using conventional synthesis techniques. Coupling soft landing with in situ characterization using secondary ion mass spectrometry (SIMS) and infrared reflection absorption spectroscopy (IRRAS) enables analysis of well-defined surfaces under clean vacuum conditions. The capabilities of three soft-landing instruments constructed in our laboratory are illustrated for the representative system of surface-bound organometallics prepared by soft landing of mass-selected ruthenium tris(bipyridine) dications, [Ru(bpy)3]2+ (bpy = bipyridine), onto carboxylic acid terminated self-assembled monolayer surfaces on gold (COOH-SAMs). In situ time-of-flight (TOF)-SIMS provides insight into the reactivity of the soft-landed ions. In addition, the kinetics of charge reduction, neutralization and desorption occurring on the COOH-SAM both during and after ion soft landing are studied using in situ Fourier transform ion cyclotron resonance (FT-ICR)-SIMS measurements. In situ IRRAS experiments provide insight into how the structure of organic ligands surrounding metal centers is perturbed through immobilization of organometallic ions on COOH-SAM surfaces by soft landing. Collectively, the three instruments provide complementary information about the chemical composition, reactivity and structure of well-defined species supported on surfaces.

In Situ SIMS and IR Spectroscopy of Well-defined Surfaces Prepared by Soft Landing of Mass-selected Ions

Soft landing of mass-selected ions onto surfaces is a powerful approach for the highly-controlled preparation of novel materials. Coupled with analysis by in situ secondary ion mass spectrometry (SIMS) and infrared reflection absorption spectroscopy (IRRAS), soft landing provides unprecedented insights into the interactions of well-defined species with surfaces.

대량 선택 이온 소프트 랜딩에 의해 준비 잘 정의 된 표면의 제자리 SIMS 및 IR 분광법

Soft landing of mass-selected ions onto surfaces is a powerful approach for the highly-controlled preparation of materials that are inaccessible using ...

연구

화학

Sequencing of Plant Wall Heteroxylans Using Enzymic, Chemical (Methylation) and Physical (Mass Spectrometry, Nuclear Magnetic Resonance) Techniques

This protocol describes the specific techniques used for the characterization of reducing end (RE) and internal region glycosyl sequence(s) of heteroxylans. De-starched wheat endosperm cell walls were isolated as an alcohol-insoluble residue (AIR)1 and sequentially extracted with water (W-sol Fr) and 1 M KOH containing 1% NaBH4 (KOH-sol Fr) as described by Ratnayake et al. (2014)2. Two different approaches (see summary in Figure 1) are adopted. In the first, intact W-sol AXs are treated with 2AB to tag the original RE backbone chain sugar residue and then treated with an endoxylanase to generate a mixture of 2AB-labelled RE and internal region reducing oligosaccharides, respectively. In a second approach, the KOH-sol Fr is hydrolyzed with endoxylanase to first generate a mixture of oligosaccharides which are subsequently labelled with 2AB. The enzymically released ((un)tagged) oligosaccharides from both W- and KOH-sol Frs are then methylated and the detailed structural analysis of both the native and methylated oligosaccharides is performed using a combination of MALDI-TOF-MS, RP-HPLC-ESI-QTOF-MS and ESI-MSn. Endoxylanase digested KOH-sol AXs are also characterized by nuclear magnetic resonance (NMR) that also provides information on the anomeric configuration. These techniques can be applied to other classes of polysaccharides using the appropriate endo-hydrolases.

Sequencing of Plant Wall Heteroxylans Using Enzymic, Chemical Methylation and Physical Mass Spectrometry, Nuclear Magnetic Resonance Techniques

This protocol describes the specific techniques used for the structural characterization of reducing end (RE) and internal region glycosyl sequence(s) of heteroxylans by tagging the RE with 2 aminobenzamide prior to enzymatic (endoxylanase) hydrolysis and then analysis of the resultant oligosaccharides using mass spectrometry (MS) and nuclear magnetic resonance (NMR).

This protocol describes the specific techniques used for the characterization of reducing end (RE) and internal region glycosyl sequence(s) of ...

In Situ Monitoring of Diffusion of Guest Molecules in Porous Media Using Electron Paramagnetic Resonance Imaging

A method is demonstrated to monitor macroscopic translational diffusion using electron paramagnetic resonance (EPR) imaging. A host-guest system with nitroxide spin probe 3-(2-Iodoacetamido)-2,2,5,5-tetramethyl-1-pyrrolidinyloxy (IPSL) as a guest inside the periodic mesoporous organosilica (PMO) aerogel UKON1-GEL as a host and ethanol as a solvent is used as an example to describe the protocol. Data is shown from a previous publication, where the protocol has been applied to both IPSL and Tris(8-carboxy-2,2,6,6-perdeutero-tetramethyl-benzo[1,2-d:4,5-d&#8242;]bis(1,3)dithiole) methyl (Trityl) as guest molecules and UKON1-GEL and SILICA-GEL as host systems. 
A method is shown to prepare aerogel samples that cannot be synthesized directly in the sample tube for measurement due to a size change during synthesis. The aerogel is attached to sample tubes using heat shrink tubing and a pressure cooker to reach the necessary temperature without evaporating the solvent in the process. The method does not assume a clearly defined initial distribution of guest molecules at the start of the measurement. Instead, it requires a reservoir on top of the aerogel and experimentally determines the influx rate during data analysis.
The diffusion is monitored continually over a period of 20 hr by recording the 1d spin density profile within the sample. The spectrometer settings for the imaging experiment are described quantitatively. Data analysis software is provided to take the resonator sensitivity profile into account and to numerically solve the diffusion equation. The software determines the macroscopic translational diffusion coefficient by least square minimization of the difference between the experiment and the numerical solution of the diffusion equation.

In Situ Monitoring of Diffusion of Guest Molecules in Porous Media Using Electron Paramagnetic Resonance Imaging

A protocol for the in situ monitoring of the diffusion of guest molecules in porous media using electron paramagnetic resonance (EPR) imaging is presented.

전자 상자성 공명 영상을 이용하여 다공성 미디어에서 고객 분자의 확산의 제자리 모니터링에

A method is demonstrated to monitor macroscopic translational diffusion using electron paramagnetic resonance (EPR) imaging. A host-guest system with ...

High Pressure Single Crystal Diffraction at PX^2

In this report we describe detailed procedures for carrying out single crystal X-ray diffraction experiments with a diamond anvil cell (DAC) at the GSECARS 13-BM-C beamline at the Advanced Photon Source. The DAC program at 13-BM-C is part of the Partnership for Extreme Xtallography (PX^2) project. BX-90 type DACs with conical-type diamond anvils and backing plates are recommended for these experiments. The sample chamber should be loaded with noble gas to maintain a hydrostatic pressure environment. The sample is aligned to the rotation center of the diffraction goniometer. The MARCCD area detector is calibrated with a powder diffraction pattern from LaB6. The sample diffraction peaks are analyzed with the ATREX software program, and are then indexed with the RSV software program. RSV is used to refine the UB matrix of the single crystal, and with this information and the peak prediction function, more diffraction peaks can be located. Representative single crystal diffraction data from an omphacite (Ca0.51Na0.48)(Mg0.44Al0.44Fe2+0.14Fe3+0.02)Si2O6 sample were collected. Analysis of the data gave a monoclinic lattice with P2/n space group at 0.35 GPa, and the lattice parameters were found to be: a = 9.496 &#177;0.006 &#197;, b = 8.761 &#177;0.004 &#197;, c = 5.248 &#177;0.001 &#197;, &#946; = 105.06 &#177;0.03&#186;, &#945; = &#947; = 90&#186;.

In this report, we describe detailed procedures for carrying out single crystal X-ray diffraction experiments with a diamond anvil cell at the GSECARS 13-BM-C beamline at the Advanced Photon Source. ATREX and RSV programs are used to analyze the data.

고압 PX에서 단결정 회절 ^ 2

In this report we describe detailed procedures for carrying out single crystal X-ray diffraction experiments with a diamond anvil cell (DAC) at the ...

Preparation and In Vitro Characterization of Dendrimer-based Contrast Agents for Magnetic Resonance Imaging

Paramagnetic complexes of gadolinium(III) with acyclic or macrocyclic chelates are the most commonly used contrast agents (CAs) for magnetic resonance imaging (MRI). Their purpose is to enhance the relaxation rate of water protons in tissue, thus increasing the MR image contrast and the specificity of the MRI measurements. Current clinically approved contrast agents are low molecular weight molecules that are rapidly cleared from the body. The use of dendrimers as carriers of paramagnetic chelators can play an important role in the future development of more efficient MRI contrast agents. Specifically, the increase in local concentration of the paramagnetic species results in a higher signal contrast. Furthermore, this CA provides a longer tissue retention time due to its high molecular weight and size. Here, we demonstrate a convenient procedure for the preparation of macromolecular MRI contrast agents based on poly(amidoamine) (PAMAM) dendrimers with monomacrocyclic DOTA-type chelators (DOTA &#8211; 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetate). The chelating unit was appended by exploiting the reactivity of the isothiocyanate (NCS) group towards the amine surface groups of the PAMAM dendrimer to form thiourea bridges. Dendrimeric products were purified and analyzed by means of nuclear magnetic resonance spectroscopy, mass spectrometry, and elemental analysis. Finally, high resolution MR images were recorded and the signal contrasts obtained from the prepared dendrimeric and the commercially available monomeric agents were compared.

Preparation and In Vitro Characterization of Dendrimer-based Contrast Agents for Magnetic Resonance Imaging

This protocol describes the preparation and characterization of a dendrimeric magnetic resonance imaging (MRI) contrast agent that carries cyclen-based macrocyclic chelates coordinating paramagnetic gadolinium ions. In a series of MRI experiments in vitro, this agent produced an amplified MRI signal when compared to the commercially available monomeric analogue.

준비 및<em&gt; 체외</em&gt; 자기 공명 영상에 대한 덴드리머 기반 대조 대리인의 특성

Paramagnetic complexes of gadolinium(III) with acyclic or macrocyclic chelates are the most commonly used contrast agents (CAs) for magnetic resonance ...

In Situ Detection and Single Cell Quantification of Metal Oxide Nanoparticles Using Nuclear Microprobe Analysis

Micro-analytical techniques based on chemical element imaging enable the localization and quantification of chemical composition at the cellular level. They offer new possibilities for the characterization of living systems and are particularly appropriate for detecting, localizing and quantifying the presence of metal oxide nanoparticles both in biological specimens and the environment. Indeed, these techniques all meet relevant requirements in terms of (i) sensitivity (from 1 up to 10 &#181;g.g-1 of dry mass), (ii) micrometer range spatial resolution, and (iii) multi-element detection. Given these characteristics, microbeam chemical element imaging can powerfully complement routine imaging techniques such as optical and fluorescence microscopy. This protocol describes how to perform a nuclear microprobe analysis on cultured cells (U2OS) exposed to titanium dioxide nanoparticles. Cells must grow on and be exposed directly in a specially designed sample holder used on the optical microscope and in the nuclear microprobe analysis stages. Plunge-freeze cryogenic fixation of the samples preserves both the cellular organization and the chemical element distribution. Simultaneous nuclear microprobe analysis (scanning transmission ion microscopy, Rutherford backscattering spectrometry and particle induced X-ray emission) performed on the sample provides information about the cellular density, the local distribution of the chemical elements, as well as the cellular content of nanoparticles. There is a growing need for such analytical tools within biology, especially in the emerging context of Nanotoxicology and Nanomedicine for which our comprehension of the interactions between nanoparticles and biological samples must be deepened. In particular, as nuclear microprobe analysis does not require nanoparticles to be labelled, nanoparticle abundances are quantifiable down to the individual cell level in a cell population, independently of their surface state.

In Situ Detection and Single Cell Quantification of Metal Oxide Nanoparticles Using Nuclear Microprobe Analysis

We describe a procedure for the detection of chemical elements present in situ in human cells as well as their in vitro quantification. The method is well-suited to any cell type and is particularly useful for quantitative chemical analyses in single cells following in vitro metal oxide nanoparticles exposure.

제자리에서 검색 및 핵 현미경 분석을 사용 하 여 금속 산화물 나노 입자의 단일 셀 정량화

Micro-analytical techniques based on chemical element imaging enable the localization and quantification of chemical composition at the cellular level. ...

Non-equilibrium Microwave Plasma for Efficient High Temperature Chemistry

A flowing microwave plasma based methodology for converting electric energy into internal and/or translational modes of stable molecules with the purpose of efficiently driving non-equilibrium chemistry is discussed. The advantage of a flowing plasma reactor is that continuous chemical processes can be driven with the flexibility of startup times in the seconds timescale. The plasma approach is generically suitable for conversion/activation of stable molecules such as CO2, N2 and CH4. Here the reduction of CO2 to CO is used as a model system: the complementary diagnostics illustrate how a baseline thermodynamic equilibrium conversion can be exceeded by the intrinsic non-equilibrium from high vibrational excitation. Laser (Rayleigh) scattering is used to measure the reactor temperature and Fourier Transform Infrared Spectroscopy (FTIR) to characterize in situ internal (vibrational) excitation as well as the effluent composition to monitor conversion and selectivity.

This article describes a flowing microwave reactor that is used to drive efficient non-equilibrium chemistry for the application of conversion/activation of stable molecules such as CO2, N2 and CH4. The goal of the procedure described here is to measure the in situ gas temperature and gas conversion.

효율적인 고온 화학을위한 비평 형 마이크로 웨이브 플라즈마

A flowing microwave plasma based methodology for converting electric energy into internal and/or translational modes of stable molecules with the purpose ...

Microfluidic Dry-spinning and Characterization of Regenerated Silk Fibroin Fibers

The protocol demonstrates a method for mimicking the spinning process of silkworm. In the native spinning process, the contracting spinning duct enables the silk proteins to be compact and ordered by shearing and elongation forces. Here, a biomimetic microfluidic channel was designed to mimic the specific geometry of the spinning duct of the silkworm. Regenerated silk fibroin (RSF) spinning doped with high concentration, was extruded through the microchannel to dry-spin fibers at ambient temperature and pressure. In the post-treated process, the as-spun fibers were drawn and stored in ethanol aqueous solution. Synchrotron radiation wide-angle X-ray diffraction (SR-WAXD) technology was used to investigate the microstructure of single RSF fibers, which were fixed to a sample holder with the RSF fiber axis normal to the microbeam of the X-ray. The crystallinity, crystallite size, and crystalline orientation of the fiber were calculated from the WAXD data. The diffraction arcs near the equator of the two-dimensional WAXD pattern indicate that the post-treated RSF fiber has a high orientation degree.

A protocol for the microfluidic spinning and microstructure characterization of regenerated silk fibroin monofilament is presented.

미세 드라이 회전 및 재생성된 실크 Fibroin 섬유의 특성

The protocol demonstrates a method for mimicking the spinning process of silkworm. In the native spinning process, the contracting spinning duct enables ...

A Convenient Method for Extraction and Analysis with High-Pressure Liquid Chromatography of Catecholamine Neurotransmitters and Their Metabolites

The extraction and analysis of catecholamine neurotransmitters in biological fluids is of great importance in assessing nervous system function and related diseases, but their precise measurement is still a challenge. Many protocols have been described for neurotransmitter measurement by a variety of instruments, including high-pressure liquid chromatography (HPLC). However, there are shortcomings, such as complicated operation or hard-to-detect multiple targets, which cannot be avoided, and presently, the dominant analysis technique is still HPLC coupled with sensitive electrochemical or fluorimetric detection, due to its high sensitivity and good selectivity. Here, a detailed protocol is described for the pretreatment and detection of catecholamines with high pressure liquid chromatography with electrochemical detection (HPLC-ECD) in real urine samples of infants, using electrospun composite nanofibers composed of polymeric crown ether with polystyrene as adsorbent, also known as the packed-fiber solid phase extraction (PFSPE) method. We show how urine samples can be easily precleaned by a nanofiber-packed solid phase column, and how the analytes in the sample can be rapidly enriched, desorbed, and detected on an ECD system. PFSPE greatly simplifies the pretreatment procedures for biological samples, allowing for decreased time, expense, and reduction of the loss of targets. 
Overall, this work illustrates a simple and convenient protocol for solid-phase extraction coupled to an HPLC-ECD system for simultaneous determination of three monoamine neurotransmitters (norepinephrine (NE), epinephrine (E), dopamine (DA)) and two of their metabolites (3-methoxy-4-hydroxyphenylglycol (MHPG) and 3,4-dihydroxy-phenylacetic acid (DOPAC)) in infants' urine. The established protocol was applied to assess the differences of urinary catecholamines and their metabolites between high-risk infants with perinatal brain damage and healthy controls. Comparative analysis revealed a significant difference in urinary MHPG between the two groups, indicating that the catecholamine metabolites may be an important candidate marker for early diagnosis of cases at risk for brain damage in infants.

We present a convenient solid-phase extraction coupled to high-pressure liquid chromatography (HPLC) with electrochemical detection (ECD) for simultaneous determination of three monoamine neurotransmitters and two of their metabolites in infants' urine. We also identify the metabolite MHPG as a potential biomarker for the early diagnosis of brain damage for infants.

추출 및 카 테 콜 아민 신경 전달 물질과 그들의 대사 산물의 고압 액체 크로마토그래피로 분석 하는 편리한 방법

The extraction and analysis of catecholamine neurotransmitters in biological fluids is of great importance in assessing nervous system function and ...

DNA-magnetic Particle Binding Analysis by Dynamic and Electrophoretic Light Scattering

Isolation of DNA using magnetic particles is a field of high importance in biotechnology and molecular biology research. This protocol describes the evaluation of DNA-magnetic particles binding via dynamic light scattering (DLS) and electrophoretic light scattering (ELS). Analysis by DLS provides valuable information on the physicochemical properties of particles including particle size, polydispersity, and zeta potential. The latter describes the surface charge of the particle which plays major role in electrostatic binding of materials such as DNA. Here, a comparative analysis exploits three chemical modifications of nanoparticles and microparticles and their effects on DNA binding and elution. Chemical modifications by branched polyethylenimine, tetraethyl orthosilicate and (3-aminopropyl)triethoxysilane are investigated. Since DNA exhibits a negative charge, it is expected that zeta potential of particle surface will decrease upon binding of DNA. Forming of clusters should also affect particle size. In order to investigate the efficiency of these particles in isolation and elution of DNA, the particles are mixed with DNA in low pH (~6), high ionic strength and dehydration environment. Particles are washed on magnet and then DNA is eluted by Tris-HCl buffer (pH = 8). DNA copy number is estimated using quantitative polymerase chain reaction (PCR). Zeta potential, particle size, polydispersity and quantitative PCR data are evaluated and compared. DLS is an insightful and supporting method of analysis that adds a new perspective to the process of screening of particles for DNA isolation.

This protocol describes the synthesis of magnetic particles and evaluation of their DNA-binding properties via dynamic and electrophoretic light scattering. This method focuses on monitoring changes in particle size, their polydispersity and zeta potential of particle surface which play major role in binding of materials such as DNA.

역동적이 고 전기 이동 산란 분석 바인딩 DNA-마그네틱 입자

Isolation of DNA using magnetic particles is a field of high importance in biotechnology and molecular biology research. This protocol describes the ...