This project was supported by grants NIH NIGMS 8P41 GM103540-28 and P50-GM076516

1，样品制备<ol><li>保持在使用补充有10％胎牛血清和100 IU / ml青霉素链霉素50微克/毫升的组织培养瓶中的CHOK1细胞。培养细胞在5％二氧化碳培养箱在37℃。 </li><li>嘉实然后板CHOK1细胞在14毫米直径的微孔与0.16毫米的表面厚度。种子细胞用于成像的最佳密度，周围60-70％汇合。 </li><li>过夜孵育细胞，在37℃，5％CO 2。在HBSS（汉克缓冲盐溶液）中含有50nM的Lysotracker DND26绿色和150纳米的微管蛋白的跟踪绿色的溶液中洗涤细胞三次，并孵育细胞。孵育细胞1小时，在37℃。可选步骤：孵化前，用线粒体基质染色的染料（25纳米）执行额外的污点。 </li><li>在HBSS洗涤细胞三次，以除去任何未结合的染料。前IMAG加入新鲜的DMEM培养基荷兰国际集团的细胞。 </li></ol> 2，显微镜配置显微镜在视频协议中描述的粒子跟踪组装市售的倒置显微镜（ 图4）的框架上。三维轨道粒子跟踪然而商业模块现已上市。 <ol><li>使用相干变色龙超二钛萨飞秒激光激发光源，与690之间的NM-1040 nm的可调输出波长范围。 </li><li>确保激光束在显微镜的后部端口使用的IR-涂覆的镜子对准。激光束被使用旋转半波片之后是方解石线性偏振衰减。衰减的光束，使得在样本的平均功率为0.5〜2毫瓦。 注：该激光束由一对检流计电机致动反射镜，使在样品平面中聚焦光束的位置和轨迹的控制反映。在典型配置的准直激光束出射的检流计反射镜被扩展（10X）穿过光束扩展器，在短通分色镜反射后进入显微镜物镜的后前。 </li><li>通过将高数值孔径物镜水（60X，NA 1.2）插入光路收集来自样品的荧光的光。根据在一个或两个信道配置所需的发光波长选择在荧光滤光块。采用发射带通滤波器，以进一步选择所发射的荧光的光谱范围。 </li><li>将样品放置到电动阶段，并调整显微镜物镜的使用目的压电控制器的微调。 </li><li>直接从过滤立方体进入光电倍增管信号在那里被歧视，送到数字I / O数据采集卡的光。 注：电脑产生的波形是I / O卡的模拟输出，并provid编辑的扫描仪控制电子设备。从光电倍增管和输出信号提供给扫描仪的光子计数输入被测量，并且经由I / O卡的实验室荧光动力学SimFCS软件控制。 </li></ol> 3，影像学<ol><li>定位在舞台上的细胞，并集中使用透射光照明。 </li><li>切换到光栅扫描成像，以确定已将染料的细胞，以可视化的底层微管。确定初始区域囊泡运动存在。 </li><li>一旦分离的囊泡被识别时，设定为轨道跟踪参数如下： <ol><li>选择的轨道半径，根据该颗粒的大小被跟踪来定义圆形扫描的大小。对于一个点发射器，设置在轨道等于激发束以最大化灵敏度和响应的点扩散函数（PSF）的腰部的半径。 </li><li>设置轴向距离，以定义在执行本地化沿轴向的粒子位置两个轨道之间的距离。设定为1.5-3倍的PSF腰部的轴向距离。 </li><li>根据颗粒来设定使用了上各点的轨迹，这也决定了光漂白速率的时间的亮度定义的停留时间。使用10-100微秒之间的停留时间。 </li><li>点中每个轨道的数目设置为64或128，以产生轨道周期为4-32毫秒的顺序和用于确定粒子的位置提供了一个高的时间分辨率。 </li></ol></li><li>改变直流发送到反射镜，以通过光栅扫描图像中的光标选择通过图形用户界面，以围绕所述颗粒的光束偏移信号。 </li><li>首先从开关光栅成像显微镜模式，以轨道扫描跟踪。 </li><li>激活的反馈和数据收集。 </li></ol> 4 TrajectORY分析<ol><li>使用该软件，以显示在沿着轨道和在一个“强度地毯”的形式中，每个时间点的每个点所收集的荧光。沿着所述地毯收集的强度提供了与其它明亮物体的粒子之间的相互作用的信息。使用软件（在X，Y扫描仪且z -piezo的时间，即直流偏移）以及来自光电倍增管中的时间序列的形式收集的随着时间的荧光强度，以显示两个轨迹信息。 </li><li>使用时间序列的代表性和“强度地毯”的信息来选择的轨迹的兴趣只是一个区域。 </li><li>使用该软件，显示粒子轨迹的所选部分的二维投影。根据颗粒的荧光强度选择适当的控制，以颜色编码的轨迹。 </li><li>选择要显示在p选项根据荧光强度的文章轨迹在3D和彩色编码的。旋转用控制形象化沿微管的溶酶体运动的特征的轨迹在三维。 </li></ol>

<ol>
	<li>So, P. T., Dong, C. Y., Masters, B. R., Berland, K. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two+photon+excitation+fluorescence+microscopy.">Two photon excitation fluorescence microscopy.</a> Annu Rev Biomed Eng. 2, 399-429 (2000).</li><li>Dupont, A., Lamb, D. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nanoscale+three+dimensional+single+particle+tracking.">Nanoscale three dimensional single particle tracking.</a> Nanoscale. 3, 4532-4541 (2011).</li><li>Estrada, L. C., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=3D+nanometer+images+of+biological+fibers+by+directed+motion+of+gold+nanoparticles.">3D nanometer images of biological fibers by directed motion of gold nanoparticles.</a> Nano Lett. 11, 4656-4660 (2011).</li><li>Kis-Petikova, K., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Distance+measurement+by+circular+scanning+of+the+excitation+beam+in+the+two+photon+microscope.">Distance measurement by circular scanning of the excitation beam in the two photon microscope.</a> Microscopy Research and Technique. 63, 34-49 (2004).</li><li>Levi, V., Ruan, Q., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=3+D+particle+tracking+in+a+two+photon+microscope+application+to+the+study+of+molecular+dynamics+in+cells.">3 D particle tracking in a two photon microscope application to the study of molecular dynamics in cells.</a> Biophys J. 88, 2919-2928 (2005).</li><li>Lund, F. W., Wustner, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+comparison+of+single+particle+tracking+and+temporal+image+correlation+spectroscopy+for+quantitative+analysis+of+endosome+motility.">A comparison of single particle tracking and temporal image correlation spectroscopy for quantitative analysis of endosome motility.</a> Journal of Microscopy. 252, 169-188 (2013).</li><li>Nath, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Spreading+of+Neurodegenerative+Pathology+via+Neuron+to+Neuron+Transmission+of+beta+Amyloid.">Spreading of Neurodegenerative Pathology via Neuron to Neuron Transmission of beta Amyloid.</a> Journal of Neuroscience. 32, 8767-8777 (2012).</li><li>Balint, S., Vilanova, I. V., Alvarez, A. S., Lakadamyali, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Correlative+live+cell+and+superresolution+microscopy+reveals+cargo+transport+dynamics+at+microtubule+intersections.">Correlative live cell and superresolution microscopy reveals cargo transport dynamics at microtubule intersections.</a> Proceedings of the National Academy of Sciences of the United States of America. 110, 3375-3380 (2013).</li><li>Huotari, J., Helenius, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Endosome+maturation.">Endosome maturation.</a> Embo Journal. 30, 3481-3500 (2011).</li><li>Ragan, T., So, P. T., Kwon, H. S., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=3D+particle+tracking+on+the+two+photon+microscope.">3D particle tracking on the two photon microscope.</a> Multiphoton Microscopy in the Biomedical Sciences. 2, 247-258 (2001).</li><li>Konig, K., So, P. T. C., Mantulin, W. W., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cellular+response+to+near-infrared+femtosecond+laser+pulses+in+two+photon+microscopes.">Cellular response to near-infrared femtosecond laser pulses in two photon microscopes.</a> Optics Letters. 22, 135-136 (1997).</li><li>Caviston, J. P., Holzbaur, E. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microtubule+motors+at+the+intersection+of+trafficking+and+transport.">Microtubule motors at the intersection of trafficking and transport.</a> Trends Cell Biol. 16, 530-537 (2006).</li><li>Cardarelli, F., Lanzano, L., Gratton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Capturing+directed+molecular+motion+in+the+nuclear+pore+complex+of+live+cells.">Capturing directed molecular motion in the nuclear pore complex of live cells.</a> Proceedings of the National Academy of Sciences of the United States of America. 109, 9863-9868 (2012).</li></ol>

The authors have nothing to disclose.

尽管荧光显微技术及仪器，在过去几年取得的荧光粒子在三维空间运动轨迹具有高时间分辨率的巨大进步一直保持在该领域的挑战。如果高时间分辨率已经在两个维度上被实现跟踪颗粒，延伸到轴向方向通常带来大幅减少了系统10的频率响应。 在这个视频协议，我们重点跟踪单个粒子在三维空间中活的细胞中利用双光子显微镜的高时间分辨率（32毫秒在这个实验中）?...

大量方法已被开发出迄今为止为在使用显微镜的三维跟踪荧光发色粒子。大多数方法依赖于使用的快速照相机，非常适合以跟踪在两个维度上，典型地结合了镜的出射光学系统的定制修改，以实现跟踪在轴向方向上。激光扫描显微镜（或者共聚焦或两个光子）通常可以追踪的荧光粒子通过进行的Z-堆栈的时刻的顺序，尽管这种过程通常是耗时的，并且会产生合理的时间分辨率（10赫兹）只有当被跟踪的粒子是由有源反馈机制2保持在一个小的光栅成像区域的中心。 锁入到该颗粒的想法是在轨道的跟踪方法的基础。取而代之的是光栅扫描的圆形轨道围绕的荧光粒子进行。荧光沿强度轨道精确本地化粒子的位置4。 该颗粒的局部位置然后可用于致动显微镜扫描器和重新中心在粒子位置的轨道。显微镜的检流计扫描仪是由一个模拟电压驱动。这个电压的AC分量允许用聚焦激光束进行的轨道， 即正弦波和施加到X和Y扫描反射镜将允许执行一个圆形轨道上的余弦波。直流信号的偏移有助于改变轨道中心的位置。一旦一个轨道期间被确定并且对于交流信号的波形构成，所述反馈系统需要更新信号的唯一的直流分量。 软件能够读取从检测器收集到的荧光信号是必需的，以控制扫描仪和检测器，来计算粒子的位置和更新的直流断设定。对于一个成功的反馈成像仔细选择的轨道参数（大小和定时）的需要和这些参数具有基于所述荧光体颗粒，有必要进行跟踪的特性来进行调整。 该技术的物理和数学基础，在过去4,5 2D和3D应用程序进行了描述。在这个协议中，我们简要地描述了安装的主要硬件部件，并且更详细的参数的选择和样品制备所需的典型的实验中，使我们以下溶酶体中的活细胞内的高时间分辨率的位移。

<table border="0" cellpadding="0" cellspacing="0" width="525">
	<tbody>
		<tr height="20">
			<td height="20" style="height:20px;width:197px;">Name</td>
			<td style="width:160px;">Company</td>
			<td style="width:168px;">Model</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Lysotracker DND 26</td>
			<td>Life technologies</td>
			<td>L-7526</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">tubuline tracker Green</td>
			<td>Life technologies</td>
			<td>T34075</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Mitotracker RED</td>
			<td>Life technologies</td>
			<td>M7512</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Coherent Chamelon- ultra II TI</td>
			<td>Coherent</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Calcite polarize</td>
			<td>Melles Griot Glan&#160;</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Galvanometer-motor mirror</td>
			<td>Cambridge technologies</td>
			<td>M 6350</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Dichroic mirror</td>
			<td>Chroma technologies</td>
			<td>700 DCSPXR</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Motorized stage</td>
			<td>ASI</td>
			<td>MS2000</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Piezo&#160;</td>
			<td>PI</td>
			<td>P721-LLQ</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Photomultiplier tube</td>
			<td>Hamamatsu</td>
			<td>H7422P-40</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Data acquisition card</td>
			<td>IO tech</td>
			<td>PCI 1128-4000</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;"></td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Imaging software</td>
			<td>LFD</td>
			<td>Global for images-SimFCS</td>
		</tr>
	</tbody>
</table>

3d orbital tracking in a modified two-photon microscope: an application to the tracking of intracellular vesicles

这个视频协议的目的是讨论如何使用修改后的双光子显微镜1执行和分析三维荧光轨道粒子跟踪实验。相对于传统的方法（光栅扫描或基于一个堆栈帧的宽域），三维轨道跟踪允许定位和跟踪具有高空间（10 nm的精度）和时间分辨率（50赫兹的频率响应）的三维位移移动荧光粒子的长度尺度数百微米2的。该方法是基于一种反馈算法来控制，以围绕该对象执行的圆形轨道上的双光子激光扫描显微镜的硬件要跟踪：反馈机制将保持在中心的荧光物，通过控制的位移扫描光束3-5。为了证明这项技术的优势，我们跟着快速移动的细胞器，溶酶体，内人艾尔文细胞6,7。细胞根据标准方法镀，并用市售溶酶体染料染色。我们简要讨论的硬件结构和详细的控制软件，以执行在活细胞内的3d轨道的跟踪实验。我们详细讨论，以控制所述扫描镜和使该光束的动作在颗粒周围的封闭轨道所需要的参数。我们得出结论：通过展示如何此方法可有效地用于活细胞内跟踪沿在三维微管标记的溶酶体的快速运动。溶酶体可以用移动的速度在0.4-0.5微米/秒的范围内，通常显示沿微管网8定向运动。

根据这一协议，快速的3D单粒子跟踪可以在里面用改进的双光子显微镜来跟踪荧光标记的溶酶体的位移活细胞中进行。进行实验包括跟踪一个孤立的溶酶体内体成熟过程后，9移动单元格中的。溶酶体用荧光绿色染料染色，激发在930 nm的利用双光子激发。我们的数据表明，有可能获得的x，y和z的位移轨迹具有32毫秒（ 图1a）的时间分辨率。地毯分析显示沿各轨道上的时间?...

Watch this Scientific Journal Video about 3D Orbital Tracking in a Modified Two-photon Microscope: An Application to the Tracking of Intracellular Vesicles at JoVE.com

3D Orbital Tracking in a Modified Two-photon Microscope: An Application to the Tracking of Intracellular Vesicles

In this video protocol we track - at high speed and in three dimensions - fluorescently labeled lysosomes within living cells, using the orbital tracking method in a modified two-photon microscope.

3d轨道跟踪的改进双光子显微镜之应用：细胞内的囊泡的跟踪

The objective of this video protocol is to discuss how to perform and analyze a three-dimensional fluorescent orbital particle tracking experiment using a ...

3d-orbital-tracking-modified-two-photon-microscope-an-application-to

Research

JoVE Journal

Bioengineering

10.1K 次观看.  University of California, Irvine. In this video protocol we track - at high speed and in three dimensions - fluorescently labeled lysosomes within living cells, using the orbital tracking method in a modified two-photon microscope. 

视频: 3D Orbital Tracking in a Modified Two-photon Microscope: An Application to the Tracking of Intracellular Vesicles

Tracking Hypoxic Signaling within Encapsulated Cell Aggregates

In Diabetes mellitus type 1, autoimmune destruction of the pancreatic &beta;-cells results in loss of insulin production and potentially lethal hyperglycemia. As an alternative treatment option to exogenous insulin injection, transplantation of functional pancreatic tissue has been explored1,2. This approach offers the promise of a more natural, long-term restoration of normoglycemia. Protection of the donor tissue from the host's immune system is required to prevent rejection and encapsulation is a method used to help achieve this aim.
Biologically-derived materials, such as alginate3 and agarose4, have been the traditional choice for capsule construction but may induce inflammation or fibrotic overgrowth5 which can impede nutrient and oxygen transport. Alternatively, synthetic poly(ethylene glycol) (PEG)-based hydrogels are non-degrading, easily functionalized, available at high purity, have controllable pore size, and are extremely biocompatible,6,7,8. As an additional benefit, PEG hydrogels may be formed rapidly in a simple photo-crosslinking reaction that does not require application of non-physiological temperatures6,7. Such a procedure is described here. In the crosslinking reaction, UV degradation of the photoinitiator, 1-[4-(2-Hydroxyethoxy)-phenyl]-2-hydroxy-2-methyl-1-propane-1-one (Irgacure 2959), produces free radicals which attack the vinyl carbon-carbon double bonds of dimethacrylated PEG (PEGDM) inducing crosslinking at the chain ends. Crosslinking can be achieved within 10 minutes. PEG hydrogels constructed in such a manner have been shown to favorably support cells7,9, and the low photoinitiator concentration and brief exposure to UV irradiation is not detrimental to viability and function of the encapsulated tissue10. While we methacrylate our PEG with the method described below, PEGDM can also be directly purchased from vendors such as Sigma.
An inherent consequence of encapsulation is isolation of the cells from a vascular network. Supply of nutrients, notably oxygen, is therefore reduced and limited by diffusion. This reduced oxygen availability may especially impact &beta;-cells whose insulin secretory function is highly dependent on oxygen11-13. Capsule composition and geometry will also impact diffusion rates and lengths for oxygen. Therefore, we also describe a technique for identifying hypoxic cells within our PEG capsules. Infection of the cells with a recombinant adenovirus allows for a fluorescent signal to be produced when intracellular hypoxia-inducible factor (HIF) pathways are activated14. As HIFs are the primary regulators of the transcriptional response to hypoxia, they represent an ideal target marker for detection of hypoxic signaling15. This approach allows for easy and rapid detection of hypoxic cells. Briefly, the adenovirus has the sequence for a red fluorescent protein (Ds Red DR from Clontech) under the control of a hypoxia-responsive element (HRE) trimer. Stabilization of HIF-1 by low oxygen conditions will drive transcription of the fluorescent protein (Figure 1). Additional details on the construction of this virus have been published previously15. The virus is stored in 10% glycerol at -80&deg; C as many 150 &mu;L aliquots in 1.5 mL centrifuge tubes at a concentration of 3.4 x 1010 pfu/mL. 
Previous studies in our lab have shown that MIN6 cells encapsulated as aggregates maintain their viability throughout 4 weeks of culture in 20% oxygen. MIN6 aggregates cultured at 2 or 1% oxygen showed both signs of necrotic cells (still about 85-90% viable) by staining with ethidium bromide as well as morphological changes relative to cells in 20% oxygen. The smooth spherical shape of the aggregates displayed at 20% was lost and aggregates appeared more like disorganized groups of cells. While the low oxygen stress does not cause a pronounced drop in viability, it is clearly impacting MIN6 aggregation and function as measured by glucose-stimulated insulin secretion15. Western blot analysis of encapsulated cells in 20% and 1% oxygen also showed a significant increase in HIF-1&alpha; for cells cultured in the low oxygen conditions which correlates with the expression of the DsRed DR protein.

A method for photo-encapsulation of cells in a crosslinked PEG hydrogel is described. Hypoxic signaling within encapsulated murine insulinoma (MIN6) aggregates is tracked using a fluorescent marker system. This system allows serial examination of cells within a hydrogel scaffold and correlation of hypoxic signaling with changes in cell phenotype.

在封装的细胞聚集跟踪缺氧信号

In Diabetes mellitus type 1, autoimmune destruction of the pancreatic &beta;-cells results in loss of insulin production and potentially lethal ...

科研

生物工程

Longitudinal Measurement of Extracellular Matrix Rigidity in 3D Tumor Models Using Particle-tracking Microrheology

The mechanical microenvironment has been shown to act as a crucial regulator of tumor growth behavior and signaling, which is itself remodeled and modified as part of a set of complex, two-way mechanosensitive interactions. While the development of biologically-relevant 3D tumor models have facilitated mechanistic studies on the impact of matrix rheology on tumor growth, the inverse problem of mapping changes in the mechanical environment induced by tumors remains challenging. Here, we describe the implementation of particle-tracking microrheology (PTM) in conjunction with 3D models of pancreatic cancer as part of a robust and viable approach for longitudinally monitoring physical changes in the tumor microenvironment, in situ. The methodology described here integrates a system of preparing in vitro 3D models embedded in a model extracellular matrix (ECM) scaffold of Type I collagen with fluorescently labeled probes uniformly distributed for position- and time-dependent microrheology measurements throughout the specimen. In vitro tumors are plated and probed in parallel conditions using multiwell imaging plates. Drawing on established methods, videos of tracer probe movements are transformed via the Generalized Stokes Einstein Relation (GSER) to report the complex frequency-dependent viscoelastic shear modulus, G*(&#969;). Because this approach is imaging-based, mechanical characterization is also mapped onto large transmitted-light spatial fields to simultaneously report qualitative changes in 3D tumor size and phenotype. Representative results showing contrasting mechanical response in sub-regions associated with localized invasion-induced matrix degradation as well as system calibration, validation data are presented. Undesirable outcomes from common experimental errors and troubleshooting of these issues are also presented. The 96-well 3D culture plating format implemented in this protocol is conducive to correlation of microrheology measurements with therapeutic screening assays or molecular imaging to gain new insights into impact of treatments or biochemical stimuli on the mechanical microenvironment.

Particle-tracking microrheology can be used to non-destructively quantify and spatially map changes in extracellular matrix mechanical properties in 3D tumor models.

细胞外基质刚性三维肿瘤模型的纵向测量用粒子跟踪Microrheology

The mechanical microenvironment has been shown to act as a crucial regulator of tumor growth behavior and signaling, which is itself remodeled and ...

Long-term Intravital Immunofluorescence Imaging of Tissue Matrix Components with Epifluorescence and Two-photon Microscopy

Besides being a physical scaffold to maintain tissue morphology, the extracellular matrix (ECM) is actively involved in regulating cell and tissue function during development and organ homeostasis. It does so by acting via biochemical, biomechanical, and biophysical signaling pathways, such as through the release of bioactive ECM protein fragments, regulating tissue tension, and providing pathways for cell migration. The extracellular matrix of the tumor microenvironment undergoes substantial remodeling, characterized by the degradation, deposition and organization of fibrillar and non-fibrillar matrix proteins. Stromal stiffening of the tumor microenvironment can promote tumor growth and invasion, and cause remodeling of blood and lymphatic vessels. Live imaging of matrix proteins, however, to this point is limited to fibrillar collagens that can be detected by second harmonic generation using multi-photon microscopy, leaving the majority of matrix components largely invisible. Here we describe procedures for tumor inoculation in the thin dorsal ear skin, immunolabeling of extracellular matrix proteins and intravital imaging of the exposed tissue in live mice using epifluorescence and two-photon microscopy. Our intravital imaging method allows for the direct detection of both fibrillar and non-fibrillar matrix proteins in the context of a growing dermal tumor. We show examples of vessel remodeling caused by local matrix contraction. We also found that fibrillar matrix of the tumor detected with the second harmonic generation is spatially distinct from newly deposited matrix components such as tenascin C. We also showed long-term (12 hours) imaging of T-cell interaction with tumor cells and tumor cells migration along the collagen IV of basement membrane. Taken together, this method uniquely allows for the simultaneous detection of tumor cells, their physical microenvironment and the endogenous tissue immune response over time, which may provide important insights into the mechanisms underlying tumor progression and ultimate success or resistance to therapy.

The extracellular matrix undergoes substantial remodeling during wound healing, inflammation and tumorigenesis. We present a novel intravital immunofluorescence microscopy approach to visualize the dynamics of fibrillar as well as mesh-like matrix components with high spatial and temporal resolution using epifluorescence or two-photon microscopy.

与落射荧光组织基质成分和双光子显微镜的长期活体免疫荧光成像

Besides being a physical scaffold to maintain tissue morphology, the extracellular matrix (ECM) is actively involved in regulating cell and tissue ...

In Situ Mapping of the Mechanical Properties of Biofilms by Particle-tracking Microrheology

Bacterial cells are able to form surface-attached biofilm communities known as biofilms by encasing themselves in extracellular polymeric substances (EPS). The EPS serves as a physical and protective scaffold that houses the bacterial cells and consists of a variety of materials that includes proteins, exopolysaccharides and DNA. The composition of the EPS may change, which remodels the mechanic properties of the biofilm to further develop or support alternative biofilm structures, such as streamers, as a response to environmental cues. Despite this, there are little quantitative descriptions on how EPS components contribute to the mechanical properties and function of biofilms. Rheology, the study of the flow of matter, is of particular relevance to biofilms as many biofilms grow in flow conditions and are constantly exposed to shear stress. It also provides measurement and insight on the spreading of the biofilm on a surface. Here, particle-tracking microrheology is used to examine the viscoelasticity and effective crosslinking roles of different matrix components in various parts of the biofilm during development. This approach allows researchers to measure mechanic properties of biofilms at the micro-scale, which might provide useful information for controlling and engineering biofilms.

In Situ Mapping of the Mechanical Properties of Biofilms by Particle-tracking Microrheology

Particle-tracking microrheology investigates the viscoelasticity of materials. Here, the technique is used to determine the viscoelasticity, creep compliance and effective crosslinking roles of different matrix components of a bacterial biofilm. The matrix consists of polymeric substances secreted by the bacteria and its components determine biofilm structure and mechanical properties.

在生物膜的力学性能原位制图粒子追踪Microrheology

Bacterial cells are able to form surface-attached biofilm communities known as biofilms by encasing themselves in extracellular polymeric substances ...

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to spatially fractionate the sample based on a biological property of interest. For the resultant spatial distribution to be used as the assay readout, microfluidic devices are often subjected to microscopic analysis requiring complex instrumentation with higher cost and reduced portability. To address this limitation, we have developed an integrated electronic sensing technology for multiplexed detection of particles at different locations on a microfluidic chip. Our technology, called Microfluidic CODES, combines Resistive Pulse Sensing with Code Division Multiple Access to compress 2D spatial information into a 1D electrical signal. In this paper, we present a practical demonstration of the Microfluidic CODES technology to detect and size cultured cancer cells distributed over multiple microfluidic channels. As validated by the high-speed microscopy, our technology can accurately analyze dense cell populations all electronically without the need for an external instrument. As such, the Microfluidic CODES can potentially enable low-cost integrated lab-on-a-chip devices that are well suited for the point-of-care testing of biological samples.

We demonstrate a microfluidic platform with an integrated surface electrode network that combines resistive pulse sensing (RPS) with code division multiple access (CDMA), to multiplex detection and sizing of particles in multiple microfluidic channels.

与复用电子检测的粒子的空间跟踪微流体平台

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to ...

Assembly and Tracking of Microbial Community Development within a Microwell Array Platform

The development of microbial communities depends on a combination of complex deterministic and stochastic factors that can dramatically alter the spatial distribution and activities of community members. We have developed a microwell array platform that can be used to rapidly assemble and track thousands of bacterial communities in parallel. This protocol highlights the utility of the platform and describes its use for optically monitoring the development of simple, two-member communities within an ensemble of arrays within the platform. This demonstration uses two mutants of Pseudomonas aeruginosa, part of a series of mutants developed to study Type VI secretion pathogenicity. Chromosomal inserts of either mCherry or GFP genes facilitate the constitutive expression of fluorescent proteins with distinct emission wavelengths that can be used to monitor community member abundance and location within each microwell. This protocol describes a detailed method for assembling mixtures of bacteria into the wells of the array and using time-lapse fluorescence imaging and quantitative image analysis to measure the relative growth of each member population over time. The seeding and assembly of the microwell platform, the imaging procedures necessary for the quantitative analysis of microbial communities within the array, and the methods that can be used to reveal interactions between microbial species area all discussed.

The development of microbial communities depends on a combination of factors, including environmental architecture, member abundance, traits, and interactions. This protocol describes a synthetic, microfabricated environment for the simultaneous tracking of thousands of communities contained in femtoliter wells, where key factors such as niche size and confinement can be approximated.

微孔阵列平台中微生物群落发展的组装与跟踪

The development of microbial communities depends on a combination of complex deterministic and stochastic factors that can dramatically alter the spatial ...

A Protocol for Real-time 3D Single Particle Tracking

Real-time three-dimensional single particle tracking (RT-3D-SPT) has the potential to shed light on fast, 3D processes in cellular systems. Although various RT-3D-SPT methods have been put forward in recent years, tracking high speed 3D diffusing particles at low photon count rates remains a challenge. Moreover, RT-3D-SPT setups are generally complex and difficult to implement, limiting their widespread application to biological problems. This protocol presents a RT-3D-SPT system named 3D Dynamic Photon Localization Tracking (3D-DyPLoT), which can track particles with high diffusive speed (up to 20 &#181;m2/s) at low photon count rates (down to 10 kHz). 3D-DyPLoT employs a 2D electro-optic deflector (2D-EOD) and a tunable acoustic gradient (TAG) lens to drive a single focused laser spot dynamically in 3D. Combined with an optimized position estimation algorithm, 3D-DyPLoT can lock onto single particles with high tracking speed and high localization precision. Owing to the single excitation and single detection path layout, 3D-DyPLoT is robust and easy to set up. This protocol discusses how to build 3D-DyPLoT step by step. First, the optical layout is described. Next, the system is calibrated and optimized by raster scanning a 190 nm fluorescent bead with the piezoelectric nanopositioner. Finally, to demonstrate real-time 3D tracking ability, 110 nm fluorescent beads are tracked in water.

This protocol details the construction and operation of a real-time 3D single particle tracking microscope capable of tracking nanoscale fluorescent probes at high diffusive speeds and low photon count rates.

一种实时3D 单粒子跟踪协议

Real-time three-dimensional single particle tracking (RT-3D-SPT) has the potential to shed light on fast, 3D processes in cellular systems. Although ...

An Orbital Shaking Culture of Mammalian Cells in O-shaped Vessels to Produce Uniform Aggregates

Suspension cultures of mammalian cell aggregates are required for various applications in medical and biotechnological fields. The disposable bag-based method is one of the simplest techniques for the mass production of cellular aggregates, but it does not protect the cultures against over-aggregation, which occurs when they gather at the bottom center of the culture vessel. To solve this problem, we developed an O-shaped dish and an O-shaped bag, neither of which contains a central region. Aggregates grown in either O-shaped culture vessel were noticeably more uniform in size than aggregates grown in conventional vessels. Histological analyses showed that aggregates in conventional culture dishes contained necrotic cores most likely caused by a poor oxygen supply. In contrast, aggregates that were grown in the O-shaped bag, even those with similar diameters to aggregates in conventional culture dishes, did not show necrotic cores. These results suggest that the O-shaped bag provides sufficient oxygen to the aggregates due to the oxygen permeability of the bag material. We, therefore, propose that this novel gas-permeable O-shaped culture bag is suitable for the mass production of uniform aggregates that are necessary in various biotechnological fields.

Here we present a protocol for using O-shaped vessels, specialized for suspension cultures of cellular aggregates, with orbital shaking. The HEK293 cells grown in this bag form more homogeneous aggregates than those grown in conventional culture vessels.

o 型血管哺乳动物细胞产生均匀集料的轨道晃动培养

Suspension cultures of mammalian cell aggregates are required for various applications in medical and biotechnological fields. The disposable bag-based ...

Segmenting Growth of Endothelial Cells in 6-Well Plates on an Orbital Shaker for Mechanobiological Studies

Shear stress imposed on the arterial wall by the flow of blood affects endothelial cell morphology and function. Low magnitude, oscillatory and multidirectional shear stresses have all been postulated to stimulate a pro-atherosclerotic phenotype in endothelial cells, whereas high magnitude and unidirectional or uniaxial shear are thought to promote endothelial homeostasis. These hypotheses require further investigation, but traditional in vitro techniques have limitations, and are particularly poor at imposing multidirectional shear stresses on cells. 
One method that is gaining increasing use is to culture endothelial cells in standard multi-well plates on the platform of an orbital shaker; in this simple, low-cost, high-throughput and chronic method, the swirling medium produces different patterns and magnitudes of shear, including multidirectional shear, in different parts of the well. However, it has a significant limitation: cells in one region, exposed to one type of flow, may release mediators into the medium that affect cells in other parts of the well, exposed to different flows, hence distorting the apparent relation between flow and phenotype. 
Here we present an easy and affordable modification of the method that allows cells to be exposed only to specific shear stress characteristics. Cell seeding is restricted to a defined region of the well by coating the region of interest with fibronectin, followed by passivation using passivating solution. Subsequently, the plates can be swirled on the shaker, resulting in exposure of cells to well-defined shear profiles such as low magnitude multidirectional shear or high magnitude uniaxial shear, depending on their location. As before, the use of standard cell-culture plasticware allows straightforward further analysis of the cells. The modification has already allowed the demonstration of soluble mediators, released from endothelium under defined shear stress characteristics, that affect cells located elsewhere in the well.

This protocol describes a coating method to restrict endothelial cell growth to a specific region of a 6-well plate for shear stress application using the orbital shaker model.

在机械生物学研究的轨道摇床上的 6 井板中分段内皮细胞的生长

Shear stress imposed on the arterial wall by the flow of blood affects endothelial cell morphology and function. Low magnitude, oscillatory and ...

An In vitro System to Gauge the Thrombolytic Efficacy of Histotripsy and a Lytic Drug

Deep vein thrombosis (DVT) is a global health concern. The primary approach to achieve vessel recanalization for critical obstructions is catheter-directed thrombolytics (CDT). To mitigate caustic side effects and the long treatment time associated with CDT, adjuvant and alternative approaches are under development. One such approach is histotripsy, a focused ultrasound therapy to ablate tissue via bubble cloud nucleation. Pre-clinical studies have demonstrated strong synergy between histotripsy and thrombolytics for clot degradation. This report outlines a benchtop method to assess the efficacy of histotripsy-aided thrombolytic therapy, or lysotripsy.
Clots manufactured from fresh human venous blood were introduced into a flow channel whose dimensions and acousto-mechanical properties mimic an iliofemoral vein. The channel was perfused with plasma and the lytic&#160;recombinant tissue-type plasminogen activator. Bubble clouds were generated in the clot with a focused ultrasound source designed for the treatment of femoral venous clots. Motorized positioners were used to translate the source focus along the clot length. At each insonation location, acoustic emissions from the bubble cloud were passively recorded, and beamformed to generate passive cavitation images. Metrics to gauge treatment efficacy included clot mass loss (overall treatment efficacy), and the concentrations of D-dimer (fibrinolysis) and hemoglobin (hemolysis) in the perfusate. There are limitations to this in vitro design, including lack of means to assess in vivo side effects or dynamic changes in flow rate as the clot lyses. Overall, the setup provides an effective method to assess the efficacy of histotripsy-based strategies to treat DVT.

Histotripsy-aided lytic delivery or lysotripsy is under development for the treatment of deep vein thrombosis. An in vitro procedure is presented here to assess the efficacy of this combination therapy. Key protocols for the clot model, image guidance, and assessment of treatment efficacy are discussed.