Questo lavoro è stato sostenuto in parte dai fondi di avvio della University of Nebraska Medical Center e National Institute of Health (codice di autorizzazione 1R15 AR063901-01).

1. Preparazione della soluzione <ol><li> Preparare una soluzione di poli (ε-caprolattone) (PCL) (M w = 80,000 g / mol) ad una concentrazione approssimativa di 100 mg / ml. Sciogliere PCL in una miscela di diclorometano (DCM) e N, N-dimethlyformamide (DMF) con un rapporto di 4: 1 (v / v) con una concentrazione del 10% (w / v). </li><li> Porre la soluzione in un tubo di vetro da 20 ml per la miscelazione. Mettere tubo di vetro in ultrasuoni per 30 minuti, o fino a quando la soluzione è trasparente. </li></ol> 2. Apparecchiatura Preparazione <ol><li> Aggiungere la soluzione PCL preparata in una siringa da 5 ml con un ago senza punta 21 gauge collegato. </li><li> Inserire pompa a siringa in posizione electrospinning verticale di figura 1. </li><li> Utilizzare un collettore in acciaio inox-gap con uno spazio aperto di 2 cm x 5 cm per il substrato di fibre allineate. Posizionare il collettore 12 centimetri dalla punta dell&#39;ago. </li><li> Collegare la corrente continua (DC) ad alta tensione di alimentazione alago e terra il collettore. Assicurarsi che il collettore è individualmente a terra senza contatto per le altre apparecchiature di laboratorio. </li></ol> 3. Electrospinning <ol><li> Set pompa a siringa a 1.50 ml / h, fino a quando le goccioline che formano sulla punta dell&#39;ago vengono immediatamente sostituiti quando viene rimosso. Quindi, impostare la portata di 0,50 ml / h. </li><li> Girare l&#39;operatore tensione di 12 kV. </li><li> Electrospin fino a quando le fibre uniaxially allineate coprire completamente il gap sul collettore. </li><li> Applicare la colla ai bordi di una piccola lastra di vetro e trasferire le fibre dal collettore gap alla lastra di vetro. Posizionare la lastra di vetro nella parte superiore di un pezzo di foglio di alluminio che ha la stessa dimensione della lastra di vetro ed è messo a terra. </li><li> Posizionare il secondo collettore siringa secondo la figura 3. </li><li> Fissare la maschera di plastica per la seconda pompa siringa e posizione it 2 mm sopra il collettore. </li><li> Aggiungi cumarina 6 a 1% (w / w) per il PCL soluzione se nanoencapsulation è desired- e mescolare fino a quando la soluzione è trasparente. </li><li> Caricare il PCL o PCL / cumarina 6 soluzione in un ago 5 ml con un ottuso ago 21 gauge. Impostare pompa verticale a 0,50 ml / hr e orizzontale per tirare 9 ml / hr o ad una velocità di circa 1 mm / min. </li><li> Electrospin finché la maschera è spostato quasi completamente fuori dal collettore, ma con la zona di bordo ancora sotto la maschera. </li></ol> 4. Fiber Caratterizzazione <ol><li> I campioni con nastro adesivo conduttivo biadesivo al perno metallico e il cappotto con platino per 40 sec con una verniciatura polverizzazione a 40 mA. <ol><li> Esaminare fibre attraverso microscopio elettronico a scansione (SEM) secondo i nostri studi precedenti 17,18. </li><li> Raccogliere immagini ad una tensione di accelerazione di 15 kV. </li></ol></li><li> Eseguire l&#39;analisi rapida di Fourier (FFT) su un campione di fibra separato per misurare l&#39;allineamento fibra. Le informazioni dettagliate su allineamento delle fibre di misura da FFT può riferirsi to studi precedenti 19,20. </li></ol> 5. Cellule staminali Seeding. <ol><li> Sterilizzare i campioni di fibre immergendola in una soluzione di etanolo al 70% per 2 ore. Quindi lavare le fibre con acqua distillata per rimuovere eventuali contaminanti. </li><li> Ottenere ADSCs umane e cellule di coltura in una beuta da 25 cm 2 a 37 ° C in atmosfera di 95% aria / 5% CO 2. Modificare il terreno di coltura cellulare a giorni 10. </li><li> Trypsinize cellule e contare il numero di cellule. Specificamente, rimuovere tutto terreno di coltura dal pallone di coltura cellulare e lavare le cellule con tampone fosfato salino (PBS) due volte. Poi aggiungere 1 m l di una soluzione 0,25% tripsina-EDTA (pre-caldo in bagno d&#39;acqua a 37 ° C) per coprire il monostrato cellulare e incubare la beuta nell&#39;incubatrice coltura cellulare per 2-3 minuti. Aggiungere 4 ml terreno di coltura e lavare tutte le cellule dalla superficie pipettando il mezzo su tutta la superficie. Centrifugare la sospensione cellulare e ri-disperse esimoe pellet di cellule nel mezzo di coltura. Contare le celle tramite emocitometro. Seed circa 1 × 10 4 celle al patibolo nanofibre collocato in un piatto -Cultura 35 millimetri e incubare per 3 e 7 giorni. </li><li> Cellule macchia con fluoresceina diacetato (5 mg / ml in acetone) (FDA) allora l&#39;immagine dei campioni utilizzando un microscopio a fluorescenza. In particolare, aggiungere 100 ml di soluzione FDA al piatto cultura e incubare per 30 min. Lavare le cellule con PBS per tre volte prima di imaging fluorescente. Analizzare l&#39;orientamento delle cellule da un programma personalizzato mat-lab in base alle nostre precedenti studi 10. </li></ol>

<ol>
	<li>Xie, J., Li, X., Xia, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Putting+electrospun+nanofibers+to+work+for+biomedical+research.">Putting electrospun nanofibers to work for biomedical research.</a> Macromol. Rapid Commun. 29 (22), 1775-1792 (2008).</li><li>Genin, G. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Functional+grading+of+mineral+and+collagen+in+the+attachment+of+tendon+to+bone.">Functional grading of mineral and collagen in the attachment of tendon to bone.</a> Biophys. J. 97 (4), 976-985 (2009).</li><li>Thomopoulos, S., Marquez, J. P., Weinberger, B., Birman, V., Genin, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Collagen+fiber+orientation+at+the+tendon+to+bone+insertion+and+its+influence+on+stress+concentrations.">Collagen fiber orientation at the tendon to bone insertion and its influence on stress concentrations.</a> J. Biomech. 39 (10), 1842-1851 (2006).</li><li>Thomopoulos, S., Williams, G. R., Gimbel, J. A., Favata, M., Soslowsky, L. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Variation+of+biomechanical,+structural,+and+compositional+properties+along+the+tendon+to+bone+insertion+site.">Variation of biomechanical, structural, and compositional properties along the tendon to bone insertion site.</a> J. Orthop. Res. 21 (3), 413-419 (2003).</li><li>Thomopoulos, S., Genin, G. M., Galatz, L. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+development+and+morphogenesis+of+the+tendon-to-bone+insertion+-+What+development+can+teach+us+about+healing.">The development and morphogenesis of the tendon-to-bone insertion - What development can teach us about healing.</a> Musculoskelet Neuronal Interact. 10 (1), 35-45 (2010).</li><li>Li, X., Xie, J., Lipner, J., Yuan, X., Thomopoulos, S., Xia, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nanofiber+scaffolds+with+gradations+in+mineral+content+for+mimicking+the+tendon-to-bone+insertion+site.">Nanofiber scaffolds with gradations in mineral content for mimicking the tendon-to-bone insertion site.</a> Nano Lett. 9 (7), 2763-2768 (2009).</li><li>Kunzler, T. P., Huwiler, C., Drobek, T., V&#246;r&#246;s, J., Spencer, N. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Systematic+study+of+osteoblast+response+to+nanotopography+by+means+of+nanoparticle-density+gradients.">Systematic study of osteoblast response to nanotopography by means of nanoparticle-density gradients.</a> Biomaterials. 28 (33), 5000-5006 (2007).</li><li>Huwiler, C., Kunzler, T. P., Textor, M., V&#246;r&#246;s, J., Spencer, N. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Functionalizable+nanomorphology+gradients+via+colloidal+self-assembly.">Functionalizable nanomorphology gradients via colloidal self-assembly.</a> Langmuir. 23 (11), 5929-5935 (2007).</li><li>Xie, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term='Aligned-to-random'+nanofiber+scaffolds+for+mimicking+the+structure+of+the+tendon-to-bone+insertion+site.">'Aligned-to-random' nanofiber scaffolds for mimicking the structure of the tendon-to-bone insertion site.</a> Nanoscale. 2 (6), 923-926 (2010).</li><li>Xie, J., Ma, B., Michael, P. L., Shuler, F. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fabrication+of+nanofiber+scaffolds+with+gradations+in+fiber+organization+and+their+potential+applications.">Fabrication of nanofiber scaffolds with gradations in fiber organization and their potential applications.</a> Macromol. Biosci. 12 (10), 1336-1341 (2012).</li><li>James, R., Kumbar, S. G., Laurencin, C. T., Balian, G., Chhabra, A. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tendon+tissue+engineering:+adipose-derived+stem+cell+and+GDF-5+mediated+regeneration+using+electrospun+matrix+systems.">Tendon tissue engineering: adipose-derived stem cell and GDF-5 mediated regeneration using electrospun matrix systems.</a> Biomed. Mater. 6 (2), 025011 (2011).</li><li>Bodle, J. C., Hanson, A. D., Loboa, E. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adipose-derived+stem+cells+in+functional+bone+tissue+engineering:+lessons+from+bone+mechanobiology.">Adipose-derived stem cells in functional bone tissue engineering: lessons from bone mechanobiology.</a> Tissue Eng. Part B Rev. 17 (3), 195-211 (2011).</li><li>Lee, J. H., Rhie, J. W., Oh, D. Y., Ahn, S. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Osteogenic+differentiation+of+human+adipose+tissue-derived+stromal+cells+(hASCs)+in+a+porous+three-dimensional+scaffold.">Osteogenic differentiation of human adipose tissue-derived stromal cells (hASCs) in a porous three-dimensional scaffold.</a> Biochem. Biophys. Res. Commun. 370 (3), 456-460 (2008).</li><li>Tapp, H., Hanley, E. N., Patt, J. C., Gruber, H. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adipose-derived+stem+cells:+characterization+and+current+application+in+orthopaedic+tissue+repair.">Adipose-derived stem cells: characterization and current application in orthopaedic tissue repair.</a> Exp. Biol. Med. 234 (1), 1-9 (2009).</li><li>Gimble, J. M., Guilak, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adipose-derived+adult+stem+cells:+isolation,+characterization,+and+differentiation+potential.">Adipose-derived adult stem cells: isolation, characterization, and differentiation potential.</a> Cytotherapy. 5 (5), 362-369 (2003).</li><li>Zuk, P. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multilineage+cells+from+human+adipose+tissue:+implications+for+cell-based+therapies.">Multilineage cells from human adipose tissue: implications for cell-based therapies.</a> Tissue Eng. 7 (2), 211-228 (2001).</li><li>Xie, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+differentiation+of+embryonic+stem+cells+seeded+on+electrospun+nanofibers+into+neural+lineages.">The differentiation of embryonic stem cells seeded on electrospun nanofibers into neural lineages.</a> Biomaterials. 30 (3), 354-362 (2009).</li><li>Xie, J., MacEwan, M. R., Li, X., Sakiyama-Elbert, S. E., Xia, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Neurite+outgrowth+on+nanofiber+scaffolds+with+different+orders,+structures,+and+surface+properties.">Neurite outgrowth on nanofiber scaffolds with different orders, structures, and surface properties.</a> ACS Nano. 3 (5), 1151-1159 (2009).</li><li>Ayres, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modulation+of+anisotropy+in+electrospun+tissue+engineering+scaffolds:+analysis+of+fiber+alignment+by+the+fast+Fourier+transform.">Modulation of anisotropy in electrospun tissue engineering scaffolds: analysis of fiber alignment by the fast Fourier transform.</a> Biomaterials. 27 (32), 5524-5534 (2006).</li><li>Ayres, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measuring+fiber+alignment+in+electrospun+scaffolds:+a+user&#8217;s+guide+to+the+2D+fast+Fourier+transform+approach.">Measuring fiber alignment in electrospun scaffolds: a user&#8217;s guide to the 2D fast Fourier transform approach.</a> J. Biomater. Sci. Poly. Ed. 19 (5), 603-621 (2008).</li></ol>

The authors have nothing to disclose.

The most critical part of the protocol is generation of the gradient scaffold. It is imperative that the mask covering the collector moves at a constant velocity so there is a gradual change within the fiber scaffold. The correct preparation of PCL solution is also important to ensure electrospinning success. Checking the fiber morphology prior to electrospinning is recommendable, especially after the encapsulation of Coumarin-6, which may require a higher voltage to electrospin correctly. 
Fu...

Nanofibre sono un&#39;utilità popolare per ingegneria tissutale a causa della loro capacità di mimare la matrice extracellulare nella sua struttura e dimensione relativa 1. Tuttavia, alcune interfacce tessuto nativo, come il sito tendine-osso, contengono fibre collagene, che presentano una struttura organizzativa variabile che aumenta in allineamento verso il tendine e diminuisce al sito osseo 2-5. Così, per la rigenerazione tissutale efficace è necessario per fabbricare un ponteggio che potrebbe efficacemente imitare questo gradiente strutturale. In precedenza, vi è stata una ricerca condotta sui cambiamenti graduali nella composizione delle fibre, in particolare, il contenuto di minerali 6. Tuttavia, ricreando la componente strutturale dei tessuti connettivi rimane in gran parte inesplorato. Uno studio precedente esaminato gradienti morfologiche studiando l&#39;effetto della silice superficie densità di particelle sulla proliferazione degli osteoblasti ratto cranica e trovato un inverrapporto tra la densità se particella di silice e la proliferazione cellulare 7. Ma i cambiamenti morfologici che mediate proliferazione cellulare in lavori precedenti erano per lo più relativi alla rugosità superficiale manca la capacità di mimare fibra cambiamenti organizzativi 7,8. Uno studio recente ha tentato di realizzare un ponteggio che imitava gli orientamenti fibre collagene unici utilizzando un nuovo collettore per electrospinning 9. Anche se questo studio è riuscito a produrre un ponteggio con fibre sia allineate e casuale, non è riuscito a imitare i graduali cambiamenti esposti nei tessuti nativi. Inoltre, nella produzione di componenti separati, con un cambiamento immediato dal allineato all&#39;orientamento casuale, le proprietà biomeccaniche di questa impalcatura è diminuito in modo significativo. Nessun lavoro precedente è stato in grado di produrre applicabili ponteggi nanofibre con continui gradazioni orientamenti fibra di allineato e casuali. Il nostro recente studio ha dimostrato con successo la ricreazione di ponteggi nanofibrecon gradazioni nell&#39;organizzazione fibra che può potenzialmente mimare l&#39;organizzazione collagene nativo all&#39;inserimento di 10 tendine-osso. Questo lavoro si propone di presentare i protocolli utilizzati per la produzione di scaffold nanofibre con una struttura molto simile a quella di organizzazione fibre nell&#39;interfaccia nativa tendine-osso tessuti. Strutture nanofibre gradiente sono potenzialmente di vasta portata applicazioni attraverso una varietà di campi. Ci siamo concentrati sulle applicazioni per l&#39;ingegneria tissutale del sito di tendine-osso combinando le nostre impalcature con le cellule staminali derivate da tessuto adiposo (ADSCs) che sono già utilizzate per la rigenerazione dei tessuti su vari substrati 11-14. Inoltre, ADSCs sono molto simili in natura per le cellule staminali del midollo osseo in termini di multipotenza e la loro risorsa è abbondante che può essere raccolto mediante una semplice procedura di liposuzione 15,16. Semina queste cellule per ponteggi nanofibre sfumati aumenta ulteriormente la loro tiscitare applicazioni ingegneristiche consentendo la distribuzione controllata delle cellule che possono potenzialmente differenziarsi in vari tessuti. Oltre a seminare le cellule staminali, nanofibre possono essere incapsulati con molecole di segnalazione per la regolazione della risposta cellulare. Accoppiamento nanoencapsulation con il gradiente organizzativa di tali ponteggi consente lo studio del comportamento cellulare o possibili disegni implantari e rivestimenti. Incapsulamento di molecole funzionali come proteina morfogenetica 2 (BMP2), che ha dimostrato di indurre la differenziazione degli osteoblasti 15,16, potrebbe migliorare ulteriormente le applicazioni di ingegneria tissutale di questi ponteggi 10.

<table border="0" cellpadding="0" cellspacing="0">
	<tbody>
		<tr>
			<td>Polycaprolactone</td>
			<td>Sigma-Aldrich</td>
			<td>440744</td>
			<td></td>
		</tr>
		<tr>
			<td>N,N-Dimethlyformamide</td>
			<td>Fisher Chemical</td>
			<td>D-119-1</td>
			<td></td>
		</tr>
		<tr>
			<td>Dichloromethane</td>
			<td>Fisher Chemical</td>
			<td>AC61093-1000</td>
			<td></td>
		</tr>
		<tr>
			<td>Coumarin 6</td>
			<td>Sigma-Aldrich</td>
			<td>546283</td>
			<td></td>
		</tr>
		<tr>
			<td>Adipose Derived Stem Cells</td>
			<td>Cellular engineering Technologies</td>
			<td>HMSC.AD-100</td>
			<td></td>
		</tr>
		<tr>
			<td>Fetal Bovine Serum</td>
			<td>Life Technologies</td>
			<td>26140-111</td>
			<td></td>
		</tr>
		<tr>
			<td>Fluorescein Diacetate</td>
			<td>Sigma-Aldrich</td>
			<td>F7378</td>
			<td></td>
		</tr>
		<tr>
			<td>Ethanol</td>
			<td>Sigma-Aldrich</td>
			<td>E7023</td>
			<td></td>
		</tr>
		<tr>
			<td>Trypsin-EDTA</td>
			<td>Invitrogen</td>
			<td>25300-054</td>
			<td></td>
		</tr>
		<tr>
			<td>&#945;-Modified Eagle&#39;s Medium</td>
			<td>Invitrogen</td>
			<td>a10490-01</td>
			<td></td>
		</tr>
		<tr>
			<td>Acetone</td>
			<td>Fisher Scientific</td>
			<td>s25120a</td>
			<td></td>
		</tr>
		<tr>
			<td>Phosphate Buffered Saline</td>
			<td>Invitrogen</td>
			<td>10010023</td>
			<td></td>
		</tr>
		<tr>
			<td>Glass Slides</td>
			<td>VWR international, LLC</td>
			<td>101412-842</td>
			<td></td>
		</tr>
		<tr>
			<td>Syringe Pump</td>
			<td>Fisher Scientific</td>
			<td>14-831-200</td>
			<td>Single syringe</td>
		</tr>
		<tr>
			<td>Ultrasonic Cleaner</td>
			<td>Branson</td>
			<td>1510</td>
			<td></td>
		</tr>
		<tr>
			<td>High Voltage DC Power Supply</td>
			<td>Gamma High Voltage Research</td>
			<td>ES30</td>
			<td></td>
		</tr>
		<tr>
			<td>Scanning Electron Microscope</td>
			<td>FEI</td>
			<td>Nova 2300</td>
			<td></td>
		</tr>
		<tr>
			<td>Fluorescence Microscope</td>
			<td>Zeiss</td>
			<td>Axio Imager 2</td>
			<td></td>
		</tr>
	</tbody>
</table>

electrospun nanofiber scaffolds with gradations in fiber organization

The goal of this protocol is to report a simple method for generating nanofiber scaffolds with gradations in fiber organization and test their possible applications in controlling cell morphology/orientation. Nanofiber organization is controlled with a new fabrication apparatus that enables the gradual decrease of fiber organization in a scaffold. Changing the alignment of fibers is achieved through decreasing deposition time of random electrospun fibers on a uniaxially aligned fiber mat. By covering the collector with a moving barrier/mask, along the same axis as fiber deposition, the organizational structure is easily controlled. For tissue engineering purposes, adipose-derived stem cells can be seeded to these scaffolds. Stem cells undergo morphological changes as a result of their position on the varied organizational structure, and can potentially differentiate into different cell types depending on their locations. Additionally, the graded organization of fibers enhances the biomimicry of nanofiber scaffolds so they more closely resemble the natural orientations of collagen nanofibers at tendon-to-bone insertion site compared to traditional scaffolds. Through nanoencapsulation, the gradated fibers also afford the possibility to construct chemical gradients in fiber scaffolds, and thereby further strengthen their potential applications in fast screening of cell-materials interaction and interfacial tissue regeneration. This technique enables the production of continuous gradient scaffolds, but it also can potentially produce fibers in discrete steps by controlling the movement of the moving barrier/mask in a discrete fashion.

Usando questo protocollo, si è formata una stuoia in fibra con pendenza organizzativa. La figura 3 mostra le immagini SEM scattate in varie posizioni sul patibolo nanofibre. Qualitativamente, si può determinare che esiste una progressione da fibre uniaxially allineate a 0 mm (Figura 3A) ad una fibra assortimento casuale a 6 mm (Figura 3D). La FFT dà un valore quantitativo per l&#39;allineamento delle fibre, specifiche sui processi quantitativi sono dettagliate qui <s...

Watch this Scientific Journal Video about Electrospun Nanofiber Scaffolds with Gradations in Fiber Organization at JoVE.com

Electrospun Nanofiber Scaffolds with Gradations in Fiber Organization

Qui, vi presentiamo un protocollo per fabbricare scaffold elettrofilate nanofibre con organizzazione sfumati di fibre e di esplorare le loro applicazioni nella regolazione della morfologia delle cellule / orientamento. Gradienti per quanto riguarda le proprietà fisiche e chimiche dei ponteggi nanofibre offrono un&#39;ampia varietà di applicazioni in campo biomedico.

Elettrofilate nanofibre Ponteggi con gradazioni Organizzazione Fiber

The goal of this protocol is to report a simple method for generating nanofiber scaffolds with gradations in fiber organization and test their possible ...

electrospun-nanofiber-scaffolds-with-gradations-in-fiber-organization

Research

JoVE Journal

Bioengineering

9.7K Views.  University of Nebraska Medical Center.  Qui, vi presentiamo un protocollo per fabbricare scaffold elettrofilate nanofibre con organizzazione sfumati di fibre e di esplorare le loro applicazioni nella regolazione della morfologia delle cellule / orientamento. Gradienti per quanto riguarda le proprietà fisiche e chimiche dei ponteggi nanofibre offrono un'ampia varietà di applicazioni in campo biomedico. 

Video: Electrospun Nanofiber Scaffolds with Gradations in Fiber Organization

Elastomeric PGS Scaffolds in Arterial Tissue Engineering

Cardiovascular disease is one of the leading cause of mortality in the US and especially, coronary artery disease increases with an aging population and increasing obesity1. Currently, bypass surgery using autologous vessels, allografts, and synthetic grafts are known as a commonly used for arterial substitutes2. However, these grafts have limited applications when an inner diameter of arteries is less than 6 mm due to low availability, thrombotic complications, compliance mismatch, and late intimal hyperplasia3,4. To overcome these limitations, tissue engineering has been successfully applied as a promising alternative to develop small-diameter arterial constructs that are nonthrombogenic, robust, and compliant. Several previous studies have developed small-diameter arterial constructs with tri-lamellar structure, excellent mechanical properties and burst pressure comparable to native arteries5,6. While high tensile strength and burst pressure by increasing collagen production from a rigid material or cell sheet scaffold, these constructs still had low elastin production and compliance, which is a major problem to cause graft failure after implantation. Considering these issues, we hypothesized that an elastometric biomaterial combined with mechanical conditioning would provide elasticity and conduct mechanical signals more efficiently to vascular cells, which increase extracellular matrix production and support cellular orientation.
The objective of this report is to introduce a fabrication technique of porous tubular scaffolds and a dynamic mechanical conditioning for applying them to arterial tissue engineering. We used a biodegradable elastomer, poly (glycerol sebacate) (PGS)7 for fabricating porous tubular scaffolds from the salt fusion method. Adult primary baboon smooth muscle cells (SMCs) were seeded on the lumen of scaffolds, which cultured in our designed pulsatile flow bioreactor for 3 weeks. PGS scaffolds had consistent thickness and randomly distributed macro- and micro-pores. Mechanical conditioning from pulsatile flow bioreactor supported SMC orientation and enhanced ECM production in scaffolds. These results suggest that elastomeric scaffolds and mechanical conditioning of bioreactor culture may be a promising method for arterial tissue engineering.

Elastomeric PGS scaffolds with vascular smooth muscle cells cultured in a pulsatile flow bioreactor may lead to promising small-diameter arterial constructs with native ECM production in a relatively short culture period.

PGS elastomerico Ponteggi in Ingegneria tessuto arterioso

Cardiovascular disease is one of the leading cause of mortality in the US and especially, coronary artery disease increases with an aging population and ...

Ricerca

Bioingegneria

Postproduction Processing of Electrospun Fibres for Tissue Engineering

Electrospinning is a commonly used and versatile method to produce scaffolds (often biodegradable) for 3D tissue engineering.1, 2, 3 Many tissues in vivo undergo biaxial distension to varying extents such as skin, bladder, pelvic floor and even the hard palate as children grow. In producing scaffolds for these purposes there is a need to develop scaffolds of appropriate biomechanical properties (whether achieved without or with cells) and which are sterile for clinical use. The focus of this paper is not how to establish basic electrospinning parameters (as there is extensive literature on electrospinning) but on how to modify spun scaffolds post production to make them fit for tissue engineering purposes - here thickness, mechanical properties and sterilisation (required for clinical use) are considered and we also describe how cells can be cultured on scaffolds and subjected to biaxial strain to condition them for specific applications.
Electrospinning tends to produce thin sheets; as the electrospinning collector becomes coated with insulating fibres it becomes a poor conductor such that fibres no longer deposit on it. Hence we describe approaches to produce thicker structures by heat or vapour annealing increasing the strength of scaffolds but not necessarily the elasticity. Sequential spinning of scaffolds of different polymers to achieve complex scaffolds is also described. Sterilisation methodologies can adversely affect strength and elasticity of scaffolds. We compare three methods for their effects on the biomechanical properties on electrospun scaffolds of poly lactic-co-glycolic acid (PLGA).
Imaging of cells on scaffolds and assessment of production of extracellular matrix (ECM) proteins by cells on scaffolds is described. Culturing cells on scaffolds in vitro can improve scaffold strength and elasticity but the tissue engineering literature shows that cells often fail to produce appropriate ECM when cultured under static conditions. There are few commercial systems available that allow one to culture cells on scaffolds under dynamic conditioning regimes - one example is the Bose Electroforce 3100 which can be used to exert a conditioning programme on cells in scaffolds held using mechanical grips within a media filled chamber.4 An approach to a budget cell culture bioreactor for controlled distortion in 2 dimensions is described. We show that cells can be induced to produce elastin under these conditions. Finally assessment of the biomechanical properties of processed scaffolds cultured with or without cells is described.

Electrospun scaffolds can be processed post production for tissue engineering applications. Here we describe methods for spinning complex scaffolds (by consecutive spinning), for making thicker scaffolds (by multi-layering using heat or vapour annealing), for achieving sterility (aseptic production or sterilisation post production) and for achieving appropriate biomechanical properties.

Elaborazione Postproduzione di fibre elettrofilate per l&#39;ingegneria tissutale

Electrospinning is a commonly used and versatile method to produce  scaffolds (often biodegradable) for 3D tissue engineering.1, 2, 3 Many tissues in vivo ...

Electrospun Fibrous Scaffolds of Poly(glycerol-dodecanedioate) for Engineering Neural Tissues From Mouse Embryonic Stem Cells

For tissue engineering applications, the preparation of biodegradable and biocompatible scaffolds is the most desirable but challenging task. &#160;Among the various fabrication methods, electrospinning is the most attractive one due to its simplicity and versatility. Additionally, electrospun nanofibers mimic the size of natural extracellular matrix ensuring additional support for cell survival and growth. This study showed the viability of the fabrication of long fibers spanning a larger deposit area for a novel biodegradable and biocompatible polymer named&#160;poly(glycerol-dodecanoate) (PGD)1 by using a newly designed collector for electrospinning. PGD exhibits unique elastic properties with similar mechanical properties to nerve tissues, thus it is suitable for neural tissue engineering applications. The synthesis and fabrication set-up for making fibrous scaffolding materials was simple, highly reproducible, and inexpensive. In biocompatibility testing, cells derived from mouse embryonic stem cells could adhere to and grow on the electrospun PGD fibers. In summary, this protocol provided a versatile fabrication method for making PGD electrospun fibers to support the growth of mouse embryonic stem cell derived neural lineage cells.

Electrospun Fibrous Scaffolds of Polyglycerol-dodecanedioate for Engineering Neural Tissues From Mouse Embryonic Stem Cells

Synthesis and fabrication of electrospun long fibers spanning a larger deposit area via a newly designed collector from a novel biodegradable polymer named poly(glycerol-dodecanoate) (PGD) was reported. The fibers were able to support the growth of cells derived from mouse pluripotent stem cells.

Elettrofilate Fibrosa Ponteggi di Poli (glicerolo-dodecanedioate) per l&#39;ingegneria neurale tessuti da cellule staminali embrionali di topo

For tissue engineering applications, the preparation of biodegradable and biocompatible scaffolds is the most desirable but challenging task. &#160;Among ...

Optimizing Attachment of Human Mesenchymal Stem Cells on Poly(&#949;-caprolactone) Electrospun Yarns

Research into biomaterials and tissue engineering often includes cell-based in vitro investigations, which require initial knowledge of the starting cell number. While researchers commonly reference their seeding density this does not necessarily indicate the actual number of cells that have adhered to the material in question. This is particularly the case for materials, or scaffolds, that do not cover the base of standard cell culture well plates. This study investigates the initial attachment of human mesenchymal stem cells seeded at a known number onto electrospun poly(&#949;-caprolactone) yarn after 4 hr in culture. Electrospun yarns were held within several different set-ups, including bioreactor vessels rotating at 9 rpm, cell culture inserts positioned in low binding well plates and polytetrafluoroethylene (PTFE) troughs placed within petri dishes. The latter two were subjected to either static conditions or positioned on a shaker plate (30 rpm). After 4 hr incubation at 37&#160;oC, 5% CO2, the location of seeded cells was determined by cell DNA assay. Scaffolds were removed from their containers and placed in lysis buffer. The media fraction was similarly removed and centrifuged &#8211; the supernatant discarded and pellet broken up with lysis buffer. Lysis buffer was added to each receptacle, or well, and scraped to free any cells that may be present. The cell DNA assay determined the percentage of cells present within the scaffold, media and well fractions. Cell attachment was low for all experimental set-ups, with greatest attachment (30%) for yarns held within cell culture inserts and subjected to shaking motion. This study raises awareness to the actual number of cells attaching to scaffolds irrespective of the stated cell seeding density.

Optimizing Attachment of Human Mesenchymal Stem Cells on Poly(&amp;#949;-caprolactone) Electrospun Yarns

This article describes a range of set-ups for seeding human mesenchymal stem cells onto materials, in this case electrospun yarns, that do not cover the base of standard culture well plates in order to maximize and quantify the number of cells that initially attach compared to the known seeding density.

Ottimizzare Allegato di cellule staminali mesenchimali umane su Poli (ε-caprolattone) elettrofilate Filati

Research into biomaterials and tissue engineering often includes cell-based in vitro investigations, which require initial knowledge of the starting cell ...

Epithelial Cell Repopulation and Preparation of Rodent Extracellular Matrix Scaffolds for Renal Tissue Development

This protocol details the generation of acellular, yet biofunctional, renal extracellular matrix (ECM) scaffolds that are useful as small-scale model substrates for organ-scale tissue development. Sprague Dawley rat kidneys are cannulated by inserting a catheter into the renal artery and perfused with a series of low-concentration detergents (Triton X-100 and sodium dodecyl sulfate (SDS)) over 26 hr to derive intact, whole-kidney scaffolds with intact perfusable vasculature, glomeruli, and renal tubules. Following decellularization, the renal scaffold is placed inside a custom-designed perfusion bioreactor vessel, and the catheterized renal artery is connected to a perfusion circuit consisting of: a peristaltic pump; tubing; and optional probes for pH, dissolved oxygen, and pressure. After sterilizing the scaffold with peracetic acid and ethanol, and balancing the pH (7.4), the kidney scaffold is prepared for seeding via perfusion of culture medium within a large-capacity incubator maintained at 37 &#176;C and 5% CO2. Forty million renal cortical tubular epithelial (RCTE) cells are injected through the renal artery, and rapidly perfused through the scaffold under high flow (25 ml/min) and pressure (~230 mmHg) for 15 min before reducing the flow to a physiological rate (4 ml/min). RCTE cells primarily populate the tubular ECM niche within the renal cortex, proliferate, and form tubular epithelial structures over seven days of perfusion culture. A 44 &#181;M resazurin solution in culture medium is perfused through the kidney for 1 hr during medium exchanges to provide a fluorometric, redox-based metabolic assessment of cell viability and proliferation during tubulogenesis. The kidney perfusion bioreactor permits non-invasive sampling of medium for biochemical assessment, and multiple inlet ports allow alternative retrograde seeding through the renal vein or ureter. These protocols can be used to recellularize kidney scaffolds with a variety of cell types, including vascular endothelial, tubular epithelial, and stromal fibroblasts, for rapid evaluation within this system.

This protocol describes decellularization of Sprague Dawley rat kidneys by antegrade perfusion of detergents through the vasculature, producing acellular renal extracellular matrices that serve as templates for repopulation with human renal epithelial cells. Recellularization and use of the resazurin perfusion assay to monitor growth is performed within specially-designed perfusion bioreactors.

Ripopolamento cellule epiteliali e preparazione di roditori matrice extracellulare Ponteggi per lo sviluppo del tessuto renale

This protocol details the generation of acellular, yet biofunctional, renal extracellular matrix (ECM) scaffolds that are useful as small-scale model ...

Synthesis of Keratin-based Nanofiber for Biomedical Engineering

Electrospinning, due to its versatility and potential for applications in various fields, is being frequently used to fabricate nanofibers. Production of these porous nanofibers is of great interest due to their unique physiochemical properties. Here we elaborate on the fabrication of keratin containing poly (&#949;-caprolactone) (PCL) nanofibers (i.e., PCL/keratin composite fiber). Water soluble keratin was first extracted from human hair and mixed with PCL in different ratios. The blended solution of PCL/keratin was transformed into nanofibrous membranes using a laboratory designed electrospinning set up. Fiber morphology and mechanical properties of the obtained nanofiber were observed and measured using scanning electron microscopy and tensile tester. Furthermore, degradability and chemical properties of the nanofiber were studied by FTIR. SEM images showed uniform surface morphology for PCL/keratin fibers of different compositions. These PCL/keratin fibers also showed excellent mechanical properties such as Young&#39;s modulus and failure point. Fibroblast cells were able to attach and proliferate thus proving good cell viability. Based on the characteristics discussed above, we can strongly argue that the blended nanofibers of natural and synthetic polymers can represent an excellent development of composite materials that can be used for different biomedical applications.

Electrospun nanofibers have a high surface area to weight ratio, excellent mechanical integrity, and support cell growth and proliferation. These nanofibers have a wide range of biomedical applications. Here we fabricate keratin/ PCL nanofibers, using the electrospinning technique, and characterize the fibers for possible applications in tissue engineering.

Sintesi di nanofibre cheratina-based per Ingegneria Biomedica

Electrospinning, due to its versatility and potential for applications in various fields, is being frequently used to fabricate nanofibers. Production of ...

A Facile and Eco-friendly Route to Fabricate Poly(Lactic Acid) Scaffolds with Graded Pore Size

Over the recent years, functionally graded scaffolds (FGS) gaineda crucial role for manufacturing of devices for tissue engineering. The importance of this new field of biomaterials research is due to the necessity to develop implants capable of mimicking the complex functionality of the various tissues, including a continuous change from one structure or composition to another. In this latter context, one topic of main interest concerns the design of appropriate scaffolds for bone-cartilage interface tissue. In this study, three-layered scaffolds with graded pore size were achieved by melt mixing poly(lactic acid) (PLA), sodium chloride (NaCl) and polyethylene glycol (PEG). Pore size distributions were controlled by NaCl granulometry and PEG solvation. Scaffolds were characterized from a morphological and mechanical point of view. A correlation between the preparation method, the pore architecture and compressive mechanical behavior was found. The interface adhesion strength was quantitatively evaluated by using a custom-designed interfacial strength test. Furthermore, in order to imitate the human physiology, mechanical tests were also performed in phosphate buffered saline (PBS) solution at 37 &#176;C. The method herein presented provides a high control of porosity, pore size distribution and mechanical performance, thus offering the possibility to fabricate three-layered scaffolds with tailored properties by following a simple and eco-friendly route.

A Facile and Eco-friendly Route to Fabricate PolyLactic Acid Scaffolds with Graded Pore Size

In this work, poly(lactic acid)/polyethylene glycol (PLA/PEG) scaffolds were prepared by using a combination of melt mixing and selective leaching. The method herein discussed permitted to develop three-layer scaffolds by highly controlling both porosity and pore size. The mechanical properties were also evaluated in a physiological environment.

Un Facile ed ecologico percorso per fabbricare poli (acido lattico) Ponteggi con Graded dimensione dei pori

Over the recent years, functionally graded scaffolds (FGS) gaineda crucial role for manufacturing of devices for tissue engineering. The importance of ...

Melt Electrospinning Writing of Three-dimensional Poly(&#949;-caprolactone) Scaffolds with Controllable Morphologies for Tissue Engineering Applications

This tutorial reflects on the fundamental principles and guidelines for electrospinning writing with polymer melts, an additive manufacturing technology with great potential for biomedical applications. The technique facilitates the direct deposition of biocompatible polymer fibers to fabricate well-ordered scaffolds in the sub-micron to micro scale range. The establishment of a stable, viscoelastic, polymer jet between a spinneret and a collector is achieved using an applied voltage and can be direct-written. A significant benefit of a typical porous scaffold is a high surface-to-volume ratio which provides increased effective adhesion sites for cell attachment and growth. Controlling the printing process by fine-tuning the system parameters enables high reproducibility in the quality of the printed scaffolds. It also provides a flexible manufacturing platform for users to tailor the morphological structures of the scaffolds to their specific requirements. For this purpose, we present a protocol to obtain different fiber diameters using melt electrospinning writing (MEW) with a guided amendment of the parameters, including flow rate, voltage and collection speed. Furthermore, we demonstrate how to optimize the jet, discuss often experienced technical challenges, explain troubleshooting techniques and showcase a wide range of printable scaffold architectures.

Melt Electrospinning Writing of Three-dimensional Poly(&amp;#949;-caprolactone) Scaffolds with Controllable Morphologies for Tissue Engineering Applications

This protocol serves as a comprehensive guideline to fabricate scaffolds via electrospinning with polymer melts in a direct writing mode. We systematically outline the process and define the appropriate parameter settings for achieving targeted scaffold architectures.

Sciogliere elettrofilatura scrittura di scaffold tridimensionale Poly(ε-caprolactone) con morfologie controllabile per applicazioni di ingegneria del tessuto

This tutorial reflects on the fundamental principles and guidelines for electrospinning writing with polymer melts, an additive manufacturing technology ...

Fabrication and Characterization of Griffithsin-modified Fiber Scaffolds for Prevention of Sexually Transmitted Infections

Electrospun fibers (EFs) have been widely used in a variety of therapeutic applications; however, they have only recently been applied as a technology to prevent and treat sexually transmitted infections (STIs). Moreover, many EF technologies focus on encapsulating the active agent, relative to utilizing the surface to impart biofunctionality. Here we describe a method to fabricate and surface-modify poly(lactic-co-glycolic) acid (PLGA) electrospun fibers, with the potent antiviral lectin Griffithsin (GRFT). PLGA is an FDA-approved polymer that has been widely used in drug delivery due to its outstanding chemical and biocompatible properties. GRFT is a natural, potent, and safe lectin that possesses broad activity against numerous viruses including human immunodeficiency virus type 1 (HIV-1). When combined, GRFT-modified fibers have demonstrated potent inactivation of HIV-1 in vitro. This manuscript describes the methods to fabricate and characterize GRFT-modified EFs. First, PLGA is electrospun to create a fiber scaffold. Fibers are subsequently surface-modified with GRFT using 1-Ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC) and N-hydroxysuccinimide (NHS)chemistry. Scanning electron microscopy (SEM) was used to assess the size and morphology of surface-modified formulations. Additionally, a gp120 or hemagglutinin (HA)-based ELISA may be used to quantify the amount of GRFT conjugated to, as well as GRFT desorption from the fiber surface. This protocol can be more widely applied to fabricate fibers that are surface-modified with a variety of different proteins.

This manuscript describes the procedure to fabricate and characterize Griffithsin-modified poly(lactic-co-glycolic acid) electrospun fibers that demonstrate potent adhesive and antiviral activity against human immunodeficiency virus type 1 infection in vitro. Methods used to synthesize, surface-modify, and characterize the resulting morphology, conjugation, and desorption of Griffithsin from surface-modified fibers are described.

Fabbricazione e caratterizzazione di fibra Griffithsin-modificato ponteggi per la prevenzione delle infezioni sessualmente trasmesse

Electrospun fibers (EFs) have been widely used in a variety of therapeutic applications; however, they have only recently been applied as a technology to ...

Culturing Mammalian Cells in Three-dimensional Peptide Scaffolds

A useful technique for culturing cells in a self-assembling nanofiber three-dimensional (3D) scaffold is described. This culture system recreates an environment that closely mimics the structural features of non-polarized tissue. Furthermore, the particular intrinsic nanofiber structure of the scaffold makes it transparent to visual light, which allows for easy visualization of the sample under microscopy. This advantage was largely used to study cell migration, organization, proliferation, and differentiation and thus any development of their particular cellular function by staining with specific dyes or probes. Furthermore, in this work, we describe the good performance of this system to easily study the redifferentiation of expanded human articular chondrocytes into cartilaginous tissue. Cells were encapsulated into self-assembling peptide scaffolds and cultured under specific conditions to promote chondrogenesis. Three-dimensional cultures showed good viability during the 4 weeks of the experiment. As expected, samples cultured with chondrogenic inducers (compared to non-induced controls) stained strongly positive for toluidine blue (which stains glycosaminoglycans (GAGs) that are highly present in cartilage extracellular matrix) and expressed specific molecular markers, including collagen type I, II and X, according to Western Blot analysis. This protocol is easy to perform and can be used at research laboratories, industries and for educational purposes in laboratory courses.

Here, we present a protocol to obtain 3D-culture systems in self-assembling peptide scaffolds to promote the differentiation of dedifferentiated human articular chondrocytes into cartilage-like tissue.

Coltura di cellule di mammifero in scaffold tridimensionale Peptide

A useful technique for culturing cells in a self-assembling nanofiber three-dimensional (3D) scaffold is described. This culture system recreates an ...