This work was supported by the National Natural Science Foundation of China (Grant Number. 82174506).

This study was approved by the ethics committee of Yueyang Hospital, affiliated with Shanghai University of Traditional Chinese Medicine (reference no. 2021-062), and each participant signed an informed consent form.
1. Experiment preparations
<ol>
	<li>Camera settings:
	<ol>
		<li>Place three tripods in front of the operation table, and connect them with three cameras.</li>
		<li>Set the shooting parameters of the cameras as follows: resolution 1280 x720 pixels, format MP4, full manual mode (M), aperture F1.2, shutter 1/1000s, ISO 6400, automatic white balance, optical zoom 0mm. 
		NOTE: The angle between every two cameras is required to be set at 60&#176;-120&#176; (Figure 1A).</li>
	</ol>
	</li>
	<li>Tracking marker placement:
	<ol>
		<li>Attach seven reflective balls with a diameter of 6.5 mm on the holding-needle hand of each participant for video recording as detailed in steps 1.2.2-1.2.4 and shown in Figure 2A.</li>
		<li>Wrist: Attach one ball on the midpoint of the ulna and radial styloid defined as tracking point &#34;wrist joint &#34;(WJ)</li>
		<li>Thumb: Attach one ball each on the center of thumb nail defined as tracking point &#34;thumb tip&#34; (TT), the IP joint defined as tracking point &#34;thumb end joint&#34; (TEJ), and the metacarpophalangeal (MCP) joint defined as tracking point &#34;thumb base joint&#34; (TBJ), respectively.</li>
		<li>Forefinger: Attach one ball each on the center of the forefinger nail defined as tracking point &#34;forefinger tip&#34; (FT), the proximal interphalangeal (PIP) joint defined as tracking point &#34;forefinger middle joint&#34; (FMJ), and the MCP joint defined as tracking point &#34;forefinger base joint&#34; (FBJ), respectively.</li>
	</ol>
	</li>
</ol>
2. Video shooting and editing
<ol>
	<li>Place a small 15 cm x 15 cm x 15 cm 3D calibration frame with 8 points on the operating table for 3D calibration (Figure 1B,C).</li>
	<li>Remove the frame from the table after taking a video of the calibration frame for at least 8 s.</li>
	<li>Instruct the participants to perform AM on the acupuncture point LI11 (Quchi) of the volunteer, including lifting-thrusting and twirling skills, to control the needle to move up and down and rotate with thumb and forefinger, respectively. Take the videos of the above skills for at least 10 cycles. 
	NOTE: The inclusion and exclusion criteria of the participants to perform AM and volunteers to provide acupuncture points for needling are listed. Participant inclusion: (1) acupuncture teacher or student finished the &#34;lifting-thrusting skill&#34; and &#34;twirling skill&#34; chapter in the course textbook entitled &#39;Acupuncture and Moxibustion Techniques and Manipulations19; (2) participant should have hands-on needling experience with the human body for more than 5 times. Participant exclusion: (1) non-acupuncture teachers or students; (2) acupuncture students without any hands-on needling experience with the human body. Volunteer inclusion: (1) age between 16-60 years old; (2) no obvious skin damage, rupture, suppuration or obvious exudation around LI11 on the right arm. Volunteer exclusion: (1) individuals with a history of smoking, alcohol or drug abuse; (2) individuals with blood system diseases or obvious bleeding tendency; (3) individuals with chronic mental illness or mental disorders; (4) pregnant women; (5) individuals with a history of fainting needles.</li>
	<li>Export all the videos from the cameras to the designated disk of the computer. Rename the 3D calibration videos in cameras 1, 2, 3 as &#34;ca-1.mp4&#34;, &#34;ca-2.mp4&#34; and &#34;ca-3.mp4&#34;.</li>
	<li>Synchronize all manipulation videos in the video editing software (e.g., Adobe premiere pro) and export them named as &#34;lifting-thrusting-1.avi&#34;, &#34;lifting-thrusting-2.avi&#34;, &#34;lifting-thrusting-3.avi&#34;, &#34;twirling-1.avi&#34;, &#34;twirling-2.avi&#34; and &#34;twirling-3.avi&#34;, respectively. 
	&#8203;NOTE: Refer to Supplementary File 1 for the video synchronization instructions of the video editing software used in this study.</li>
</ol>
3. Project configuration of Simi Reality Motion System (motion capture and analysis software)
<ol>
	<li>Open the motion capture and analysis software and choose Create a New Project. Set the project name in Project Label and click Create and Save to save the project in the designated disk.</li>
	<li>Choose Specification &#62; Points &#62; Right/Left Hand and drag the above tracking points from the Predefined Points box into the Used Points box, then click on the Close button to continue. 
	NOTE: All the following steps take the tracking points of the right hand as an example.</li>
	<li>Choose Specification &#62; Connections and click on New Connection
	<ol>
		<li>Input connection name &#34;forefinger III right&#34;. Select &#34;forefinger middle joint right&#34; as the Starting Point and Line to the point &#34;forefinger tip right&#34; in the same window</li>
		<li>Click on the Apply and Close buttons to finish the establishment of the connection.</li>
	</ol>
	</li>
	<li>Add and rename the camera groups
	<ol>
		<li>Right-click on Cameras &#62; Add Camera Group to add new camera groups.</li>
		<li>Right-click on Cameras &#62; Rename to rename the camera groups as &#34;lifting-thrusting camera group&#34; and &#34;twirling camera group&#34;, respectively.</li>
	</ol>
	</li>
	<li>Right-click on the Lifting-Thrusting Camera Group &#62; Add Camera
	<ol>
		<li>Click on the Select File button in the Tracking box.</li>
		<li>Click on Open Existing File and select the operation video &#34;lifting-thrusting-1.avi&#34; in the next window, then click on Apply to finish video import.</li>
		<li>Similar to the above actions, click on Select File in the 3D Calibration box, and import the corresponding calibration video &#34;ca-1.mp4&#34;.</li>
	</ol>
	</li>
	<li>According to step 3.5, continue to import the operation videos &#34;lifting-thrusting-2.avi&#34; and &#34;lifting-thrusting-3.avi&#34;, and their corresponding calibration videos &#34;ca-2.mp4&#34; and &#34;ca-3.mp4&#34; in the Lifting-Thrusting Camera Group, respectively. 
	NOTE: There should be 3 cameras in the Lifting-Thrusting Camera Group in the project window after sections 3.4 and 3.5.</li>
	<li>According to steps 3.4, 3.5, and 3.6, import the twirling skill and calibration videos into the Twirling Camera Group.</li>
</ol>
4. Video analysis
<ol>
	<li>3D calibration for each camera
	<ol>
		<li>Expand Lifting-Thrusting Camera Group and right-click on Lifting-Thrusting-1 &#62; Properties.</li>
		<li>Click on the 3D Calibration button in the 3D Calibration box; input the description and add 8 points by clicking on Add Point button for 8 times</li>
		<li>Click on Apply after setting the name and corresponding X, Y, Z value for each point according to the calibration parameters (Table 1).</li>
		<li>After configuring all points, move the mouse to click each endpoint of the calibration video to finish the 3D calibration.</li>
		<li>Follow steps 4.1.1-4.1.4 to complete the 3D calibration of the other cameras in the same group and the cameras in the Twirling Camera Group.</li>
	</ol>
	</li>
	<li>3D finger motion tracking
	<ol>
		<li>Right-click on Lifting-Thrusting Camera Group &#62; 3D Tracking, select all the cameras, and click on the OK button to open the 3D tracking window.</li>
		<li>Set the Track Using Pattern Matching (all points) for all the cameras and manually click on all the tracking points in the first frame.</li>
		<li>Click on the Search Automatically button to start automatic 3D tracking frame by frame.</li>
		<li>Follow steps 4.2.1-4.2.3 to complete the motion tracking of the Twirling Camera Group. 
		NOTE: If a tracking point is lost during the automatic 3D tracking, select the lost point line, right-click on Discard Point From Here, then re-click the point and the Search Automatically button. Select Yes if the message &#34;No start frame for tracking has been set for 3 selected camera(s). it can be set individually in camera properties. Do you want to set start frame to frame 0 for all cameras without start frame and continue now?&#34; pops up.</li>
	</ol>
	</li>
	<li>Data export
	<ol>
		<li>Right-click on Lifting-Thrusting Camera Group &#62; New 3D Calculation, select all the cameras, and check Update Data Continuously and Store Data Explicitly in File in Create 3D Data window. Click the OK button to continue.</li>
		<li>Right-click on the folder Lifting-Thrusting-3D Coordinates Data &#62; Export, check Column Headings, Tracking Names, Start Time and Frequency, Time Information in First Column, X, Y, Z, v(X), v(Y), v(Z) in the Export window</li>
		<li>Click the Export button to export the data file (*.txt) with the customized name. Export the data file of the Twirling Camera Group in the same way.</li>
	</ol>
	</li>
</ol>
5. Data analysis
NOTE: An original PHP script is used to browse and analyze the data files exported by the motion capture and analysis software. All the source code has been shared in a GitHub repository20.
<ol>
	<li>After the data files exported from the motion capture and analysis software are uploaded to a specific server folder running this script, open the script and input the Username and Password to log in.</li>
	<li>Click on Add New Participant, select the Participant Type and Gender, and input the Participant Name, Age, and Practice Time in the pop-up page; click on Submit to finish adding a new participant.</li>
	<li>Click on Add New Record corresponding to the newly added participant in the list page, then input the Folder Name containing the uploaded data files of the motion capture and analysis software and select the Operation Date; click on Submit to continue.</li>
	<li>Click on Analysis corresponding to the newly added operation record, then select Skill and click on Submit. The script will identify and display all the valid crests and troughs for manual review. 
	NOTE: A certain crest or trough can be reselected manually in the corresponding drop-down list if the script incorrectly identifies it. Based on these crests and troughs, the average values of amplitudes and velocities along three axes of each tracking point and the operating time of lifting, thrusting, twirling left, and twirling right actions can be calculated and displayed by the script. The calculation method of these parameters is shown in Figure 3.</li>
</ol>

<ol>
	<li>Xu, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+different+twirling+and+rotating+acupuncture+manipulation+techniques+on+the+blood+flow+perfusion+at+acupoints.">Effect of different twirling and rotating acupuncture manipulation techniques on the blood flow perfusion at acupoints.</a> Journal of Traditional Chinese Medicine. 39 (5), 730-739 (2019).</li><li>Lan, K. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+the+New+Lift-Thrust+Operation+in+Laser+Acupuncture+Investigated+by+Thermal+Imaging.">Effects of the New Lift-Thrust Operation in Laser Acupuncture Investigated by Thermal Imaging.</a> Evidence-Based Complementary and Alternative Medicine. 2019 (2), 1-8 (2019).</li><li>Zhang, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+acupuncture+with+needle+manipulation+at+different+frequencies+for+patients+with+hypertension:+Result+of+a+24-+week+clinical+observation.">Effects of acupuncture with needle manipulation at different frequencies for patients with hypertension: Result of a 24- week clinical observation.</a> Complementary Therapies in Medicine. 45, 142-148 (2019).</li><li>Sun, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Correlation+between+acupuncture+dose+and+effectiveness+in+the+treatment+of+knee+osteoarthritis:+a+systematic+review.">Correlation between acupuncture dose and effectiveness in the treatment of knee osteoarthritis: a systematic review.</a> Acupuncture in Medicine. 37 (5), 261-267 (2019).</li><li>Choi, Y. J., Lee, J. E., Moon, W. K., Cho, S. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Does+the+effect+of+acupuncture+depend+on+needling+sensation+and+manipulation.">Does the effect of acupuncture depend on needling sensation and manipulation.</a> Complementary Therapies in Medicine. 21 (3), 207-214 (2013).</li><li>Park, Y. J., Lee, J. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+acupuncture+intervention+and+manipulation+types+on+poststroke+dysarthria:+A+systematic+review+and+meta-analysis.">Effect of acupuncture intervention and manipulation types on poststroke dysarthria: A systematic review and meta-analysis.</a> Evidence-Based Complementary and Alternative Medicine. 2020, 4981945 (2020).</li><li>Yang, N. N., Ma, S. M., Yang, J. W., Li, T. R., Liu, C. Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Standardizing+therapeutic+parameters+of+acupuncture+in+vascular+dementia+rats.">Standardizing therapeutic parameters of acupuncture in vascular dementia rats.</a> Brain and Behavior. 10 (10), 01781 (2020).</li><li>Lyu, R., Gao, M., Yang, H., Wen, Z., Tang, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Stimulation+parameters+of+manual+acupuncture+and+their+measurement.">Stimulation parameters of manual acupuncture and their measurement.</a> Evidence-Based Complementary and Alternative Medicine. 2019, 1725936 (2019).</li><li>Li, J., Grierson, L. E., Wu, M. X., Breuer, R., Carnahan, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Perceptual+motor+features+of+expert+acupuncture+lifting-thrusting+skills.">Perceptual motor features of expert acupuncture lifting-thrusting skills.</a> Acupuncture in Medicine. 31 (2), 172-177 (2013).</li><li>Xuemin, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Application+of+Twirling+Replenishing+and+Reducing+Technique+and+Its+Quantitative+Concept.">Application of Twirling Replenishing and Reducing Technique and Its Quantitative Concept.</a> Chinese Medical Journal. 05, 16-17 (1987).</li><li>Guxing, <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+teaching+test+apparatus+for+acupuncture+manipulations+in+TCM.">Development of teaching test apparatus for acupuncture manipulations in TCM.</a> Chinese Acupuncture &amp; Moxibustion. 21 (4), 229 (2001).</li><li>Liu, T. Y., Yang, H. Y., Li, X. J., Kuai, L., Gao, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Exploitation+and+application+of+acupuncture+manipulation+information+analysis+system.">Exploitation and application of acupuncture manipulation information analysis system.</a> Zhen Ci Yan Jiu. 33 (5), 330-333 (2008).</li><li>Leow, M. Q., Cao, T., Cui, S. L., Tay, S. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantifying+needle+motion+during+acupuncture:+implications+for+education+and+future+research.">Quantifying needle motion during acupuncture: implications for education and future research.</a> Acupuncture in Medicine. 34 (6), 482-484 (2016).</li><li>Sun, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Research on Acupuncture Information Transmission and Quantification System. , (2005).</li><li>Tang, W. C., Yang, H. Y., Liu, T. Y., Gao, M., Xu, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Motion+video-based+quantitative+analysis+of+the+'lifting-thrusting'+method:+a+comparison+between+teachers+and+students+of+acupuncture.">Motion video-based quantitative analysis of the 'lifting-thrusting' method: a comparison between teachers and students of acupuncture.</a> Acupuncture in Medicine. 36 (1), 21-28 (2018).</li><li>Zhang, A., Yan, X. K., Liu, A. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Introduction+to+a+newly-developed+“Acupuncture+Needle+Manipulation+Training-evaluation+System”+based+on+optical+motion+capture+technique.">An Introduction to a newly-developed “Acupuncture Needle Manipulation Training-evaluation System” based on optical motion capture technique.</a> Acupuncture Research. 41 (6), 556-559 (2016).</li><li>Zhang, A., Yan, X. K., Liu, A. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Introduction+to+A+Newly-developed+“Acupuncture+Needle+Manipulation+Training-evaluation+System”+[Based+on+Optical+Motion+Capture+Techniqu].">An Introduction to A Newly-developed “Acupuncture Needle Manipulation Training-evaluation System” [Based on Optical Motion Capture Techniqu].</a> Zhen Ci Yan Jiu. 41 (6), 556-559 (2016).</li><li>Yang, P., Sun, X. W., Ma, Y. K., Zhang, C. X., Zhang, W. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+research+on+acupuncture+manipulation+based+on+video+motion+capture.">Quantitative research on acupuncture manipulation based on video motion capture.</a> Medical Biomechanics. 31 (2), 154-159 (2016).</li><li>Wang, F. C., Ma, T. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Acupuncture and Moxibustion Techniques and Manipulations, 4 end. , 31-34 (2016).</li><li>. Acupuncture Manipulation Analysis (AMA) Version 1.1 Available from: <a target="_blank" href="https://github.com/SHUTCM-tcme/AMA">https://github.com/SHUTCM-tcme/AMA</a> (2021)</li><li>Wu, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ISB+recommendation+on+definitions+of+joint+coordinate+systems+of+various+joints+for+the+reporting+of+human+joint+motion--Part+II:+shoulder,+elbow,+wrist+and+hand.">ISB recommendation on definitions of joint coordinate systems of various joints for the reporting of human joint motion--Part II: shoulder, elbow, wrist and hand.</a> Journal of Biomechanics. 38 (5), 981-992 (2005).</li><li>Metcalf, C. D., Notley, S. V., Chappell, P. H., Burridge, J. H., Yule, V. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Validation+and+application+of+a+computational+model+for+wrist+and+hand+movements+using+surface+markers.">Validation and application of a computational model for wrist and hand movements using surface markers.</a> IEEE Transactions on Biomedical Engineering. 55 (3), 1199-1210 (2008).</li><li>Ganguly, A., Rashidi, G., Mombaur, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+the+performance+of+the+leap+motion+controller(tm)+with+a+standard+marker-based+motion+capture+system.">Comparison of the performance of the leap motion controller(tm) with a standard marker-based motion capture system.</a> Sensors (Basel). 21 (5), (2021).</li><li>Cecilio-Fernandes, D., Cnossen, F., Coster, J., Jaarsma, A. D. C., Tio, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effects+of+expert+and+augmented+feedback+on+learning+a+complex+medical+skill.">The effects of expert and augmented feedback on learning a complex medical skill.</a> Perceptual and Motor Skills. 127 (4), 766-784 (2020).</li><li>Asadipour, A., Debattista, K., Chalmers, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Visuohaptic+augmented+feedback+for+enhancing+motor+skills+acquisition.">Visuohaptic augmented feedback for enhancing motor skills acquisition.</a> The Visual Computer. 33 (4), 401-411 (2017).</li><li>Ozkaya, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+motion+capture+data+during+repetitive+overarm+throwing+practice.">Three-dimensional motion capture data during repetitive overarm throwing practice.</a> Scientific Data. 5, 180272 (2018).</li><li>Maidhof, C., Kastner, T., Makkonen, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Combining+EEG,+MIDI,+and+motion+capture+techniques+for+investigating+musical+performance.">Combining EEG, MIDI, and motion capture techniques for investigating musical performance.</a> Behavior Research Methods. 46 (1), 185-195 (2014).</li><li>Turner, C., Visentin, P., Oye, D., Rathwell, S., Shan, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Pursuing+artful+movement+science+in+music+performance:+single+subject+motor+analysis+with+two+elite+pianists.">Pursuing artful movement science in music performance: single subject motor analysis with two elite pianists.</a> Perceptual and Motor Skills. 128 (3), 1252-1274 (2021).</li><li>Holden, M. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Objective+assessment+of+colonoscope+manipulation+skills+in+colonoscopy+training.">Objective assessment of colonoscope manipulation skills in colonoscopy training.</a> International Journal for Computer Assisted Radiology and Surgery. 13 (1), 105-114 (2018).</li><li>Oquendo, Y. A., Riddle, E. W., Hiller, D., Blinman, T. A., Kuchenbecker, K. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Automatically+rating+trainee+skill+at+a+pediatric+laparoscopic+suturing+task.">Automatically rating trainee skill at a pediatric laparoscopic suturing task.</a> Surgical Endoscopy. 32 (4), 1840-1857 (2018).</li><li>Kwak, J. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Improvement+of+arthroscopic+surgical+performance+using+a+new+wide-angle+arthroscope+in+the+surgical+training.">Improvement of arthroscopic surgical performance using a new wide-angle arthroscope in the surgical training.</a> PLoS One. 14 (3), 0203578 (2019).</li><li>Zhenzhu, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Feasibility+study+of+the+low-cost+motion+tracking+system+for+assessing+endoscope+holding+skills.">Feasibility study of the low-cost motion tracking system for assessing endoscope holding skills.</a> World Neurosurgery. 140, 312-319 (2020).</li><li>Sakakura, Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biomechanical+profiles+of+tracheal+intubation:+a+mannequin-based+study+to+make+an+objective+assessment+of+clinical+skills+by+expert+anesthesiologists+and+novice+residents.">Biomechanical profiles of tracheal intubation: a mannequin-based study to make an objective assessment of clinical skills by expert anesthesiologists and novice residents.</a> BMC Medical Education. 18 (1), 293 (2018).</li><li>Hunukumbure, A. D., Smith, S. F., Das, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Holistic+feedback+approach+with+video+and+peer+discussion+under+teacher+supervision.">Holistic feedback approach with video and peer discussion under teacher supervision.</a> BMC Medical Education. 17 (1), 179 (2017).</li></ol>

The authors have nothing to disclose.

This study established the measurement method of the kinematic parameters of AM in vivo and obtained the data of motion amplitude, velocity, and operation time of the six important tracking points on the thumb and forefinger along three axes. Meanwhile, based on the 3D calibration frame, a 3D stick view and corresponding animation of the thumb and forefinger during needling were generated. The thumb and forefinger movement of AM can be fully displayed with the synchronous playback of kinematic parameter curve an...

As a kind of the clinical skills of traditional Chinese medicine (TCM) and physical stimulation, acupuncture manipulation (AM) is often regarded as an important factor that affects the therapeutic effect of acupuncture1,2. Many studies have confirmed that different AM or different stimulation parameters (needling velocity, amplitude, frequency, etc.) of the same AM resulted in different therapeutic effects3,4,5,6,7. Therefore, the measurement of relevant kinematic parameters of AM and correlation analysis with the therapeutic effect can provide useful data support and reference for the clinical treatment with acupuncture8,9.
The measurement of kinematic parameters of the AM began in the 1980s10. In the early days, the electrical signal conversion technology based on variable resistance was mainly used to convert the displacement signal of the needle body into a voltage or current signal for displaying and recording the amplitude and frequency data of AM11. Moreover, the famous ATP-II Chinese medicine acupuncture technique tester II (ATP-II) with this technology currently has been used by many traditional Chinese medicine universities of China12. After that, with the continuous development and innovation of sensor technology, different types of sensors were used to collect kinematic parameters of AM. For example, the three axes electromagnetic motion sensor was attached to the needle handle to acquire needling amplitude and velocity13; the bioelectric signal sensor was placed on the dorsal horn of the animal&#39;s spinal cord to record needling frequency14, etc. Although the quantitative research of AM based on the above two types of technologies has completed the acquisition of relevant kinematic parameters during needling, its main disadvantages are the inability to perform the real-time non-invasive measurement and the change of operating feel caused by the modification of the needle body.
In recent years, motion tracking technology was gradually applied to the quantitative research of AM15,16. Because it is based on the frame-by-frame analysis of needling video, the measurement of acupuncture parameters can be acquired during in vivo operation without modifying the needle body. This technology has been used to measure the kinematic parameters such as amplitude, velocity, acceleration, and frequency of four tracking points of thumb and forefinger during needling in a two-dimensional (2D) plane and established the corresponding finger stick figure15. Some studies also measured the angle change range of interphalangeal (IP) joint of thumb and forefinger with similar technology9,17,18. However, the current studies on AM analysis are still mainly limited to the 2D motion plane, and the number of tracking points is relatively small. So far, there is no complete three-dimensional (3D) kinematics measurement and analysis method for AM, and no related data was published.
To solve the above problems, this study will use 3D motion tracking technology to measure the kinematic parameters of the seven tracking points of hand during needling. This protocol aims to provide a complete technical solution for the kinematic analysis on AM, as well as the further study on the dose-effect correlation of acupuncture.

<table><tbody><tr><td>3D calibration frame</td><td>Any brand</td><td></td><td>15 x 15 x 15 cm</td></tr><tr><td>Acupuncture needles</td><td>Suzhou Medical Appliance Factory</td><td></td><td>0.35 x 40 mm</td></tr><tr><td>Double-sided tape</td><td>Any brand</td><td></td><td>Round, 1 cm-diameter</td></tr><tr><td>Reflective balls</td><td>Simi Reality Motion Systems GmbH</td><td></td><td>6.5 mm-diameter</td></tr><tr><td>SD card</td><td>Western Digital Corporation</td><td></td><td>SDXC UHS-I</td></tr><tr><td>SD card reader</td><td>UGREEN Group Limited</td><td></td><td>USB 3.0</td></tr><tr><td>Simi Motion</td><td>Simi Reality Motion Systems GmbH</td><td></td><td>Ver.8.5.15</td></tr><tr><td>Swab</td><td>Any brand</td><td></td><td>The volume fraction of ethanol is 70%-80%</td></tr><tr><td>Three cameras</td><td>Victor Company of Japan, Limited</td><td></td><td>JVC GC-PX100BAC</td></tr><tr><td>Three tripods</td><td>Any brand</td><td></td><td></td></tr></tbody></table>

three-dimensional finger motion tracking during needling: a solution for the kinematic analysis of acupuncture manipulation

Three-dimensional (3D) motion tracking has been used in many fields, such as the researches of sport and medical skills. This experiment aimed to use 3D motion tracking technology to measure the kinematic parameters of the joints of fingers during acupuncture manipulation (AM) and establish three technical indicators "amplitude, velocity and time". This method can reflect the operation characteristics of AM and provide quantitative parameters along three axes of multiple finger joints. The current evidence shows that the method has great potential for future applications such as the study of the dose-effect relationship of acupuncture, teaching, and learning of AM, and the measurement and preservation of famous acupuncturists' AM.

After establishing this experimental method, the lifting-thrusting and twirling skills of basic AM of nineteen acupuncture teachers from the School of Acupuncture-Moxibustion and Tuina of Shanghai University of TCM were measured using 3D motion tracking. According to the definition of a joint coordinate system (JCS) for the shoulder, elbow, wrist, and hand proposed by the Standardization and Terminology Committee (STC) of the International Society of Biomechanics21, seven finger tracking points ha...

Watch this Scientific Journal Video about Three-Dimensional Finger Motion Tracking during Needling: A Solution for the Kinematic Analysis of Acupuncture Manipulation at JoVE.com

Three-Dimensional Finger Motion Tracking during Needling: A Solution for the Kinematic Analysis of Acupuncture Manipulation

This experimental method describes a solution for the kinematic analysis of acupuncture manipulation with three-dimensional finger motion tracking technology.

Three-dimensional (3D) motion tracking has been used in many fields, such as the researches of sport and medical skills. This experiment aimed to use 3D ...

three-dimensional-finger-motion-tracking-during-needling-solution-for

Research

JoVE Journal

Medicine

2.7K Views.  Shanghai University of Traditional Chinese Medicine. This experimental method describes a solution for the kinematic analysis of acupuncture manipulation with three-dimensional finger motion tracking technology.

Video: Three-Dimensional Finger Motion Tracking during Needling: A Solution for the Kinematic Analysis of Acupuncture Manipulation

Visualizing Motion Patterns in Acupuncture Manipulation

Acupuncture manipulation varies widely among practitioners in clinical settings, and it is difficult to teach novice students how to perform acupuncture manipulation techniques skillfully. The Acupuncture Manipulation Education System (AMES) is an open source software system designed to enhance acupuncture manipulation skills using visual feedback. Using a phantom acupoint and motion sensor, our method for acupuncture manipulation training provides visual feedback regarding the actual movement of the student's acupuncture manipulation in addition to the optimal or intended movement, regardless of whether the manipulation skill is lifting, thrusting, or rotating. Our results show that students could enhance their manipulation skills by training using this method. This video shows the process of manufacturing phantom acupoints and discusses several issues that may require the attention of individuals interested in creating phantom acupoints or operating this system.

Here, we present a protocol for using the Acupuncture Manipulation Education System (AMES) in the training of acupuncture manipulation skills using phantom acupoints.

Acupuncture manipulation varies widely among practitioners in clinical settings, and it is difficult to teach novice students how to perform acupuncture ...

Behavior

Heterotypic Three-dimensional In Vitro Modeling of Stromal-Epithelial Interactions During Ovarian Cancer Initiation and Progression

Epithelial ovarian cancers (EOCs) are the leading cause of death from gynecological malignancy in Western societies. Despite advances in surgical treatments and improved platinum-based chemotherapies, there has been little improvement in EOC survival rates for more than four decades 1,2. Whilst stage I tumors have 5-year survival rates &gt;85%, survival rates for stage III/IV disease are &lt;40%. Thus, the high rates of mortality for EOC could be significantly decreased if tumors were detected at earlier, more treatable, stages 3-5. At present, the molecular genetic and biological basis of early stage disease development is poorly understood. More specifically, little is known about the role of the microenvironment during tumor initiation; but known risk factors for EOCs (e.g. age and parity) suggest that the microenvironment plays a key role in the early genesis of EOCs. We therefore developed three-dimensional heterotypic models of both the normal ovary and of early stage ovarian cancers. For the normal ovary, we co-cultured normal ovarian surface epithelial (IOSE) and normal stromal fibroblast (INOF)&nbsp;cells, immortalized by retrovrial transduction of the catalytic subunit of human telomerase holoenzyme (hTERT) to extend the lifespan of these cells in culture. To model the earliest stages of ovarian epithelial cell transformation, overexpression of the CMYC oncogene in IOSE cells, again co-cultured with INOF cells. These heterotypic models were used to investigate the effects of aging and senescence on the transformation and invasion of epithelial cells. Here we describe the methodological steps in development of these three-dimensional model; these methodologies aren't specific to the development of normal ovary and ovarian cancer tissues, and could be used to study other tissue types where stromal and epithelial cell interactions are a fundamental aspect of the tissue maintenance and disease development.

Heterotypic Three-dimensional In Vitro Modeling of Stromal-Epithelial Interactions During Ovarian Cancer Initiation and Progression

We describe methodologies for establishing in vitro heterotypic three-dimensional models comprising ovarian fibroblasts and normal ovarian surface or ovarian cancer epithelial cells. We discuss the use of these models to study stromal-epithelial interactions that occur during ovarian cancer development.

Epithelial ovarian cancers (EOCs) are the leading cause of death from gynecological malignancy in Western societies. Despite advances in surgical ...

Frame-by-Frame Video Analysis of Idiosyncratic Reach-to-Grasp Movements in Humans

Prehension, the act of reaching to grasp an object, is central to the human experience. We use it to feed ourselves, groom ourselves, and manipulate objects and tools in our environment. Such behaviors are impaired by many sensorimotor disorders, yet our current understanding of their neural control is far from complete. Current technologies for investigating human reach-to-grasp movements often utilize motion tracking systems that can be expensive, require the attachment of markers or sensors to the hands, impede natural movement and sensory feedback, and provide kinematic output that can be difficult to interpret. While generally effective for studying the stereotypical reach-to-grasp movements of healthy sighted adults, many of these technologies face additional limitations when attempting to study the unpredictable and idiosyncratic reach-to-grasp movements of young infants, unsighted adults, and patients with neurological disorders. Thus, we present a novel, inexpensive, and highly reliable yet flexible protocol for quantifying the temporal and kinematic structure of idiosyncratic reach-to-grasp movements in humans. High speed video cameras capture multiple views of the reach-to-grasp movement. Frame-by-frame video analysis is then used to document the timing and magnitude of pre-defined behavioral events such as movement start, collection, maximum height, peak aperture, first contact, and final grasp. The temporal structure of the movement is reconstructed by documenting the relative frame number of each event while the kinematic structure of the hand is quantified using the ruler or measure function in photo editing software to calibrate 2 dimensional linear distances between two body parts or between a body part and the target. Frame-by-frame video analysis can provide a quantitative and comprehensive description of idiosyncratic reach-to-grasp movements and will enable researchers to expand their area of investigation to include a greater range of naturalistic prehensile behaviors, guided by a wider variety of sensory modalities, in both healthy and clinical populations.

This protocol describes how to use frame-by-frame video analysis to quantify idiosyncratic reach-to-grasp movements in humans. A comparative analysis of reaching in sighted versus unsighted healthy adults is used to demonstrate the technique, but the method can also be applied to the study of developmental and clinical populations.

Prehension, the act of reaching to grasp an object, is central to the human experience. We use it to feed ourselves, groom ourselves, and manipulate ...

Three-Dimensional Ultrasonic Needle Tip Tracking with a Fiber-Optic Ultrasound Receiver

Ultrasound is frequently used for guiding minimally invasive procedures, but visualizing medical devices is often challenging with this imaging modality. When visualization is lost, the medical device can cause trauma to critical tissue structures. Here, a method to track the needle tip during ultrasound image-guided procedures is presented. This method involves the use of a fiber-optic ultrasound receiver that is affixed within the cannula of a medical needle to communicate ultrasonically with the external ultrasound probe. This custom probe comprises a central transducer element array and side element arrays. In addition to conventional two-dimensional (2D) B-mode ultrasound imaging provided by the central array, three-dimensional (3D) needle tip tracking is provided by the side arrays. For B-mode ultrasound imaging, a standard transmit-receive sequence with electronic beamforming is performed. For ultrasonic tracking, Golay-coded ultrasound transmissions from the 4 side arrays are received by the hydrophone sensor, and subsequently the received signals are decoded to identify the needle tip&#39;s spatial location with respect to the ultrasound imaging probe. As a preliminary validation of this method, insertions of the needle/hydrophone pair were performed in clinically realistic contexts. This novel ultrasound imaging/tracking method is compatible with current clinical workflow, and it provides reliable device tracking during in-plane and out-of-plane needle insertions.

Accurate and efficient visualization of invasive medical devices is extremely important in many ultrasound-guided minimally invasive procedures. Here, a method for localizing the spatial position of a needle tip relative to the ultrasound imaging probe is presented.

Ultrasound is frequently used for guiding minimally invasive procedures, but visualizing medical devices is often challenging with this imaging modality. ...

Engineering

Estimation of Contact Regions Between Hands and Objects During Human Multi-Digit Grasping

To grasp an object successfully, we must select appropriate contact regions for our hands on the surface of the object. However, identifying such regions is challenging. This paper describes a workflow to estimate the contact regions from marker-based tracking data. Participants grasp real objects, while we track the 3D position of both the objects and the hand, including the fingers' joints. We first determine the joint Euler angles from a selection of tracked markers positioned on the back of the hand. Then, we use state-of-the-art hand mesh reconstruction algorithms to generate a mesh model of the participant's hand in the current pose and the 3D position. 
Using objects that were either 3D printed or 3D scanned-and are, thus, available as both real objects and mesh data-allows the hand and object meshes to be co-registered. In turn, this allows the estimation of approximate contact regions by calculating the intersections between the hand mesh and the co-registered 3D object mesh. The method may be used to estimate where and how humans grasp objects under a variety of conditions. Therefore, the method could be of interest to researchers studying visual and haptic perception, motor control, human-computer interaction in virtual and augmented reality, and robotics.

When we grasp an object, multiple regions of the fingers and hand typically make contact with the object's surface. Reconstructing such contact regions is challenging. Here, we present a method for approximately estimating the contact regions by combining marker-based motion capture with existing deep learning-based hand mesh reconstruction.

To grasp an object successfully, we must select appropriate contact regions for our hands on the surface of the object. However, identifying such regions ...

Four-Dimensional CT Analysis Using Sequential 3D-3D Registration

Four-dimensional computed tomography (4DCT) provides a series of volume data and visualizes joint motions. However, numerical analysis of 4DCT data remains difficult because segmentation in all volumetric frames is time-consuming. We aimed to analyze joint kinematics using a sequential 3D-3D registration technique to provide the kinematics of the moving bone with respect to the fixed bone semiautomatically using 4DCT DICOM data and existing software. Surface data of the source bones are reconstructed from 3DCT. The trimmed surface data are respectively matched with surface data from the first frame in 4DCT. These trimmed surfaces are sequentially matched until the last frame. These processes provide positional information for target bones in all frames of the 4DCT. Once the coordinate systems of the target bones are decided, translation and rotation angles between any two bones can be calculated. This 4DCT analysis offers advantages in kinematic analyses of complex structures such as carpal or tarsal bones. However, fast or large-scale motions cannot be traced because of motion artifacts.

We analyzed joint kinematics from four-dimensional computed tomography data. The sequential 3D-3D registration method semiautomatically provides the kinematics of the moving bone with respect to the subject bone from four-dimensional computed tomography data.

Four-dimensional computed tomography (4DCT) provides a series of volume data and visualizes joint motions. However, numerical analysis of 4DCT data ...

Bioengineering

3D Kinematic Analysis for the Functional Evaluation in the Rat Model of Sciatic Nerve Crush Injury

Compared to the Sciatic Functional Index (SFI), kinematic analysis is a more reliable and sensitive method for performing functional evaluations of sciatic nerve injury rodent models. In this protocol, we describe a novel kinematic analysis method that uses a three-dimensional (3D) motion capture apparatus for functional evaluations using a rat sciatic nerve crush injury model. First, the rat is familiarized with treadmill walking. Markers are then attached to the designated bone landmarks and the rat is made to walk on the treadmill at the desired speed. Meanwhile, the posterior limb movements of the rat are recorded using four cameras. Depending on the software used, marker tracings are created using both automatic and manual modes and the desired data are produced after subtle adjustments. This method of kinematic analysis, which uses a 3D motion capture apparatus, offers numerous advantages, including superior precision and accuracy. Many more parameters can be investigated during the comprehensive functional evaluations. This method has several shortcomings that require consideration: The system is expensive, can be complicated to operate, and may produce data deviations due to skin shifting. Nevertheless, kinematic analysis using a 3D motion capture apparatus is useful for performing functional anterior and posterior limb evaluations. In the future, this method may become increasingly useful for generating accurate assessments of various traumas and diseases.

We introduce a kinematic analysis method that uses a three-dimensional motion capture apparatus containing four cameras and data processing software for performing functional evaluations during fundamental research involving rodent models.

Compared to the Sciatic Functional Index (SFI), kinematic analysis is a more reliable and sensitive method for performing functional evaluations of ...

Neuroscience

Capturing Dynamic Finger Gesturing with High-resolution Surface Electromyography and Computer Vision

Finger gestures are a critical element in human communication, and as such, finger gesture recognition is widely studied as a human-computer interface for state-of-the-art prosthetics and optimized rehabilitation. Surface electromyography (sEMG), in conjunction with deep learning methods, is considered a promising method in this domain. However, current methods often rely on cumbersome recording setups and the identification of static hand positions, limiting their effectiveness in real-world applications. The protocol we report here presents an advanced approach combining a wearable surface EMG and finger&#160;tracking system to capture comprehensive data during dynamic hand movements. The method records muscle activity from soft printed electrode arrays (16 electrodes) placed on the forearm as subjects perform gestures in different hand positions and during movement. Visual instructions prompt subjects to perform specific gestures while EMG and finger positions are recorded. The integration of synchronized EMG recordings and finger tracking data enables comprehensive analysis of muscle activity patterns and corresponding gestures. The reported approach demonstrates the potential of combining EMG and visual tracking technologies as an important resource for developing intuitive and responsive gesture recognition systems with applications in prosthetics, rehabilitation, and interactive technologies. This protocol aims to guide researchers and practitioners, fostering further innovation and application of gesture recognition in dynamic and real-world scenarios.

The paper presents a comprehensive protocol for simultaneously recording hand-electromyography (EMG) and visual finger tracking during natural finger gesturing. The visual data is designed to serve as the ground truth for the development of accurate EMG-based computational models for finger gesture recognition.

Finger gestures are a critical element in human communication, and as such, finger gesture recognition is widely studied as a human-computer interface for ...

Control Cannula Improves Precision and Stability in Acupuncture Manipulation

A Mechanical Construction to Enhance the Stability and Safety of Lifting and Thrusting Manipulation of Acupuncture

The therapeutic effectiveness of acupuncture relies on both safety and stability, making these factors essential in acupuncture manipulation research. However, manual manipulation introduces unavoidable inaccuracies, which can impact the reliability of research findings. To address this challenge, a unique lifting and thrusting manipulation control cannula was designed in this study, offering flexible adjustment of movement amplitude. The cannula was created using 3D printing technology, and its effectiveness in maintaining stability was verified by recording the acupuncture needle's movement range with optical sensor technology. The study's results show that the control cannula significantly enhances the stability of acupuncture manipulation, reducing human error. This innovation suggests that the cannula could serve as a valuable auxiliary tool for ensuring both the precision and safety of acupuncture-related experimental research. Its adoption could also contribute to the standardization of acupuncture practices, ensuring more consistent and accurate research outcomes, which is essential for future advancements in acupuncture research and clinical applications.

Author Spotlight: Development of a Standardized Acupuncture Tool Inspired by Advanced Techniques for Improved Safety and Precision

This protocol designs a cannula that can be used to control the range of motion for the lifting and thrusting manipulation in acupuncture, thereby improving stability and safety. It can thus serve both the clinical application and scientific research of acupuncture treatment.

The therapeutic effectiveness of acupuncture relies on both safety and stability, making these factors essential in acupuncture manipulation research. ...

Preliminary Study on Acupuncture Combined with Grain-sized Moxibustion for Treating Rheumatoid Arthritis with Finger Joint Pain

Most patients with rheumatoid arthritis (RA) often start with pain and swelling in the joints of the extremities, especially the small joints of the hands. At present, the etiology of RA remains unclear, and its pathological process is difficult to control. In clinical treatment, Western medicine mostly uses non-steroidal anti-inflammatory drugs (NSAIDs), disease-modifying anti-rheumatic drugs (DMARDs), glucocorticoids, biologics, etc. While they can alleviate local joint symptoms and reduce inflammatory responses, long-term use may cause significant adverse effects and high costs. In recent years, there has been an increasing application of external Traditional Chinese Medicine (TCM) therapies for treating RA, with a growing number of related studies. In this study, we observed acupuncture combined with grain-sized moxibustion in the treatment of RA with finger joint pain, assessed the changes in tender joint counts (TJC), duration of morning stiffness, the visual analog scale (VAS), erythrocyte sedimentation rate (ESR) and C-reactive protein (CRP) level of the patients before and after treatment. The results indicated that acupuncture combined with grain-sized moxibustion was more effective in reducing finger joint pain compared to therapy with simple basic medication for treating RA. Guided by the theory of syndrome differentiation in TCM, this therapy exerts its effects primarily through the stimulation of acupoints and warmth. It offers advantages such as safety, simplicity, ease of operation, precise targeting, and low price, which makes it expected to become a potential complementary therapy to relieve finger joint pain associated with RA and further improve the quality of life for RA patients. The purpose of this study is to provide a standardized operational reference for treating RA with finger joint pain by acupuncture combined with grain-sized moxibustion based on the clinical trial.

Based on the clinical trial, this study provides a standardized operational reference for treating RA with finger joint pain through acupuncture combined with grain-sized moxibustion by stimulating acupoints and warming. It can be used as an effective complementary therapy for RA pain management due to its efficacy and advantages.

Most patients with rheumatoid arthritis (RA) often start with pain and swelling in the joints of the extremities, especially the small joints of the ...

Three-Dimensional Finger Motion Tracking during Needling: A Solution for the Kinematic Analysis of Acupuncture Manipulation

Summary

Explore More Videos

Chapters in this video

Visualizing Motion Patterns in Acupuncture Manipulation

Heterotypic Three-dimensional In Vitro Modeling of Stromal-Epithelial Interactions During Ovarian Cancer Initiation and Progression

Frame-by-Frame Video Analysis of Idiosyncratic Reach-to-Grasp Movements in Humans

Three-Dimensional Ultrasonic Needle Tip Tracking with a Fiber-Optic Ultrasound Receiver

Estimation of Contact Regions Between Hands and Objects During Human Multi-Digit Grasping

Four-Dimensional CT Analysis Using Sequential 3D-3D Registration

3D Kinematic Analysis for the Functional Evaluation in the Rat Model of Sciatic Nerve Crush Injury

Capturing Dynamic Finger Gesturing with High-resolution Surface Electromyography and Computer Vision

A Mechanical Construction to Enhance the Stability and Safety of Lifting and Thrusting Manipulation of Acupuncture

Preliminary Study on Acupuncture Combined with Grain-sized Moxibustion for Treating Rheumatoid Arthritis with Finger Joint Pain