Multimodal Volumetric Retinal Imaging by Oblique Scanning Laser Ophthalmoscopy (oSLO) and Optical Coherence Tomography (OCT)

Podsumowanie

Here, we present a protocol to get a large field of view (FOV) three-dimensional (3D) fluorescence and OCT retinal image by using a novel imaging multimodal platform. We will introduce the system setup, the method of alignment, and the operational protocols. In vivo imaging will be demonstrated, and representative results will be provided.

Streszczenie

While fluorescence imaging is widely used in ophthalmology, a large field of view (FOV) three-dimensional (3D) fluorescence retinal image is still a big challenge with the state-of-the-art retinal imaging modalities because they would require z-stacking to compile a volumetric dataset. Newer optical coherence tomography (OCT) and OCT angiography (OCTA) systems overcome these restrictions to provide three-dimensional (3D) anatomical and vascular images, but the dye-free nature of OCT cannot visualize leakage indicative of vascular dysfunction. This protocol describes a novel oblique scanning laser ophthalmoscopy (oSLO) technique that provides 3D volumetric fluorescence retinal imaging. The setup of the imaging system generates the oblique scanning by a dove tail slider and aligns the final imaging system at an angle to detect fluorescent cross-sectional images. The system uses the laser scanning method, and therefore, allows an easy incorporation of OCT as a complementary volumetric structural imaging modality. In vivo imaging on rat retina is demonstrated here. Fluorescein solution is intravenously injected to produce volumetric fluorescein angiography (vFA).

Wprowadzenie

Ophthalmology and vision science greatly benefit from the modern optical imaging techniques, since the retina can be easily accessed with light. Fluorescence retinal imaging is an essential tool in the diagnosis and management of chorioretinal vascular diseases such as diabetic retinopathy (DR) and age-related macular degeneration (AMD), both of which are leading causes of blindness in the United States.

However, it is still challenging to acquire a large field of view (FOV), three-dimensional (3D) retinal imaging by using fluorescence imaging. Fundus photography does not have the depth-resolving capability and does not reject diffuse light. As a result, the mixing of signals from different depth reduces the image quality. Scanning laser ophthalmoscopy (SLO) and confocal SLO (cSLO) can reduce the effect of diffused light by using confocal gating¹. However, it is difficult for SLO or cSLO to acquire a 3D human retinal image due to the limit of their depth of focus. Adaptive optics SLO (AOSLO) can provide superb resolution and contrast by correcting for the wavefront aberrations introduced by the human eye. However, AOSLO would still need z-stacking for volumetric imaging². Optical coherence tomography (OCT)³ and OCT angiography (OCTA) systems overcome these restrictions to provide three-dimensional (3D) anatomical and vascular images^4,5,6, but the dye-free nature of OCT cannot visualize leakage indicative of vascular dysfunction.

This protocol describes a novel multimodal platform for 3D volumetric fluorescence retinal imaging, namely oblique scanning laser ophthalmoscopy (oSLO). In this imaging system, an oblique scanning is generated by a dove tail slider, and a final imaging system is aligned in an angle to detect fluorescence cross sectional images. The system uses laser scanning methods, and these techniques allow easy incorporation with OCT as a complementary volumetric structural imaging modality. The current depth resolution is about 25 µm in the rat retina and the field of view is 30°. Essentially, the oSLO allows a fluorescent version of OCT and can be simultaneously combined with OCT and OCTA over a large FOV.

In this protocol, we will describe the setup of the oSLO, the method of alignment and construction, the method of in vivo imaging of rat retina, and the representative results.

Protokół

All methods described here have been approved by the Animal Care and Use Committee (ACUC) of Boston Medical Center.

1. System Setup

1. oSLO System
   1. Use a supercontinuum laser source as the system laser source.
      1. Separate the visible light range (450-650 nm) from higher wavelength range (650-2000 nm) by a dichroic mirror (DM1). Expand the spectrum with a pair of dispersive prisms after the beam passing through a polarization beam splitter (PBS).
      2. Place a slit to select the excitation wavelength range (475-495 nm). Use a reflective mirror to reflect the filtered beam back to the prism pair and then couple the light into a single mode fiber (SMF 1).
      3. Use a spectrometer to confirm the wavelength selection at the output of the single mode fiber.
   2. Connect the single mode fiber to two cascaded optical fiber couplers as shown in Figure 2. One of the fiber output port from the second fiber coupler delivers the light to the oSLO system.
   3. Collimate the laser first in the oSLO system.
      1. Deflect the laser by a galvanometer mirror (GM1). Relay the laser to a second galvanometer mirror (GM2) by a 1:1 telescope system, and further relay to the pupil of the eye by a 3:1 telescope system.
      2. Install a dichroic mirror (DM2) within the 3:1 telescope system to reflect the fluorescence signals.
   4. Mount the 3:1 telescope system and the dichroic mirror (DM2) on a customized dove tail slider to offset the optical axis and create the oblique scanning illumination as shown in Figure 3. Use a caliper to precisely control the offset length as desired.
   5. Fluorescence imaging optical path.
      1. Reflect the fluorescence by the dichroic mirror and relay to the third galvanometer mirror to de-scan the slow scanning.
      2. Relay the light to an imaging objective lens by another 1:1 telescope system. Install the above optics on a translation stage.
         NOTE: Two additional translation stages are installed under the third galvanometer mirror (GM3) to provide redundancy in the degrees of freedom for optimizing the imaging.
   6. Mount a final imaging system on a stage that has three degrees of freedom (rotation, and two axis of translation). Use a planar camera to capture the cross-sectional fluorescence images.
2. Optical Coherence Tomography System
   1. Use the same supercontinuum laser source as the system laser source.
      1. Separate the near infrared (NIR) range (650-900 nm) from the remaining light (650-2000 nm) by another dichroic mirror (DM3). Use a long pass filter to further limit the bandwidth to 800-900 nm. Couple the beam into a single mode fiber (SMF 2).
   2. Connect the single mode fiber to the other input port of the two cascaded optical fiber couplers to combine with the blue oSLO excitation. Direct the light from the second output port of the second fiber coupler to the OCT reference arm, which has a variable neutral density filter (VNDF), dispersion compensation plates and a reflective mirror.
      NOTE: The light returned from the reference arm and the eye recombines at the second optical fiber coupler and is delivered to the OCT spectrometer to collect the signal.
3. Data Acquisition
   1. Use a data acquisition system software written in LabVIEW and modified from the scanning protocol of OCTA^7,8,9,10. For each B-scan, an 80% duty cycle saw tooth with 500 steps is output by an analog output board (AO1) to control the x' fast scanning mirror, GM2.
   2. Trigger the line scan camera at each step to acquire data for the OCT only when the mirror is in the forward scanning direction. Set the exposure time for the line scan camera to be 17 µs.
   3. To acquire the OCTA signal, repeat the measurement 5 times at the same B-scan location.
   4. Set the AO output rate at 100 kHz, and the OCT A-line rate at 50 kHz. Control the y' slow scanning mirror, GM1, by a ramping waveform. Synchronize the de-scanning mirror, GM3, with GM1 to de-scan the slow scanning.
   5. Trigger the planar camera by another analog output board (AO2) to capture one fluorescent image at each y' location. Crop the imaging size or bin the neighbor pixels to increase the speed and sensitivity as desired.

2. System Alignment

1. Adjust the slit in the oSLO light source to select the blue excitation wavelength. Use a spectrometer to monitor the spectral range to be around 475-490 nm.
2. Adjust the dove tail mount slider to shift the optical axis by ~5 mm. This will result in an offset at the rat pupil by ~1.7 mm, resulting in an oblique angle of ~15° on the retina.
3. Adjust the translation stage of the fluorescence detection optics by the same 5 mm.
4. Adjust the final fluorescence imaging system to be ~30°.
5. Measure the optical power using a power meter. Make sure the blue oSLO excitation power is ≤0.2 mW and the OCT laser power ≤0.8 mW, which will not cause retina damage.
   NOTE: Based on the ANSI standard, the maximum permissive exposure (MPE) to the retina is at the level of ~2mW^7,8 in visible light range. According to the formula by Delori et al.⁹, the MPE for the near infrared light is about two times higher than the visible light, at about 4 mW.

3. In Vivo Animal Experiment

1. Transfer a 12-weeks male Long Evans rat into the induction chamber. Anesthetize the rat with 4.5% isoflurane in oxygen for 10 minutes with a flow rate of 2 L/min by an isoflurane vaporizer.
   1. Confirm depth of anesthesia as determined by a lack of withdrawal reflex during an interdigital pinch.
2. After the induction, place the rat on a 5-axis (x, y, z translations, yaw and pitch) holder. Provide supplemental heat by use of a heated stage, circulating warm water blanket or other suitable method in a prolonged experiment. Maintain the anesthesia at 1.5% of isofluorane with a flow rate of 2 liter/minutes during the remaining part of the experiment. When not using an induction chamber with active exhaust, the induction chamber should be placed on a backdraft or downdraft table or under a snorkel to scavenge isoflurane.
3. Dilate the pupil with 1% Tropicamide ophthalmic solution for 2 minutes. Apply 0.5% Tetracaine HCl ophthalmic solution on the rat's eye for additional local anesthesia, if necessary. Keep the eye moisturized with commercial artificial tears at least once every minute during the experiment.
4. Inject fluorescein salt (10% w/w) or FITC (10% w/w) diluted in sterile saline (0.1-0.3 mL) through the tail vein with a 1 mL syringe and a 29G needle.
5. Turn on the laser source. Place a neutral density filter to attenuate the blue light excitation during alignment. Measure the power of the OCT light to be ~0.8 mW, and the blue light <0.01 mW to avoid the formation of cataracts.
6. Start the galvanometer scanning and alignment mode. Adjust the height of the eye ball to make a stationary laser spot on the cornea. Adjust the rat eye position to make the rim of the pupil roughly perpendicular to the laser, and offset the laser to the apical center of the eye to about ~1.5 mm.
7. Further adjust the animal holder until OCT images reach optimal quality. In the x' fast scanning direction, make sure that the cross-sectional B-scan image appears flat. When switching to the y' slow scanning direction, make sure the cross-section B-scan image appears tilted, due to the oblique scanning.
8. Remove the neutral density filter to the blue light excitation and monitor the real time feed from the camera. Cross sectional fluorescent image should appear showing blood vessels appearing in different depths.
   1. Adjust the focus of the final fluorescence imaging system to reach the optimal focus. Allow fine adjustments of the eye position in the lateral plane to reach optimal oSLO image quality.
9. After the alignment, start to acquire simultaneous OCTA and volumetric fluorescein angiography (vFA).
10. Construct the volumetric images for both OCTA and oSLO by Matlab. The algorithms are previously described in detail¹⁰. Generate depth-resolved retinal vasculatures by image segmentation.
11. After completing the imaging, turn off the laser, release the animal and apply some ophthalmic ointment on the eyes, and then place the animal in a recovery box.
12. Do not leave the animal unattended until it has regained sufficient consciousness to maintain sternal recumbency or as per institutional policy.

Wyniki

Figure 4a shows a cross-sectional OCT image of a rat retina. Figure 4b-4c show the same retinal cross-sectional images of OCTA and oSLO vFA acquired at the same time. The oSLO enables cross-sectional FA analogous to the OCT B-scan. In comparison to OCTA, the oSLO vFA cross-sectional image clearly identifies the vessels in nerve fiber layer (NFL) and ganglion cell layer (GCL), and capillaries in outer plexiform la...

Dyskusje

Here, we have described oSLO, an in vivo volumetric fluorescent retinal imaging technique with a FOV over 30°. Compared to OCT, a current standard of care imaging method in ophthalmology, oSLO offers a similar 3D imaging capability yet allows fluorescence contrast that OCT is not sensitive to. The advantage of oSLO is that it requires only one raster scan, and thus allows the seamless combination of OCT, providing two complementary techniques for structural and fluorescent volumetric imaging.

Materiały

Name	Company	Catalog Number	Comments
Supercontinuum Laser Source	NKT Photonics	SuperK EXTREME EXU-OCT6
Dichroic Mirror (DM1)	Thorlabs	DMLP650R
Dichroic Mirror (DM2)	Chroma	ZT514/1064rpc
Dichroic Mirror (DM3)	Thorlabs	DMLP900R
Single Mode Fiber (SMF 1)	Thorlabs	P3-460B-FC-2
Single Mode Fiber (SMF 2)	Thorlabs	P3-780A-FC-2
Optic Fiber Coupler	Thorlabs	TW850R5A2
1:1 Telescope System	Thorlabs	AC254-100-A×2
3:1 Telescope System	Thorlabs	AC254-150-A×2
3:1 Telescope System	Thorlabs	AC254-50-A×2
Galvo Mirrors (GM1,GM2)	Thorlabs	GVS201×2
De-sacn Galvo Mirrors (GM3)	Thorlabs	GVS011
Objective Lens	Olympus	UplanSApo 20×/0.75
Final imaging system	Olympus	UplanFL N 10×/0.3
Final imaging system	Computar	12-36mm/1:2.8
Camera	PCO	Pco.pixelfly usb
Filter	Thorlabs	FEL0800
Mounted Continuously Variable ND Filter	Thorlabs	NDC-50C-4M-A
Line Scan Camera	Thorlabs	SPL2048-140K
Analog Output Board (AO1)	National Instrument	PCI-6731
Analog Output Board (AO2)	National Instrument	PCIe-6351
Long pass filter	Thorlabs	FEL0800