JoVE Logo
Authors
Contact Us

Sign In

A subscription to JoVE is required to view this content. Sign in or start your free trial.

In This Article

  • Summary
  • Abstract
  • Introduction
  • Protocol
  • Results
  • Discussion
  • Disclosures
  • Acknowledgements
  • Materials
  • References
  • Reprints and Permissions

Summary

Here, we present a protocol for the in situ synthesis of gold nanoparticles (AuNPs) within the interlayer space of layered titanate films without the aggregation of AuNPs. No spectral change was observed even after 4 months. The synthesized material has expected applications in catalysis, photo-catalysis, and the development of cost-effective plasmonic devices.

Abstract

Combinations of metal oxide semiconductors and gold nanoparticles (AuNPs) have been investigated as new types of materials. The in situ synthesis of AuNPs within the interlayer space of semiconducting layered titania nanosheet (TNS) films was investigated here. Two types of intermediate films (i.e., TNS films containing methyl viologen (TNS/MV2+) and 2-ammoniumethanethiol (TNS/2-AET+)) were prepared. The two intermediate films were soaked in an aqueous tetrachloroauric(III) acid (HAuCl4) solution, whereby considerable amounts of Au(III) species were accommodated within the interlayer spaces of the TNS films. The two types of obtained films were then soaked in an aqueous sodium tetrahydroborate (NaBH4) solution, whereupon the color of the films immediately changed from colorless to purple, suggesting the formation of AuNPs within the TNS interlayer. When only TNS/MV2+ was used as the intermediate film, the color of the film gradually changed from metallic purple to dusty purple within 30 min, suggesting that aggregation of AuNPs had occurred. In contrast, this color change was suppressed by using the TNS/2-AET+ intermediate film, and the AuNPs were stabilized for over 4 months, as evidenced by the characteristic extinction (absorption and scattering) band from the AuNPs.

Introduction

Various noble metal nanoparticles (MNPs) exhibit characteristic colors or tones due to their localized surface plasmon resonance (LSPR) properties; thus, MNPs can be used in various optical and/or photochemical applications1-4. Recently, combinations of metal oxide semiconductor (MOS) photocatalysts, such as titanium oxide (TiO2) and MNPs, have been thoroughly investigated as new types of photocatalysts5-14. However, in many cases, very small amounts of MNPs exist on the MOS surface, because most MOS particles have relatively low surface areas. On the other hand, layered metal oxide semiconductors (LMOSs) exhibit photocatalytic properties and have a large surface area, typically several hundred square meters per unit g of an LMOS15-17. In addition, various LMOSs have intercalation properties (i.e., various chemical species can be accommodated within their expandable and large interlayer spaces)15-20. Thus, with a combination of MNPs and LMOSs, it is expected that relatively large amounts of MNPs are hybridized with the semiconductor photocatalysts.

We have reported the first in situ synthesis of copper nanoparticles (CuNPs)21 within the interlayer space of LMOS (titania nanosheet; TNS16-30) transparent films through very simple steps. However, the details of the synthetic procedures and the characterization of the other noble MNPs and TNS hybrids have not yet been reported. Moreover, the CuNPs within the TNS layers were easily oxidized and decolorized under ambient conditions21. As such, we focused on gold nanoparticles (AuNPs), because AuNPs are widely used for various optical, photochemical, and catalytic applications, and it is expected that they will be relatively stable against oxidation3-5,7,8,10-14,28,31,32. Here, we report the synthesis of AuNPs within the interlayer space of TNS and show that 2-ammoniumethanethiol (2-AET+; Figure 1 inset) works effectively as a protective reagent for AuNPs within the interlayer of TNS.

Access restricted. Please log in or start a trial to view this content.

Protocol

Caution: Always use caution when working with chemicals and solutions. Follow the appropriate safety practices and wear gloves, glasses, and a lab coat at all times. Be aware that nanomaterials may have additional hazards as compared to their bulk counterpart.

1. Preparation of Regents

  1. Prepare the methyl viologen aqueous solution by dissolving 0.0012 g of 1,1'-dimethyl-4,4'-bipyridinium dichloride (methyl viologen; MV2+) in 20 ml of water to give 0.2 mM MV2+.
  2. Prepare the gold(III) chloride aqueous solution by dissolving 0.1050 g of gold(III) tetrachloride trihydrate (HAuCl4• 3H2O) in 10 ml of water to give 25 mM HAuCl4.
  3. Prepare the sodium borohydride aqueous solution by dissolving 0.03844 g of sodium tetrahydroborate (NaBH4) in 10 ml of water to give 100 mM NaBH4.
  4. Prepare the 2-ammoniumethanethiol aqueous solution by dissolving 0.2985 g of 2-ammoniumethanethiol chloride salt (2-AET+) in 25 ml of water to give 100 mM 2-AET+.

2. Synthesis of TNS Colloidal Suspensions

NOTE: Titania nanosheets (TNS; Ti0.91O2) were prepared according to the well-established procedure reported previously22,23,30.

  1. Prepare the starting material of layered cesium titanate Cs0.7Ti1.825O4 by calcining a stoichiometric mixture of Cs2CO3 (0.4040 g) and TiO2 (ST-01; 0.5000 g) at 800 °C for 20 hr22. Repeat this twice.
  2. Prepare the protonated layered titanate (H0.7Ti1.825O4·H2O) by repeatedly treating 0.8142 g of cesium titanate with an HCl (100 mM, 81.42 ml) aqueous solution by using a shaker (300 Hz) for 12 hr.
  3. Prepare the exfoliated layered titanate (TNS) colloidal suspensions by stirring the protonated titanate powder (0.0998 g) vigorously (500 rpm) with 25 ml of a 17 mM tetrabutylammonium hydroxide (TBA+ OH−) aqueous solution for about 2 weeks at ambient temperature under dark conditions. The resulting opalescent suspension contains exfoliated titania nanosheets (TNS; 1.4 g/L, pH = 11~12).

3. Synthesis of TNS Films21

  1. Preparation of TNS cast films (c-TNS)
    1. Pre-clean glass substrates (~20 x 20 mm2) through ultrasonic treatments using an ultrasonic cleaner (27 kHz) in 1 M aqueous sodium hydroxide (NaOH) for 30 min.
    2. Rinse the substrates with 5-10 mL of ultrapure water (<0.056 µS cm-1).
    3. Dip a glass substrate in a 0.1 M aqueous hydrochloric acid (HCl) for 3 min and rinse with 5-10 ml of ultrapure water.
    4. Clean the substrates through ultrasonic treatments (27 kHz) in pure water for 1 hr, and then rinse with pure water. Dry with a hairdryer for 2-3 min (until dry).
    5. Cast the colloidal suspension of TNS on the glass substrate in 300 µl aliquots.
    6. Dry at 60 °C for 2 hr using a dry oven to give the c-TNS film.
  2. Preparation of Sintered TNS Film (s-TNS)
    1. To achieve thermal fixation of the TNS components on the glass substrate (s-TNS film), sinter the obtained c-TNS film in air at 500 °C for 3 hr (heating from 25 to 500 °C at a rate of 6.8 °C/min) using the oven.
    2. Repeat the sintering process twice.
  3. Preparation of Films
    1. When the s-TNS films are immersed in solution, position the deposited s-TNS film so that it faces the top for all experimental procedures.
    2. Carry out all experiments under dark conditions by covering the setup with aluminum foil to avoid the photoreaction of TNS.
  4. Preparation of Methyl Viologen (MV2+) Intercalated TNS Films (TNS/MV2+)
    1. Immerse an s-TNS film in an aqueous solution of MV2+ dichloride salt (0.2 mM, 3 ml) in a Petri dish for 7 h at room temperature (RT) under dark conditions.
    2. Rinse the obtained samples with ultrapure water (5-10 ml) and dry in air at 60 °C using an oven in the dark for ~1 hr.
  5. Preparation of Au(III) Intercalated TNS Films (TNS/Au(III))
    1. Immerse a TNS/MV2+ film in an aqueous solution of HAuCl4 (25 mM, 3 ml) in a Petri dish for 3 hr at RT under dark conditions.
    2. Rinse the obtained samples with ultrapure water (5-10 ml) and dry in air at 60 °C using an oven in the dark for ~1 hr.
  6. Synthesis of AuNP within the Interlayer Space of TNS Films (TNS/AuNP)
    1. Immerse a TNS/Au(III) film in an aqueous solution of NaBH4 (0.1 M, 5 ml) in a Petri dish for 0.5 hr at RT under dark conditions.
    2. Dry the obtained films in air at 60 °C using an oven in the dark for ~1 hr.
  7. Preparation of 2-AET+ Intercalated TNS Films (TNS/2-AET+)
    1. Immerse an s-TNS film in an aqueous solution of 2-AET+ Cl− (0.1 M, 3 ml) in a Petri dish for 24 hr at RT.
    2. Rinse obtained films with ultrapure water (5-10 ml) and dry in air at 60 °C using an oven in the dark for ~1 hr.
  8. Au(III) and 2-AET+ Co-Intercalated TNS Films (TNS/2-AET+/Au(III)).
    1. Immerse a TNS/2-AET+ film in an aqueous solution of HAuCl4 (25 mM, 3 ml) for 3 h at RT.
    2. Rinse the obtained films with ultrapure water (5-10 ml) and dry in air at 60 °C using an oven in the dark for ~1 hr.
  9. Synthesis of AuNP within the Interlayer Space of TNS/2-AET+ Films (TNS/2-AET+/AuNP).
    1. Immerse a TNS/2-AET+/Au(III) film in an aqueous solution of NaBH4 (0.1 M, 5 ml) in a Petri dish for 0.5 hr at RT under dark conditions.
    2. Rinse the obtained films with ultrapure water (5-10 ml) and dry in air at 60 °C using oven in the dark for ~1 hr.
  10. Characterizations
    1. Carry out X-ray diffraction (XRD) analyses21 using a desktop X-ray diffractometer with monochromatized Cu-Kα radiation (λ = 0.15405 nm), operated at 30 kV and 15 mA.
    2. Take energy dispersive X-ray spectrometry (EDS) spectra21.
    3. Employ a multichannel photodetector or steady-state ultraviolet-visible (UV-Vis) absorption spectrophotometer to record UV-Vis absorption spectra for the prepared samples using transmittance mode21.

Access restricted. Please log in or start a trial to view this content.

Results

Two types of precursor films were used in this study (i.e., with and without the protective reagent (2-AET+) within the interlayer of TNS). In the absence of 2-AET+, 1,1'-dimethyl-4,4'-bipyridinium dichloride (methyl viologen; MV2+) was used as an expander of the interlayer space, because MV2+-containing LMOSs have been frequently used as intermediates in the guest exchange method for preparing LMOSs16,17,21,33-36.

Access restricted. Please log in or start a trial to view this content.

Discussion

This manuscript provides a detailed protocol for the in situ synthesis of gold nanoparticles (AuNPs) within the interlayer space of TNS films. This is the first report of the in situ synthesis of AuNPs within the interlayer space of TNS. Moreover, we found that the 2-AET+ works as an effective protective reagent for AuNPs within the interlayer of TNS. These methods hybridized AuNPs and TNS transparent films. TNS films with good optical transparency21 were synthesized through sinter...

Access restricted. Please log in or start a trial to view this content.

Disclosures

We have nothing to disclose.

Acknowledgements

This work was partly supported by Nippon Sheet Glass Foundation for Materials Science and Engineering and JSPS KAKENHI (Grant-in-Aid for Challenging Exploratory Research, #50362281).

Access restricted. Please log in or start a trial to view this content.

Materials

NameCompanyCatalog NumberComments
Methyl viologen dichlorideAldrich Chemical  Co., Inc.1910-42-5
Tetrabutylammonium hydroxideTCIT1685
cesium carbonateKanto Chemical Co., Inc.07184-33
anatase titanium dixoideIshihara Sangyo Ltd.ST-01
hydrochloric acidJunsei Chemical Co., Ltd.20010-0350
sodium hydroxideJunsei Chemical Co., Ltd.195-13775
Tetrachloroauric(III) acid trihydrateKanto Chemical Co., Inc.17044-60
sodium tetrahydroborateJunsei Chemical Co., Ltd.39245-1210
2-ammoniumethanethiol hydrochlorideTCIA0296
Ultrapure water (0.056 µS/cm)Milli-Q water purification system (Direct-Q® 3UV, Millipore)
Microscope slide (Thickness: 1.0–1.2 mm)Matsunami glass Co., Ltd.

References

  1. Kelly, K. L., Coronado, E., Zhao, L. L., Schatz, G. C. The Optical Properties of Metal Nanoparticles: The Influence of Size, Shape, and Dielectric Environment. J. Phys. Chem. B. 107 (3), 668-677 (2003).
  2. Rycenga, M., et al. Controlling the Synthesis and Assembly of Silver Nanostructures for Plasmonic Applications. Chem. Rev. 111 (6), 3669-3712 (2011).
  3. The Binh, N., et al. Preparation of metal nanoparticles for surface enhanced Raman scattering by laser ablation method. Adv. Nat. Sci.: Nanosci. Nanotechnol. 3 (2), 025016(2012).
  4. Chen, H., Shao, L., Li, Q., Wang, J. Gold nanorods and their plasmonic properties. Chem. Soc. Rev. 42 (7), 2679-2724 (2013).
  5. Subramanian, V., Wolf, E. E., Kamat, P. V. Influence of Metal/Metal Ion Concentration on the Photocatalytic Activity of TiO2-Au Composite Nanoparticles. Langmuir. 19 (2), 469-474 (2003).
  6. Linic, S., Christopher, P., Ingram, D. B. Plasmonic-metal nanostructures for efficient conversion of solar to chemical energy. Nat Mater. 10 (12), 911-921 (2011).
  7. Gomes Silva, C., Juárez, R., Marino, T., Molinari, R., García, H. Influence of Excitation Wavelength (UV or Visible Light) on the Photocatalytic Activity of Titania Containing Gold Nanoparticles for the Generation of Hydrogen or Oxygen from Water. J. Am. Chem. Soc. 133 (3), 595-602 (2011).
  8. Hou, W., et al. Photocatalytic Conversion of CO2 to Hydrocarbon Fuels via Plasmon-Enhanced Absorption and Metallic Interband Transitions. ACS Catal. 1 (8), 929-936 (2011).
  9. Wang, W. -N., et al. Size and Structure Matter: Enhanced CO2 Photoreduction Efficiency by Size-Resolved Ultrafine Pt Nanoparticles on TiO2 Single Crystals. J. Am. Chem. Soc. 134 (27), 11276-11281 (2012).
  10. Shi, X., Ueno, K., Takabayashi, N., Misawa, H. Plasmon-Enhanced Photocurrent Generation and Water Oxidation with a Gold Nanoisland-Loaded Titanium Dioxide Photoelectrode. J. Phys. Chem. C. 117 (6), 2494-2499 (2013).
  11. Tanaka, A., Sakaguchi, S., Hashimoto, K., Kominami, H. Preparation of Au/TiO2 with Metal Cocatalysts Exhibiting Strong Surface Plasmon Resonance Effective for Photoinduced Hydrogen Formation under Irradiation of Visible Light. ACS Catal. 3 (1), 79-85 (2013).
  12. Bian, Z., Tachikawa, T., Zhang, P., Fujitsuka, M., Majima, T. Au/TiO2 Superstructure-Based Plasmonic Photocatalysts Exhibiting Efficient Charge Separation and Unprecedented Activity. J. Am. Chem. Soc. 136 (1), 458-465 (2014).
  13. Ide, Y., et al. Hybridization of Au nanoparticle-loaded TiO2 with BN nanosheets for efficient solar-driven photocatalysis. J. Mater. Chem. A. 2 (12), 4150-4156 (2014).
  14. Zheng, Z., Tachikawa, T., Majima, T. Plasmon-induced spatial electron transfer between single Au nanorods and ALD-coated TiO2: dependence on TiO2 thickness. Chem. Commun. 51 (76), 14373-14376 (2015).
  15. Inui, Y., et al. Reversible redox processes of poly(anilines) in layered semiconductor niobate films under alternate UV-Vis light illumination. J. Phys. Chem. B. 111 (42), 12162-12169 (2007).
  16. Yui, T., Takagi, K. Bottom-up Nanofabrication Vol. 5. Ariga, K., Nalwa, H. S. 5, American Scientific Publishers. Ch. 2 35-90 (2009).
  17. Nalwa, H. S. Encyclopedia of Nanoscience and Nanotechnology Vol. 24. , American Scientific Publishers. 303-361 (2011).
  18. Yui, T., et al. Visible light-induced electron transfers in titania nanosheet and mesoporous silica integrated films. Bull. Chem. Soc. Jpn. 79 (3), 386-396 (2006).
  19. Yui, T., et al. Photoinduced one-electron reduction of MV2+ in titania nanosheets using porphyrin in mesoporous silica thin films. Langmuir. 21 (7), 2644-2646 (2005).
  20. Yui, T., et al. Remarkably stabilized charge separations in inorganic nanospace. Bull. Chem. Soc. Jpn. 82 (7), 914-916 (2009).
  21. Sasaki, K., et al. Synthesis of copper nanoparticles within the interlayer space of titania nanosheet transparent films. J. Mater. Chem. C. 4 (7), 1476-1481 (2016).
  22. Sasaki, T., Komatsu, Y., Fujiki, Y. A new layered hydrous titanium dioxide HTi2 -/4O4[middle dot]H2O. J. Chem. Soc., Chem. Commun. (12), 817-818 (1991).
  23. Sasaki, T., Watanabe, M. Osmotic Swelling to Exfoliation. Exceptionally High Degrees of Hydration of a Layered Titanate. J. Am. Chem. Soc. 120 (19), 4682-4689 (1998).
  24. Yui, T., et al. Synthesis of photofunctional titania nanosheets by electrophoretic deposition. Chem. Mater. 17 (1), 206-211 (2005).
  25. Tachikawa, T., Yui, T., Fujitsuka, M., Takagi, K., Majima, T. Photocatalytic electron transfer in hybrid titania nanosheets studied by nanosecond laser flash photolysis. Chem. Lett. 34 (11), 1522-1523 (2005).
  26. Zhou, Y., Ma, R., Ebina, Y., Takada, K., Sasaki, T. Multilayer Hybrid Films of Titania Semiconductor Nanosheet and Silver Metal Fabricated via Layer-by-Layer Self-Assembly and Subsequent UV Irradiation. Chem. Mater. 18 (5), 1235-1239 (2006).
  27. Yui, T., et al. Photochemical electron transfer though the interface of hybrid films of titania nano-sheets and mono-dispersed spherical mesoporous silica particles. Phys. Chem. Chem. Phys. 8 (39), 4585-4590 (2006).
  28. Sakai, N., Sasaki, T., Matsubara, K., Tatsuma, T. Layer-by-layer assembly of gold nanoparticles with titania nanosheets: control of plasmon resonance and photovoltaic properties. J. Mater. Chem. 20 (21), 4371-4378 (2010).
  29. Yui, T., et al. Photoinduced Electron Transfer between the Anionic Porphyrins and Viologens in Titania Nanosheets and Monodisperse Mesoporous Silica Hybrid Films. ACS Appl. Mater. Interfaces. 3 (4), 931-935 (2011).
  30. Wang, L., Sasaki, T. Titanium Oxide Nanosheets: Graphene Analogues with Versatile Functionalities. Chem. Rev. 114 (19), 9455-9486 (2014).
  31. Eguchi, M., Ito, M., Ishibashi, T. -a Stabilization and Modification of Gold Nanocube Surfaces with Layered Silicate. Chem. Lett. 43 (1), 140-142 (2014).
  32. Fujimura, T., Yoshida, Y., Inoue, H., Shimada, T., Takagi, S. Dense Deposition of Gold Nanoclusters Utilizing a Porphyrin/Inorganic Layered Material Complex as the Template. Langmuir. 31 (33), 9142-9147 (2015).
  33. Tong, Z., Shichi, T., Takagi, K. Visible-Light Induced Charge-Separation between Consecutively Cast Porphyrin and Methyl Viologen Multilayered Titanoniobate Hybrid Films. J. Phys. Chem. B. 106 (51), 13306-13310 (2002).
  34. Tong, Z., Shichi, T., Oshika, K., Takagi, K. A Nanostructured Hybrid Material Synthesized by the Intercalation of Porphyrin into Layered Titanoniobate. Chem. Lett. 31 (9), 876-877 (2002).
  35. Tong, Z., Takagi, S., Tachibana, H., Takagi, K., Inoue, H. Novel Soft Chemical Method for Optically Transparent Ru(bpy)3-K4Nb6O17 Thin Film. J. Phys. Chem. B. 109 (46), 21612-21617 (2005).
  36. Hattori, T., et al. Hybridization of layered niobates with cationic dyes. Res. Chem. Intermed. 32 (7), 653-669 (2006).
  37. Moreau, F., Bond, G. C., Taylor, A. O. Gold on titania catalysts for the oxidation of carbon monoxide: control of pH during preparation with various gold contents. J. Catal. 231 (1), 105-114 (2005).
  38. Ivanova, S., Petit, C., Pitchon, V. A new preparation method for the formation of gold nanoparticles on an oxide support. Appl. Cat. A. 267 (1-2), 191-201 (2004).
  39. Sasaki, T., Watanabe, M., Hashizume, H., Yamada, H., Nakazawa, H. Macromolecule-like Aspects for a Colloidal Suspension of an Exfoliated Titanate. Pairwise Association of Nanosheets and Dynamic Reassembling Process Initiated from It. J. Am. Chem. Soc. 118 (35), 8329-8335 (1996).
  40. Tanaka, T., Ebina, Y., Takada, K., Kurashima, K., Sasaki, T. Oversized Titania Nanosheet Crystallites Derived from Flux-Grown Layered Titanate Single Crystals. Chem. Mater. 15 (18), 3564-3568 (2003).
  41. Denkikagaku Binran, 5th edn. , Maruzen. (2000).
  42. Shannon, R. D. Revised effective ionic radii and systematic studies of interatomic distances in halides and chalcogenides. Acta Cryst. 32, 751-767 (1976).
  43. Jia, Y. Q. Crystal radii and effective ionic radii of the rare earth ions. J. Solid State Chem. 95 (1), 184-187 (1991).
  44. Grabar, K. C., Freeman, R. G., Hommer, M. B., Natan, M. J. Preparation and Characterization of Au Colloid Monolayers. Anal. Chem. 67 (4), 735-743 (1995).
  45. Niidome, T., Nakashima, K., Takahashi, H., Niidome, Y. Preparation of primary amine-modified gold nanoparticles and their transfection ability into cultivated cells. Chem. Commun. (17), 1978-1979 (2004).
  46. Kawano, T., Horiguchi, Y., Niidome, Y., Niidome, T., Yamada, S. Preparation of Cationic Gold Nanoparticle in Aqueous Solutions of 2-Aminoethanethiol Hydrochloride. Bunseki Kagaku. 54 (6), 521-526 (2005).
  47. Tong, Z., Shichi, T., Kasuga, Y., Takagi, K. The Synthesis of Two Types of Layered Niobate Hybrid Materials by the Selective Intercalation of Ionic Porphyrin. Chem. Lett. 31 (12), 1206-1207 (2002).
  48. Zhao, S., Chen, S., Wang, S., Quan, Z. Composite Au/TiO2 Nanoparticles: Synthesis, Characterization, and Assembly by Using Potentiostatic Technique. J. Colloid Interface Sci. 221 (2), 161-165 (2000).
  49. Negishi, Y., Nobusada, K., Tsukuda, T. Glutathione-Protected Gold Clusters Revisited: Bridging the Gap between Gold(I)-Thiolate Complexes and Thiolate-Protected Gold Nanocrystals. J. Am. Chem. Soc. 127 (14), 5261-5270 (2005).
  50. Schmidt-Stein, F., et al. X-ray induced photocatalysis on TiO2 and TiO2 nanotubes: Degradation of organics and drug release. Electrochem. Commun. 11 (11), 2077-2080 (2009).
  51. Tamura, K., et al. X-ray induced photoelectrochemistry on TiO2. Electrochim. Acta. 52 (24), 6938-6942 (2007).

Access restricted. Please log in or start a trial to view this content.

Reprints and Permissions

Request permission to reuse the text or figures of this JoVE article

Request Permission

Explore More Articles

Gold NanoparticlesLayered TitanateTransparent FilmsNanostructured HybridsMetal NanoparticlesRadial SemiconductorsPigmentsDyesCatalystsPhotocatalystsNanostructuresIn Situ SynthesisMethyl ViologenTetrachloroauric AcidSodium Borohydride

This article has been published

Video Coming Soon

JoVE Logo

Privacy

Terms of Use

Policies

Contact Us

Recommend to library

JoVE NEWSLETTERS

Research

Education

Authors

Librarians

ABOUT JoVE

Copyright © 2025 MyJoVE Corporation. All rights reserved