JoVE Logo
АВТОРЫ
СВЯЖИТЕСЬ С НАМИ

Войдите в систему

Core - Civil Engineering

    Chapter 5

    Aggregates and Water

    5.1 : Unsoundness of Aggregate due to Volume Change01:26

    5.1 : Unsoundness of Aggregate due to Volume Change

    Consider a lightweight aggregate with a porous structure. Water entering these pores expands in volume upon freezing, generating hydraulic pressure within ...

    98 views
    5.2 : Deleterious Substances in Aggregate01:25

    5.2 : Deleterious Substances in Aggregate

    Natural sand may contain organic impurities, such as decayed vegetative matter, which interfere with the hydration of cement. A colorimetric test is ...

    153 views
    5.3 : Sieve Analysis and Grading Curves01:19

    5.3 : Sieve Analysis and Grading Curves

    Sieve analysis of aggregates is carried out using a set of sieves stacked in descending order of their aperture size from top to bottom.  The sizes ...

    308 views
    5.4 : Fineness Modulus01:19

    5.4 : Fineness Modulus

    Consider a sample of fine aggregates being sieved through a standard set of sieves. Note the weight of aggregates retained on each sieve. Calculate the ...

    281 views
    5.5 : Types of Aggregate Grading01:15

    5.5 : Types of Aggregate Grading

    Aggregate grading signifies the particle size distribution within a sample of aggregate. Well-graded aggregates contain all the required aggregate size ...

    417 views
    5.6 : Maximum Size of Aggregate01:12

    5.6 : Maximum Size of Aggregate

    Conventionally, the maximum aggregate size is determined by the sieve size that retains at least 15 percent of the particles in a sample set. As the ...

    79 views
    5.7 : Quality of Water01:19

    5.7 : Quality of Water

    Water added to concrete aids in the hydration of cement, contributing to the strength and durability of concrete. Generally, potable water, if available, ...

    87 views
    5.8 : Testing Water Quality01:14

    5.8 : Testing Water Quality

    If the quality of water available for preparing concrete is uncertain, its suitability is determined by comparing the setting time of cement and the ...

    103 views
    5.9 : Aggregates Classification01:29

    5.9 : Aggregates Classification

    Aggregates constitute nearly three-quarters of the total volume of concrete and are classified based on their size, source, composition, and weight. Based ...

    305 views
    5.10 : Shape and Texture of Coarse Aggregate01:25

    5.10 : Shape and Texture of Coarse Aggregate

    The shape of the coarse aggregate is defined by two characteristics: roundness, which indicates the sharpness or angularity of its edges and corners, and ...

    195 views
    5.11 : Bonding and Strength of Aggregate01:12

    5.11 : Bonding and Strength of Aggregate

    The strength of a concrete mix made of rough and angular aggregates is higher than that of smooth and rounded aggregates. This is because a rough surface ...

    140 views
    5.12 : Toughness and Hardness of Aggregate01:22

    5.12 : Toughness and Hardness of Aggregate

    To ensure the durability of a concrete airport runway, the aggregates within the concrete require sufficient toughness to withstand impact forces and ...

    246 views
    5.13 : Specific Gravity of Aggregate01:19

    5.13 : Specific Gravity of Aggregate

    The specific gravity of aggregate is the ratio of the density of aggregates to the density of distilled water at a given temperature. The density of ...

    223 views
    5.14 : Bulk Density of Aggregate01:22

    5.14 : Bulk Density of Aggregate

    The bulk density of aggregates indicates the mass of aggregates within a unit volume, including the void spaces existing among them. It is generally ...

    415 views
    5.15 : Porosity and Absorption of Aggregate01:20

    5.15 : Porosity and Absorption of Aggregate

    The porosity of aggregate refers to the volume of pores in the aggregate. These pores vary in size and are either enclosed within the aggregate or ...

    264 views
    5.16 : Moisture Content and Bulking of Aggregate01:10

    5.16 : Moisture Content and Bulking of Aggregate

    The moisture content of the aggregate is the excess water present on the surface of the aggregate that exists in a saturated and surface-dry state. It is ...

    132 views
    JoVE Logo

    Конфиденциальность

    Условия эксплуатации

    Политика

    СВЯЖИТЕСЬ С НАМИ

    РЕКОМЕНДОВАТЬ БИБЛИОТЕКЕ

    НОВОСТИ JoVE

    Исследования

    Образование

    АВТОРЫ

    Библиотекарь

    О JoVE

    Авторские права © 2025 MyJoVE Corporation. Все права защищены