Microfluidic Dry-spinning and Characterization of Regenerated Silk Fibroin Fibers

Summary

A protocol for the microfluidic spinning and microstructure characterization of regenerated silk fibroin monofilament is presented.

Abstract

The protocol demonstrates a method for mimicking the spinning process of silkworm. In the native spinning process, the contracting spinning duct enables the silk proteins to be compact and ordered by shearing and elongation forces. Here, a biomimetic microfluidic channel was designed to mimic the specific geometry of the spinning duct of the silkworm. Regenerated silk fibroin (RSF) spinning doped with high concentration, was extruded through the microchannel to dry-spin fibers at ambient temperature and pressure. In the post-treated process, the as-spun fibers were drawn and stored in ethanol aqueous solution. Synchrotron radiation wide-angle X-ray diffraction (SR-WAXD) technology was used to investigate the microstructure of single RSF fibers, which were fixed to a sample holder with the RSF fiber axis normal to the microbeam of the X-ray. The crystallinity, crystallite size, and crystalline orientation of the fiber were calculated from the WAXD data. The diffraction arcs near the equator of the two-dimensional WAXD pattern indicate that the post-treated RSF fiber has a high orientation degree.

Introduction

Spider and silkworm can produce outstanding silk fiber from aqueous protein solution at ambient temperature and pressure. Shearing and extensional flow can induce the formation of liquid crystal texture in the silk gland¹. In recent years, there has been a great interest in mimicking the spinning process of the spider in order to produce high strength artificial fibers. However, large quantities of spider silk protein cannot be produced efficiently and economically by farming spiders due to cannibalism. Substantial amounts of silkworm silk can be obtained easily by farming. Otherwise, the silkworm and spider have a similar spinning process and amino acid composition. Therefore, silkworm silk fibroin is selected as a substitute to spin artificial animal silk by many researchers.

Spider and silkworm extrude protein solution through their spinning duct into fiber in air. The high stress forces generated along the spinning duct most likely stretch the silk fibroin molecules to a more extended conformation². Artificial silk fibers have been spun using conventional wet spinning and dry-spinning processes^3,4, which do not take into account the fluid forces generated in the spinning duct.

First, microfluidic approaches were used to investigate the assembly of silk protein^5,6. Then, microfluidic fabrication of RSF was studied via modeling the shearing and extensional forces^7,8. Young's modulus and diameter of RSF fibers can be tuned by microfluidic wet spinning, but the tensile strength of drawn fiber was less than 100 MPa⁷. Finally, high strength RSF fibers were successfully prepared using the microfluidic dry-spinning method, but the diameter of the fiber is only 2 µm⁸. Recently, microfluidic wet spinning was successfully used in the production of high strength recombinant spider silk fiber. The post-spinning drawing in air improved the surface and internal defects of artificial fiber⁹.

In this study, the improved microfluidic spinning process for RSF fiber is introduced. It aims to mimic the spinning process of silkworm silk, including the spinning dope, shearing forces, and dry-spinning process. This spinning method not only can produce high strength artificial silk fiber, but also can adjust the diameter of the fiber. Firstly, the RSF spinning dope was sheared and elongated in a biomimic channel with a second order exponential decay. Secondly, the influences of relative humidity (RH) on the fiber morphology and properties were studied in the microfluidic dry-spinning process¹⁰. Compared to the conventional spinning spinneret, our microfluidic system is highly biomimetic and can be used to produce high strength fiber from solutions at ambient temperature by the dry or wet spinning method.

Due to the high-resolution, high-brightness, and high-energy of the synchrotron radiation microfocus X-ray, it can be used to characterize the microstructure of a single fiber with a diameter of several micrometers^{4,11,12,13,14}. Here, SR-WAXD technique was used to calculate the crystallinity, crystallite size and crystalline orientation of RSF fibers.

Protocol

CAUTION: Please consult all relevant material safety data sheets before use. Several of the chemicals used in preparing the molding are acutely toxic. Please use personal protective equipment (safety glasses, gloves, lab coat, full length pants, and closed-toe shoes).

1. Microfluidic Spinning of RSF Aqueous Solution

1. Preparation of RSF aqueous spinning dope^4,15,16
   1. Degumming of silkworm cocoon
      1. Degum the Bombyx mori cocoons twice in Na₂CO₃ aqueous solutions (0.5 wt% in water) at 100 °C for 30 min each, and then wash the silk with deionized water to remove the sericin.
   2. Dissolving of degummed silkworm cocoon
      1. Dry the degummed cocoon silks in air; then dissolve the degummed cocoon silks in 9.0 M LiBr aqueous solution with a ratio of 1:10 (w/v) at 40 °C for 2 h. For example, add 10 mL LiBr per 1 gram silk (Figure 1a).
   3. Centrifuging and filtering
      1. Dilute the RSF solution 1.5 times by deionized water. Centrifuge and filter to remove impurities. Centrifuge the RSF solution in 250 mL bottles at 4 °C for 10 min at 1,234.8 x g. Filter the RSF solution using a 20 µm filter and a vacuum pump. Double filter paper bed is preferable considering the experimentation effect.
   4. Dialyzing
      1. Dialyze the RSF solution in deionized water at 5 °C for 3 days using a cellulose semipermeable membrane (MWCO: 14,000 ± 2,000). The total volume of RSF solution is about 1 L, loaded in 4 dialysis bags. Put these dialysis bags in the bucket, which is filled with 10 L reverse osmosis (RO) deionized water.
         NOTE: The pH value of deionized water should be higher than 6, to avoid gelation during the concentration process. The pH of deionized water did not require adjustment for this protocol.
   5. Concentrating
      1. Condense the RSF aqueous solution to 20 wt% by forced airflow at 5 °C. Add 3 M CaCl₂ aqueous solution into the RSF solution to 1.0 mmol/g Ca²⁺ final concentration; then concentrate by forced air flow to 38-47 wt%.
      2. Weigh one drop of RSF solution on a glass slide and then dry it for 2 h in an oven at 105 °C.
         NOTE: The weight percent of the remaining solid compared to the weight of the drop before drying is the total concentration of protein and CaCl₂. The RSF concentration is derived after deduction of the mass of CaCl₂. At least four repeated measurements were performed. Our previous studies showed that the concentration of Ca²⁺ greatly affected the rheological properties and spinnability of the RSF aqueous solutions. Meanwhile, the addition of Ca²⁺ prompted the limited formation of β-sheet and the aggregation of RSF¹⁷. In a native spinning dope, CaCl₂ is considered to play an important role during the storage of spinning dope to avoid gelation before spinning.¹⁸
2. Preparation of microfluidic chip^8,19
   1. Preparing photomask
      1. Design the micro-channel in a CAD program. Print the CAD file to produce a high-resolution transparency¹⁹.
   2. Preparing the mold
      1. Cleaning the glass slide
         1. In a chemical hood, boil the glass slide in the mixed solution of concentrated sulfuric acid and 30 vol% hydrogen peroxide solution (10:1) for 20 min on a hot plate.
            CAUTION: Sulfuric acid and hydrogen peroxide vapors are extremely toxic.
      2. Washing the glass slide
         1. Wash the glass slide using deionized water, and blow dry with high purity nitrogen.
      3. Coating film
         1. Coat the SU-8 photoresist on the glass slide by a custom-built coating device with a gap of 100 µm between the bottom surface of the coating bar and the upper surface of glass.
      4. Spin coating
         1. Spread the photoresist on the glass slide to form a uniform film using a spin coater at 40.3 x g for 30 s. The thickness of the uniform film is about 85 µm.
      5. Solidification
         1. Solidify the photoresist in an oven with a temperature controlling program. Elevate the temperature from room temperature to 65 °C at 2 °C/min and hold at 65 °C for 2 min. Continue to heat up from 65 °C to 95°C and hold at 95 °C for 15 min. Turn off the oven and cool down naturally to room temperature in the oven.
      6. Ultraviolet light exposure
         1. Expose the side of glass slide with the photoresist to ultraviolet light for 12 s using the transparency as a photomask by photolithography¹⁹.
            NOTE: The wavenumber of the ultraviolet light is 365 nm and the exposure energy is 273.6 mJ/cm².
            CAUTION: Take proper safety measure while working with UV light and the oven.
      7. Solidify the photoresist as described in step 1.2.2.5.
      8. Developing
         1. Clean the photoresist ultrasonically in developer solution for 30 s. Wash the glass slide by isopropanol and developer, alternating between the two, until there is no precipitation on the glass slide.
      9. Solidify the photoresist in an oven with a temperature controlling program. Elevate the temperature from room temperature to 170 °C at 2 °C/min and hold at 170 °C for 30 min. Turn off the oven and cool down naturally to room temperature in the oven.
   3. Soft lithography
      1. Pour 8.8 g liquid polydimethylsiloxane (PDMS) pre-polymer over the mold and cure for 30 min at 65 °C, and 15 min at 80 °C. Liquid PDMS pre-polymer consists of PDMS and curing agent (typically at 10:1 (w/w)).
   4. Punching
      1. Punch a hole through the PDMS replica at the beginning of the channel by drill. The diameter of the drill is 1.2 mm.
   5. Sealing
      1. Seal the PDMS replica with the channel to a flat PDMS layer without pattern by an oxygen plasma treatment on the surfaces of the two PDMS layers.
         NOTE: The overall preparation process of the chip takes about 72 h.
3. Fabrication of RSF fiber
   1. Injection of spinning dope
      1. Inject the RSF spinning dope into the microchannel at 2 µL/min by a syringe pump.
   2. Environment regulation
      1. Adjust the relative humidity to 40 ± 5 RH% or 50 ± 5 RH% using a humidifier. At 40 ± 5 RH%, as-spun fiber solidified more quickly than 50 ± 5 RH%.
   3. Production of RSF fiber
      1. Touch the RSF drop by a pinpoint at the outlet of the microfluidic channel, draw RSF fiber into air, and then reel it onto a roller through a 10-cm air gap at a speed of 3 cm/s (Figure 1b).
   4. Store the RSF fibers in a sealed desiccator for 24 h.
   5. Fiber post-treatment
      1. Draw the as-spun fibers 4 times at 0.9 mm s^-1 in 80 vol% ethanol solution by a custom-built machine, and then keep the drawn fiber fixed and immerse the fibers in the solution for 1 h. Because of this treatment, the length of the fiber was changed from originally 15 mm to 60 mm.
   6. Preparing the sample for characterization
      1. Fix the post-treated fibers on a paper frame with a 10-mm gauge length. At least 20 fibers are need for measurement, including in the tensile test, SEM, FTIR, and WAXS. The diameters of the post-drawn fibers range from 5 to 10 µm. Figure 1 shows the schematic of the fiber production and WAXD characterization. The mechanical properties of the RSF fibers were examined by a material testing system at (25 ± 2) °C and (45 ± 5)% relative humidity. The extension rate and gauge length were 2 mm/min and 1 cm, respectively.

2. Synchrotron Radiation Characterization of Crystalline Structure of RSF Fiber

1. Synchrotron radiation characterization^4,13,17
   1. Adjustment of beamline
      1. Adjust the wavelength of the X-rays and spot size to 0.07746 nm and 3 x 2 µm², respectively.
         NOTE: The protocol is performed using the BL15U1 beamline at the Shanghai Synchrotron Radiation Facility.
   2. Location of the X-ray spot
      1. Find the location of the X-ray spot.
         NOTE: The location of the X-ray spot is adjusted by the laboratory technician at the Synchrotron Radiation Facility.
   3. Testing of standard sample: Cerium dioxide (CeO₂)
      1. Test a standard sample CeO₂ powder. The CeO₂ powder was characterized to calculate the circle center and the distance from the sample to the detector.
   4. Sample preparation
      1. Fix the RSF filaments in parallel with each other on the paper frame with a 10 mm gauge length. Glue the paper frame on the testing stage.
         NOTE: Keep the fiber horizontal.
   5. SR-WAXD testing
      1. Open the shutter
         1. Close the door of the beamline station after ensuring that there are no persons in the room. Open the shutter of X-ray beam source.
      2. Focusing
         1. Move the fiber slightly until in focus. Adjust the location of fiber along the x, y, z direction remotely via a software (Figure 1c).
      3. Sample exposure
         1. Move the fiber up and down remotely via a software, until it is on the X-ray spot. Press the start button on the software to expose the fiber to the X-ray beamline for 20 s (Figure 1c).
      4. Background diffraction
         1. Test the diffraction of the air background with the exposure time of 20 s. Move the fiber away from the X-ray spot remotely via a software. Press the "start" button on the software to expose the X-ray beamline to "air medium" for 20 s.
2. SR-WAXD data processing¹³
   1. Software calibration
      1. Process the WAXD data using FIT2D (V12.077). Calibrate the circle center and the distance of sample-to-detector using the diffraction data of the CeO₂ powder.
   2. 2-D diffraction pattern
      1. Subtract the air background from the fiber diffraction pattern using FIT2D (V12.077).
   3. Crystallinity and crystallite size
      1. Integrate the diffraction intensity as a function of scattering angle 2θ. Perform deconvolution of the intensity integration by automated peak separation software (Version 4.12)¹². The degree of crystallinity, x_c, was estimated from the relation:
         
         , where I_c is the sum of the integrated intensities of the crystalline peaks and I_a is the integrated intensity of the amorphous halo^4,11. The integration of the WAXD patterns showed the peak width of the [200], [020], [002] reflections. The FWHM of these peaks were used to determine the crystallite size along the a, b, and c axes by using Scherrer's formula⁴.
   4. Determination of the crystallite orientations
      1. Calculate the orientations of the crystallite and amorphous according to azimuthal integrations of (020) and (210) peaks¹¹. The crystalline orientation can be calculated quantitatively according to Herman's orientation. Here, both (020) and (210) peaks were fitted with two Gaussian functions. The narrower one is for crystalline orientation and the other broader one is for the oriented amorphous material¹³. Here, the crystallite orientations of RSF fibers were compared using the full width at half maximum (FWHM) of azimuthal integrations (002) peaks.

Results

High strength RSF fibers were successfully produced by using the microfluidic spinning method. The stress-strain curves and SEM images of the stretched RSF fibers C44R40 are shown in Figure 2. At least 10 fibers were measured in the tensile test. Stress-strain curves were chosen according to the average value of the breaking stress and strain of fibers. The WAXD data of the fibers are shown in Figure 3. The crystallinity and crys...

Discussion

During the dialysis of the RSF solution, the pH value is critical for the following concentration process. If the pH value of the deionized water is smaller than 6, the RSF solution will be easier to gel during the concentration process. To avoid gelation, CaCl₂ is added to the RSF solution. The concentration of CaCl₂ is 1 mmol per weight of RSF.

Our previous work demonstrated the possibility of microfluidic dry-spinning of an RSF aqueous solution⁸...

Materials

Name	Company	Catalog Number	Comments
B. mori Cocoons	Farmer in Tongxiang, Zhejiang Province, China
Sodium carbonate, anhydrous, 99.8%	Shanghai Lingfeng Chemical Reagent Co., Ltd., China		Analytically Pure
Lithium bromide, 99.1%	Shanghai China Lithium Industrial Co., Ltd., China		Analytically Pure
Calcium chloride, anhydrous, 96.0%	Shanghai Lingfeng Chemical Reagent Co., Ltd., China		Analytically Pure
Ethanol, anhydrous, 99.7%	Sinopharm Group Chemical Reagent Co.,Ltd., China	10009218	Analytically Pure
SU-8 photoresist	MicroChem Corp., USA
Developing solution	MicroChem Corp., USA
Sylgard 184	Dow Corning, USA
Isopropanol	Shanghai Lingfeng Chemical Reagent Co., Ltd., China		Analytically Pure
Concentrated sulfuric acid	Pinghu Chemical Reagent Factory, China		Analytically Pure
30 vol% hydrogen peroxide	Shanghai Jinlu Chemical reagent Co., Ltd., China		Analytically Pure
Acetone	Shanghai Zhengxing Chemical Reagent Factory, China		Analytically Pure
Oxygen plasma treatment	DT-01, Suzhou Omega Machinery Electronic Technology Co., Ltd., China
Syringe pump	KD Scientific, USA		KDS 200P
Humidifier	SEN electric
Driller	Hangzhou Bo Yang Machinery Co., Ltd., China		bench drilling machine Z406c
Material testing system	Instron, USA		Model: 5565
PeakFit	Systat Software, Inc., USA		Version 4.12