YG is supported by a fellowship from IDB. IN is an Alon fellow and a faculty fellow of the Edmond J&#x202D;. &#x202C;Safra Center for Bioinformatics at Tel Aviv University&#x202D;.&#x202C; This research was supported by ISF grant 1499/10.

1. Creating a Scotch-tape Master5
<ol>
	<li>Draw or print out desired microchannel layout, to scale, on paper. In our case the design consists of two Y-shaped channels, each 3 mm wide (Figure 2).</li>
	<li>Cover a glass-slide with layers of scotch tape. The number of layers will determine the height of the channel (about 60 &mu;m per layer). We used 3 scotch tape layers.</li>
	<li>Place the layout design on a flat surface. Align the slide over the design pattern. Carefully cut the tape on the glass slide with a scalpel according to the layout.</li>
	<li>Remove the Scotch tape from all regions of the glass slide except those in the layout of the microchannel.</li>
	<li>Place the slide in a heating oven at 65 &deg;C for 2-3 min. Clean gently with ethanol.</li>
</ol>
2. Fabricating a PDMS Microfluidic Device
<ol>
	<li>Mix the base and curing components of PDMS as recommended by the manufacturer. We use a 10:1 ratio of base to curing agent. Pour about 30 ml of PDMS mixture into a Petri dish to a height of ~0.5 cm. Degas the PDMS in vacuum if needed. Submerge the glass slide in the PDMS with the patterned Scotch tape facing up. Placing the pattern after the PDMS prevents formation of air bubbles between the slide and dish bottom. Cure for 48 hr at 65 &deg;C, making sure the dish is horizontal using a bubble level.</li>
	<li>In a new 90 mm Petri dish pour 3 ml of PDMS mix, resulting in a layer about 0.5 mm deep. (If a spin coater is available, it can be used for this stage).</li>
	<li>Degas and cure as in 2.1.</li>
	<li>Gently cut out the microfluidic device to the desired size with a scalpel. This layer will be termed the "flow layer".</li>
	<li>Cut out a similarly sized piece of thin layer PDMS from the second Petri dish. This will be termed the "wells layer".</li>
	<li>Use an appropriately sized biopsy puncher (We use 1.2 mm ID) to punch holes for the inlets and outlets in the flow layer.</li>
	<li>Place the wells layer on a thick glass slide over the design layout and punch out wells, using 2 mm ID biopsy puncher, in alignment with the microchannels on the layout.</li>
	<li>Clean both PDMS layers as well as a 24 mm x 60 mm glass coverslip with ethanol. Air-dry and keep clean.</li>
	<li>Plasma treat both the glass coverslip and the wells layer PDMS using either standard plasma etcher (for non-reversible bonding) or a hand-held corona treater6 for reversible bonding. Carefully place the wells layer on top of the coverslip to cause adhesion (Figure 3). Gently rub out any air bubbles (if needed).</li>
</ol>
3. Cell Imaging Experiment
<ol>
	<li>Make sure you have the desired media ready in appropriate syringes connected to flexible plastic tubes with internal diameter of 0.02" (Tygon) in the syringe pump.</li>
	<li>Grow S. cerevisiae strains to the desired phase in liquid YPD. Vortex thoroughly and place 300 &mu;l of each strain into a microcentrifuge tube.</li>
	<li>Gently place 1 &mu;l of Concanavalin A (sigma) 2 mg/ml into each well. Wash out excess Concanavalin A from each well twice by gently pipetting water.</li>
	<li>While the Concanavalin A is drying, wash strains twice with 300 &mu;l of SC medium lacking glucose. Washing residual glucose from the cell walls helps proper adherence to the Concanavalin A.</li>
	<li>Vortex cells thoroughly. Pipette 0.75 &mu;l or less of each cell suspension into its own well (Figure 3). Gently wash out residual cells with rich medium. The next two steps need to be performed quickly in order to prevent cells from drying up.</li>
	<li>Plasma treat the chip and the wells thoroughly using the hand-held corona treater, being careful not to hit the wells directly. Carefully place the chip on the wells, paying close attention to the alignment between the two (this step can be done under a stereoscope). Gently press to adhere the two layers of PDMS. Slowly fill the device completely with about 50 &mu;l rich medium, making sure no air bubbles are left inside the channel.</li>
	<li>Connect the device, inserting the tubes into the appropriate inlets and start media flow. Take care that no air bubbles are introduced into the device as these can be tricky to remove; this can be accomplished by disconnecting an inlet or outlet and gently tapping on the device where the bubbles are, being careful not to break the glass coverslip.</li>
	<li>Place under microscope and find appropriate imaging points in each well.</li>
	<li>Keep the cells under rich medium flow for 1 hr or longer to allow recovery if needed.</li>
	<li>Start the experiment: we use constant flow from each of the two syringe pumps to prevent backflow of the media, changing relative flow rates as desired. Setting pump A to 0.8 ml/hr and pump B to 0.2 ml/hr results in medium A flowing over 80% of the width of the channel (Figure 4). This can be dynamically changed by changing the two flow rates. The new conditions stabilize within seconds along the full length of the channel2.</li>
</ol>

<ol>
	<li>Dertinger, S. K., Jiang, X., Li, Z., Murthy, V. N., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Gradients+of+substrate-bound+laminin+orient+axonal+specification+of+neurons.">Gradients of substrate-bound laminin orient axonal specification of neurons.</a> Proceedings of the National Academy of Sciences of the United States of America. 99, 12542-12547 (2002).</li><li>Hersen, P., McClean, M. N., Mahadevan, L., Ramanathan, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Signal+processing+by+the+HOG+MAP+kinase+pathway.">Signal processing by the HOG MAP kinase pathway.</a> Proc. Natl. Acad. Sci. U.S.A. 105, 7165-7170 (2008).</li><li>Paliwal, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=MAPK-mediated+bimodal+gene+expression+and+adaptive+gradient+sensing+in+yeast.">MAPK-mediated bimodal gene expression and adaptive gradient sensing in yeast.</a> Nature. 446, 46-51 (2007).</li><li>Bennett, M. R., Hasty, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+devices+for+measuring+gene+network+dynamics+in+single+cells.">Microfluidic devices for measuring gene network dynamics in single cells.</a> Nat. Rev. Genet. 10, 628-638 (2009).</li><li>Shrirao, A. B., Perez-Castillejos, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simple+Fabrication+of+Microfluidic+Devices+by+Replicating+Scotch-tape+Masters.">Simple Fabrication of Microfluidic Devices by Replicating Scotch-tape Masters.</a> Chips &#38; Tips. , (2010).</li><li>Haubert, K., Drier, T., Beebe, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=PDMS+bonding+by+means+of+a+portable,+low-cost+corona+system.">PDMS bonding by means of a portable, low-cost corona system.</a> Lab Chip. 6, 1548-1549 (2006).</li><li>Gerber, D., Maerkl, S. J., Quake, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+in+vitro+microfluidic+approach+to+generating+protein-interaction+networks.">An in vitro microfluidic approach to generating protein-interaction networks.</a> Nat. Methods. 6, 71-74 (2009).</li></ol>

No conflicts of interest declared.

In this paper we present a simple benchtop method for creating a microfluidic device that allows following several yeast strains simultaneously under dynamic conditions. Following several strains in one channel provides a reliable tool for comparing dynamics of single cell responses in multiple strains. One advantage of our approach is the ability to fabricate the device with simple techniques without the need for a clean room. In fact, we have also carried out the protocol skipping the plasma treatment operations (in st...

Cells are constantly reacting to a dynamically changing environment, by changing their metabolism, transcriptional profile and cellular functions. To study these phenomena, methods that can quantify such changes are needed. One type of readout for such responses is the change in localization of stress related transcription factors in response to nutritional stress.
Microfluidic devices1 have been used to dynamically manipulate environmental conditions to cells2-4. They present several advantages for live cell imaging: the environment of the cells can be precisely controlled and dynamically changed; cells can be live-imaged at all times, including during manipulation of external conditions; and minimal reagent volumes are required. A very simple design for a microfluidic device, allowing alternation between two conditions, is a Y-shaped device2. We routinely use Y-shaped microfluidic devices that allow application of dynamic changes to the cells in the channel. We use this device to follow localization changes of fluorescently tagged stress related transcription factors in yeast cells. We follow these changes under changing nutritional conditions. For example, we can provide a pulse (or series of pulses) of glucose-containing medium within a period of no-glucose medium, at a very fine temporal resolution. Often in such experiments, one is interested in comparing the responses of different cell strains (for example, different mutants, or different wild isolates). The Y-shaped channel is limited to one strain in each channel - if more than one strain is used, there is no simple way to distinguish between the strains. To overcome this, different channels can be used. If we want to apply the same dynamics conditions to multiple strains, we would like to combine the Y-channel concept with multiple channels. There are two challenges in implementing this solution: It can be hard to apply the same conditions at the same time to all channels, and there is a geometric limitation to the number of Y-channels that can be fitted in one device. We were therefore looking for a way for viewing several strains in one channel under dynamic conditions.
Here we describe a two-layered microfluidic device intended for imaging multiple strains in one channel under the same dynamic conditions. The bottom layer consists of thin PDMS with a row of holes. This layer is attached to the glass coverslip creating wells into which we will place the different strains, adhering them with Concanavalin A to the glass. The second layer is a Y-shaped microfluidic device created using the scotch tape method5. After placing the strains in the wells the second layer is quickly aligned and attached to the first one, creating one channel with several wells that contain the different strains. This final device allows following several strains in one channel, where all strains are subjected to the same conditions at the exact same time. The whole design and production process can be done on the benchtop, using simple means, with no soft lithography.

<table><tbody><tr><td>PDMS- SYLGARD 184</td><td>Dow Corning USA</td><td></td><td></td></tr><tr><td>Vacuum desiccator</td><td>Nalgene</td><td>5310-0250</td><td></td></tr><tr><td>Biopsy punchers</td><td>Ted Pella Inc.</td><td>Harris Uni-Core 15076 (2 mm), 15074 (1.2 mm)</td><td></td></tr><tr><td>Syringe pumps</td><td>Chemyx</td><td>Fusion 200</td><td></td></tr><tr><td>Corona treater</td><td>Electro-technic products</td><td>BD-20</td><td></td></tr><tr><td>Tygon tubing</td><td>Tygon</td><td>S-54-HL</td><td></td></tr><tr><td>Concanavalin-A</td><td>Sigma</td><td>C7275</td><td></td></tr><tr><td>Scotch tape</td><td>3M Scotch</td><td>Transparent Tape 1/2&quot;</td><td></td></tr></tbody></table>

a microfluidic device for studying multiple distinct strains

The study of cell responses to environmental changes poses many experimental challenges: cells need to be imaged under changing conditions, often in a comparative manner. Multiwell plates are routinely used to compare many different strains or cell lines, but allow limited control over the environment dynamics. Microfluidic devices, on the other hand, allow exquisite dynamic control over the surrounding conditions, but it is challenging to image and distinguish more than a few strains in them. Here we describe a method to easily and rapidly manufacture a microfluidic device capable of applying dynamically changing conditions to multiple distinct yeast strains in one channel. The device is designed and manufactured by simple means without the need for soft lithography. It is composed of a Y-shaped flow channel attached to a second layer harboring microwells. The strains are placed in separate microwells, and imaged under the exact same dynamic conditions. We demonstrate the use of the device for measuring protein localization responses to pulses of nutrient changes in different yeast strains.

To demonstrate the separation between different strains we imaged two distinguishable yeast strains in alternate wells. Imaging the full wells shows no cell leakage between wells (Figure 5a,b). Both strains have the transcription factor MSN2 tagged with YFP. To test the simultaneous effect of dynamically changing conditions, we switched the flow rates in the two input channels, creating a step of no-glucose medium, which resulted in localization of Msn2-YFP to the nucleus (Figure 5c,d). ...

Watch this Scientific Journal Video about A Microfluidic Device for Studying Multiple Distinct Strains at JoVE.com

A Microfluidic Device for Studying Multiple Distinct Strains

We present a simple method to produce microfluidic devices capable of applying similar dynamic conditions to multiple distinct strains, without the need for a clean room or soft lithography.

The study of cell responses to environmental changes poses many experimental challenges: cells need to be imaged under changing conditions, often in a ...

a-microfluidic-device-for-studying-multiple-distinct-strains

Research

JoVE Journal

Bioengineering

8.7K Views.  Tel Aviv University. We present a simple method to produce microfluidic devices capable of applying similar dynamic conditions to multiple distinct strains, without the need for a clean room or soft lithography.

Video: A Microfluidic Device for Studying Multiple Distinct Strains

Microfluidic Chips Controlled with Elastomeric Microvalve Arrays

Miniaturized microfluidic systems provide simple and effective solutions for low-cost point-of-care diagnostics and high-throughput biomedical assays. Robust flow control and precise fluidic volumes are two critical requirements for these applications. We have developed microfluidic chips featuring elastomeric polydimethylsiloxane (PDMS) microvalve arrays that: 1) need no extra energy source to close the fluidic path, hence the loaded device is highly portable; and 2) allow for microfabricating deep (up to 1 mm) channels with vertical sidewalls and resulting in very precise features.

The PDMS microvalves-based devices consist of three layers: a fluidic layer containing fluidic paths and microchambers of various sizes, a control layer containing the microchannels necessary to actuate the fluidic path with microvalves, and a middle thin PDMS membrane that is bound to the control layer. Fluidic layer and control layers are made by replica molding of PDMS from SU-8 photoresist masters, and the thin PDMS membrane is made by spinning PDMS at specified heights. The control layer is bonded to the thin PDMS membrane after oxygen activation of both, and then assembled with the fluidic layer. The microvalves are closed at rest and can be opened by applying negative pressure (e.g., house vacuum). Microvalve closure and opening are automated via solenoid valves controlled by computer software.

Here, we demonstrate two microvalve-based microfluidic chips for two different applications. The first chip allows for storing and mixing precise sub-nanoliter volumes of aqueous solutions at various mixing ratios. The second chip allows for computer-controlled perfusion of microfluidic cell cultures.

The devices are easy to fabricate and simple to control. Due to the biocompatibility of PDMS, these microchips could have broad applications in miniaturized diagnostic assays as well as basic cell biology studies.

We demonstrate protocols for manufacturing and automating elastomeric polydimethylsiloxane (PDMS)-based microvalve arrays that need no extra energy to close and feature photolithographically defined precise volumes. A parallel subnanoliter-volume mixer and an integrated microfluidic perfusion system are presented.

Miniaturized microfluidic systems provide simple and effective solutions for low-cost point-of-care diagnostics and high-throughput biomedical assays.  ...

Biology

Microfluidic Picoliter Bioreactor for Microbial Single-cell Analysis: Fabrication, System Setup, and Operation

In this protocol the fabrication, experimental setup and basic operation of the recently introduced microfluidic picoliter bioreactor (PLBR) is described in detail. The PLBR can be utilized for the analysis of single bacteria and microcolonies to investigate biotechnological and microbiological related questions concerning, e.g.&#160;cell growth, morphology, stress response, and metabolite or protein production on single-cell level. The device features continuous media flow enabling constant environmental conditions for perturbation studies, but in addition allows fast medium changes as well as oscillating conditions to mimic any desired environmental situation. To fabricate the single use devices, a silicon wafer containing sub micrometer sized SU-8 structures served as the replication mold for rapid polydimethylsiloxane casting. Chips were cut, assembled, connected, and set up onto a high resolution and fully automated microscope suited for time-lapse imaging, a powerful tool for spatio-temporal cell analysis. Here, the biotechnological platform organism Corynebacterium glutamicum&#160;was seeded into the PLBR and cell growth and intracellular fluorescence were followed over several hours unraveling time dependent population heterogeneity on single-cell level, not possible with conventional analysis methods such as flow cytometry. Besides insights into device fabrication, furthermore, the preparation of the preculture, loading, trapping of bacteria, and the PLBR cultivation of single cells and colonies is demonstrated. These devices will add a new dimension in microbiological research to analyze time dependent phenomena of single bacteria under tight environmental control. Due to the simple and relatively short fabrication process the technology can be easily adapted at any microfluidics lab and simply tailored towards specific needs.

In this protocol the fabrication, setup and basic operation of a microfluidic picoliter bioreactor (PLBR) for single-cell analysis of prokaryotic microorganisms is introduced. Industrially relevant microorganisms were analyzed as proof of principle allowing insights into growth rate, morphology, and phenotypic heterogeneity over certain time periods, hardly possible with conventional methods.

In this protocol the fabrication, experimental setup and basic operation of the recently introduced microfluidic picoliter bioreactor (PLBR) is described ...

A Microfluidic Chip for the Versatile Chemical Analysis of Single Cells

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this purpose, the cells are passively trapped in the middle of a microchamber. Upon activation of the control layer, the cell is isolated from the surrounding volume in a small chamber. The surrounding volume can then be exchanged without affecting the isolated cell. However, upon short opening and closing of the chamber, the solution in the chamber can be replaced within a few hundred milliseconds. Due to the reversibility of the chambers, the cells can be exposed to different solutions sequentially in a highly controllable fashion, e.g. for incubation, washing, and finally, cell lysis. The tightly sealed microchambers enable the retention of the lysate, minimize and control the dilution after cell lysis. Since lysis and analysis occur at the same location, high sensitivity is retained because no further dilution or loss of the analytes occurs during transport. The microchamber design therefore enables the reliable and reproducible analysis of very small copy numbers of intracellular molecules (attomoles, zeptomoles) released from individual cells. Furthermore, many microchambers can be arranged in an array format, allowing the analysis of many cells at once, given that suitable optical instruments are used for monitoring. We have already used the platform for proof-of-concept studies to analyze intracellular proteins, enzymes, cofactors and second messengers in either relative or absolute quantifiable manner.

In this article we present a microfluidic chip for single cell analysis. It allows the quantification of intracellular proteins, enzymes, cofactors, and second messengers by means of fluorescent assays or immunoassays.&#160;

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this ...

A Microfluidic Platform for Precision Small-volume Sample Processing and Its Use to Size Separate Biological Particles with an Acoustic Microdevice

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. However, to achieve robust sample manipulation it is necessary to address device integration with the macroscale environment. To realize repeatable, sensitive particle separation with microfluidic devices, this protocol presents a complete automated and integrated microfluidic platform that enables precise processing of 0.15&#8211;1.5 ml samples using microfluidic devices. Important aspects of this system include modular device layout and robust fixtures resulting in reliable and flexible world to chip connections, and fully-automated fluid handling which accomplishes closed-loop sample collection, system cleaning and priming steps to ensure repeatable operation. Different microfluidic devices can be used interchangeably with this architecture. Here we incorporate an acoustofluidic device, detail its characterization, performance optimization, and demonstrate its use for size-separation of biological samples. By using real-time feedback during separation experiments, sample collection is optimized to conserve and concentrate sample. Although requiring the integration of multiple pieces of equipment, advantages of this architecture include the ability to process unknown samples with no additional system optimization, ease of device replacement, and precise, robust sample processing.

This protocol describes a system architecture for performing automated small volume (0.15&#8211;1.5 ml) particle separations using a microfluidic device, and discusses methods to optimize acoustofluidic device performance and operation.

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. ...

A Microfluidic Platform for High-throughput Single-cell Isolation and Culture

Studying the heterogeneity of single cells is crucial for many biological questions, but is technically difficult. Thus, there is a need for a simple, yet high-throughput, method to perform single-cell culture experiments. Here, we report a microfluidic chip-based strategy for high-efficiency single-cell isolation (~77%) and demonstrate its capability of performing long-term single-cell culture (up to 7 d) and cellular heterogeneity analysis using clonogenic assay. These applications were demonstrated with KT98 mouse neural stem cells, and A549 and MDA-MB-435 human cancer cells. High single-cell isolation efficiency and long-term culture capability are achieved by using different sizes of microwells on the top and bottom of the microfluidic channel. The small microwell array is designed for precisely isolating single-cells, and the large microwell array is used for single-cell clonal culture in the microfluidic chip. This microfluidic platform constitutes an attractive approach for single-cell culture applications, due to its flexibility of adjustable cell culture spaces for different culture strategies, without decreasing isolation efficiency.

Here, we present a protocol for isolating and culturing single cells with a microfluidic platform, which utilizes a new microwell design concept to allow for high-efficiency single cell isolation and long-term clonal culture.

Studying the heterogeneity of single cells is crucial for many biological questions, but is technically difficult. Thus, there is a need for a simple, yet ...

An Ultrahigh-throughput Microfluidic Platform for Single-cell Genome Sequencing

Sequencing technologies have undergone a paradigm shift from bulk to single-cell resolution in response to an evolving understanding of the role of cellular heterogeneity in biological systems. However, single-cell sequencing of large populations has been hampered by limitations in processing genomes for sequencing. In this paper, we describe a method for single-cell genome sequencing (SiC-seq) which uses droplet microfluidics to isolate, amplify, and barcode the genomes of single cells. Cell encapsulation in microgels allows the compartmentalized purification and tagmentation of DNA, while a microfluidic merger efficiently pairs each genome with a unique single-cell oligonucleotide barcode, allowing &gt;50,000 single cells to be sequenced per run. The sequencing data is demultiplexed by barcode, generating groups of reads originating from single cells. As a high-throughput and low-bias method of single-cell sequencing, SiC-seq will enable a broader range of genomic studies targeted at diverse cell populations.

Single-cell sequencing reveals genotypic heterogeneity in biological systems, but current technologies lack the throughput necessary for the deep profiling of community composition and function. Here, we describe a microfluidic workflow for sequencing &gt;50,000 single-cell genomes from diverse cell populations.

Sequencing technologies have undergone a paradigm shift from bulk to single-cell resolution in response to an evolving understanding of the role of ...

Establishing Single-Cell Based Co-Cultures in a Deterministic Manner with a Microfluidic Chip

Cell co-culture assays have been widely used for studying cell-cell interactions between different cell types to better understand the biology of diseases including cancer. However, it is challenging to clarify the complex mechanism of intercellular interactions in highly heterogeneous cell populations using conventional co-culture systems because the heterogeneity of the cell subpopulation is obscured by the average values; the conventional co-culture systems can only be used to describe the population signal, but are incapable of tracking individual cells behavior. Furthermore, conventional single-cell experimental methods have low efficiency in cell manipulation because of the Poisson distribution. Microfabricated devices are an emerging technology for single-cell studies because they can accurately manipulate single cells at high-throughput and can reduce sample and reagent consumption. Here, we describe the concept and application of a microfluidic chip for multiple single-cell co-cultures. The chip can efficiently capture multiple types of single cells in a culture chamber (~46%) and has a sufficient culture space useful to study the cells&#39; behavior (e.g., migration, proliferation, etc.) under cell-cell interaction at the single-cell level. Lymphatic endothelial cells and oral squamous cell carcinoma were used to perform a single-cell co-culture experiment on the microfluidic platform for live multiple single-cell interaction studies.

This report describes a microfluidic chip-based method to set up a single cell culture experiment in which high-efficiency pairing and microscopic analysis of multiple single cells can be achieved.

Cell co-culture assays have been widely used for studying cell-cell interactions between different cell types to better understand the biology of diseases ...

Generation of Dynamical Environmental Conditions using a High-Throughput Microfluidic Device

Mimicking in vivo environmental conditions is crucial for in vitro studies on complex life machinery. However, current techniques targeting live cells and organs are either highly expensive, like robotics, or lack nanoliter volume and millisecond time accuracy in liquid manipulation. We herein present the design and fabrication of a microfluidic system, which consists of 1,500 culture units, an array of enhanced peristaltic pumps and an on-site mixing modulus. To demonstrate the capacities of the microfluidic device, neural stem cell (NSC) spheres are maintained in the proposed system. We observed that when the NSC sphere is exposed to CXCL in day 1 and EGF in day 2, the round-shaped conformation is well maintained. Variation in the input order of 6 drugs causes morphological changes to the NSC sphere and the expression level representative marker for NSC stemness (i.e., Hes5 and Dcx). These results indicate that dynamic and complex environmental conditions have great effects on NSC differentiation and self-renewal, and the proposed microfluidic device is a suitable platform for high throughput studies on the complex life machinery.

We present a microfluidic system for high throughput studies on complex life machinery, which consists of 1500 culture units, an array of enhanced peristaltic pumps and an on-site mixing modulus. The microfluidic chip allows for the analysis of the highly complex and dynamic micro-environmental conditions in vivo.

Mimicking in vivo environmental conditions is crucial for in vitro studies on complex life machinery. However, current techniques targeting live cells and ...

Microfluidic Tools for Probing Fungal-Microbial Interactions at the Cellular Level

Filamentous fungi are successful inhabitants of soil and play a major role in soil ecosystems, such as in the decomposition of organic and inorganic matter, as well as regulation of nutrient levels. There they also find numerous opportunities to interact with a variety of other microbes such as bacteria or other fungi. Studying fungal interactions at the cellular level, however, can be challenging owing to the black box-like nature of soil. New microfluidic tools are being developed for the study of fungal interactions; two platforms designed to study bacterial-fungal and fungal-fungal interactions are highlighted. Within these microchannels, fungal-microbial interactions can be monitored in controlled physico-chemical environments at higher temporal and spatial resolution than previously possible. Application of these tools have yielded numerous novel biological insights, such as the observation of bacterial polar attachment to hyphae or revealing uncharacterised fungal-fungal antagonisms. A key feature of these methodologies regards the ease of use of this tool by non-experts, yielding highly translatable technologies for use in microbiology labs.

Owing to the opacity of soil, interactions between its constituent microbes cannot easily be visualised with cellular resolution. Here, two microfluidic tools are presented, which offer new opportunities for investigating fungal-microbial interactions. The devices are versatile and simple to use, enabling high spatiotemporal control and high-resolution imaging at the cellular level.

Filamentous fungi are successful inhabitants of soil and play a major role in soil ecosystems, such as in the decomposition of organic and inorganic ...

Microfluidic Droplet Assay for Single-Cell Cytokine Secretion Analysis

Microfluidic Approach to Resolve Simultaneous and Sequential Cytokine Secretion of Individual Polyfunctional Cells

Infections, autoimmune diseases, desired and adverse immunological responses to treatment can lead to a complex and dynamic cytokine response in vivo. This response involves numerous immune cells secreting various cytokines to orchestrate the immune reaction. However, the secretion dynamics, amounts, and co-occurrence of the different cytokines by various cell subtypes remain poorly understood due to a lack of appropriate tools to study them. Here, we describe a protocol using a microfluidic droplet platform that allows the time-resolved quantitative measurement of secretion dynamics for several cytokines in parallel on the single-cell level. This is enabled by the encapsulation of individual cells into microfluidic droplets together with a multiplexed immunoassay for parallel quantification of cytokine concentrations, their immobilization for dynamic fluorescent imaging, and the analysis of the respective images to derive secreted quantities and dynamics. The protocol describes the preparation of functionalized magnetic nanoparticles, calibration experiments, cell preparation, and the encapsulation of the cells and nanoparticles into droplets for fluorescent imaging and subsequent image and data analysis using the example of lipopolysaccharide-stimulated human peripheral blood mononuclear cells. The presented platform identified distinct cytokine secretion behavior for single and co-secreting cells, characterizing the expected phenotypic heterogeneity in the measured cell sample. Furthermore, the modular nature of the assay allows its adaptation and application to study a variety of proteins, cytokines, and cell samples, potentially leading to a deeper understanding of the interplay between different immune cell types and the role of the different cytokines secreted dynamically to shape the tightly regulated immune response. These new insights could be particularly interesting in the studies of immune dysregulations or in identifying target populations in therapy and drug development.

Author Spotlight: Unveiling the Polyfunctionality and Heterogeneity in Immune Responses

The protocol describes an advanced microfluidic platform to quantitatively measure cytokine secretion dynamics of individual human peripheral blood mononuclear cells. The platform measures up to three cytokines in parallel (IL-6, TNF&#945;, and IL-1&#946;) for each individual cell stimulated with lipopolysaccharide as an example.

Infections, autoimmune diseases, desired and adverse immunological responses to treatment can lead to a complex and dynamic cytokine response in vivo. ...