SR Lockery ile işbirliği içinde basınç parlatma tekniği geliştirildi.

Çekme pipetler Çektirmesi gibi filament kullanarak bir Sutter P-97 / Kahverengi Mikroelektrod Çektirme Flaming, yaklaşık 10-20 pipetler bir set çekin. <ol><li> Cam seçin. Biz borosilikat (BF150-86-10, OD = 1.5 mm, ID = 0.86 mm) kullanın. Temiz ve tozsuz kalır cam dikkatlice saklayın. </li><li> Çekme programı tasarlayın. Birincil amacı, uygulamaya bağlı olacaktır yaklaşık istenen boyut, açılan bir ucu. Sutter P-97-Pipet Yemek Tarifleri 2 mükemmel bir referans. </li><li> Açılış çap ve pürüzsüzlük belirlemek için mikroskop altında pipetler uyun. Kaba, düzensiz ya da düzensiz ipuçları atın. Karşısında 2-4 mikron olan bir ucu açılış standart yama kelepçe kayıt için en iyisidir. Künt ucu tercih edilir aynı açılış çapı, direnci düşük açar. Şekli ve boyutu aşağıda, parlatma sırasında değiştirilebilir. </li></ol> Basınç parlatma pipetler <ol><li> Temiz, sıkıştırılmış hava hattı için bir pipet tutucu takın. Bir regülatör kullanarak, sıkıştırılmış hava hattı basıncı ~ 40 PSI ayarlayın. Pipet tutucu basıncı ve devre dışı bırakılmasına izin verecek bir 4-yönlü kontrol valfi basınçlı hava hattı bağlayın. Tygon ⅛, uzunluğu ® boru ile kontrol vanası bir pipet tutucu bağlayın. </li><li> Yüksek basınçlı bir pipet tutucu, bir ayak pedalı, düşük ve yüksek büyütme, uzun çalışma mesafesi (ideal, 10x ve 100x) hava hedefleri ile donatılmış bir mikroskop tarafından kontrol edilen bir parlatma bobini ile parlatma teçhizat (microforge) kullanın. Pipet açılışı protokol sırasında gözlemlemek edebilmek için kritik öneme sahiptir. </li><li> İsteğe Bağlı: Kat kapasitans azaltmak ve gürültü özelliklerinin iyileştirilmesi (&quot;bölümüne bakın&quot; Çekme pipetler, bu tekniğin) hidrofobik bir yalıtkan pipet . </li><li> Basınç valfi kapalı konumda olduğundan emin olun. Pipet pipet tutucu içine yerleştirin ve parmak sıkı uydurma sıkın. Güvenlik notu: pipet pipet tutucu içine sıkıca tutulur, hava basıncı, pipet pipet tutucu uzaklaştırılırlar neden olacaktır . </li><li> Microforge pipet ve tutucu yerleştirin. Mikroskop sahneye pozisyon pipet tutucu ucu ve parlatma bobin hem microforge düşük güçte (10x) görülebilir. ~ 75 mikron filament ucu getir. Isıtıldığında filament genişletmek olacağını aklınızda bulundurun. </li><li> Yüksek güç (100x) amacı geçin. Pipet ve parlatma bobin Her iki odak ve görüş alanı içinde olmalıdır. Değilse, parlatma bobin yükseklik ayarı. (Pipet konumu ayarlanabilir olamaz). Pipet ve parlatma bobini zıt görüş alanında yakın olmalıdır. Onu ısıtır olarak genişletmek ve pipet içine darbelerim çünkü çok pipet yakın bobin koymaktan kaçının. </li><li> Pipet içine basınçlı hava doğrudan vana açın ve pipet ucu arkasındaki konik dışa balon başlayana kadar ısıtmak. </li><li> Isıtma ucu çok yoğun balonlar önce durdurun. Deney için uygun mesafe, ısı ve zaman istenilen şekil belirlemek için gereklidir. </li><li> İsteğe Bağlı: basınç yokluğunda ucu parlatma ucu açılış çapı azaltın. 7. ve 8. adımları pipet şekli ve boyutları hem de ince ayar yapmak için tekrar tekrar. </li><li> Basınç kapatın ve pipet güvenli bir yöne işaret ederken, pipet kaldırmak ve tozdan korunacak temiz bir saklama kutusu yerleştirin. Güvenlik notu: hava basıncı kapalı değilse, kaldırma sırasında pipet pipet tutucu çıkartıldığı olabilir. </li></ol> Microforge ilgili notlar Off-the-raf piyasada bulunan parçaları monte microforge kullanın. (Ayrıca birkaç şirket, örneğin, ALA Bilim, GlassWorx bir basınç parlatma kiti satın alabilirsiniz). Microforge ne olursa olsun, genellikle sadece birkaç mikron çapında ucu açılması, görmek için yeterli olan optik olması esastır. Bunun için uzun bir çalışma mesafesi 100x objektif kullanın. Ayrıca, mont için yüksek ergime sıcaklığına sahip cam parlatma bobin pipetler buharlaşmış dolgu en aza indirmek için. Bölüm 3: Beklenen Sonuçlar Orta basınç parlatma çapı açılması kayda değer bir değişiklik olmadan bir pipetle direnci azaltabilir. İsterseniz, bu protokolü 5-10M arasında mikron alt açıklıkların ve dirençleri pipetler yapmak için kullanılabilir.

<ol>
	<li>Goodman, M. B., Lockery, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Pressure+polishing:+a+method+for+re-shaping+patch+pipettes+during+fire+polishing. .">Pressure polishing: a method for re-shaping patch pipettes during fire polishing. .</a> J Neurosci Methods. 100, 13-15 (2000).</li></ol>

Biz aslında C. 2-3 mikron nöronlardan gelen patch-klemp kayıt için pipetler yararlı hale getirmek için bu yöntem geliştirdi elegans 1. Goodman laboratuvarda rutin olarak kullanılması. Biz sadece kayıt için küçük C. basınç lehçe pipetler elegans nöronlar, aynı zamanda iyon kanalları Xenopus oositleri ifade macropatch ve tek kanallı kayıtları elde etmek için. Belirli bir ucu açılması çapı için, künt şekli, düşük bir direnç pipet oluşturur. Alt pipet direnci d...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Glass Capillaries</td>
<td>Consumable</td>
<td>Sutter Instruments</td>
<td>BF150-85-10 (or similar)</td>
<td>The method works with any type of capillary except those made from quartz. However, we recommend using capillaries with a filament.</td>
</tr>
<tr>
<td>Inverted Microscope</td>
<td>Microscope</td>
<td>Leica</td>
<td>DM IL (or similar)</td>
<td>Any simple inverted microscope will do. However, it is essential to have sufficient magnification to see pipettes during polishing. We use a 100x metallurgical lens with a long working distance for this purpose.</td>
</tr>
<tr>
<td>Microforge Kit</td>
<td>Tool</td>
<td>ALA Science</td>
<td>CPM-2</td>
<td>Supplies polishing coil, controller and foot pedal.</td>
</tr>
<tr>
<td>Air pressure source</td>
<td>Tool</td>
<td>ALA Science</td>
<td>PR-60</td>
<td>Accessory for providing high pressure, includes a suitable valve. Alternatively, compressed air from the building can be used together with a filter/regulator (set to 40 PSI) and a 4-way valve (see below)</td>
</tr>
<tr>
<td>4-way valve</td>
<td>Tool</td>
<td>Cole-Parmer</td>
<td>A-98150-01</td>
<td>Fittings will be needed to couple valve to tubing</td>
</tr>
<tr>
<td>Pipette Holder with Luer Connector</td>
<td>Tool</td>
<td>World Precision Instruments</td>
<td>MPH-6S20</td>
<td>Use a male luer-to-barb fitting to connect pipette holder to high-pressure tubing</td>
</tr>
<tr>
<td>Tygon&#174; tubing</td>
<td>Tool</td>
<td>Cole-Parmer</td>
<td>06408-62</td>
<td>Use this tubing to connect pipette holder to 4-way valve
</td>
</tr>		</tbody>
		</table>
		</div>

pressure-polishing pipettes for improved patch-clamp recording

Basınç-parlatma yama klemp kayıt için cam pipetler şekillendirmek için kullanılan bir yöntemdir. Biz ilk olarak küçük (&lt;3 m) nöronal hücre gövdeleri kayıt için uygun pipetler imalatı için bu yöntemi geliştirdi. Temel prensip, cam üfleme benzer ve geleneksel bir mikropipet çektirmenin tarafından hazırlanan yama pipetler şeklini değiştirmek için, hava basıncı ve ısı birleştirir. Bu sözde yumuşak (kostik soda) ve sert (borosilikat) gözlük uygulanabilir. Genel olarak konuşmak gerekirse, basınç parlatma ucu açıklığı (Goodman ve Lockery, 2000) çapı düşürmeden, pipetle direnci% 25 oranında azaltabilir. Hemen her tür cam uygulanan ve bir yüksek basınç valfi ve bir microforge monte sadece ek gerektirir. Bu teknik ultrasmall hücreleri (&lt;5 m) kayıt için gerekli ve ayrıca pipet direnci en aza indirerek, tek kanallı kayıt artırabilirsiniz. Künt şekli delikli yama kelepçe kayıt için de yararlıdır perforasyonu için daha büyük bir membran bleb bu ucu şeklini sonuçları.

Watch this Scientific Journal Video about Pressure-polishing Pipettes for Improved Patch-clamp Recording at JoVE.com

Pressure-polishing Pipettes for Improved Patch-clamp Recording

Bu cam mikropipetler şeklini değiştirerek bir kılavuzdur. Özellikle, ısı ve hava basıncı ile konik pipet direnci azaltmak için, ucu açıklığı artırmadan genişletilinceye. Bu küçük hücrelerin düşük gürültü kayıtları elde etmek için kritik öneme sahiptir, ancak birçok uygulamada yararlıdır.

Geliştirilmiş Patch-kelepçe kayıt için Basınç-parlatma Pipetler

Pressure-polishing is a method for shaping glass pipettes for patch-clamp recording.  We first developed this method for fabricating pipettes suitable for ...

pressure-polishing-pipettes-for-improved-patch-clamp-recording

Research

JoVE Journal

Biology

12.9K Görüntüleme.  Stanford University School of Medicine. Bu cam mikropipetler şeklini değiştirerek bir kılavuzdur. Özellikle, ısı ve hava basıncı ile konik pipet direnci azaltmak için, ucu açıklığı artırmadan genişletilinceye. Bu küçük hücrelerin düşük gürültü kayıtları elde etmek için kritik öneme sahiptir, ancak birçok uygulamada yararlıdır.

Video: Pressure-polishing Pipettes for Improved Patch-clamp Recording

Methods for Patch Clamp Capacitance Recordings from the Calyx

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. Electrical recordings from the presynaptic terminal allow the measurement of action potentials, calcium channel currents, vesicle fusion (exocytosis) and subsequent membrane uptake (endocytosis). The fusion of vesicles containing neurotransmitter causes the vesicle membrane to be added to the cell membrane of the calyx. This increase in the amount of cell membrane is measured as an increase in capacitance. The subsequent reduction in capacitance indicates endocytosis, the process of membrane uptake or removal from the calyx membrane. Endocytosis, is necessary to maintain the structure of the calyx and it is also necessary to form vesicles that will be filled with neurotransmitter for future exocytosis events. Capacitance recordings at the calyx of Held have made it possible to directly and rapidly measure vesicular release and subsequent endocytosis in a mammalian CNS nerve terminal. In addition, the corresponding postsynaptic activity can be simultaneously measured by using paired recordings. Thus a complete picture of the presynaptic and postsynaptic electrical activity at a central nervous system synapse is achievable using this preparation. Here, the methods for slice preparation, morphological features for identification of calyces of Held, basic patch clamping techniques, and examples of capacitance recordings to measure exocytosis and endocytosis are presented.

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal.

Kaliks Patch Kelepçe Kapasitans Kayıtlar Yöntemleri

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. ...

Biyoloji

Patch Clamp Recording of Ion Channels Expressed in  Xenopus Oocytes

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological measurement of single or multiple ion channels in cells. This technique can be applied to ion channels in both their native environment and expressed in heterologous cells, such as oocytes harvested from the African clawed frog, Xenopus laevis. Here, we describe the well-established technique of patch clamp recording from Xenopus oocytes. This technique is used to measure the properties of expressed ion channels either in populations (macropatch) or individually (single-channel recording). We focus on techniques to maximize the quality of oocyte preparation and seal generation. With all factors optimized, this technique gives a probability of successful seal generation over 90 percent. The process may be optimized differently by every researcher based on the factors he or she finds most important, and we present the approach that have lead to the greatest success in our hands.

This is intended as an introduction to patch clamp recording from Xenopus laevis oocytes. It covers vitelline membrane removal, formation of a gigaohm seal (gigaseal), and the optional conversion of the patch to the outside-out topology.

Xenopus Oosit ifade İyon Kanalları Patch Kelepçe Kaydı

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological ...

Making Patch-pipettes and Sharp Electrodes with a Programmable Puller

Glass microelectrodes (also called pipettes) have been a workhorse of electrophysiology for decades. Today, such pipettes are made from glass capillaries using a programmable puller. Such instruments heat the capillary using either a metal filament or a laser and draw out the glass using gravity, a motor or both. Pipettes for patch-clamp recording are formed using only heat and gravity, while sharp electrodes for intracellular recording use a combination of heat, gravity, and a motor. The procedure used to make intracellular recording pipettes is similar to that used to make injection needles for a variety of applications, including cRNA injection into Xenopus oocytes. In general, capillary glass &lt;1.2 mm in diameter is used to make pipettes for patch clamp recording, while narrower glass is used for intracellular recording (outer diameter = 1.0 mm). For each tool, the puller is programmed slightly differently. This video shows how to make both kinds of recording pipettes using pre-established puller programs.

This video shows how to use a programmable puller to make patch pipettes and sharp electrodes for electrophysiology. The same procedure can be used to make a variety of glass tools, including injection needles.

Programlanabilir Çektirme Patch-pipetler ve Sharp Elektrotlar

Glass microelectrodes (also called pipettes) have been a workhorse of electrophysiology for decades.  Today, such pipettes are made from glass capillaries ...

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may also be used to study the structure-function relationship for other ion channels and neurotransmitter receptors1. BK channels are widely expressed in different tissues and have been implicated in many physiological functions, including regulation of smooth muscle contraction, frequency tuning of inner hair cells and regulation of neurotransmitter release2-6. BK channels are activated by membrane depolarization and by intracellular Ca2+ and Mg2+ 6-9. Therefore, the protocol is designed to control both the membrane voltage and the intracellular solution. In this protocol, messenger RNA of BK channels is injected into Xenopus laevis oocytes (stage V-VI) followed by 2-5 days of incubation at 18&deg;C10-13. Membrane patches that contain single or multiple BK channels are excised with the inside-out configuration using patch clamp techniques10-13. The intracellular side of the patch is perfused with desired solutions during recording so that the channel activation under different conditions can be examined. To summarize, the mRNA of BK channels is injected into Xenopus laevis oocytes to express channel proteins on the oocyte membrane; patch clamp techniques are used to record currents flowing through the channels under controlled voltage and intracellular solutions.

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Ionic current of BK channels is recorded using patch clamp techniques. BK channels are expressed in Xenopus oocytes by injecting messenger RNA. The intracellular solution during patch clamp recordings is controlled by a perfusion system.

İyon Kanalları incelenmesi için yama Kelepçe ve Perfüzyon Teknikleri cinsinden ifade edilir Xenopus Oosit

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may ...

Aseptic Laboratory Techniques: Volume Transfers with Serological Pipettes and Micropipettors

Microorganisms are everywhere - in the air, soil, and human body as well as on inanimate surfaces like laboratory benches and computer keyboards. The ubiquity of microbes creates a copious supply of potential contaminants in a laboratory. To ensure experimental success, the number of contaminants on equipment and work surfaces must be minimized. Common among many experiments in microbiology are techniques involving the measurement and transfer of cultures containing bacterial cells or viral particles. To do so without contacting non-sterile surfaces or contaminating sterile media requires (1) preparing a sterile workspace, (2) precisely setting and accurately reading instruments for aseptic transfer of liquids, and (3) properly manipulating instruments, cultures flasks, bottles and tubes within a sterile field. Learning these procedures calls for training and practice. At first, actions should be slow, deliberate, and controlled with the goal being for aseptic technique to become second nature when working at the bench. Here we present the steps for measuring volumes using serological pipettes and micropipettors within a sterile field created by a Bunsen burner. Volumes range from microliters (&mu;l) to milliliters (ml) depending on the instrument used. Liquids commonly transferred include sterile broth or chemical solutions as well as bacterial cultures and phage stocks. By following these procedures, students should be able to: &#8226;Work within the sterile field created by the Bunsen burner flame. &#8226;Use serological pipettes without compromising instrument sterility.&#8226; Aspirate liquids with serological pipettes, precisely reading calibrated volumes by aligning the meniscus formed by the liquid to the graduation marks on the pipette. &#8226;Keep culture bottles, flasks, tubes and their respective caps sterile during liquid transfers. &#8226;Identify different applications for plastic versus glass serological pipettes. &#8226;State accuracy limitations for micropipettors. &#8226;Precisely and accurately set volumes on micropipettors. &#8226;Know how to properly use the first and second stop on a micropipettor to aspirate and transfer correct volumes.

When working in a laboratory, it is imperative to minimize sources of contamination. Aseptic technique refers to procedures that permit transfer of cultures and reagents while avoiding contact with non-sterile surfaces. Serological pipettes and micropipettors are used to measure precise volumes without compromising sterility of solutions used in experiments.

Aseptik Laboratuvar Teknikleri: Serolojik Pipetler ve Micropipettors ile Cilt Transferler

Microorganisms are everywhere - in the air, soil, and human body as well as on inanimate surfaces like laboratory benches and computer keyboards. The ...

Exploring Arterial Smooth Muscle Kv7 Potassium Channel Function using Patch Clamp Electrophysiology and Pressure Myography

Contraction or relaxation of smooth muscle cells within the walls of resistance arteries determines the artery diameter and thereby controls flow of blood through the vessel and contributes to systemic blood pressure. The contraction process is regulated primarily by cytosolic calcium concentration ([Ca2+]cyt), which is in turn controlled by a variety of ion transporters and channels. Ion channels are common intermediates in signal transduction pathways activated by vasoactive hormones to effect vasoconstriction or vasodilation. And ion channels are often targeted by therapeutic agents either intentionally (e.g. calcium channel blockers used to induce vasodilation and lower blood pressure) or unintentionally (e.g. to induce unwanted cardiovascular side effects).
Kv7 (KCNQ) voltage-activated potassium channels have recently been implicated as important physiological and therapeutic targets for regulation of smooth muscle contraction. To elucidate the specific roles of Kv7 channels in both physiological signal transduction and in the actions of therapeutic agents, we need to study how their activity is modulated at the cellular level as well as evaluate their contribution in the context of the intact artery.
The rat mesenteric arteries provide a useful model system. The arteries can be easily dissected, cleaned of connective tissue, and used to prepare isolated arterial myocytes for patch clamp electrophysiology, or cannulated and pressurized for measurements of vasoconstrictor/vasodilator responses under relatively physiological conditions. Here we describe the methods used for both types of measurements and provide some examples of how the experimental design can be integrated to provide a clearer understanding of the roles of these ion channels in the regulation of vascular tone.

Measurements of Kv7 (KCNQ) potassium channel activity in isolated arterial myocytes (using patch clamp electrophysiological techniques) in parallel with measurements of constrictor/dilator responses (using pressure myography) can reveal important information about the roles of Kv7 channels in vascular smooth muscle physiology and pharmacology.

Patch Clamp Elektrofizyoloji ve Basınç kasılmaların kâğıda çizilmesi kullanarak arteriyel düz kas KV7 Potasyum Kanal Fonksiyon Exploring

Contraction  or relaxation of smooth muscle cells within the walls of resistance arteries  determines the artery diameter and thereby controls flow of ...

Giant Liposome Preparation for Imaging and Patch-Clamp Electrophysiology

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify and explore the function of these important proteins. However, classical preparations, such as planar bilayers, limit the manipulations and experiments that can be performed on the reconstituted channel and its membrane environment. The more cell-like structure of giant liposomes permits traditional patch-clamp experiments without sacrificing control of the lipid environment.
Electroformation is an efficient mean to produce giant liposomes &gt;10 &mu;m in diameter which relies on the application of alternating voltage to a thin, ordered lipid film deposited on an electrode surface. However, since the classical protocol calls for the lipids to be deposited from organic solvents, it is not compatible with less robust membrane proteins like ion channels and must be modified. Recently, protocols have been developed to electroform giant liposomes from partially dehydrated small liposomes, which we have adapted to protein-containing liposomes in our laboratory.
We present here the background, equipment, techniques, and pitfalls of electroformation of giant liposomes from small liposome dispersions. We begin with the classic protocol, which should be mastered first before attempting the more challenging protocols that follow. We demonstrate the process of controlled partial dehydration of small liposomes using vapor equilibrium with saturated salt solutions. Finally, we demonstrate the process of electroformation itself. We will describe simple, inexpensive equipment that can be made in-house to produce high-quality liposomes, and describe visual inspection of the preparation at each stage to ensure the best results.

Reconstituting functional membrane proteins into giant liposomes of defined composition is a powerful approach when combined with patch-clamp electrophysiology. However, conventional giant liposome production may be incompatible with protein stability. We describe protocols for producing giant liposomes from pure lipids or small liposomes containing ion channels.

Görüntüleme ve Patch-Kelepçe Elektrofizyoloji için dev Liposome Hazırlık

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify ...

One-channel Cell-attached Patch-clamp Recording

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate depends on properties intrinsic to each channel protein as well as the mechanism by which it is generated and controlled and represents an important area of current research. Information about the operational dynamics of ion channel proteins can be obtained by observing long stretches of current produced by a single molecule. Described here is a protocol for obtaining one-channel cell-attached patch-clamp current recordings for a ligand gated ion channel, the NMDA receptor, expressed heterologously in HEK293 cells or natively in cortical neurons. Also provided are instructions on how to adapt the method to other ion channels of interest by presenting the example of the mechano-sensitive channel PIEZO1. This method can provide data regarding the channel&#8217;s conductance properties and the temporal sequence of open-closed conformations that make up the channel&#8217;s activation mechanism, thus helping to understand their functions in health and disease.

Described here is a procedure for obtaining long stretches of current recording from one ion channel with the cell-attached patch-clamp technique. This method allows for observing, in real time, the pattern of open-close channel conformations that underlie the biological signal. These data inform about channel properties in undisturbed biological membranes.

Tek kanallı bir hücre-bağlı Patch-clamp kayıt

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate ...

Reconstitution of a Transmembrane Protein, the Voltage-gated Ion Channel, KvAP, into Giant Unilamellar Vesicles for Microscopy and Patch Clamp Studies

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow GUVs must be modified in order to form GUVs containing functional transmembrane proteins. This article describes two dehydration-rehydration methods &#8212; electroformation and gel-assisted swelling &#8212; to form GUVs containing the voltage-gated potassium channel, KvAP. In both methods, a solution of protein-containing small unilamellar vesicles is partially dehydrated to form a stack of membranes, which is then allowed to swell in a rehydration buffer. For the electroformation method, the film is deposited on platinum electrodes so that an AC field can be applied during film rehydration. In contrast, the gel-assisted swelling method uses an agarose gel substrate to enhance film rehydration. Both methods can produce GUVs in low (e.g., 5 mM) and physiological (e.g., 100 mM) salt concentrations. The resulting GUVs are characterized via fluorescence microscopy, and the function of reconstituted channels measured using the inside-out patch-clamp configuration. While swelling in the presence of an alternating electric field (electroformation) gives a high yield of defect-free GUVs, the gel-assisted swelling method produces a more homogeneous protein distribution and requires no special equipment.

The reconstitution of the transmembrane protein, KvAP, into giant unilamellar vesicles (GUVs) is demonstrated for two dehydration-rehydration methods &#8212; electroformation, and gel-assisted swelling. In both methods, small unilamellar vesicles containing the protein are fused together to form GUVs that can then be studied by fluorescence microscopy and patch-clamp electrophysiology.

Bir transmembran proteinin yeniden oluşturulması, Mikroskop ve yama kelepçe Çalışmaları Dev tek-katmanlı keseler içine Voltaj kapılı iyon kanalı, KvAP,

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow ...

Implementing Patch Clamp and Live Fluorescence Microscopy to Monitor Functional Properties of Freshly Isolated PKD Epithelium

Cyst initiation and expansion during polycystic kidney disease is a complex process characterized by abnormalities in tubular cell proliferation, luminal fluid accumulation and extracellular matrix formation. Activity of ion channels and intracellular calcium signaling are key physiologic parameters which determine functions of tubular epithelium. We developed a method suitable for real-time observation of ion channels activity with patch-clamp technique and registration of intracellular Ca2+ level in epithelial monolayers freshly isolated from renal cysts. PCK rats, a genetic model of autosomal recessive polycystic kidney disease (ARPKD), were used here for ex vivo analysis of ion channels and calcium flux. Described here is a detailed step-by-step procedure designed to isolate cystic monolayers and non-dilated tubules from PCK or normal Sprague Dawley (SD) rats, and monitor single channel activity and intracellular Ca2+ dynamics. This method does not require enzymatic processing and allows analysis in a native setting of freshly isolated epithelial monolayer. Moreover, this technique is very sensitive to intracellular calcium changes and generates high resolution images for precise measurements. Finally, isolated cystic epithelium can be further used for staining with antibodies or dyes, preparation of primary cultures and purification for various biochemical assays.

Ion channels expressed in renal tubular epithelium play a significant role in the pathology of polycystic kidney disease. Here we describe experimental protocols used to perform patch-clamp analysis and intracellular calcium level measurements in cystic epithelium freshly isolated from rodent kidneys.

Patch Kelepçe ve Canlı Floresan Mikroskobu uygulanması Taze İzole PKD Epitelinin Fonksiyonel Properties Monitör

Cyst initiation and expansion during polycystic kidney disease is a complex process characterized by abnormalities in tubular cell proliferation, luminal ...