A técnica de pressão polimento foi desenvolvido em colaboração com Lockery SR.

Pipetas puxando Usando um filamento como um extrator Sutter P-97 Flaming Puller microeletrodos / Brown, puxe um conjunto de aproximadamente 10-20 pipetas. <ol><li> Selecione seu vidro. Usamos borosilicato (BF150-86-10, OD = 1,5 mm, ID = 0,86 mm). Armazenar o vidro com cuidado para que ele permaneça limpo e livre de poeira. </li><li> Conceber um programa de puxar. O principal objetivo é uma dica de abertura aproximadamente o tamanho desejado, que dependerá da aplicação. P-97 Sutter Cookbook Pipetar 2 é uma excelente referência. </li><li> Observe o seu pipetas sob um microscópio para determinar o diâmetro de abertura e suavidade. Descartar áspera, dicas irregular, ou irregular. Para a gravação normal patch-clamp, uma abertura que é de 2-4 mM todo é melhor. A ponta romba leva a menor resistência para o diâmetro mesma abertura, que é o preferido. Forma e tamanho pode ser modificado durante o polimento, abaixo. </li></ol> Polimento pipetas pressão <ol><li> Anexar um suporte para uma pipeta, comprimido limpo linha de ar. Usando um regulador, definir a linha de ar comprimido a pressão para ~ 40 PSI. Conecte a linha de ar comprimido para uma válvula de controle de 4 vias que permitirá que a pressão titular pipeta a ser ligado e desligado. Conectar um titular pipeta para a válvula de controle com um comprimento de ⅛ em Tygon ® tubulação. </li><li> Use um equipamento de polimento (microforge) com um suporte de pipeta de alta pressão, uma bobina de polimento controlada por um pé-pedal, um microscópio equipado com uma ampliação baixa e alta, longa distância de trabalho (idealmente, 10x e 100x) ar objetivos. É fundamental ser capaz de observar a abertura da pipeta durante o protocolo. </li><li> Opcional: Brasão da pipeta com um isolador hidrofóbicos para diminuir a capacitância e melhorar as características de ruído (consulte &quot;pipetas Puxando&quot; para esta técnica). </li><li> Verifique se a válvula de pressão está na posição off. Coloque uma pipeta no suporte de pipetas e aperte o encaixe para os dedos. Nota de segurança: Se a pipeta é mantido firmemente no suporte pipeta, a pressão do ar fará com que a pipeta para ser ejetado do titular da pipeta. </li><li> Coloque a pipeta e titular no microforge. Titular posição da pipeta para o palco microscópio para que tanto a ponta da bobina e polimento são visíveis em potência (10x) baixa na microforge. Traga a ponta ~ 75 microns do filamento. Tenha em mente que o filamento se expande quando aquecida. </li><li> Mude para a alta potência objetivas (100x). Tanto a ponta da pipeta e da bobina de polimento deve estar em foco e no campo de visão. Se não, ajuste a altura da bobina de polimento. (Posição A pipeta não pode ser ajustado). A ponta da pipeta e bobina de polimento deve ser perto de lados opostos do campo de visão. Evite posicionar a bobina muito perto da ponta da pipeta porque vai expandir, uma vez que aquece e chocar-se com a pipeta. </li><li> Gire a válvula para direcionar o ar pressurizado para a pipeta, e aquecer a ponta da pipeta até o cone atrás da ponta começa a balão para fora. </li><li> Parar o aquecimento antes da ponta balões também extensivamente. A experimentação é necessária para determinar a distância apropriada, calor e tempo para a forma desejada. </li><li> Opcional: Reduza o diâmetro de abertura ponta a ponta por polimento, na ausência de pressão. As etapas 7 e 8 pode repetir para ajustar tanto a forma e as dimensões da ponta da pipeta. </li><li> Desligue a pressão e ao mesmo tempo apontando a ponta da pipeta para uma direção segura, retire a pipeta e colocá-lo em uma caixa de armazenamento limpa onde será protegido de poeira. Nota de segurança: Se a pressão do ar não é desligado, a pipeta pode ser expulso do titular pipeta durante a remoção. </li></ol> Notas sobre a microforge Nós usamos um microforge montado a partir de off-the-shelf componentes disponíveis comercialmente. (Você também pode comprar um kit de pressão de polimento de algumas empresas, por exemplo, ALA Ciência, GlassWorx). Independentemente do microforge, é essencial ter ótica que são bons o suficiente para ver a abertura da ponta, que é muitas vezes apenas alguns mM de diâmetro. Nós usamos uma lente de longa distância de trabalho 100x para esta finalidade. Além disso, o revestimento da bobina polimento com alta temperatura de fusão de vidro, a fim de minimizar a deposição de metal vaporizado sobre as pipetas. Parte 3: Resultados Previstos Polimento pressão moderada pode reduzir a resistência de uma pipeta sem uma alteração significativa na abertura de diâmetro. Se desejar, este protocolo pode ser usado para fazer pipetas com sub-micron aberturas e resistências entre 5-10MΩ.

<ol>
	<li>Goodman, M. B., Lockery, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Pressure+polishing:+a+method+for+re-shaping+patch+pipettes+during+fire+polishing. .">Pressure polishing: a method for re-shaping patch pipettes during fire polishing. .</a> J Neurosci Methods. 100, 13-15 (2000).</li></ol>

Nós originalmente desenvolvido este método para fazer pipetas útil para patch-clamp gravação 2-3 neurônios M em C. elegans 1. Ele está em uso rotineiro no laboratório Goodman. Nós pipetas pressão polonês não só para a gravação de pequenos C. neurônios elegans, mas também para a obtenção de macropatch e single-channel gravações de canais iônicos expressos em oócitos Xenopus. Para um determinado diâmetro da ponta-abertura, a forma contundente produz uma pipeta de menor resistência...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Glass Capillaries</td>
<td>Consumable</td>
<td>Sutter Instruments</td>
<td>BF150-85-10 (or similar)</td>
<td>The method works with any type of capillary except those made from quartz. However, we recommend using capillaries with a filament.</td>
</tr>
<tr>
<td>Inverted Microscope</td>
<td>Microscope</td>
<td>Leica</td>
<td>DM IL (or similar)</td>
<td>Any simple inverted microscope will do. However, it is essential to have sufficient magnification to see pipettes during polishing. We use a 100x metallurgical lens with a long working distance for this purpose.</td>
</tr>
<tr>
<td>Microforge Kit</td>
<td>Tool</td>
<td>ALA Science</td>
<td>CPM-2</td>
<td>Supplies polishing coil, controller and foot pedal.</td>
</tr>
<tr>
<td>Air pressure source</td>
<td>Tool</td>
<td>ALA Science</td>
<td>PR-60</td>
<td>Accessory for providing high pressure, includes a suitable valve. Alternatively, compressed air from the building can be used together with a filter/regulator (set to 40 PSI) and a 4-way valve (see below)</td>
</tr>
<tr>
<td>4-way valve</td>
<td>Tool</td>
<td>Cole-Parmer</td>
<td>A-98150-01</td>
<td>Fittings will be needed to couple valve to tubing</td>
</tr>
<tr>
<td>Pipette Holder with Luer Connector</td>
<td>Tool</td>
<td>World Precision Instruments</td>
<td>MPH-6S20</td>
<td>Use a male luer-to-barb fitting to connect pipette holder to high-pressure tubing</td>
</tr>
<tr>
<td>Tygon&#174; tubing</td>
<td>Tool</td>
<td>Cole-Parmer</td>
<td>06408-62</td>
<td>Use this tubing to connect pipette holder to 4-way valve
</td>
</tr>		</tbody>
		</table>
		</div>

pressure-polishing pipettes for improved patch-clamp recording

Pressão polimento é um método para moldar pipetas de vidro para patch-clamp gravação. Nós desenvolvido pela primeira vez este método para a fabricação de pipetas adequado para a gravação de pequenos (&lt;3 m) corpos celulares neuronais. O princípio básico é semelhante ao vidro soprado e combina a pressão do ar e calor para modificar a forma de pipetas de patch preparado por um puxador de micropipeta convencionais. Ela pode ser aplicada aos chamados moles (soda de limão) e rígido (borosilicato) óculos. Polimento de pressão de modo geral, pode reduzir a resistência da pipeta em 25%, sem diminuir o diâmetro de uma abertura (Goodman e Lockery, 2000). Pode ser aplicada a praticamente qualquer tipo de vidro e requer apenas a adição de uma válvula de alta pressão e encaixe a um microforge. Esta técnica é essencial para a gravação a partir de células ultrasmall (&lt;5 m) e também pode melhorar a gravação de um único canal, minimizando a resistência da pipeta. A forma nua e crua é também útil para perfurada-patch clamp gravação uma vez que este resultados ponta forma em uma bolha maior membrana disponíveis para a perfuração.

Watch this Scientific Journal Video about Pressure-polishing Pipettes for Improved Patch-clamp Recording at JoVE.com

Pressure-polishing Pipettes for Improved Patch-clamp Recording

Este é um guia para modificar a forma de micropipetas de vidro. Especificamente, usando calor e pressão de ar do cone é alargado, sem aumentar a abertura da ponta, levando a menor resistência da pipeta. Isto é fundamental para obter gravações de baixo ruído de pequenas células, mas é útil em muitas aplicações.

Pressão polimento Pipetas para Gravação de patch-clamp melhorada

Pressure-polishing is a method for shaping glass pipettes for patch-clamp recording.  We first developed this method for fabricating pipettes suitable for ...

pressure-polishing-pipettes-for-improved-patch-clamp-recording

Research

JoVE Journal

Biology

12.9K visualizações.  Stanford University School of Medicine. Este é um guia para modificar a forma de micropipetas de vidro. Especificamente, usando calor e pressão de ar do cone é alargado, sem aumentar a abertura da ponta, levando a menor resistência da pipeta. Isto é fundamental para obter gravações de baixo ruído de pequenas células, mas é útil em muitas aplicações.

Vídeo: Pressure-polishing Pipettes for Improved Patch-clamp Recording

Methods for Patch Clamp Capacitance Recordings from the Calyx

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. Electrical recordings from the presynaptic terminal allow the measurement of action potentials, calcium channel currents, vesicle fusion (exocytosis) and subsequent membrane uptake (endocytosis). The fusion of vesicles containing neurotransmitter causes the vesicle membrane to be added to the cell membrane of the calyx. This increase in the amount of cell membrane is measured as an increase in capacitance. The subsequent reduction in capacitance indicates endocytosis, the process of membrane uptake or removal from the calyx membrane. Endocytosis, is necessary to maintain the structure of the calyx and it is also necessary to form vesicles that will be filled with neurotransmitter for future exocytosis events. Capacitance recordings at the calyx of Held have made it possible to directly and rapidly measure vesicular release and subsequent endocytosis in a mammalian CNS nerve terminal. In addition, the corresponding postsynaptic activity can be simultaneously measured by using paired recordings. Thus a complete picture of the presynaptic and postsynaptic electrical activity at a central nervous system synapse is achievable using this preparation. Here, the methods for slice preparation, morphological features for identification of calyces of Held, basic patch clamping techniques, and examples of capacitance recordings to measure exocytosis and endocytosis are presented.

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal.

Métodos para Recordings patch-clamp Capacitância da Calyx

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. ...

Biologia

Patch Clamp Recording of Ion Channels Expressed in  Xenopus Oocytes

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological measurement of single or multiple ion channels in cells. This technique can be applied to ion channels in both their native environment and expressed in heterologous cells, such as oocytes harvested from the African clawed frog, Xenopus laevis. Here, we describe the well-established technique of patch clamp recording from Xenopus oocytes. This technique is used to measure the properties of expressed ion channels either in populations (macropatch) or individually (single-channel recording). We focus on techniques to maximize the quality of oocyte preparation and seal generation. With all factors optimized, this technique gives a probability of successful seal generation over 90 percent. The process may be optimized differently by every researcher based on the factors he or she finds most important, and we present the approach that have lead to the greatest success in our hands.

This is intended as an introduction to patch clamp recording from Xenopus laevis oocytes. It covers vitelline membrane removal, formation of a gigaohm seal (gigaseal), and the optional conversion of the patch to the outside-out topology.

Gravação de patch-clamp de canais iônicos Expresso em Oócitos Xenopus

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological ...

Making Patch-pipettes and Sharp Electrodes with a Programmable Puller

Glass microelectrodes (also called pipettes) have been a workhorse of electrophysiology for decades. Today, such pipettes are made from glass capillaries using a programmable puller. Such instruments heat the capillary using either a metal filament or a laser and draw out the glass using gravity, a motor or both. Pipettes for patch-clamp recording are formed using only heat and gravity, while sharp electrodes for intracellular recording use a combination of heat, gravity, and a motor. The procedure used to make intracellular recording pipettes is similar to that used to make injection needles for a variety of applications, including cRNA injection into Xenopus oocytes. In general, capillary glass &lt;1.2 mm in diameter is used to make pipettes for patch clamp recording, while narrower glass is used for intracellular recording (outer diameter = 1.0 mm). For each tool, the puller is programmed slightly differently. This video shows how to make both kinds of recording pipettes using pre-established puller programs.

This video shows how to use a programmable puller to make patch pipettes and sharp electrodes for electrophysiology. The same procedure can be used to make a variety of glass tools, including injection needles.

Tornando-Patch pipetas e Eletrodos Sharp com um extrator programável

Glass microelectrodes (also called pipettes) have been a workhorse of electrophysiology for decades.  Today, such pipettes are made from glass capillaries ...

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may also be used to study the structure-function relationship for other ion channels and neurotransmitter receptors1. BK channels are widely expressed in different tissues and have been implicated in many physiological functions, including regulation of smooth muscle contraction, frequency tuning of inner hair cells and regulation of neurotransmitter release2-6. BK channels are activated by membrane depolarization and by intracellular Ca2+ and Mg2+ 6-9. Therefore, the protocol is designed to control both the membrane voltage and the intracellular solution. In this protocol, messenger RNA of BK channels is injected into Xenopus laevis oocytes (stage V-VI) followed by 2-5 days of incubation at 18&deg;C10-13. Membrane patches that contain single or multiple BK channels are excised with the inside-out configuration using patch clamp techniques10-13. The intracellular side of the patch is perfused with desired solutions during recording so that the channel activation under different conditions can be examined. To summarize, the mRNA of BK channels is injected into Xenopus laevis oocytes to express channel proteins on the oocyte membrane; patch clamp techniques are used to record currents flowing through the channels under controlled voltage and intracellular solutions.

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Ionic current of BK channels is recorded using patch clamp techniques. BK channels are expressed in Xenopus oocytes by injecting messenger RNA. The intracellular solution during patch clamp recordings is controlled by a perfusion system.

Grampo patch e Técnicas de Perfusão para estudar canais iônicos Expresso em Xenopus Oócitos

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may ...

Aseptic Laboratory Techniques: Volume Transfers with Serological Pipettes and Micropipettors

Microorganisms are everywhere - in the air, soil, and human body as well as on inanimate surfaces like laboratory benches and computer keyboards. The ubiquity of microbes creates a copious supply of potential contaminants in a laboratory. To ensure experimental success, the number of contaminants on equipment and work surfaces must be minimized. Common among many experiments in microbiology are techniques involving the measurement and transfer of cultures containing bacterial cells or viral particles. To do so without contacting non-sterile surfaces or contaminating sterile media requires (1) preparing a sterile workspace, (2) precisely setting and accurately reading instruments for aseptic transfer of liquids, and (3) properly manipulating instruments, cultures flasks, bottles and tubes within a sterile field. Learning these procedures calls for training and practice. At first, actions should be slow, deliberate, and controlled with the goal being for aseptic technique to become second nature when working at the bench. Here we present the steps for measuring volumes using serological pipettes and micropipettors within a sterile field created by a Bunsen burner. Volumes range from microliters (&mu;l) to milliliters (ml) depending on the instrument used. Liquids commonly transferred include sterile broth or chemical solutions as well as bacterial cultures and phage stocks. By following these procedures, students should be able to: &#8226;Work within the sterile field created by the Bunsen burner flame. &#8226;Use serological pipettes without compromising instrument sterility.&#8226; Aspirate liquids with serological pipettes, precisely reading calibrated volumes by aligning the meniscus formed by the liquid to the graduation marks on the pipette. &#8226;Keep culture bottles, flasks, tubes and their respective caps sterile during liquid transfers. &#8226;Identify different applications for plastic versus glass serological pipettes. &#8226;State accuracy limitations for micropipettors. &#8226;Precisely and accurately set volumes on micropipettors. &#8226;Know how to properly use the first and second stop on a micropipettor to aspirate and transfer correct volumes.

When working in a laboratory, it is imperative to minimize sources of contamination. Aseptic technique refers to procedures that permit transfer of cultures and reagents while avoiding contact with non-sterile surfaces. Serological pipettes and micropipettors are used to measure precise volumes without compromising sterility of solutions used in experiments.

Assépticas Técnicas de Laboratório: transferências de volume com pipetas sorológicas e micropipetas

Microorganisms are everywhere - in the air, soil, and human body as well as on inanimate surfaces like laboratory benches and computer keyboards. The ...

Exploring Arterial Smooth Muscle Kv7 Potassium Channel Function using Patch Clamp Electrophysiology and Pressure Myography

Contraction or relaxation of smooth muscle cells within the walls of resistance arteries determines the artery diameter and thereby controls flow of blood through the vessel and contributes to systemic blood pressure. The contraction process is regulated primarily by cytosolic calcium concentration ([Ca2+]cyt), which is in turn controlled by a variety of ion transporters and channels. Ion channels are common intermediates in signal transduction pathways activated by vasoactive hormones to effect vasoconstriction or vasodilation. And ion channels are often targeted by therapeutic agents either intentionally (e.g. calcium channel blockers used to induce vasodilation and lower blood pressure) or unintentionally (e.g. to induce unwanted cardiovascular side effects).
Kv7 (KCNQ) voltage-activated potassium channels have recently been implicated as important physiological and therapeutic targets for regulation of smooth muscle contraction. To elucidate the specific roles of Kv7 channels in both physiological signal transduction and in the actions of therapeutic agents, we need to study how their activity is modulated at the cellular level as well as evaluate their contribution in the context of the intact artery.
The rat mesenteric arteries provide a useful model system. The arteries can be easily dissected, cleaned of connective tissue, and used to prepare isolated arterial myocytes for patch clamp electrophysiology, or cannulated and pressurized for measurements of vasoconstrictor/vasodilator responses under relatively physiological conditions. Here we describe the methods used for both types of measurements and provide some examples of how the experimental design can be integrated to provide a clearer understanding of the roles of these ion channels in the regulation of vascular tone.

Measurements of Kv7 (KCNQ) potassium channel activity in isolated arterial myocytes (using patch clamp electrophysiological techniques) in parallel with measurements of constrictor/dilator responses (using pressure myography) can reveal important information about the roles of Kv7 channels in vascular smooth muscle physiology and pharmacology.

Explorando Arterial Músculo Liso KV7 função dos canais de potássio utilizando electrofisiologia patch clamp e Miografia Pressão

Contraction  or relaxation of smooth muscle cells within the walls of resistance arteries  determines the artery diameter and thereby controls flow of ...

Giant Liposome Preparation for Imaging and Patch-Clamp Electrophysiology

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify and explore the function of these important proteins. However, classical preparations, such as planar bilayers, limit the manipulations and experiments that can be performed on the reconstituted channel and its membrane environment. The more cell-like structure of giant liposomes permits traditional patch-clamp experiments without sacrificing control of the lipid environment.
Electroformation is an efficient mean to produce giant liposomes &gt;10 &mu;m in diameter which relies on the application of alternating voltage to a thin, ordered lipid film deposited on an electrode surface. However, since the classical protocol calls for the lipids to be deposited from organic solvents, it is not compatible with less robust membrane proteins like ion channels and must be modified. Recently, protocols have been developed to electroform giant liposomes from partially dehydrated small liposomes, which we have adapted to protein-containing liposomes in our laboratory.
We present here the background, equipment, techniques, and pitfalls of electroformation of giant liposomes from small liposome dispersions. We begin with the classic protocol, which should be mastered first before attempting the more challenging protocols that follow. We demonstrate the process of controlled partial dehydration of small liposomes using vapor equilibrium with saturated salt solutions. Finally, we demonstrate the process of electroformation itself. We will describe simple, inexpensive equipment that can be made in-house to produce high-quality liposomes, and describe visual inspection of the preparation at each stage to ensure the best results.

Reconstituting functional membrane proteins into giant liposomes of defined composition is a powerful approach when combined with patch-clamp electrophysiology. However, conventional giant liposome production may be incompatible with protein stability. We describe protocols for producing giant liposomes from pure lipids or small liposomes containing ion channels.

Preparação de lipossomas gigantes por Imagem e patch-clamp Eletrofisiologia

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify ...

One-channel Cell-attached Patch-clamp Recording

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate depends on properties intrinsic to each channel protein as well as the mechanism by which it is generated and controlled and represents an important area of current research. Information about the operational dynamics of ion channel proteins can be obtained by observing long stretches of current produced by a single molecule. Described here is a protocol for obtaining one-channel cell-attached patch-clamp current recordings for a ligand gated ion channel, the NMDA receptor, expressed heterologously in HEK293 cells or natively in cortical neurons. Also provided are instructions on how to adapt the method to other ion channels of interest by presenting the example of the mechano-sensitive channel PIEZO1. This method can provide data regarding the channel&#8217;s conductance properties and the temporal sequence of open-closed conformations that make up the channel&#8217;s activation mechanism, thus helping to understand their functions in health and disease.

Described here is a procedure for obtaining long stretches of current recording from one ion channel with the cell-attached patch-clamp technique. This method allows for observing, in real time, the pattern of open-close channel conformations that underlie the biological signal. These data inform about channel properties in undisturbed biological membranes.

Um canal de gravação de patch-clamp anexado-Cell

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate ...

Reconstitution of a Transmembrane Protein, the Voltage-gated Ion Channel, KvAP, into Giant Unilamellar Vesicles for Microscopy and Patch Clamp Studies

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow GUVs must be modified in order to form GUVs containing functional transmembrane proteins. This article describes two dehydration-rehydration methods &#8212; electroformation and gel-assisted swelling &#8212; to form GUVs containing the voltage-gated potassium channel, KvAP. In both methods, a solution of protein-containing small unilamellar vesicles is partially dehydrated to form a stack of membranes, which is then allowed to swell in a rehydration buffer. For the electroformation method, the film is deposited on platinum electrodes so that an AC field can be applied during film rehydration. In contrast, the gel-assisted swelling method uses an agarose gel substrate to enhance film rehydration. Both methods can produce GUVs in low (e.g., 5 mM) and physiological (e.g., 100 mM) salt concentrations. The resulting GUVs are characterized via fluorescence microscopy, and the function of reconstituted channels measured using the inside-out patch-clamp configuration. While swelling in the presence of an alternating electric field (electroformation) gives a high yield of defect-free GUVs, the gel-assisted swelling method produces a more homogeneous protein distribution and requires no special equipment.

The reconstitution of the transmembrane protein, KvAP, into giant unilamellar vesicles (GUVs) is demonstrated for two dehydration-rehydration methods &#8212; electroformation, and gel-assisted swelling. In both methods, small unilamellar vesicles containing the protein are fused together to form GUVs that can then be studied by fluorescence microscopy and patch-clamp electrophysiology.

Reconstituição de uma proteína transmembrana, a voltagem-Ion Channel, KvAP, em Gigante Unilamelares Vesicles para microscopia e de Patch Estudos Grampo

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow ...

Implementing Patch Clamp and Live Fluorescence Microscopy to Monitor Functional Properties of Freshly Isolated PKD Epithelium

Cyst initiation and expansion during polycystic kidney disease is a complex process characterized by abnormalities in tubular cell proliferation, luminal fluid accumulation and extracellular matrix formation. Activity of ion channels and intracellular calcium signaling are key physiologic parameters which determine functions of tubular epithelium. We developed a method suitable for real-time observation of ion channels activity with patch-clamp technique and registration of intracellular Ca2+ level in epithelial monolayers freshly isolated from renal cysts. PCK rats, a genetic model of autosomal recessive polycystic kidney disease (ARPKD), were used here for ex vivo analysis of ion channels and calcium flux. Described here is a detailed step-by-step procedure designed to isolate cystic monolayers and non-dilated tubules from PCK or normal Sprague Dawley (SD) rats, and monitor single channel activity and intracellular Ca2+ dynamics. This method does not require enzymatic processing and allows analysis in a native setting of freshly isolated epithelial monolayer. Moreover, this technique is very sensitive to intracellular calcium changes and generates high resolution images for precise measurements. Finally, isolated cystic epithelium can be further used for staining with antibodies or dyes, preparation of primary cultures and purification for various biochemical assays.

Ion channels expressed in renal tubular epithelium play a significant role in the pathology of polycystic kidney disease. Here we describe experimental protocols used to perform patch-clamp analysis and intracellular calcium level measurements in cystic epithelium freshly isolated from rodent kidneys.

Implementando Grampo patch e ao vivo microscopia de fluorescência para monitorar propriedades funcionais de recentemente isolados PKD Epithelium

Cyst initiation and expansion during polycystic kidney disease is a complex process characterized by abnormalities in tubular cell proliferation, luminal ...