Large Volume, Behaviorally-relevant Illumination for Optogenetics in Non-human Primates

Podsumowanie

A protocol to build a tissue penetrating illuminator for delivering light over large volumes with minimal diameter is presented.

Streszczenie

This protocol describes a large-volume illuminator, which was developed for optogenetic manipulations in the non-human primate brain. The illuminator is a modified plastic optical fiber with etched tip, such that the light emitting surface area is > 100x that of a conventional fiber. In addition to describing the construction of the large-volume illuminator, this protocol details the quality-control calibration used to ensure even light distribution. Further, this protocol describes techniques for inserting and removing the large volume illuminator. Both superficial and deep structures may be illuminated. This large volume illuminator does not need to be physically coupled to an electrode, and because the illuminator is made of plastic, not glass, it will simply bend in circumstances when traditional optical fibers would shatter. Because this illuminator delivers light over behaviorally-relevant tissue volumes (≈ 10 mm³) with no greater penetration damage than a conventional optical fiber, it facilitates behavioral studies using optogenetics in non-human primates.

Wprowadzenie

Optogenetic tools, which allow for millisecond-precise, light-driven neuronal control are widely used to study functional physiology and behavior in rodents and invertebrates. However, technical challenges have limited the use of optogenetics in the non-human primate brain, which has a volume ~100x larger than the rodent brain ¹.

To facilitate optogenetics studies in non-human primates, an illuminator was designed to address two competing goals: large volume illumination and minimal penetration damage. Previous attempts to address one of these concerns have come at the expensive of the other. Bundles of fibers illuminate larger volumes but with increased diameter, and, thus, damage^2,3. Tapered glass fibers reduce penetration damage, but narrowly focus light to light emitting surface areas <100 µm^{2 4,5}. External brain illumination through a window in the dura circumvents the challenge of penetration damage and may allow for large volume illumination, but it can only be used for a few superficial brain areas⁶.

To create a large-volume, small diameter illuminator (Figure 1a), the tip of a plastic optical fiber is heat tapered and the core and cladding are etched (Figure 1b,c). Unlike other tapered fibers that focus light to a narrow point, the etching allows light to escape evenly out the sides of the tip, thus, distributing light broadly over a large area (Figure 1d,e). Because penetration damage is proportional to penetration diameter, this illuminator has no more penetration damage than a conventional fiber, yet it has >100x the light emitting surface area and delivers light more broadly with 1/100th the light power density in a brain phantom (1.75% agarose) (Figure 1e). A Monte Carlo model (Figure 1f) illustrates the difference in light spread between a conventional fiber and the large volume illuminator when they have equal light power densities as their light emitting surfaces. Each illuminator is individually calibrated using an integrating sphere (Figure 2a,b) to ensure even light distribution along the tip (Figure 2c).

This large volume illuminator has been validated with optogenetic manipulation of both behavior and neuronal firing in non-human primates. The fiber tip length may be customized to any brain area and to each animal’s individual receptive field map. The illuminator may be paired with a penetrating electrode for neuronal recordings that span the length of illumination. Further, because the fiber can carry any color of visible light, it can be paired with any of the available optogenetic molecules available.

Access restricted. Please log in or start a trial to view this content.

Protokół

Note: All animal procedures were in accordance with the NIH guidelines and were approved by the Massachusetts Institute of Technology Committee on Animal Care.

1. Illuminator Fabrication

1. Use a pair of sharp shears to cut a section of 250 µm diameter plastic optical fiber that is at least 10 cm longer than the desired total illuminator length.
2. Remove 15 - 20 cm of polyethylene jacket from one end of the plastic optical fiber using a 22 gauge wire stripper.
3. Secure the distal most 3 - 5 cm of the stripped end of the fiber in a table vise clamp.
4. Hold the jacketed end of the fiber taut in one hand with a constant steady pull. The fiber should be parallel to the floor, perpendicular to the vice. Maintain this constant tension on the fiber throughout heating and cooling (Steps 1.5 and 1.6 below) so that the fiber remains straight and taut as it thins.
5. Using the lowest setting of a dual temperature heat gun (570/1,000 °F,), heat the stripped section of the fiber until it is thinned to a diameter of 60 - 100 μm, or about the diameter of a human hair.
6. Maintain the constant tension on the fiber while allowing the fiber to cool. Failure to maintain tension may cause the fiber to curl.
7. Confirm the diameter of the thinned tip under a dissecting microscope. Alternately, one may use calipers instead.
   1. If the fiber is not thin enough, repeat steps 1.4 through 1.6 as needed to achieve the desired tip diameter.
   2. Optional if re-pulling, put a small mark at the narrowest portion of the fiber if it will be heated again so that the center of the heat gun targets the narrowest portion of the fiber.
   3. If the fiber is too thin, start over.
8. Once the fiber has full cooled and the desired diameter has been achieved, pinch the fiber 3 cm from the narrowest point on either side. With a quick, sharp pull along the axis of the fiber, separate the sides to create a tapered tip.
9. Examine the tapered tip under a low power (e.g., 4X) on dissection microscope. If the tip is forked or curled (Figure 1f), discard the fiber.
10. Prepare to etch the tapered tip by placing a piece of lab tape near the end of the tip, leaving the last 5 mm exposed. The tape protects the fiber from etching above the desired length of light emission. This tip length was selected based on thickness of primate cortex in the target region. A longer or shorter length could be exposed depending on the desired length of illumination. If a different etch tip length is desired, the edge of the lab tape can be moved closer to or farther from the tapered tip.
11. Fold a small (~1 inch x 2 inch) square of 5 μm silicon carbide lapping sheet over between the thumb and forefinger. Place the tip of the fiber between the two sides of the lapping sheet and gently etch the fiber using small circular motions, as if rolling a BB between the thumb and forefinger. Frequently rotate the fiber so that all sides are etched evenly. The fiber tip will appear “roughened” to the naked eye in areas that have been etched, while un-etched areas typically appear smooth.
12. Repeat step 1.11 with a 3 μm aluminum oxide lapping sheet.
13. Affix a connector on the end of the illuminator opposite to the etched tip. This allows the illuminator to connect to an optical cable or laser.
    Note: This method differs from the preferred method for fixing glass / silica optical fibers in ferrules. Because the metal ferrule is harder than the plastic optical fiber, polishing the fiber and ferrule as a unit after gluing can damage the plastic optical fiber as tiny shards of metal produced during the polishing process can embed themselves in flat-cleaved fiber.
    1. Remove about 5 mm of the polyethylene jacket from the opposite end of the illuminator using a 22 gauge wire stripper.
    2. Cut the opposite end flat with a hot knife to smooth the surface.
    3. Polish the opposite end flat with successively finer lapping sheets: 5 µm, 3 μm, 1 μm and 0.3 µm.
    4. Insert the flat opposite end into a 260 µm inner diameter stainless steel ferrule until it is flush with the end of the ferrule.
    5. Visually confirm that the opposite end is smoothly and evenly polished with a fiber microscope.
    6. Remove the fiber from the ferrule and tape the ferrule vertically on the edge of a table with the fiber pointing down.
    7. Fill a 1 mL syringe with plastic epoxy and attach a blunt 18 gauge needle to the syringe.
    8. Use the needle to apply epoxy down into the ferrule. Fill the ferrule completely with epoxy.
    9. Insert the fiber into the ferrule.
    10. Wipe any excess epoxy from polished surface of the fiber with a wet lint-free wipe prior to drying if needed. Otherwise, excess epoxy can be removed after 12 - 24 h.
    11. Store the fiber gently until calibration and place a dust cap over the ferrule.

2. Illuminator Calibration and Quality Control

Note: These methods for calibration assess for light output non-linearity at different distances from the tip of the fiber. Uneven light distribution typically results from a “bumpy” or “wavy” taper.

1. Create a light shielding diaphragm for the top of the integrating sphere using light absorbing foil (Figure 2).
   Note: Wear gloves whenever handling light absorbing foil to prevent skin oils from creating light reflecting smudges.
   1. Fold a 2” by 4” piece of light absorbing foil over on itself to form a 2” x 2” square.  An alternative method is to cut a 2” x 2” square with one light absorbing side and one light reflecting side (i.e., a side of standard aluminum foil); however, the fold-over method is safer because it provides a dull edge for handling the diaphragm in the next step. 
   2. Fold lab tape or electrical tape along the edges of the square to bind the non-folded edges. This both holds the sides together and protects against cuts from sharp edges.
   3. Puncture a hole in the center of the square using a 26 gauge needle.
   4. Remove the large screw on cap from the integrating sphere and cover the opening with the diaphragm. Place the hole over the center. If the diaphragm was created with one light absorbing and one light reflecting side, place the light absorbing side up and the light reflecting side down, facing the inside of the integrating sphere.
      Note: To prevent dust and debris from entering the integrating sphere and to keep the hole centered, secure the diaphragm to the outside of the integrating sphere with lab tape.
2. Measure light output along the tip in 500 µm increments using a micromanipulator or stereotaxic arm and an integrating sphere.
   Note: Safety goggles of the appropriate wavelength should be worn whenever the laser is on.
   1. Connect the opposite end of the fiber to a laser or light source, but do not trigger light output yet.
   2. Secure the illuminator to a stereotaxic holder (preferably with lab tape) with the tip 7 - 10 mm below the bottom of the holder.
   3. Screw the stereotaxic holder into the stereotaxic arm.
   4. Align the tip of the illuminator with the hole in the center of the diaphragm. Zero the micromanipulator when the tip is at the exact same level as the diaphragm.
   5. Turn off the room lights and zero the integrating sphere.
   6. Trigger the laser (or other light source) and measure the total light power output using the integrating sphere.
      Note: Use the lowest light output possible for calibration testing.
   7. Lower the fiber 500 µm into the integrating sphere and repeat step 2.2.6.
   8. Continue lowering the fiber into the integrating sphere and measuring total light output in 500 µm increments until the total light power levels off.
      Caution: Total light power should level off once the entire tip is in the sphere. Do not continue to lower the fiber more than 1 - 2 mm beyond the etched tip length. If the tip contacts the bottom of the integrating sphere, it may melt and/or ruin the integrating sphere.
3. Confirm an evenly etched fiber by plotting total light power output as a function of how far the fiber has been lowered into the integrating sphere to confirm linearity.

3. In Vivo Illumination

Note: Here, these methods are shown using a plastic model rather than a non-human primate.

1. Implant a 25 mm diameter recording chamber was implanted over the brain area of interest prior to experimentation.
2. Perform anatomical magnetic resonance imaging (MRI) prior to experimentation. Place a custom recording grid in the chamber and fill it with sterile surgical lubricant to allow for grid visualization and determination of the level of the dura and target brain structures.
3. Prepare a tower micro-drive prior to each testing session.
   1. Affix a 25 gauge guide tube with beveled tip to the middle and lower clamps on the drive. Two clamps are used to ensure that the guide tube remains straight. Both of these clamps can be moved manually if desired.
      Note: The guide tube may be epoxied or soldered to the clamps.
   2. Secure the large volume illuminator in the upper clamp on the same drive. This clamp is attached to the drive motor.
   3. Thread the large-volume illuminator through the guide tube fully and confirm that the tip of the illuminator extends past the tip of the guide tube.
      Note: The length of illuminator that extends past the tip of the guide tube equals the distance from the dura to the lower margin of the target brain region, as determined via MRI.
   4. Soak the guide tube and illuminator in antiseptic solution (e.g., chlorohexidine) to sterilize.
4. Place a custom sterilized grid inside the clean chamber and secure it at a pre-specified orientation with a screw on the side of the chamber. The grid shown here has 1 mm spacing; however, the spacing can be customized as needed.
   Note: This should be identical to the grid and orientation used in the anatomical MRI.
5. Secure the stereotactic micro-drive holder on the recording chamber in a pre-determined orientation.
6. Retract the sterilized illuminator from the guide tube by pulling the illuminator up using sterile, blunt forceps. The tip of the illuminator should be 5 - 10 mm above the tip of guide tube.
   Note: The illuminator will bow outward between the guide tube and the clamp. This will not damage the flexible illuminator.
7. Affix the micro-drive to the holder and place the guide tube into target grid hole.
8. Lower the micro-drive stage until the guide tube is just through the level of the dura.
   Note: If desired, a second micro-drive with an electrode can be placed on the stage and lowered into a different grid hole. The local field potential on this electrode will show a distance-dependent light artifact, which can be used to confirm illuminator placement.
9. Attempt the lower the illuminator manually with sterile forceps.
   1. If there is any resistance, retract the illuminator 5 - 10 mm, wait 10 min to allow the tissue to settle and try again.
   2. If there is still resistance on the second attempt, retract the illuminator tip into the guide tube, lower the guide tube 0.25 mm, and try again.
   3. Repeat until the illuminator slides through the guide tube without any resistance.
   4. Lower the illuminator until it is taut.
      Caution: Do not push the illuminator forcefully against resistance. In these cases the guide tube typically has not penetrated the dura fully. Pushing the fiber forcefully will cause it to bend on itself, preventing the fiber from entering the brain and possibly destroying the tip (Figure 1g).
10. Connect the ferrule on the other end of the illuminator to the larger optics set up or laser.
11. Ensure that no light is visible to the non-human primate.
    1. Use black-out shielding or light absorbing foil to fully encompass the recording towers.
    2. Place all optical connections in shielded envelopes made of light absorbing foil.
    3. Shield all patch cables with either light absorbing foil or black electrical tape.
    4. As an extra precaution, place a decoy light-emitting diode (LED) bank of the same light color used in the experiment behind the non-human primate and flash the LEDs continuously at 2.5 Hz. This prevents the eyes from adjusting fully to darkness. If there were inadvertent light leakage, this flashing light would help to prevent the leak from serving as a behavioral trigger.

Access restricted. Please log in or start a trial to view this content.

Wyniki

The illumination of large brain volumes in non-human primates allows for behaviorally-relevant optogenetic manipulation. Acker et al. (2016) used this large volume illuminator with the red-shifted Halorhodopsin, Jaws ⁷ to study the temporal contribution of the frontal eye field (FEF) to memory-guided saccades in two rhesus monkeys. Specifically, FEF neurons were injected with a viral vector containing Jaws and then illuminated with red-light using the large volume illuminator during eithe...

Access restricted. Please log in or start a trial to view this content.

Dyskusje

While optogenetic tools are widely used to study disease and physiology in rodents, the technical challenge of illuminating large brain volumes has limited the use of optogenetics in non-human primates. Pioneering studies in monkeys used large light power densities (~100 mW/mm² to 20 W/mm²) to illuminate small volumes, perhaps < 1 mm³, and reported modest behavioral effects with excitatory opsins in the cortex^4,9,

Access restricted. Please log in or start a trial to view this content.

Materiały

Name	Company	Catalog Number	Comments
Plastic optical fiber	Industrial fiber optics	SK-10	250 micron diameter, Super Eska line
Wire stripper	Klein Tools	11047	22 gauge
Vise Clamp	Wilton	11104	Generic table mount vice clamp
Dual temperature heat gun	Milwaukee	8975-6	570 / 1,000 °F
Lab marker	VWR	52877
Dissection microscope	VistaVision	82027-156	Stereo microscope w/ dual incandescent light, 2X/4X magnification, available from VWR
Lab tape	VWR	89097-972	4 pack of violet color; however, tape color does not matter
Silicon carbide lapping sheet	ThorLabs	LF5P	5 micron grit, 10 pack
Aluminum oxide lapping sheet	ThorLabs	LF3P	3 micron grit, 10 pack
Aluminum oxide lapping  sheet	ThorLabs	LF1P	1 micron grit, 10 pack
Calcined alumina lapping sheet	ThorLabs	LF03P	0.3 micron grit, 10 pack
Hot knife	Industrial fiber optics	IF370012	60 Watt, heavy duty
Fiber inspection scope	ThorLabs	FS201	optional
Stainless Steel Ferrule	Precision fiber optics	MM-FER2003SS-265	265 micron inner diameter
1 mL syringe	BD	14-823-30	Luer-lok tip is preferable to reduce risk of leakage, but not strictly needed
Plastic epoxy	Industrial fiber optics	40 0005
18 gauge blunt needle	BD	305180	1.5 inch length
Lint-free wipe (KimWipe)	ThorLabs	KW32	available from many vendors
Light absorbing foil	ThorLabs	BKF12
Electrical tape	3M	Temflex 1700	Optional, may substitute other brands / models
26 gauge sharp needle	BD	305111	0.5 inch length
Micromanipulator	Siskiyou	70750000E	may substitute other brands/models
Steretactic arm	Kopf	1460	may substitute other brands/models
Laser safety goggles	KenTeK	KCM-6012	must be selected based on the color of laser used, example given here
Laser or other light source	vortran	Stradus 473-50	example of blue laser
Integrating sphere	ThorLabs	S142C	Attached power meter, also available from ThorLabs, item #PM100D
Ultem recording chamber	Crist instrument company	6-ICO-J0	Customized with alignment notch
Tower microdrive with clamps	NAN	DRTBL-CMS
Guide tube	Custom	N/A	Made from 25 gauge spinal needle (BD) or blunt tubing
NAN driver system	NAN	NANDrive
Custom grid design	custom	custom	plans available upon request
Blunt forceps	FischerScientific	08-875-8A	generic stainless steel blunt forceps
Digital calipers	Neiko	01407A	available on amazon.com. May select a finer resolution caliper for more precise measurements.
Patch cable	ThorLabs	FG200LCC-custom	This is one example of many possible patch cables. As long as the fiber diameter is less than or equal to the fiber diameter of the large volume illuminator and as long as the connectors interface, any patch cable (glass or plastic, vendor purchased or made in the lab) is fine for this application.
Clear plastic dust caps	ThorLabs	CAPF	Package of 25
ceramic split mating sleeve	Precision Fiber Products, Inc.	SM-CS1140S